Add Colorspace connector property interface
Subsystems (3)
v2 cover Add Colorspace connector property interface
This patch series creates a new connector property to program colorspace to sink devices. Modern sink devices support more than 1 type of colorspace like 601, 709, BT2020 etc. This helps to switch based on content type which is to be displayed. The decision lies with compositors as to in which scenarios, a particular colorspace will be picked.
This will be helpful mostly to switch to higher gamut colorspaces like BT2020 when the media content is encoded as BT2020. Thereby giving a good visual experience to users.
The expectation from userspace is that it should parse the EDID and get supported colorspaces. Use this property and switch to the one supported. Kernel will not give the supported colorspaces since this is panel dependent and our curremt property infrastructure is not supporting it.
Have tested this using xrandr by using below command:
xrandr --output HDMI2 --set "Colorspace" "BT2020_rgb"
v2: Addressed Ville and Maarten's review comments. Merged the 2nd and 3rd patch into one common logical patch.
Uma Shankar (2):
drm: Add colorspace property
drm/i915: Attach colorspace property and enable modeset
drivers/gpu/drm/drm_atomic_uapi.c | 4 ++++ drivers/gpu/drm/drm_connector.c | 44 +++++++++++++++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_atomic.c | 1 + drivers/gpu/drm/i915/intel_hdmi.c | 5 +++++ include/drm/drm_connector.h | 7 ++++++ include/drm/drm_mode_config.h | 6 +++++ include/uapi/drm/drm_mode.h | 24 ++++++++++++++++++++ 7 files changed, 91 insertions(+)
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v2 1/2 drm: Add colorspace property
This patch adds a colorspace property enabling userspace to switch to various supported colorspaces. This will help enable BT2020 along with other colorspaces.
v2: Addressed Maarten and Ville's review comments. Enhanced the colorspace enum to incorporate both HDMI and DP supported colorspaces. Also, added a default option for colorspace.
--- drivers/gpu/drm/drm_atomic_uapi.c | 4 ++++ drivers/gpu/drm/drm_connector.c | 44 +++++++++++++++++++++++++++++++++++++++ include/drm/drm_connector.h | 7 +++++++ include/drm/drm_mode_config.h | 6 ++++++ include/uapi/drm/drm_mode.h | 24 +++++++++++++++++++++ 5 files changed, 85 insertions(+)
drivers/gpu/drm/drm_atomic_uapi.c +4 -0
@@ -721,6 +721,8 @@ static int drm_atomic_connector_set_property(struct drm_connector *connector, state->picture_aspect_ratio = val; }else if (property == config->content_type_property) { state->content_type = val; + }else if (property == config->colorspace_property) { + state->colorspace = val; }else if (property == connector->scaling_mode_property) { state->scaling_mode = val; }else if (property == connector->content_protection_property) {
@@ -795,6 +797,8 @@ static int drm_atomic_connector_set_property(struct drm_connector *connector, *val = state->picture_aspect_ratio; }else if (property == config->content_type_property) { *val = state->content_type; + }else if (property == config->colorspace_property) { + *val = state->colorspace; }else if (property == connector->scaling_mode_property) { *val = state->scaling_mode; }else if (property == connector->content_protection_property) {
drivers/gpu/drm/drm_connector.c +44 -0
62 lines not on this page · raw message
include/drm/drm_connector.h +7 -0
@@ -497,6 +497,13 @@ struct drm_connector_state {unsigned int content_protection;/** +* @colorspace: Connector property to request colorspace +* change. This is most commonly used to switch to wider color +* gamuts like BT2020. +*/ +enum encoder_colorimetry colorspace; + +/** * @writeback_job: Writeback job for writeback connectors * * Holds the framebuffer and out-fence for a writeback connector. As
include/drm/drm_mode_config.h +6 -0
@@ -863,6 +863,12 @@ struct drm_mode_config {uint32_t cursor_width, cursor_height;/** +* @colorspace_property: Connector property to set the suitable +* colorspace supported by the sink. +*/ +struct drm_property *colorspace_property; + +/** * @suspend_state: * * Atomic state when suspended.
include/uapi/drm/drm_mode.h +24 -0
@@ -210,6 +210,30 @@#define DRM_MODE_CONTENT_PROTECTION_DESIRED 1#define DRM_MODE_CONTENT_PROTECTION_ENABLED 2 +enum encoder_colorimetry { +/* CEA 861 Normal Colorimetry options */ +COLORIMETRY_ITU_601 =0 , +COLORIMETRY_ITU_709 , +/* CEA 861 Extended Colorimetry Options */ +COLORIMETRY_XV_YCC_601 , +COLORIMETRY_XV_YCC_709 , +COLORIMETRY_S_YCC_601 , +COLORIMETRY_ADOBE_YCC_601 , +COLORIMETRY_ADOBE_RGB , +COLORIMETRY_BT2020_RGB , +COLORIMETRY_BT2020_YCC , +COLORIMETRY_BT2020_CYCC , +/* DP MSA Colorimetry Options */ +COLORIMETRY_Y_CBCR_ITU_601 , +COLORIMETRY_Y_CBCR_ITU_709 , +COLORIMETRY_SRGB , +COLORIMETRY_RGB_WIDE_GAMUT , +COLORIMETRY_SCRGB , +COLORIMETRY_DCI_P3 , +COLORIMETRY_CUSTOM_COLOR_PROFILE , +COLORIMETRY_DEFAULT =COLORIMETRY_ITU_709 , +}; +struct drm_mode_modeinfo {__u32 clock;__u16 hdisplay;
Signature · 6 lines
1.9.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Maarten Lankhorst
maintainerRe: [Intel-gfx] [v2 1/2] drm: Add colorspace property
Op 31-10-18 om 13:05 schreef Uma Shankar:
Quoted 45 lines
This patch adds a colorspace property enabling userspace to switch to various supported colorspaces. This will help enable BT2020 along with other colorspaces.
v2: Addressed Maarten and Ville's review comments. Enhanced the colorspace enum to incorporate both HDMI and DP supported colorspaces. Also, added a default option for colorspace.
Signed-off-by Uma Shankar <[email protected]>--- drivers/gpu/drm/drm_atomic_uapi.c | 4 ++++ drivers/gpu/drm/drm_connector.c | 44 +++++++++++++++++++++++++++++++++++++++ include/drm/drm_connector.h | 7 +++++++ include/drm/drm_mode_config.h | 6 ++++++ include/uapi/drm/drm_mode.h | 24 +++++++++++++++++++++ 5 files changed, 85 insertions(+)drivers/gpu/drm/drm_atomic_uapi.c +4
-0@@ -721,6 +721,8 @@ static int drm_atomic_connector_set_property(struct drm_connector *connector, state->picture_aspect_ratio = val; }else if (property == config->content_type_property) { state->content_type = val; + }else if (property == config->colorspace_property) { + state->colorspace = val; }else if (property == connector->scaling_mode_property) { state->scaling_mode = val; }else if (property == connector->content_protection_property) {@@ -795,6 +797,8 @@ static int drm_atomic_connector_set_property(struct drm_connector *connector, *val = state->picture_aspect_ratio; }else if (property == config->content_type_property) { *val = state->content_type; + }else if (property == config->colorspace_property) { + *val = state->colorspace; }else if (property == connector->scaling_mode_property) { *val = state->scaling_mode; }else if (property == connector->content_protection_property) {drivers/gpu/drm/drm_connector.c +0
-0@@ -826,6 +826,38 @@ int drm_display_info_set_bus_formats(struct drm_display_info *info, };
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 836
Quoted 10 lines
drivers/gpu/drm/drm_connector.c +8
-0DRM_ENUM_NAME_FN(drm_get_content_protection_name, drm_cp_enum_list) +static const struct drm_prop_enum_list colorspace[] = { +/* Standard Definition Colorimetry based on CEA 861 */ + {COLORIMETRY_ITU_601 ,"601" }, + {COLORIMETRY_ITU_709 ,"709" }, +/* Standard Definition Colorimetry based on IEC 61966-2-4 */ + {COLORIMETRY_XV_YCC_601 ,"601" }, +/* High Definition Colorimetry based on IEC 61966-2-4 */ + {COLORIMETRY_XV_YCC_709 ,"709" },
2 definitions that share the same name?
All in all, I think the enum strings need to be more descriptive and self-consistent.
Quoted 6 lines
drivers/gpu/drm/drm_connector.c +6
-0+/* Colorimetry based on IEC 61966-2-1/Amendment 1 */ + { COLORIMETRY_S_YCC_601, "s601" }, +/* Colorimetry based on IEC 61966-2-5 [33] */ + { COLORIMETRY_ADOBE_YCC_601, "adobe601" }, +/* Colorimetry based on IEC 61966-2-5 */ + { COLORIMETRY_ADOBE_RGB, "adobe_rgb" },
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 852
Quoted 10 lines
drivers/gpu/drm/drm_connector.c +10
-0+/* Colorimetry based on ITU-R BT.2020 */ + { COLORIMETRY_BT2020_RGB, "BT2020_rgb" }, +/* Colorimetry based on ITU-R BT.2020 */ + { COLORIMETRY_BT2020_YCC, "BT2020_ycc" }, +/* Colorimetry based on ITU-R BT.2020 */ + { COLORIMETRY_BT2020_CYCC, "BT2020_cycc" }, +/* DP MSA Colorimetry */ + { COLORIMETRY_Y_CBCR_ITU_601, "YCBCR_ITU_601" }, + { COLORIMETRY_Y_CBCR_ITU_709, "YCBCR_ITU_709" }, + { COLORIMETRY_SRGB, "SRGB" },
sRGB
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 854
Quoted 2 lines
drivers/gpu/drm/drm_connector.c +2
-0+ { COLORIMETRY_RGB_WIDE_GAMUT, "RGB Wide Gamut" }, + { COLORIMETRY_SCRGB, "SCRGB" },
scRGB?
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 855
Quoted 1 line
drivers/gpu/drm/drm_connector.c +1
-0+ { COLORIMETRY_DCI_P3, "DCIP3" },
DCI-P3?
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 856
Quoted 1 line
drivers/gpu/drm/drm_connector.c +1
-0+ { COLORIMETRY_CUSTOM_COLOR_PROFILE, "Custom Proflie" },
^Typo
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 858
Quoted 2 lines
drivers/gpu/drm/drm_connector.c +2
-0+/* FOR HD 720p+, Default Colorimetry is based on ITU-R BT.709 */ + { COLORIMETRY_DEFAULT, "Default: ITU_709" },
This enum together with the code below is broken.
+ COLORIMETRY_DEFAULT = COLORIMETRY_ITU_709,
I would just make it COLORIMETRY_UNSET = "Unset".
To set the default colorimetry for all drivers, just make the default value 0 (preferred), or add it to __drm_atomic_helper_connector_reset().
Quoted 91 lines
drivers/gpu/drm/drm_connector.c +14
-0+}; +/** * DOC: standard connector properties * @@ -972,6 +1004,12 @@ int drm_display_info_set_bus_formats(struct drm_display_info *info,* can also expose this property to external outputs, in which case they * must support "None", which should be the default (since external screens * have a built-in scaler). +* +* colorspace: +* This property helps select a suitable colorspace based on the sink +* capability. Modern sink devices support wider gamut like BT2020. +* This helps switch to BT2020 mode if the BT2020 encoded video stream +* is being played by the user, same for any other colorspace. */ int drm_connector_create_standard_properties (struct drm_device *dev)@@ -1020,6 +1058,12 @@ int drm_connector_create_standard_properties(struct drm_device *dev)return -ENOMEM ; dev->mode_config.non_desktop_property = prop; + prop =drm_property_create_enum (dev,DRM_MODE_PROP_ENUM ,"Colorspace" , + colorspace,ARRAY_SIZE (colorspace)); +if (!prop) +return -ENOMEM ; + dev->mode_config.colorspace_property = prop; +return 0 ; }include/drm/drm_connector.h +7
-0@@ -497,6 +497,13 @@ struct drm_connector_state {unsigned int content_protection;/** +* @colorspace: Connector property to request colorspace +* change. This is most commonly used to switch to wider color +* gamuts like BT2020. +*/ +enum encoder_colorimetry colorspace; + +/** * @writeback_job: Writeback job for writeback connectors * * Holds the framebuffer and out-fence for a writeback connector. As include/drm/drm_mode_config.h +6
-0@@ -863,6 +863,12 @@ struct drm_mode_config {uint32_t cursor_width, cursor_height;/** +* @colorspace_property: Connector property to set the suitable +* colorspace supported by the sink. +*/ +struct drm_property *colorspace_property; + +/** * @suspend_state: * * Atomic state when suspended. include/uapi/drm/drm_mode.h +17
-0@@ -210,6 +210,30 @@#define DRM_MODE_CONTENT_PROTECTION_DESIRED 1#define DRM_MODE_CONTENT_PROTECTION_ENABLED 2 +enum encoder_colorimetry { +/* CEA 861 Normal Colorimetry options */ +COLORIMETRY_ITU_601 =0 , +COLORIMETRY_ITU_709 , +/* CEA 861 Extended Colorimetry Options */ +COLORIMETRY_XV_YCC_601 , +COLORIMETRY_XV_YCC_709 , +COLORIMETRY_S_YCC_601 , +COLORIMETRY_ADOBE_YCC_601 , +COLORIMETRY_ADOBE_RGB , +COLORIMETRY_BT2020_RGB , +COLORIMETRY_BT2020_YCC , +COLORIMETRY_BT2020_CYCC , +/* DP MSA Colorimetry Options */ +COLORIMETRY_Y_CBCR_ITU_601 , +COLORIMETRY_Y_CBCR_ITU_709 , +COLORIMETRY_SRGB ,
include/uapi/drm/drm_mode.h line 239
Quoted 10 lines
include/uapi/drm/drm_mode.h +7
-0+ COLORIMETRY_RGB_WIDE_GAMUT, +COLORIMETRY_SCRGB , +COLORIMETRY_DCI_P3 , +COLORIMETRY_CUSTOM_COLOR_PROFILE , + COLORIMETRY_DEFAULT = COLORIMETRY_ITU_709, +}; +struct drm_mode_modeinfo {__u32 clock;__u16 hdisplay;
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [Intel-gfx] [v2 1/2] drm: Add colorspace property
Quoted 48 lines · Maarten Lankhorst
Op 31-10-18 om 13:05 schreef Uma Shankar:
Quoted 47 lines
This patch adds a colorspace property enabling userspace to switch to various supported colorspaces. This will help enable BT2020 along with other colorspaces.
v2: Addressed Maarten and Ville's review comments. Enhanced the colorspace enum to incorporate both HDMI and DP supported colorspaces. Also, added a default option for colorspace.
Signed-off-by Uma Shankar <[email protected]>--- drivers/gpu/drm/drm_atomic_uapi.c | 4 ++++ drivers/gpu/drm/drm_connector.c | 44 +++++++++++++++++++++++++++++++++++++++ include/drm/drm_connector.h | 7 +++++++ include/drm/drm_mode_config.h | 6 ++++++ include/uapi/drm/drm_mode.h | 24 +++++++++++++++++++++ 5 files changed, 85 insertions(+)drivers/gpu/drm/drm_atomic_uapi.c +4
-0@@ -721,6 +721,8 @@ static int drm_atomic_connector_set_property(struct drm_connector *connector, state->picture_aspect_ratio = val; }else if (property == config->content_type_property) { state->content_type = val; + }else if (property == config->colorspace_property) { + state->colorspace = val; }else if (property == connector->scaling_mode_property) { state->scaling_mode = val; }else if (property == connector->content_protection_property) {@@ -795,6 +797,8 @@ static int drm_atomic_connector_set_property(struct drm_connector *connector, *val = state->picture_aspect_ratio; }else if (property == config->content_type_property) { *val = state->content_type; + }else if (property == config->colorspace_property) { + *val = state->colorspace; }else if (property == connector->scaling_mode_property) { *val = state->scaling_mode; }else if (property == connector->content_protection_property) {drivers/gpu/drm/drm_connector.c +0
-0@@ -826,6 +826,38 @@ int drm_display_info_set_bus_formats(struct drm_display_info *info, };DRM_ENUM_NAME_FN (drm_get_content_protection_name, drm_cp_enum_list)
Quoted 10 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 836
Quoted 8 lines
drivers/gpu/drm/drm_connector.c +8
-0+static const struct drm_prop_enum_list colorspace[] = { +/* Standard Definition Colorimetry based on CEA 861 */ + {COLORIMETRY_ITU_601 ,"601" }, + {COLORIMETRY_ITU_709 ,"709" }, +/* Standard Definition Colorimetry based on IEC 61966-2-4 */ + {COLORIMETRY_XV_YCC_601 ,"601" }, +/* High Definition Colorimetry based on IEC 61966-2-4 */ + {COLORIMETRY_XV_YCC_709 ,"709" },2 definitions that share the same name?
All in all, I think the enum strings need to be more descriptive and self-consistent.
+1
Quoted 4 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 840
Quoted 4 lines
drivers/gpu/drm/drm_connector.c +4
-0+/* Colorimetry based on IEC 61966-2-1/Amendment 1 */ + { COLORIMETRY_S_YCC_601, "s601" }, +/* Colorimetry based on IEC 61966-2-5 [33] */ + { COLORIMETRY_ADOBE_YCC_601, "adobe601" },
Hans (cc:d) recetly noted that these things aren't called Adobe<something> anymore in the CTA-861 spec. There is some new name for them, which I now forget.
Quoted 26 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 852
Quoted 12 lines
drivers/gpu/drm/drm_connector.c +12
-0+/* Colorimetry based on IEC 61966-2-5 */ + { COLORIMETRY_ADOBE_RGB, "adobe_rgb" }, +/* Colorimetry based on ITU-R BT.2020 */ + { COLORIMETRY_BT2020_RGB, "BT2020_rgb" }, +/* Colorimetry based on ITU-R BT.2020 */ + { COLORIMETRY_BT2020_YCC, "BT2020_ycc" }, +/* Colorimetry based on ITU-R BT.2020 */ + { COLORIMETRY_BT2020_CYCC, "BT2020_cycc" }, +/* DP MSA Colorimetry */ + { COLORIMETRY_Y_CBCR_ITU_601, "YCBCR_ITU_601" }, + { COLORIMETRY_Y_CBCR_ITU_709, "YCBCR_ITU_709" }, + { COLORIMETRY_SRGB, "SRGB" },sRGB
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 854
Quoted 2 lines
drivers/gpu/drm/drm_connector.c +2
-0+ { COLORIMETRY_RGB_WIDE_GAMUT, "RGB Wide Gamut" }, + { COLORIMETRY_SCRGB, "SCRGB" },scRGB?
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 855
Quoted 1 line
drivers/gpu/drm/drm_connector.c +1
-0+ { COLORIMETRY_DCI_P3, "DCIP3" },DCI-P3?
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 856
Quoted 1 line
drivers/gpu/drm/drm_connector.c +1
-0+ { COLORIMETRY_CUSTOM_COLOR_PROFILE, "Custom Proflie" },^Typo
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 858
Quoted 2 lines
drivers/gpu/drm/drm_connector.c +2
-0+/* FOR HD 720p+, Default Colorimetry is based on ITU-R BT.709 */ + { COLORIMETRY_DEFAULT, "Default: ITU_709" },This enum together with the code below is broken.
include/uapi/drm/drm_mode.h +1
-0+ COLORIMETRY_DEFAULT = COLORIMETRY_ITU_709,
Quoted 1 line
I would just make it
COLORIMETRY_UNSET= "Unset".
"Unset" might work. Though feels a bit strange to me. Other ideas would be "Default", "Automatic", "Undefined" or something along those lines. Ideally it should convey the meaning of "the driver will pick this for you", and for that I'd lean towards "Default" or "Automatic".
Quoted 111 lines
To set the default colorimetry for all drivers, just make the default value 0 (preferred), or add it to
__drm_atomic_helper_connector_reset().Quoted 91 lines
drivers/gpu/drm/drm_connector.c +14
-0+}; +/** * DOC: standard connector properties * @@ -972,6 +1004,12 @@ int drm_display_info_set_bus_formats(struct drm_display_info *info,* can also expose this property to external outputs, in which case they * must support "None", which should be the default (since external screens * have a built-in scaler). +* +* colorspace: +* This property helps select a suitable colorspace based on the sink +* capability. Modern sink devices support wider gamut like BT2020. +* This helps switch to BT2020 mode if the BT2020 encoded video stream +* is being played by the user, same for any other colorspace. */ int drm_connector_create_standard_properties (struct drm_device *dev)@@ -1020,6 +1058,12 @@ int drm_connector_create_standard_properties(struct drm_device *dev)return -ENOMEM ; dev->mode_config.non_desktop_property = prop; + prop =drm_property_create_enum (dev,DRM_MODE_PROP_ENUM ,"Colorspace" , + colorspace,ARRAY_SIZE (colorspace)); +if (!prop) +return -ENOMEM ; + dev->mode_config.colorspace_property = prop; +return 0 ; }include/drm/drm_connector.h +7
-0@@ -497,6 +497,13 @@ struct drm_connector_state {unsigned int content_protection;/** +* @colorspace: Connector property to request colorspace +* change. This is most commonly used to switch to wider color +* gamuts like BT2020. +*/ +enum encoder_colorimetry colorspace; + +/** * @writeback_job: Writeback job for writeback connectors * * Holds the framebuffer and out-fence for a writeback connector. As include/drm/drm_mode_config.h +6
-0@@ -863,6 +863,12 @@ struct drm_mode_config {uint32_t cursor_width, cursor_height;/** +* @colorspace_property: Connector property to set the suitable +* colorspace supported by the sink. +*/ +struct drm_property *colorspace_property; + +/** * @suspend_state: * * Atomic state when suspended. include/uapi/drm/drm_mode.h +17
-0@@ -210,6 +210,30 @@#define DRM_MODE_CONTENT_PROTECTION_DESIRED 1#define DRM_MODE_CONTENT_PROTECTION_ENABLED 2 +enum encoder_colorimetry { +/* CEA 861 Normal Colorimetry options */ +COLORIMETRY_ITU_601 =0 , +COLORIMETRY_ITU_709 , +/* CEA 861 Extended Colorimetry Options */ +COLORIMETRY_XV_YCC_601 , +COLORIMETRY_XV_YCC_709 , +COLORIMETRY_S_YCC_601 , +COLORIMETRY_ADOBE_YCC_601 , +COLORIMETRY_ADOBE_RGB , +COLORIMETRY_BT2020_RGB , +COLORIMETRY_BT2020_YCC , +COLORIMETRY_BT2020_CYCC , +/* DP MSA Colorimetry Options */ +COLORIMETRY_Y_CBCR_ITU_601 , +COLORIMETRY_Y_CBCR_ITU_709 , +COLORIMETRY_SRGB ,include/uapi/drm/drm_mode.h line 239
Quoted 10 lines
include/uapi/drm/drm_mode.h +7
-0+ COLORIMETRY_RGB_WIDE_GAMUT, +COLORIMETRY_SCRGB , +COLORIMETRY_DCI_P3 , +COLORIMETRY_CUSTOM_COLOR_PROFILE , + COLORIMETRY_DEFAULT = COLORIMETRY_ITU_709, +}; +struct drm_mode_modeinfo {__u32 clock;__u16 hdisplay;_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Signature · 6 lines
Ville Syrjälä Intel _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [v2 1/2] drm: Add colorspace property
Quoted 76 lines
-----Original Message-----
From: Ville Syrjälä [mailto:[email protected]]
Sent: Friday, November 2, 2018 5:00 PM
To: Maarten Lankhorst <[email protected]>
Cc: Shankar, Uma <[email protected]>; [email protected]; [email protected]; Syrjala, Ville <[email protected]>; Lankhorst, Maarten <[email protected]>; Hans Verkuil <[email protected]>
Subject: Re: [Intel-gfx] [v2 1/2] drm: Add colorspace propertyQuoted 13 lines · Maarten Lankhorst
Op 31-10-18 om 13:05 schreef Uma Shankar:
Quoted 12 lines
This patch adds a colorspace property enabling userspace to switch to various supported colorspaces.
This will help enable BT2020 along with other colorspaces.v2: Addressed Maarten and Ville's review comments. Enhanced the colorspace enum to incorporate both HDMI and DP supported colorspaces. Also, added a default option for colorspace.
Signed-off-by Uma Shankar <[email protected]>--- drivers/gpu/drm/drm_atomic_uapi.c | 4 ++++ drivers/gpu/drm/drm_connector.c | 44+++++++++++++++++++++++++++++++++++++++
Quoted 11 lines
drivers/gpu/drm/drm_atomic_uapi.c static int drm_atomic_connector_set_property(struct
Quoted 11 lines
include/drm/drm_connector.h | 7 +++++++ include/drm/drm_mode_config.h | 6 ++++++ include/uapi/drm/drm_mode.h | 24 +++++++++++++++++++++ 5 files changed, 85 insertions(+)drivers/gpu/drm/drm_atomic_uapi.c +0
-0@@ -721,6 +721,8 @@ static int drm_atomic_connector_set_property(struct
drm_connector*connector,Quoted 9 lines
drivers/gpu/drm/drm_atomic_uapi.c static int drm_atomic_connector_set_property(struct
Quoted 9 lines
drivers/gpu/drm/drm_atomic_uapi.c +2
-0state->picture_aspect_ratio = val; }else if (property == config->content_type_property) { state->content_type = val; + }else if (property == config->colorspace_property) { + state->colorspace = val; }else if (property == connector->scaling_mode_property) { state->scaling_mode = val; }else if (property == connector->content_protection_property) {@@ -795,6 +797,8 @@ static int drm_atomic_connector_set_property(struct
drm_connector*connector,Quoted 7 lines
Quoted 7 lines
drivers/gpu/drm/drm_atomic_uapi.c +2
-0*val = state->picture_aspect_ratio; }else if (property == config->content_type_property) { *val = state->content_type; + }else if (property == config->colorspace_property) { + *val = state->colorspace; }else if (property == connector->scaling_mode_property) { *val = state->scaling_mode;Quoted 8 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct · line 827
Quoted 8 lines
drivers/gpu/drm/drm_atomic_uapi.c +0
-0}else if (property == connector->content_protection_property) {(quoted diff) +0
-0
b/drivers/gpu/drm/drm_connector.cindex aa18b1d..5ad52a0 100644drivers/gpu/drm/drm_connector.c +0
-0@@ -826,6 +826,38 @@ int drm_display_info_set_bus_formats(struct drm_display_info *info, }; DRM_ENUM_NAME_FN(drm_get_content_protection_name,
drm_cp_enum_list)Quoted 11 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 836
Quoted 9 lines
drivers/gpu/drm/drm_connector.c +8
-0+static const struct drm_prop_enum_list colorspace[] = { +/* Standard Definition Colorimetry based on CEA 861 */ + {COLORIMETRY_ITU_601 ,"601" }, + {COLORIMETRY_ITU_709 ,"709" }, +/* Standard Definition Colorimetry based on IEC 61966-2-4 */ + {COLORIMETRY_XV_YCC_601 ,"601" }, +/* High Definition Colorimetry based on IEC 61966-2-4 */ + {COLORIMETRY_XV_YCC_709 ,"709" },2 definitions that share the same name?
All in all, I think the enum strings need to be more descriptive and self-
Quoted 2 lines
consistent.
+1
Sure, will modify this.
Quoted 8 lines
Quoted 4 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 840
Quoted 4 lines
drivers/gpu/drm/drm_connector.c +4
-0+/* Colorimetry based on IEC 61966-2-1/Amendment 1 */ + { COLORIMETRY_S_YCC_601, "s601" }, +/* Colorimetry based on IEC 61966-2-5 [33] */ + { COLORIMETRY_ADOBE_YCC_601, "adobe601" },Hans (cc:d) recetly noted that these things aren't called Adobe<something> anymore in the CTA-861 spec. There is some new name for them, which I now forget.
EC2 EC1 EC0 Extended Colorimetry
0 1 1 AdobeYCC601
This is the bit format mentioned in CEA861.F while defining the AVI infoframe, so looks like they are still keeping it that way. Not sure if its updated as part of any latest spec update.
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
drivers/gpu/drm/drm_connector.c +5
-0+/* Colorimetry based on IEC 61966-2-5 */ + { COLORIMETRY_ADOBE_RGB, "adobe_rgb" }, +/* Colorimetry based on ITU-R BT.2020 */ + { COLORIMETRY_BT2020_RGB, "BT2020_rgb" }, +/* Colorimetry based on ITU-R BT.2020 */
Quoted 8 lines
Quoted 8 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 852
Quoted 7 lines
drivers/gpu/drm/drm_connector.c +7
-0+ { COLORIMETRY_BT2020_YCC, "BT2020_ycc" }, +/* Colorimetry based on ITU-R BT.2020 */ + { COLORIMETRY_BT2020_CYCC, "BT2020_cycc" }, +/* DP MSA Colorimetry */ + { COLORIMETRY_Y_CBCR_ITU_601, "YCBCR_ITU_601" }, + { COLORIMETRY_Y_CBCR_ITU_709, "YCBCR_ITU_709" }, + { COLORIMETRY_SRGB, "SRGB" },sRGB
Was trying to avoid camelcase, but for these names, I guess we can keep how spec defines them. Will change this.
Quoted 3 lines
Quoted 3 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 854
Quoted 2 lines
drivers/gpu/drm/drm_connector.c +2
-0+ { COLORIMETRY_RGB_WIDE_GAMUT, "RGB Wide Gamut" }, + { COLORIMETRY_SCRGB, "SCRGB" },scRGB?
Will update this.
Quoted 2 lines
Quoted 2 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 855
Quoted 1 line
drivers/gpu/drm/drm_connector.c +1
-0+ { COLORIMETRY_DCI_P3, "DCIP3" },DCI-P3?
Ok, will update
Quoted 2 lines
Quoted 2 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 856
Quoted 1 line
drivers/gpu/drm/drm_connector.c +1
-0+ { COLORIMETRY_CUSTOM_COLOR_PROFILE, "Custom Proflie" },^Typo
Yeah, will rectify this.
Quoted 4 lines
Quoted 4 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 858
Quoted 2 lines
drivers/gpu/drm/drm_connector.c +2
-0+/* FOR HD 720p+, Default Colorimetry is based on ITU-R BT.709 */ + { COLORIMETRY_DEFAULT, "Default: ITU_709" },This enum together with the code below is broken.
Quoted 8 lines
Quoted 3 lines
include/uapi/drm/drm_mode.h +1
-0+ COLORIMETRY_DEFAULT = COLORIMETRY_ITU_709,I would just make it
COLORIMETRY_UNSET= "Unset"."Unset" might work. Though feels a bit strange to me. Other ideas would be "Default", "Automatic", "Undefined" or something along those lines. Ideally it should convey the meaning of "the driver will pick this for you", and for that I'd lean towards "Default" or "Automatic".
Ok, will change this to Default.
Quoted 3 lines
Quoted 3 lines
To set the default colorimetry for all drivers, just make the default value 0 (preferred), or add it to
__drm_atomic_helper_connector_reset().
Ok, will modify this and resend the next version.
Thanks Ville and Maarten for your review and suggestions.
Regards,
Uma Shankar
Quoted 110 lines
Quoted 6 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct
Quoted 6 lines
drivers/gpu/drm/drm_connector.c +2
-0+}; +/** * DOC: standard connector properties * @@ -972,6 +1004,12 @@ int drm_display_info_set_bus_formats(struct
drm_display_info*info,Quoted 11 lines
Quoted 11 lines
drivers/gpu/drm/drm_connector.c +6
-0* can also expose this property to external outputs, in which case they * must support "None", which should be the default (since external screens * have a built-in scaler). +* +* colorspace: +* This property helps select a suitable colorspace based on the sink +* capability. Modern sink devices support wider gamut like BT2020. +* This helps switch to BT2020 mode if the BT2020 encoded video stream +* is being played by the user, same for any other colorspace. */ Quoted 2 lines
Quoted 2 lines
drivers/gpu/drm/drm_connector.c +0
-0int drm_connector_create_standard_properties(struct drm_device*dev) @@ -1020,6 +1058,12 @@ int
drm_connector_create_standard_properties(struct drm_device *dev)Quoted 4 lines
drivers/gpu/drm/drm_connector.c int drm_connector_create_standard_properties(struct drm_device *dev)
Quoted 4 lines
drivers/gpu/drm/drm_connector.c +1
-0return -ENOMEM ; dev->mode_config.non_desktop_property = prop; + prop = drm_property_create_enum(dev, DRM_MODE_PROP_ENUM,"Colorspace",
Quoted 75 lines
Quoted 75 lines
drivers/gpu/drm/drm_connector.c +5
-0+ colorspace, ARRAY_SIZE(colorspace)); +if (!prop) +return -ENOMEM ; + dev->mode_config.colorspace_property = prop; +return 0 ; }(quoted diff) +0
-0
b/include/drm/drm_connector.hindex dd0552c..b7f5373 100644include/drm/drm_connector.h +7
-0@@ -497,6 +497,13 @@ struct drm_connector_state {unsigned int content_protection;/** +* @colorspace: Connector property to request colorspace +* change. This is most commonly used to switch to wider color +* gamuts like BT2020. +*/ +enum encoder_colorimetry colorspace; + +/** * @writeback_job: Writeback job for writeback connectors * * Holds the framebuffer and out-fence for a writeback connector. As diff --git
a/include/drm/drm_mode_config.hb/include/drm/drm_mode_config.hindex d643d26..a6eb0aa 100644include/drm/drm_mode_config.h +6
-0@@ -863,6 +863,12 @@ struct drm_mode_config {uint32_t cursor_width, cursor_height;/** +* @colorspace_property: Connector property to set the suitable +* colorspace supported by the sink. +*/ +struct drm_property *colorspace_property; + +/** * @suspend_state: * * Atomic state when suspended. (quoted diff) +0
-0
b/include/uapi/drm/drm_mode.hindex d3e0fe3..831cc77 100644include/uapi/drm/drm_mode.h +23
-0@@ -210,6 +210,30 @@#define DRM_MODE_CONTENT_PROTECTION_DESIRED 1#define DRM_MODE_CONTENT_PROTECTION_ENABLED 2 +enum encoder_colorimetry { +/* CEA 861 Normal Colorimetry options */ +COLORIMETRY_ITU_601 =0 , +COLORIMETRY_ITU_709 , +/* CEA 861 Extended Colorimetry Options */ +COLORIMETRY_XV_YCC_601 , +COLORIMETRY_XV_YCC_709 , +COLORIMETRY_S_YCC_601 , +COLORIMETRY_ADOBE_YCC_601 , +COLORIMETRY_ADOBE_RGB , +COLORIMETRY_BT2020_RGB , +COLORIMETRY_BT2020_YCC , +COLORIMETRY_BT2020_CYCC , +/* DP MSA Colorimetry Options */ +COLORIMETRY_Y_CBCR_ITU_601 , +COLORIMETRY_Y_CBCR_ITU_709 , +COLORIMETRY_SRGB , +COLORIMETRY_RGB_WIDE_GAMUT , +COLORIMETRY_SCRGB , +COLORIMETRY_DCI_P3 , +COLORIMETRY_CUSTOM_COLOR_PROFILE , +COLORIMETRY_DEFAULT =COLORIMETRY_ITU_709 , }; +struct drm_mode_modeinfo {Quoted 8 lines
include/uapi/drm/drm_mode.h line 239
Quoted 2 lines
include/uapi/drm/drm_mode.h +0
-0__u32 clock;__u16 hdisplay;_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Quoted 3 lines
--
Ville Syrjälä
Intel
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [v2 1/2] drm: Add colorspace property
Quoted 85 lines · Uma
Quoted 74 lines
-----Original Message-----
From: Ville Syrjälä [mailto:[email protected]]
Sent: Friday, November 2, 2018 5:00 PM
To: Maarten Lankhorst <[email protected]>
Cc: Shankar, Uma <[email protected]>; [email protected]; [email protected]; Syrjala, Ville <[email protected]>; Lankhorst, Maarten <[email protected]>; Hans Verkuil <[email protected]>
Subject: Re: [Intel-gfx] [v2 1/2] drm: Add colorspace propertyQuoted 13 lines · Maarten Lankhorst
Op 31-10-18 om 13:05 schreef Uma Shankar:
Quoted 12 lines
This patch adds a colorspace property enabling userspace to switch to various supported colorspaces.
This will help enable BT2020 along with other colorspaces.v2: Addressed Maarten and Ville's review comments. Enhanced the colorspace enum to incorporate both HDMI and DP supported colorspaces. Also, added a default option for colorspace.
Signed-off-by Uma Shankar <[email protected]>--- drivers/gpu/drm/drm_atomic_uapi.c | 4 ++++ drivers/gpu/drm/drm_connector.c | 44+++++++++++++++++++++++++++++++++++++++
Quoted 11 lines
drivers/gpu/drm/drm_atomic_uapi.c static int drm_atomic_connector_set_property(struct
Quoted 11 lines
include/drm/drm_connector.h | 7 +++++++ include/drm/drm_mode_config.h | 6 ++++++ include/uapi/drm/drm_mode.h | 24 +++++++++++++++++++++ 5 files changed, 85 insertions(+)drivers/gpu/drm/drm_atomic_uapi.c +0
-0@@ -721,6 +721,8 @@ static int drm_atomic_connector_set_property(struct
drm_connector*connector,Quoted 9 lines
drivers/gpu/drm/drm_atomic_uapi.c static int drm_atomic_connector_set_property(struct
Quoted 9 lines
drivers/gpu/drm/drm_atomic_uapi.c +2
-0state->picture_aspect_ratio = val; }else if (property == config->content_type_property) { state->content_type = val; + }else if (property == config->colorspace_property) { + state->colorspace = val; }else if (property == connector->scaling_mode_property) { state->scaling_mode = val; }else if (property == connector->content_protection_property) {@@ -795,6 +797,8 @@ static int drm_atomic_connector_set_property(struct
drm_connector*connector,Quoted 7 lines
Quoted 7 lines
drivers/gpu/drm/drm_atomic_uapi.c +2
-0*val = state->picture_aspect_ratio; }else if (property == config->content_type_property) { *val = state->content_type; + }else if (property == config->colorspace_property) { + *val = state->colorspace; }else if (property == connector->scaling_mode_property) { *val = state->scaling_mode;Quoted 8 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct · line 827
Quoted 8 lines
drivers/gpu/drm/drm_atomic_uapi.c +0
-0}else if (property == connector->content_protection_property) {(quoted diff) +0
-0
b/drivers/gpu/drm/drm_connector.cindex aa18b1d..5ad52a0 100644drivers/gpu/drm/drm_connector.c +0
-0@@ -826,6 +826,38 @@ int drm_display_info_set_bus_formats(struct drm_display_info *info, }; DRM_ENUM_NAME_FN(drm_get_content_protection_name,
drm_cp_enum_list)Quoted 10 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 836
Quoted 8 lines
drivers/gpu/drm/drm_connector.c +8
-0+static const struct drm_prop_enum_list colorspace[] = { +/* Standard Definition Colorimetry based on CEA 861 */ + {COLORIMETRY_ITU_601 ,"601" }, + {COLORIMETRY_ITU_709 ,"709" }, +/* Standard Definition Colorimetry based on IEC 61966-2-4 */ + {COLORIMETRY_XV_YCC_601 ,"601" }, +/* High Definition Colorimetry based on IEC 61966-2-4 */ + {COLORIMETRY_XV_YCC_709 ,"709" },2 definitions that share the same name?
All in all, I think the enum strings need to be more descriptive and self-Quoted 2 lines
consistent.
+1Sure, will modify this.
Quoted 7 lines
Quoted 4 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 840
Quoted 4 lines
drivers/gpu/drm/drm_connector.c +4
-0+/* Colorimetry based on IEC 61966-2-1/Amendment 1 */ + { COLORIMETRY_S_YCC_601, "s601" }, +/* Colorimetry based on IEC 61966-2-5 [33] */ + { COLORIMETRY_ADOBE_YCC_601, "adobe601" },Hans (cc:d) recetly noted that these things aren't called Adobe<something> anymore in the CTA-861 spec. There is some new name for them, which I now forget.
Quoted 5 lines
EC2 EC1 EC0 Extended Colorimetry
0 1 1 AdobeYCC601
This is the bit format mentioned in CEA861.F while defining the AVI infoframe, so looks like they are still keeping it that way. Not sure if its updated as part of any latest spec update.
New names is opRGB and opYCC601 according to the notice on the first page of CTA-861-G [1]
Updated CTA-861-E/F/G can be found at https://standards.cta.tech/kwspub/published_docs/
[1] https://standards.cta.tech/kwspub/published_docs/CTA-861-G_FINAL_revised_2017.pdf
Quoted 159 lines
Quoted 14 lines
Quoted 14 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 852
Quoted 13 lines
drivers/gpu/drm/drm_connector.c +12
-0+/* Colorimetry based on IEC 61966-2-5 */ + { COLORIMETRY_ADOBE_RGB, "adobe_rgb" }, +/* Colorimetry based on ITU-R BT.2020 */ + { COLORIMETRY_BT2020_RGB, "BT2020_rgb" }, +/* Colorimetry based on ITU-R BT.2020 */ + { COLORIMETRY_BT2020_YCC, "BT2020_ycc" }, +/* Colorimetry based on ITU-R BT.2020 */ + { COLORIMETRY_BT2020_CYCC, "BT2020_cycc" }, +/* DP MSA Colorimetry */ + { COLORIMETRY_Y_CBCR_ITU_601, "YCBCR_ITU_601" }, + { COLORIMETRY_Y_CBCR_ITU_709, "YCBCR_ITU_709" }, + { COLORIMETRY_SRGB, "SRGB" },sRGB
Was trying to avoid camelcase, but for these names, I guess we can keep how spec defines them. Will change this.
Quoted 3 lines
Quoted 3 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 854
Quoted 2 lines
drivers/gpu/drm/drm_connector.c +2
-0+ { COLORIMETRY_RGB_WIDE_GAMUT, "RGB Wide Gamut" }, + { COLORIMETRY_SCRGB, "SCRGB" },scRGB?
Will update this.
Quoted 2 lines
Quoted 2 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 855
Quoted 1 line
drivers/gpu/drm/drm_connector.c +1
-0+ { COLORIMETRY_DCI_P3, "DCIP3" },DCI-P3?
Ok, will update
Quoted 2 lines
Quoted 2 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 856
Quoted 1 line
drivers/gpu/drm/drm_connector.c +1
-0+ { COLORIMETRY_CUSTOM_COLOR_PROFILE, "Custom Proflie" },^Typo
Yeah, will rectify this.
Quoted 11 lines
Quoted 7 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 858
Quoted 2 lines
drivers/gpu/drm/drm_connector.c +2
-0+/* FOR HD 720p+, Default Colorimetry is based on ITU-R BT.709 */ + { COLORIMETRY_DEFAULT, "Default: ITU_709" },This enum together with the code below is broken.
include/uapi/drm/drm_mode.h +1
-0+ COLORIMETRY_DEFAULT = COLORIMETRY_ITU_709,I would just make it
COLORIMETRY_UNSET= "Unset"."Unset" might work. Though feels a bit strange to me. Other ideas would be "Default", "Automatic", "Undefined" or something along those lines. Ideally it should convey the meaning of "the driver will pick this for you", and for that I'd lean towards "Default" or "Automatic".
Ok, will change this to Default.
Quoted 2 lines
Quoted 2 lines
To set the default colorimetry for all drivers, just make the default value 0 (preferred), or add it to
__drm_atomic_helper_connector_reset().Ok, will modify this and resend the next version.
Thanks Ville and Maarten for your review and suggestions.
Regards,
Uma ShankarQuoted 108 lines
Quoted 6 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct
Quoted 6 lines
drivers/gpu/drm/drm_connector.c +2
-0+}; +/** * DOC: standard connector properties * @@ -972,6 +1004,12 @@ int drm_display_info_set_bus_formats(struct
drm_display_info*info,Quoted 11 lines
Quoted 11 lines
drivers/gpu/drm/drm_connector.c +6
-0* can also expose this property to external outputs, in which case they * must support "None", which should be the default (since external screens * have a built-in scaler). +* +* colorspace: +* This property helps select a suitable colorspace based on the sink +* capability. Modern sink devices support wider gamut like BT2020. +* This helps switch to BT2020 mode if the BT2020 encoded video stream +* is being played by the user, same for any other colorspace. */ Quoted 2 lines
Quoted 2 lines
drivers/gpu/drm/drm_connector.c +0
-0int drm_connector_create_standard_properties(struct drm_device*dev) @@ -1020,6 +1058,12 @@ int
drm_connector_create_standard_properties(struct drm_device *dev)Quoted 4 lines
drivers/gpu/drm/drm_connector.c int drm_connector_create_standard_properties(struct drm_device *dev)
Quoted 4 lines
drivers/gpu/drm/drm_connector.c +1
-0return -ENOMEM ; dev->mode_config.non_desktop_property = prop; + prop = drm_property_create_enum(dev, DRM_MODE_PROP_ENUM,"Colorspace",
Quoted 82 lines
Quoted 67 lines
drivers/gpu/drm/drm_connector.c +5
-0+ colorspace, ARRAY_SIZE(colorspace)); +if (!prop) +return -ENOMEM ; + dev->mode_config.colorspace_property = prop; +return 0 ; }(quoted diff) +0
-0
b/include/drm/drm_connector.hindex dd0552c..b7f5373 100644include/drm/drm_connector.h +7
-0@@ -497,6 +497,13 @@ struct drm_connector_state {unsigned int content_protection;/** +* @colorspace: Connector property to request colorspace +* change. This is most commonly used to switch to wider color +* gamuts like BT2020. +*/ +enum encoder_colorimetry colorspace; + +/** * @writeback_job: Writeback job for writeback connectors * * Holds the framebuffer and out-fence for a writeback connector. As diff --git
a/include/drm/drm_mode_config.hb/include/drm/drm_mode_config.hindex d643d26..a6eb0aa 100644include/drm/drm_mode_config.h +6
-0@@ -863,6 +863,12 @@ struct drm_mode_config {uint32_t cursor_width, cursor_height;/** +* @colorspace_property: Connector property to set the suitable +* colorspace supported by the sink. +*/ +struct drm_property *colorspace_property; + +/** * @suspend_state: * * Atomic state when suspended. (quoted diff) +0
-0
b/include/uapi/drm/drm_mode.hindex d3e0fe3..831cc77 100644include/uapi/drm/drm_mode.h +16
-0@@ -210,6 +210,30 @@#define DRM_MODE_CONTENT_PROTECTION_DESIRED 1#define DRM_MODE_CONTENT_PROTECTION_ENABLED 2 +enum encoder_colorimetry { +/* CEA 861 Normal Colorimetry options */ +COLORIMETRY_ITU_601 =0 , +COLORIMETRY_ITU_709 , +/* CEA 861 Extended Colorimetry Options */ +COLORIMETRY_XV_YCC_601 , +COLORIMETRY_XV_YCC_709 , +COLORIMETRY_S_YCC_601 , +COLORIMETRY_ADOBE_YCC_601 , +COLORIMETRY_ADOBE_RGB , +COLORIMETRY_BT2020_RGB , +COLORIMETRY_BT2020_YCC , +COLORIMETRY_BT2020_CYCC , +/* DP MSA Colorimetry Options */ +COLORIMETRY_Y_CBCR_ITU_601 , +COLORIMETRY_Y_CBCR_ITU_709 ,include/uapi/drm/drm_mode.h line 238
Quoted 10 lines
include/uapi/drm/drm_mode.h +7
-0+ COLORIMETRY_SRGB, +COLORIMETRY_RGB_WIDE_GAMUT , +COLORIMETRY_SCRGB , +COLORIMETRY_DCI_P3 , +COLORIMETRY_CUSTOM_COLOR_PROFILE , + COLORIMETRY_DEFAULT = COLORIMETRY_ITU_709, }; +struct drm_mode_modeinfo {__u32 clock;__u16 hdisplay;_______________________________________________
dri-devel mailing list
[email protected]
https://nam02.safelinks.protection.outlook.com/?url=https%3A%2F%2Flists.freedesktop.org%2Fmailman%2Flistinfo%2Fdri-devel&data=02%7C01%7C%7C2e75af29da3342d27bac08d640cd62cd%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636767648196557839&sdata=V2VlqgzetFVCtiXJE8yt%2Fl2uPhC8M7498peHNubR4Fw%3D&reserved=0
Quoted 7 lines
Quoted 3 lines
--
Ville Syrjälä
Intel_______________________________________________
dri-devel mailing list
[email protected]
https://nam02.safelinks.protection.outlook.com/?url=https%3A%2F%2Flists.freedesktop.org%2Fmailman%2Flistinfo%2Fdri-devel&data=02%7C01%7C%7C2e75af29da3342d27bac08d640cd62cd%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636767648196557839&sdata=V2VlqgzetFVCtiXJE8yt%2Fl2uPhC8M7498peHNubR4Fw%3D&reserved=0
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [Intel-gfx] [v2 1/2] drm: Add colorspace property
Quoted 92 lines · Jonas Karlman
Quoted 85 lines · Uma
Quoted 74 lines
-----Original Message-----
From: Ville Syrjälä [mailto:[email protected]]
Sent: Friday, November 2, 2018 5:00 PM
To: Maarten Lankhorst <[email protected]>
Cc: Shankar, Uma <[email protected]>; [email protected]; [email protected]; Syrjala, Ville <[email protected]>; Lankhorst, Maarten <[email protected]>; Hans Verkuil <[email protected]>
Subject: Re: [Intel-gfx] [v2 1/2] drm: Add colorspace propertyQuoted 13 lines · Maarten Lankhorst
Op 31-10-18 om 13:05 schreef Uma Shankar:
Quoted 12 lines
This patch adds a colorspace property enabling userspace to switch to various supported colorspaces.
This will help enable BT2020 along with other colorspaces.v2: Addressed Maarten and Ville's review comments. Enhanced the colorspace enum to incorporate both HDMI and DP supported colorspaces. Also, added a default option for colorspace.
Signed-off-by Uma Shankar <[email protected]>--- drivers/gpu/drm/drm_atomic_uapi.c | 4 ++++ drivers/gpu/drm/drm_connector.c | 44+++++++++++++++++++++++++++++++++++++++
Quoted 11 lines
drivers/gpu/drm/drm_atomic_uapi.c static int drm_atomic_connector_set_property(struct
Quoted 11 lines
include/drm/drm_connector.h | 7 +++++++ include/drm/drm_mode_config.h | 6 ++++++ include/uapi/drm/drm_mode.h | 24 +++++++++++++++++++++ 5 files changed, 85 insertions(+)drivers/gpu/drm/drm_atomic_uapi.c +0
-0@@ -721,6 +721,8 @@ static int drm_atomic_connector_set_property(struct
drm_connector*connector,Quoted 9 lines
drivers/gpu/drm/drm_atomic_uapi.c static int drm_atomic_connector_set_property(struct
Quoted 9 lines
drivers/gpu/drm/drm_atomic_uapi.c +2
-0state->picture_aspect_ratio = val; }else if (property == config->content_type_property) { state->content_type = val; + }else if (property == config->colorspace_property) { + state->colorspace = val; }else if (property == connector->scaling_mode_property) { state->scaling_mode = val; }else if (property == connector->content_protection_property) {@@ -795,6 +797,8 @@ static int drm_atomic_connector_set_property(struct
drm_connector*connector,Quoted 7 lines
Quoted 7 lines
drivers/gpu/drm/drm_atomic_uapi.c +2
-0*val = state->picture_aspect_ratio; }else if (property == config->content_type_property) { *val = state->content_type; + }else if (property == config->colorspace_property) { + *val = state->colorspace; }else if (property == connector->scaling_mode_property) { *val = state->scaling_mode;Quoted 8 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct · line 827
Quoted 8 lines
drivers/gpu/drm/drm_atomic_uapi.c +0
-0}else if (property == connector->content_protection_property) {(quoted diff) +0
-0
b/drivers/gpu/drm/drm_connector.cindex aa18b1d..5ad52a0 100644drivers/gpu/drm/drm_connector.c +0
-0@@ -826,6 +826,38 @@ int drm_display_info_set_bus_formats(struct drm_display_info *info, }; DRM_ENUM_NAME_FN(drm_get_content_protection_name,
drm_cp_enum_list)Quoted 10 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 836
Quoted 8 lines
drivers/gpu/drm/drm_connector.c +8
-0+static const struct drm_prop_enum_list colorspace[] = { +/* Standard Definition Colorimetry based on CEA 861 */ + {COLORIMETRY_ITU_601 ,"601" }, + {COLORIMETRY_ITU_709 ,"709" }, +/* Standard Definition Colorimetry based on IEC 61966-2-4 */ + {COLORIMETRY_XV_YCC_601 ,"601" }, +/* High Definition Colorimetry based on IEC 61966-2-4 */ + {COLORIMETRY_XV_YCC_709 ,"709" },2 definitions that share the same name?
All in all, I think the enum strings need to be more descriptive and self-Quoted 2 lines
consistent.
+1Sure, will modify this.
Quoted 7 lines
Quoted 4 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 840
Quoted 4 lines
drivers/gpu/drm/drm_connector.c +4
-0+/* Colorimetry based on IEC 61966-2-1/Amendment 1 */ + { COLORIMETRY_S_YCC_601, "s601" }, +/* Colorimetry based on IEC 61966-2-5 [33] */ + { COLORIMETRY_ADOBE_YCC_601, "adobe601" },Hans (cc:d) recetly noted that these things aren't called Adobe<something> anymore in the CTA-861 spec. There is some new name for them, which I now forget.
Quoted 5 lines
EC2 EC1 EC0 Extended Colorimetry
0 1 1 AdobeYCC601
This is the bit format mentioned in CEA861.F while defining the AVI infoframe, so looks like they are still keeping it that way. Not sure if its updated as part of any latest spec update.
Quoted 5 lines
New names is opRGB and opYCC601 according to the notice on the first page of CTA-861-G [1]
Updated CTA-861-E/F/G can be found at https://standards.cta.tech/kwspub/published_docs/
[1] https://standards.cta.tech/kwspub/published_docs/CTA-861-G_FINAL_revised_2017.pdf
Correct. The names were updated since Adobe complained to the CTA about trademark issues. And in all fairness, it makes sense to refer to the official international standard name instead of a company standard, even though they are effectively identical.
Basically, just avoid the name 'Adobe' :-)
Regards,
Hans
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [v2 1/2] drm: Add colorspace property
In reply to Uma ShankarRegards
Shashank
Quoted 83 lines · Uma Shankar
This patch adds a colorspace property enabling userspace to switch to various supported colorspaces. This will help enable BT2020 along with other colorspaces.
v2: Addressed Maarten and Ville's review comments. Enhanced the colorspace enum to incorporate both HDMI and DP supported colorspaces. Also, added a default option for colorspace.
Signed-off-by Uma Shankar <[email protected]>--- drivers/gpu/drm/drm_atomic_uapi.c | 4 ++++ drivers/gpu/drm/drm_connector.c | 44 +++++++++++++++++++++++++++++++++++++++ include/drm/drm_connector.h | 7 +++++++ include/drm/drm_mode_config.h | 6 ++++++ include/uapi/drm/drm_mode.h | 24 +++++++++++++++++++++ 5 files changed, 85 insertions(+)drivers/gpu/drm/drm_atomic_uapi.c +4
-0@@ -721,6 +721,8 @@ static int drm_atomic_connector_set_property(struct drm_connector *connector, state->picture_aspect_ratio = val; }else if (property == config->content_type_property) { state->content_type = val; + }else if (property == config->colorspace_property) { + state->colorspace = val; }else if (property == connector->scaling_mode_property) { state->scaling_mode = val; }else if (property == connector->content_protection_property) {@@ -795,6 +797,8 @@ static int drm_atomic_connector_set_property(struct drm_connector *connector, *val = state->picture_aspect_ratio; }else if (property == config->content_type_property) { *val = state->content_type; + }else if (property == config->colorspace_property) { + *val = state->colorspace; }else if (property == connector->scaling_mode_property) { *val = state->scaling_mode; }else if (property == connector->content_protection_property) {drivers/gpu/drm/drm_connector.c +32
-0@@ -826,6 +826,38 @@ int drm_display_info_set_bus_formats(struct drm_display_info *info, }; DRM_ENUM_NAME_FN(drm_get_content_protection_name, drm_cp_enum_list) +static const struct drm_prop_enum_list colorspace[] = { +/* Standard Definition Colorimetry based on CEA 861 */ + {COLORIMETRY_ITU_601 ,"601" }, + {COLORIMETRY_ITU_709 ,"709" }, +/* Standard Definition Colorimetry based on IEC 61966-2-4 */ + {COLORIMETRY_XV_YCC_601 ,"601" }, +/* High Definition Colorimetry based on IEC 61966-2-4 */ + {COLORIMETRY_XV_YCC_709 ,"709" }, +/* Colorimetry based on IEC 61966-2-1/Amendment 1 */ + {COLORIMETRY_S_YCC_601 ,"s601" }, +/* Colorimetry based on IEC 61966-2-5 [33] */ + {COLORIMETRY_ADOBE_YCC_601 ,"adobe601" }, +/* Colorimetry based on IEC 61966-2-5 */ + {COLORIMETRY_ADOBE_RGB ,"adobe_rgb" }, +/* Colorimetry based on ITU-R BT.2020 */ + {COLORIMETRY_BT2020_RGB ,"BT2020_rgb" }, +/* Colorimetry based on ITU-R BT.2020 */ + {COLORIMETRY_BT2020_YCC ,"BT2020_ycc" }, +/* Colorimetry based on ITU-R BT.2020 */ + {COLORIMETRY_BT2020_CYCC ,"BT2020_cycc" }, +/* DP MSA Colorimetry */ + {COLORIMETRY_Y_CBCR_ITU_601 ,"YCBCR_ITU_601" }, + {COLORIMETRY_Y_CBCR_ITU_709 ,"YCBCR_ITU_709" }, + {COLORIMETRY_SRGB ,"SRGB" }, + {COLORIMETRY_RGB_WIDE_GAMUT ,"RGB Wide Gamut" }, + {COLORIMETRY_SCRGB ,"SCRGB" }, + {COLORIMETRY_DCI_P3 ,"DCIP3" }, + {COLORIMETRY_CUSTOM_COLOR_PROFILE ,"Custom Proflie" }, +/* FOR HD 720p+, Default Colorimetry is based on ITU-R BT.709 */ + {COLORIMETRY_DEFAULT ,"Default: ITU_709" }, +}; +/** * DOC: standard connector properties *
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 1012
Quoted 9 lines
drivers/gpu/drm/drm_connector.c +6
-0@@ -972,6 +1004,12 @@ int drm_display_info_set_bus_formats(struct drm_display_info *info,* can also expose this property to external outputs, in which case they * must support "None", which should be the default (since external screens * have a built-in scaler). +* +* colorspace: +* This property helps select a suitable colorspace based on the sink +* capability. Modern sink devices support wider gamut like BT2020. +* This helps switch to BT2020 mode if the BT2020 encoded video stream +* is being played by the user, same for any other colorspace.
As commented on the previous patch, we might have to consider the HW capability while doing this.
Quoted 21 lines
drivers/gpu/drm/drm_connector.c +6
-0*/ int drm_connector_create_standard_properties (struct drm_device *dev)@@ -1020,6 +1058,12 @@ int drm_connector_create_standard_properties(struct drm_device *dev)return -ENOMEM ; dev->mode_config.non_desktop_property = prop; + prop =drm_property_create_enum (dev,DRM_MODE_PROP_ENUM ,"Colorspace" , + colorspace,ARRAY_SIZE (colorspace)); +if (!prop) +return -ENOMEM ; + dev->mode_config.colorspace_property = prop; +return 0 ; }include/drm/drm_connector.h +0
-0
include/drm/drm_connector.h struct drm_connector_state { · line 504
Quoted 8 lines
include/drm/drm_connector.h +5
-0@@ -497,6 +497,13 @@ struct drm_connector_state {unsigned int content_protection;/** +* @colorspace: Connector property to request colorspace +* change. This is most commonly used to switch to wider color +* gamuts like BT2020. +*/ +enum encoder_colorimetry colorspace;
A connector state property with enum name encoder_colorimetry is a bit confusing, but I might be nitpicking ;-)
Quoted 48 lines
include/drm/drm_connector.h +2
-0+ +/** * @writeback_job: Writeback job for writeback connectors * * Holds the framebuffer and out-fence for a writeback connector. As include/drm/drm_mode_config.h +6
-0@@ -863,6 +863,12 @@ struct drm_mode_config {uint32_t cursor_width, cursor_height;/** +* @colorspace_property: Connector property to set the suitable +* colorspace supported by the sink. +*/ +struct drm_property *colorspace_property; + +/** * @suspend_state: * * Atomic state when suspended. include/uapi/drm/drm_mode.h +17
-0@@ -210,6 +210,30 @@#define DRM_MODE_CONTENT_PROTECTION_DESIRED 1#define DRM_MODE_CONTENT_PROTECTION_ENABLED 2 +enum encoder_colorimetry { +/* CEA 861 Normal Colorimetry options */ +COLORIMETRY_ITU_601 =0 , +COLORIMETRY_ITU_709 , +/* CEA 861 Extended Colorimetry Options */ +COLORIMETRY_XV_YCC_601 , +COLORIMETRY_XV_YCC_709 , +COLORIMETRY_S_YCC_601 , +COLORIMETRY_ADOBE_YCC_601 , +COLORIMETRY_ADOBE_RGB , +COLORIMETRY_BT2020_RGB , +COLORIMETRY_BT2020_YCC , +COLORIMETRY_BT2020_CYCC , +/* DP MSA Colorimetry Options */ +COLORIMETRY_Y_CBCR_ITU_601 , +COLORIMETRY_Y_CBCR_ITU_709 , +COLORIMETRY_SRGB ,
include/uapi/drm/drm_mode.h line 239
Quoted 10 lines
include/uapi/drm/drm_mode.h +7
-0+ COLORIMETRY_RGB_WIDE_GAMUT, +COLORIMETRY_SCRGB , +COLORIMETRY_DCI_P3 , +COLORIMETRY_CUSTOM_COLOR_PROFILE , + COLORIMETRY_DEFAULT = COLORIMETRY_ITU_709, +}; +struct drm_mode_modeinfo {__u32 clock;__u16 hdisplay;
- Shashank
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [v2 1/2] drm: Add colorspace property
In reply to Uma ShankarHi Uma,
Quoted 83 lines · Uma Shankar
This patch adds a colorspace property enabling userspace to switch to various supported colorspaces. This will help enable BT2020 along with other colorspaces.
v2: Addressed Maarten and Ville's review comments. Enhanced the colorspace enum to incorporate both HDMI and DP supported colorspaces. Also, added a default option for colorspace.
Signed-off-by Uma Shankar <uma.shankar at intel.com>---
drivers/gpu/drm/drm_atomic_uapi.c | 4 ++++ drivers/gpu/drm/drm_connector.c | 44 +++++++++++++++++++++++++++++++++++++++ include/drm/drm_connector.h | 7 +++++++ include/drm/drm_mode_config.h | 6 ++++++ include/uapi/drm/drm_mode.h | 24 +++++++++++++++++++++ 5 files changed, 85 insertions(+)drivers/gpu/drm/drm_atomic_uapi.c +4
-0@@ -721,6 +721,8 @@ static int drm_atomic_connector_set_property(struct drm_connector *connector, state->picture_aspect_ratio = val; }else if (property == config->content_type_property) { state->content_type = val; + }else if (property == config->colorspace_property) { + state->colorspace = val; }else if (property == connector->scaling_mode_property) { state->scaling_mode = val; }else if (property == connector->content_protection_property) {@@ -795,6 +797,8 @@ static int drm_atomic_connector_set_property(struct drm_connector *connector, *val = state->picture_aspect_ratio; }else if (property == config->content_type_property) { *val = state->content_type; + }else if (property == config->colorspace_property) { + *val = state->colorspace; }else if (property == connector->scaling_mode_property) { *val = state->scaling_mode; }else if (property == connector->content_protection_property) {drivers/gpu/drm/drm_connector.c +32
-0@@ -826,6 +826,38 @@ int drm_display_info_set_bus_formats(struct drm_display_info *info, }; DRM_ENUM_NAME_FN(drm_get_content_protection_name, drm_cp_enum_list) +static const struct drm_prop_enum_list colorspace[] = { +/* Standard Definition Colorimetry based on CEA 861 */ + {COLORIMETRY_ITU_601 ,"601" }, + {COLORIMETRY_ITU_709 ,"709" }, +/* Standard Definition Colorimetry based on IEC 61966-2-4 */ + {COLORIMETRY_XV_YCC_601 ,"601" }, +/* High Definition Colorimetry based on IEC 61966-2-4 */ + {COLORIMETRY_XV_YCC_709 ,"709" }, +/* Colorimetry based on IEC 61966-2-1/Amendment 1 */ + {COLORIMETRY_S_YCC_601 ,"s601" }, +/* Colorimetry based on IEC 61966-2-5 [33] */ + {COLORIMETRY_ADOBE_YCC_601 ,"adobe601" }, +/* Colorimetry based on IEC 61966-2-5 */ + {COLORIMETRY_ADOBE_RGB ,"adobe_rgb" }, +/* Colorimetry based on ITU-R BT.2020 */ + {COLORIMETRY_BT2020_RGB ,"BT2020_rgb" }, +/* Colorimetry based on ITU-R BT.2020 */ + {COLORIMETRY_BT2020_YCC ,"BT2020_ycc" }, +/* Colorimetry based on ITU-R BT.2020 */ + {COLORIMETRY_BT2020_CYCC ,"BT2020_cycc" }, +/* DP MSA Colorimetry */ + {COLORIMETRY_Y_CBCR_ITU_601 ,"YCBCR_ITU_601" }, + {COLORIMETRY_Y_CBCR_ITU_709 ,"YCBCR_ITU_709" }, + {COLORIMETRY_SRGB ,"SRGB" }, + {COLORIMETRY_RGB_WIDE_GAMUT ,"RGB Wide Gamut" }, + {COLORIMETRY_SCRGB ,"SCRGB" }, + {COLORIMETRY_DCI_P3 ,"DCIP3" }, + {COLORIMETRY_CUSTOM_COLOR_PROFILE ,"Custom Proflie" }, +/* FOR HD 720p+, Default Colorimetry is based on ITU-R BT.709 */ + {COLORIMETRY_DEFAULT ,"Default: ITU_709" }, +}; +/** * DOC: standard connector properties *
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 1008
Quoted 5 lines
drivers/gpu/drm/drm_connector.c +2
-0@@ -972,6 +1004,12 @@ int drm_display_info_set_bus_formats(struct drm_display_info *info,* can also expose this property to external outputs, in which case they * must support "None", which should be the default (since external screens * have a built-in scaler). +* +* colorspace:
Is it "colorspace" or "Colorspace"? The code says capital-C, the doc (and whatever little convention there is) says lower-case.
drivers/gpu/drm/drm_connector.c int drm_connector_create_standard_properties(struct drm_device *dev) · line 1062
Quoted 13 lines
drivers/gpu/drm/drm_connector.c +6
-0+* This property helps select a suitable colorspace based on the sink +* capability. Modern sink devices support wider gamut like BT2020. +* This helps switch to BT2020 mode if the BT2020 encoded video stream +* is being played by the user, same for any other colorspace. */ int drm_connector_create_standard_properties (struct drm_device *dev)@@ -1020,6 +1058,12 @@ int drm_connector_create_standard_properties(struct drm_device *dev)return -ENOMEM ; dev->mode_config.non_desktop_property = prop; + prop =drm_property_create_enum (dev,DRM_MODE_PROP_ENUM ,"Colorspace" , + colorspace,ARRAY_SIZE (colorspace));
Similar to what others have said: I'm not sure it's a great idea to expose the full set by default. At a minimum, actually applying this property requires some control over the HDMI/DP transmitter doesn't it? And I believe they vary in capabilities?
Further, I'd expect some of them to require more extensive changes further through the pipe (e.g. scRGB), though I admit I don't know much about how Sinks handle this stuff.
Do you have a subset which you have a real user and use-case for which we might settle on before throwing them all in and making it UAPI?
Cheers,
-Brian
Quoted 81 lines
drivers/gpu/drm/drm_connector.c +4
-0+if (!prop) +return -ENOMEM ; + dev->mode_config.colorspace_property = prop; +return 0 ; }include/drm/drm_connector.h +7
-0@@ -497,6 +497,13 @@ struct drm_connector_state {unsigned int content_protection;/** +* @colorspace: Connector property to request colorspace +* change. This is most commonly used to switch to wider color +* gamuts like BT2020. +*/ +enum encoder_colorimetry colorspace; + +/** * @writeback_job: Writeback job for writeback connectors * * Holds the framebuffer and out-fence for a writeback connector. As include/drm/drm_mode_config.h +6
-0@@ -863,6 +863,12 @@ struct drm_mode_config {uint32_t cursor_width, cursor_height;/** +* @colorspace_property: Connector property to set the suitable +* colorspace supported by the sink. +*/ +struct drm_property *colorspace_property; + +/** * @suspend_state: * * Atomic state when suspended. include/uapi/drm/drm_mode.h +24
-0@@ -210,6 +210,30 @@#define DRM_MODE_CONTENT_PROTECTION_DESIRED 1#define DRM_MODE_CONTENT_PROTECTION_ENABLED 2 +enum encoder_colorimetry { +/* CEA 861 Normal Colorimetry options */ +COLORIMETRY_ITU_601 =0 , +COLORIMETRY_ITU_709 , +/* CEA 861 Extended Colorimetry Options */ +COLORIMETRY_XV_YCC_601 , +COLORIMETRY_XV_YCC_709 , +COLORIMETRY_S_YCC_601 , +COLORIMETRY_ADOBE_YCC_601 , +COLORIMETRY_ADOBE_RGB , +COLORIMETRY_BT2020_RGB , +COLORIMETRY_BT2020_YCC , +COLORIMETRY_BT2020_CYCC , +/* DP MSA Colorimetry Options */ +COLORIMETRY_Y_CBCR_ITU_601 , +COLORIMETRY_Y_CBCR_ITU_709 , +COLORIMETRY_SRGB , +COLORIMETRY_RGB_WIDE_GAMUT , +COLORIMETRY_SCRGB , +COLORIMETRY_DCI_P3 , +COLORIMETRY_CUSTOM_COLOR_PROFILE , +COLORIMETRY_DEFAULT =COLORIMETRY_ITU_709 , +}; +struct drm_mode_modeinfo {__u32 clock;__u16 hdisplay;Signature · 1 line
1.9.1
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
RE: [v2 1/2] drm: Add colorspace property
Quoted 102 lines
-----Original Message-----
From: Brian Starkey [mailto:[email protected]]
Sent: Tuesday, November 20, 2018 9:06 PM
To: Shankar, Uma <[email protected]>; Syrjala, Ville <[email protected]>; Lankhorst, Maarten <[email protected]>; [email protected]; [email protected]
Cc: nd <[email protected]>
Subject: Re: [v2 1/2] drm: Add colorspace propertyHi Uma,
Quoted 4 lines · Uma Shankar
This patch adds a colorspace property enabling userspace to switch to various supported colorspaces.
This will help enable BT2020 along with other colorspaces.Quoted 8 lines
v2: Addressed Maarten and Ville's review comments. Enhanced the colorspace enum to incorporate both HDMI and DP supported colorspaces. Also, added a default option for colorspace.
Signed-off-by Uma Shankar <uma.shankar at intel.com>---
drivers/gpu/drm/drm_atomic_uapi.c| 4 ++++drivers/gpu/drm/drm_connector.c| 44+++++++++++++++++++++++++++++++++++++++
drivers/gpu/drm/drm_atomic_uapi.c static int drm_atomic_connector_set_property(struct
Quoted 11 lines
include/drm/drm_connector.h | 7 +++++++ include/drm/drm_mode_config.h | 6 ++++++ include/uapi/drm/drm_mode.h | 24 +++++++++++++++++++++ 5 files changed, 85 insertions(+)drivers/gpu/drm/drm_atomic_uapi.c +0
-0@@ -721,6 +721,8 @@ static int drm_atomic_connector_set_property(struct
drm_connector*connector,drivers/gpu/drm/drm_atomic_uapi.c static int drm_atomic_connector_set_property(struct drm_connector *connector,
Quoted 9 lines
drivers/gpu/drm/drm_atomic_uapi.c +2
-1state->picture_aspect_ratio = val; }else if (property == config->content_type_property) { state->content_type = val; + }else if (property == config->colorspace_property) { + state->colorspace = val; }else if (property == connector->scaling_mode_property) { state->scaling_mode = val; } else if (property == connector->content_protection_property) { @@ -795,6 +797,8 @@ static int drm_atomic_connector_set_property(struct
drm_connector*connector,Quoted 13 lines
*val = state->picture_aspect_ratio; } else if (property == config->content_type_property) { *val = state->content_type;drivers/gpu/drm/drm_atomic_uapi.c +2
-0+ }else if (property == config->colorspace_property) { + *val = state->colorspace;} else if (property == connector->scaling_mode_property) { *val = state->scaling_mode; } else if (property == connector->content_protection_property) { diff--git
a/drivers/gpu/drm/drm_connector.cb/drivers/gpu/drm/drm_connector.cindex aa18b1d..5ad52a0 100644drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct · line 827
Quoted 2 lines
drivers/gpu/drm/drm_connector.c +0
-0@@ -826,6 +826,38 @@ int drm_display_info_set_bus_formats(struct drm_display_info *info, }; DRM_ENUM_NAME_FN(drm_get_content_protection_name,
drm_cp_enum_list)drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct
Quoted 36 lines
drivers/gpu/drm/drm_connector.c +31
-0+static const struct drm_prop_enum_list colorspace[] = { +/* Standard Definition Colorimetry based on CEA 861 */ + {COLORIMETRY_ITU_601 ,"601" }, + {COLORIMETRY_ITU_709 ,"709" }, +/* Standard Definition Colorimetry based on IEC 61966-2-4 */ + {COLORIMETRY_XV_YCC_601 ,"601" }, +/* High Definition Colorimetry based on IEC 61966-2-4 */ + {COLORIMETRY_XV_YCC_709 ,"709" }, +/* Colorimetry based on IEC 61966-2-1/Amendment 1 */ + {COLORIMETRY_S_YCC_601 ,"s601" }, +/* Colorimetry based on IEC 61966-2-5 [33] */ + {COLORIMETRY_ADOBE_YCC_601 ,"adobe601" }, +/* Colorimetry based on IEC 61966-2-5 */ + {COLORIMETRY_ADOBE_RGB ,"adobe_rgb" }, +/* Colorimetry based on ITU-R BT.2020 */ + {COLORIMETRY_BT2020_RGB ,"BT2020_rgb" }, +/* Colorimetry based on ITU-R BT.2020 */ + {COLORIMETRY_BT2020_YCC ,"BT2020_ycc" }, +/* Colorimetry based on ITU-R BT.2020 */ + {COLORIMETRY_BT2020_CYCC ,"BT2020_cycc" }, +/* DP MSA Colorimetry */ + {COLORIMETRY_Y_CBCR_ITU_601 ,"YCBCR_ITU_601" }, + {COLORIMETRY_Y_CBCR_ITU_709 ,"YCBCR_ITU_709" }, + {COLORIMETRY_SRGB ,"SRGB" }, + {COLORIMETRY_RGB_WIDE_GAMUT ,"RGB Wide Gamut" }, + {COLORIMETRY_SCRGB ,"SCRGB" }, + {COLORIMETRY_DCI_P3 ,"DCIP3" }, + {COLORIMETRY_CUSTOM_COLOR_PROFILE ,"Custom Proflie" }, +/* FOR HD 720p+, Default Colorimetry is based on ITU-R BT.709 */ + {COLORIMETRY_DEFAULT ,"Default: ITU_709" }, }; +/** * DOC: standard connector properties * @@ -972,6 +1004,12 @@ int drm_display_info_set_bus_formats(struct
drm_display_info*info,
Quoted 8 lines
drivers/gpu/drm/drm_connector.c int drm_display_info_set_bus_formats(struct drm_display_info *info, · line 1008
Quoted 5 lines
drivers/gpu/drm/drm_connector.c +2
-0* can also expose this property to external outputs, in which case they * must support "None", which should be the default (since external screens * have a built-in scaler). +* +* colorspace: Is it "colorspace" or "Colorspace"? The code says capital-C, the doc (and whatever little convention there is) says lower-case.
I will update this. It should be "Colorspace".
Quoted 21 lines
drivers/gpu/drm/drm_connector.c int
Quoted 8 lines
drivers/gpu/drm/drm_connector.c +4
-0+* This property helps select a suitable colorspace based on the sink +* capability. Modern sink devices support wider gamut like BT2020. +* This helps switch to BT2020 mode if the BT2020 encoded video stream +* is being played by the user, same for any other colorspace. */ int drm_connector_create_standard_properties (struct drm_device *dev)@@ -1020,6 +1058,12 @@ int
drm_connector_create_standard_properties(struct drm_device *dev)drivers/gpu/drm/drm_connector.c int drm_connector_create_standard_properties(struct drm_device *dev)
Quoted 4 lines
drivers/gpu/drm/drm_connector.c +1
-0return -ENOMEM ; dev->mode_config.non_desktop_property = prop; + prop = drm_property_create_enum(dev, DRM_MODE_PROP_ENUM,"Colorspace",
drivers/gpu/drm/drm_connector.c int drm_connector_create_standard_properties(struct drm_device *dev) · line 1062
Quoted 1 line
drivers/gpu/drm/drm_connector.c +1
-0+ colorspace, ARRAY_SIZE(colorspace));Similar to what others have said: I'm not sure it's a great idea to expose the full set by default. At a minimum, actually applying this property requires some control over the HDMI/DP transmitter doesn't it? And I believe they vary in capabilities?
Quoted 3 lines
Further, I'd expect some of them to require more extensive changes further through the pipe (e.g. scRGB), though I admit I don't know much about how Sinks handle this stuff.
I am planning to separate out HDMI and DP as separate properties (same name for userspace), but with connector specific colorspaces in the list. Will float the v4 soon, please have a look and share your feedback.
Regards,
Uma Shankar
Quoted 79 lines
Do you have a subset which you have a real user and use-case for which we might settle on before throwing them all in and making it UAPI?
Cheers,
-BrianQuoted 72 lines
drivers/gpu/drm/drm_connector.c +4
-0+if (!prop) +return -ENOMEM ; + dev->mode_config.colorspace_property = prop; +return 0 ; }include/drm/drm_connector.h +7
-0@@ -497,6 +497,13 @@ struct drm_connector_state {unsigned int content_protection;/** +* @colorspace: Connector property to request colorspace +* change. This is most commonly used to switch to wider color +* gamuts like BT2020. +*/ +enum encoder_colorimetry colorspace; + +/** * @writeback_job: Writeback job for writeback connectors * * Holds the framebuffer and out-fence for a writeback connector. As (quoted diff) +0
-0
b/include/drm/drm_mode_config.hindex d643d26..a6eb0aa 100644include/drm/drm_mode_config.h +6
-0@@ -863,6 +863,12 @@ struct drm_mode_config {uint32_t cursor_width, cursor_height;/** +* @colorspace_property: Connector property to set the suitable +* colorspace supported by the sink. +*/ +struct drm_property *colorspace_property; + +/** * @suspend_state: * * Atomic state when suspended. include/uapi/drm/drm_mode.h +22
-0@@ -210,6 +210,30 @@#define DRM_MODE_CONTENT_PROTECTION_DESIRED 1#define DRM_MODE_CONTENT_PROTECTION_ENABLED 2 +enum encoder_colorimetry { +/* CEA 861 Normal Colorimetry options */ +COLORIMETRY_ITU_601 =0 , +COLORIMETRY_ITU_709 , +/* CEA 861 Extended Colorimetry Options */ +COLORIMETRY_XV_YCC_601 , +COLORIMETRY_XV_YCC_709 , +COLORIMETRY_S_YCC_601 , +COLORIMETRY_ADOBE_YCC_601 , +COLORIMETRY_ADOBE_RGB , +COLORIMETRY_BT2020_RGB , +COLORIMETRY_BT2020_YCC , +COLORIMETRY_BT2020_CYCC , +/* DP MSA Colorimetry Options */ +COLORIMETRY_Y_CBCR_ITU_601 , +COLORIMETRY_Y_CBCR_ITU_709 , +COLORIMETRY_SRGB , +COLORIMETRY_RGB_WIDE_GAMUT , +COLORIMETRY_SCRGB , +COLORIMETRY_DCI_P3 , +COLORIMETRY_CUSTOM_COLOR_PROFILE , +COLORIMETRY_DEFAULT =COLORIMETRY_ITU_709 , };
Quoted 8 lines
Quoted 8 lines
include/uapi/drm/drm_mode.h +1
-1+struct drm_mode_modeinfo {__u32 clock;__u16 hdisplay; --1.9.1
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
PATCH v2 2/2 drm/i915: Attach colorspace property and enable modeset
In reply to Uma ShankarThis patch attaches the colorspace connector property to the hdmi connector. Based on colorspace change, modeset will be triggered to switch to new colorspace.
Based on colorspace property value create an infoframe with appropriate colorspace. This can be used to send an infoframe packet with proper colorspace value set which will help to enable wider color gamut like BT2020 on sink.
v2: Merged the changes of creating infoframe as well to this patch as per Maarten's suggestion.
--- drivers/gpu/drm/i915/intel_atomic.c | 1 + drivers/gpu/drm/i915/intel_hdmi.c | 5 +++++ 2 files changed, 6 insertions(+)
drivers/gpu/drm/i915/intel_atomic.c +1 -0
@@ -125,6 +125,7 @@ int intel_digital_connector_atomic_check(struct drm_connector *conn,*/ if (new_conn_state->force_audio != old_conn_state->force_audio || new_conn_state->broadcast_rgb != old_conn_state->broadcast_rgb || + new_state->colorspace != old_state->colorspace || new_conn_state->base.picture_aspect_ratio != old_conn_state->base.picture_aspect_ratio || new_conn_state->base.content_type != old_conn_state->base.content_type || new_conn_state->base.scaling_mode != old_conn_state->base.scaling_mode)
drivers/gpu/drm/i915/intel_hdmi.c +5 -0
@@ -486,6 +486,8 @@ static void intel_hdmi_set_avi_infoframe(struct intel_encoder *encoder,else frame.avi.colorspace =HDMI_COLORSPACE_RGB ; + frame.avi.extended_colorimetry = conn_state->colorspace; + drm_hdmi_avi_infoframe_quant_range(&frame.avi, adjusted_mode, crtc_state->limited_color_range ? HDMI_QUANTIZATION_RANGE_LIMITED :
@@ -2125,6 +2127,9 @@ static void intel_hdmi_destroy(struct drm_connector *connector)intel_attach_broadcast_rgb_property (connector);intel_attach_aspect_ratio_property (connector);drm_connector_attach_content_type_property (connector); +drm_object_attach_property (&connector->base, + connector->dev->mode_config.colorspace_property, +COLORIMETRY_ITU_709 ); connector->state->picture_aspect_ratio =HDMI_PICTURE_ASPECT_NONE ; }
Signature · 6 lines
1.9.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Maarten Lankhorst
maintainerRe: [v2 2/2] drm/i915: Attach colorspace property and enable modeset
Op 31-10-18 om 13:05 schreef Uma Shankar:
Quoted 44 lines
This patch attaches the colorspace connector property to the hdmi connector. Based on colorspace change, modeset will be triggered to switch to new colorspace.
Based on colorspace property value create an infoframe with appropriate colorspace. This can be used to send an infoframe packet with proper colorspace value set which will help to enable wider color gamut like BT2020 on sink.
v2: Merged the changes of creating infoframe as well to this patch as per Maarten's suggestion.
Signed-off-by Uma Shankar <[email protected]>--- drivers/gpu/drm/i915/intel_atomic.c | 1 + drivers/gpu/drm/i915/intel_hdmi.c | 5 +++++ 2 files changed, 6 insertions(+)drivers/gpu/drm/i915/intel_atomic.c +1
-0@@ -125,6 +125,7 @@ int intel_digital_connector_atomic_check(struct drm_connector *conn,*/ if (new_conn_state->force_audio != old_conn_state->force_audio || new_conn_state->broadcast_rgb != old_conn_state->broadcast_rgb || + new_state->colorspace != old_state->colorspace || new_conn_state->base.picture_aspect_ratio != old_conn_state->base.picture_aspect_ratio || new_conn_state->base.content_type != old_conn_state->base.content_type || new_conn_state->base.scaling_mode != old_conn_state->base.scaling_mode)drivers/gpu/drm/i915/intel_hdmi.c +2
-0@@ -486,6 +486,8 @@ static void intel_hdmi_set_avi_infoframe(struct intel_encoder *encoder,else frame.avi.colorspace =HDMI_COLORSPACE_RGB ; + frame.avi.extended_colorimetry = conn_state->colorspace; + drm_hdmi_avi_infoframe_quant_range(&frame.avi, adjusted_mode, crtc_state->limited_color_range ? HDMI_QUANTIZATION_RANGE_LIMITED :
drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 2132
Quoted 6 lines
drivers/gpu/drm/i915/intel_hdmi.c +3
-0@@ -2125,6 +2127,9 @@ static void intel_hdmi_destroy(struct drm_connector *connector)intel_attach_broadcast_rgb_property (connector);intel_attach_aspect_ratio_property (connector);drm_connector_attach_content_type_property (connector); +drm_object_attach_property (&connector->base, + connector->dev->mode_config.colorspace_property, +COLORIMETRY_ITU_709 );
Just put 0 here..
If you want to init the default colorspace, put it in the first patch.
We should perhaps hide color spaces that are not supported on HDMI?
drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 2135
Quoted 3 lines
drivers/gpu/drm/i915/intel_hdmi.c +0
-0connector->state->picture_aspect_ratio =HDMI_PICTURE_ASPECT_NONE ; }
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [v2 2/2] drm/i915: Attach colorspace property and enable modeset
Quoted 67 lines
-----Original Message-----
From: Maarten Lankhorst [mailto:[email protected]]
Sent: Friday, November 2, 2018 2:53 PM
To: Shankar, Uma <[email protected]>; [email protected]; [email protected]
Cc: Syrjala, Ville <[email protected]>; [email protected]; Lankhorst, Maarten <[email protected]>
Subject: Re: [Intel-gfx] [v2 2/2] drm/i915: Attach colorspace property and enable modesetOp 31-10-18 om 13:05 schreef Uma Shankar:
drivers/gpu/drm/i915/intel_atomic.c int intel_digital_connector_atomic_check(struct
Quoted 24 lines
This patch attaches the colorspace connector property to the hdmi connector. Based on colorspace change, modeset will be triggered to switch to new colorspace.
Based on colorspace property value create an infoframe with appropriate colorspace. This can be used to send an infoframe packet with proper colorspace value set which will help to enable wider color gamut like BT2020 on sink.
v2: Merged the changes of creating infoframe as well to this patch as per Maarten's suggestion.
Signed-off-by Uma Shankar <[email protected]>--- drivers/gpu/drm/i915/intel_atomic.c | 1 + drivers/gpu/drm/i915/intel_hdmi.c | 5 +++++ 2 files changed, 6 insertions(+)drivers/gpu/drm/i915/intel_atomic.c +0
-0@@ -125,6 +125,7 @@ int intel_digital_connector_atomic_check(struct
drm_connector*conn,drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_set_avi_infoframe(struct
Quoted 17 lines
drivers/gpu/drm/i915/intel_atomic.c +0
-0*/ if (new_conn_state->force_audio != old_conn_state->force_audio || new_conn_state->broadcast_rgb != old_conn_state->broadcast_rgb||
drivers/gpu/drm/i915/intel_atomic.c +1
-0+ new_state->colorspace != old_state->colorspace || new_conn_state->base.picture_aspect_ratio != old_conn_state-base.picture_aspect_ratio ||
new_conn_state->base.content_type!= old_conn_state-
base.content_type ||
new_conn_state->base.scaling_mode!=old_conn_state->base.scaling_mode)drivers/gpu/drm/i915/intel_hdmi.c +0
-0@@ -486,6 +486,8 @@ static void intel_hdmi_set_avi_infoframe(struct
intel_encoder*encoder,drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_set_avi_infoframe(struct intel_encoder *encoder,
Quoted 8 lines
drivers/gpu/drm/i915/intel_hdmi.c +2
-0else frame.avi.colorspace =HDMI_COLORSPACE_RGB ; + frame.avi.extended_colorimetry = conn_state->colorspace; + drm_hdmi_avi_infoframe_quant_range(&frame.avi, adjusted_mode, crtc_state->limited_color_range ?
HDMI_QUANTIZATION_RANGE_LIMITED:drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector
Quoted 1 line
drivers/gpu/drm/i915/intel_hdmi.c +0
-0@@ -2125,6 +2127,9 @@ static void intel_hdmi_destroy(struct drm_connector*connector)
Quoted 8 lines
drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 2132
Quoted 6 lines
drivers/gpu/drm/i915/intel_hdmi.c +3
-0intel_attach_broadcast_rgb_property (connector);intel_attach_aspect_ratio_property (connector);drm_connector_attach_content_type_property (connector); +drm_object_attach_property (&connector->base, + connector->dev->mode_config.colorspace_property, +COLORIMETRY_ITU_709 );Just put 0 here..
If you want to init the default colorspace, put it in the first patch.
Ok, will update this.
Quoted 1 line
We should perhaps hide color spaces that are not supported on HDMI?
Currently the supported colorspaces will be picked from edid by userspace and they should use the current property interface to set the one which is supported. Even on HDMI, some connectors may not support certain colorspace, so keeping it on userspace to set the one which is supported by the particular connector. Hope this approach is fine ?
Regards,
Uma Shankar
Quoted 5 lines
drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector · line 2133
Quoted 1 line
drivers/gpu/drm/i915/intel_hdmi.c +0
-0connector->state->picture_aspect_ratio =
HDMI_PICTURE_ASPECT_NONE;Quoted 2 lines
drivers/gpu/drm/i915/intel_hdmi.c +0
-0}
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [Intel-gfx] [v2 2/2] drm/i915: Attach colorspace property and enable modeset
Quoted 78 lines · Uma
Quoted 67 lines
-----Original Message-----
From: Maarten Lankhorst [mailto:[email protected]]
Sent: Friday, November 2, 2018 2:53 PM
To: Shankar, Uma <[email protected]>; [email protected]; [email protected]
Cc: Syrjala, Ville <[email protected]>; [email protected]; Lankhorst, Maarten <[email protected]>
Subject: Re: [Intel-gfx] [v2 2/2] drm/i915: Attach colorspace property and enable modesetOp 31-10-18 om 13:05 schreef Uma Shankar:
drivers/gpu/drm/i915/intel_atomic.c int intel_digital_connector_atomic_check(struct
Quoted 24 lines
This patch attaches the colorspace connector property to the hdmi connector. Based on colorspace change, modeset will be triggered to switch to new colorspace.
Based on colorspace property value create an infoframe with appropriate colorspace. This can be used to send an infoframe packet with proper colorspace value set which will help to enable wider color gamut like BT2020 on sink.
v2: Merged the changes of creating infoframe as well to this patch as per Maarten's suggestion.
Signed-off-by Uma Shankar <[email protected]>--- drivers/gpu/drm/i915/intel_atomic.c | 1 + drivers/gpu/drm/i915/intel_hdmi.c | 5 +++++ 2 files changed, 6 insertions(+)drivers/gpu/drm/i915/intel_atomic.c +0
-0@@ -125,6 +125,7 @@ int intel_digital_connector_atomic_check(struct
drm_connector*conn,drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_set_avi_infoframe(struct
Quoted 17 lines
drivers/gpu/drm/i915/intel_atomic.c +0
-0*/ if (new_conn_state->force_audio != old_conn_state->force_audio || new_conn_state->broadcast_rgb != old_conn_state->broadcast_rgb||
drivers/gpu/drm/i915/intel_atomic.c +1
-0+ new_state->colorspace != old_state->colorspace || new_conn_state->base.picture_aspect_ratio != old_conn_state-base.picture_aspect_ratio ||
new_conn_state->base.content_type!= old_conn_state-
base.content_type ||
new_conn_state->base.scaling_mode!=old_conn_state->base.scaling_mode)drivers/gpu/drm/i915/intel_hdmi.c +0
-0@@ -486,6 +486,8 @@ static void intel_hdmi_set_avi_infoframe(struct
intel_encoder*encoder,drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_set_avi_infoframe(struct intel_encoder *encoder,
Quoted 8 lines
drivers/gpu/drm/i915/intel_hdmi.c +2
-0else frame.avi.colorspace =HDMI_COLORSPACE_RGB ; + frame.avi.extended_colorimetry = conn_state->colorspace; + drm_hdmi_avi_infoframe_quant_range(&frame.avi, adjusted_mode, crtc_state->limited_color_range ?
HDMI_QUANTIZATION_RANGE_LIMITED:drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector
Quoted 1 line
drivers/gpu/drm/i915/intel_hdmi.c +0
-0@@ -2125,6 +2127,9 @@ static void intel_hdmi_destroy(struct drm_connector*connector)
Quoted 8 lines
drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 2132
Quoted 6 lines
drivers/gpu/drm/i915/intel_hdmi.c +3
-0intel_attach_broadcast_rgb_property (connector);intel_attach_aspect_ratio_property (connector);drm_connector_attach_content_type_property (connector); +drm_object_attach_property (&connector->base, + connector->dev->mode_config.colorspace_property, +COLORIMETRY_ITU_709 );Just put 0 here..
If you want to init the default colorspace, put it in the first patch.Ok, will update this.
Quoted 7 lines
Quoted 1 line
We should perhaps hide color spaces that are not supported on HDMI?
Currently the supported colorspaces will be picked from edid by userspace and they should use the current property interface to set the one which is supported. Even on HDMI, some connectors may not support certain colorspace, so keeping it on userspace to set the one which is supported by the particular connector. Hope this approach is fine ?
I think we want to trim the list to whatever the infoframe vs. MSA/VSC SDP can carry. So HDMI will have one list, DP another. And I guess for lspcon we want to go with the HDMI definition since we populate the infoframe by hand.
Signature · 6 lines
Ville Syrjälä Intel _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Maarten Lankhorst
maintainerRe: [v2 2/2] drm/i915: Attach colorspace property and enable modeset
Op 02-11-18 om 16:41 schreef Ville Syrjälä:
Quoted 83 lines · Uma
Quoted 74 lines
Quoted 66 lines
-----Original Message-----
From: Maarten Lankhorst [mailto:[email protected]]
Sent: Friday, November 2, 2018 2:53 PM
To: Shankar, Uma <[email protected]>; [email protected]; [email protected]
Cc: Syrjala, Ville <[email protected]>; [email protected]; Lankhorst, Maarten <[email protected]>
Subject: Re: [Intel-gfx] [v2 2/2] drm/i915: Attach colorspace property and enable modesetOp 31-10-18 om 13:05 schreef Uma Shankar:
drivers/gpu/drm/i915/intel_atomic.c int intel_digital_connector_atomic_check(struct
Quoted 24 lines
This patch attaches the colorspace connector property to the hdmi connector. Based on colorspace change, modeset will be triggered to switch to new colorspace.
Based on colorspace property value create an infoframe with appropriate colorspace. This can be used to send an infoframe packet with proper colorspace value set which will help to enable wider color gamut like BT2020 on sink.
v2: Merged the changes of creating infoframe as well to this patch as per Maarten's suggestion.
Signed-off-by Uma Shankar <[email protected]>--- drivers/gpu/drm/i915/intel_atomic.c | 1 + drivers/gpu/drm/i915/intel_hdmi.c | 5 +++++ 2 files changed, 6 insertions(+)drivers/gpu/drm/i915/intel_atomic.c +0
-0@@ -125,6 +125,7 @@ int intel_digital_connector_atomic_check(struct
drm_connector*conn,drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_set_avi_infoframe(struct
Quoted 17 lines
drivers/gpu/drm/i915/intel_atomic.c +0
-0*/ if (new_conn_state->force_audio != old_conn_state->force_audio || new_conn_state->broadcast_rgb != old_conn_state->broadcast_rgb||
drivers/gpu/drm/i915/intel_atomic.c +1
-0+ new_state->colorspace != old_state->colorspace || new_conn_state->base.picture_aspect_ratio != old_conn_state-base.picture_aspect_ratio ||
new_conn_state->base.content_type!= old_conn_state-
base.content_type ||
new_conn_state->base.scaling_mode!=old_conn_state->base.scaling_mode)drivers/gpu/drm/i915/intel_hdmi.c +0
-0@@ -486,6 +486,8 @@ static void intel_hdmi_set_avi_infoframe(struct
intel_encoder*encoder,drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_set_avi_infoframe(struct intel_encoder *encoder,
Quoted 8 lines
drivers/gpu/drm/i915/intel_hdmi.c +2
-0else frame.avi.colorspace =HDMI_COLORSPACE_RGB ; + frame.avi.extended_colorimetry = conn_state->colorspace; + drm_hdmi_avi_infoframe_quant_range(&frame.avi, adjusted_mode, crtc_state->limited_color_range ?
HDMI_QUANTIZATION_RANGE_LIMITED:drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector
Quoted 1 line
drivers/gpu/drm/i915/intel_hdmi.c +0
-0@@ -2125,6 +2127,9 @@ static void intel_hdmi_destroy(struct drm_connector*connector)
Quoted 8 lines
drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 2132
Quoted 6 lines
drivers/gpu/drm/i915/intel_hdmi.c +3
-0intel_attach_broadcast_rgb_property (connector);intel_attach_aspect_ratio_property (connector);drm_connector_attach_content_type_property (connector); +drm_object_attach_property (&connector->base, + connector->dev->mode_config.colorspace_property, +COLORIMETRY_ITU_709 );Just put 0 here..
If you want to init the default colorspace, put it in the first patch.Quoted 8 lines
Ok, will update this.
Quoted 1 line
We should perhaps hide color spaces that are not supported on HDMI?
Currently the supported colorspaces will be picked from edid by userspace and they should use the current property interface to set the one which is supported. Even on HDMI, some connectors may not support certain colorspace, so keeping it on userspace to set the one which is supported by the particular connector. Hope this approach is fine ?
Quoted 5 lines
I think we want to trim the list to whatever the infoframe vs. MSA/VSC SDP can carry. So HDMI will have one list, DP another. And I guess for lspcon we want to go with the HDMI definition since we populate the infoframe by hand.
What about passive DP to HDMI convertors?
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [v2 2/2] drm/i915: Attach colorspace property and enable modeset
Quoted 84 lines · Maarten Lankhorst
Op 02-11-18 om 16:41 schreef Ville Syrjälä:
Quoted 83 lines · Uma
Quoted 82 lines
Quoted 66 lines
-----Original Message-----
From: Maarten Lankhorst [mailto:[email protected]]
Sent: Friday, November 2, 2018 2:53 PM
To: Shankar, Uma <[email protected]>; [email protected]; [email protected]
Cc: Syrjala, Ville <[email protected]>; [email protected]; Lankhorst, Maarten <[email protected]>
Subject: Re: [Intel-gfx] [v2 2/2] drm/i915: Attach colorspace property and enable modesetOp 31-10-18 om 13:05 schreef Uma Shankar:
drivers/gpu/drm/i915/intel_atomic.c int intel_digital_connector_atomic_check(struct
Quoted 24 lines
This patch attaches the colorspace connector property to the hdmi connector. Based on colorspace change, modeset will be triggered to switch to new colorspace.
Based on colorspace property value create an infoframe with appropriate colorspace. This can be used to send an infoframe packet with proper colorspace value set which will help to enable wider color gamut like BT2020 on sink.
v2: Merged the changes of creating infoframe as well to this patch as per Maarten's suggestion.
Signed-off-by Uma Shankar <[email protected]>--- drivers/gpu/drm/i915/intel_atomic.c | 1 + drivers/gpu/drm/i915/intel_hdmi.c | 5 +++++ 2 files changed, 6 insertions(+)drivers/gpu/drm/i915/intel_atomic.c +0
-0@@ -125,6 +125,7 @@ int intel_digital_connector_atomic_check(struct
drm_connector*conn,drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_set_avi_infoframe(struct
Quoted 17 lines
drivers/gpu/drm/i915/intel_atomic.c +0
-0*/ if (new_conn_state->force_audio != old_conn_state->force_audio || new_conn_state->broadcast_rgb != old_conn_state->broadcast_rgb||
drivers/gpu/drm/i915/intel_atomic.c +1
-0+ new_state->colorspace != old_state->colorspace || new_conn_state->base.picture_aspect_ratio != old_conn_state-base.picture_aspect_ratio ||
new_conn_state->base.content_type!= old_conn_state-
base.content_type ||
new_conn_state->base.scaling_mode!=old_conn_state->base.scaling_mode)drivers/gpu/drm/i915/intel_hdmi.c +0
-0@@ -486,6 +486,8 @@ static void intel_hdmi_set_avi_infoframe(struct
intel_encoder*encoder,drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_set_avi_infoframe(struct intel_encoder *encoder,
Quoted 8 lines
drivers/gpu/drm/i915/intel_hdmi.c +2
-0else frame.avi.colorspace =HDMI_COLORSPACE_RGB ; + frame.avi.extended_colorimetry = conn_state->colorspace; + drm_hdmi_avi_infoframe_quant_range(&frame.avi, adjusted_mode, crtc_state->limited_color_range ?
HDMI_QUANTIZATION_RANGE_LIMITED:drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector
Quoted 1 line
drivers/gpu/drm/i915/intel_hdmi.c +0
-0@@ -2125,6 +2127,9 @@ static void intel_hdmi_destroy(struct drm_connector*connector)
Quoted 8 lines
drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 2132
Quoted 6 lines
drivers/gpu/drm/i915/intel_hdmi.c +3
-0intel_attach_broadcast_rgb_property (connector);intel_attach_aspect_ratio_property (connector);drm_connector_attach_content_type_property (connector); +drm_object_attach_property (&connector->base, + connector->dev->mode_config.colorspace_property, +COLORIMETRY_ITU_709 );Just put 0 here..
If you want to init the default colorspace, put it in the first patch.Ok, will update this.
Quoted 1 line
We should perhaps hide color spaces that are not supported on HDMI?
Currently the supported colorspaces will be picked from edid by userspace and they should use the current property interface to set the one which is supported. Even on HDMI, some connectors may not support certain colorspace, so keeping it on userspace to set the one which is supported by the particular connector. Hope this approach is fine ?
Quoted 6 lines
Quoted 5 lines
I think we want to trim the list to whatever the infoframe vs. MSA/VSC SDP can carry. So HDMI will have one list, DP another. And I guess for lspcon we want to go with the HDMI definition since we populate the infoframe by hand.
What about passive DP to HDMI convertors?
By passive you mean DP++? Those are HDMI for us.
External DP->HDMI protocol converters are perhaps more tricky, but since we treat those as pure DP now and don't send any infoframes I think we should do the same when it comes to the exposed valeus for the property.
Signature · 6 lines
Ville Syrjälä Intel _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [v2 2/2] drm/i915: Attach colorspace property and enable modeset
In reply to Uma ShankarRegards
Shashank
Quoted 35 lines · Uma Shankar
This patch attaches the colorspace connector property to the hdmi connector. Based on colorspace change, modeset will be triggered to switch to new colorspace.
Based on colorspace property value create an infoframe with appropriate colorspace. This can be used to send an infoframe packet with proper colorspace value set which will help to enable wider color gamut like BT2020 on sink.
v2: Merged the changes of creating infoframe as well to this patch as per Maarten's suggestion.
Signed-off-by Uma Shankar <[email protected]>--- drivers/gpu/drm/i915/intel_atomic.c | 1 + drivers/gpu/drm/i915/intel_hdmi.c | 5 +++++ 2 files changed, 6 insertions(+)drivers/gpu/drm/i915/intel_atomic.c +1
-0@@ -125,6 +125,7 @@ int intel_digital_connector_atomic_check(struct drm_connector *conn,*/ if (new_conn_state->force_audio != old_conn_state->force_audio || new_conn_state->broadcast_rgb != old_conn_state->broadcast_rgb || + new_state->colorspace != old_state->colorspace || new_conn_state->base.picture_aspect_ratio != old_conn_state->base.picture_aspect_ratio || new_conn_state->base.content_type != old_conn_state->base.content_type || new_conn_state->base.scaling_mode != old_conn_state->base.scaling_mode)drivers/gpu/drm/i915/intel_hdmi.c +0
-0
drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_set_avi_infoframe(struct intel_encoder *encoder, · line 490
Quoted 5 lines
drivers/gpu/drm/i915/intel_hdmi.c +2
-0@@ -486,6 +486,8 @@ static void intel_hdmi_set_avi_infoframe(struct intel_encoder *encoder,else frame.avi.colorspace =HDMI_COLORSPACE_RGB ; + frame.avi.extended_colorimetry = conn_state->colorspace; +
We must also set the date byte 2 bits C1-C0 (colorimetry part) to indicate the use of extended colorimetry bits, so that monitor will refer to extended colorimetry data, else it wont even bother looking at it:
Extended Colorimetry Information Valid (colorimetry indicated in bits EC0, EC1, and EC2)
Its right now set to dafault 0-0 I guess, indicating No data We should also set it to a default value now, when we have started bothering about gamut.
Regards
Shashank
drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 2135
Quoted 13 lines
drivers/gpu/drm/i915/intel_hdmi.c +3
-0drm_hdmi_avi_infoframe_quant_range(&frame.avi, adjusted_mode, crtc_state->limited_color_range ? HDMI_QUANTIZATION_RANGE_LIMITED :@@ -2125,6 +2127,9 @@ static void intel_hdmi_destroy(struct drm_connector *connector)intel_attach_broadcast_rgb_property (connector);intel_attach_aspect_ratio_property (connector);drm_connector_attach_content_type_property (connector); +drm_object_attach_property (&connector->base, + connector->dev->mode_config.colorspace_property, +COLORIMETRY_ITU_709 ); connector->state->picture_aspect_ratio =HDMI_PICTURE_ASPECT_NONE ; }
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Patchwork
CI✗ Fi.CI.CHECKPATCH: warning for Add Colorspace connector property interface (rev2)
In reply to Uma Shankar== Series Details ==
== Series Details ==
Series: Add Colorspace connector property interface (rev2)
URL : https://patchwork.freedesktop.org/series/47132/
State : warning
== Summary ==
$ dim checkpatch origin/drm-tip b716d24947ce drm: Add colorspace property 33d07ea8810b drm/i915: Attach colorspace property and enable modeset -:50: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis #50: FILE: drivers/gpu/drm/i915/intel_hdmi.c:2131: + drm_object_attach_property(&connector->base, + connector->dev->mode_config.colorspace_property,
total: 0 errors, 0 warnings, 1 checks, 24 lines checked
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✗ Fi.CI.SPARSE: warning for Add Colorspace connector property interface (rev2)
In reply to Uma Shankar== Series Details ==
== Series Details ==
Series: Add Colorspace connector property interface (rev2)
URL : https://patchwork.freedesktop.org/series/47132/
State : warning
== Summary ==
$ dim sparse origin/drm-tip Sparse version: v0.5.2 Commit: drm: Add colorspace property Okay!
Commit: drm/i915: Attach colorspace property and enable modeset+drivers/gpu/drm/i915/intel_hdmi.c:489:52: int enum encoder_colorimetry versus+drivers/gpu/drm/i915/intel_hdmi.c:489:52: int enum hdmi_extended_colorimetry+drivers/gpu/drm/i915/intel_hdmi.c:489:52: warning: mixing different enum types
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✗ Fi.CI.BAT: failure for Add Colorspace connector property interface (rev2)
In reply to Uma Shankar== Series Details ==
== Series Details ==
Series: Add Colorspace connector property interface (rev2)
URL : https://patchwork.freedesktop.org/series/47132/
State : failure
== Summary ==
= CI Bug Log - changes from CI_DRM_5062 -> Patchwork_10663 =
== Summary - FAILURE ==
Serious unknown changes coming with Patchwork_10663 absolutely need to be verified manually.
If you think the reported changes have nothing to do with the changes introduced in Patchwork_10663, please notify your bug team to allow them to document this new failure mode, which will reduce false positives in CI.
External URL: https://patchwork.freedesktop.org/api/1.0/series/47132/revisions/2/mbox/
== Possible new issues ==
Here are the unknown changes that may have been introduced in Patchwork_10663:
=== IGT changes ===
==== Possible regressions ====
igt@debugfs_test@read_all_entries:
fi-skl-iommu: PASS -> INCOMPLETE
fi-ivb-3770: PASS -> INCOMPLETE
fi-cfl-s3: PASS -> INCOMPLETE
fi-hsw-peppy: PASS -> INCOMPLETE
fi-skl-6260u: PASS -> INCOMPLETE
fi-icl-u: PASS -> INCOMPLETE
fi-snb-2600: PASS -> INCOMPLETE
fi-hsw-4770r: PASS -> INCOMPLETE
fi-kbl-guc: PASS -> FAIL
fi-bsw-kefka: PASS -> INCOMPLETE
fi-skl-6700hq: PASS -> INCOMPLETE
fi-kbl-x1275: PASS -> FAIL
fi-kbl-7500u: PASS -> INCOMPLETE
fi-blb-e6850: PASS -> INCOMPLETE
fi-bwr-2160: PASS -> INCOMPLETE
fi-bdw-5557u: PASS -> INCOMPLETE
fi-kbl-r: PASS -> INCOMPLETE
fi-kbl-7567u: PASS -> INCOMPLETE
fi-cnl-u: PASS -> INCOMPLETE
fi-gdg-551: PASS -> INCOMPLETE
fi-cfl-8109u: PASS -> INCOMPLETE
fi-skl-6600u: PASS -> INCOMPLETE
fi-cfl-8700k: PASS -> INCOMPLETE
fi-whl-u: PASS -> INCOMPLETE
fi-pnv-d510: PASS -> INCOMPLETE
fi-ivb-3520m: PASS -> INCOMPLETE
fi-bsw-n3050: PASS -> INCOMPLETE
fi-skl-6700k2: PASS -> INCOMPLETE
fi-hsw-4770: PASS -> INCOMPLETE
fi-kbl-soraka: PASS -> INCOMPLETE
fi-skl-6770hq: PASS -> INCOMPLETE
igt@gem_exec_suspend@basic-s3:
fi-kbl-x1275: PASS -> INCOMPLETE
==== Warnings ====
igt@debugfs_test@read_all_entries:
fi-icl-u2: DMESG-WARN (fdo#108070) -> INCOMPLETE== Known issues ==
Here are the changes found in Patchwork_10663 that come from known issues:
=== IGT changes ===
==== Issues hit ====
igt@debugfs_test@read_all_entries:
fi-glk-dsi: PASS -> INCOMPLETE (fdo#103359, k.org#198133)
fi-skl-gvtdvm: PASS -> INCOMPLETE (fdo#105600)
fi-bdw-gvtdvm: PASS -> INCOMPLETE (fdo#105600)
fi-bxt-j4205: PASS -> INCOMPLETE (fdo#103927)
fi-skl-guc: PASS -> INCOMPLETE (fdo#106693)
fi-apl-guc: PASS -> INCOMPLETE (fdo#106693)
fi-glk-j4005: PASS -> INCOMPLETE (fdo#103359, k.org#198133)
fi-byt-clapper: PASS -> INCOMPLETE (fdo#102657)
fi-byt-j1900: PASS -> INCOMPLETE (fdo#102657)
fi-bxt-dsi: PASS -> INCOMPLETE (fdo#103927)
fi-kbl-7560u: PASS -> INCOMPLETE (fdo#103665)
fi-cfl-guc: PASS -> INCOMPLETE (fdo#106693)
igt@gem_exec_suspend@basic-s3:
fi-kbl-guc: PASS -> INCOMPLETE (fdo#106693) fdo#102657 https://bugs.freedesktop.org/show_bug.cgi?id=102657
fdo#103359 https://bugs.freedesktop.org/show_bug.cgi?id=103359
fdo#103665 https://bugs.freedesktop.org/show_bug.cgi?id=103665
fdo#103927 https://bugs.freedesktop.org/show_bug.cgi?id=103927
fdo#105600 https://bugs.freedesktop.org/show_bug.cgi?id=105600
fdo#106693 https://bugs.freedesktop.org/show_bug.cgi?id=106693
fdo#108070 https://bugs.freedesktop.org/show_bug.cgi?id=108070
k.org#198133 https://bugzilla.kernel.org/show_bug.cgi?id=198133
== Participating hosts (49 -> 44) ==
Missing (5): fi-ilk-m540 fi-hsw-4200u fi-byt-squawks fi-bsw-cyan fi-ctg-p8600
== Build changes ==
* Linux: CI_DRM_5062 -> Patchwork_10663
CI_DRM_5062: 3aa71a0d803ee01605f9a3026ddd989a591a73c6 @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_4703: f882a542a3eb24e78e51aa6410a3a67c0efb4e97 @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_10663: 33d07ea8810b104ee7f473d476386f8d662b3305 @ git://anongit.freedesktop.org/gfx-ci/linux
== Linux commits ==
33d07ea8810b drm/i915: Attach colorspace property and enable modeset b716d24947ce drm: Add colorspace property
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_10663/issues.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Hello Uma,
My comments inline.
Quoted 11 lines · Uma Shankar
This patch series creates a new connector property to program colorspace to sink devices. Modern sink devices support more than 1 type of colorspace like 601, 709, BT2020 etc. This helps to switch based on content type which is to be displayed. The decision lies with compositors as to in which scenarios, a particular colorspace will be picked.
This will be helpful mostly to switch to higher gamut colorspaces like BT2020 when the media content is encoded as BT2020. Thereby giving a good visual experience to users.
Quoted 5 lines
The expectation from userspace is that it should parse the EDID and get supported colorspaces. Use this property and switch to the one supported. Kernel will not give the supported colorspaces since this is panel dependent and our curremt property infrastructure is not supporting it.
I am not very sure about this part, consider a situation where, I have connected a HDMI 2.0 monitor which supports BT2020 gamut, to a GEN9 device, running an user-space which can also support BT2020 playback / HDR playback. Now, both monitor and user-space supports BT2020 playback, but the HW doesn't, and this will create a problem during playback. So I gess we need to expose a kernel Cap or property to showcase if the HW can support BT2020/DCI-P3 gamut space or not.
- Shashank
Quoted 10 lines
Have tested this using xrandr by using below command:
xrandr --output HDMI2 --set "Colorspace" "BT2020_rgb"v2: Addressed Ville and Maarten's review comments. Merged the 2nd and 3rd patch into one common logical patch.
Uma Shankar (2):
drm: Add colorspace property
drm/i915: Attach colorspace property and enable modeset
Quoted 9 lines
drivers/gpu/drm/drm_atomic_uapi.c | 4 ++++ drivers/gpu/drm/drm_connector.c | 44 +++++++++++++++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_atomic.c | 1 + drivers/gpu/drm/i915/intel_hdmi.c | 5 +++++ include/drm/drm_connector.h | 7 ++++++ include/drm/drm_mode_config.h | 6 +++++ include/uapi/drm/drm_mode.h | 24 ++++++++++++++++++++ 7 files changed, 91 insertions(+)
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx