Skip to contentSkip to conversation

media: platform: Add Aspeed Video Engine Driver

PATCH Superseded Eddie James 3 participants 8 messages Nov 12, 2018 – Nov 27, 2018

Subsystems (3)

v5 of 8 Superseded Latest is v8 →

lore
Share & tools
lore
#0 lore raw

v5 cover media: platform: Add Aspeed Video Engine Driver

From: Eddie James <[email protected]>

The Video Engine (VE) embedded in the Aspeed AST2400 and AST2500 SOCs can capture and compress video data from digital or analog sources. With the Aspeed chip acting as a service processor, the Video Engine can capture the host processor graphics output.

This series adds a V4L2 driver for the VE, providing the usual V4L2 streaming interface by way of videobuf2. Each frame, the driver triggers the hardware to capture the host graphics output and compress it to JPEG format.

v4l-utils HEAD dd3ff81f58c4e1e6f33765dc61ad33c48ae6bb07

v4l2-compliance SHA: not available, 32 bits

Compliance test for device /dev/video0:

Driver Info:

	Driver name      : aspeed-video
	Card type        : Aspeed Video Engine
	Bus info         : platform:aspeed-video
	Driver version   : 4.18.12
	Capabilities     : 0x85200001

Video Capture
Read/Write
Streaming
Extended Pix Format
Device Capabilities
Device Caps : 0x05200001
Video Capture
Read/Write
Streaming
Extended Pix Format

Required ioctls:
test VIDIOC_QUERYCAP: OK

Allow for multiple opens:
test second /dev/video0 open: OK
test VIDIOC_QUERYCAP: OK
test VIDIOC_G/S_PRIORITY: OK
test for unlimited opens: OK

Debug ioctls:
test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported) test VIDIOC_LOG_STATUS: OK (Not Supported)

Input ioctls:
test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported) test VIDIOC_ENUMAUDIO: OK (Not Supported)
test VIDIOC_G/S/ENUMINPUT: OK
test VIDIOC_G/S_AUDIO: OK (Not Supported)
Inputs: 1 Audio Inputs: 0 Tuners: 0

Output ioctls:
test VIDIOC_G/S_MODULATOR: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_ENUMAUDOUT: OK (Not Supported) test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) test VIDIOC_G/S_AUDOUT: OK (Not Supported)
Outputs: 0 Audio Outputs: 0 Modulators: 0

Input/Output configuration ioctls:
test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK test VIDIOC_DV_TIMINGS_CAP: OK
test VIDIOC_G/S_EDID: OK (Not Supported)

Control ioctls (Input 0):
test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
test VIDIOC_QUERYCTRL: OK
test VIDIOC_G/S_CTRL: OK
test VIDIOC_G/S/TRY_EXT_CTRLS: OK
fail: v4l2-test-controls.cpp(823): failed to find event for control 'Chroma Subsampling'
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
Standard Controls: 3 Private Controls: 0

Format ioctls (Input 0):
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK test VIDIOC_G/S_PARM: OK
test VIDIOC_G_FBUF: OK (Not Supported) test VIDIOC_G_FMT: OK
test VIDIOC_TRY_FMT: OK
test VIDIOC_S_FMT: OK
test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) test Cropping: OK (Not Supported)
test Composing: OK (Not Supported)
test Scaling: OK (Not Supported)

Codec ioctls (Input 0):
test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) test VIDIOC_G_ENC_INDEX: OK (Not Supported) test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)

Buffer ioctls (Input 0):
fail: v4l2-test-buffers.cpp(422): dmabuf_valid ^ !!(caps & V4L2_BUF_CAP_SUPPORTS_DMABUF)
test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: FAIL
test VIDIOC_EXPBUF: OK (Not Supported)

Test input 0:

Streaming ioctls:
test read/write: OK
test blocking wait: OK
test MMAP: OK
test USERPTR: OK (Not Supported)
fail: v4l2-test-buffers.cpp(1102): exp_q.reqbufs(expbuf_node, q.g_buffers())
fail: v4l2-test-buffers.cpp(1192): setupDmaBuf(expbuf_node, node, q, exp_q)
test DMABUF: FAIL

Total: 48, Succeeded: 45, Failed: 3, Warnings: 0

The apparent rate of change to the v4l2/vb2 API makes it difficult to pass these tests. None of the failing tests even ran last time I submitted my series. And V4L2_BUF_CAP_SUPPORTS_DMABUF is undefined in 4.19.

Changes since v4:
- Set real min and max resolution in enum_dv_timings
- Add check for vb2_is_busy before settings the timings
- Set max frame rate to the actual max rather than max + 1
- Correct the input status to 0.
- Rework resolution change to only set the relevant h/w regs during startup or when set_timings is called.

Changes since v3:
- Switch update reg function to use u32 clear rather than unsigned long mask
- Add timing information from host VGA signal
- Fix binding documentation mispelling
- Fix upper case hex values
- Add wait_prepare and wait_finish
- Set buffer state to queued (rather than error) if streaming fails to start
- Switch engine busy print statement to error
- Removed a couple unecessary type assignments in v4l2 ioctls
- Added query_dv_timings, fixed get_dv_timings
- Corrected source change event to fire if and only if size actually changes
- Locked open and release

Changes since v2:
- Switch to streaming interface. This involved a lot of changes.
- Rework memory allocation due to using videobuf2 buffers, but also only allocate the necessary size of source buffer rather than the max size

Changes since v1:
- Removed le32_to_cpu calls for JPEG header data
- Reworked v4l2 ioctls to be compliant.
- Added JPEG controls
- Updated devicetree docs according to Rob's suggestions.
- Added myself to MAINTAINERS

Eddie James (2):
dt-bindings: media: Add Aspeed Video Engine binding documentation
media: platform: Add Aspeed Video Engine driver

 .../devicetree/bindings/media/aspeed-video.txt     |   26 +
 MAINTAINERS                                        |    8 +
 drivers/media/platform/Kconfig                     |    9 +
 drivers/media/platform/Makefile                    |    1 +
 drivers/media/platform/aspeed-video.c              | 1711 ++++++++++++++++++++
 5 files changed, 1755 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/aspeed-video.txt
 create mode 100644 drivers/media/platform/aspeed-video.c
Signature · 1 line
1.8.3.1
#1 lore raw

PATCH v5 1/2 dt-bindings: media: Add Aspeed Video Engine binding documentation

Document the bindings.

---
 .../devicetree/bindings/media/aspeed-video.txt     | 26 ++++++++++++++++++++++
 1 file changed, 26 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/aspeed-video.txt
Documentation/devicetree/bindings/media/aspeed-video.txt new file +26 -0
new file mode 100644
index 0000000..78b464a
@@ -0,0 +1,26 @@
+* Device tree bindings for Aspeed Video Engine
+
+The Video Engine (VE) embedded in the Aspeed AST2400 and AST2500 SOCs can
+capture and compress video data from digital or analog sources.
+
+Required properties:
+ - compatible:		"aspeed,ast2400-video-engine" or
+			"aspeed,ast2500-video-engine"
+ - reg:			contains the offset and length of the VE memory region
+ - clocks:		clock specifiers for the syscon clocks associated with
+			the VE (ordering must match the clock-names property)
+ - clock-names:		"vclk" and "eclk"
+ - resets:		reset specifier for the syscon reset associated with
+			the VE
+ - interrupts:		the interrupt associated with the VE on this platform
+
+Example:
+
+video-engine at 1e700000 {
+    compatible = "aspeed,ast2500-video-engine";
+    reg = <0x1e700000 0x20000>;
+    clocks = <&syscon ASPEED_CLK_GATE_VCLK>, <&syscon ASPEED_CLK_GATE_ECLK>;
+    clock-names = "vclk", "eclk";
+    resets = <&syscon ASPEED_RESET_VIDEO>;
+    interrupts = <7>;
+};
Signature · 1 line
1.8.3.1
#2 lore raw

PATCH v5 2/2 media: platform: Add Aspeed Video Engine driver

In reply to Eddie James

The Video Engine (VE) embedded in the Aspeed AST2400 and AST2500 SOCs can capture and compress video data from digital or analog sources. With the Aspeed chip acting a service processor, the Video Engine can capture the host processor graphics output.

Add a V4L2 driver to capture video data and compress it to JPEG images. Make the video frames available through the V4L2 streaming interface.

---
 MAINTAINERS                           |    8 +
 drivers/media/platform/Kconfig        |    9 +
 drivers/media/platform/Makefile       |    1 +
 drivers/media/platform/aspeed-video.c | 1711 +++++++++++++++++++++++++++++++++
 4 files changed, 1729 insertions(+)
 create mode 100644 drivers/media/platform/aspeed-video.c
MAINTAINERS +8 -0
index fa45ff3..f8f08a4 100644
@@ -2414,6 +2414,14 @@ S:	Maintained
 F:	Documentation/hwmon/asc7621
 F:	drivers/hwmon/asc7621.c
 
+ASPEED VIDEO ENGINE DRIVER
+M:	Eddie James <[email protected]>
+L:	linux-media at vger.kernel.org
+L:	openbmc at lists.ozlabs.org (moderated for non-subscribers)
+S:	Maintained
+F:	drivers/media/platform/aspeed-video.c
+F:	Documentation/devicetree/bindings/media/aspeed-video.txt
+
 ASUS NOTEBOOKS AND EEEPC ACPI/WMI EXTRAS DRIVERS
 M:	Corentin Chary <[email protected]>
 L:	acpi4asus-user at lists.sourceforge.net
drivers/media/platform/Kconfig +9 -0
index 70c4f6c..ba78dd5 100644
@@ -32,6 +32,15 @@ source "drivers/media/platform/davinci/Kconfig"
 
 source "drivers/media/platform/omap/Kconfig"
 
+config VIDEO_ASPEED
+	tristate "Aspeed AST2400 and AST2500 Video Engine driver"
+	depends on VIDEO_V4L2
+	select VIDEOBUF2_DMA_CONTIG
+	help
+	  Support for the Aspeed Video Engine (VE) embedded in the Aspeed
+	  AST2400 and AST2500 SOCs. The VE can capture and compress video data
+	  from digital or analog sources.
+
 config VIDEO_SH_VOU
 	tristate "SuperH VOU video output driver"
 	depends on MEDIA_CAMERA_SUPPORT
drivers/media/platform/Makefile +1 -0
index 6ab6200..2973953 100644
@@ -3,6 +3,7 @@
 # Makefile for the video capture/playback device drivers.
 #
 
+obj-$(CONFIG_VIDEO_ASPEED)		+= aspeed-video.o
 obj-$(CONFIG_VIDEO_CADENCE)		+= cadence/
 obj-$(CONFIG_VIDEO_VIA_CAMERA) += via-camera.o
 obj-$(CONFIG_VIDEO_CAFE_CCIC) += marvell-ccic/
drivers/media/platform/aspeed-video.c new file +1711 -0

1,711 lines not on this page · raw message

Signature · 1 line
1.8.3.1
#3 lore raw

Re: [PATCH v5 2/2] media: platform: Add Aspeed Video Engine driver

Quoted 278 lines · Eddie James

The Video Engine (VE) embedded in the Aspeed AST2400 and AST2500 SOCs can capture and compress video data from digital or analog sources. With the Aspeed chip acting a service processor, the Video Engine can capture the host processor graphics output.

Add a V4L2 driver to capture video data and compress it to JPEG images. Make the video frames available through the V4L2 streaming interface.

---
 MAINTAINERS                           |    8 +
 drivers/media/platform/Kconfig        |    9 +
 drivers/media/platform/Makefile       |    1 +
 drivers/media/platform/aspeed-video.c | 1711 +++++++++++++++++++++++++++++++++
 4 files changed, 1729 insertions(+)
 create mode 100644 drivers/media/platform/aspeed-video.c
MAINTAINERS +8 -0
index fa45ff3..f8f08a4 100644
@@ -2414,6 +2414,14 @@ S:	Maintained
 F:	Documentation/hwmon/asc7621
 F:	drivers/hwmon/asc7621.c
 
+ASPEED VIDEO ENGINE DRIVER
+M:	Eddie James <[email protected]>
+L:	linux-media at vger.kernel.org
+L:	openbmc at lists.ozlabs.org (moderated for non-subscribers)
+S:	Maintained
+F:	drivers/media/platform/aspeed-video.c
+F:	Documentation/devicetree/bindings/media/aspeed-video.txt
+
 ASUS NOTEBOOKS AND EEEPC ACPI/WMI EXTRAS DRIVERS
 M:	Corentin Chary <[email protected]>
 L:	acpi4asus-user at lists.sourceforge.net
drivers/media/platform/Kconfig +9 -0
index 70c4f6c..ba78dd5 100644
@@ -32,6 +32,15 @@ source "drivers/media/platform/davinci/Kconfig"
 
 source "drivers/media/platform/omap/Kconfig"
 
+config VIDEO_ASPEED
+	tristate "Aspeed AST2400 and AST2500 Video Engine driver"
+	depends on VIDEO_V4L2
+	select VIDEOBUF2_DMA_CONTIG
+	help
+	  Support for the Aspeed Video Engine (VE) embedded in the Aspeed
+	  AST2400 and AST2500 SOCs. The VE can capture and compress video data
+	  from digital or analog sources.
+
 config VIDEO_SH_VOU
 	tristate "SuperH VOU video output driver"
 	depends on MEDIA_CAMERA_SUPPORT
drivers/media/platform/Makefile +1 -0
index 6ab6200..2973953 100644
@@ -3,6 +3,7 @@
 # Makefile for the video capture/playback device drivers.
 #
 
+obj-$(CONFIG_VIDEO_ASPEED)		+= aspeed-video.o
 obj-$(CONFIG_VIDEO_CADENCE)		+= cadence/
 obj-$(CONFIG_VIDEO_VIA_CAMERA) += via-camera.o
 obj-$(CONFIG_VIDEO_CAFE_CCIC) += marvell-ccic/
drivers/media/platform/aspeed-video.c new file +204 -0
new file mode 100644
index 0000000..a2fd0bf
@@ -0,0 +1,1711 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <linux/atomic.h>
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/interrupt.h>
+#include <linux/jiffies.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+#include <linux/sched.h>
+#include <linux/spinlock.h>
+#include <linux/string.h>
+#include <linux/v4l2-controls.h>
+#include <linux/videodev2.h>
+#include <linux/wait.h>
+#include <linux/workqueue.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-dev.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-ioctl.h>
+#include <media/videobuf2-dma-contig.h>
+
+#define DEVICE_NAME			"aspeed-video"
+
+#define ASPEED_VIDEO_JPEG_NUM_QUALITIES	12
+#define ASPEED_VIDEO_JPEG_HEADER_SIZE	10
+#define ASPEED_VIDEO_JPEG_QUANT_SIZE	116
+#define ASPEED_VIDEO_JPEG_DCT_SIZE	34
+
+#define MAX_FRAME_RATE			60
+#define MAX_HEIGHT			1200
+#define MAX_WIDTH			1920
+#define MIN_HEIGHT			480
+#define MIN_WIDTH			640
+
+#define NUM_POLARITY_CHECKS		10
+#define INVALID_RESOLUTION_RETRIES	2
+#define INVALID_RESOLUTION_DELAY	msecs_to_jiffies(250)
+#define RESOLUTION_CHANGE_DELAY		msecs_to_jiffies(500)
+#define MODE_DETECT_TIMEOUT		msecs_to_jiffies(500)
+#define STOP_TIMEOUT			msecs_to_jiffies(250)
+#define DIRECT_FETCH_THRESHOLD		0x0c0000 /* 1024 * 768 */
+
+#define VE_MAX_SRC_BUFFER_SIZE		0x8ca000 /* 1920 * 1200, 32bpp */
+#define VE_JPEG_HEADER_SIZE		0x006000 /* 512 * 12 * 4 */
+
+#define VE_PROTECTION_KEY		0x000
+#define  VE_PROTECTION_KEY_UNLOCK	0x1a038aa8
+
+#define VE_SEQ_CTRL			0x004
+#define  VE_SEQ_CTRL_TRIG_MODE_DET	BIT(0)
+#define  VE_SEQ_CTRL_TRIG_CAPTURE	BIT(1)
+#define  VE_SEQ_CTRL_FORCE_IDLE		BIT(2)
+#define  VE_SEQ_CTRL_MULT_FRAME		BIT(3)
+#define  VE_SEQ_CTRL_TRIG_COMP		BIT(4)
+#define  VE_SEQ_CTRL_AUTO_COMP		BIT(5)
+#define  VE_SEQ_CTRL_EN_WATCHDOG	BIT(7)
+#define  VE_SEQ_CTRL_YUV420		BIT(10)
+#define  VE_SEQ_CTRL_COMP_FMT		GENMASK(11, 10)
+#define  VE_SEQ_CTRL_HALT		BIT(12)
+#define  VE_SEQ_CTRL_EN_WATCHDOG_COMP	BIT(14)
+#define  VE_SEQ_CTRL_TRIG_JPG		BIT(15)
+#define  VE_SEQ_CTRL_CAP_BUSY		BIT(16)
+#define  VE_SEQ_CTRL_COMP_BUSY		BIT(18)
+
+#ifdef CONFIG_MACH_ASPEED_G5
+#define  VE_SEQ_CTRL_JPEG_MODE		BIT(13)	/* AST2500 */
+#else
+#define  VE_SEQ_CTRL_JPEG_MODE		BIT(8)	/* AST2400 */
+#endif /* CONFIG_MACH_ASPEED_G5 */
+
+#define VE_CTRL				0x008
+#define  VE_CTRL_HSYNC_POL		BIT(0)
+#define  VE_CTRL_VSYNC_POL		BIT(1)
+#define  VE_CTRL_SOURCE			BIT(2)
+#define  VE_CTRL_INT_DE			BIT(4)
+#define  VE_CTRL_DIRECT_FETCH		BIT(5)
+#define  VE_CTRL_YUV			BIT(6)
+#define  VE_CTRL_RGB			BIT(7)
+#define  VE_CTRL_CAPTURE_FMT		GENMASK(7, 6)
+#define  VE_CTRL_AUTO_OR_CURSOR		BIT(8)
+#define  VE_CTRL_CLK_INVERSE		BIT(11)
+#define  VE_CTRL_CLK_DELAY		GENMASK(11, 9)
+#define  VE_CTRL_INTERLACE		BIT(14)
+#define  VE_CTRL_HSYNC_POL_CTRL		BIT(15)
+#define  VE_CTRL_FRC			GENMASK(23, 16)
+
+#define VE_TGS_0			0x00c
+#define VE_TGS_1			0x010
+#define  VE_TGS_FIRST			GENMASK(28, 16)
+#define  VE_TGS_LAST			GENMASK(12, 0)
+
+#define VE_SCALING_FACTOR		0x014
+#define VE_SCALING_FILTER0		0x018
+#define VE_SCALING_FILTER1		0x01c
+#define VE_SCALING_FILTER2		0x020
+#define VE_SCALING_FILTER3		0x024
+
+#define VE_CAP_WINDOW			0x030
+#define VE_COMP_WINDOW			0x034
+#define VE_COMP_PROC_OFFSET		0x038
+#define VE_COMP_OFFSET			0x03c
+#define VE_JPEG_ADDR			0x040
+#define VE_SRC0_ADDR			0x044
+#define VE_SRC_SCANLINE_OFFSET		0x048
+#define VE_SRC1_ADDR			0x04c
+#define VE_COMP_ADDR			0x054
+
+#define VE_STREAM_BUF_SIZE		0x058
+#define  VE_STREAM_BUF_SIZE_N_PACKETS	GENMASK(5, 3)
+#define  VE_STREAM_BUF_SIZE_P_SIZE	GENMASK(2, 0)
+
+#define VE_COMP_CTRL			0x060
+#define  VE_COMP_CTRL_VQ_DCT_ONLY	BIT(0)
+#define  VE_COMP_CTRL_VQ_4COLOR		BIT(1)
+#define  VE_COMP_CTRL_QUANTIZE		BIT(2)
+#define  VE_COMP_CTRL_EN_BQ		BIT(4)
+#define  VE_COMP_CTRL_EN_CRYPTO		BIT(5)
+#define  VE_COMP_CTRL_DCT_CHR		GENMASK(10, 6)
+#define  VE_COMP_CTRL_DCT_LUM		GENMASK(15, 11)
+#define  VE_COMP_CTRL_EN_HQ		BIT(16)
+#define  VE_COMP_CTRL_RSVD		BIT(19)
+#define  VE_COMP_CTRL_ENCODE		GENMASK(21, 20)
+#define  VE_COMP_CTRL_HQ_DCT_CHR	GENMASK(26, 22)
+#define  VE_COMP_CTRL_HQ_DCT_LUM	GENMASK(31, 27)
+
+#define VE_OFFSET_COMP_STREAM		0x078
+
+#define VE_SRC_LR_EDGE_DET		0x090
+#define  VE_SRC_LR_EDGE_DET_LEFT	GENMASK(11, 0)
+#define  VE_SRC_LR_EDGE_DET_NO_V	BIT(12)
+#define  VE_SRC_LR_EDGE_DET_NO_H	BIT(13)
+#define  VE_SRC_LR_EDGE_DET_NO_DISP	BIT(14)
+#define  VE_SRC_LR_EDGE_DET_NO_CLK	BIT(15)
+#define  VE_SRC_LR_EDGE_DET_RT_SHF	16
+#define  VE_SRC_LR_EDGE_DET_RT		GENMASK(27, VE_SRC_LR_EDGE_DET_RT_SHF)
+#define  VE_SRC_LR_EDGE_DET_INTERLACE	BIT(31)
+
+#define VE_SRC_TB_EDGE_DET		0x094
+#define  VE_SRC_TB_EDGE_DET_TOP		GENMASK(12, 0)
+#define  VE_SRC_TB_EDGE_DET_BOT_SHF	16
+#define  VE_SRC_TB_EDGE_DET_BOT		GENMASK(28, VE_SRC_TB_EDGE_DET_BOT_SHF)
+
+#define VE_MODE_DETECT_STATUS		0x098
+#define  VE_MODE_DETECT_H_PIXELS	GENMASK(11, 0)
+#define  VE_MODE_DETECT_V_LINES_SHF	16
+#define  VE_MODE_DETECT_V_LINES		GENMASK(27, VE_MODE_DETECT_V_LINES_SHF)
+#define  VE_MODE_DETECT_STATUS_VSYNC	BIT(28)
+#define  VE_MODE_DETECT_STATUS_HSYNC	BIT(29)
+
+#define VE_SYNC_STATUS			0x09c
+#define  VE_SYNC_STATUS_HSYNC		GENMASK(11, 0)
+#define  VE_SYNC_STATUS_VSYNC_SHF	16
+#define  VE_SYNC_STATUS_VSYNC		GENMASK(27, VE_SYNC_STATUS_VSYNC_SHF)
+
+#define VE_INTERRUPT_CTRL		0x304
+#define VE_INTERRUPT_STATUS		0x308
+#define  VE_INTERRUPT_MODE_DETECT_WD	BIT(0)
+#define  VE_INTERRUPT_CAPTURE_COMPLETE	BIT(1)
+#define  VE_INTERRUPT_COMP_READY	BIT(2)
+#define  VE_INTERRUPT_COMP_COMPLETE	BIT(3)
+#define  VE_INTERRUPT_MODE_DETECT	BIT(4)
+#define  VE_INTERRUPT_FRAME_COMPLETE	BIT(5)
+#define  VE_INTERRUPT_DECODE_ERR	BIT(6)
+#define  VE_INTERRUPT_HALT_READY	BIT(8)
+#define  VE_INTERRUPT_HANG_WD		BIT(9)
+#define  VE_INTERRUPT_STREAM_DESC	BIT(10)
+#define  VE_INTERRUPT_VSYNC_DESC	BIT(11)
+
+#define VE_MODE_DETECT			0x30c
+#define VE_MEM_RESTRICT_START		0x310
+#define VE_MEM_RESTRICT_END		0x314
+
+enum {
+	VIDEO_MODE_DETECT_DONE,
+	VIDEO_RES_CHANGE,
+	VIDEO_STREAMING,
+	VIDEO_FRAME_INPRG,
+};
+
+struct aspeed_video_addr {
+	unsigned int size;
+	dma_addr_t dma;
+	void *virt;
+};
+
+struct aspeed_video_buffer {
+	struct vb2_v4l2_buffer vb;
+	struct list_head link;
+};
+
+#define to_aspeed_video_buffer(x) \
+	container_of((x), struct aspeed_video_buffer, vb)
+
+struct aspeed_video {

drivers/media/platform/aspeed-video.c line 214

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+	void __iomem *base;
+	struct clk *eclk;
+	struct clk *vclk;
+	struct reset_control *rst;
+
+	struct device *dev;
+	struct v4l2_ctrl_handler ctrl_handler;
+	struct v4l2_device v4l2_dev;
+	struct v4l2_pix_format pix_fmt;
+	struct v4l2_bt_timings timings;

You need two v4l2_bt_timings structs here:

	struct v4l2_bt_timings active_timings;
	struct v4l2_bt_timings detected_timings;

The first is what s_dv_timings set (and must also be initialized to some timing at probe time), the second is what aspeed_video_get_resolution fills in.

See more about this below.

Quoted 242 lines
drivers/media/platform/aspeed-video.c new file +242 -0
+	struct vb2_queue queue;
+	struct video_device vdev;
+	struct mutex video_lock;
+
+	atomic_t clients;
+	wait_queue_head_t wait;
+	spinlock_t lock;
+	struct delayed_work res_work;
+	struct list_head buffers;
+	unsigned long flags;
+	unsigned int sequence;
+
+	unsigned int max_compressed_size;
+	struct aspeed_video_addr srcs[2];
+	struct aspeed_video_addr jpeg;
+	struct aspeed_video_addr detect;
+
+	bool yuv420;
+	unsigned int frame_rate;
+	unsigned int jpeg_quality;
+	unsigned int capture_height;
+	unsigned int capture_width;
+};
+
+#define to_aspeed_video(x) container_of((x), struct aspeed_video, v4l2_dev)
+
+static const u32 aspeed_video_jpeg_header[ASPEED_VIDEO_JPEG_HEADER_SIZE] = {
+	0xe0ffd8ff, 0x464a1000, 0x01004649, 0x60000101, 0x00006000, 0x0f00feff,
+	0x00002d05, 0x00000000, 0x00000000, 0x00dbff00
+};
+
+static const u32 aspeed_video_jpeg_quant[ASPEED_VIDEO_JPEG_QUANT_SIZE] = {
+	0x081100c0, 0x00000000, 0x00110103, 0x03011102, 0xc4ff0111, 0x00001f00,
+	0x01010501, 0x01010101, 0x00000000, 0x00000000, 0x04030201, 0x08070605,
+	0xff0b0a09, 0x10b500c4, 0x03010200, 0x03040203, 0x04040505, 0x7d010000,
+	0x00030201, 0x12051104, 0x06413121, 0x07615113, 0x32147122, 0x08a19181,
+	0xc1b14223, 0xf0d15215, 0x72623324, 0x160a0982, 0x1a191817, 0x28272625,
+	0x35342a29, 0x39383736, 0x4544433a, 0x49484746, 0x5554534a, 0x59585756,
+	0x6564635a, 0x69686766, 0x7574736a, 0x79787776, 0x8584837a, 0x89888786,
+	0x9493928a, 0x98979695, 0xa3a29a99, 0xa7a6a5a4, 0xb2aaa9a8, 0xb6b5b4b3,
+	0xbab9b8b7, 0xc5c4c3c2, 0xc9c8c7c6, 0xd4d3d2ca, 0xd8d7d6d5, 0xe2e1dad9,
+	0xe6e5e4e3, 0xeae9e8e7, 0xf4f3f2f1, 0xf8f7f6f5, 0xc4fffaf9, 0x00011f00,
+	0x01010103, 0x01010101, 0x00000101, 0x00000000, 0x04030201, 0x08070605,
+	0xff0b0a09, 0x11b500c4, 0x02010200, 0x04030404, 0x04040507, 0x77020100,
+	0x03020100, 0x21050411, 0x41120631, 0x71610751, 0x81322213, 0x91421408,
+	0x09c1b1a1, 0xf0523323, 0xd1726215, 0x3424160a, 0x17f125e1, 0x261a1918,
+	0x2a292827, 0x38373635, 0x44433a39, 0x48474645, 0x54534a49, 0x58575655,
+	0x64635a59, 0x68676665, 0x74736a69, 0x78777675, 0x83827a79, 0x87868584,
+	0x928a8988, 0x96959493, 0x9a999897, 0xa5a4a3a2, 0xa9a8a7a6, 0xb4b3b2aa,
+	0xb8b7b6b5, 0xc3c2bab9, 0xc7c6c5c4, 0xd2cac9c8, 0xd6d5d4d3, 0xdad9d8d7,
+	0xe5e4e3e2, 0xe9e8e7e6, 0xf4f3f2ea, 0xf8f7f6f5, 0xdafffaf9, 0x01030c00,
+	0x03110200, 0x003f0011
+};
+
+static const u32 aspeed_video_jpeg_dct[ASPEED_VIDEO_JPEG_NUM_QUALITIES]
+				      [ASPEED_VIDEO_JPEG_DCT_SIZE] = {
+	{ 0x0d140043, 0x0c0f110f, 0x11101114, 0x17141516, 0x1e20321e,
+	  0x3d1e1b1b, 0x32242e2b, 0x4b4c3f48, 0x44463f47, 0x61735a50,
+	  0x566c5550, 0x88644644, 0x7a766c65, 0x4d808280, 0x8c978d60,
+	  0x7e73967d, 0xdbff7b80, 0x1f014300, 0x272d2121, 0x3030582d,
+	  0x697bb958, 0xb8b9b97b, 0xb9b8a6a6, 0xb9b9b9b9, 0xb9b9b9b9,
+	  0xb9b9b9b9, 0xb9b9b9b9, 0xb9b9b9b9, 0xb9b9b9b9, 0xb9b9b9b9,
+	  0xb9b9b9b9, 0xb9b9b9b9, 0xb9b9b9b9, 0xffb9b9b9 },
+	{ 0x0c110043, 0x0a0d0f0d, 0x0f0e0f11, 0x14111213, 0x1a1c2b1a,
+	  0x351a1818, 0x2b1f2826, 0x4142373f, 0x3c3d373e, 0x55644e46,
+	  0x4b5f4a46, 0x77573d3c, 0x6b675f58, 0x43707170, 0x7a847b54,
+	  0x6e64836d, 0xdbff6c70, 0x1b014300, 0x22271d1d, 0x2a2a4c27,
+	  0x5b6ba04c, 0xa0a0a06b, 0xa0a0a0a0, 0xa0a0a0a0, 0xa0a0a0a0,
+	  0xa0a0a0a0, 0xa0a0a0a0, 0xa0a0a0a0, 0xa0a0a0a0, 0xa0a0a0a0,
+	  0xa0a0a0a0, 0xa0a0a0a0, 0xa0a0a0a0, 0xffa0a0a0 },
+	{ 0x090e0043, 0x090a0c0a, 0x0c0b0c0e, 0x110e0f10, 0x15172415,
+	  0x2c151313, 0x241a211f, 0x36372e34, 0x31322e33, 0x4653413a,
+	  0x3e4e3d3a, 0x62483231, 0x58564e49, 0x385d5e5d, 0x656d6645,
+	  0x5b536c5a, 0xdbff595d, 0x16014300, 0x1c201818, 0x22223f20,
+	  0x4b58853f, 0x85858558, 0x85858585, 0x85858585, 0x85858585,
+	  0x85858585, 0x85858585, 0x85858585, 0x85858585, 0x85858585,
+	  0x85858585, 0x85858585, 0x85858585, 0xff858585 },
+	{ 0x070b0043, 0x07080a08, 0x0a090a0b, 0x0d0b0c0c, 0x11121c11,
+	  0x23110f0f, 0x1c141a19, 0x2b2b2429, 0x27282428, 0x3842332e,
+	  0x313e302e, 0x4e392827, 0x46443e3a, 0x2c4a4a4a, 0x50565137,
+	  0x48425647, 0xdbff474a, 0x12014300, 0x161a1313, 0x1c1c331a,
+	  0x3d486c33, 0x6c6c6c48, 0x6c6c6c6c, 0x6c6c6c6c, 0x6c6c6c6c,
+	  0x6c6c6c6c, 0x6c6c6c6c, 0x6c6c6c6c, 0x6c6c6c6c, 0x6c6c6c6c,
+	  0x6c6c6c6c, 0x6c6c6c6c, 0x6c6c6c6c, 0xff6c6c6c },
+	{ 0x06090043, 0x05060706, 0x07070709, 0x0a09090a, 0x0d0e160d,
+	  0x1b0d0c0c, 0x16101413, 0x21221c20, 0x1e1f1c20, 0x2b332824,
+	  0x26302624, 0x3d2d1f1e, 0x3735302d, 0x22393a39, 0x3f443f2b,
+	  0x38334338, 0xdbff3739, 0x0d014300, 0x11130e0e, 0x15152613,
+	  0x2d355026, 0x50505035, 0x50505050, 0x50505050, 0x50505050,
+	  0x50505050, 0x50505050, 0x50505050, 0x50505050, 0x50505050,
+	  0x50505050, 0x50505050, 0x50505050, 0xff505050 },
+	{ 0x04060043, 0x03040504, 0x05040506, 0x07060606, 0x09090f09,
+	  0x12090808, 0x0f0a0d0d, 0x16161315, 0x14151315, 0x1d221b18,
+	  0x19201918, 0x281e1514, 0x2423201e, 0x17262726, 0x2a2d2a1c,
+	  0x25222d25, 0xdbff2526, 0x09014300, 0x0b0d0a0a, 0x0e0e1a0d,
+	  0x1f25371a, 0x37373725, 0x37373737, 0x37373737, 0x37373737,
+	  0x37373737, 0x37373737, 0x37373737, 0x37373737, 0x37373737,
+	  0x37373737, 0x37373737, 0x37373737, 0xff373737 },
+	{ 0x02030043, 0x01020202, 0x02020203, 0x03030303, 0x04040704,
+	  0x09040404, 0x07050606, 0x0b0b090a, 0x0a0a090a, 0x0e110d0c,
+	  0x0c100c0c, 0x140f0a0a, 0x1211100f, 0x0b131313, 0x1516150e,
+	  0x12111612, 0xdbff1213, 0x04014300, 0x05060505, 0x07070d06,
+	  0x0f121b0d, 0x1b1b1b12, 0x1b1b1b1b, 0x1b1b1b1b, 0x1b1b1b1b,
+	  0x1b1b1b1b, 0x1b1b1b1b, 0x1b1b1b1b, 0x1b1b1b1b, 0x1b1b1b1b,
+	  0x1b1b1b1b, 0x1b1b1b1b, 0x1b1b1b1b, 0xff1b1b1b },
+	{ 0x01020043, 0x01010101, 0x01010102, 0x02020202, 0x03030503,
+	  0x06030202, 0x05030404, 0x07070607, 0x06070607, 0x090b0908,
+	  0x080a0808, 0x0d0a0706, 0x0c0b0a0a, 0x070c0d0c, 0x0e0f0e09,
+	  0x0c0b0f0c, 0xdbff0c0c, 0x03014300, 0x03040303, 0x04040804,
+	  0x0a0c1208, 0x1212120c, 0x12121212, 0x12121212, 0x12121212,
+	  0x12121212, 0x12121212, 0x12121212, 0x12121212, 0x12121212,
+	  0x12121212, 0x12121212, 0x12121212, 0xff121212 },
+	{ 0x01020043, 0x01010101, 0x01010102, 0x02020202, 0x03030503,
+	  0x06030202, 0x05030404, 0x07070607, 0x06070607, 0x090b0908,
+	  0x080a0808, 0x0d0a0706, 0x0c0b0a0a, 0x070c0d0c, 0x0e0f0e09,
+	  0x0c0b0f0c, 0xdbff0c0c, 0x02014300, 0x03030202, 0x04040703,
+	  0x080a0f07, 0x0f0f0f0a, 0x0f0f0f0f, 0x0f0f0f0f, 0x0f0f0f0f,
+	  0x0f0f0f0f, 0x0f0f0f0f, 0x0f0f0f0f, 0x0f0f0f0f, 0x0f0f0f0f,
+	  0x0f0f0f0f, 0x0f0f0f0f, 0x0f0f0f0f, 0xff0f0f0f },
+	{ 0x01010043, 0x01010101, 0x01010101, 0x01010101, 0x02020302,
+	  0x04020202, 0x03020303, 0x05050405, 0x05050405, 0x07080606,
+	  0x06080606, 0x0a070505, 0x09080807, 0x05090909, 0x0a0b0a07,
+	  0x09080b09, 0xdbff0909, 0x02014300, 0x02030202, 0x03030503,
+	  0x07080c05, 0x0c0c0c08, 0x0c0c0c0c, 0x0c0c0c0c, 0x0c0c0c0c,
+	  0x0c0c0c0c, 0x0c0c0c0c, 0x0c0c0c0c, 0x0c0c0c0c, 0x0c0c0c0c,
+	  0x0c0c0c0c, 0x0c0c0c0c, 0x0c0c0c0c, 0xff0c0c0c },
+	{ 0x01010043, 0x01010101, 0x01010101, 0x01010101, 0x01010201,
+	  0x03010101, 0x02010202, 0x03030303, 0x03030303, 0x04050404,
+	  0x04050404, 0x06050303, 0x06050505, 0x03060606, 0x07070704,
+	  0x06050706, 0xdbff0606, 0x01014300, 0x01020101, 0x02020402,
+	  0x05060904, 0x09090906, 0x09090909, 0x09090909, 0x09090909,
+	  0x09090909, 0x09090909, 0x09090909, 0x09090909, 0x09090909,
+	  0x09090909, 0x09090909, 0x09090909, 0xff090909 },
+	{ 0x01010043, 0x01010101, 0x01010101, 0x01010101, 0x01010101,
+	  0x01010101, 0x01010101, 0x01010101, 0x01010101, 0x02020202,
+	  0x02020202, 0x03020101, 0x03020202, 0x01030303, 0x03030302,
+	  0x03020303, 0xdbff0403, 0x01014300, 0x01010101, 0x01010201,
+	  0x03040602, 0x06060604, 0x06060606, 0x06060606, 0x06060606,
+	  0x06060606, 0x06060606, 0x06060606, 0x06060606, 0x06060606,
+	  0x06060606, 0x06060606, 0x06060606, 0xff060606 }
+};
+
+static void aspeed_video_init_jpeg_table(u32 *table, bool yuv420)
+{
+	int i;
+	unsigned int base;
+
+	for (i = 0; i < ASPEED_VIDEO_JPEG_NUM_QUALITIES; i++) {
+		base = 256 * i;	/* AST HW requires this header spacing */
+		memcpy(&table[base], aspeed_video_jpeg_header,
+		       sizeof(aspeed_video_jpeg_header));
+
+		base += ASPEED_VIDEO_JPEG_HEADER_SIZE;
+		memcpy(&table[base], aspeed_video_jpeg_dct[i],
+		       sizeof(aspeed_video_jpeg_dct[i]));
+
+		base += ASPEED_VIDEO_JPEG_DCT_SIZE;
+		memcpy(&table[base], aspeed_video_jpeg_quant,
+		       sizeof(aspeed_video_jpeg_quant));
+
+		if (yuv420)
+			table[base + 2] = 0x00220103;
+	}
+}
+
+static void aspeed_video_update(struct aspeed_video *video, u32 reg, u32 clear,
+				u32 bits)
+{
+	u32 t = readl(video->base + reg);
+	u32 before = t;
+
+	t &= ~clear;
+	t |= bits;
+	writel(t, video->base + reg);
+	dev_dbg(video->dev, "update %03x[%08x -> %08x]\n", reg, before,
+		readl(video->base + reg));
+}
+
+static u32 aspeed_video_read(struct aspeed_video *video, u32 reg)
+{
+	u32 t = readl(video->base + reg);
+
+	dev_dbg(video->dev, "read %03x[%08x]\n", reg, t);
+	return t;
+}
+
+static void aspeed_video_write(struct aspeed_video *video, u32 reg, u32 val)
+{
+	writel(val, video->base + reg);
+	dev_dbg(video->dev, "write %03x[%08x]\n", reg,
+		readl(video->base + reg));
+}
+
+static bool aspeed_video_engine_busy(struct aspeed_video *video)
+{
+	u32 seq_ctrl = aspeed_video_read(video, VE_SEQ_CTRL);
+
+	if (!(seq_ctrl & VE_SEQ_CTRL_COMP_BUSY) ||
+	    !(seq_ctrl & VE_SEQ_CTRL_CAP_BUSY)) {
+		dev_err(video->dev, "video engine busy\n");
+		return true;
+	}
+
+	return false;
+}
+
+static int aspeed_video_start_frame(struct aspeed_video *video)
+{
+	dma_addr_t addr;
+	unsigned long flags;
+	struct aspeed_video_buffer *buf;
+
+	if (aspeed_video_engine_busy(video))
+		return -EBUSY;
+
+	spin_lock_irqsave(&video->lock, flags);
+	buf = list_first_entry_or_null(&video->buffers,
+				       struct aspeed_video_buffer, link);
+	if (!buf) {
+		spin_unlock_irqrestore(&video->lock, flags);
+		return -EPROTO;
+	}
+
+	set_bit(VIDEO_FRAME_INPRG, &video->flags);
+	addr = vb2_dma_contig_plane_dma_addr(&buf->vb.vb2_buf, 0);
+	spin_unlock_irqrestore(&video->lock, flags);
+
+	aspeed_video_write(video, VE_COMP_PROC_OFFSET, 0);
+	aspeed_video_write(video, VE_COMP_OFFSET, 0);
+	aspeed_video_write(video, VE_COMP_ADDR, addr);
+
+	aspeed_video_update(video, VE_INTERRUPT_CTRL, 0,
+			    VE_INTERRUPT_COMP_COMPLETE |
+			    VE_INTERRUPT_CAPTURE_COMPLETE);
+
+	aspeed_video_update(video, VE_SEQ_CTRL, 0,
+			    VE_SEQ_CTRL_TRIG_CAPTURE | VE_SEQ_CTRL_TRIG_COMP);
+
+	return 0;
+}
+
+static void aspeed_video_start_mode_detect(struct aspeed_video *video)

drivers/media/platform/aspeed-video.c line 466

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+{
+	/* Enable mode detect interrupts */
+	aspeed_video_update(video, VE_INTERRUPT_CTRL, 0,
+			    VE_INTERRUPT_MODE_DETECT);
+
+	/* Trigger mode detect */
+	aspeed_video_update(video, VE_SEQ_CTRL, 0, VE_SEQ_CTRL_TRIG_MODE_DET);
+}
+
+static void aspeed_video_disable_mode_detect(struct aspeed_video *video)

Somewhat weird naming for this pair of functions: either use start/stop or enable/disable (my preference), not start/disable.

Quoted 33 lines
drivers/media/platform/aspeed-video.c new file +33 -0
+{
+	/* Disable mode detect interrupts */
+	aspeed_video_update(video, VE_INTERRUPT_CTRL,
+			    VE_INTERRUPT_MODE_DETECT, 0);
+
+	/* Disable mode detect */
+	aspeed_video_update(video, VE_SEQ_CTRL, VE_SEQ_CTRL_TRIG_MODE_DET, 0);
+}
+
+static void aspeed_video_off(struct aspeed_video *video)
+{
+	/* Reset the engine */
+	reset_control_assert(video->rst);
+	udelay(100);
+	reset_control_deassert(video->rst);
+
+	/* Turn off the relevant clocks */
+	clk_disable_unprepare(video->vclk);
+	clk_disable_unprepare(video->eclk);
+}
+
+static void aspeed_video_on(struct aspeed_video *video)
+{
+	/* Turn on the relevant clocks */
+	clk_prepare_enable(video->eclk);
+	clk_prepare_enable(video->vclk);
+
+	/* Reset the engine */
+	reset_control_assert(video->rst);
+	udelay(100);
+	reset_control_deassert(video->rst);
+}
+

drivers/media/platform/aspeed-video.c line 509

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+static void aspeed_video_bufs_done(struct aspeed_video *video,
+				   enum vb2_buffer_state state)
+{
+	unsigned long flags;
+	struct aspeed_video_buffer *buf;
+
+	spin_lock_irqsave(&video->lock, flags);
+	list_for_each_entry(buf, &video->buffers, link) {
+		if (list_is_last(&buf->link, &video->buffers))
+			buf->vb.flags |= V4L2_BUF_FLAG_LAST;

You don't need to use this flag. It's meant for hardware codecs, not for a regular video capture driver.

Quoted 78 lines
drivers/media/platform/aspeed-video.c new file +78 -0
+		vb2_buffer_done(&buf->vb.vb2_buf, state);
+	}
+	INIT_LIST_HEAD(&video->buffers);
+	spin_unlock_irqrestore(&video->lock, flags);
+}
+
+static irqreturn_t aspeed_video_irq(int irq, void *arg)
+{
+	struct aspeed_video *video = arg;
+	u32 sts = aspeed_video_read(video, VE_INTERRUPT_STATUS);
+
+	if (atomic_read(&video->clients) == 0) {
+		dev_info(video->dev, "irq with no client; disabling irqs\n");
+
+		aspeed_video_write(video, VE_INTERRUPT_CTRL, 0);
+		aspeed_video_write(video, VE_INTERRUPT_STATUS, 0xffffffff);
+		return IRQ_HANDLED;
+	}
+
+	/* Resolution changed; reset entire engine and reinitialize */
+	if (sts & VE_INTERRUPT_MODE_DETECT_WD) {
+		dev_info(video->dev, "resolution changed; resetting\n");
+		set_bit(VIDEO_RES_CHANGE, &video->flags);
+		clear_bit(VIDEO_FRAME_INPRG, &video->flags);
+		clear_bit(VIDEO_STREAMING, &video->flags);
+
+		aspeed_video_off(video);
+		aspeed_video_bufs_done(video, VB2_BUF_STATE_ERROR);
+
+		schedule_delayed_work(&video->res_work,
+				      RESOLUTION_CHANGE_DELAY);
+		return IRQ_HANDLED;
+	}
+
+	if (sts & VE_INTERRUPT_MODE_DETECT) {
+		aspeed_video_update(video, VE_INTERRUPT_CTRL,
+				    VE_INTERRUPT_MODE_DETECT, 0);
+		aspeed_video_write(video, VE_INTERRUPT_STATUS,
+				   VE_INTERRUPT_MODE_DETECT);
+
+		set_bit(VIDEO_MODE_DETECT_DONE, &video->flags);
+		wake_up_interruptible_all(&video->wait);
+	}
+
+	if ((sts & VE_INTERRUPT_COMP_COMPLETE) &&
+	    (sts & VE_INTERRUPT_CAPTURE_COMPLETE)) {
+		struct aspeed_video_buffer *buf;
+		u32 frame_size = aspeed_video_read(video,
+						   VE_OFFSET_COMP_STREAM);
+
+		spin_lock(&video->lock);
+		clear_bit(VIDEO_FRAME_INPRG, &video->flags);
+		buf = list_first_entry_or_null(&video->buffers,
+					       struct aspeed_video_buffer,
+					       link);
+		if (buf) {
+			vb2_set_plane_payload(&buf->vb.vb2_buf, 0, frame_size);
+
+			if (!list_is_last(&buf->link, &video->buffers)) {
+				buf->vb.vb2_buf.timestamp = ktime_get_ns();
+				buf->vb.sequence = video->sequence++;
+				buf->vb.field = V4L2_FIELD_NONE;
+				vb2_buffer_done(&buf->vb.vb2_buf,
+						VB2_BUF_STATE_DONE);
+				list_del(&buf->link);
+			}
+		}
+		spin_unlock(&video->lock);
+
+		aspeed_video_update(video, VE_SEQ_CTRL,
+				    VE_SEQ_CTRL_TRIG_CAPTURE |
+				    VE_SEQ_CTRL_FORCE_IDLE |
+				    VE_SEQ_CTRL_TRIG_COMP, 0);
+		aspeed_video_update(video, VE_INTERRUPT_CTRL,
+				    VE_INTERRUPT_COMP_COMPLETE |
+				    VE_INTERRUPT_CAPTURE_COMPLETE, 0);
+		aspeed_video_write(video, VE_INTERRUPT_STATUS,
+				   VE_INTERRUPT_COMP_COMPLETE |

drivers/media/platform/aspeed-video.c line 597

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+				   VE_INTERRUPT_CAPTURE_COMPLETE);
+
+		if (test_bit(VIDEO_STREAMING, &video->flags) && buf)
+			aspeed_video_start_frame(video);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static void aspeed_video_check_polarity(struct aspeed_video *video)

This function should be moved to just before the get_resolution function, since that's the one that calls this.

Quoted 16 lines
drivers/media/platform/aspeed-video.c new file +16 -0
+{
+	int i;
+	int hsync_counter = 0;
+	int vsync_counter = 0;
+	u32 sts;
+
+	for (i = 0; i < NUM_POLARITY_CHECKS; ++i) {
+		sts = aspeed_video_read(video, VE_MODE_DETECT_STATUS);
+		if (sts & VE_MODE_DETECT_STATUS_VSYNC)
+			vsync_counter--;
+		else
+			vsync_counter++;
+
+		if (sts & VE_MODE_DETECT_STATUS_HSYNC)
+			hsync_counter--;
+		else

drivers/media/platform/aspeed-video.c line 623

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+			hsync_counter++;
+	}
+
+	if (hsync_counter < 0 || vsync_counter < 0) {
+		u32 ctrl;
+
+		if (hsync_counter < 0)
+			ctrl = VE_CTRL_HSYNC_POL;
+		else
+			video->timings.polarities |= V4L2_DV_HSYNC_POS_POL;

You should set this for video->detected_timings.
You also don't clear the polarities flag if the polarity is negative.

drivers/media/platform/aspeed-video.c line 630

Quoted 7 lines
drivers/media/platform/aspeed-video.c new file +7 -0
+
+		if (vsync_counter < 0)
+			ctrl = VE_CTRL_VSYNC_POL;
+		else
+			video->timings.polarities |= V4L2_DV_VSYNC_POS_POL;
+
+		aspeed_video_update(video, VE_CTRL, 0, ctrl);

It would make more sense to write to this register either when you start streaming or when s_dv_timings is called. That's when you need it, not when detecting a new timing.

Quoted 70 lines
drivers/media/platform/aspeed-video.c new file +70 -0
+	}
+}
+
+static bool aspeed_video_alloc_buf(struct aspeed_video *video,
+				   struct aspeed_video_addr *addr,
+				   unsigned int size)
+{
+	addr->virt = dma_alloc_coherent(video->dev, size, &addr->dma,
+					GFP_KERNEL);
+	if (!addr->virt)
+		return false;
+
+	addr->size = size;
+	return true;
+}
+
+static void aspeed_video_free_buf(struct aspeed_video *video,
+				  struct aspeed_video_addr *addr)
+{
+	dma_free_coherent(video->dev, addr->size, addr->virt, addr->dma);
+	addr->size = 0;
+	addr->dma = 0ULL;
+	addr->virt = NULL;
+}
+
+/*
+ * Get the minimum HW-supported compression buffer size for the frame size.
+ * Assume worst-case JPEG compression size is 1/8 raw size. This should be
+ * plenty even for maximum quality; any worse and the engine will simply return
+ * incomplete JPEGs.
+ */
+static void aspeed_video_calc_compressed_size(struct aspeed_video *video)
+{
+	int i, j;
+	u32 compression_buffer_size_reg = 0;
+	unsigned int size;
+	const unsigned int num_compression_packets = 4;
+	const unsigned int compression_packet_size = 1024;
+	const unsigned int max_compressed_size =
+		video->capture_width * video->capture_height / 2;
+
+	video->max_compressed_size = UINT_MAX;
+
+	for (i = 0; i < 6; ++i) {
+		for (j = 0; j < 8; ++j) {
+			size = (num_compression_packets << i) *
+				(compression_packet_size << j);
+			if (size < max_compressed_size)
+				continue;
+
+			if (size < video->max_compressed_size) {
+				compression_buffer_size_reg = (i << 3) | j;
+				video->max_compressed_size = size;
+			}
+		}
+	}
+
+	aspeed_video_write(video, VE_STREAM_BUF_SIZE,
+			   compression_buffer_size_reg);
+
+	dev_dbg(video->dev, "max compressed size: %x\n",
+		video->max_compressed_size);
+}
+
+#define res_check(v) test_and_clear_bit(VIDEO_MODE_DETECT_DONE, &(v)->flags)
+
+static int aspeed_video_get_resolution(struct aspeed_video *video)
+{
+	bool invalid_resolution = true;
+	int rc;

drivers/media/platform/aspeed-video.c line 710

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+	int tries = 0;
+	unsigned int bottom;
+	unsigned int left;
+	unsigned int right;
+	unsigned int top;
+	u32 mds;
+	u32 src_lr_edge;
+	u32 src_tb_edge;
+	u32 sync;
+

If I understand the code correctly, when this is called we're not supposed to be streaming video, right?

Quoted 17 lines
drivers/media/platform/aspeed-video.c new file +17 -0
+	if (video->srcs[1].size)
+		aspeed_video_free_buf(video, &video->srcs[1]);
+
+	if (!video->detect.size) {
+		if (video->srcs[0].size >= VE_MAX_SRC_BUFFER_SIZE) {
+			video->detect = video->srcs[0];
+
+			video->srcs[0].size = 0;
+			video->srcs[0].dma = 0ULL;
+			video->srcs[0].virt = NULL;
+		} else {
+			if (video->srcs[0].size)
+				aspeed_video_free_buf(video, &video->srcs[0]);
+
+			if (!aspeed_video_alloc_buf(video, &video->detect,
+						    VE_MAX_SRC_BUFFER_SIZE)) {
+				dev_err(video->dev,

drivers/media/platform/aspeed-video.c line 737

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+					"failed to allocate source buffers\n");
+				return -ENOMEM;
+			}
+		}
+	}
+
+	aspeed_video_write(video, VE_SRC0_ADDR, video->detect.dma);
+
+	video->timings.width = 0;
+	video->timings.height = 0;

detected_timings

Quoted 16 lines
drivers/media/platform/aspeed-video.c new file +16 -0
+
+	do {
+		if (tries) {
+			set_current_state(TASK_INTERRUPTIBLE);
+			if (schedule_timeout(INVALID_RESOLUTION_DELAY))
+				return -EINTR;
+		}
+
+		aspeed_video_start_mode_detect(video);
+
+		rc = wait_event_interruptible_timeout(video->wait,
+						      res_check(video),
+						      MODE_DETECT_TIMEOUT);
+		if (!rc) {
+			dev_err(video->dev, "timed out on 1st mode detect\n");
+			aspeed_video_disable_mode_detect(video);

drivers/media/platform/aspeed-video.c line 763

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+			return -ETIMEDOUT;
+		}
+
+		/* Disable mode detect in order to re-trigger */
+		aspeed_video_update(video, VE_SEQ_CTRL,
+				    VE_SEQ_CTRL_TRIG_MODE_DET, 0);
+
+		aspeed_video_check_polarity(video);
+
+		aspeed_video_start_mode_detect(video);

Just curious: why is check_polarity done before starting the mode_detect? I would expect it to be the other way around.

As mentioned above, aspeed_video_check_polarity doesn't just check the polarity, it also seems to set it. If this is required before you can do a mode detect, then that should be documented and the function should be renamed to check_and_set_polarity.

Quoted 49 lines
drivers/media/platform/aspeed-video.c new file +49 -0
+
+		rc = wait_event_interruptible_timeout(video->wait,
+						      res_check(video),
+						      MODE_DETECT_TIMEOUT);
+		if (!rc) {
+			dev_err(video->dev, "timed out on 2nd mode detect\n");
+			aspeed_video_disable_mode_detect(video);
+			return -ETIMEDOUT;
+		}
+
+		src_lr_edge = aspeed_video_read(video, VE_SRC_LR_EDGE_DET);
+		src_tb_edge = aspeed_video_read(video, VE_SRC_TB_EDGE_DET);
+		mds = aspeed_video_read(video, VE_MODE_DETECT_STATUS);
+		sync = aspeed_video_read(video, VE_SYNC_STATUS);
+
+		bottom = (src_tb_edge & VE_SRC_TB_EDGE_DET_BOT) >>
+			VE_SRC_TB_EDGE_DET_BOT_SHF;
+		top = src_tb_edge & VE_SRC_TB_EDGE_DET_TOP;
+		video->timings.vfrontporch = top;
+		video->timings.vbackporch = ((mds & VE_MODE_DETECT_V_LINES) >>
+			VE_MODE_DETECT_V_LINES_SHF) - bottom;
+		video->timings.vsync = (sync & VE_SYNC_STATUS_VSYNC) >>
+			VE_SYNC_STATUS_VSYNC_SHF;
+		if (top > bottom)
+			continue;
+
+		right = (src_lr_edge & VE_SRC_LR_EDGE_DET_RT) >>
+			VE_SRC_LR_EDGE_DET_RT_SHF;
+		left = src_lr_edge & VE_SRC_LR_EDGE_DET_LEFT;
+		video->timings.hfrontporch = left;
+		video->timings.hbackporch = (mds & VE_MODE_DETECT_H_PIXELS) -
+			right;
+		video->timings.hsync = sync & VE_SYNC_STATUS_HSYNC;
+		if (left > right)
+			continue;
+
+		invalid_resolution = false;
+	} while (invalid_resolution && (tries++ < INVALID_RESOLUTION_RETRIES));
+
+	if (invalid_resolution) {
+		dev_err(video->dev, "invalid resolution detected\n");
+		return -ERANGE;
+	}
+
+	video->timings.height = (bottom - top) + 1;
+	video->timings.width = (right - left) + 1;
+
+	/* Don't use direct mode below 1024 x 768 (irqs don't fire) */
+	if (video->timings.width * video->timings.height < DIRECT_FETCH_THRESHOLD) {

drivers/media/platform/aspeed-video.c line 822

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+		aspeed_video_write(video, VE_TGS_0,
+				   FIELD_PREP(VE_TGS_FIRST, left - 1) |
+				   FIELD_PREP(VE_TGS_LAST, right));
+		aspeed_video_write(video, VE_TGS_1,
+				   FIELD_PREP(VE_TGS_FIRST, top) |
+				   FIELD_PREP(VE_TGS_LAST, bottom + 1));
+		aspeed_video_update(video, VE_CTRL, 0, VE_CTRL_INT_DE);
+	} else {
+		aspeed_video_update(video, VE_CTRL, 0, VE_CTRL_DIRECT_FETCH);
+	}

Shouldn't this be done in set_capture_resolution?

drivers/media/platform/aspeed-video.c line 827

Quoted 5 lines
drivers/media/platform/aspeed-video.c new file +5 -0
+
+	aspeed_video_update(video, VE_INTERRUPT_CTRL, 0,
+			    VE_INTERRUPT_MODE_DETECT_WD);
+	aspeed_video_update(video, VE_SEQ_CTRL, 0,
+			    VE_SEQ_CTRL_AUTO_COMP | VE_SEQ_CTRL_EN_WATCHDOG);

What do these two lines do? Perhaps a comment would help.

drivers/media/platform/aspeed-video.c line 838

Quoted 11 lines
drivers/media/platform/aspeed-video.c new file +11 -0
+
+	dev_dbg(video->dev, "got resolution[%dx%d]\n", video->timings.width,
+		video->timings.height);
+
+	return 0;
+
+}
+
+static int aspeed_video_set_capture_resolution(struct aspeed_video *video)
+{
+	unsigned int size = video->timings.width * video->timings.height;

active_timings

Quoted 98 lines
drivers/media/platform/aspeed-video.c new file +98 -0
+	struct aspeed_video_addr detect = video->detect;
+
+	video->detect.size = 0;
+	video->detect.dma = 0ULL;
+	video->detect.virt = NULL;
+
+	video->capture_width = video->timings.width;
+	video->capture_height = video->timings.height;
+
+	aspeed_video_write(video, VE_CAP_WINDOW,
+			   video->capture_width << 16 | video->capture_height);
+	aspeed_video_write(video, VE_COMP_WINDOW,
+			   video->capture_width << 16 | video->capture_height);
+	aspeed_video_write(video, VE_SRC_SCANLINE_OFFSET,
+			   video->capture_width * 4);
+
+	size *= 4;
+	if (size == detect.size / 2) {
+		aspeed_video_write(video, VE_SRC1_ADDR, detect.dma + size);
+		video->srcs[0] = detect;
+	} else if (size == detect.size) {
+		video->srcs[0] = detect;
+
+		if (!aspeed_video_alloc_buf(video, &video->srcs[1], size))
+			goto err_mem;
+
+		aspeed_video_write(video, VE_SRC1_ADDR, video->srcs[1].dma);
+	} else {
+		aspeed_video_free_buf(video, &detect);
+
+		if (!aspeed_video_alloc_buf(video, &video->srcs[0], size))
+			goto err_mem;
+
+		if (!aspeed_video_alloc_buf(video, &video->srcs[1], size))
+			goto err_mem;
+
+		aspeed_video_write(video, VE_SRC0_ADDR, video->srcs[0].dma);
+		aspeed_video_write(video, VE_SRC1_ADDR, video->srcs[1].dma);
+	}
+
+	aspeed_video_calc_compressed_size(video);
+
+	dev_dbg(video->dev, "set resolution[%dx%d]\n", video->capture_width,
+		video->capture_height);
+
+	return 0;
+
+err_mem:
+	dev_err(video->dev, "failed to allocate source buffers\n");
+
+	if (video->srcs[0].size)
+		aspeed_video_free_buf(video, &video->srcs[0]);
+
+	return -ENOMEM;
+}
+
+static void aspeed_video_init_regs(struct aspeed_video *video)
+{
+	u32 comp_ctrl = VE_COMP_CTRL_RSVD |
+		FIELD_PREP(VE_COMP_CTRL_DCT_LUM, video->jpeg_quality) |
+		FIELD_PREP(VE_COMP_CTRL_DCT_CHR, video->jpeg_quality | 0x10);
+	u32 ctrl = VE_CTRL_AUTO_OR_CURSOR;
+	u32 seq_ctrl = VE_SEQ_CTRL_JPEG_MODE;
+
+	if (video->frame_rate)
+		ctrl |= FIELD_PREP(VE_CTRL_FRC, video->frame_rate);
+
+	if (video->yuv420)
+		seq_ctrl |= VE_SEQ_CTRL_YUV420;
+
+	/* Unlock VE registers */
+	aspeed_video_write(video, VE_PROTECTION_KEY, VE_PROTECTION_KEY_UNLOCK);
+
+	/* Disable interrupts */
+	aspeed_video_write(video, VE_INTERRUPT_CTRL, 0);
+	aspeed_video_write(video, VE_INTERRUPT_STATUS, 0xffffffff);
+
+	/* Clear the offset */
+	aspeed_video_write(video, VE_COMP_PROC_OFFSET, 0);
+	aspeed_video_write(video, VE_COMP_OFFSET, 0);
+
+	aspeed_video_write(video, VE_JPEG_ADDR, video->jpeg.dma);
+
+	/* Set control registers */
+	aspeed_video_write(video, VE_SEQ_CTRL, seq_ctrl);
+	aspeed_video_write(video, VE_CTRL, ctrl);
+	aspeed_video_write(video, VE_COMP_CTRL, comp_ctrl);
+
+	/* Don't downscale */
+	aspeed_video_write(video, VE_SCALING_FACTOR, 0x10001000);
+	aspeed_video_write(video, VE_SCALING_FILTER0, 0x00200000);
+	aspeed_video_write(video, VE_SCALING_FILTER1, 0x00200000);
+	aspeed_video_write(video, VE_SCALING_FILTER2, 0x00200000);
+	aspeed_video_write(video, VE_SCALING_FILTER3, 0x00200000);
+
+	/* Set mode detection defaults */
+	aspeed_video_write(video, VE_MODE_DETECT, 0x22666500);
+}

drivers/media/platform/aspeed-video.c line 946

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+
+static int aspeed_video_start(struct aspeed_video *video)
+{
+	int rc;
+
+	aspeed_video_on(video);
+
+	aspeed_video_init_regs(video);
+
+	rc = aspeed_video_get_resolution(video);

No, this shouldn't be called here. Only query_dv_timings should call this.

drivers/media/platform/aspeed-video.c line 956

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+	if (rc)
+		return rc;
+
+	rc = aspeed_video_set_capture_resolution(video);
+	if (rc)
+		return rc;
+
+	video->pix_fmt.width = video->timings.width;
+	video->pix_fmt.height = video->timings.height;
+	video->pix_fmt.sizeimage = video->max_compressed_size;

You don't set that here: otherwise opening the device node would magically change the format. That's not what should happen.

The golden rule is that you never change timings and/or format unless explicitly commanded by the application through S_DV_TIMINGS and S_FMT.

Quoted 169 lines
drivers/media/platform/aspeed-video.c new file +169 -0
+
+	return 0;
+}
+
+static void aspeed_video_stop(struct aspeed_video *video)
+{
+	cancel_delayed_work_sync(&video->res_work);
+
+	aspeed_video_off(video);
+
+	if (video->srcs[0].size)
+		aspeed_video_free_buf(video, &video->srcs[0]);
+
+	if (video->srcs[1].size)
+		aspeed_video_free_buf(video, &video->srcs[1]);
+
+	if (video->detect.size)
+		aspeed_video_free_buf(video, &video->detect);
+
+	video->flags = 0;
+}
+
+static int aspeed_video_querycap(struct file *file, void *fh,
+				 struct v4l2_capability *cap)
+{
+	strscpy(cap->driver, DEVICE_NAME, sizeof(cap->driver));
+	strscpy(cap->card, "Aspeed Video Engine", sizeof(cap->card));
+	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s",
+		 DEVICE_NAME);
+
+	return 0;
+}
+
+static int aspeed_video_enum_format(struct file *file, void *fh,
+				    struct v4l2_fmtdesc *f)
+{
+	if (f->index)
+		return -EINVAL;
+
+	f->pixelformat = V4L2_PIX_FMT_JPEG;
+
+	return 0;
+}
+
+static int aspeed_video_get_format(struct file *file, void *fh,
+				   struct v4l2_format *f)
+{
+	struct aspeed_video *video = video_drvdata(file);
+
+	f->fmt.pix = video->pix_fmt;
+
+	return 0;
+}
+
+static int aspeed_video_enum_input(struct file *file, void *fh,
+				   struct v4l2_input *inp)
+{
+	if (inp->index)
+		return -EINVAL;
+
+	strscpy(inp->name, "Host VGA capture", sizeof(inp->name));
+	inp->type = V4L2_INPUT_TYPE_CAMERA;
+	inp->capabilities = V4L2_IN_CAP_DV_TIMINGS;
+	inp->status = 0;
+
+	return 0;
+}
+
+static int aspeed_video_get_input(struct file *file, void *fh, unsigned int *i)
+{
+	*i = 0;
+
+	return 0;
+}
+
+static int aspeed_video_set_input(struct file *file, void *fh, unsigned int i)
+{
+	if (i)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int aspeed_video_get_parm(struct file *file, void *fh,
+				 struct v4l2_streamparm *a)
+{
+	struct aspeed_video *video = video_drvdata(file);
+
+	a->parm.capture.capability = V4L2_CAP_TIMEPERFRAME;
+	a->parm.capture.readbuffers = 3;
+	a->parm.capture.timeperframe.numerator = 1;
+	if (!video->frame_rate)
+		a->parm.capture.timeperframe.denominator = MAX_FRAME_RATE;
+	else
+		a->parm.capture.timeperframe.denominator = video->frame_rate;
+
+	return 0;
+}
+
+static int aspeed_video_set_parm(struct file *file, void *fh,
+				 struct v4l2_streamparm *a)
+{
+	unsigned int frame_rate = 0;
+	struct aspeed_video *video = video_drvdata(file);
+
+	a->parm.capture.capability = V4L2_CAP_TIMEPERFRAME;
+	a->parm.capture.readbuffers = 3;
+
+	if (a->parm.capture.timeperframe.numerator)
+		frame_rate = a->parm.capture.timeperframe.denominator /
+			a->parm.capture.timeperframe.numerator;
+
+	if (!frame_rate || frame_rate > MAX_FRAME_RATE) {
+		frame_rate = 0;
+		a->parm.capture.timeperframe.denominator = MAX_FRAME_RATE;
+		a->parm.capture.timeperframe.numerator = 1;
+	}
+
+	if (video->frame_rate != frame_rate) {
+		video->frame_rate = frame_rate;
+		aspeed_video_update(video, VE_CTRL, VE_CTRL_FRC,
+				    FIELD_PREP(VE_CTRL_FRC, frame_rate));
+	}
+
+	return 0;
+}
+
+static int aspeed_video_enum_framesizes(struct file *file, void *fh,
+					struct v4l2_frmsizeenum *fsize)
+{
+	struct aspeed_video *video = video_drvdata(file);
+
+	if (fsize->index)
+		return -EINVAL;
+
+	if (fsize->pixel_format != V4L2_PIX_FMT_JPEG)
+		return -EINVAL;
+
+	fsize->discrete.width = video->pix_fmt.width;
+	fsize->discrete.height = video->pix_fmt.height;
+	fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE;
+
+	return 0;
+}
+
+static int aspeed_video_enum_frameintervals(struct file *file, void *fh,
+					    struct v4l2_frmivalenum *fival)
+{
+	struct aspeed_video *video = video_drvdata(file);
+
+	if (fival->index)
+		return -EINVAL;
+
+	if (fival->width != video->timings.width ||
+	    fival->height != video->timings.height)
+		return -EINVAL;
+
+	if (fival->pixel_format != V4L2_PIX_FMT_JPEG)
+		return -EINVAL;
+
+	fival->type = V4L2_FRMIVAL_TYPE_CONTINUOUS;
+
+	fival->stepwise.min.denominator = MAX_FRAME_RATE;
+	fival->stepwise.min.numerator = 1;
+	fival->stepwise.max.denominator = 1;
+	fival->stepwise.max.numerator = 1;
+	fival->stepwise.step = fival->stepwise.max;
+
+	return 0;

drivers/media/platform/aspeed-video.c line 1135

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+}
+
+static int aspeed_video_set_dv_timings(struct file *file, void *fh,
+				       struct v4l2_dv_timings *timings)
+{
+	int rc;
+	struct aspeed_video *video = video_drvdata(file);
+
+	if (video->capture_width == timings->bt.width &&
+	    video->capture_height == timings->bt.height)

Unless I am mistaken, capture_width/height just duplicates video->pix_fmt.width/height. I'd drop capture_width/height and only use pix_fmt.

drivers/media/platform/aspeed-video.c line 1143

Quoted 8 lines
drivers/media/platform/aspeed-video.c new file +8 -0
+		return 0;
+
+	if (vb2_is_busy(&video->queue))
+		return -EBUSY;
+
+	if (video->timings.width != timings->bt.width ||
+	    video->timings.height != timings->bt.height)
+		return -EINVAL;

This 'if' makes no sense. It is perfectly fine (if silly) to set timings that do not match the current resolution. The timings can change at any time anyway, so there is no point to check this.

Quoted 11 lines
drivers/media/platform/aspeed-video.c new file +11 -0
+
+	rc = aspeed_video_set_capture_resolution(video);
+	if (rc)
+		return rc;
+
+	video->pix_fmt.width = timings->bt.width;
+	video->pix_fmt.height = timings->bt.height;
+	video->pix_fmt.sizeimage = video->max_compressed_size;
+
+	timings->type = V4L2_DV_BT_656_1120;
+

drivers/media/platform/aspeed-video.c line 1164

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+	return 0;
+}
+
+static int aspeed_video_get_dv_timings(struct file *file, void *fh,
+				       struct v4l2_dv_timings *timings)
+{
+	struct aspeed_video *video = video_drvdata(file);
+
+	timings->type = V4L2_DV_BT_656_1120;
+	timings->bt = video->timings;

Should return active_timings.

Quoted 15 lines
drivers/media/platform/aspeed-video.c new file +15 -0
+
+	return 0;
+}
+
+static int aspeed_video_query_dv_timings(struct file *file, void *fh,
+					 struct v4l2_dv_timings *timings)
+{
+	int rc;
+	struct aspeed_video *video = video_drvdata(file);
+
+	if (file->f_flags & O_NONBLOCK) {
+		if (test_bit(VIDEO_RES_CHANGE, &video->flags))
+			return -EAGAIN;
+	} else {
+		rc = wait_event_interruptible(video->wait,

drivers/media/platform/aspeed-video.c line 1189

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+					      !test_bit(VIDEO_RES_CHANGE,
+							&video->flags));
+		if (rc)
+			return -EINTR;
+	}
+
+	timings->type = V4L2_DV_BT_656_1120;
+	timings->bt = video->timings;
+	timings->bt.width = video->timings.width;
+	timings->bt.height = video->timings.height;

Should return the detected_timings.

Why assign bt.width/height again? Those two lines can be dropped.

Quoted 12 lines
drivers/media/platform/aspeed-video.c new file +12 -0
+
+	return 0;
+}
+
+static int aspeed_video_enum_dv_timings(struct file *file, void *fh,
+					struct v4l2_enum_dv_timings *timings)
+{
+	if (timings->index)
+		return -EINVAL;
+
+	return aspeed_video_get_dv_timings(file, fh, &timings->timings);
+}

drivers/media/platform/aspeed-video.c line 1211

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+
+static int aspeed_video_dv_timings_cap(struct file *file, void *fh,
+				       struct v4l2_dv_timings_cap *cap)
+{
+	cap->type = V4L2_DV_BT_656_1120;
+	cap->bt.capabilities = V4L2_DV_BT_CAP_PROGRESSIVE;
+	cap->bt.min_width = MIN_WIDTH;
+	cap->bt.max_width = MAX_WIDTH;
+	cap->bt.min_height = MIN_HEIGHT;
+	cap->bt.max_height = MAX_HEIGHT;

I would create a static const struct v4l2_dv_timings_cap at the top of the source and return that here.

You can then use the helpers v4l2_valid_dv_timings in s_dv_timings and v4l2_enum_dv_timings_cap in enum_dv_timings.

You need to set the V4L2_DV_BT_CAP_REDUCED_BLANKING capability as well. And fill in cap->bt.min/max_pixelclock and standards (CEA861|DMT|CVT|GTF).

Quoted 136 lines
drivers/media/platform/aspeed-video.c new file +136 -0
+
+	return 0;
+}
+
+static int aspeed_video_sub_event(struct v4l2_fh *fh,
+				  const struct v4l2_event_subscription *sub)
+{
+	switch (sub->type) {
+	case V4L2_EVENT_SOURCE_CHANGE:
+		return v4l2_src_change_event_subscribe(fh, sub);
+	}
+
+	return v4l2_ctrl_subscribe_event(fh, sub);
+}
+
+static const struct v4l2_ioctl_ops aspeed_video_ioctl_ops = {
+	.vidioc_querycap = aspeed_video_querycap,
+
+	.vidioc_enum_fmt_vid_cap = aspeed_video_enum_format,
+	.vidioc_g_fmt_vid_cap = aspeed_video_get_format,
+	.vidioc_s_fmt_vid_cap = aspeed_video_get_format,
+	.vidioc_try_fmt_vid_cap = aspeed_video_get_format,
+
+	.vidioc_reqbufs = vb2_ioctl_reqbufs,
+	.vidioc_querybuf = vb2_ioctl_querybuf,
+	.vidioc_qbuf = vb2_ioctl_qbuf,
+	.vidioc_dqbuf = vb2_ioctl_dqbuf,
+	.vidioc_create_bufs = vb2_ioctl_create_bufs,
+	.vidioc_prepare_buf = vb2_ioctl_prepare_buf,
+	.vidioc_streamon = vb2_ioctl_streamon,
+	.vidioc_streamoff = vb2_ioctl_streamoff,
+
+	.vidioc_enum_input = aspeed_video_enum_input,
+	.vidioc_g_input = aspeed_video_get_input,
+	.vidioc_s_input = aspeed_video_set_input,
+
+	.vidioc_g_parm = aspeed_video_get_parm,
+	.vidioc_s_parm = aspeed_video_set_parm,
+	.vidioc_enum_framesizes = aspeed_video_enum_framesizes,
+	.vidioc_enum_frameintervals = aspeed_video_enum_frameintervals,
+
+	.vidioc_s_dv_timings = aspeed_video_set_dv_timings,
+	.vidioc_g_dv_timings = aspeed_video_get_dv_timings,
+	.vidioc_query_dv_timings = aspeed_video_query_dv_timings,
+	.vidioc_enum_dv_timings = aspeed_video_enum_dv_timings,
+	.vidioc_dv_timings_cap = aspeed_video_dv_timings_cap,
+
+	.vidioc_subscribe_event = aspeed_video_sub_event,
+	.vidioc_unsubscribe_event = v4l2_event_unsubscribe,
+};
+
+static void aspeed_video_update_jpeg_quality(struct aspeed_video *video)
+{
+	u32 comp_ctrl = FIELD_PREP(VE_COMP_CTRL_DCT_LUM, video->jpeg_quality) |
+		FIELD_PREP(VE_COMP_CTRL_DCT_CHR, video->jpeg_quality | 0x10);
+
+	aspeed_video_update(video, VE_COMP_CTRL,
+			    VE_COMP_CTRL_DCT_LUM | VE_COMP_CTRL_DCT_CHR,
+			    comp_ctrl);
+}
+
+static void aspeed_video_update_subsampling(struct aspeed_video *video)
+{
+	if (video->jpeg.virt)
+		aspeed_video_init_jpeg_table(video->jpeg.virt, video->yuv420);
+
+	if (video->yuv420)
+		aspeed_video_update(video, VE_SEQ_CTRL, 0, VE_SEQ_CTRL_YUV420);
+	else
+		aspeed_video_update(video, VE_SEQ_CTRL, VE_SEQ_CTRL_YUV420, 0);
+}
+
+static int aspeed_video_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct aspeed_video *video = container_of(ctrl->handler,
+						  struct aspeed_video,
+						  ctrl_handler);
+
+	switch (ctrl->id) {
+	case V4L2_CID_JPEG_COMPRESSION_QUALITY:
+		video->jpeg_quality = ctrl->val;
+		aspeed_video_update_jpeg_quality(video);
+		break;
+	case V4L2_CID_JPEG_CHROMA_SUBSAMPLING:
+		if (ctrl->val == V4L2_JPEG_CHROMA_SUBSAMPLING_420) {
+			video->yuv420 = true;
+			aspeed_video_update_subsampling(video);
+		} else {
+			video->yuv420 = false;
+			aspeed_video_update_subsampling(video);
+		}
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static const struct v4l2_ctrl_ops aspeed_video_ctrl_ops = {
+	.s_ctrl = aspeed_video_set_ctrl,
+};
+
+static void aspeed_video_resolution_work(struct work_struct *work)
+{
+	int rc;
+	struct delayed_work *dwork = to_delayed_work(work);
+	struct aspeed_video *video = container_of(dwork, struct aspeed_video,
+						  res_work);
+
+	/* No clients remaining after delay */
+	if (atomic_read(&video->clients) == 0)
+		goto done;
+
+	aspeed_video_on(video);
+
+	aspeed_video_init_regs(video);
+
+	rc = aspeed_video_get_resolution(video);
+	if (rc)
+		dev_err(video->dev,
+			"resolution changed; couldn't get new resolution\n");
+
+	if (video->timings.width != video->pix_fmt.width ||
+	    video->timings.height != video->pix_fmt.height) {
+		static const struct v4l2_event ev = {
+			.type = V4L2_EVENT_SOURCE_CHANGE,
+			.u.src_change.changes = V4L2_EVENT_SRC_CH_RESOLUTION,
+		};
+
+		v4l2_event_queue(&video->vdev, &ev);
+	}
+
+done:
+	clear_bit(VIDEO_RES_CHANGE, &video->flags);
+	wake_up_interruptible_all(&video->wait);

drivers/media/platform/aspeed-video.c line 1357

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+}
+
+static int aspeed_video_open(struct file *file)
+{
+	int rc;
+	struct aspeed_video *video = video_drvdata(file);
+
+	mutex_lock(&video->video_lock);
+
+	if (atomic_inc_return(&video->clients) == 1) {

No need for a clients refcount. You can use the v4l2_fh_is_singular(_file) helpers. See how other drivers do this.

Quoted 345 lines
drivers/media/platform/aspeed-video.c new file +344 -0
+		rc = aspeed_video_start(video);
+		if (rc) {
+			dev_err(video->dev, "Failed to start video engine\n");
+			atomic_dec(&video->clients);
+			mutex_unlock(&video->video_lock);
+			return rc;
+		}
+	}
+
+	mutex_unlock(&video->video_lock);
+
+	return v4l2_fh_open(file);
+}
+
+static int aspeed_video_release(struct file *file)
+{
+	int rc;
+	struct aspeed_video *video = video_drvdata(file);
+
+	rc = vb2_fop_release(file);
+
+	mutex_lock(&video->video_lock);
+
+	if (atomic_dec_return(&video->clients) == 0)
+		aspeed_video_stop(video);
+
+	mutex_unlock(&video->video_lock);
+
+	return rc;
+}
+
+static const struct v4l2_file_operations aspeed_video_v4l2_fops = {
+	.owner = THIS_MODULE,
+	.read = vb2_fop_read,
+	.poll = vb2_fop_poll,
+	.unlocked_ioctl = video_ioctl2,
+	.mmap = vb2_fop_mmap,
+	.open = aspeed_video_open,
+	.release = aspeed_video_release,
+};
+
+static int aspeed_video_queue_setup(struct vb2_queue *q,
+				    unsigned int *num_buffers,
+				    unsigned int *num_planes,
+				    unsigned int sizes[],
+				    struct device *alloc_devs[])
+{
+	struct aspeed_video *video = vb2_get_drv_priv(q);
+
+	if (*num_planes) {
+		if (sizes[0] < video->max_compressed_size)
+			return -EINVAL;
+
+		return 0;
+	}
+
+	*num_planes = 1;
+	sizes[0] = video->max_compressed_size;
+
+	return 0;
+}
+
+static int aspeed_video_buf_prepare(struct vb2_buffer *vb)
+{
+	struct aspeed_video *video = vb2_get_drv_priv(vb->vb2_queue);
+
+	if (vb2_plane_size(vb, 0) < video->max_compressed_size)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int aspeed_video_start_streaming(struct vb2_queue *q,
+					unsigned int count)
+{
+	int rc;
+	struct aspeed_video *video = vb2_get_drv_priv(q);
+
+	rc = aspeed_video_start_frame(video);
+	if (rc) {
+		aspeed_video_bufs_done(video, VB2_BUF_STATE_QUEUED);
+		return rc;
+	}
+
+	video->sequence = 0;
+	set_bit(VIDEO_STREAMING, &video->flags);
+	return 0;
+}
+
+static void aspeed_video_stop_streaming(struct vb2_queue *q)
+{
+	int rc;
+	struct aspeed_video *video = vb2_get_drv_priv(q);
+
+	clear_bit(VIDEO_STREAMING, &video->flags);
+
+	rc = wait_event_timeout(video->wait,
+				!test_bit(VIDEO_FRAME_INPRG, &video->flags),
+				STOP_TIMEOUT);
+	if (!rc) {
+		dev_err(video->dev, "Timed out when stopping streaming\n");
+		aspeed_video_stop(video);
+	}
+
+	aspeed_video_bufs_done(video, VB2_BUF_STATE_ERROR);
+}
+
+static void aspeed_video_buf_queue(struct vb2_buffer *vb)
+{
+	struct aspeed_video *video = vb2_get_drv_priv(vb->vb2_queue);
+	struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb);
+	struct aspeed_video_buffer *avb = to_aspeed_video_buffer(vbuf);
+	unsigned long flags;
+
+	spin_lock_irqsave(&video->lock, flags);
+	list_add_tail(&avb->link, &video->buffers);
+	spin_unlock_irqrestore(&video->lock, flags);
+}
+
+static const struct vb2_ops aspeed_video_vb2_ops = {
+	.queue_setup = aspeed_video_queue_setup,
+	.wait_prepare = vb2_ops_wait_prepare,
+	.wait_finish = vb2_ops_wait_finish,
+	.buf_prepare = aspeed_video_buf_prepare,
+	.start_streaming = aspeed_video_start_streaming,
+	.stop_streaming = aspeed_video_stop_streaming,
+	.buf_queue =  aspeed_video_buf_queue,
+};
+
+static int aspeed_video_setup_video(struct aspeed_video *video)
+{
+	const u64 mask = ~(BIT(V4L2_JPEG_CHROMA_SUBSAMPLING_444) |
+			   BIT(V4L2_JPEG_CHROMA_SUBSAMPLING_420));
+	struct v4l2_device *v4l2_dev = &video->v4l2_dev;
+	struct vb2_queue *vbq = &video->queue;
+	struct video_device *vdev = &video->vdev;
+	int rc;
+
+	video->pix_fmt.pixelformat = V4L2_PIX_FMT_JPEG;
+	video->pix_fmt.field = V4L2_FIELD_NONE;
+	video->pix_fmt.colorspace = V4L2_COLORSPACE_SRGB;
+	video->pix_fmt.quantization = V4L2_QUANTIZATION_FULL_RANGE;
+
+	rc = v4l2_device_register(video->dev, v4l2_dev);
+	if (rc) {
+		dev_err(video->dev, "Failed to register v4l2 device\n");
+		return rc;
+	}
+
+	v4l2_ctrl_handler_init(&video->ctrl_handler, 2);
+	v4l2_ctrl_new_std(&video->ctrl_handler, &aspeed_video_ctrl_ops,
+			  V4L2_CID_JPEG_COMPRESSION_QUALITY, 0,
+			  ASPEED_VIDEO_JPEG_NUM_QUALITIES - 1, 1, 0);
+	v4l2_ctrl_new_std_menu(&video->ctrl_handler, &aspeed_video_ctrl_ops,
+			       V4L2_CID_JPEG_CHROMA_SUBSAMPLING,
+			       V4L2_JPEG_CHROMA_SUBSAMPLING_420, mask,
+			       V4L2_JPEG_CHROMA_SUBSAMPLING_444);
+
+	if (video->ctrl_handler.error) {
+		v4l2_ctrl_handler_free(&video->ctrl_handler);
+		v4l2_device_unregister(v4l2_dev);
+
+		dev_err(video->dev, "Failed to init controls: %d\n",
+			video->ctrl_handler.error);
+		return rc;
+	}
+
+	v4l2_dev->ctrl_handler = &video->ctrl_handler;
+
+	vbq->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
+	vbq->io_modes = VB2_MMAP | VB2_READ | VB2_DMABUF;
+	vbq->dev = v4l2_dev->dev;
+	vbq->lock = &video->video_lock;
+	vbq->ops = &aspeed_video_vb2_ops;
+	vbq->mem_ops = &vb2_dma_contig_memops;
+	vbq->drv_priv = video;
+	vbq->buf_struct_size = sizeof(struct aspeed_video_buffer);
+	vbq->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC;
+	vbq->min_buffers_needed = 3;
+
+	rc = vb2_queue_init(vbq);
+	if (rc) {
+		v4l2_ctrl_handler_free(&video->ctrl_handler);
+		v4l2_device_unregister(v4l2_dev);
+
+		dev_err(video->dev, "Failed to init vb2 queue\n");
+		return rc;
+	}
+
+	vdev->queue = vbq;
+	vdev->fops = &aspeed_video_v4l2_fops;
+	vdev->device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_READWRITE |
+		V4L2_CAP_STREAMING;
+	vdev->v4l2_dev = v4l2_dev;
+	strscpy(vdev->name, DEVICE_NAME, sizeof(vdev->name));
+	vdev->vfl_type = VFL_TYPE_GRABBER;
+	vdev->vfl_dir = VFL_DIR_RX;
+	vdev->release = video_device_release_empty;
+	vdev->ioctl_ops = &aspeed_video_ioctl_ops;
+	vdev->lock = &video->video_lock;
+
+	video_set_drvdata(vdev, video);
+	rc = video_register_device(vdev, VFL_TYPE_GRABBER, 0);
+	if (rc) {
+		vb2_queue_release(vbq);
+		v4l2_ctrl_handler_free(&video->ctrl_handler);
+		v4l2_device_unregister(v4l2_dev);
+
+		dev_err(video->dev, "Failed to register video device\n");
+		return rc;
+	}
+
+	return 0;
+}
+
+static int aspeed_video_init(struct aspeed_video *video)
+{
+	int irq;
+	int rc;
+	struct device *dev = video->dev;
+
+	irq = irq_of_parse_and_map(dev->of_node, 0);
+	if (!irq) {
+		dev_err(dev, "Unable to find IRQ\n");
+		return -ENODEV;
+	}
+
+	rc = devm_request_irq(dev, irq, aspeed_video_irq, IRQF_SHARED,
+			      DEVICE_NAME, video);
+	if (rc < 0) {
+		dev_err(dev, "Unable to request IRQ %d\n", irq);
+		return rc;
+	}
+
+	video->eclk = devm_clk_get(dev, "eclk");
+	if (IS_ERR(video->eclk)) {
+		dev_err(dev, "Unable to get ECLK\n");
+		return PTR_ERR(video->eclk);
+	}
+
+	video->vclk = devm_clk_get(dev, "vclk");
+	if (IS_ERR(video->vclk)) {
+		dev_err(dev, "Unable to get VCLK\n");
+		return PTR_ERR(video->vclk);
+	}
+
+	video->rst = devm_reset_control_get_exclusive(dev, NULL);
+	if (IS_ERR(video->rst)) {
+		dev_err(dev, "Unable to get VE reset\n");
+		return PTR_ERR(video->rst);
+	}
+
+	rc = of_reserved_mem_device_init(dev);
+	if (rc) {
+		dev_err(dev, "Unable to reserve memory\n");
+		return rc;
+	}
+
+	rc = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
+	if (rc) {
+		dev_err(dev, "Failed to set DMA mask\n");
+		of_reserved_mem_device_release(dev);
+		return rc;
+	}
+
+	if (!aspeed_video_alloc_buf(video, &video->jpeg,
+				    VE_JPEG_HEADER_SIZE)) {
+		dev_err(dev, "Failed to allocate DMA for JPEG header\n");
+		of_reserved_mem_device_release(dev);
+		return rc;
+	}
+
+	aspeed_video_init_jpeg_table(video->jpeg.virt, video->yuv420);
+
+	return 0;
+}
+
+static int aspeed_video_probe(struct platform_device *pdev)
+{
+	int rc;
+	struct resource *res;
+	struct aspeed_video *video = kzalloc(sizeof(*video), GFP_KERNEL);
+
+	if (!video)
+		return -ENOMEM;
+
+	video->frame_rate = 30;
+	video->dev = &pdev->dev;
+	mutex_init(&video->video_lock);
+	init_waitqueue_head(&video->wait);
+	INIT_DELAYED_WORK(&video->res_work, aspeed_video_resolution_work);
+	INIT_LIST_HEAD(&video->buffers);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+	video->base = devm_ioremap_resource(video->dev, res);
+
+	if (IS_ERR(video->base))
+		return PTR_ERR(video->base);
+
+	rc = aspeed_video_init(video);
+	if (rc)
+		return rc;
+
+	rc = aspeed_video_setup_video(video);
+	if (rc)
+		return rc;
+
+	return 0;
+}
+
+static int aspeed_video_remove(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct v4l2_device *v4l2_dev = dev_get_drvdata(dev);
+	struct aspeed_video *video = to_aspeed_video(v4l2_dev);
+
+	video_unregister_device(&video->vdev);
+
+	vb2_queue_release(&video->queue);
+
+	v4l2_ctrl_handler_free(&video->ctrl_handler);
+
+	v4l2_device_unregister(v4l2_dev);
+
+	dma_free_coherent(video->dev, VE_JPEG_HEADER_SIZE, video->jpeg.virt,
+			  video->jpeg.dma);
+
+	of_reserved_mem_device_release(dev);
+
+	return 0;
+}
+
+static const struct of_device_id aspeed_video_of_match[] = {
+	{ .compatible = "aspeed,ast2400-video-engine" },
+	{ .compatible = "aspeed,ast2500-video-engine" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, aspeed_video_of_match);
+
+static struct platform_driver aspeed_video_driver = {
+	.driver = {
+		.name = DEVICE_NAME,
+		.of_match_table = aspeed_video_of_match,

drivers/media/platform/aspeed-video.c line 1711

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+	},
+	.probe = aspeed_video_probe,
+	.remove = aspeed_video_remove,
+};
+
+module_platform_driver(aspeed_video_driver);
+
+MODULE_DESCRIPTION("ASPEED Video Engine Driver");
+MODULE_AUTHOR("Eddie James");
+MODULE_LICENSE("GPL v2");

Regards,

Hans

#4 lore raw

Re: [PATCH v5 2/2] media: platform: Add Aspeed Video Engine driver

Quoted 592 lines · Hans Verkuil
Quoted 278 lines · Eddie James

The Video Engine (VE) embedded in the Aspeed AST2400 and AST2500 SOCs can capture and compress video data from digital or analog sources. With the Aspeed chip acting a service processor, the Video Engine can capture the host processor graphics output.

Add a V4L2 driver to capture video data and compress it to JPEG images. Make the video frames available through the V4L2 streaming interface.

---
  MAINTAINERS                           |    8 +
  drivers/media/platform/Kconfig        |    9 +
  drivers/media/platform/Makefile       |    1 +
  drivers/media/platform/aspeed-video.c | 1711 +++++++++++++++++++++++++++++++++
  4 files changed, 1729 insertions(+)

create mode 100644 drivers/media/platform/aspeed-video.c

MAINTAINERS +8 -0
index fa45ff3..f8f08a4 100644
@@ -2414,6 +2414,14 @@ S:	Maintained
  F:	Documentation/hwmon/asc7621
  F:	drivers/hwmon/asc7621.c
 
+ASPEED VIDEO ENGINE DRIVER
+M:	Eddie James <[email protected]>
+L:	linux-media at vger.kernel.org
+L:	openbmc at lists.ozlabs.org (moderated for non-subscribers)
+S:	Maintained
+F:	drivers/media/platform/aspeed-video.c
+F:	Documentation/devicetree/bindings/media/aspeed-video.txt
+
  ASUS NOTEBOOKS AND EEEPC ACPI/WMI EXTRAS DRIVERS
  M:	Corentin Chary <[email protected]>
  L:	acpi4asus-user at lists.sourceforge.net
drivers/media/platform/Kconfig +9 -0
index 70c4f6c..ba78dd5 100644
@@ -32,6 +32,15 @@ source "drivers/media/platform/davinci/Kconfig"
 
  source "drivers/media/platform/omap/Kconfig"
 
+config VIDEO_ASPEED
+	tristate "Aspeed AST2400 and AST2500 Video Engine driver"
+	depends on VIDEO_V4L2
+	select VIDEOBUF2_DMA_CONTIG
+	help
+	  Support for the Aspeed Video Engine (VE) embedded in the Aspeed
+	  AST2400 and AST2500 SOCs. The VE can capture and compress video data
+	  from digital or analog sources.
+
  config VIDEO_SH_VOU
  	tristate "SuperH VOU video output driver"
  	depends on MEDIA_CAMERA_SUPPORT
drivers/media/platform/Makefile +1 -0
index 6ab6200..2973953 100644
@@ -3,6 +3,7 @@
  # Makefile for the video capture/playback device drivers.
  #
 
+obj-$(CONFIG_VIDEO_ASPEED)		+= aspeed-video.o
  obj-$(CONFIG_VIDEO_CADENCE)		+= cadence/
  obj-$(CONFIG_VIDEO_VIA_CAMERA) += via-camera.o
  obj-$(CONFIG_VIDEO_CAFE_CCIC) += marvell-ccic/
drivers/media/platform/aspeed-video.c new file +204 -0
new file mode 100644
index 0000000..a2fd0bf
@@ -0,0 +1,1711 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <linux/atomic.h>
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/interrupt.h>
+#include <linux/jiffies.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+#include <linux/sched.h>
+#include <linux/spinlock.h>
+#include <linux/string.h>
+#include <linux/v4l2-controls.h>
+#include <linux/videodev2.h>
+#include <linux/wait.h>
+#include <linux/workqueue.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-dev.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-ioctl.h>
+#include <media/videobuf2-dma-contig.h>
+
+#define DEVICE_NAME			"aspeed-video"
+
+#define ASPEED_VIDEO_JPEG_NUM_QUALITIES	12
+#define ASPEED_VIDEO_JPEG_HEADER_SIZE	10
+#define ASPEED_VIDEO_JPEG_QUANT_SIZE	116
+#define ASPEED_VIDEO_JPEG_DCT_SIZE	34
+
+#define MAX_FRAME_RATE			60
+#define MAX_HEIGHT			1200
+#define MAX_WIDTH			1920
+#define MIN_HEIGHT			480
+#define MIN_WIDTH			640
+
+#define NUM_POLARITY_CHECKS		10
+#define INVALID_RESOLUTION_RETRIES	2
+#define INVALID_RESOLUTION_DELAY	msecs_to_jiffies(250)
+#define RESOLUTION_CHANGE_DELAY		msecs_to_jiffies(500)
+#define MODE_DETECT_TIMEOUT		msecs_to_jiffies(500)
+#define STOP_TIMEOUT			msecs_to_jiffies(250)
+#define DIRECT_FETCH_THRESHOLD		0x0c0000 /* 1024 * 768 */
+
+#define VE_MAX_SRC_BUFFER_SIZE		0x8ca000 /* 1920 * 1200, 32bpp */
+#define VE_JPEG_HEADER_SIZE		0x006000 /* 512 * 12 * 4 */
+
+#define VE_PROTECTION_KEY		0x000
+#define  VE_PROTECTION_KEY_UNLOCK	0x1a038aa8
+
+#define VE_SEQ_CTRL			0x004
+#define  VE_SEQ_CTRL_TRIG_MODE_DET	BIT(0)
+#define  VE_SEQ_CTRL_TRIG_CAPTURE	BIT(1)
+#define  VE_SEQ_CTRL_FORCE_IDLE		BIT(2)
+#define  VE_SEQ_CTRL_MULT_FRAME		BIT(3)
+#define  VE_SEQ_CTRL_TRIG_COMP		BIT(4)
+#define  VE_SEQ_CTRL_AUTO_COMP		BIT(5)
+#define  VE_SEQ_CTRL_EN_WATCHDOG	BIT(7)
+#define  VE_SEQ_CTRL_YUV420		BIT(10)
+#define  VE_SEQ_CTRL_COMP_FMT		GENMASK(11, 10)
+#define  VE_SEQ_CTRL_HALT		BIT(12)
+#define  VE_SEQ_CTRL_EN_WATCHDOG_COMP	BIT(14)
+#define  VE_SEQ_CTRL_TRIG_JPG		BIT(15)
+#define  VE_SEQ_CTRL_CAP_BUSY		BIT(16)
+#define  VE_SEQ_CTRL_COMP_BUSY		BIT(18)
+
+#ifdef CONFIG_MACH_ASPEED_G5
+#define  VE_SEQ_CTRL_JPEG_MODE		BIT(13)	/* AST2500 */
+#else
+#define  VE_SEQ_CTRL_JPEG_MODE		BIT(8)	/* AST2400 */
+#endif /* CONFIG_MACH_ASPEED_G5 */
+
+#define VE_CTRL				0x008
+#define  VE_CTRL_HSYNC_POL		BIT(0)
+#define  VE_CTRL_VSYNC_POL		BIT(1)
+#define  VE_CTRL_SOURCE			BIT(2)
+#define  VE_CTRL_INT_DE			BIT(4)
+#define  VE_CTRL_DIRECT_FETCH		BIT(5)
+#define  VE_CTRL_YUV			BIT(6)
+#define  VE_CTRL_RGB			BIT(7)
+#define  VE_CTRL_CAPTURE_FMT		GENMASK(7, 6)
+#define  VE_CTRL_AUTO_OR_CURSOR		BIT(8)
+#define  VE_CTRL_CLK_INVERSE		BIT(11)
+#define  VE_CTRL_CLK_DELAY		GENMASK(11, 9)
+#define  VE_CTRL_INTERLACE		BIT(14)
+#define  VE_CTRL_HSYNC_POL_CTRL		BIT(15)
+#define  VE_CTRL_FRC			GENMASK(23, 16)
+
+#define VE_TGS_0			0x00c
+#define VE_TGS_1			0x010
+#define  VE_TGS_FIRST			GENMASK(28, 16)
+#define  VE_TGS_LAST			GENMASK(12, 0)
+
+#define VE_SCALING_FACTOR		0x014
+#define VE_SCALING_FILTER0		0x018
+#define VE_SCALING_FILTER1		0x01c
+#define VE_SCALING_FILTER2		0x020
+#define VE_SCALING_FILTER3		0x024
+
+#define VE_CAP_WINDOW			0x030
+#define VE_COMP_WINDOW			0x034
+#define VE_COMP_PROC_OFFSET		0x038
+#define VE_COMP_OFFSET			0x03c
+#define VE_JPEG_ADDR			0x040
+#define VE_SRC0_ADDR			0x044
+#define VE_SRC_SCANLINE_OFFSET		0x048
+#define VE_SRC1_ADDR			0x04c
+#define VE_COMP_ADDR			0x054
+
+#define VE_STREAM_BUF_SIZE		0x058
+#define  VE_STREAM_BUF_SIZE_N_PACKETS	GENMASK(5, 3)
+#define  VE_STREAM_BUF_SIZE_P_SIZE	GENMASK(2, 0)
+
+#define VE_COMP_CTRL			0x060
+#define  VE_COMP_CTRL_VQ_DCT_ONLY	BIT(0)
+#define  VE_COMP_CTRL_VQ_4COLOR		BIT(1)
+#define  VE_COMP_CTRL_QUANTIZE		BIT(2)
+#define  VE_COMP_CTRL_EN_BQ		BIT(4)
+#define  VE_COMP_CTRL_EN_CRYPTO		BIT(5)
+#define  VE_COMP_CTRL_DCT_CHR		GENMASK(10, 6)
+#define  VE_COMP_CTRL_DCT_LUM		GENMASK(15, 11)
+#define  VE_COMP_CTRL_EN_HQ		BIT(16)
+#define  VE_COMP_CTRL_RSVD		BIT(19)
+#define  VE_COMP_CTRL_ENCODE		GENMASK(21, 20)
+#define  VE_COMP_CTRL_HQ_DCT_CHR	GENMASK(26, 22)
+#define  VE_COMP_CTRL_HQ_DCT_LUM	GENMASK(31, 27)
+
+#define VE_OFFSET_COMP_STREAM		0x078
+
+#define VE_SRC_LR_EDGE_DET		0x090
+#define  VE_SRC_LR_EDGE_DET_LEFT	GENMASK(11, 0)
+#define  VE_SRC_LR_EDGE_DET_NO_V	BIT(12)
+#define  VE_SRC_LR_EDGE_DET_NO_H	BIT(13)
+#define  VE_SRC_LR_EDGE_DET_NO_DISP	BIT(14)
+#define  VE_SRC_LR_EDGE_DET_NO_CLK	BIT(15)
+#define  VE_SRC_LR_EDGE_DET_RT_SHF	16
+#define  VE_SRC_LR_EDGE_DET_RT		GENMASK(27, VE_SRC_LR_EDGE_DET_RT_SHF)
+#define  VE_SRC_LR_EDGE_DET_INTERLACE	BIT(31)
+
+#define VE_SRC_TB_EDGE_DET		0x094
+#define  VE_SRC_TB_EDGE_DET_TOP		GENMASK(12, 0)
+#define  VE_SRC_TB_EDGE_DET_BOT_SHF	16
+#define  VE_SRC_TB_EDGE_DET_BOT		GENMASK(28, VE_SRC_TB_EDGE_DET_BOT_SHF)
+
+#define VE_MODE_DETECT_STATUS		0x098
+#define  VE_MODE_DETECT_H_PIXELS	GENMASK(11, 0)
+#define  VE_MODE_DETECT_V_LINES_SHF	16
+#define  VE_MODE_DETECT_V_LINES		GENMASK(27, VE_MODE_DETECT_V_LINES_SHF)
+#define  VE_MODE_DETECT_STATUS_VSYNC	BIT(28)
+#define  VE_MODE_DETECT_STATUS_HSYNC	BIT(29)
+
+#define VE_SYNC_STATUS			0x09c
+#define  VE_SYNC_STATUS_HSYNC		GENMASK(11, 0)
+#define  VE_SYNC_STATUS_VSYNC_SHF	16
+#define  VE_SYNC_STATUS_VSYNC		GENMASK(27, VE_SYNC_STATUS_VSYNC_SHF)
+
+#define VE_INTERRUPT_CTRL		0x304
+#define VE_INTERRUPT_STATUS		0x308
+#define  VE_INTERRUPT_MODE_DETECT_WD	BIT(0)
+#define  VE_INTERRUPT_CAPTURE_COMPLETE	BIT(1)
+#define  VE_INTERRUPT_COMP_READY	BIT(2)
+#define  VE_INTERRUPT_COMP_COMPLETE	BIT(3)
+#define  VE_INTERRUPT_MODE_DETECT	BIT(4)
+#define  VE_INTERRUPT_FRAME_COMPLETE	BIT(5)
+#define  VE_INTERRUPT_DECODE_ERR	BIT(6)
+#define  VE_INTERRUPT_HALT_READY	BIT(8)
+#define  VE_INTERRUPT_HANG_WD		BIT(9)
+#define  VE_INTERRUPT_STREAM_DESC	BIT(10)
+#define  VE_INTERRUPT_VSYNC_DESC	BIT(11)
+
+#define VE_MODE_DETECT			0x30c
+#define VE_MEM_RESTRICT_START		0x310
+#define VE_MEM_RESTRICT_END		0x314
+
+enum {
+	VIDEO_MODE_DETECT_DONE,
+	VIDEO_RES_CHANGE,
+	VIDEO_STREAMING,
+	VIDEO_FRAME_INPRG,
+};
+
+struct aspeed_video_addr {
+	unsigned int size;
+	dma_addr_t dma;
+	void *virt;
+};
+
+struct aspeed_video_buffer {
+	struct vb2_v4l2_buffer vb;
+	struct list_head link;
+};
+
+#define to_aspeed_video_buffer(x) \
+	container_of((x), struct aspeed_video_buffer, vb)
+
+struct aspeed_video {

drivers/media/platform/aspeed-video.c line 214

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+	void __iomem *base;
+	struct clk *eclk;
+	struct clk *vclk;
+	struct reset_control *rst;
+
+	struct device *dev;
+	struct v4l2_ctrl_handler ctrl_handler;
+	struct v4l2_device v4l2_dev;
+	struct v4l2_pix_format pix_fmt;
+	struct v4l2_bt_timings timings;

You need two v4l2_bt_timings structs here:

	struct v4l2_bt_timings active_timings;
	struct v4l2_bt_timings detected_timings;

The first is what s_dv_timings set (and must also be initialized to some timing at probe time), the second is what aspeed_video_get_resolution fills in.

See more about this below.

Quoted 242 lines
drivers/media/platform/aspeed-video.c new file +242 -0
+	struct vb2_queue queue;
+	struct video_device vdev;
+	struct mutex video_lock;
+
+	atomic_t clients;
+	wait_queue_head_t wait;
+	spinlock_t lock;
+	struct delayed_work res_work;
+	struct list_head buffers;
+	unsigned long flags;
+	unsigned int sequence;
+
+	unsigned int max_compressed_size;
+	struct aspeed_video_addr srcs[2];
+	struct aspeed_video_addr jpeg;
+	struct aspeed_video_addr detect;
+
+	bool yuv420;
+	unsigned int frame_rate;
+	unsigned int jpeg_quality;
+	unsigned int capture_height;
+	unsigned int capture_width;
+};
+
+#define to_aspeed_video(x) container_of((x), struct aspeed_video, v4l2_dev)
+
+static const u32 aspeed_video_jpeg_header[ASPEED_VIDEO_JPEG_HEADER_SIZE] = {
+	0xe0ffd8ff, 0x464a1000, 0x01004649, 0x60000101, 0x00006000, 0x0f00feff,
+	0x00002d05, 0x00000000, 0x00000000, 0x00dbff00
+};
+
+static const u32 aspeed_video_jpeg_quant[ASPEED_VIDEO_JPEG_QUANT_SIZE] = {
+	0x081100c0, 0x00000000, 0x00110103, 0x03011102, 0xc4ff0111, 0x00001f00,
+	0x01010501, 0x01010101, 0x00000000, 0x00000000, 0x04030201, 0x08070605,
+	0xff0b0a09, 0x10b500c4, 0x03010200, 0x03040203, 0x04040505, 0x7d010000,
+	0x00030201, 0x12051104, 0x06413121, 0x07615113, 0x32147122, 0x08a19181,
+	0xc1b14223, 0xf0d15215, 0x72623324, 0x160a0982, 0x1a191817, 0x28272625,
+	0x35342a29, 0x39383736, 0x4544433a, 0x49484746, 0x5554534a, 0x59585756,
+	0x6564635a, 0x69686766, 0x7574736a, 0x79787776, 0x8584837a, 0x89888786,
+	0x9493928a, 0x98979695, 0xa3a29a99, 0xa7a6a5a4, 0xb2aaa9a8, 0xb6b5b4b3,
+	0xbab9b8b7, 0xc5c4c3c2, 0xc9c8c7c6, 0xd4d3d2ca, 0xd8d7d6d5, 0xe2e1dad9,
+	0xe6e5e4e3, 0xeae9e8e7, 0xf4f3f2f1, 0xf8f7f6f5, 0xc4fffaf9, 0x00011f00,
+	0x01010103, 0x01010101, 0x00000101, 0x00000000, 0x04030201, 0x08070605,
+	0xff0b0a09, 0x11b500c4, 0x02010200, 0x04030404, 0x04040507, 0x77020100,
+	0x03020100, 0x21050411, 0x41120631, 0x71610751, 0x81322213, 0x91421408,
+	0x09c1b1a1, 0xf0523323, 0xd1726215, 0x3424160a, 0x17f125e1, 0x261a1918,
+	0x2a292827, 0x38373635, 0x44433a39, 0x48474645, 0x54534a49, 0x58575655,
+	0x64635a59, 0x68676665, 0x74736a69, 0x78777675, 0x83827a79, 0x87868584,
+	0x928a8988, 0x96959493, 0x9a999897, 0xa5a4a3a2, 0xa9a8a7a6, 0xb4b3b2aa,
+	0xb8b7b6b5, 0xc3c2bab9, 0xc7c6c5c4, 0xd2cac9c8, 0xd6d5d4d3, 0xdad9d8d7,
+	0xe5e4e3e2, 0xe9e8e7e6, 0xf4f3f2ea, 0xf8f7f6f5, 0xdafffaf9, 0x01030c00,
+	0x03110200, 0x003f0011
+};
+
+static const u32 aspeed_video_jpeg_dct[ASPEED_VIDEO_JPEG_NUM_QUALITIES]
+				      [ASPEED_VIDEO_JPEG_DCT_SIZE] = {
+	{ 0x0d140043, 0x0c0f110f, 0x11101114, 0x17141516, 0x1e20321e,
+	  0x3d1e1b1b, 0x32242e2b, 0x4b4c3f48, 0x44463f47, 0x61735a50,
+	  0x566c5550, 0x88644644, 0x7a766c65, 0x4d808280, 0x8c978d60,
+	  0x7e73967d, 0xdbff7b80, 0x1f014300, 0x272d2121, 0x3030582d,
+	  0x697bb958, 0xb8b9b97b, 0xb9b8a6a6, 0xb9b9b9b9, 0xb9b9b9b9,
+	  0xb9b9b9b9, 0xb9b9b9b9, 0xb9b9b9b9, 0xb9b9b9b9, 0xb9b9b9b9,
+	  0xb9b9b9b9, 0xb9b9b9b9, 0xb9b9b9b9, 0xffb9b9b9 },
+	{ 0x0c110043, 0x0a0d0f0d, 0x0f0e0f11, 0x14111213, 0x1a1c2b1a,
+	  0x351a1818, 0x2b1f2826, 0x4142373f, 0x3c3d373e, 0x55644e46,
+	  0x4b5f4a46, 0x77573d3c, 0x6b675f58, 0x43707170, 0x7a847b54,
+	  0x6e64836d, 0xdbff6c70, 0x1b014300, 0x22271d1d, 0x2a2a4c27,
+	  0x5b6ba04c, 0xa0a0a06b, 0xa0a0a0a0, 0xa0a0a0a0, 0xa0a0a0a0,
+	  0xa0a0a0a0, 0xa0a0a0a0, 0xa0a0a0a0, 0xa0a0a0a0, 0xa0a0a0a0,
+	  0xa0a0a0a0, 0xa0a0a0a0, 0xa0a0a0a0, 0xffa0a0a0 },
+	{ 0x090e0043, 0x090a0c0a, 0x0c0b0c0e, 0x110e0f10, 0x15172415,
+	  0x2c151313, 0x241a211f, 0x36372e34, 0x31322e33, 0x4653413a,
+	  0x3e4e3d3a, 0x62483231, 0x58564e49, 0x385d5e5d, 0x656d6645,
+	  0x5b536c5a, 0xdbff595d, 0x16014300, 0x1c201818, 0x22223f20,
+	  0x4b58853f, 0x85858558, 0x85858585, 0x85858585, 0x85858585,
+	  0x85858585, 0x85858585, 0x85858585, 0x85858585, 0x85858585,
+	  0x85858585, 0x85858585, 0x85858585, 0xff858585 },
+	{ 0x070b0043, 0x07080a08, 0x0a090a0b, 0x0d0b0c0c, 0x11121c11,
+	  0x23110f0f, 0x1c141a19, 0x2b2b2429, 0x27282428, 0x3842332e,
+	  0x313e302e, 0x4e392827, 0x46443e3a, 0x2c4a4a4a, 0x50565137,
+	  0x48425647, 0xdbff474a, 0x12014300, 0x161a1313, 0x1c1c331a,
+	  0x3d486c33, 0x6c6c6c48, 0x6c6c6c6c, 0x6c6c6c6c, 0x6c6c6c6c,
+	  0x6c6c6c6c, 0x6c6c6c6c, 0x6c6c6c6c, 0x6c6c6c6c, 0x6c6c6c6c,
+	  0x6c6c6c6c, 0x6c6c6c6c, 0x6c6c6c6c, 0xff6c6c6c },
+	{ 0x06090043, 0x05060706, 0x07070709, 0x0a09090a, 0x0d0e160d,
+	  0x1b0d0c0c, 0x16101413, 0x21221c20, 0x1e1f1c20, 0x2b332824,
+	  0x26302624, 0x3d2d1f1e, 0x3735302d, 0x22393a39, 0x3f443f2b,
+	  0x38334338, 0xdbff3739, 0x0d014300, 0x11130e0e, 0x15152613,
+	  0x2d355026, 0x50505035, 0x50505050, 0x50505050, 0x50505050,
+	  0x50505050, 0x50505050, 0x50505050, 0x50505050, 0x50505050,
+	  0x50505050, 0x50505050, 0x50505050, 0xff505050 },
+	{ 0x04060043, 0x03040504, 0x05040506, 0x07060606, 0x09090f09,
+	  0x12090808, 0x0f0a0d0d, 0x16161315, 0x14151315, 0x1d221b18,
+	  0x19201918, 0x281e1514, 0x2423201e, 0x17262726, 0x2a2d2a1c,
+	  0x25222d25, 0xdbff2526, 0x09014300, 0x0b0d0a0a, 0x0e0e1a0d,
+	  0x1f25371a, 0x37373725, 0x37373737, 0x37373737, 0x37373737,
+	  0x37373737, 0x37373737, 0x37373737, 0x37373737, 0x37373737,
+	  0x37373737, 0x37373737, 0x37373737, 0xff373737 },
+	{ 0x02030043, 0x01020202, 0x02020203, 0x03030303, 0x04040704,
+	  0x09040404, 0x07050606, 0x0b0b090a, 0x0a0a090a, 0x0e110d0c,
+	  0x0c100c0c, 0x140f0a0a, 0x1211100f, 0x0b131313, 0x1516150e,
+	  0x12111612, 0xdbff1213, 0x04014300, 0x05060505, 0x07070d06,
+	  0x0f121b0d, 0x1b1b1b12, 0x1b1b1b1b, 0x1b1b1b1b, 0x1b1b1b1b,
+	  0x1b1b1b1b, 0x1b1b1b1b, 0x1b1b1b1b, 0x1b1b1b1b, 0x1b1b1b1b,
+	  0x1b1b1b1b, 0x1b1b1b1b, 0x1b1b1b1b, 0xff1b1b1b },
+	{ 0x01020043, 0x01010101, 0x01010102, 0x02020202, 0x03030503,
+	  0x06030202, 0x05030404, 0x07070607, 0x06070607, 0x090b0908,
+	  0x080a0808, 0x0d0a0706, 0x0c0b0a0a, 0x070c0d0c, 0x0e0f0e09,
+	  0x0c0b0f0c, 0xdbff0c0c, 0x03014300, 0x03040303, 0x04040804,
+	  0x0a0c1208, 0x1212120c, 0x12121212, 0x12121212, 0x12121212,
+	  0x12121212, 0x12121212, 0x12121212, 0x12121212, 0x12121212,
+	  0x12121212, 0x12121212, 0x12121212, 0xff121212 },
+	{ 0x01020043, 0x01010101, 0x01010102, 0x02020202, 0x03030503,
+	  0x06030202, 0x05030404, 0x07070607, 0x06070607, 0x090b0908,
+	  0x080a0808, 0x0d0a0706, 0x0c0b0a0a, 0x070c0d0c, 0x0e0f0e09,
+	  0x0c0b0f0c, 0xdbff0c0c, 0x02014300, 0x03030202, 0x04040703,
+	  0x080a0f07, 0x0f0f0f0a, 0x0f0f0f0f, 0x0f0f0f0f, 0x0f0f0f0f,
+	  0x0f0f0f0f, 0x0f0f0f0f, 0x0f0f0f0f, 0x0f0f0f0f, 0x0f0f0f0f,
+	  0x0f0f0f0f, 0x0f0f0f0f, 0x0f0f0f0f, 0xff0f0f0f },
+	{ 0x01010043, 0x01010101, 0x01010101, 0x01010101, 0x02020302,
+	  0x04020202, 0x03020303, 0x05050405, 0x05050405, 0x07080606,
+	  0x06080606, 0x0a070505, 0x09080807, 0x05090909, 0x0a0b0a07,
+	  0x09080b09, 0xdbff0909, 0x02014300, 0x02030202, 0x03030503,
+	  0x07080c05, 0x0c0c0c08, 0x0c0c0c0c, 0x0c0c0c0c, 0x0c0c0c0c,
+	  0x0c0c0c0c, 0x0c0c0c0c, 0x0c0c0c0c, 0x0c0c0c0c, 0x0c0c0c0c,
+	  0x0c0c0c0c, 0x0c0c0c0c, 0x0c0c0c0c, 0xff0c0c0c },
+	{ 0x01010043, 0x01010101, 0x01010101, 0x01010101, 0x01010201,
+	  0x03010101, 0x02010202, 0x03030303, 0x03030303, 0x04050404,
+	  0x04050404, 0x06050303, 0x06050505, 0x03060606, 0x07070704,
+	  0x06050706, 0xdbff0606, 0x01014300, 0x01020101, 0x02020402,
+	  0x05060904, 0x09090906, 0x09090909, 0x09090909, 0x09090909,
+	  0x09090909, 0x09090909, 0x09090909, 0x09090909, 0x09090909,
+	  0x09090909, 0x09090909, 0x09090909, 0xff090909 },
+	{ 0x01010043, 0x01010101, 0x01010101, 0x01010101, 0x01010101,
+	  0x01010101, 0x01010101, 0x01010101, 0x01010101, 0x02020202,
+	  0x02020202, 0x03020101, 0x03020202, 0x01030303, 0x03030302,
+	  0x03020303, 0xdbff0403, 0x01014300, 0x01010101, 0x01010201,
+	  0x03040602, 0x06060604, 0x06060606, 0x06060606, 0x06060606,
+	  0x06060606, 0x06060606, 0x06060606, 0x06060606, 0x06060606,
+	  0x06060606, 0x06060606, 0x06060606, 0xff060606 }
+};
+
+static void aspeed_video_init_jpeg_table(u32 *table, bool yuv420)
+{
+	int i;
+	unsigned int base;
+
+	for (i = 0; i < ASPEED_VIDEO_JPEG_NUM_QUALITIES; i++) {
+		base = 256 * i;	/* AST HW requires this header spacing */
+		memcpy(&table[base], aspeed_video_jpeg_header,
+		       sizeof(aspeed_video_jpeg_header));
+
+		base += ASPEED_VIDEO_JPEG_HEADER_SIZE;
+		memcpy(&table[base], aspeed_video_jpeg_dct[i],
+		       sizeof(aspeed_video_jpeg_dct[i]));
+
+		base += ASPEED_VIDEO_JPEG_DCT_SIZE;
+		memcpy(&table[base], aspeed_video_jpeg_quant,
+		       sizeof(aspeed_video_jpeg_quant));
+
+		if (yuv420)
+			table[base + 2] = 0x00220103;
+	}
+}
+
+static void aspeed_video_update(struct aspeed_video *video, u32 reg, u32 clear,
+				u32 bits)
+{
+	u32 t = readl(video->base + reg);
+	u32 before = t;
+
+	t &= ~clear;
+	t |= bits;
+	writel(t, video->base + reg);
+	dev_dbg(video->dev, "update %03x[%08x -> %08x]\n", reg, before,
+		readl(video->base + reg));
+}
+
+static u32 aspeed_video_read(struct aspeed_video *video, u32 reg)
+{
+	u32 t = readl(video->base + reg);
+
+	dev_dbg(video->dev, "read %03x[%08x]\n", reg, t);
+	return t;
+}
+
+static void aspeed_video_write(struct aspeed_video *video, u32 reg, u32 val)
+{
+	writel(val, video->base + reg);
+	dev_dbg(video->dev, "write %03x[%08x]\n", reg,
+		readl(video->base + reg));
+}
+
+static bool aspeed_video_engine_busy(struct aspeed_video *video)
+{
+	u32 seq_ctrl = aspeed_video_read(video, VE_SEQ_CTRL);
+
+	if (!(seq_ctrl & VE_SEQ_CTRL_COMP_BUSY) ||
+	    !(seq_ctrl & VE_SEQ_CTRL_CAP_BUSY)) {
+		dev_err(video->dev, "video engine busy\n");
+		return true;
+	}
+
+	return false;
+}
+
+static int aspeed_video_start_frame(struct aspeed_video *video)
+{
+	dma_addr_t addr;
+	unsigned long flags;
+	struct aspeed_video_buffer *buf;
+
+	if (aspeed_video_engine_busy(video))
+		return -EBUSY;
+
+	spin_lock_irqsave(&video->lock, flags);
+	buf = list_first_entry_or_null(&video->buffers,
+				       struct aspeed_video_buffer, link);
+	if (!buf) {
+		spin_unlock_irqrestore(&video->lock, flags);
+		return -EPROTO;
+	}
+
+	set_bit(VIDEO_FRAME_INPRG, &video->flags);
+	addr = vb2_dma_contig_plane_dma_addr(&buf->vb.vb2_buf, 0);
+	spin_unlock_irqrestore(&video->lock, flags);
+
+	aspeed_video_write(video, VE_COMP_PROC_OFFSET, 0);
+	aspeed_video_write(video, VE_COMP_OFFSET, 0);
+	aspeed_video_write(video, VE_COMP_ADDR, addr);
+
+	aspeed_video_update(video, VE_INTERRUPT_CTRL, 0,
+			    VE_INTERRUPT_COMP_COMPLETE |
+			    VE_INTERRUPT_CAPTURE_COMPLETE);
+
+	aspeed_video_update(video, VE_SEQ_CTRL, 0,
+			    VE_SEQ_CTRL_TRIG_CAPTURE | VE_SEQ_CTRL_TRIG_COMP);
+
+	return 0;
+}
+
+static void aspeed_video_start_mode_detect(struct aspeed_video *video)

drivers/media/platform/aspeed-video.c line 466

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+{
+	/* Enable mode detect interrupts */
+	aspeed_video_update(video, VE_INTERRUPT_CTRL, 0,
+			    VE_INTERRUPT_MODE_DETECT);
+
+	/* Trigger mode detect */
+	aspeed_video_update(video, VE_SEQ_CTRL, 0, VE_SEQ_CTRL_TRIG_MODE_DET);
+}
+
+static void aspeed_video_disable_mode_detect(struct aspeed_video *video)

Somewhat weird naming for this pair of functions: either use start/stop or enable/disable (my preference), not start/disable.

Quoted 37 lines
drivers/media/platform/aspeed-video.c new file +37 -0
+{
+	/* Disable mode detect interrupts */
+	aspeed_video_update(video, VE_INTERRUPT_CTRL,
+			    VE_INTERRUPT_MODE_DETECT, 0);
+
+	/* Disable mode detect */
+	aspeed_video_update(video, VE_SEQ_CTRL, VE_SEQ_CTRL_TRIG_MODE_DET, 0);
+}
+
+static void aspeed_video_off(struct aspeed_video *video)
+{
+	/* Reset the engine */
+	reset_control_assert(video->rst);
+	udelay(100);
+	reset_control_deassert(video->rst);
+
+	/* Turn off the relevant clocks */
+	clk_disable_unprepare(video->vclk);
+	clk_disable_unprepare(video->eclk);
+}
+
+static void aspeed_video_on(struct aspeed_video *video)
+{
+	/* Turn on the relevant clocks */
+	clk_prepare_enable(video->eclk);
+	clk_prepare_enable(video->vclk);
+
+	/* Reset the engine */
+	reset_control_assert(video->rst);
+	udelay(100);
+	reset_control_deassert(video->rst);
+}
+
+static void aspeed_video_bufs_done(struct aspeed_video *video,
+				   enum vb2_buffer_state state)
+{
+	unsigned long flags;
Quoted 8 lines

drivers/media/platform/aspeed-video.c line 509

Quoted 6 lines
drivers/media/platform/aspeed-video.c new file +6 -0
+	struct aspeed_video_buffer *buf;
+
+	spin_lock_irqsave(&video->lock, flags);
+	list_for_each_entry(buf, &video->buffers, link) {
+		if (list_is_last(&buf->link, &video->buffers))
+			buf->vb.flags |= V4L2_BUF_FLAG_LAST;

You don't need to use this flag. It's meant for hardware codecs, not for a regular video capture driver.

I mentioned before that dequeue calls hang in an error condition unless this flag is specified. For example if resolution change is detected and application is in the middle of trying to dequeue...

Quoted 121 lines
Quoted 79 lines
drivers/media/platform/aspeed-video.c new file +78 -0
+		vb2_buffer_done(&buf->vb.vb2_buf, state);
+	}
+	INIT_LIST_HEAD(&video->buffers);
+	spin_unlock_irqrestore(&video->lock, flags);
+}
+
+static irqreturn_t aspeed_video_irq(int irq, void *arg)
+{
+	struct aspeed_video *video = arg;
+	u32 sts = aspeed_video_read(video, VE_INTERRUPT_STATUS);
+
+	if (atomic_read(&video->clients) == 0) {
+		dev_info(video->dev, "irq with no client; disabling irqs\n");
+
+		aspeed_video_write(video, VE_INTERRUPT_CTRL, 0);
+		aspeed_video_write(video, VE_INTERRUPT_STATUS, 0xffffffff);
+		return IRQ_HANDLED;
+	}
+
+	/* Resolution changed; reset entire engine and reinitialize */
+	if (sts & VE_INTERRUPT_MODE_DETECT_WD) {
+		dev_info(video->dev, "resolution changed; resetting\n");
+		set_bit(VIDEO_RES_CHANGE, &video->flags);
+		clear_bit(VIDEO_FRAME_INPRG, &video->flags);
+		clear_bit(VIDEO_STREAMING, &video->flags);
+
+		aspeed_video_off(video);
+		aspeed_video_bufs_done(video, VB2_BUF_STATE_ERROR);
+
+		schedule_delayed_work(&video->res_work,
+				      RESOLUTION_CHANGE_DELAY);
+		return IRQ_HANDLED;
+	}
+
+	if (sts & VE_INTERRUPT_MODE_DETECT) {
+		aspeed_video_update(video, VE_INTERRUPT_CTRL,
+				    VE_INTERRUPT_MODE_DETECT, 0);
+		aspeed_video_write(video, VE_INTERRUPT_STATUS,
+				   VE_INTERRUPT_MODE_DETECT);
+
+		set_bit(VIDEO_MODE_DETECT_DONE, &video->flags);
+		wake_up_interruptible_all(&video->wait);
+	}
+
+	if ((sts & VE_INTERRUPT_COMP_COMPLETE) &&
+	    (sts & VE_INTERRUPT_CAPTURE_COMPLETE)) {
+		struct aspeed_video_buffer *buf;
+		u32 frame_size = aspeed_video_read(video,
+						   VE_OFFSET_COMP_STREAM);
+
+		spin_lock(&video->lock);
+		clear_bit(VIDEO_FRAME_INPRG, &video->flags);
+		buf = list_first_entry_or_null(&video->buffers,
+					       struct aspeed_video_buffer,
+					       link);
+		if (buf) {
+			vb2_set_plane_payload(&buf->vb.vb2_buf, 0, frame_size);
+
+			if (!list_is_last(&buf->link, &video->buffers)) {
+				buf->vb.vb2_buf.timestamp = ktime_get_ns();
+				buf->vb.sequence = video->sequence++;
+				buf->vb.field = V4L2_FIELD_NONE;
+				vb2_buffer_done(&buf->vb.vb2_buf,
+						VB2_BUF_STATE_DONE);
+				list_del(&buf->link);
+			}
+		}
+		spin_unlock(&video->lock);
+
+		aspeed_video_update(video, VE_SEQ_CTRL,
+				    VE_SEQ_CTRL_TRIG_CAPTURE |
+				    VE_SEQ_CTRL_FORCE_IDLE |
+				    VE_SEQ_CTRL_TRIG_COMP, 0);
+		aspeed_video_update(video, VE_INTERRUPT_CTRL,
+				    VE_INTERRUPT_COMP_COMPLETE |
+				    VE_INTERRUPT_CAPTURE_COMPLETE, 0);
+		aspeed_video_write(video, VE_INTERRUPT_STATUS,
+				   VE_INTERRUPT_COMP_COMPLETE |

drivers/media/platform/aspeed-video.c line 597

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+				   VE_INTERRUPT_CAPTURE_COMPLETE);
+
+		if (test_bit(VIDEO_STREAMING, &video->flags) && buf)
+			aspeed_video_start_frame(video);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static void aspeed_video_check_polarity(struct aspeed_video *video)

This function should be moved to just before the get_resolution function, since that's the one that calls this.

Quoted 16 lines
drivers/media/platform/aspeed-video.c new file +16 -0
+{
+	int i;
+	int hsync_counter = 0;
+	int vsync_counter = 0;
+	u32 sts;
+
+	for (i = 0; i < NUM_POLARITY_CHECKS; ++i) {
+		sts = aspeed_video_read(video, VE_MODE_DETECT_STATUS);
+		if (sts & VE_MODE_DETECT_STATUS_VSYNC)
+			vsync_counter--;
+		else
+			vsync_counter++;
+
+		if (sts & VE_MODE_DETECT_STATUS_HSYNC)
+			hsync_counter--;
+		else

drivers/media/platform/aspeed-video.c line 623

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+			hsync_counter++;
+	}
+
+	if (hsync_counter < 0 || vsync_counter < 0) {
+		u32 ctrl;
+
+		if (hsync_counter < 0)
+			ctrl = VE_CTRL_HSYNC_POL;
+		else
+			video->timings.polarities |= V4L2_DV_HSYNC_POS_POL;

You should set this for video->detected_timings.
You also don't clear the polarities flag if the polarity is negative.

Quoted 10 lines

drivers/media/platform/aspeed-video.c line 630

Quoted 7 lines
drivers/media/platform/aspeed-video.c new file +7 -0
+
+		if (vsync_counter < 0)
+			ctrl = VE_CTRL_VSYNC_POL;
+		else
+			video->timings.polarities |= V4L2_DV_VSYNC_POS_POL;
+
+		aspeed_video_update(video, VE_CTRL, 0, ctrl);

It would make more sense to write to this register either when you start streaming or when s_dv_timings is called. That's when you need it, not when detecting a new timing.

This is needed here in order to do the second phase of resolution detection.

Quoted 75 lines
Quoted 75 lines
drivers/media/platform/aspeed-video.c new file +74 -0
+	}
+}
+
+static bool aspeed_video_alloc_buf(struct aspeed_video *video,
+				   struct aspeed_video_addr *addr,
+				   unsigned int size)
+{
+	addr->virt = dma_alloc_coherent(video->dev, size, &addr->dma,
+					GFP_KERNEL);
+	if (!addr->virt)
+		return false;
+
+	addr->size = size;
+	return true;
+}
+
+static void aspeed_video_free_buf(struct aspeed_video *video,
+				  struct aspeed_video_addr *addr)
+{
+	dma_free_coherent(video->dev, addr->size, addr->virt, addr->dma);
+	addr->size = 0;
+	addr->dma = 0ULL;
+	addr->virt = NULL;
+}
+
+/*
+ * Get the minimum HW-supported compression buffer size for the frame size.
+ * Assume worst-case JPEG compression size is 1/8 raw size. This should be
+ * plenty even for maximum quality; any worse and the engine will simply return
+ * incomplete JPEGs.
+ */
+static void aspeed_video_calc_compressed_size(struct aspeed_video *video)
+{
+	int i, j;
+	u32 compression_buffer_size_reg = 0;
+	unsigned int size;
+	const unsigned int num_compression_packets = 4;
+	const unsigned int compression_packet_size = 1024;
+	const unsigned int max_compressed_size =
+		video->capture_width * video->capture_height / 2;
+
+	video->max_compressed_size = UINT_MAX;
+
+	for (i = 0; i < 6; ++i) {
+		for (j = 0; j < 8; ++j) {
+			size = (num_compression_packets << i) *
+				(compression_packet_size << j);
+			if (size < max_compressed_size)
+				continue;
+
+			if (size < video->max_compressed_size) {
+				compression_buffer_size_reg = (i << 3) | j;
+				video->max_compressed_size = size;
+			}
+		}
+	}
+
+	aspeed_video_write(video, VE_STREAM_BUF_SIZE,
+			   compression_buffer_size_reg);
+
+	dev_dbg(video->dev, "max compressed size: %x\n",
+		video->max_compressed_size);
+}
+
+#define res_check(v) test_and_clear_bit(VIDEO_MODE_DETECT_DONE, &(v)->flags)
+
+static int aspeed_video_get_resolution(struct aspeed_video *video)
+{
+	bool invalid_resolution = true;
+	int rc;
+	int tries = 0;
+	unsigned int bottom;
+	unsigned int left;
+	unsigned int right;
Quoted 8 lines

drivers/media/platform/aspeed-video.c line 710

Quoted 6 lines
drivers/media/platform/aspeed-video.c new file +6 -0
+	unsigned int top;
+	u32 mds;
+	u32 src_lr_edge;
+	u32 src_tb_edge;
+	u32 sync;
+

If I understand the code correctly, when this is called we're not supposed to be streaming video, right?

Correct.

Quoted 59 lines
Quoted 18 lines
drivers/media/platform/aspeed-video.c new file +17 -0
+	if (video->srcs[1].size)
+		aspeed_video_free_buf(video, &video->srcs[1]);
+
+	if (!video->detect.size) {
+		if (video->srcs[0].size >= VE_MAX_SRC_BUFFER_SIZE) {
+			video->detect = video->srcs[0];
+
+			video->srcs[0].size = 0;
+			video->srcs[0].dma = 0ULL;
+			video->srcs[0].virt = NULL;
+		} else {
+			if (video->srcs[0].size)
+				aspeed_video_free_buf(video, &video->srcs[0]);
+
+			if (!aspeed_video_alloc_buf(video, &video->detect,
+						    VE_MAX_SRC_BUFFER_SIZE)) {
+				dev_err(video->dev,

drivers/media/platform/aspeed-video.c line 737

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+					"failed to allocate source buffers\n");
+				return -ENOMEM;
+			}
+		}
+	}
+
+	aspeed_video_write(video, VE_SRC0_ADDR, video->detect.dma);
+
+	video->timings.width = 0;
+	video->timings.height = 0;

detected_timings

Quoted 16 lines
drivers/media/platform/aspeed-video.c new file +16 -0
+
+	do {
+		if (tries) {
+			set_current_state(TASK_INTERRUPTIBLE);
+			if (schedule_timeout(INVALID_RESOLUTION_DELAY))
+				return -EINTR;
+		}
+
+		aspeed_video_start_mode_detect(video);
+
+		rc = wait_event_interruptible_timeout(video->wait,
+						      res_check(video),
+						      MODE_DETECT_TIMEOUT);
+		if (!rc) {
+			dev_err(video->dev, "timed out on 1st mode detect\n");
+			aspeed_video_disable_mode_detect(video);

drivers/media/platform/aspeed-video.c line 763

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+			return -ETIMEDOUT;
+		}
+
+		/* Disable mode detect in order to re-trigger */
+		aspeed_video_update(video, VE_SEQ_CTRL,
+				    VE_SEQ_CTRL_TRIG_MODE_DET, 0);
+
+		aspeed_video_check_polarity(video);
+
+		aspeed_video_start_mode_detect(video);

Just curious: why is check_polarity done before starting the mode_detect? I would expect it to be the other way around.

Quoted 4 lines

As mentioned above, aspeed_video_check_polarity doesn't just check the polarity, it also seems to set it. If this is required before you can do a mode detect, then that should be documented and the function should be renamed to check_and_set_polarity.

Yep, renamed.

Quoted 53 lines
Quoted 53 lines
drivers/media/platform/aspeed-video.c new file +52 -0
+
+		rc = wait_event_interruptible_timeout(video->wait,
+						      res_check(video),
+						      MODE_DETECT_TIMEOUT);
+		if (!rc) {
+			dev_err(video->dev, "timed out on 2nd mode detect\n");
+			aspeed_video_disable_mode_detect(video);
+			return -ETIMEDOUT;
+		}
+
+		src_lr_edge = aspeed_video_read(video, VE_SRC_LR_EDGE_DET);
+		src_tb_edge = aspeed_video_read(video, VE_SRC_TB_EDGE_DET);
+		mds = aspeed_video_read(video, VE_MODE_DETECT_STATUS);
+		sync = aspeed_video_read(video, VE_SYNC_STATUS);
+
+		bottom = (src_tb_edge & VE_SRC_TB_EDGE_DET_BOT) >>
+			VE_SRC_TB_EDGE_DET_BOT_SHF;
+		top = src_tb_edge & VE_SRC_TB_EDGE_DET_TOP;
+		video->timings.vfrontporch = top;
+		video->timings.vbackporch = ((mds & VE_MODE_DETECT_V_LINES) >>
+			VE_MODE_DETECT_V_LINES_SHF) - bottom;
+		video->timings.vsync = (sync & VE_SYNC_STATUS_VSYNC) >>
+			VE_SYNC_STATUS_VSYNC_SHF;
+		if (top > bottom)
+			continue;
+
+		right = (src_lr_edge & VE_SRC_LR_EDGE_DET_RT) >>
+			VE_SRC_LR_EDGE_DET_RT_SHF;
+		left = src_lr_edge & VE_SRC_LR_EDGE_DET_LEFT;
+		video->timings.hfrontporch = left;
+		video->timings.hbackporch = (mds & VE_MODE_DETECT_H_PIXELS) -
+			right;
+		video->timings.hsync = sync & VE_SYNC_STATUS_HSYNC;
+		if (left > right)
+			continue;
+
+		invalid_resolution = false;
+	} while (invalid_resolution && (tries++ < INVALID_RESOLUTION_RETRIES));
+
+	if (invalid_resolution) {
+		dev_err(video->dev, "invalid resolution detected\n");
+		return -ERANGE;
+	}
+
+	video->timings.height = (bottom - top) + 1;
+	video->timings.width = (right - left) + 1;
+
+	/* Don't use direct mode below 1024 x 768 (irqs don't fire) */
+	if (video->timings.width * video->timings.height < DIRECT_FETCH_THRESHOLD) {
+		aspeed_video_write(video, VE_TGS_0,
+				   FIELD_PREP(VE_TGS_FIRST, left - 1) |
+				   FIELD_PREP(VE_TGS_LAST, right));
Quoted 8 lines

drivers/media/platform/aspeed-video.c line 822

Quoted 7 lines
drivers/media/platform/aspeed-video.c new file +7 -0
+		aspeed_video_write(video, VE_TGS_1,
+				   FIELD_PREP(VE_TGS_FIRST, top) |
+				   FIELD_PREP(VE_TGS_LAST, bottom + 1));
+		aspeed_video_update(video, VE_CTRL, 0, VE_CTRL_INT_DE);
+	} else {
+		aspeed_video_update(video, VE_CTRL, 0, VE_CTRL_DIRECT_FETCH);
+	}

Shouldn't this be done in set_capture_resolution?

Yes.

Quoted 7 lines

drivers/media/platform/aspeed-video.c line 827

Quoted 6 lines
drivers/media/platform/aspeed-video.c new file +5 -0
+
+	aspeed_video_update(video, VE_INTERRUPT_CTRL, 0,
+			    VE_INTERRUPT_MODE_DETECT_WD);
+	aspeed_video_update(video, VE_SEQ_CTRL, 0,
+			    VE_SEQ_CTRL_AUTO_COMP | VE_SEQ_CTRL_EN_WATCHDOG);

What do these two lines do? Perhaps a comment would help.

Sure, will comment; these disable the mode detection "watchdog" in case of error. Then it enables automatic compression after frame capture and enables the resolution change "watchdog".

Quoted 115 lines

drivers/media/platform/aspeed-video.c line 838

Quoted 12 lines
drivers/media/platform/aspeed-video.c new file +11 -0
+
+	dev_dbg(video->dev, "got resolution[%dx%d]\n", video->timings.width,
+		video->timings.height);
+
+	return 0;
+
+}
+
+static int aspeed_video_set_capture_resolution(struct aspeed_video *video)
+{
+	unsigned int size = video->timings.width * video->timings.height;

active_timings

Quoted 101 lines
drivers/media/platform/aspeed-video.c new file +101 -0
+	struct aspeed_video_addr detect = video->detect;
+
+	video->detect.size = 0;
+	video->detect.dma = 0ULL;
+	video->detect.virt = NULL;
+
+	video->capture_width = video->timings.width;
+	video->capture_height = video->timings.height;
+
+	aspeed_video_write(video, VE_CAP_WINDOW,
+			   video->capture_width << 16 | video->capture_height);
+	aspeed_video_write(video, VE_COMP_WINDOW,
+			   video->capture_width << 16 | video->capture_height);
+	aspeed_video_write(video, VE_SRC_SCANLINE_OFFSET,
+			   video->capture_width * 4);
+
+	size *= 4;
+	if (size == detect.size / 2) {
+		aspeed_video_write(video, VE_SRC1_ADDR, detect.dma + size);
+		video->srcs[0] = detect;
+	} else if (size == detect.size) {
+		video->srcs[0] = detect;
+
+		if (!aspeed_video_alloc_buf(video, &video->srcs[1], size))
+			goto err_mem;
+
+		aspeed_video_write(video, VE_SRC1_ADDR, video->srcs[1].dma);
+	} else {
+		aspeed_video_free_buf(video, &detect);
+
+		if (!aspeed_video_alloc_buf(video, &video->srcs[0], size))
+			goto err_mem;
+
+		if (!aspeed_video_alloc_buf(video, &video->srcs[1], size))
+			goto err_mem;
+
+		aspeed_video_write(video, VE_SRC0_ADDR, video->srcs[0].dma);
+		aspeed_video_write(video, VE_SRC1_ADDR, video->srcs[1].dma);
+	}
+
+	aspeed_video_calc_compressed_size(video);
+
+	dev_dbg(video->dev, "set resolution[%dx%d]\n", video->capture_width,
+		video->capture_height);
+
+	return 0;
+
+err_mem:
+	dev_err(video->dev, "failed to allocate source buffers\n");
+
+	if (video->srcs[0].size)
+		aspeed_video_free_buf(video, &video->srcs[0]);
+
+	return -ENOMEM;
+}
+
+static void aspeed_video_init_regs(struct aspeed_video *video)
+{
+	u32 comp_ctrl = VE_COMP_CTRL_RSVD |
+		FIELD_PREP(VE_COMP_CTRL_DCT_LUM, video->jpeg_quality) |
+		FIELD_PREP(VE_COMP_CTRL_DCT_CHR, video->jpeg_quality | 0x10);
+	u32 ctrl = VE_CTRL_AUTO_OR_CURSOR;
+	u32 seq_ctrl = VE_SEQ_CTRL_JPEG_MODE;
+
+	if (video->frame_rate)
+		ctrl |= FIELD_PREP(VE_CTRL_FRC, video->frame_rate);
+
+	if (video->yuv420)
+		seq_ctrl |= VE_SEQ_CTRL_YUV420;
+
+	/* Unlock VE registers */
+	aspeed_video_write(video, VE_PROTECTION_KEY, VE_PROTECTION_KEY_UNLOCK);
+
+	/* Disable interrupts */
+	aspeed_video_write(video, VE_INTERRUPT_CTRL, 0);
+	aspeed_video_write(video, VE_INTERRUPT_STATUS, 0xffffffff);
+
+	/* Clear the offset */
+	aspeed_video_write(video, VE_COMP_PROC_OFFSET, 0);
+	aspeed_video_write(video, VE_COMP_OFFSET, 0);
+
+	aspeed_video_write(video, VE_JPEG_ADDR, video->jpeg.dma);
+
+	/* Set control registers */
+	aspeed_video_write(video, VE_SEQ_CTRL, seq_ctrl);
+	aspeed_video_write(video, VE_CTRL, ctrl);
+	aspeed_video_write(video, VE_COMP_CTRL, comp_ctrl);
+
+	/* Don't downscale */
+	aspeed_video_write(video, VE_SCALING_FACTOR, 0x10001000);
+	aspeed_video_write(video, VE_SCALING_FILTER0, 0x00200000);
+	aspeed_video_write(video, VE_SCALING_FILTER1, 0x00200000);
+	aspeed_video_write(video, VE_SCALING_FILTER2, 0x00200000);
+	aspeed_video_write(video, VE_SCALING_FILTER3, 0x00200000);
+
+	/* Set mode detection defaults */
+	aspeed_video_write(video, VE_MODE_DETECT, 0x22666500);
+}
+
+static int aspeed_video_start(struct aspeed_video *video)
+{
Quoted 8 lines

drivers/media/platform/aspeed-video.c line 946

Quoted 7 lines
drivers/media/platform/aspeed-video.c new file +7 -0
+	int rc;
+
+	aspeed_video_on(video);
+
+	aspeed_video_init_regs(video);
+
+	rc = aspeed_video_get_resolution(video);

No, this shouldn't be called here. Only query_dv_timings should call this.

This is required here in order to know if the host VGA is on; if it's not then we fail to get the resolution and should fail to open the device.

Quoted 14 lines

drivers/media/platform/aspeed-video.c line 956

Quoted 11 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+	if (rc)
+		return rc;
+
+	rc = aspeed_video_set_capture_resolution(video);
+	if (rc)
+		return rc;
+
+	video->pix_fmt.width = video->timings.width;
+	video->pix_fmt.height = video->timings.height;
+	video->pix_fmt.sizeimage = video->max_compressed_size;

You don't set that here: otherwise opening the device node would magically change the format. That's not what should happen.

Quoted 2 lines

The golden rule is that you never change timings and/or format unless explicitly commanded by the application through S_DV_TIMINGS and S_FMT.

aspeed_video_start is only called when the first file descriptor is opened. It seems reasonable to me to set the defaults when starting the device.

Quoted 184 lines
Quoted 170 lines
drivers/media/platform/aspeed-video.c new file +169 -0
+
+	return 0;
+}
+
+static void aspeed_video_stop(struct aspeed_video *video)
+{
+	cancel_delayed_work_sync(&video->res_work);
+
+	aspeed_video_off(video);
+
+	if (video->srcs[0].size)
+		aspeed_video_free_buf(video, &video->srcs[0]);
+
+	if (video->srcs[1].size)
+		aspeed_video_free_buf(video, &video->srcs[1]);
+
+	if (video->detect.size)
+		aspeed_video_free_buf(video, &video->detect);
+
+	video->flags = 0;
+}
+
+static int aspeed_video_querycap(struct file *file, void *fh,
+				 struct v4l2_capability *cap)
+{
+	strscpy(cap->driver, DEVICE_NAME, sizeof(cap->driver));
+	strscpy(cap->card, "Aspeed Video Engine", sizeof(cap->card));
+	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s",
+		 DEVICE_NAME);
+
+	return 0;
+}
+
+static int aspeed_video_enum_format(struct file *file, void *fh,
+				    struct v4l2_fmtdesc *f)
+{
+	if (f->index)
+		return -EINVAL;
+
+	f->pixelformat = V4L2_PIX_FMT_JPEG;
+
+	return 0;
+}
+
+static int aspeed_video_get_format(struct file *file, void *fh,
+				   struct v4l2_format *f)
+{
+	struct aspeed_video *video = video_drvdata(file);
+
+	f->fmt.pix = video->pix_fmt;
+
+	return 0;
+}
+
+static int aspeed_video_enum_input(struct file *file, void *fh,
+				   struct v4l2_input *inp)
+{
+	if (inp->index)
+		return -EINVAL;
+
+	strscpy(inp->name, "Host VGA capture", sizeof(inp->name));
+	inp->type = V4L2_INPUT_TYPE_CAMERA;
+	inp->capabilities = V4L2_IN_CAP_DV_TIMINGS;
+	inp->status = 0;
+
+	return 0;
+}
+
+static int aspeed_video_get_input(struct file *file, void *fh, unsigned int *i)
+{
+	*i = 0;
+
+	return 0;
+}
+
+static int aspeed_video_set_input(struct file *file, void *fh, unsigned int i)
+{
+	if (i)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int aspeed_video_get_parm(struct file *file, void *fh,
+				 struct v4l2_streamparm *a)
+{
+	struct aspeed_video *video = video_drvdata(file);
+
+	a->parm.capture.capability = V4L2_CAP_TIMEPERFRAME;
+	a->parm.capture.readbuffers = 3;
+	a->parm.capture.timeperframe.numerator = 1;
+	if (!video->frame_rate)
+		a->parm.capture.timeperframe.denominator = MAX_FRAME_RATE;
+	else
+		a->parm.capture.timeperframe.denominator = video->frame_rate;
+
+	return 0;
+}
+
+static int aspeed_video_set_parm(struct file *file, void *fh,
+				 struct v4l2_streamparm *a)
+{
+	unsigned int frame_rate = 0;
+	struct aspeed_video *video = video_drvdata(file);
+
+	a->parm.capture.capability = V4L2_CAP_TIMEPERFRAME;
+	a->parm.capture.readbuffers = 3;
+
+	if (a->parm.capture.timeperframe.numerator)
+		frame_rate = a->parm.capture.timeperframe.denominator /
+			a->parm.capture.timeperframe.numerator;
+
+	if (!frame_rate || frame_rate > MAX_FRAME_RATE) {
+		frame_rate = 0;
+		a->parm.capture.timeperframe.denominator = MAX_FRAME_RATE;
+		a->parm.capture.timeperframe.numerator = 1;
+	}
+
+	if (video->frame_rate != frame_rate) {
+		video->frame_rate = frame_rate;
+		aspeed_video_update(video, VE_CTRL, VE_CTRL_FRC,
+				    FIELD_PREP(VE_CTRL_FRC, frame_rate));
+	}
+
+	return 0;
+}
+
+static int aspeed_video_enum_framesizes(struct file *file, void *fh,
+					struct v4l2_frmsizeenum *fsize)
+{
+	struct aspeed_video *video = video_drvdata(file);
+
+	if (fsize->index)
+		return -EINVAL;
+
+	if (fsize->pixel_format != V4L2_PIX_FMT_JPEG)
+		return -EINVAL;
+
+	fsize->discrete.width = video->pix_fmt.width;
+	fsize->discrete.height = video->pix_fmt.height;
+	fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE;
+
+	return 0;
+}
+
+static int aspeed_video_enum_frameintervals(struct file *file, void *fh,
+					    struct v4l2_frmivalenum *fival)
+{
+	struct aspeed_video *video = video_drvdata(file);
+
+	if (fival->index)
+		return -EINVAL;
+
+	if (fival->width != video->timings.width ||
+	    fival->height != video->timings.height)
+		return -EINVAL;
+
+	if (fival->pixel_format != V4L2_PIX_FMT_JPEG)
+		return -EINVAL;
+
+	fival->type = V4L2_FRMIVAL_TYPE_CONTINUOUS;
+
+	fival->stepwise.min.denominator = MAX_FRAME_RATE;
+	fival->stepwise.min.numerator = 1;
+	fival->stepwise.max.denominator = 1;
+	fival->stepwise.max.numerator = 1;
+	fival->stepwise.step = fival->stepwise.max;
+
+	return 0;

drivers/media/platform/aspeed-video.c line 1135

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+}
+
+static int aspeed_video_set_dv_timings(struct file *file, void *fh,
+				       struct v4l2_dv_timings *timings)
+{
+	int rc;
+	struct aspeed_video *video = video_drvdata(file);
+
+	if (video->capture_width == timings->bt.width &&
+	    video->capture_height == timings->bt.height)

Unless I am mistaken, capture_width/height just duplicates video->pix_fmt.width/height. I'd drop capture_width/height and only use pix_fmt.

Quoted 11 lines

drivers/media/platform/aspeed-video.c line 1143

Quoted 8 lines
drivers/media/platform/aspeed-video.c new file +8 -0
+		return 0;
+
+	if (vb2_is_busy(&video->queue))
+		return -EBUSY;
+
+	if (video->timings.width != timings->bt.width ||
+	    video->timings.height != timings->bt.height)
+		return -EINVAL;

This 'if' makes no sense. It is perfectly fine (if silly) to set timings that do not match the current resolution. The timings can change at any time anyway, so there is no point to check this.

OK I'll drop it, but I really see no reason to support setting a resolution that will result in either wasted memory or a partial JPEG...

Quoted 224 lines
Quoted 12 lines
drivers/media/platform/aspeed-video.c new file +11 -0
+
+	rc = aspeed_video_set_capture_resolution(video);
+	if (rc)
+		return rc;
+
+	video->pix_fmt.width = timings->bt.width;
+	video->pix_fmt.height = timings->bt.height;
+	video->pix_fmt.sizeimage = video->max_compressed_size;
+
+	timings->type = V4L2_DV_BT_656_1120;
+

drivers/media/platform/aspeed-video.c line 1164

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+	return 0;
+}
+
+static int aspeed_video_get_dv_timings(struct file *file, void *fh,
+				       struct v4l2_dv_timings *timings)
+{
+	struct aspeed_video *video = video_drvdata(file);
+
+	timings->type = V4L2_DV_BT_656_1120;
+	timings->bt = video->timings;

Should return active_timings.

Quoted 15 lines
drivers/media/platform/aspeed-video.c new file +15 -0
+
+	return 0;
+}
+
+static int aspeed_video_query_dv_timings(struct file *file, void *fh,
+					 struct v4l2_dv_timings *timings)
+{
+	int rc;
+	struct aspeed_video *video = video_drvdata(file);
+
+	if (file->f_flags & O_NONBLOCK) {
+		if (test_bit(VIDEO_RES_CHANGE, &video->flags))
+			return -EAGAIN;
+	} else {
+		rc = wait_event_interruptible(video->wait,

drivers/media/platform/aspeed-video.c line 1189

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+					      !test_bit(VIDEO_RES_CHANGE,
+							&video->flags));
+		if (rc)
+			return -EINTR;
+	}
+
+	timings->type = V4L2_DV_BT_656_1120;
+	timings->bt = video->timings;
+	timings->bt.width = video->timings.width;
+	timings->bt.height = video->timings.height;

Should return the detected_timings.

Why assign bt.width/height again? Those two lines can be dropped.

Quoted 12 lines
drivers/media/platform/aspeed-video.c new file +12 -0
+
+	return 0;
+}
+
+static int aspeed_video_enum_dv_timings(struct file *file, void *fh,
+					struct v4l2_enum_dv_timings *timings)
+{
+	if (timings->index)
+		return -EINVAL;
+
+	return aspeed_video_get_dv_timings(file, fh, &timings->timings);
+}

drivers/media/platform/aspeed-video.c line 1211

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+
+static int aspeed_video_dv_timings_cap(struct file *file, void *fh,
+				       struct v4l2_dv_timings_cap *cap)
+{
+	cap->type = V4L2_DV_BT_656_1120;
+	cap->bt.capabilities = V4L2_DV_BT_CAP_PROGRESSIVE;
+	cap->bt.min_width = MIN_WIDTH;
+	cap->bt.max_width = MAX_WIDTH;
+	cap->bt.min_height = MIN_HEIGHT;
+	cap->bt.max_height = MAX_HEIGHT;

I would create a static const struct v4l2_dv_timings_cap at the top of the source and return that here.

You can then use the helpers v4l2_valid_dv_timings in s_dv_timings and v4l2_enum_dv_timings_cap in enum_dv_timings.

You need to set the V4L2_DV_BT_CAP_REDUCED_BLANKING capability as well. And fill in cap->bt.min/max_pixelclock and standards (CEA861|DMT|CVT|GTF).

Quoted 140 lines
drivers/media/platform/aspeed-video.c new file +140 -0
+
+	return 0;
+}
+
+static int aspeed_video_sub_event(struct v4l2_fh *fh,
+				  const struct v4l2_event_subscription *sub)
+{
+	switch (sub->type) {
+	case V4L2_EVENT_SOURCE_CHANGE:
+		return v4l2_src_change_event_subscribe(fh, sub);
+	}
+
+	return v4l2_ctrl_subscribe_event(fh, sub);
+}
+
+static const struct v4l2_ioctl_ops aspeed_video_ioctl_ops = {
+	.vidioc_querycap = aspeed_video_querycap,
+
+	.vidioc_enum_fmt_vid_cap = aspeed_video_enum_format,
+	.vidioc_g_fmt_vid_cap = aspeed_video_get_format,
+	.vidioc_s_fmt_vid_cap = aspeed_video_get_format,
+	.vidioc_try_fmt_vid_cap = aspeed_video_get_format,
+
+	.vidioc_reqbufs = vb2_ioctl_reqbufs,
+	.vidioc_querybuf = vb2_ioctl_querybuf,
+	.vidioc_qbuf = vb2_ioctl_qbuf,
+	.vidioc_dqbuf = vb2_ioctl_dqbuf,
+	.vidioc_create_bufs = vb2_ioctl_create_bufs,
+	.vidioc_prepare_buf = vb2_ioctl_prepare_buf,
+	.vidioc_streamon = vb2_ioctl_streamon,
+	.vidioc_streamoff = vb2_ioctl_streamoff,
+
+	.vidioc_enum_input = aspeed_video_enum_input,
+	.vidioc_g_input = aspeed_video_get_input,
+	.vidioc_s_input = aspeed_video_set_input,
+
+	.vidioc_g_parm = aspeed_video_get_parm,
+	.vidioc_s_parm = aspeed_video_set_parm,
+	.vidioc_enum_framesizes = aspeed_video_enum_framesizes,
+	.vidioc_enum_frameintervals = aspeed_video_enum_frameintervals,
+
+	.vidioc_s_dv_timings = aspeed_video_set_dv_timings,
+	.vidioc_g_dv_timings = aspeed_video_get_dv_timings,
+	.vidioc_query_dv_timings = aspeed_video_query_dv_timings,
+	.vidioc_enum_dv_timings = aspeed_video_enum_dv_timings,
+	.vidioc_dv_timings_cap = aspeed_video_dv_timings_cap,
+
+	.vidioc_subscribe_event = aspeed_video_sub_event,
+	.vidioc_unsubscribe_event = v4l2_event_unsubscribe,
+};
+
+static void aspeed_video_update_jpeg_quality(struct aspeed_video *video)
+{
+	u32 comp_ctrl = FIELD_PREP(VE_COMP_CTRL_DCT_LUM, video->jpeg_quality) |
+		FIELD_PREP(VE_COMP_CTRL_DCT_CHR, video->jpeg_quality | 0x10);
+
+	aspeed_video_update(video, VE_COMP_CTRL,
+			    VE_COMP_CTRL_DCT_LUM | VE_COMP_CTRL_DCT_CHR,
+			    comp_ctrl);
+}
+
+static void aspeed_video_update_subsampling(struct aspeed_video *video)
+{
+	if (video->jpeg.virt)
+		aspeed_video_init_jpeg_table(video->jpeg.virt, video->yuv420);
+
+	if (video->yuv420)
+		aspeed_video_update(video, VE_SEQ_CTRL, 0, VE_SEQ_CTRL_YUV420);
+	else
+		aspeed_video_update(video, VE_SEQ_CTRL, VE_SEQ_CTRL_YUV420, 0);
+}
+
+static int aspeed_video_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct aspeed_video *video = container_of(ctrl->handler,
+						  struct aspeed_video,
+						  ctrl_handler);
+
+	switch (ctrl->id) {
+	case V4L2_CID_JPEG_COMPRESSION_QUALITY:
+		video->jpeg_quality = ctrl->val;
+		aspeed_video_update_jpeg_quality(video);
+		break;
+	case V4L2_CID_JPEG_CHROMA_SUBSAMPLING:
+		if (ctrl->val == V4L2_JPEG_CHROMA_SUBSAMPLING_420) {
+			video->yuv420 = true;
+			aspeed_video_update_subsampling(video);
+		} else {
+			video->yuv420 = false;
+			aspeed_video_update_subsampling(video);
+		}
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static const struct v4l2_ctrl_ops aspeed_video_ctrl_ops = {
+	.s_ctrl = aspeed_video_set_ctrl,
+};
+
+static void aspeed_video_resolution_work(struct work_struct *work)
+{
+	int rc;
+	struct delayed_work *dwork = to_delayed_work(work);
+	struct aspeed_video *video = container_of(dwork, struct aspeed_video,
+						  res_work);
+
+	/* No clients remaining after delay */
+	if (atomic_read(&video->clients) == 0)
+		goto done;
+
+	aspeed_video_on(video);
+
+	aspeed_video_init_regs(video);
+
+	rc = aspeed_video_get_resolution(video);
+	if (rc)
+		dev_err(video->dev,
+			"resolution changed; couldn't get new resolution\n");
+
+	if (video->timings.width != video->pix_fmt.width ||
+	    video->timings.height != video->pix_fmt.height) {
+		static const struct v4l2_event ev = {
+			.type = V4L2_EVENT_SOURCE_CHANGE,
+			.u.src_change.changes = V4L2_EVENT_SRC_CH_RESOLUTION,
+		};
+
+		v4l2_event_queue(&video->vdev, &ev);
+	}
+
+done:
+	clear_bit(VIDEO_RES_CHANGE, &video->flags);
+	wake_up_interruptible_all(&video->wait);
+}
+
+static int aspeed_video_open(struct file *file)
+{
Quoted 8 lines

drivers/media/platform/aspeed-video.c line 1357

Quoted 6 lines
drivers/media/platform/aspeed-video.c new file +6 -0
+	int rc;
+	struct aspeed_video *video = video_drvdata(file);
+
+	mutex_lock(&video->video_lock);
+
+	if (atomic_inc_return(&video->clients) == 1) {

No need for a clients refcount. You can use the v4l2_fh_is_singular(_file) helpers. See how other drivers do this.

I'd quite like to keep this actually, as it's important to know if we have any clients left in the resolution work function; v4l2_is_singular wouldn't help there.

Thanks for all the suggestions! Will incorporate the rest in v6. Eddie

Quoted 360 lines
Quoted 346 lines
drivers/media/platform/aspeed-video.c new file +344 -0
+		rc = aspeed_video_start(video);
+		if (rc) {
+			dev_err(video->dev, "Failed to start video engine\n");
+			atomic_dec(&video->clients);
+			mutex_unlock(&video->video_lock);
+			return rc;
+		}
+	}
+
+	mutex_unlock(&video->video_lock);
+
+	return v4l2_fh_open(file);
+}
+
+static int aspeed_video_release(struct file *file)
+{
+	int rc;
+	struct aspeed_video *video = video_drvdata(file);
+
+	rc = vb2_fop_release(file);
+
+	mutex_lock(&video->video_lock);
+
+	if (atomic_dec_return(&video->clients) == 0)
+		aspeed_video_stop(video);
+
+	mutex_unlock(&video->video_lock);
+
+	return rc;
+}
+
+static const struct v4l2_file_operations aspeed_video_v4l2_fops = {
+	.owner = THIS_MODULE,
+	.read = vb2_fop_read,
+	.poll = vb2_fop_poll,
+	.unlocked_ioctl = video_ioctl2,
+	.mmap = vb2_fop_mmap,
+	.open = aspeed_video_open,
+	.release = aspeed_video_release,
+};
+
+static int aspeed_video_queue_setup(struct vb2_queue *q,
+				    unsigned int *num_buffers,
+				    unsigned int *num_planes,
+				    unsigned int sizes[],
+				    struct device *alloc_devs[])
+{
+	struct aspeed_video *video = vb2_get_drv_priv(q);
+
+	if (*num_planes) {
+		if (sizes[0] < video->max_compressed_size)
+			return -EINVAL;
+
+		return 0;
+	}
+
+	*num_planes = 1;
+	sizes[0] = video->max_compressed_size;
+
+	return 0;
+}
+
+static int aspeed_video_buf_prepare(struct vb2_buffer *vb)
+{
+	struct aspeed_video *video = vb2_get_drv_priv(vb->vb2_queue);
+
+	if (vb2_plane_size(vb, 0) < video->max_compressed_size)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int aspeed_video_start_streaming(struct vb2_queue *q,
+					unsigned int count)
+{
+	int rc;
+	struct aspeed_video *video = vb2_get_drv_priv(q);
+
+	rc = aspeed_video_start_frame(video);
+	if (rc) {
+		aspeed_video_bufs_done(video, VB2_BUF_STATE_QUEUED);
+		return rc;
+	}
+
+	video->sequence = 0;
+	set_bit(VIDEO_STREAMING, &video->flags);
+	return 0;
+}
+
+static void aspeed_video_stop_streaming(struct vb2_queue *q)
+{
+	int rc;
+	struct aspeed_video *video = vb2_get_drv_priv(q);
+
+	clear_bit(VIDEO_STREAMING, &video->flags);
+
+	rc = wait_event_timeout(video->wait,
+				!test_bit(VIDEO_FRAME_INPRG, &video->flags),
+				STOP_TIMEOUT);
+	if (!rc) {
+		dev_err(video->dev, "Timed out when stopping streaming\n");
+		aspeed_video_stop(video);
+	}
+
+	aspeed_video_bufs_done(video, VB2_BUF_STATE_ERROR);
+}
+
+static void aspeed_video_buf_queue(struct vb2_buffer *vb)
+{
+	struct aspeed_video *video = vb2_get_drv_priv(vb->vb2_queue);
+	struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb);
+	struct aspeed_video_buffer *avb = to_aspeed_video_buffer(vbuf);
+	unsigned long flags;
+
+	spin_lock_irqsave(&video->lock, flags);
+	list_add_tail(&avb->link, &video->buffers);
+	spin_unlock_irqrestore(&video->lock, flags);
+}
+
+static const struct vb2_ops aspeed_video_vb2_ops = {
+	.queue_setup = aspeed_video_queue_setup,
+	.wait_prepare = vb2_ops_wait_prepare,
+	.wait_finish = vb2_ops_wait_finish,
+	.buf_prepare = aspeed_video_buf_prepare,
+	.start_streaming = aspeed_video_start_streaming,
+	.stop_streaming = aspeed_video_stop_streaming,
+	.buf_queue =  aspeed_video_buf_queue,
+};
+
+static int aspeed_video_setup_video(struct aspeed_video *video)
+{
+	const u64 mask = ~(BIT(V4L2_JPEG_CHROMA_SUBSAMPLING_444) |
+			   BIT(V4L2_JPEG_CHROMA_SUBSAMPLING_420));
+	struct v4l2_device *v4l2_dev = &video->v4l2_dev;
+	struct vb2_queue *vbq = &video->queue;
+	struct video_device *vdev = &video->vdev;
+	int rc;
+
+	video->pix_fmt.pixelformat = V4L2_PIX_FMT_JPEG;
+	video->pix_fmt.field = V4L2_FIELD_NONE;
+	video->pix_fmt.colorspace = V4L2_COLORSPACE_SRGB;
+	video->pix_fmt.quantization = V4L2_QUANTIZATION_FULL_RANGE;
+
+	rc = v4l2_device_register(video->dev, v4l2_dev);
+	if (rc) {
+		dev_err(video->dev, "Failed to register v4l2 device\n");
+		return rc;
+	}
+
+	v4l2_ctrl_handler_init(&video->ctrl_handler, 2);
+	v4l2_ctrl_new_std(&video->ctrl_handler, &aspeed_video_ctrl_ops,
+			  V4L2_CID_JPEG_COMPRESSION_QUALITY, 0,
+			  ASPEED_VIDEO_JPEG_NUM_QUALITIES - 1, 1, 0);
+	v4l2_ctrl_new_std_menu(&video->ctrl_handler, &aspeed_video_ctrl_ops,
+			       V4L2_CID_JPEG_CHROMA_SUBSAMPLING,
+			       V4L2_JPEG_CHROMA_SUBSAMPLING_420, mask,
+			       V4L2_JPEG_CHROMA_SUBSAMPLING_444);
+
+	if (video->ctrl_handler.error) {
+		v4l2_ctrl_handler_free(&video->ctrl_handler);
+		v4l2_device_unregister(v4l2_dev);
+
+		dev_err(video->dev, "Failed to init controls: %d\n",
+			video->ctrl_handler.error);
+		return rc;
+	}
+
+	v4l2_dev->ctrl_handler = &video->ctrl_handler;
+
+	vbq->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
+	vbq->io_modes = VB2_MMAP | VB2_READ | VB2_DMABUF;
+	vbq->dev = v4l2_dev->dev;
+	vbq->lock = &video->video_lock;
+	vbq->ops = &aspeed_video_vb2_ops;
+	vbq->mem_ops = &vb2_dma_contig_memops;
+	vbq->drv_priv = video;
+	vbq->buf_struct_size = sizeof(struct aspeed_video_buffer);
+	vbq->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC;
+	vbq->min_buffers_needed = 3;
+
+	rc = vb2_queue_init(vbq);
+	if (rc) {
+		v4l2_ctrl_handler_free(&video->ctrl_handler);
+		v4l2_device_unregister(v4l2_dev);
+
+		dev_err(video->dev, "Failed to init vb2 queue\n");
+		return rc;
+	}
+
+	vdev->queue = vbq;
+	vdev->fops = &aspeed_video_v4l2_fops;
+	vdev->device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_READWRITE |
+		V4L2_CAP_STREAMING;
+	vdev->v4l2_dev = v4l2_dev;
+	strscpy(vdev->name, DEVICE_NAME, sizeof(vdev->name));
+	vdev->vfl_type = VFL_TYPE_GRABBER;
+	vdev->vfl_dir = VFL_DIR_RX;
+	vdev->release = video_device_release_empty;
+	vdev->ioctl_ops = &aspeed_video_ioctl_ops;
+	vdev->lock = &video->video_lock;
+
+	video_set_drvdata(vdev, video);
+	rc = video_register_device(vdev, VFL_TYPE_GRABBER, 0);
+	if (rc) {
+		vb2_queue_release(vbq);
+		v4l2_ctrl_handler_free(&video->ctrl_handler);
+		v4l2_device_unregister(v4l2_dev);
+
+		dev_err(video->dev, "Failed to register video device\n");
+		return rc;
+	}
+
+	return 0;
+}
+
+static int aspeed_video_init(struct aspeed_video *video)
+{
+	int irq;
+	int rc;
+	struct device *dev = video->dev;
+
+	irq = irq_of_parse_and_map(dev->of_node, 0);
+	if (!irq) {
+		dev_err(dev, "Unable to find IRQ\n");
+		return -ENODEV;
+	}
+
+	rc = devm_request_irq(dev, irq, aspeed_video_irq, IRQF_SHARED,
+			      DEVICE_NAME, video);
+	if (rc < 0) {
+		dev_err(dev, "Unable to request IRQ %d\n", irq);
+		return rc;
+	}
+
+	video->eclk = devm_clk_get(dev, "eclk");
+	if (IS_ERR(video->eclk)) {
+		dev_err(dev, "Unable to get ECLK\n");
+		return PTR_ERR(video->eclk);
+	}
+
+	video->vclk = devm_clk_get(dev, "vclk");
+	if (IS_ERR(video->vclk)) {
+		dev_err(dev, "Unable to get VCLK\n");
+		return PTR_ERR(video->vclk);
+	}
+
+	video->rst = devm_reset_control_get_exclusive(dev, NULL);
+	if (IS_ERR(video->rst)) {
+		dev_err(dev, "Unable to get VE reset\n");
+		return PTR_ERR(video->rst);
+	}
+
+	rc = of_reserved_mem_device_init(dev);
+	if (rc) {
+		dev_err(dev, "Unable to reserve memory\n");
+		return rc;
+	}
+
+	rc = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
+	if (rc) {
+		dev_err(dev, "Failed to set DMA mask\n");
+		of_reserved_mem_device_release(dev);
+		return rc;
+	}
+
+	if (!aspeed_video_alloc_buf(video, &video->jpeg,
+				    VE_JPEG_HEADER_SIZE)) {
+		dev_err(dev, "Failed to allocate DMA for JPEG header\n");
+		of_reserved_mem_device_release(dev);
+		return rc;
+	}
+
+	aspeed_video_init_jpeg_table(video->jpeg.virt, video->yuv420);
+
+	return 0;
+}
+
+static int aspeed_video_probe(struct platform_device *pdev)
+{
+	int rc;
+	struct resource *res;
+	struct aspeed_video *video = kzalloc(sizeof(*video), GFP_KERNEL);
+
+	if (!video)
+		return -ENOMEM;
+
+	video->frame_rate = 30;
+	video->dev = &pdev->dev;
+	mutex_init(&video->video_lock);
+	init_waitqueue_head(&video->wait);
+	INIT_DELAYED_WORK(&video->res_work, aspeed_video_resolution_work);
+	INIT_LIST_HEAD(&video->buffers);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+	video->base = devm_ioremap_resource(video->dev, res);
+
+	if (IS_ERR(video->base))
+		return PTR_ERR(video->base);
+
+	rc = aspeed_video_init(video);
+	if (rc)
+		return rc;
+
+	rc = aspeed_video_setup_video(video);
+	if (rc)
+		return rc;
+
+	return 0;
+}
+
+static int aspeed_video_remove(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct v4l2_device *v4l2_dev = dev_get_drvdata(dev);
+	struct aspeed_video *video = to_aspeed_video(v4l2_dev);
+
+	video_unregister_device(&video->vdev);
+
+	vb2_queue_release(&video->queue);
+
+	v4l2_ctrl_handler_free(&video->ctrl_handler);
+
+	v4l2_device_unregister(v4l2_dev);
+
+	dma_free_coherent(video->dev, VE_JPEG_HEADER_SIZE, video->jpeg.virt,
+			  video->jpeg.dma);
+
+	of_reserved_mem_device_release(dev);
+
+	return 0;
+}
+
+static const struct of_device_id aspeed_video_of_match[] = {
+	{ .compatible = "aspeed,ast2400-video-engine" },
+	{ .compatible = "aspeed,ast2500-video-engine" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, aspeed_video_of_match);
+
+static struct platform_driver aspeed_video_driver = {
+	.driver = {
+		.name = DEVICE_NAME,
+		.of_match_table = aspeed_video_of_match,

drivers/media/platform/aspeed-video.c line 1711

Quoted 10 lines
drivers/media/platform/aspeed-video.c new file +10 -0
+	},
+	.probe = aspeed_video_probe,
+	.remove = aspeed_video_remove,
+};
+
+module_platform_driver(aspeed_video_driver);
+
+MODULE_DESCRIPTION("ASPEED Video Engine Driver");
+MODULE_AUTHOR("Eddie James");
+MODULE_LICENSE("GPL v2");

Regards,

Hans

#5 lore raw
In reply to Eddie James
Quoted 10 lines · Eddie James

From: Eddie James <[email protected]>

The Video Engine (VE) embedded in the Aspeed AST2400 and AST2500 SOCs can capture and compress video data from digital or analog sources. With the Aspeed chip acting as a service processor, the Video Engine can capture the host processor graphics output.

This series adds a V4L2 driver for the VE, providing the usual V4L2 streaming interface by way of videobuf2. Each frame, the driver triggers the hardware to capture the host graphics output and compress it to JPEG format.

I reviewed the driver, and there is still confusion about active timings and detected timings. You are really close, but it is still not right.

The timings returned by G_DV_TIMINGS should never change, unless by calling S_DV_TIMINGS. The format returned by G_FMT should never change, unless by calling S_DV_TIMINGS (which implicitly changes the format) or S_FMT.

Timings changes from the video or calling QUERY_DV_TIMINGS should have NO effect on the timings/format returned by G_DV_TIMINGS/G_FMT.

Obviously, if the video timings change, then streaming will halt and an event is issued so userspace can take action.

Quoted 4 lines

v4l-utils HEAD dd3ff81f58c4e1e6f33765dc61ad33c48ae6bb07

v4l2-compliance SHA: not available, 32 bits

<snip>

Quoted 6 lines

Control ioctls (Input 0):
test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
test VIDIOC_QUERYCTRL: OK
test VIDIOC_G/S_CTRL: OK
test VIDIOC_G/S/TRY_EXT_CTRLS: OK
fail: v4l2-test-controls.cpp(823): failed to find event for control 'Chroma Subsampling'

That's weird. It's not clear to me why this fails.

Quoted 16 lines

test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) Standard Controls: 3 Private Controls: 0

Format ioctls (Input 0):
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK test VIDIOC_G/S_PARM: OK
test VIDIOC_G_FBUF: OK (Not Supported) test VIDIOC_G_FMT: OK
test VIDIOC_TRY_FMT: OK
test VIDIOC_S_FMT: OK
test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) test Cropping: OK (Not Supported)
test Composing: OK (Not Supported)
test Scaling: OK (Not Supported)

Quoted 7 lines

Codec ioctls (Input 0):
test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) test VIDIOC_G_ENC_INDEX: OK (Not Supported) test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)

Buffer ioctls (Input 0):

		fail: v4l2-test-buffers.cpp(422): dmabuf_valid ^ !!(caps & V4L2_BUF_CAP_SUPPORTS_DMABUF)

I updated v4l2-compliance, as this test was a bit too strict.

Quoted 5 lines

test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: FAIL test VIDIOC_EXPBUF: OK (Not Supported)

Test input 0:

Quoted 7 lines

Streaming ioctls:
test read/write: OK
test blocking wait: OK
test MMAP: OK
test USERPTR: OK (Not Supported)
fail: v4l2-test-buffers.cpp(1102): exp_q.reqbufs(expbuf_node, q.g_buffers())
fail: v4l2-test-buffers.cpp(1192): setupDmaBuf(expbuf_node, node, q, exp_q)

You need to add:

.vidioc_expbuf = vb2_ioctl_expbuf,

to aspeed_video_ioctl_ops.

Quoted 7 lines

test DMABUF: FAIL

Total: 48, Succeeded: 45, Failed: 3, Warnings: 0

The apparent rate of change to the v4l2/vb2 API makes it difficult to pass these tests. None of the failing tests even ran last time I submitted my series. And V4L2_BUF_CAP_SUPPORTS_DMABUF is undefined in 4.19.

When developing new drivers you should use the master branch of
https://git.linuxtv.org/media_tree.git/

The v4l-utils repo is kept in sync with the latest code from that master branch.

Regards,

Hans

Quoted 47 lines

Changes since v4:
- Set real min and max resolution in enum_dv_timings
- Add check for vb2_is_busy before settings the timings
- Set max frame rate to the actual max rather than max + 1
- Correct the input status to 0.
- Rework resolution change to only set the relevant h/w regs during startup or when set_timings is called.

Changes since v3:
- Switch update reg function to use u32 clear rather than unsigned long mask
- Add timing information from host VGA signal
- Fix binding documentation mispelling
- Fix upper case hex values
- Add wait_prepare and wait_finish
- Set buffer state to queued (rather than error) if streaming fails to start
- Switch engine busy print statement to error
- Removed a couple unecessary type assignments in v4l2 ioctls
- Added query_dv_timings, fixed get_dv_timings
- Corrected source change event to fire if and only if size actually changes
- Locked open and release

Changes since v2:
- Switch to streaming interface. This involved a lot of changes.
- Rework memory allocation due to using videobuf2 buffers, but also only allocate the necessary size of source buffer rather than the max size

Changes since v1:
- Removed le32_to_cpu calls for JPEG header data
- Reworked v4l2 ioctls to be compliant.
- Added JPEG controls
- Updated devicetree docs according to Rob's suggestions.
- Added myself to MAINTAINERS

Eddie James (2):
dt-bindings: media: Add Aspeed Video Engine binding documentation
media: platform: Add Aspeed Video Engine driver

 .../devicetree/bindings/media/aspeed-video.txt     |   26 +
 MAINTAINERS                                        |    8 +
 drivers/media/platform/Kconfig                     |    9 +
 drivers/media/platform/Makefile                    |    1 +
 drivers/media/platform/aspeed-video.c              | 1711 ++++++++++++++++++++
 5 files changed, 1755 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/aspeed-video.txt
 create mode 100644 drivers/media/platform/aspeed-video.c
#6 lore raw
Quoted 32 lines · Hans Verkuil
Quoted 10 lines · Eddie James

From: Eddie James <[email protected]>

The Video Engine (VE) embedded in the Aspeed AST2400 and AST2500 SOCs can capture and compress video data from digital or analog sources. With the Aspeed chip acting as a service processor, the Video Engine can capture the host processor graphics output.

This series adds a V4L2 driver for the VE, providing the usual V4L2 streaming interface by way of videobuf2. Each frame, the driver triggers the hardware to capture the host graphics output and compress it to JPEG format.

I reviewed the driver, and there is still confusion about active timings and detected timings. You are really close, but it is still not right.

The timings returned by G_DV_TIMINGS should never change, unless by calling S_DV_TIMINGS. The format returned by G_FMT should never change, unless by calling S_DV_TIMINGS (which implicitly changes the format) or S_FMT.

Timings changes from the video or calling QUERY_DV_TIMINGS should have NO effect on the timings/format returned by G_DV_TIMINGS/G_FMT.

Obviously, if the video timings change, then streaming will halt and an event is issued so userspace can take action.

Quoted 4 lines

v4l-utils HEAD dd3ff81f58c4e1e6f33765dc61ad33c48ae6bb07

v4l2-compliance SHA: not available, 32 bits

<snip>

Quoted 8 lines
Quoted 6 lines

Control ioctls (Input 0):
test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
test VIDIOC_QUERYCTRL: OK
test VIDIOC_G/S_CTRL: OK
test VIDIOC_G/S/TRY_EXT_CTRLS: OK
fail: v4l2-test-controls.cpp(823): failed to find event for control 'Chroma Subsampling'

That's weird. It's not clear to me why this fails.

Ah, this is caused by a bug in our tree. It's fixed by this patch:

https://patchwork.linuxtv.org/patch/52790/

Regards,

Hans

Quoted 111 lines
Quoted 17 lines

test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) Standard Controls: 3 Private Controls: 0

Format ioctls (Input 0):
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK test VIDIOC_G/S_PARM: OK
test VIDIOC_G_FBUF: OK (Not Supported) test VIDIOC_G_FMT: OK
test VIDIOC_TRY_FMT: OK
test VIDIOC_S_FMT: OK
test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) test Cropping: OK (Not Supported)
test Composing: OK (Not Supported)
test Scaling: OK (Not Supported)

Quoted 7 lines

Codec ioctls (Input 0):
test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) test VIDIOC_G_ENC_INDEX: OK (Not Supported) test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)

Buffer ioctls (Input 0):

		fail: v4l2-test-buffers.cpp(422): dmabuf_valid ^ !!(caps & V4L2_BUF_CAP_SUPPORTS_DMABUF)

I updated v4l2-compliance, as this test was a bit too strict.

Quoted 5 lines

test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: FAIL test VIDIOC_EXPBUF: OK (Not Supported)

Test input 0:

Quoted 7 lines

Streaming ioctls:
test read/write: OK
test blocking wait: OK
test MMAP: OK
test USERPTR: OK (Not Supported)
fail: v4l2-test-buffers.cpp(1102): exp_q.reqbufs(expbuf_node, q.g_buffers())
fail: v4l2-test-buffers.cpp(1192): setupDmaBuf(expbuf_node, node, q, exp_q)

You need to add:

.vidioc_expbuf = vb2_ioctl_expbuf,

to aspeed_video_ioctl_ops.

Quoted 7 lines

test DMABUF: FAIL

Total: 48, Succeeded: 45, Failed: 3, Warnings: 0

The apparent rate of change to the v4l2/vb2 API makes it difficult to pass these tests. None of the failing tests even ran last time I submitted my series. And V4L2_BUF_CAP_SUPPORTS_DMABUF is undefined in 4.19.

When developing new drivers you should use the master branch of
https://git.linuxtv.org/media_tree.git/

The v4l-utils repo is kept in sync with the latest code from that master branch.

Regards,

Hans

Quoted 47 lines

Changes since v4:
- Set real min and max resolution in enum_dv_timings
- Add check for vb2_is_busy before settings the timings
- Set max frame rate to the actual max rather than max + 1
- Correct the input status to 0.
- Rework resolution change to only set the relevant h/w regs during startup or when set_timings is called.

Changes since v3:
- Switch update reg function to use u32 clear rather than unsigned long mask
- Add timing information from host VGA signal
- Fix binding documentation mispelling
- Fix upper case hex values
- Add wait_prepare and wait_finish
- Set buffer state to queued (rather than error) if streaming fails to start
- Switch engine busy print statement to error
- Removed a couple unecessary type assignments in v4l2 ioctls
- Added query_dv_timings, fixed get_dv_timings
- Corrected source change event to fire if and only if size actually changes
- Locked open and release

Changes since v2:
- Switch to streaming interface. This involved a lot of changes.
- Rework memory allocation due to using videobuf2 buffers, but also only allocate the necessary size of source buffer rather than the max size

Changes since v1:
- Removed le32_to_cpu calls for JPEG header data
- Reworked v4l2 ioctls to be compliant.
- Added JPEG controls
- Updated devicetree docs according to Rob's suggestions.
- Added myself to MAINTAINERS

Eddie James (2):
dt-bindings: media: Add Aspeed Video Engine binding documentation
media: platform: Add Aspeed Video Engine driver

 .../devicetree/bindings/media/aspeed-video.txt     |   26 +
 MAINTAINERS                                        |    8 +
 drivers/media/platform/Kconfig                     |    9 +
 drivers/media/platform/Makefile                    |    1 +
 drivers/media/platform/aspeed-video.c              | 1711 ++++++++++++++++++++
 5 files changed, 1755 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/aspeed-video.txt
 create mode 100644 drivers/media/platform/aspeed-video.c
#7 lore raw
In reply to Hans Verkuil
Quoted 18 lines · Hans Verkuil
Quoted 10 lines · Eddie James

From: Eddie James <[email protected]>

The Video Engine (VE) embedded in the Aspeed AST2400 and AST2500 SOCs can capture and compress video data from digital or analog sources. With the Aspeed chip acting as a service processor, the Video Engine can capture the host processor graphics output.

This series adds a V4L2 driver for the VE, providing the usual V4L2 streaming interface by way of videobuf2. Each frame, the driver triggers the hardware to capture the host graphics output and compress it to JPEG format.

I reviewed the driver, and there is still confusion about active timings and detected timings. You are really close, but it is still not right.

The timings returned by G_DV_TIMINGS should never change, unless by calling S_DV_TIMINGS. The format returned by G_FMT should never change, unless by calling S_DV_TIMINGS (which implicitly changes the format) or S_FMT.

Quoted 5 lines

Timings changes from the video or calling QUERY_DV_TIMINGS should have NO effect on the timings/format returned by G_DV_TIMINGS/G_FMT.

Obviously, if the video timings change, then streaming will halt and an event is issued so userspace can take action.

Thanks, I have made some changes for v6.

Quoted 59 lines
Quoted 4 lines

v4l-utils HEAD dd3ff81f58c4e1e6f33765dc61ad33c48ae6bb07

v4l2-compliance SHA: not available, 32 bits

<snip>

Quoted 6 lines

Control ioctls (Input 0):
test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
test VIDIOC_QUERYCTRL: OK
test VIDIOC_G/S_CTRL: OK
test VIDIOC_G/S/TRY_EXT_CTRLS: OK
fail: v4l2-test-controls.cpp(823): failed to find event for control 'Chroma Subsampling'

That's weird. It's not clear to me why this fails.

Quoted 16 lines

test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) Standard Controls: 3 Private Controls: 0

Format ioctls (Input 0):
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK test VIDIOC_G/S_PARM: OK
test VIDIOC_G_FBUF: OK (Not Supported) test VIDIOC_G_FMT: OK
test VIDIOC_TRY_FMT: OK
test VIDIOC_S_FMT: OK
test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) test Cropping: OK (Not Supported)
test Composing: OK (Not Supported)
test Scaling: OK (Not Supported)

Quoted 7 lines

Codec ioctls (Input 0):
test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) test VIDIOC_G_ENC_INDEX: OK (Not Supported) test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)

Buffer ioctls (Input 0):

		fail: v4l2-test-buffers.cpp(422): dmabuf_valid ^ !!(caps & V4L2_BUF_CAP_SUPPORTS_DMABUF)

I updated v4l2-compliance, as this test was a bit too strict.

Quoted 5 lines

test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: FAIL test VIDIOC_EXPBUF: OK (Not Supported)

Test input 0:

Quoted 7 lines

Streaming ioctls:
test read/write: OK
test blocking wait: OK
test MMAP: OK
test USERPTR: OK (Not Supported)
fail: v4l2-test-buffers.cpp(1102): exp_q.reqbufs(expbuf_node, q.g_buffers())
fail: v4l2-test-buffers.cpp(1192): setupDmaBuf(expbuf_node, node, q, exp_q)

You need to add:

.vidioc_expbuf = vb2_ioctl_expbuf,

to aspeed_video_ioctl_ops.

Quoted 2 lines

test DMABUF: FAIL

Quoted 7 lines
Quoted 5 lines

Total: 48, Succeeded: 45, Failed: 3, Warnings: 0

The apparent rate of change to the v4l2/vb2 API makes it difficult to pass these tests. None of the failing tests even ran last time I submitted my series. And V4L2_BUF_CAP_SUPPORTS_DMABUF is undefined in 4.19.

When developing new drivers you should use the master branch of
https://git.linuxtv.org/media_tree.git/

Our 4.18 tree has quite a few chip-specific patches that I need that are not upstreamed yet, so it's not possible for me to use that.

Thanks,
Eddie

Quoted 53 lines

The v4l-utils repo is kept in sync with the latest code from that master branch.

Regards,

Hans

Quoted 46 lines

Changes since v4:
- Set real min and max resolution in enum_dv_timings
- Add check for vb2_is_busy before settings the timings
- Set max frame rate to the actual max rather than max + 1
- Correct the input status to 0.
- Rework resolution change to only set the relevant h/w regs during startup or when set_timings is called.

Changes since v3:
- Switch update reg function to use u32 clear rather than unsigned long mask
- Add timing information from host VGA signal
- Fix binding documentation mispelling
- Fix upper case hex values
- Add wait_prepare and wait_finish
- Set buffer state to queued (rather than error) if streaming fails to start
- Switch engine busy print statement to error
- Removed a couple unecessary type assignments in v4l2 ioctls
- Added query_dv_timings, fixed get_dv_timings
- Corrected source change event to fire if and only if size actually changes
- Locked open and release

Changes since v2:
- Switch to streaming interface. This involved a lot of changes.
- Rework memory allocation due to using videobuf2 buffers, but also only allocate the necessary size of source buffer rather than the max size

Changes since v1:
- Removed le32_to_cpu calls for JPEG header data
- Reworked v4l2 ioctls to be compliant.
- Added JPEG controls
- Updated devicetree docs according to Rob's suggestions.
- Added myself to MAINTAINERS

Eddie James (2):
dt-bindings: media: Add Aspeed Video Engine binding documentation
media: platform: Add Aspeed Video Engine driver

  .../devicetree/bindings/media/aspeed-video.txt     |   26 +
  MAINTAINERS                                        |    8 +
  drivers/media/platform/Kconfig                     |    9 +
  drivers/media/platform/Makefile                    |    1 +
  drivers/media/platform/aspeed-video.c              | 1711 ++++++++++++++++++++
  5 files changed, 1755 insertions(+)

create mode 100644 Documentation/devicetree/bindings/media/aspeed-video.txt create mode 100644 drivers/media/platform/aspeed-video.c