add uart DMA function
Subsystems (5)
v9 cover add uart DMA function
In Mediatek SOCs, the uart can support DMA function.
Base on DMA engine formwork, we add the DMA code to support uart. And put the code under drivers/dma.
This series contains document bindings, Kconfig to control the function enable or not, device tree including interrupt and dma device node, the code of UART DMA
Changes compared to v8
-revise missing items
Changes compared to v7:
-modify apdma uart tx
Changes compared to v6:
-Correct spelling
Changes compared to v5:
-move 'requst irqs' to alloc channel
-remove tasklet.
Changes compared to v4:
-modify Kconfig depends on.
Changes compared to v3:
-fix CONFIG_PM, will cause build fail
Changes compared to v2:
-remove unimportant parameters
-instead of cookie, use APIs of virtual channel.
-use of_dma_xlate_by_chan_id.
Changes compared to v1:
-mian revised file, 8250_mtk_dma.c
--parameters renamed for standard
--remove atomic operation
PATCH v9 1/2 dmaengine: 8250_mtk_dma: add MediaTek uart DMA support
In DMA engine framework, add 8250 uart dma to support MediaTek uart. If MediaTek uart enabled(SERIAL_8250_MT6577), and want to improve the performance, can enable the function.
--- drivers/dma/mediatek/8250_mtk_dma.c | 652 +++++++++++++++++++++++++++++++++++ drivers/dma/mediatek/Kconfig | 11 + drivers/dma/mediatek/Makefile | 1 + 3 files changed, 664 insertions(+) create mode 100644 drivers/dma/mediatek/8250_mtk_dma.c
drivers/dma/mediatek/8250_mtk_dma.c new file +652 -0
@@ -0,0 +1,652 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* MediaTek 8250 DMA driver. +* +* Copyright (c) 2018 MediaTek Inc. +* Author: Long Cheng <[email protected]> +*/ + +#include <linux/clk.h> +#include <linux/dmaengine.h> +#include <linux/dma-mapping.h> +#include <linux/err.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/iopoll.h> +#include <linux/kernel.h> +#include <linux/list.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/of_dma.h> +#include <linux/platform_device.h> +#include <linux/pm_runtime.h> +#include <linux/slab.h> +#include <linux/spinlock.h> + +#include "../virt-dma.h" + +#define MTK_UART_APDMA_CHANNELS (CONFIG_SERIAL_8250_NR_UARTS * 2) + +#define VFF_EN_B BIT(0) +#define VFF_STOP_B BIT(0) +#define VFF_FLUSH_B BIT(0) +#define VFF_4G_SUPPORT_B BIT(0) +#define VFF_RX_INT_EN0_B BIT(0)/*rx valid size >= vff thre*/ +#define VFF_RX_INT_EN1_B BIT(1) +#define VFF_TX_INT_EN_B BIT(0)/*tx left size >= vff thre*/ +#define VFF_WARM_RST_B BIT(0) +#define VFF_RX_INT_FLAG_CLR_B (BIT(0) | BIT(1)) +#define VFF_TX_INT_FLAG_CLR_B 0 +#define VFF_STOP_CLR_B 0 +#define VFF_INT_EN_CLR_B 0 +#define VFF_4G_SUPPORT_CLR_B 0 + +/* interrupt trigger level for tx */ +#define VFF_TX_THRE (n) ((n) * 7 / 8) +/* interrupt trigger level for rx */ +#define VFF_RX_THRE (n) ((n) * 3 / 4) + +#define VFF_RING_SIZE 0xffffU +/* invert this bit when wrap ring head again*/ +#define VFF_RING_WRAP 0x10000U + +#define VFF_INT_FLAG 0x00 +#define VFF_INT_EN 0x04 +#define VFF_EN 0x08 +#define VFF_RST 0x0c +#define VFF_STOP 0x10 +#define VFF_FLUSH 0x14 +#define VFF_ADDR 0x1c +#define VFF_LEN 0x24 +#define VFF_THRE 0x28 +#define VFF_WPT 0x2c +#define VFF_RPT 0x30 +/*TX: the buffer size HW can read. RX: the buffer size SW can read.*/ +#define VFF_VALID_SIZE 0x3c +/*TX: the buffer size SW can write. RX: the buffer size HW can write.*/ +#define VFF_LEFT_SIZE 0x40 +#define VFF_DEBUG_STATUS 0x50 +#define VFF_4G_SUPPORT 0x54 + +struct mtk_uart_apdmadev { +struct dma_device ddev; +struct clk *clk; +bool support_33bits; +unsigned int dma_irq[MTK_UART_APDMA_CHANNELS ]; +}; + +struct mtk_uart_apdma_desc { +struct virt_dma_desc vd; + +unsigned int avail_len; +}; + +struct mtk_chan { +struct virt_dma_chan vc; +struct dma_slave_config cfg; +void __iomem *base; +struct mtk_uart_apdma_desc *desc; + +bool requested; + +unsigned int rx_status; +}; + +static inline struct mtk_uart_apdmadev * +to_mtk_uart_apdma_dev (struct dma_device *d) +{ + return container_of(d, struct mtk_uart_apdmadev, ddev); +} + +static inline struct mtk_chan *to_mtk_uart_apdma_chan (struct dma_chan *c) +{ + return container_of(c, struct mtk_chan, vc.chan); +} + +static inline struct mtk_uart_apdma_desc *to_mtk_uart_apdma_desc + (struct dma_async_tx_descriptor *t) +{ + return container_of(t, struct mtk_uart_apdma_desc, vd.tx); +} + +static void mtk_uart_apdma_write (struct mtk_chan *c, +unsigned int reg,unsigned int val) +{ +writel (val, c->base + reg); +} + +static unsigned int mtk_uart_apdma_read (struct mtk_chan *c,unsigned int reg) +{ +return readl (c->base + reg); +} + +static void mtk_uart_apdma_desc_free (struct virt_dma_desc *vd) +{ +struct dma_chan *chan = vd->tx.chan; +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); + +kfree (c->desc); +} + +static void mtk_uart_apdma_start_tx (struct mtk_chan *c) +{ +unsigned int len, send, left, wpt, d_wpt, tmp; +int ret; + + left =mtk_uart_apdma_read (c,VFF_LEFT_SIZE ); +if (!left) { +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_TX_INT_EN_B ); +return ; + } + +/* Wait 1sec for flush, can't sleep*/ + ret =readx_poll_timeout (readl, c->base +VFF_FLUSH , tmp, + tmp !=VFF_FLUSH_B ,0 ,1000000 ); +if (ret) +dev_warn (c->vc.chan.device->dev,"tx: fail, debug=0x%x\n" , +mtk_uart_apdma_read (c,VFF_DEBUG_STATUS )); + + send = min_t(unsigned int, left, c->desc->avail_len); + wpt =mtk_uart_apdma_read (c,VFF_WPT ); + len =mtk_uart_apdma_read (c,VFF_LEN ); + + d_wpt = wpt + send; +if ((d_wpt &VFF_RING_SIZE ) >= len) { + d_wpt = d_wpt - len; + d_wpt = d_wpt ^VFF_RING_WRAP ; + } +mtk_uart_apdma_write (c,VFF_WPT , d_wpt); + + c->desc->avail_len -= send; + +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_TX_INT_EN_B ); +if (mtk_uart_apdma_read (c,VFF_FLUSH ) ==0U ) +mtk_uart_apdma_write (c,VFF_FLUSH ,VFF_FLUSH_B ); +} + +static void mtk_uart_apdma_start_rx (struct mtk_chan *c) +{ +struct mtk_uart_apdma_desc *d = c->desc; +unsigned int len, wg, rg, cnt; + +if ((mtk_uart_apdma_read (c,VFF_VALID_SIZE ) ==0U ) || + !d || !vchan_next_desc (&c->vc)) +return ; + + len =mtk_uart_apdma_read (c,VFF_LEN ); + rg =mtk_uart_apdma_read (c,VFF_RPT ); + wg =mtk_uart_apdma_read (c,VFF_WPT ); +if ((rg ^ wg) &VFF_RING_WRAP ) + cnt = (wg &VFF_RING_SIZE ) + len - (rg &VFF_RING_SIZE ); +else + cnt = (wg &VFF_RING_SIZE ) - (rg &VFF_RING_SIZE ); + + c->rx_status = cnt; +mtk_uart_apdma_write (c,VFF_RPT , wg); + +list_del (&d->vd.node); +vchan_cookie_complete (&d->vd); +} + +static irqreturn_t mtk_uart_apdma_irq_handler (int irq,void *dev_id) +{ +struct dma_chan *chan = (struct dma_chan *)dev_id; +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +struct mtk_uart_apdma_desc *d; +unsigned long flags; + +spin_lock_irqsave (&c->vc.lock, flags); +if (c->cfg.direction ==DMA_DEV_TO_MEM ) { +mtk_uart_apdma_write (c,VFF_INT_FLAG ,VFF_RX_INT_FLAG_CLR_B ); +mtk_uart_apdma_start_rx (c); + }else if (c->cfg.direction ==DMA_MEM_TO_DEV ) { + d = c->desc; + +mtk_uart_apdma_write (c,VFF_INT_FLAG ,VFF_TX_INT_FLAG_CLR_B ); + +if (d->avail_len !=0U ) { +mtk_uart_apdma_start_tx (c); + }else { +list_del (&d->vd.node); +vchan_cookie_complete (&d->vd); + } + } +spin_unlock_irqrestore (&c->vc.lock, flags); + +return IRQ_HANDLED ; +} + +static int mtk_uart_apdma_alloc_chan_resources (struct dma_chan *chan) +{ +struct mtk_uart_apdmadev *mtkd =to_mtk_uart_apdma_dev (chan->device); +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +u32 tmp; +int ret; + +pm_runtime_get_sync (mtkd->ddev.dev); + +mtk_uart_apdma_write (c,VFF_ADDR ,0 ); +mtk_uart_apdma_write (c,VFF_THRE ,0 ); +mtk_uart_apdma_write (c,VFF_LEN ,0 ); +mtk_uart_apdma_write (c,VFF_RST ,VFF_WARM_RST_B ); + + ret =readx_poll_timeout (readl, c->base +VFF_EN , tmp, + tmp ==0 ,10 ,100 ); +if (ret) { +dev_err (chan->device->dev,"dma reset: fail, timeout\n" ); +return ret; + } + +if (!c->requested) { + c->requested = true; + ret =request_irq (mtkd->dma_irq[chan->chan_id], + mtk_uart_apdma_irq_handler,IRQF_TRIGGER_NONE , +KBUILD_MODNAME , chan); +if (ret <0 ) { +dev_err (chan->device->dev,"Can't request dma IRQ\n" ); +return -EINVAL ; + } + } + +if (mtkd->support_33bits) +mtk_uart_apdma_write (c,VFF_4G_SUPPORT ,VFF_4G_SUPPORT_CLR_B ); + +return ret; +} + +static void mtk_uart_apdma_free_chan_resources (struct dma_chan *chan) +{ +struct mtk_uart_apdmadev *mtkd =to_mtk_uart_apdma_dev (chan->device); +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); + +if (c->requested) { + c->requested = false; +free_irq (mtkd->dma_irq[chan->chan_id], chan); + } + +tasklet_kill (&c->vc.task); + +vchan_free_chan_resources (&c->vc); + +pm_runtime_put_sync (mtkd->ddev.dev); +} + +static enum dma_status mtk_uart_apdma_tx_status (struct dma_chan *chan, +dma_cookie_t cookie, +struct dma_tx_state *txstate) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +enum dma_status ret; +unsigned long flags; + +if (!txstate) +return DMA_ERROR ; + + ret =dma_cookie_status (chan, cookie, txstate); +spin_lock_irqsave (&c->vc.lock, flags); +if (ret ==DMA_IN_PROGRESS ) { + c->rx_status =mtk_uart_apdma_read (c,VFF_RPT ) &VFF_RING_SIZE ; +dma_set_residue (txstate, c->rx_status); + }else if (ret ==DMA_COMPLETE && c->cfg.direction ==DMA_DEV_TO_MEM ) { +dma_set_residue (txstate, c->rx_status); + }else { +dma_set_residue (txstate,0 ); + } +spin_unlock_irqrestore (&c->vc.lock, flags); + +return ret; +} + +/* +* dmaengine_prep_slave_single will call the function. and sglen is 1. +* 8250 uart using one ring buffer, and deal with one sg. +*/ +static struct dma_async_tx_descriptor *mtk_uart_apdma_prep_slave_sg + (struct dma_chan *chan,struct scatterlist *sgl, +unsigned int sglen,enum dma_transfer_direction dir, +unsigned long tx_flags,void *context) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +struct mtk_uart_apdma_desc *d; + +if ((dir !=DMA_DEV_TO_MEM ) && + (dir !=DMA_MEM_TO_DEV )) { +dev_err (chan->device->dev,"bad direction\n" ); +return NULL ; + } + +/* Now allocate and setup the descriptor */ + d =kzalloc (sizeof (*d),GFP_ATOMIC ); +if (!d) +return NULL ; + +/* sglen is 1 */ + d->avail_len =sg_dma_len (sgl); + +return vchan_tx_prep (&c->vc, &d->vd, tx_flags); +} + +static void mtk_uart_apdma_issue_pending (struct dma_chan *chan) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +struct virt_dma_desc *vd; +unsigned long flags; + +spin_lock_irqsave (&c->vc.lock, flags); +if (c->cfg.direction ==DMA_DEV_TO_MEM ) { +if (vchan_issue_pending (&c->vc)) { + vd =vchan_next_desc (&c->vc); + c->desc =to_mtk_uart_apdma_desc (&vd->tx); +mtk_uart_apdma_start_rx (c); + } + }else if (c->cfg.direction ==DMA_MEM_TO_DEV ) { +if (vchan_issue_pending (&c->vc)) { + vd =vchan_next_desc (&c->vc); + c->desc =to_mtk_uart_apdma_desc (&vd->tx); +mtk_uart_apdma_start_tx (c); + } + } +spin_unlock_irqrestore (&c->vc.lock, flags); +} + +static int mtk_uart_apdma_slave_config (struct dma_chan *chan, +struct dma_slave_config *cfg) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +struct mtk_uart_apdmadev *mtkd = +to_mtk_uart_apdma_dev (c->vc.chan.device); + + c->cfg = *cfg; + +if (cfg->direction ==DMA_DEV_TO_MEM ) { +unsigned int rx_len = cfg->src_addr_width *1024 ; + +mtk_uart_apdma_write (c,VFF_ADDR , cfg->src_addr); +mtk_uart_apdma_write (c,VFF_LEN , rx_len); +mtk_uart_apdma_write (c,VFF_THRE ,VFF_RX_THRE (rx_len)); +mtk_uart_apdma_write (c,VFF_INT_EN , +VFF_RX_INT_EN0_B |VFF_RX_INT_EN1_B ); +mtk_uart_apdma_write (c,VFF_RPT ,0 ); +mtk_uart_apdma_write (c,VFF_INT_FLAG ,VFF_RX_INT_FLAG_CLR_B ); +mtk_uart_apdma_write (c,VFF_EN ,VFF_EN_B ); + }else if (cfg->direction ==DMA_MEM_TO_DEV ) { +unsigned int tx_len = cfg->dst_addr_width *1024 ; + +mtk_uart_apdma_write (c,VFF_ADDR , cfg->dst_addr); +mtk_uart_apdma_write (c,VFF_LEN , tx_len); +mtk_uart_apdma_write (c,VFF_THRE ,VFF_TX_THRE (tx_len)); +mtk_uart_apdma_write (c,VFF_WPT ,0 ); +mtk_uart_apdma_write (c,VFF_INT_FLAG ,VFF_TX_INT_FLAG_CLR_B ); +mtk_uart_apdma_write (c,VFF_EN ,VFF_EN_B ); + } + +if (mtkd->support_33bits) +mtk_uart_apdma_write (c,VFF_4G_SUPPORT ,VFF_4G_SUPPORT_B ); + +if (mtk_uart_apdma_read (c,VFF_EN ) !=VFF_EN_B ) { +dev_err (chan->device->dev,"dir[%d] fail\n" , cfg->direction); +return -EINVAL ; + } + +return 0 ; +} + +static int mtk_uart_apdma_terminate_all (struct dma_chan *chan) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +unsigned long flags; +u32 tmp; +int ret; + +spin_lock_irqsave (&c->vc.lock, flags); + +mtk_uart_apdma_write (c,VFF_FLUSH ,VFF_FLUSH_B ); +/* Wait 1sec for flush, can't sleep*/ + ret =readx_poll_timeout (readl, c->base +VFF_FLUSH , tmp, + tmp !=VFF_FLUSH_B ,0 ,1000000 ); +if (ret) +dev_err (c->vc.chan.device->dev,"flush: fail, debug=0x%x\n" , +mtk_uart_apdma_read (c,VFF_DEBUG_STATUS )); + +/*set stop as 1 -> wait until en is 0 -> set stop as 0*/ +mtk_uart_apdma_write (c,VFF_STOP ,VFF_STOP_B ); + ret =readx_poll_timeout (readl, c->base +VFF_EN , tmp, + tmp ==0 ,10 ,100 ); +if (ret) +dev_err (c->vc.chan.device->dev,"stop: fail, debug=0x%x\n" , +mtk_uart_apdma_read (c,VFF_DEBUG_STATUS )); + +mtk_uart_apdma_write (c,VFF_STOP ,VFF_STOP_CLR_B ); +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_INT_EN_CLR_B ); + +if (c->cfg.direction ==DMA_DEV_TO_MEM ) +mtk_uart_apdma_write (c,VFF_INT_FLAG ,VFF_RX_INT_FLAG_CLR_B ); +else if (c->cfg.direction ==DMA_MEM_TO_DEV ) +mtk_uart_apdma_write (c,VFF_INT_FLAG ,VFF_TX_INT_FLAG_CLR_B ); + +spin_unlock_irqrestore (&c->vc.lock, flags); + +return 0 ; +} + +static int mtk_uart_apdma_device_pause (struct dma_chan *chan) +{ +/* just for check caps pass */ +return 0 ; +} + +static int mtk_uart_apdma_device_resume (struct dma_chan *chan) +{ +/* just for check caps pass */ +return 0 ; +} + +static void mtk_uart_apdma_free (struct mtk_uart_apdmadev *mtkd) +{ +while (list_empty (&mtkd->ddev.channels) ==0 ) { +struct mtk_chan *c =list_first_entry (&mtkd->ddev.channels, + struct mtk_chan, vc.chan.device_node); + +list_del (&c->vc.chan.device_node); +tasklet_kill (&c->vc.task); + } +} + +static const struct of_device_id mtk_uart_apdma_match[] = { + { .compatible ="mediatek,mt6577-uart-dma" , }, + {/* sentinel */ }, +}; +MODULE_DEVICE_TABLE (of, mtk_uart_apdma_match); + +static int mtk_uart_apdma_probe (struct platform_device *pdev) +{ +struct mtk_uart_apdmadev *mtkd; +struct resource *res; +struct mtk_chan *c; +unsigned int i; +int rc; + + mtkd =devm_kzalloc (&pdev->dev,sizeof (*mtkd),GFP_KERNEL ); +if (!mtkd) +return -ENOMEM ; + + mtkd->clk =devm_clk_get (&pdev->dev,NULL ); +if (IS_ERR (mtkd->clk)) { +dev_err (&pdev->dev,"No clock specified\n" ); + rc =PTR_ERR (mtkd->clk); +return rc; + } + +if (of_property_read_bool (pdev->dev.of_node,"dma-33bits" )) + mtkd->support_33bits = true; + + rc =dma_set_mask_and_coherent (&pdev->dev, +DMA_BIT_MASK (32 | mtkd->support_33bits)); +if (rc) +return rc; + +dma_cap_set (DMA_SLAVE , mtkd->ddev.cap_mask); + mtkd->ddev.device_alloc_chan_resources = + mtk_uart_apdma_alloc_chan_resources; + mtkd->ddev.device_free_chan_resources = + mtk_uart_apdma_free_chan_resources; + mtkd->ddev.device_tx_status = mtk_uart_apdma_tx_status; + mtkd->ddev.device_issue_pending = mtk_uart_apdma_issue_pending; + mtkd->ddev.device_prep_slave_sg = mtk_uart_apdma_prep_slave_sg; + mtkd->ddev.device_config = mtk_uart_apdma_slave_config; + mtkd->ddev.device_pause = mtk_uart_apdma_device_pause; + mtkd->ddev.device_resume = mtk_uart_apdma_device_resume; + mtkd->ddev.device_terminate_all = mtk_uart_apdma_terminate_all; + mtkd->ddev.src_addr_widths =BIT (DMA_SLAVE_BUSWIDTH_1_BYTE ); + mtkd->ddev.dst_addr_widths =BIT (DMA_SLAVE_BUSWIDTH_1_BYTE ); + mtkd->ddev.directions =BIT (DMA_DEV_TO_MEM ) |BIT (DMA_MEM_TO_DEV ); + mtkd->ddev.residue_granularity =DMA_RESIDUE_GRANULARITY_SEGMENT ; + mtkd->ddev.dev = &pdev->dev; +INIT_LIST_HEAD (&mtkd->ddev.channels); + +for (i =0 ; i <MTK_UART_APDMA_CHANNELS ; i++) { + c =devm_kzalloc (mtkd->ddev.dev,sizeof (*c),GFP_KERNEL ); +if (!c) { + rc = -ENODEV ; + goto err_no_dma; + } + + res =platform_get_resource (pdev,IORESOURCE_MEM , i); +if (!res) { + rc = -ENODEV ; + goto err_no_dma; + } + + c->base =devm_ioremap_resource (&pdev->dev, res); +if (IS_ERR (c->base)) { + rc =PTR_ERR (c->base); + goto err_no_dma; + } + c->requested = false; + c->vc.desc_free = mtk_uart_apdma_desc_free; +vchan_init (&c->vc, &mtkd->ddev); + + mtkd->dma_irq[i] =platform_get_irq (pdev, i); +if ((int )mtkd->dma_irq[i] <0 ) { +dev_err (&pdev->dev,"failed to get IRQ[%d]\n" , i); + rc = -EINVAL ; + goto err_no_dma; + } + } + +pm_runtime_enable (&pdev->dev); +pm_runtime_set_active (&pdev->dev); + + rc =dma_async_device_register (&mtkd->ddev); +if (rc) + goto rpm_disable; + +platform_set_drvdata (pdev, mtkd); + +if (pdev->dev.of_node) { +/* Device-tree DMA controller registration */ + rc =of_dma_controller_register (pdev->dev.of_node, + of_dma_xlate_by_chan_id, + mtkd); +if (rc) + goto dma_remove; + } + +return rc; + +dma_remove: +dma_async_device_unregister (&mtkd->ddev); +rpm_disable: +pm_runtime_disable (&pdev->dev); +err_no_dma: +mtk_uart_apdma_free (mtkd); +return rc; +} + +static int mtk_uart_apdma_remove (struct platform_device *pdev) +{ +struct mtk_uart_apdmadev *mtkd =platform_get_drvdata (pdev); + +if (pdev->dev.of_node) +of_dma_controller_free (pdev->dev.of_node); + +pm_runtime_disable (&pdev->dev); +pm_runtime_put_noidle (&pdev->dev); + +dma_async_device_unregister (&mtkd->ddev); +mtk_uart_apdma_free (mtkd); + +return 0 ; +} + +#ifdef CONFIG_PM_SLEEP +static int mtk_uart_apdma_suspend (struct device *dev) +{ +struct mtk_uart_apdmadev *mtkd =dev_get_drvdata (dev); + +if (!pm_runtime_suspended (dev)) +clk_disable_unprepare (mtkd->clk); + +return 0 ; +} + +static int mtk_uart_apdma_resume (struct device *dev) +{ +int ret; +struct mtk_uart_apdmadev *mtkd =dev_get_drvdata (dev); + +if (!pm_runtime_suspended (dev)) { + ret =clk_prepare_enable (mtkd->clk); +if (ret) +return ret; + } + +return 0 ; +} +#endif /* CONFIG_PM_SLEEP */ + +#ifdef CONFIG_PM +static int mtk_uart_apdma_runtime_suspend (struct device *dev) +{ +struct mtk_uart_apdmadev *mtkd =dev_get_drvdata (dev); + +clk_disable_unprepare (mtkd->clk); + +return 0 ; +} + +static int mtk_uart_apdma_runtime_resume (struct device *dev) +{ +int ret; +struct mtk_uart_apdmadev *mtkd =dev_get_drvdata (dev); + + ret =clk_prepare_enable (mtkd->clk); +if (ret) +return ret; + +return 0 ; +} +#endif /* CONFIG_PM */ + +static const struct dev_pm_ops mtk_uart_apdma_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(mtk_uart_apdma_suspend, mtk_uart_apdma_resume) +SET_RUNTIME_PM_OPS (mtk_uart_apdma_runtime_suspend, + mtk_uart_apdma_runtime_resume,NULL ) +}; + +static struct platform_driver mtk_uart_apdma_driver = { + .probe = mtk_uart_apdma_probe, + .remove = mtk_uart_apdma_remove, + .driver = { + .name =KBUILD_MODNAME , + .pm = &mtk_uart_apdma_pm_ops, + .of_match_table =of_match_ptr (mtk_uart_apdma_match), + }, +}; + +module_platform_driver (mtk_uart_apdma_driver); + +MODULE_DESCRIPTION ("MediaTek UART APDMA Controller Driver" ); +MODULE_AUTHOR ("Long Cheng <[email protected]>" ); +MODULE_LICENSE ("GPL v2" ); +
drivers/dma/mediatek/Kconfig +11 -0
@@ -1,4 +1,15 @@ +config DMA_MTK_UART + tristate "MediaTek SoCs APDMA support for UART" + depends on OF && SERIAL_8250_MT6577 + select DMA_ENGINE + select DMA_VIRTUAL_CHANNELS + help + Support for the UART DMA engine found on MediaTek MTK SoCs. + when SERIAL_8250_MT6577 is enabled, and if you want to use DMA, + you can enable the config. the DMA engine can only be used + with MediaTek SoCs. + config MTK_HSDMA tristate "MediaTek High-Speed DMA controller support" depends on ARCH_MEDIATEK || COMPILE_TEST
drivers/dma/mediatek/Makefile +1 -0
@@ -1 +1,2 @@ +obj-$(CONFIG_DMA_MTK_UART) += 8250_mtk_dma.o obj-$(CONFIG_MTK_HSDMA) += mtk-hsdma.o
Re: [PATCH v9 1/2] dmaengine: 8250_mtk_dma: add MediaTek uart DMA support
Quoted 58 lines · Long Cheng
In DMA engine framework, add 8250 uart dma to support MediaTek uart. If MediaTek uart
enabled(SERIAL_8250_MT6577), and want to improve the performance, can enable the function.Signed-off-by Long Cheng <[email protected]>--- drivers/dma/mediatek/8250_mtk_dma.c | 652 +++++++++++++++++++++++++++++++++++ drivers/dma/mediatek/Kconfig | 11 + drivers/dma/mediatek/Makefile | 1 + 3 files changed, 664 insertions(+) create mode 100644 drivers/dma/mediatek/8250_mtk_dma.cdrivers/dma/mediatek/8250_mtk_dma.c new file +39
-0@@ -0,0 +1,652 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* MediaTek 8250 DMA driver. +* +* Copyright (c) 2018 MediaTek Inc. +* Author: Long Cheng <[email protected]> +*/ + +#include <linux/clk.h> +#include <linux/dmaengine.h> +#include <linux/dma-mapping.h> +#include <linux/err.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/iopoll.h> +#include <linux/kernel.h> +#include <linux/list.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/of_dma.h> +#include <linux/platform_device.h> +#include <linux/pm_runtime.h> +#include <linux/slab.h> +#include <linux/spinlock.h> + +#include "../virt-dma.h" + +#define MTK_UART_APDMA_CHANNELS (CONFIG_SERIAL_8250_NR_UARTS * 2) + +#define VFF_EN_B BIT(0) +#define VFF_STOP_B BIT(0) +#define VFF_FLUSH_B BIT(0) +#define VFF_4G_SUPPORT_B BIT(0) +#define VFF_RX_INT_EN0_B BIT(0)/*rx valid size >= vff thre*/ +#define VFF_RX_INT_EN1_B BIT(1) +#define VFF_TX_INT_EN_B BIT(0)/*tx left size >= vff thre*/ +#define VFF_WARM_RST_B BIT(0) +#define VFF_RX_INT_FLAG_CLR_B (BIT(0) | BIT(1)) +#define VFF_TX_INT_FLAG_CLR_B 0
drivers/dma/mediatek/8250_mtk_dma.c line 49
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+#define VFF_STOP_CLR_B 0 +#define VFF_INT_EN_CLR_B 0 +#define VFF_4G_SUPPORT_CLR_B 0 + +/* interrupt trigger level for tx */ +#define VFF_TX_THRE (n) ((n) * 7 / 8) +/* interrupt trigger level for rx */ +#define VFF_RX_THRE (n) ((n) * 3 / 4) + +#define VFF_RING_SIZE 0xffffU
Well, the size is actually 0x10000. Maybe call this VFF_RING_SIZE_MASK?
Quoted 5 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +5
-0+/* invert this bit when wrap ring head again*/ +#define VFF_RING_WRAP 0x10000U + +#define VFF_INT_FLAG 0x00 +#define VFF_INT_EN 0x04
drivers/dma/mediatek/8250_mtk_dma.c line 64
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+#define VFF_EN 0x08 +#define VFF_RST 0x0c +#define VFF_STOP 0x10 +#define VFF_FLUSH 0x14 +#define VFF_ADDR 0x1c +#define VFF_LEN 0x24 +#define VFF_THRE 0x28 +#define VFF_WPT 0x2c +#define VFF_RPT 0x30 +/*TX: the buffer size HW can read. RX: the buffer size SW can read.*/
nit: Spaces after /* and before */ (and a lot more occurences below, please fix them all).
Quoted 68 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +68
-0+#define VFF_VALID_SIZE 0x3c +/*TX: the buffer size SW can write. RX: the buffer size HW can write.*/ +#define VFF_LEFT_SIZE 0x40 +#define VFF_DEBUG_STATUS 0x50 +#define VFF_4G_SUPPORT 0x54 + +struct mtk_uart_apdmadev { +struct dma_device ddev; +struct clk *clk; +bool support_33bits; +unsigned int dma_irq[MTK_UART_APDMA_CHANNELS ]; +}; + +struct mtk_uart_apdma_desc { +struct virt_dma_desc vd; + +unsigned int avail_len; +}; + +struct mtk_chan { +struct virt_dma_chan vc; +struct dma_slave_config cfg; +void __iomem *base; +struct mtk_uart_apdma_desc *desc; + +bool requested; + +unsigned int rx_status; +}; + +static inline struct mtk_uart_apdmadev * +to_mtk_uart_apdma_dev (struct dma_device *d) +{ + return container_of(d, struct mtk_uart_apdmadev, ddev); +} + +static inline struct mtk_chan *to_mtk_uart_apdma_chan (struct dma_chan *c) +{ + return container_of(c, struct mtk_chan, vc.chan); +} + +static inline struct mtk_uart_apdma_desc *to_mtk_uart_apdma_desc + (struct dma_async_tx_descriptor *t) +{ + return container_of(t, struct mtk_uart_apdma_desc, vd.tx); +} + +static void mtk_uart_apdma_write (struct mtk_chan *c, +unsigned int reg,unsigned int val) +{ +writel (val, c->base + reg); +} + +static unsigned int mtk_uart_apdma_read (struct mtk_chan *c,unsigned int reg) +{ +return readl (c->base + reg); +} + +static void mtk_uart_apdma_desc_free (struct virt_dma_desc *vd) +{ +struct dma_chan *chan = vd->tx.chan; +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); + +kfree (c->desc); +} + +static void mtk_uart_apdma_start_tx (struct mtk_chan *c) +{
drivers/dma/mediatek/8250_mtk_dma.c line 142
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+unsigned int len, send, left, wpt, d_wpt, tmp; +int ret; + + left =mtk_uart_apdma_read (c,VFF_LEFT_SIZE ); +if (!left) { +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_TX_INT_EN_B ); +return ; + } + +/* Wait 1sec for flush, can't sleep*/
nit: one space after ',', period after 'sleep', space before '*'.
drivers/dma/mediatek/8250_mtk_dma.c line 147
Quoted 5 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +5
-0+ ret =readx_poll_timeout (readl, c->base +VFF_FLUSH , tmp, + tmp !=VFF_FLUSH_B ,0 ,1000000 ); +if (ret) +dev_warn (c->vc.chan.device->dev,"tx: fail, debug=0x%x\n" , +mtk_uart_apdma_read (c,VFF_DEBUG_STATUS ));
Why do we need to wait for flush now? The previous implementation did not require this...
drivers/dma/mediatek/8250_mtk_dma.c line 154
Quoted 7 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +7
-0+ + send = min_t(unsigned int, left, c->desc->avail_len); + wpt =mtk_uart_apdma_read (c,VFF_WPT ); + len =mtk_uart_apdma_read (c,VFF_LEN ); + + d_wpt = wpt + send; +if ((d_wpt &VFF_RING_SIZE ) >= len) {
I don't get why you need to add "& VFF_RING_SIZE". If wpt + send > VFF_RING_SIZE, don't you need to toggle VFF_RING_WRAP too?
drivers/dma/mediatek/8250_mtk_dma.c line 165
Quoted 11 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +11
-0+ d_wpt = d_wpt - len; + d_wpt = d_wpt ^VFF_RING_WRAP ; + } +mtk_uart_apdma_write (c,VFF_WPT , d_wpt); + + c->desc->avail_len -= send; + +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_TX_INT_EN_B ); +if (mtk_uart_apdma_read (c,VFF_FLUSH ) ==0U ) +mtk_uart_apdma_write (c,VFF_FLUSH ,VFF_FLUSH_B ); +}
(thanks for the rest of the changes, this looks much more readable)
Quoted 48 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +48
-0+ +static void mtk_uart_apdma_start_rx (struct mtk_chan *c) +{ +struct mtk_uart_apdma_desc *d = c->desc; +unsigned int len, wg, rg, cnt; + +if ((mtk_uart_apdma_read (c,VFF_VALID_SIZE ) ==0U ) || + !d || !vchan_next_desc (&c->vc)) +return ; + + len =mtk_uart_apdma_read (c,VFF_LEN ); + rg =mtk_uart_apdma_read (c,VFF_RPT ); + wg =mtk_uart_apdma_read (c,VFF_WPT ); +if ((rg ^ wg) &VFF_RING_WRAP ) + cnt = (wg &VFF_RING_SIZE ) + len - (rg &VFF_RING_SIZE ); +else + cnt = (wg &VFF_RING_SIZE ) - (rg &VFF_RING_SIZE ); + + c->rx_status = cnt; +mtk_uart_apdma_write (c,VFF_RPT , wg); + +list_del (&d->vd.node); +vchan_cookie_complete (&d->vd); +} + +static irqreturn_t mtk_uart_apdma_irq_handler (int irq,void *dev_id) +{ +struct dma_chan *chan = (struct dma_chan *)dev_id; +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +struct mtk_uart_apdma_desc *d; +unsigned long flags; + +spin_lock_irqsave (&c->vc.lock, flags); +if (c->cfg.direction ==DMA_DEV_TO_MEM ) { +mtk_uart_apdma_write (c,VFF_INT_FLAG ,VFF_RX_INT_FLAG_CLR_B ); +mtk_uart_apdma_start_rx (c); + }else if (c->cfg.direction ==DMA_MEM_TO_DEV ) { + d = c->desc; + +mtk_uart_apdma_write (c,VFF_INT_FLAG ,VFF_TX_INT_FLAG_CLR_B ); + +if (d->avail_len !=0U ) { +mtk_uart_apdma_start_tx (c); + }else { +list_del (&d->vd.node); +vchan_cookie_complete (&d->vd); + } + }
drivers/dma/mediatek/8250_mtk_dma.c line 223
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+spin_unlock_irqrestore (&c->vc.lock, flags); + +return IRQ_HANDLED ; +} + +static int mtk_uart_apdma_alloc_chan_resources (struct dma_chan *chan) +{ +struct mtk_uart_apdmadev *mtkd =to_mtk_uart_apdma_dev (chan->device); +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +u32 tmp;
In the rest of the code, you use unsigned int as type. I think u32 is a little bit better, but please be consistent.
Quoted 80 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +80
-0+int ret; + +pm_runtime_get_sync (mtkd->ddev.dev); + +mtk_uart_apdma_write (c,VFF_ADDR ,0 ); +mtk_uart_apdma_write (c,VFF_THRE ,0 ); +mtk_uart_apdma_write (c,VFF_LEN ,0 ); +mtk_uart_apdma_write (c,VFF_RST ,VFF_WARM_RST_B ); + + ret =readx_poll_timeout (readl, c->base +VFF_EN , tmp, + tmp ==0 ,10 ,100 ); +if (ret) { +dev_err (chan->device->dev,"dma reset: fail, timeout\n" ); +return ret; + } + +if (!c->requested) { + c->requested = true; + ret =request_irq (mtkd->dma_irq[chan->chan_id], + mtk_uart_apdma_irq_handler,IRQF_TRIGGER_NONE , +KBUILD_MODNAME , chan); +if (ret <0 ) { +dev_err (chan->device->dev,"Can't request dma IRQ\n" ); +return -EINVAL ; + } + } + +if (mtkd->support_33bits) +mtk_uart_apdma_write (c,VFF_4G_SUPPORT ,VFF_4G_SUPPORT_CLR_B ); + +return ret; +} + +static void mtk_uart_apdma_free_chan_resources (struct dma_chan *chan) +{ +struct mtk_uart_apdmadev *mtkd =to_mtk_uart_apdma_dev (chan->device); +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); + +if (c->requested) { + c->requested = false; +free_irq (mtkd->dma_irq[chan->chan_id], chan); + } + +tasklet_kill (&c->vc.task); + +vchan_free_chan_resources (&c->vc); + +pm_runtime_put_sync (mtkd->ddev.dev); +} + +static enum dma_status mtk_uart_apdma_tx_status (struct dma_chan *chan, +dma_cookie_t cookie, +struct dma_tx_state *txstate) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +enum dma_status ret; +unsigned long flags; + +if (!txstate) +return DMA_ERROR ; + + ret =dma_cookie_status (chan, cookie, txstate); +spin_lock_irqsave (&c->vc.lock, flags); +if (ret ==DMA_IN_PROGRESS ) { + c->rx_status =mtk_uart_apdma_read (c,VFF_RPT ) &VFF_RING_SIZE ; +dma_set_residue (txstate, c->rx_status); + }else if (ret ==DMA_COMPLETE && c->cfg.direction ==DMA_DEV_TO_MEM ) { +dma_set_residue (txstate, c->rx_status); + }else { +dma_set_residue (txstate,0 ); + } +spin_unlock_irqrestore (&c->vc.lock, flags); + +return ret; +} + +/* +* dmaengine_prep_slave_single will call the function. and sglen is 1. +* 8250 uart using one ring buffer, and deal with one sg. +*/
drivers/dma/mediatek/8250_mtk_dma.c line 313
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+static struct dma_async_tx_descriptor *mtk_uart_apdma_prep_slave_sg + (struct dma_chan *chan,struct scatterlist *sgl, +unsigned int sglen,enum dma_transfer_direction dir, +unsigned long tx_flags,void *context) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +struct mtk_uart_apdma_desc *d; + +if ((dir !=DMA_DEV_TO_MEM ) && + (dir !=DMA_MEM_TO_DEV )) {
This line fits in 80 chars.
Quoted 81 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +81
-0+dev_err (chan->device->dev,"bad direction\n" ); +return NULL ; + } + +/* Now allocate and setup the descriptor */ + d =kzalloc (sizeof (*d),GFP_ATOMIC ); +if (!d) +return NULL ; + +/* sglen is 1 */ + d->avail_len =sg_dma_len (sgl); + +return vchan_tx_prep (&c->vc, &d->vd, tx_flags); +} + +static void mtk_uart_apdma_issue_pending (struct dma_chan *chan) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +struct virt_dma_desc *vd; +unsigned long flags; + +spin_lock_irqsave (&c->vc.lock, flags); +if (c->cfg.direction ==DMA_DEV_TO_MEM ) { +if (vchan_issue_pending (&c->vc)) { + vd =vchan_next_desc (&c->vc); + c->desc =to_mtk_uart_apdma_desc (&vd->tx); +mtk_uart_apdma_start_rx (c); + } + }else if (c->cfg.direction ==DMA_MEM_TO_DEV ) { +if (vchan_issue_pending (&c->vc)) { + vd =vchan_next_desc (&c->vc); + c->desc =to_mtk_uart_apdma_desc (&vd->tx); +mtk_uart_apdma_start_tx (c); + } + } +spin_unlock_irqrestore (&c->vc.lock, flags); +} + +static int mtk_uart_apdma_slave_config (struct dma_chan *chan, +struct dma_slave_config *cfg) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +struct mtk_uart_apdmadev *mtkd = +to_mtk_uart_apdma_dev (c->vc.chan.device); + + c->cfg = *cfg; + +if (cfg->direction ==DMA_DEV_TO_MEM ) { +unsigned int rx_len = cfg->src_addr_width *1024 ; + +mtk_uart_apdma_write (c,VFF_ADDR , cfg->src_addr); +mtk_uart_apdma_write (c,VFF_LEN , rx_len); +mtk_uart_apdma_write (c,VFF_THRE ,VFF_RX_THRE (rx_len)); +mtk_uart_apdma_write (c,VFF_INT_EN , +VFF_RX_INT_EN0_B |VFF_RX_INT_EN1_B ); +mtk_uart_apdma_write (c,VFF_RPT ,0 ); +mtk_uart_apdma_write (c,VFF_INT_FLAG ,VFF_RX_INT_FLAG_CLR_B ); +mtk_uart_apdma_write (c,VFF_EN ,VFF_EN_B ); + }else if (cfg->direction ==DMA_MEM_TO_DEV ) { +unsigned int tx_len = cfg->dst_addr_width *1024 ; + +mtk_uart_apdma_write (c,VFF_ADDR , cfg->dst_addr); +mtk_uart_apdma_write (c,VFF_LEN , tx_len); +mtk_uart_apdma_write (c,VFF_THRE ,VFF_TX_THRE (tx_len)); +mtk_uart_apdma_write (c,VFF_WPT ,0 ); +mtk_uart_apdma_write (c,VFF_INT_FLAG ,VFF_TX_INT_FLAG_CLR_B ); +mtk_uart_apdma_write (c,VFF_EN ,VFF_EN_B ); + } + +if (mtkd->support_33bits) +mtk_uart_apdma_write (c,VFF_4G_SUPPORT ,VFF_4G_SUPPORT_B ); + +if (mtk_uart_apdma_read (c,VFF_EN ) !=VFF_EN_B ) { +dev_err (chan->device->dev,"dir[%d] fail\n" , cfg->direction); +return -EINVAL ; + } + +return 0 ; +} + +static int mtk_uart_apdma_terminate_all (struct dma_chan *chan)
drivers/dma/mediatek/8250_mtk_dma.c line 404
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +unsigned long flags; +u32 tmp; +int ret; + +spin_lock_irqsave (&c->vc.lock, flags); + +mtk_uart_apdma_write (c,VFF_FLUSH ,VFF_FLUSH_B ); +/* Wait 1sec for flush, can't sleep*/
ditto about comment format
Quoted 22 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +22
-0+ ret =readx_poll_timeout (readl, c->base +VFF_FLUSH , tmp, + tmp !=VFF_FLUSH_B ,0 ,1000000 ); +if (ret) +dev_err (c->vc.chan.device->dev,"flush: fail, debug=0x%x\n" , +mtk_uart_apdma_read (c,VFF_DEBUG_STATUS )); + +/*set stop as 1 -> wait until en is 0 -> set stop as 0*/ +mtk_uart_apdma_write (c,VFF_STOP ,VFF_STOP_B ); + ret =readx_poll_timeout (readl, c->base +VFF_EN , tmp, + tmp ==0 ,10 ,100 ); +if (ret) +dev_err (c->vc.chan.device->dev,"stop: fail, debug=0x%x\n" , +mtk_uart_apdma_read (c,VFF_DEBUG_STATUS )); + +mtk_uart_apdma_write (c,VFF_STOP ,VFF_STOP_CLR_B ); +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_INT_EN_CLR_B ); + +if (c->cfg.direction ==DMA_DEV_TO_MEM ) +mtk_uart_apdma_write (c,VFF_INT_FLAG ,VFF_RX_INT_FLAG_CLR_B ); +else if (c->cfg.direction ==DMA_MEM_TO_DEV ) +mtk_uart_apdma_write (c,VFF_INT_FLAG ,VFF_TX_INT_FLAG_CLR_B ); +
drivers/dma/mediatek/8250_mtk_dma.c line 436
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+spin_unlock_irqrestore (&c->vc.lock, flags); + +return 0 ; +} + +static int mtk_uart_apdma_device_pause (struct dma_chan *chan) +{ +/* just for check caps pass */ +return 0 ; +}
This is still not right... Hopefully somebody more familiar with the DMA subsystem can weigh in, but maybe it's enough to wait for the current transfer to be flushed and temporarily disable interrupts? e.g. call mtk_uart_apdma_terminate_all above?
drivers/dma/mediatek/8250_mtk_dma.c line 442
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ +static int mtk_uart_apdma_device_resume (struct dma_chan *chan) +{ +/* just for check caps pass */ +return 0 ; +}
Drop this one since you don't really need it.
drivers/dma/mediatek/8250_mtk_dma.c line 446
Quoted 4 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +4
-0+ +static void mtk_uart_apdma_free (struct mtk_uart_apdmadev *mtkd) +{ +while (list_empty (&mtkd->ddev.channels) ==0 ) {
!list_empty(
Quoted 25 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +25
-0+struct mtk_chan *c =list_first_entry (&mtkd->ddev.channels, + struct mtk_chan, vc.chan.device_node); + +list_del (&c->vc.chan.device_node); +tasklet_kill (&c->vc.task); + } +} + +static const struct of_device_id mtk_uart_apdma_match[] = { + { .compatible ="mediatek,mt6577-uart-dma" , }, + {/* sentinel */ }, +}; +MODULE_DEVICE_TABLE (of, mtk_uart_apdma_match); + +static int mtk_uart_apdma_probe (struct platform_device *pdev) +{ +struct mtk_uart_apdmadev *mtkd; +struct resource *res; +struct mtk_chan *c; +unsigned int i; +int rc; + + mtkd =devm_kzalloc (&pdev->dev,sizeof (*mtkd),GFP_KERNEL ); +if (!mtkd) +return -ENOMEM ;
drivers/dma/mediatek/8250_mtk_dma.c line 481
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+ + mtkd->clk =devm_clk_get (&pdev->dev,NULL ); +if (IS_ERR (mtkd->clk)) { +dev_err (&pdev->dev,"No clock specified\n" ); + rc =PTR_ERR (mtkd->clk); +return rc; + } + +if (of_property_read_bool (pdev->dev.of_node,"dma-33bits" )) + mtkd->support_33bits = true;
I don't think this should be a device tree property. Typically we'd have multiple compatible strings for (slightly) different HW blocks, and enable 33bits only on HW that have support.
See how it's done in drivers/i2c/busses/i2c-mt65xx.c, for example.
drivers/dma/mediatek/8250_mtk_dma.c line 484
Quoted 3 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +3
-0+ + rc =dma_set_mask_and_coherent (&pdev->dev, +DMA_BIT_MASK (32 | mtkd->support_33bits));
I'd feel a little more confortable if you used a variable instead:
int dma_bits = 32;
if (support_33bits)
dma_bits = 33;
..., DMA_BIT_MASK(dma_bits));
Quoted 198 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +168
-0+if (rc) +return rc; + +dma_cap_set (DMA_SLAVE , mtkd->ddev.cap_mask); + mtkd->ddev.device_alloc_chan_resources = + mtk_uart_apdma_alloc_chan_resources; + mtkd->ddev.device_free_chan_resources = + mtk_uart_apdma_free_chan_resources; + mtkd->ddev.device_tx_status = mtk_uart_apdma_tx_status; + mtkd->ddev.device_issue_pending = mtk_uart_apdma_issue_pending; + mtkd->ddev.device_prep_slave_sg = mtk_uart_apdma_prep_slave_sg; + mtkd->ddev.device_config = mtk_uart_apdma_slave_config; + mtkd->ddev.device_pause = mtk_uart_apdma_device_pause; + mtkd->ddev.device_resume = mtk_uart_apdma_device_resume; + mtkd->ddev.device_terminate_all = mtk_uart_apdma_terminate_all; + mtkd->ddev.src_addr_widths =BIT (DMA_SLAVE_BUSWIDTH_1_BYTE ); + mtkd->ddev.dst_addr_widths =BIT (DMA_SLAVE_BUSWIDTH_1_BYTE ); + mtkd->ddev.directions =BIT (DMA_DEV_TO_MEM ) |BIT (DMA_MEM_TO_DEV ); + mtkd->ddev.residue_granularity =DMA_RESIDUE_GRANULARITY_SEGMENT ; + mtkd->ddev.dev = &pdev->dev; +INIT_LIST_HEAD (&mtkd->ddev.channels); + +for (i =0 ; i <MTK_UART_APDMA_CHANNELS ; i++) { + c =devm_kzalloc (mtkd->ddev.dev,sizeof (*c),GFP_KERNEL ); +if (!c) { + rc = -ENODEV ; + goto err_no_dma; + } + + res =platform_get_resource (pdev,IORESOURCE_MEM , i); +if (!res) { + rc = -ENODEV ; + goto err_no_dma; + } + + c->base =devm_ioremap_resource (&pdev->dev, res); +if (IS_ERR (c->base)) { + rc =PTR_ERR (c->base); + goto err_no_dma; + } + c->requested = false; + c->vc.desc_free = mtk_uart_apdma_desc_free; +vchan_init (&c->vc, &mtkd->ddev); + + mtkd->dma_irq[i] =platform_get_irq (pdev, i); +if ((int )mtkd->dma_irq[i] <0 ) { +dev_err (&pdev->dev,"failed to get IRQ[%d]\n" , i); + rc = -EINVAL ; + goto err_no_dma; + } + } + +pm_runtime_enable (&pdev->dev); +pm_runtime_set_active (&pdev->dev); + + rc =dma_async_device_register (&mtkd->ddev); +if (rc) + goto rpm_disable; + +platform_set_drvdata (pdev, mtkd); + +if (pdev->dev.of_node) { +/* Device-tree DMA controller registration */ + rc =of_dma_controller_register (pdev->dev.of_node, + of_dma_xlate_by_chan_id, + mtkd); +if (rc) + goto dma_remove; + } + +return rc; + +dma_remove: +dma_async_device_unregister (&mtkd->ddev); +rpm_disable: +pm_runtime_disable (&pdev->dev); +err_no_dma: +mtk_uart_apdma_free (mtkd); +return rc; +} + +static int mtk_uart_apdma_remove (struct platform_device *pdev) +{ +struct mtk_uart_apdmadev *mtkd =platform_get_drvdata (pdev); + +if (pdev->dev.of_node) +of_dma_controller_free (pdev->dev.of_node); + +pm_runtime_disable (&pdev->dev); +pm_runtime_put_noidle (&pdev->dev); + +dma_async_device_unregister (&mtkd->ddev); +mtk_uart_apdma_free (mtkd); + +return 0 ; +} + +#ifdef CONFIG_PM_SLEEP +static int mtk_uart_apdma_suspend (struct device *dev) +{ +struct mtk_uart_apdmadev *mtkd =dev_get_drvdata (dev); + +if (!pm_runtime_suspended (dev)) +clk_disable_unprepare (mtkd->clk); + +return 0 ; +} + +static int mtk_uart_apdma_resume (struct device *dev) +{ +int ret; +struct mtk_uart_apdmadev *mtkd =dev_get_drvdata (dev); + +if (!pm_runtime_suspended (dev)) { + ret =clk_prepare_enable (mtkd->clk); +if (ret) +return ret; + } + +return 0 ; +} +#endif /* CONFIG_PM_SLEEP */ + +#ifdef CONFIG_PM +static int mtk_uart_apdma_runtime_suspend (struct device *dev) +{ +struct mtk_uart_apdmadev *mtkd =dev_get_drvdata (dev); + +clk_disable_unprepare (mtkd->clk); + +return 0 ; +} + +static int mtk_uart_apdma_runtime_resume (struct device *dev) +{ +int ret; +struct mtk_uart_apdmadev *mtkd =dev_get_drvdata (dev); + + ret =clk_prepare_enable (mtkd->clk); +if (ret) +return ret; + +return 0 ; +} +#endif /* CONFIG_PM */ + +static const struct dev_pm_ops mtk_uart_apdma_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(mtk_uart_apdma_suspend, mtk_uart_apdma_resume) +SET_RUNTIME_PM_OPS (mtk_uart_apdma_runtime_suspend, + mtk_uart_apdma_runtime_resume,NULL ) +}; + +static struct platform_driver mtk_uart_apdma_driver = { + .probe = mtk_uart_apdma_probe, + .remove = mtk_uart_apdma_remove, + .driver = { + .name =KBUILD_MODNAME , + .pm = &mtk_uart_apdma_pm_ops, + .of_match_table =of_match_ptr (mtk_uart_apdma_match), + }, +}; + +module_platform_driver (mtk_uart_apdma_driver); + +MODULE_DESCRIPTION ("MediaTek UART APDMA Controller Driver" ); +MODULE_AUTHOR ("Long Cheng <[email protected]>" ); +MODULE_LICENSE ("GPL v2" ); +drivers/dma/mediatek/Kconfig +11
-0@@ -1,4 +1,15 @@ +config DMA_MTK_UART + tristate "MediaTek SoCs APDMA support for UART" + depends on OF && SERIAL_8250_MT6577 + select DMA_ENGINE + select DMA_VIRTUAL_CHANNELS + help + Support for the UART DMA engine found on MediaTek MTK SoCs. + when SERIAL_8250_MT6577 is enabled, and if you want to use DMA, + you can enable the config. the DMA engine can only be used + with MediaTek SoCs. + config MTK_HSDMA tristate "MediaTek High-Speed DMA controller support" depends on ARCH_MEDIATEK || COMPILE_TESTdrivers/dma/mediatek/Makefile +1
-1@@ -1 +1,2 @@ +obj-$(CONFIG_DMA_MTK_UART) += 8250_mtk_dma.o obj-$(CONFIG_MTK_HSDMA) += mtk-hsdma.o --1.7.9.5
Re: [PATCH v9 1/2] dmaengine: 8250_mtk_dma: add MediaTek uart DMA support
Hi,
While you are making changes, here are a few more:
Quoted 5 lines · Nicolas Boichat
drivers/dma/mediatek/Kconfig +0
-0
drivers/dma/mediatek/Kconfig line 9
Quoted 9 lines
drivers/dma/mediatek/Kconfig +8
-0@@ -1,4 +1,15 @@ +config DMA_MTK_UART + tristate "MediaTek SoCs APDMA support for UART" + depends on OF && SERIAL_8250_MT6577 + select DMA_ENGINE + select DMA_VIRTUAL_CHANNELS + help + Support for the UART DMA engine found on MediaTek MTK SoCs. + when SERIAL_8250_MT6577 is enabled, and if you want to use DMA,
When
drivers/dma/mediatek/Kconfig line 10
Quoted 1 line
drivers/dma/mediatek/Kconfig +1
-0+ you can enable the config. the DMA engine can only be used
The
drivers/dma/mediatek/Kconfig line 12
Quoted 2 lines
drivers/dma/mediatek/Kconfig +2
-0+ with MediaTek SoCs. +
Also, use tabs to indent instead of spaces.
The lines (tristate, depends, select, and help) should be indented with one tab. The help text lines should be indented with one tab + 2 spaces.
drivers/dma/mediatek/Kconfig line 15
Quoted 3 lines
drivers/dma/mediatek/Kconfig +0
-0config MTK_HSDMA tristate "MediaTek High-Speed DMA controller support" depends on ARCH_MEDIATEK || COMPILE_TEST
thanks,
Re: [PATCH v9 1/2] dmaengine: 8250_mtk_dma: add MediaTek uart DMA support
Quoted 4 lines · Randy Dunlap
Hi,
While you are making changes, here are a few more:
hi
OK, thanks for your comments.
Quoted 19 lines · Nicolas Boichat
Quoted 5 lines
drivers/dma/mediatek/Kconfig +0
-0drivers/dma/mediatek/Kconfig line 9
Quoted 9 lines
drivers/dma/mediatek/Kconfig +8
-0@@ -1,4 +1,15 @@ +config DMA_MTK_UART + tristate "MediaTek SoCs APDMA support for UART" + depends on OF && SERIAL_8250_MT6577 + select DMA_ENGINE + select DMA_VIRTUAL_CHANNELS + help + Support for the UART DMA engine found on MediaTek MTK SoCs. + when SERIAL_8250_MT6577 is enabled, and if you want to use DMA,When
Quoted 7 lines
drivers/dma/mediatek/Kconfig line 10
Quoted 1 line
drivers/dma/mediatek/Kconfig +1
-0+ you can enable the config. the DMA engine can only be usedThe
Quoted 2 lines
drivers/dma/mediatek/Kconfig +2
-0+ with MediaTek SoCs. +
above, i will modify.
Quoted 4 lines
Also, use tabs to indent instead of spaces.
The lines (tristate, depends, select, and help) should be indented with one tab. The help text lines should be indented with one tab + 2 spaces.
in my patch, i already do this. So don't need modify.
Quoted 6 lines
drivers/dma/mediatek/Kconfig line 15
Quoted 3 lines
drivers/dma/mediatek/Kconfig +0
-0config MTK_HSDMA tristate "MediaTek High-Speed DMA controller support" depends on ARCH_MEDIATEK || COMPILE_TESTthanks,
Re: [PATCH v9 1/2] dmaengine: 8250_mtk_dma: add MediaTek uart DMA support
In reply to Nicolas BoichatQuoted 2 lines · Nicolas Boichat
Quoted 1 line · Long Cheng
.....
Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 49
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+/* interrupt trigger level for tx */ +#define VFF_TX_THRE (n) ((n) * 7 / 8) +/* interrupt trigger level for rx */ +#define VFF_RX_THRE (n) ((n) * 3 / 4) + +#define VFF_RING_SIZE 0xffffUWell, the size is actually
0x10000. Maybe call thisVFF_RING_SIZE_MASK?
the max length is 0xffff. the bit 16 is wrap bit. our buffer is ring buffer. So not mask.
Quoted 6 lines
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+/* invert this bit when wrap ring head again*/ +#define VFF_RING_WRAP 0x10000U + +writel (val, c->base + reg); +} +
......
Quoted 15 lines
drivers/dma/mediatek/8250_mtk_dma.c line 142
Quoted 12 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +12
-0+static void mtk_uart_apdma_start_tx (struct mtk_chan *c) +{ +unsigned int len, send, left, wpt, d_wpt, tmp; +int ret; + + left =mtk_uart_apdma_read (c,VFF_LEFT_SIZE ); +if (!left) { +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_TX_INT_EN_B ); +return ; + } + +/* Wait 1sec for flush, can't sleep*/ nit: one space after ',', period after 'sleep', space before '*'.
Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 147
Quoted 5 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +5
-0+ ret =readx_poll_timeout (readl, c->base +VFF_FLUSH , tmp, + tmp !=VFF_FLUSH_B ,0 ,1000000 ); +if (ret) +dev_warn (c->vc.chan.device->dev,"tx: fail, debug=0x%x\n" , +mtk_uart_apdma_read (c,VFF_DEBUG_STATUS ));Why do we need to wait for flush now? The previous implementation did not require this...
because our HW buffer is cyclic. at one tx, if the size of data is bigger, data maybe cover. So must wait flush finish. confirm the data is right. like 128 bytes size, small length can't reproduce the issue.
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c line 154
Quoted 7 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +7
-0+ + send = min_t(unsigned int, left, c->desc->avail_len); + wpt =mtk_uart_apdma_read (c,VFF_WPT ); + len =mtk_uart_apdma_read (c,VFF_LEN ); + + d_wpt = wpt + send; +if ((d_wpt &VFF_RING_SIZE ) >= len) {I don't get why you need to add "&
VFF_RING_SIZE". If wpt + send >VFF_RING_SIZE, don't you need to toggleVFF_RING_WRAPtoo?
the longest actual length is VFF_RING_SIZE. one cyclic, will set bit[16] to ~bit[16]. the bit[0 ~ 15] is actual address. So need get rid of bit[16]
Quoted 16 lines
drivers/dma/mediatek/8250_mtk_dma.c line 165
Quoted 12 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +11
-0+ d_wpt = d_wpt - len; + d_wpt = d_wpt ^VFF_RING_WRAP ; + } +mtk_uart_apdma_write (c,VFF_WPT , d_wpt); + + c->desc->avail_len -= send; + +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_TX_INT_EN_B ); +if (mtk_uart_apdma_read (c,VFF_FLUSH ) ==0U ) +mtk_uart_apdma_write (c,VFF_FLUSH ,VFF_FLUSH_B ); +}(thanks for the rest of the changes, this looks much more readable)
Quoted 1 line
+
......
Quoted 12 lines
drivers/dma/mediatek/8250_mtk_dma.c line 436
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ +static int mtk_uart_apdma_device_pause (struct dma_chan *chan) +{ +/* just for check caps pass */ +return 0 ; +}This is still not right... Hopefully somebody more familiar with the DMA subsystem can weigh in, but maybe it's enough to wait for the current transfer to be flushed and temporarily disable interrupts? e.g. call
mtk_uart_apdma_terminate_allabove?
i had review the 8250 UART framework. just check the function pointer, not use. and our HW can't support the feature. So i just keep it at first version.
Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 442
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ +static int mtk_uart_apdma_device_resume (struct dma_chan *chan) +{ +/* just for check caps pass */ +return 0 ; +}Drop this one since you don't really need it.
ok, i will remove it.
Quoted 47 lines
drivers/dma/mediatek/8250_mtk_dma.c line 446
Quoted 4 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +4
-0+ +static void mtk_uart_apdma_free (struct mtk_uart_apdmadev *mtkd) +{ +while (list_empty (&mtkd->ddev.channels) ==0 ) {!list_empty(
Quoted 25 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +25
-0+struct mtk_chan *c =list_first_entry (&mtkd->ddev.channels, + struct mtk_chan, vc.chan.device_node); + +list_del (&c->vc.chan.device_node); +tasklet_kill (&c->vc.task); + } +} + +static const struct of_device_id mtk_uart_apdma_match[] = { + { .compatible ="mediatek,mt6577-uart-dma" , }, + {/* sentinel */ }, +}; +MODULE_DEVICE_TABLE (of, mtk_uart_apdma_match); + +static int mtk_uart_apdma_probe (struct platform_device *pdev) +{ +struct mtk_uart_apdmadev *mtkd; +struct resource *res; +struct mtk_chan *c; +unsigned int i; +int rc; + + mtkd =devm_kzalloc (&pdev->dev,sizeof (*mtkd),GFP_KERNEL ); +if (!mtkd) +return -ENOMEM ;drivers/dma/mediatek/8250_mtk_dma.c line 481
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+ + mtkd->clk =devm_clk_get (&pdev->dev,NULL ); +if (IS_ERR (mtkd->clk)) { +dev_err (&pdev->dev,"No clock specified\n" ); + rc =PTR_ERR (mtkd->clk); +return rc; + } + +if (of_property_read_bool (pdev->dev.of_node,"dma-33bits" )) + mtkd->support_33bits = true;I don't think this should be a device tree property. Typically we'd have multiple compatible strings for (slightly) different HW blocks, and enable 33bits only on HW that have support.
Quoted 2 lines
See how it's done in
drivers/i2c/busses/i2c-mt65xx.c, for example.
in MediaTek, not all IC can support 33bit. So i want to configure by DT. So don't need to modify code in New IC.
Quoted 4 lines
drivers/dma/mediatek/8250_mtk_dma.c line 484
Quoted 3 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +3
-0+ + rc =dma_set_mask_and_coherent (&pdev->dev, +DMA_BIT_MASK (32 | mtkd->support_33bits));
Quoted 9 lines
I'd feel a little more confortable if you used a variable instead:
int
dma_bits= 32;if (
support_33bits)
dma_bits= 33;...,
DMA_BIT_MASK(dma_bits));
OK, i can modify it. thanks.
Quoted 81 lines
Quoted 81 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +81
-0+if (rc) +return rc; + +dma_cap_set (DMA_SLAVE , mtkd->ddev.cap_mask); + mtkd->ddev.device_alloc_chan_resources = + mtk_uart_apdma_alloc_chan_resources; + mtkd->ddev.device_free_chan_resources = + mtk_uart_apdma_free_chan_resources; + mtkd->ddev.device_tx_status = mtk_uart_apdma_tx_status; + mtkd->ddev.device_issue_pending = mtk_uart_apdma_issue_pending; + mtkd->ddev.device_prep_slave_sg = mtk_uart_apdma_prep_slave_sg; + mtkd->ddev.device_config = mtk_uart_apdma_slave_config; + mtkd->ddev.device_pause = mtk_uart_apdma_device_pause; + mtkd->ddev.device_resume = mtk_uart_apdma_device_resume; + mtkd->ddev.device_terminate_all = mtk_uart_apdma_terminate_all; + mtkd->ddev.src_addr_widths =BIT (DMA_SLAVE_BUSWIDTH_1_BYTE ); + mtkd->ddev.dst_addr_widths =BIT (DMA_SLAVE_BUSWIDTH_1_BYTE ); + mtkd->ddev.directions =BIT (DMA_DEV_TO_MEM ) |BIT (DMA_MEM_TO_DEV ); + mtkd->ddev.residue_granularity =DMA_RESIDUE_GRANULARITY_SEGMENT ; + mtkd->ddev.dev = &pdev->dev; +INIT_LIST_HEAD (&mtkd->ddev.channels); + +for (i =0 ; i <MTK_UART_APDMA_CHANNELS ; i++) { + c =devm_kzalloc (mtkd->ddev.dev,sizeof (*c),GFP_KERNEL ); +if (!c) { + rc = -ENODEV ; + goto err_no_dma; + } + + res =platform_get_resource (pdev,IORESOURCE_MEM , i); +if (!res) { + rc = -ENODEV ; + goto err_no_dma; + } + + c->base =devm_ioremap_resource (&pdev->dev, res); +if (IS_ERR (c->base)) { + rc =PTR_ERR (c->base); + goto err_no_dma; + } + c->requested = false; + c->vc.desc_free = mtk_uart_apdma_desc_free; +vchan_init (&c->vc, &mtkd->ddev); + + mtkd->dma_irq[i] =platform_get_irq (pdev, i); +if ((int )mtkd->dma_irq[i] <0 ) { +dev_err (&pdev->dev,"failed to get IRQ[%d]\n" , i); + rc = -EINVAL ; + goto err_no_dma; + } + } + +pm_runtime_enable (&pdev->dev); +pm_runtime_set_active (&pdev->dev); + + rc =dma_async_device_register (&mtkd->ddev); +if (rc) + goto rpm_disable; + +platform_set_drvdata (pdev, mtkd); + +if (pdev->dev.of_node) { +/* Device-tree DMA controller registration */ + rc =of_dma_controller_register (pdev->dev.of_node, + of_dma_xlate_by_chan_id, + mtkd); +if (rc) + goto dma_remove; + } + +return rc; + +dma_remove: +dma_async_device_unregister (&mtkd->ddev); +rpm_disable: +pm_runtime_disable (&pdev->dev); +err_no_dma: +mtk_uart_apdma_free (mtkd); +return rc; +} +
......
Vinod Koul
maintainerRe: [PATCH v9 1/2] dmaengine: 8250_mtk_dma: add MediaTek uart DMA support
In reply to Long ChengQuoted 3 lines · Long Cheng
In DMA engine framework, add 8250 uart dma to support MediaTek uart. If MediaTek uart
enabled(SERIAL_8250_MT6577), and want to improve the performance, can enable the function.
Is the DMA controller UART specific, can it work with other controllers as well, if so you should get rid of uart name in patch
Quoted 1 line
+#define
MTK_UART_APDMA_CHANNELS(CONFIG_SERIAL_8250_NR_UARTS* 2)
Why are the channels not coming from DT?
drivers/dma/mediatek/8250_mtk_dma.c line 36
Quoted 8 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +8
-0+ +#define VFF_EN_B BIT(0) +#define VFF_STOP_B BIT(0) +#define VFF_FLUSH_B BIT(0) +#define VFF_4G_SUPPORT_B BIT(0) +#define VFF_RX_INT_EN0_B BIT(0)/*rx valid size >= vff thre*/ +#define VFF_RX_INT_EN1_B BIT(1) +#define VFF_TX_INT_EN_B BIT(0)/*tx left size >= vff thre*/
space around /* space */ also run checkpatch to check for style errors
Quoted 49 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +49
-0+static void mtk_uart_apdma_start_tx (struct mtk_chan *c) +{ +unsigned int len, send, left, wpt, d_wpt, tmp; +int ret; + + left =mtk_uart_apdma_read (c,VFF_LEFT_SIZE ); +if (!left) { +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_TX_INT_EN_B ); +return ; + } + +/* Wait 1sec for flush, can't sleep*/ + ret =readx_poll_timeout (readl, c->base +VFF_FLUSH , tmp, + tmp !=VFF_FLUSH_B ,0 ,1000000 ); +if (ret) +dev_warn (c->vc.chan.device->dev,"tx: fail, debug=0x%x\n" , +mtk_uart_apdma_read (c,VFF_DEBUG_STATUS )); + + send = min_t(unsigned int, left, c->desc->avail_len); + wpt =mtk_uart_apdma_read (c,VFF_WPT ); + len =mtk_uart_apdma_read (c,VFF_LEN ); + + d_wpt = wpt + send; +if ((d_wpt &VFF_RING_SIZE ) >= len) { + d_wpt = d_wpt - len; + d_wpt = d_wpt ^VFF_RING_WRAP ; + } +mtk_uart_apdma_write (c,VFF_WPT , d_wpt); + + c->desc->avail_len -= send; + +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_TX_INT_EN_B ); +if (mtk_uart_apdma_read (c,VFF_FLUSH ) ==0U ) +mtk_uart_apdma_write (c,VFF_FLUSH ,VFF_FLUSH_B ); +} + +static void mtk_uart_apdma_start_rx (struct mtk_chan *c) +{ +struct mtk_uart_apdma_desc *d = c->desc; +unsigned int len, wg, rg, cnt; + +if ((mtk_uart_apdma_read (c,VFF_VALID_SIZE ) ==0U ) || + !d || !vchan_next_desc (&c->vc)) +return ; + + len =mtk_uart_apdma_read (c,VFF_LEN ); + rg =mtk_uart_apdma_read (c,VFF_RPT ); + wg =mtk_uart_apdma_read (c,VFF_WPT ); +if ((rg ^ wg) &VFF_RING_WRAP )
drivers/dma/mediatek/8250_mtk_dma.c line 189
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+ cnt = (wg &VFF_RING_SIZE ) + len - (rg &VFF_RING_SIZE ); + else + cnt = (wg &VFF_RING_SIZE ) - (rg &VFF_RING_SIZE ); + + c->rx_status = cnt; +mtk_uart_apdma_write (c,VFF_RPT , wg); + +list_del (&d->vd.node); +vchan_cookie_complete (&d->vd); +}
this looks odd, why do you have different rx and tx start routines?
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+static int mtk_uart_apdma_alloc_chan_resources (struct dma_chan *chan) +{ +struct mtk_uart_apdmadev *mtkd =to_mtk_uart_apdma_dev (chan->device); +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +u32 tmp; +int ret; + +pm_runtime_get_sync (mtkd->ddev.dev); + +mtk_uart_apdma_write (c,VFF_ADDR ,0 );
drivers/dma/mediatek/8250_mtk_dma.c line 238
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+mtk_uart_apdma_write (c,VFF_THRE ,0 ); +mtk_uart_apdma_write (c,VFF_LEN ,0 ); +mtk_uart_apdma_write (c,VFF_RST ,VFF_WARM_RST_B ); + + ret =readx_poll_timeout (readl, c->base +VFF_EN , tmp, + tmp ==0 ,10 ,100 ); +if (ret) { +dev_err (chan->device->dev,"dma reset: fail, timeout\n" ); +return ret; + }
register read does reset?
drivers/dma/mediatek/8250_mtk_dma.c line 244
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ +if (!c->requested) { + c->requested = true; + ret =request_irq (mtkd->dma_irq[chan->chan_id], + mtk_uart_apdma_irq_handler,IRQF_TRIGGER_NONE , +KBUILD_MODNAME , chan);
why is the irq not requested in driver probe?
Quoted 7 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +7
-0+static enum dma_status mtk_uart_apdma_tx_status (struct dma_chan *chan, +dma_cookie_t cookie, +struct dma_tx_state *txstate) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +enum dma_status ret; +unsigned long flags;
drivers/dma/mediatek/8250_mtk_dma.c line 290
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+ +if (!txstate) +return DMA_ERROR ; + + ret =dma_cookie_status (chan, cookie, txstate); +spin_lock_irqsave (&c->vc.lock, flags); +if (ret ==DMA_IN_PROGRESS ) { + c->rx_status =mtk_uart_apdma_read (c,VFF_RPT ) &VFF_RING_SIZE ; +dma_set_residue (txstate, c->rx_status); + }else if (ret ==DMA_COMPLETE && c->cfg.direction ==DMA_DEV_TO_MEM ) {
why set reside when it is complete? also reside can be null, that should be checked as well
drivers/dma/mediatek/8250_mtk_dma.c line 316
Quoted 13 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +13
-0+static struct dma_async_tx_descriptor *mtk_uart_apdma_prep_slave_sg + (struct dma_chan *chan,struct scatterlist *sgl, +unsigned int sglen,enum dma_transfer_direction dir, +unsigned long tx_flags,void *context) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +struct mtk_uart_apdma_desc *d; + +if ((dir !=DMA_DEV_TO_MEM ) && + (dir !=DMA_MEM_TO_DEV )) { +dev_err (chan->device->dev,"bad direction\n" ); +return NULL ; + }
we have a macro for this
drivers/dma/mediatek/8250_mtk_dma.c line 323
Quoted 7 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +7
-0+ +/* Now allocate and setup the descriptor */ + d =kzalloc (sizeof (*d),GFP_ATOMIC ); +if (!d) +return NULL ; + +/* sglen is 1 */
?
drivers/dma/mediatek/8250_mtk_dma.c line 361
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+static int mtk_uart_apdma_slave_config (struct dma_chan *chan, +struct dma_slave_config *cfg) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +struct mtk_uart_apdmadev *mtkd = +to_mtk_uart_apdma_dev (c->vc.chan.device); + + c->cfg = *cfg; + +if (cfg->direction ==DMA_DEV_TO_MEM ) {
fg->direction is deprecated, in fact I have removed all users recently, please do not use this
drivers/dma/mediatek/8250_mtk_dma.c line 371
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+unsigned int rx_len = cfg->src_addr_width *1024 ; + +mtk_uart_apdma_write (c,VFF_ADDR , cfg->src_addr); +mtk_uart_apdma_write (c,VFF_LEN , rx_len); +mtk_uart_apdma_write (c,VFF_THRE ,VFF_RX_THRE (rx_len)); +mtk_uart_apdma_write (c,VFF_INT_EN , +VFF_RX_INT_EN0_B |VFF_RX_INT_EN1_B ); +mtk_uart_apdma_write (c,VFF_RPT ,0 ); +mtk_uart_apdma_write (c,VFF_INT_FLAG ,VFF_RX_INT_FLAG_CLR_B ); +mtk_uart_apdma_write (c,VFF_EN ,VFF_EN_B );
why are we writing this here, we are supposed to do that when txn starts!
drivers/dma/mediatek/8250_mtk_dma.c line 442
Quoted 5 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +5
-0+static int mtk_uart_apdma_device_resume (struct dma_chan *chan) +{ +/* just for check caps pass */ +return 0 ; +}
if you do not support this please remove this!
drivers/dma/mediatek/8250_mtk_dma.c line 456
Quoted 13 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +13
-0+static void mtk_uart_apdma_free (struct mtk_uart_apdmadev *mtkd) +{ +while (list_empty (&mtkd->ddev.channels) ==0 ) { +struct mtk_chan *c =list_first_entry (&mtkd->ddev.channels, + struct mtk_chan, vc.chan.device_node); + +list_del (&c->vc.chan.device_node); +tasklet_kill (&c->vc.task); + } +} + +static const struct of_device_id mtk_uart_apdma_match[] = { + { .compatible ="mediatek,mt6577-uart-dma" , },
where is the binding document for ediatek,mt6577-uart-dma ??
Re: [PATCH v9 1/2] dmaengine: 8250_mtk_dma: add MediaTek uart DMA support
Quoted 8 lines · Vinod Koul
Quoted 3 lines · Long Cheng
In DMA engine framework, add 8250 uart dma to support MediaTek uart. If MediaTek uart
enabled(SERIAL_8250_MT6577), and want to improve the performance, can enable the function.Is the DMA controller UART specific, can it work with other controllers as well, if so you should get rid of uart name in patch
I don't know that it can work or not on other controller. but it's for MediaTek SOC
Quoted 4 lines
Quoted 1 line
+#define
MTK_UART_APDMA_CHANNELS(CONFIG_SERIAL_8250_NR_UARTS* 2)Why are the channels not coming from DT?
i will using dma-requests install of it.
Quoted 11 lines
drivers/dma/mediatek/8250_mtk_dma.c line 36
Quoted 8 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +8
-0+ +#define VFF_EN_B BIT(0) +#define VFF_STOP_B BIT(0) +#define VFF_FLUSH_B BIT(0) +#define VFF_4G_SUPPORT_B BIT(0) +#define VFF_RX_INT_EN0_B BIT(0)/*rx valid size >= vff thre*/ +#define VFF_RX_INT_EN1_B BIT(1) +#define VFF_TX_INT_EN_B BIT(0)/*tx left size >= vff thre*/ space around /* space */ also run checkpatch to check for style errors
ok.
Quoted 53 lines
Quoted 53 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +53
-0+static void mtk_uart_apdma_start_tx (struct mtk_chan *c) +{ +unsigned int len, send, left, wpt, d_wpt, tmp; +int ret; + + left =mtk_uart_apdma_read (c,VFF_LEFT_SIZE ); +if (!left) { +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_TX_INT_EN_B ); +return ; + } + +/* Wait 1sec for flush, can't sleep*/ + ret =readx_poll_timeout (readl, c->base +VFF_FLUSH , tmp, + tmp !=VFF_FLUSH_B ,0 ,1000000 ); +if (ret) +dev_warn (c->vc.chan.device->dev,"tx: fail, debug=0x%x\n" , +mtk_uart_apdma_read (c,VFF_DEBUG_STATUS )); + + send = min_t(unsigned int, left, c->desc->avail_len); + wpt =mtk_uart_apdma_read (c,VFF_WPT ); + len =mtk_uart_apdma_read (c,VFF_LEN ); + + d_wpt = wpt + send; +if ((d_wpt &VFF_RING_SIZE ) >= len) { + d_wpt = d_wpt - len; + d_wpt = d_wpt ^VFF_RING_WRAP ; + } +mtk_uart_apdma_write (c,VFF_WPT , d_wpt); + + c->desc->avail_len -= send; + +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_TX_INT_EN_B ); +if (mtk_uart_apdma_read (c,VFF_FLUSH ) ==0U ) +mtk_uart_apdma_write (c,VFF_FLUSH ,VFF_FLUSH_B ); +} + +static void mtk_uart_apdma_start_rx (struct mtk_chan *c) +{ +struct mtk_uart_apdma_desc *d = c->desc; +unsigned int len, wg, rg, cnt; + +if ((mtk_uart_apdma_read (c,VFF_VALID_SIZE ) ==0U ) || + !d || !vchan_next_desc (&c->vc)) +return ; + + len =mtk_uart_apdma_read (c,VFF_LEN ); + rg =mtk_uart_apdma_read (c,VFF_RPT ); + wg =mtk_uart_apdma_read (c,VFF_WPT ); +if ((rg ^ wg) &VFF_RING_WRAP ) + cnt = (wg &VFF_RING_SIZE ) + len - (rg &VFF_RING_SIZE ); +else + cnt = (wg &VFF_RING_SIZE ) - (rg &VFF_RING_SIZE ); +
Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 189
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ c->rx_status = cnt; +mtk_uart_apdma_write (c,VFF_RPT , wg); + +list_del (&d->vd.node); +vchan_cookie_complete (&d->vd); +}this looks odd, why do you have different rx and tx start routines?
Would you like explain it in more detail? thanks.
In tx function, will wait the last data flush done. and the count the size that send.
In Rx function, will count the size that receive.
Any way, in rx / tx, need andle WPT or RPT.
Quoted 14 lines
Quoted 14 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +14
-0+static int mtk_uart_apdma_alloc_chan_resources (struct dma_chan *chan) +{ +struct mtk_uart_apdmadev *mtkd =to_mtk_uart_apdma_dev (chan->device); +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +u32 tmp; +int ret; + +pm_runtime_get_sync (mtkd->ddev.dev); + +mtk_uart_apdma_write (c,VFF_ADDR ,0 ); +mtk_uart_apdma_write (c,VFF_THRE ,0 ); +mtk_uart_apdma_write (c,VFF_LEN ,0 ); +mtk_uart_apdma_write (c,VFF_RST ,VFF_WARM_RST_B ); +
Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 238
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ ret =readx_poll_timeout (readl, c->base +VFF_EN , tmp, + tmp ==0 ,10 ,100 ); +if (ret) { +dev_err (chan->device->dev,"dma reset: fail, timeout\n" ); +return ret; + }register read does reset?
'mtk_uart_apdma_write(c, VFF_RST, VFF_WARM_RST_B);' is reset. resd just poll reset done.
Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 244
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ +if (!c->requested) { + c->requested = true; + ret =request_irq (mtkd->dma_irq[chan->chan_id], + mtk_uart_apdma_irq_handler,IRQF_TRIGGER_NONE , +KBUILD_MODNAME , chan);why is the irq not requested in driver probe?
I have explained in below,
http://lists.infradead.org/pipermail/linux-mediatek/2018-December/016418.html
Quoted 12 lines
Quoted 12 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +12
-0+static enum dma_status mtk_uart_apdma_tx_status (struct dma_chan *chan, +dma_cookie_t cookie, +struct dma_tx_state *txstate) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +enum dma_status ret; +unsigned long flags; + +if (!txstate) +return DMA_ERROR ; + + ret =dma_cookie_status (chan, cookie, txstate);
Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 290
Quoted 5 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +5
-0+spin_lock_irqsave (&c->vc.lock, flags); +if (ret ==DMA_IN_PROGRESS ) { + c->rx_status =mtk_uart_apdma_read (c,VFF_RPT ) &VFF_RING_SIZE ; +dma_set_residue (txstate, c->rx_status); + }else if (ret ==DMA_COMPLETE && c->cfg.direction ==DMA_DEV_TO_MEM ) {why set reside when it is complete? also reside can be null, that should be checked as well
In different status, set different reside.
Quoted 7 lines
Quoted 7 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +7
-0+static struct dma_async_tx_descriptor *mtk_uart_apdma_prep_slave_sg + (struct dma_chan *chan,struct scatterlist *sgl, +unsigned int sglen,enum dma_transfer_direction dir, +unsigned long tx_flags,void *context) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +struct mtk_uart_apdma_desc *d;
Quoted 8 lines
drivers/dma/mediatek/8250_mtk_dma.c line 316
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ +if ((dir !=DMA_DEV_TO_MEM ) && + (dir !=DMA_MEM_TO_DEV )) { +dev_err (chan->device->dev,"bad direction\n" ); +return NULL ; + }we have a macro for this
Thanks for your suggestion. i will modify it.
Quoted 11 lines
drivers/dma/mediatek/8250_mtk_dma.c line 323
Quoted 8 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +7
-0+ +/* Now allocate and setup the descriptor */ + d =kzalloc (sizeof (*d),GFP_ATOMIC ); +if (!d) +return NULL ; + +/* sglen is 1 */ ?
Quoted 13 lines
drivers/dma/mediatek/8250_mtk_dma.c line 361
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+static int mtk_uart_apdma_slave_config (struct dma_chan *chan, +struct dma_slave_config *cfg) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +struct mtk_uart_apdmadev *mtkd = +to_mtk_uart_apdma_dev (c->vc.chan.device); + + c->cfg = *cfg; + +if (cfg->direction ==DMA_DEV_TO_MEM ) {
fg->directionis deprecated, in fact I have removed all users recently, please do not use this
You will remove 'direction' in 'struct dma_slave_config'? if remove, how do confirm direction?
Quoted 15 lines
drivers/dma/mediatek/8250_mtk_dma.c line 371
Quoted 11 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+unsigned int rx_len = cfg->src_addr_width *1024 ; + +mtk_uart_apdma_write (c,VFF_ADDR , cfg->src_addr); +mtk_uart_apdma_write (c,VFF_LEN , rx_len); +mtk_uart_apdma_write (c,VFF_THRE ,VFF_RX_THRE (rx_len)); +mtk_uart_apdma_write (c,VFF_INT_EN , +VFF_RX_INT_EN0_B |VFF_RX_INT_EN1_B ); +mtk_uart_apdma_write (c,VFF_RPT ,0 ); +mtk_uart_apdma_write (c,VFF_INT_FLAG ,VFF_RX_INT_FLAG_CLR_B ); +mtk_uart_apdma_write (c,VFF_EN ,VFF_EN_B );why are we writing this here, we are supposed to do that when txn starts!
also you can review the link
http://lists.infradead.org/pipermail/linux-mediatek/2018-December/016418.html
Quoted 8 lines
drivers/dma/mediatek/8250_mtk_dma.c line 442
Quoted 5 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +5
-0+static int mtk_uart_apdma_device_resume (struct dma_chan *chan) +{ +/* just for check caps pass */ +return 0 ; +}if you do not support this please remove this!
Quoted 16 lines
drivers/dma/mediatek/8250_mtk_dma.c line 456
Quoted 13 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +13
-0+static void mtk_uart_apdma_free (struct mtk_uart_apdmadev *mtkd) +{ +while (list_empty (&mtkd->ddev.channels) ==0 ) { +struct mtk_chan *c =list_first_entry (&mtkd->ddev.channels, + struct mtk_chan, vc.chan.device_node); + +list_del (&c->vc.chan.device_node); +tasklet_kill (&c->vc.task); + } +} + +static const struct of_device_id mtk_uart_apdma_match[] = { + { .compatible ="mediatek,mt6577-uart-dma" , },where is the binding document for ediatek,mt6577-uart-dma ??
http://lists.infradead.org/pipermail/linux-mediatek/2018-December/016154.html
Re: [PATCH v9 1/2] dmaengine: 8250_mtk_dma: add MediaTek uart DMA support
On Thu, 2019-01-10 at 18:33 +0800, Long Cheng wrote:
fix spell error
Quoted 13 lines · Vinod Koul
Quoted 8 lines · Long Cheng
Quoted 3 lines
In DMA engine framework, add 8250 uart dma to support MediaTek uart. If MediaTek uart
enabled(SERIAL_8250_MT6577), and want to improve the performance, can enable the function.Is the DMA controller UART specific, can it work with other controllers as well, if so you should get rid of uart name in patch
I don't know that it can work or not on other controller. but it's for MediaTek SOC
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
+#define
MTK_UART_APDMA_CHANNELS(CONFIG_SERIAL_8250_NR_UARTS* 2)Why are the channels not coming from DT?
i will using dma-requests install of it.
i will using 'dma-requests' instead of it.
Quoted 77 lines
Quoted 11 lines
drivers/dma/mediatek/8250_mtk_dma.c line 36
Quoted 8 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +8
-0+ +#define VFF_EN_B BIT(0) +#define VFF_STOP_B BIT(0) +#define VFF_FLUSH_B BIT(0) +#define VFF_4G_SUPPORT_B BIT(0) +#define VFF_RX_INT_EN0_B BIT(0)/*rx valid size >= vff thre*/ +#define VFF_RX_INT_EN1_B BIT(1) +#define VFF_TX_INT_EN_B BIT(0)/*tx left size >= vff thre*/ space around /* space */ also run checkpatch to check for style errors
ok.
Quoted 53 lines
Quoted 53 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +53
-0+static void mtk_uart_apdma_start_tx (struct mtk_chan *c) +{ +unsigned int len, send, left, wpt, d_wpt, tmp; +int ret; + + left =mtk_uart_apdma_read (c,VFF_LEFT_SIZE ); +if (!left) { +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_TX_INT_EN_B ); +return ; + } + +/* Wait 1sec for flush, can't sleep*/ + ret =readx_poll_timeout (readl, c->base +VFF_FLUSH , tmp, + tmp !=VFF_FLUSH_B ,0 ,1000000 ); +if (ret) +dev_warn (c->vc.chan.device->dev,"tx: fail, debug=0x%x\n" , +mtk_uart_apdma_read (c,VFF_DEBUG_STATUS )); + + send = min_t(unsigned int, left, c->desc->avail_len); + wpt =mtk_uart_apdma_read (c,VFF_WPT ); + len =mtk_uart_apdma_read (c,VFF_LEN ); + + d_wpt = wpt + send; +if ((d_wpt &VFF_RING_SIZE ) >= len) { + d_wpt = d_wpt - len; + d_wpt = d_wpt ^VFF_RING_WRAP ; + } +mtk_uart_apdma_write (c,VFF_WPT , d_wpt); + + c->desc->avail_len -= send; + +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_TX_INT_EN_B ); +if (mtk_uart_apdma_read (c,VFF_FLUSH ) ==0U ) +mtk_uart_apdma_write (c,VFF_FLUSH ,VFF_FLUSH_B ); +} + +static void mtk_uart_apdma_start_rx (struct mtk_chan *c) +{ +struct mtk_uart_apdma_desc *d = c->desc; +unsigned int len, wg, rg, cnt; + +if ((mtk_uart_apdma_read (c,VFF_VALID_SIZE ) ==0U ) || + !d || !vchan_next_desc (&c->vc)) +return ; + + len =mtk_uart_apdma_read (c,VFF_LEN ); + rg =mtk_uart_apdma_read (c,VFF_RPT ); + wg =mtk_uart_apdma_read (c,VFF_WPT ); +if ((rg ^ wg) &VFF_RING_WRAP ) + cnt = (wg &VFF_RING_SIZE ) + len - (rg &VFF_RING_SIZE ); +else + cnt = (wg &VFF_RING_SIZE ) - (rg &VFF_RING_SIZE ); +Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 189
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ c->rx_status = cnt; +mtk_uart_apdma_write (c,VFF_RPT , wg); + +list_del (&d->vd.node); +vchan_cookie_complete (&d->vd); +}this looks odd, why do you have different rx and tx start routines?
Quoted 6 lines
Would you like explain it in more detail? thanks.
In tx function, will wait the last data flush done. and the count the size that send.
In Rx function, will count the size that receive.
Any way, in rx / tx, need andle WPT or RPT.
Any way, in rx / tx, need handle WPT or RPT.
Quoted 154 lines
Quoted 14 lines
Quoted 14 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +14
-0+static int mtk_uart_apdma_alloc_chan_resources (struct dma_chan *chan) +{ +struct mtk_uart_apdmadev *mtkd =to_mtk_uart_apdma_dev (chan->device); +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +u32 tmp; +int ret; + +pm_runtime_get_sync (mtkd->ddev.dev); + +mtk_uart_apdma_write (c,VFF_ADDR ,0 ); +mtk_uart_apdma_write (c,VFF_THRE ,0 ); +mtk_uart_apdma_write (c,VFF_LEN ,0 ); +mtk_uart_apdma_write (c,VFF_RST ,VFF_WARM_RST_B ); +Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 238
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ ret =readx_poll_timeout (readl, c->base +VFF_EN , tmp, + tmp ==0 ,10 ,100 ); +if (ret) { +dev_err (chan->device->dev,"dma reset: fail, timeout\n" ); +return ret; + }register read does reset?
'
mtk_uart_apdma_write(c, VFF_RST, VFF_WARM_RST_B);' is reset. resd just poll reset done.Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 244
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ +if (!c->requested) { + c->requested = true; + ret =request_irq (mtkd->dma_irq[chan->chan_id], + mtk_uart_apdma_irq_handler,IRQF_TRIGGER_NONE , +KBUILD_MODNAME , chan);why is the irq not requested in driver probe?
I have explained in below,
http://lists.infradead.org/pipermail/linux-mediatek/2018-December/016418.htmlQuoted 12 lines
Quoted 12 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +12
-0+static enum dma_status mtk_uart_apdma_tx_status (struct dma_chan *chan, +dma_cookie_t cookie, +struct dma_tx_state *txstate) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +enum dma_status ret; +unsigned long flags; + +if (!txstate) +return DMA_ERROR ; + + ret =dma_cookie_status (chan, cookie, txstate);Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 290
Quoted 5 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +5
-0+spin_lock_irqsave (&c->vc.lock, flags); +if (ret ==DMA_IN_PROGRESS ) { + c->rx_status =mtk_uart_apdma_read (c,VFF_RPT ) &VFF_RING_SIZE ; +dma_set_residue (txstate, c->rx_status); + }else if (ret ==DMA_COMPLETE && c->cfg.direction ==DMA_DEV_TO_MEM ) {why set reside when it is complete? also reside can be null, that should be checked as well
In different status, set different reside.
Quoted 7 lines
Quoted 7 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +7
-0+static struct dma_async_tx_descriptor *mtk_uart_apdma_prep_slave_sg + (struct dma_chan *chan,struct scatterlist *sgl, +unsigned int sglen,enum dma_transfer_direction dir, +unsigned long tx_flags,void *context) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +struct mtk_uart_apdma_desc *d;Quoted 8 lines
drivers/dma/mediatek/8250_mtk_dma.c line 316
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ +if ((dir !=DMA_DEV_TO_MEM ) && + (dir !=DMA_MEM_TO_DEV )) { +dev_err (chan->device->dev,"bad direction\n" ); +return NULL ; + }we have a macro for this
Thanks for your suggestion. i will modify it.
Quoted 11 lines
drivers/dma/mediatek/8250_mtk_dma.c line 323
Quoted 8 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +7
-0+ +/* Now allocate and setup the descriptor */ + d =kzalloc (sizeof (*d),GFP_ATOMIC ); +if (!d) +return NULL ; + +/* sglen is 1 */ ?
Quoted 13 lines
drivers/dma/mediatek/8250_mtk_dma.c line 361
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+static int mtk_uart_apdma_slave_config (struct dma_chan *chan, +struct dma_slave_config *cfg) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +struct mtk_uart_apdmadev *mtkd = +to_mtk_uart_apdma_dev (c->vc.chan.device); + + c->cfg = *cfg; + +if (cfg->direction ==DMA_DEV_TO_MEM ) {
fg->directionis deprecated, in fact I have removed all users recently, please do not use thisYou will remove 'direction' in 'struct
dma_slave_config'? if remove, how do confirm direction?Quoted 15 lines
drivers/dma/mediatek/8250_mtk_dma.c line 371
Quoted 11 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+unsigned int rx_len = cfg->src_addr_width *1024 ; + +mtk_uart_apdma_write (c,VFF_ADDR , cfg->src_addr); +mtk_uart_apdma_write (c,VFF_LEN , rx_len); +mtk_uart_apdma_write (c,VFF_THRE ,VFF_RX_THRE (rx_len)); +mtk_uart_apdma_write (c,VFF_INT_EN , +VFF_RX_INT_EN0_B |VFF_RX_INT_EN1_B ); +mtk_uart_apdma_write (c,VFF_RPT ,0 ); +mtk_uart_apdma_write (c,VFF_INT_FLAG ,VFF_RX_INT_FLAG_CLR_B ); +mtk_uart_apdma_write (c,VFF_EN ,VFF_EN_B );why are we writing this here, we are supposed to do that when txn starts!
also you can review the link
http://lists.infradead.org/pipermail/linux-mediatek/2018-December/016418.htmlQuoted 8 lines
drivers/dma/mediatek/8250_mtk_dma.c line 442
Quoted 5 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +5
-0+static int mtk_uart_apdma_device_resume (struct dma_chan *chan) +{ +/* just for check caps pass */ +return 0 ; +}if you do not support this please remove this!
Quoted 16 lines
drivers/dma/mediatek/8250_mtk_dma.c line 456
Quoted 13 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +13
-0+static void mtk_uart_apdma_free (struct mtk_uart_apdmadev *mtkd) +{ +while (list_empty (&mtkd->ddev.channels) ==0 ) { +struct mtk_chan *c =list_first_entry (&mtkd->ddev.channels, + struct mtk_chan, vc.chan.device_node); + +list_del (&c->vc.chan.device_node); +tasklet_kill (&c->vc.task); + } +} + +static const struct of_device_id mtk_uart_apdma_match[] = { + { .compatible ="mediatek,mt6577-uart-dma" , },where is the binding document for ediatek,mt6577-uart-dma ??
http://lists.infradead.org/pipermail/linux-mediatek/2018-December/016154.html
Vinod Koul
maintainerRe: [PATCH v9 1/2] dmaengine: 8250_mtk_dma: add MediaTek uart DMA support
In reply to Long ChengQuoted 11 lines · Long Cheng
Quoted 7 lines · Vinod Koul
Quoted 3 lines · Long Cheng
In DMA engine framework, add 8250 uart dma to support MediaTek uart. If MediaTek uart
enabled(SERIAL_8250_MT6577), and want to improve the performance, can enable the function.Is the DMA controller UART specific, can it work with other controllers as well, if so you should get rid of uart name in patch
I don't know that it can work or not on other controller. but it's for MediaTek SOC
What I meant was that if can work with other controllers (users) apart from UART, how about say audio, spi etc!!
Quoted 152 lines
Quoted 5 lines
Quoted 2 lines
+#define
MTK_UART_APDMA_CHANNELS(CONFIG_SERIAL_8250_NR_UARTS* 2)Why are the channels not coming from DT?
i will using dma-requests install of it.
Quoted 11 lines
drivers/dma/mediatek/8250_mtk_dma.c line 36
Quoted 8 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +8
-0+ +#define VFF_EN_B BIT(0) +#define VFF_STOP_B BIT(0) +#define VFF_FLUSH_B BIT(0) +#define VFF_4G_SUPPORT_B BIT(0) +#define VFF_RX_INT_EN0_B BIT(0)/*rx valid size >= vff thre*/ +#define VFF_RX_INT_EN1_B BIT(1) +#define VFF_TX_INT_EN_B BIT(0)/*tx left size >= vff thre*/ space around /* space */ also run checkpatch to check for style errors
ok.
Quoted 53 lines
Quoted 53 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +53
-0+static void mtk_uart_apdma_start_tx (struct mtk_chan *c) +{ +unsigned int len, send, left, wpt, d_wpt, tmp; +int ret; + + left =mtk_uart_apdma_read (c,VFF_LEFT_SIZE ); +if (!left) { +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_TX_INT_EN_B ); +return ; + } + +/* Wait 1sec for flush, can't sleep*/ + ret =readx_poll_timeout (readl, c->base +VFF_FLUSH , tmp, + tmp !=VFF_FLUSH_B ,0 ,1000000 ); +if (ret) +dev_warn (c->vc.chan.device->dev,"tx: fail, debug=0x%x\n" , +mtk_uart_apdma_read (c,VFF_DEBUG_STATUS )); + + send = min_t(unsigned int, left, c->desc->avail_len); + wpt =mtk_uart_apdma_read (c,VFF_WPT ); + len =mtk_uart_apdma_read (c,VFF_LEN ); + + d_wpt = wpt + send; +if ((d_wpt &VFF_RING_SIZE ) >= len) { + d_wpt = d_wpt - len; + d_wpt = d_wpt ^VFF_RING_WRAP ; + } +mtk_uart_apdma_write (c,VFF_WPT , d_wpt); + + c->desc->avail_len -= send; + +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_TX_INT_EN_B ); +if (mtk_uart_apdma_read (c,VFF_FLUSH ) ==0U ) +mtk_uart_apdma_write (c,VFF_FLUSH ,VFF_FLUSH_B ); +} + +static void mtk_uart_apdma_start_rx (struct mtk_chan *c) +{ +struct mtk_uart_apdma_desc *d = c->desc; +unsigned int len, wg, rg, cnt; + +if ((mtk_uart_apdma_read (c,VFF_VALID_SIZE ) ==0U ) || + !d || !vchan_next_desc (&c->vc)) +return ; + + len =mtk_uart_apdma_read (c,VFF_LEN ); + rg =mtk_uart_apdma_read (c,VFF_RPT ); + wg =mtk_uart_apdma_read (c,VFF_WPT ); +if ((rg ^ wg) &VFF_RING_WRAP ) + cnt = (wg &VFF_RING_SIZE ) + len - (rg &VFF_RING_SIZE ); +else + cnt = (wg &VFF_RING_SIZE ) - (rg &VFF_RING_SIZE ); +Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 189
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ c->rx_status = cnt; +mtk_uart_apdma_write (c,VFF_RPT , wg); + +list_del (&d->vd.node); +vchan_cookie_complete (&d->vd); +}this looks odd, why do you have different rx and tx start routines?
Would you like explain it in more detail? thanks.
In tx function, will wait the last data flush done. and the count the size that send.
In Rx function, will count the size that receive.
Any way, in rx / tx, need andle WPT or RPT.Quoted 14 lines
Quoted 14 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +14
-0+static int mtk_uart_apdma_alloc_chan_resources (struct dma_chan *chan) +{ +struct mtk_uart_apdmadev *mtkd =to_mtk_uart_apdma_dev (chan->device); +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +u32 tmp; +int ret; + +pm_runtime_get_sync (mtkd->ddev.dev); + +mtk_uart_apdma_write (c,VFF_ADDR ,0 ); +mtk_uart_apdma_write (c,VFF_THRE ,0 ); +mtk_uart_apdma_write (c,VFF_LEN ,0 ); +mtk_uart_apdma_write (c,VFF_RST ,VFF_WARM_RST_B ); +Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 238
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ ret =readx_poll_timeout (readl, c->base +VFF_EN , tmp, + tmp ==0 ,10 ,100 ); +if (ret) { +dev_err (chan->device->dev,"dma reset: fail, timeout\n" ); +return ret; + }register read does reset?
'
mtk_uart_apdma_write(c, VFF_RST, VFF_WARM_RST_B);' is reset. resd just poll reset done.Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 244
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ +if (!c->requested) { + c->requested = true; + ret =request_irq (mtkd->dma_irq[chan->chan_id], + mtk_uart_apdma_irq_handler,IRQF_TRIGGER_NONE , +KBUILD_MODNAME , chan);why is the irq not requested in driver probe?
I have explained in below,
http://lists.infradead.org/pipermail/linux-mediatek/2018-December/016418.htmlQuoted 12 lines
Quoted 12 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +12
-0+static enum dma_status mtk_uart_apdma_tx_status (struct dma_chan *chan, +dma_cookie_t cookie, +struct dma_tx_state *txstate) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +enum dma_status ret; +unsigned long flags; + +if (!txstate) +return DMA_ERROR ; + + ret =dma_cookie_status (chan, cookie, txstate);Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 290
Quoted 5 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +5
-0+spin_lock_irqsave (&c->vc.lock, flags); +if (ret ==DMA_IN_PROGRESS ) { + c->rx_status =mtk_uart_apdma_read (c,VFF_RPT ) &VFF_RING_SIZE ; +dma_set_residue (txstate, c->rx_status); + }else if (ret ==DMA_COMPLETE && c->cfg.direction ==DMA_DEV_TO_MEM ) {why set reside when it is complete? also reside can be null, that should be checked as well
Quoted 1 line
In different status, set different reside.
Can you explain that..
Quoted 43 lines
Quoted 16 lines
Quoted 4 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +3
-0+static struct dma_async_tx_descriptor *mtk_uart_apdma_prep_slave_sg + (struct dma_chan *chan, struct scatterlist *sgl, + unsigned int sglen, enum dma_transfer_direction dir,drivers/dma/mediatek/8250_mtk_dma.c line 316
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+ unsigned long tx_flags, void *context) +{ + struct mtk_chan *c = to_mtk_uart_apdma_chan(chan); +struct mtk_uart_apdma_desc *d; + +if ((dir !=DMA_DEV_TO_MEM ) && + (dir !=DMA_MEM_TO_DEV )) { +dev_err (chan->device->dev,"bad direction\n" ); +return NULL ; + }we have a macro for this
Thanks for your suggestion. i will modify it.
Quoted 11 lines
drivers/dma/mediatek/8250_mtk_dma.c line 323
Quoted 8 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +7
-0+ +/* Now allocate and setup the descriptor */ + d =kzalloc (sizeof (*d),GFP_ATOMIC ); +if (!d) +return NULL ; + +/* sglen is 1 */ ?
Quoted 13 lines
drivers/dma/mediatek/8250_mtk_dma.c line 361
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+static int mtk_uart_apdma_slave_config (struct dma_chan *chan, +struct dma_slave_config *cfg) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +struct mtk_uart_apdmadev *mtkd = +to_mtk_uart_apdma_dev (c->vc.chan.device); + + c->cfg = *cfg; + +if (cfg->direction ==DMA_DEV_TO_MEM ) {
fg->directionis deprecated, in fact I have removed all users recently, please do not use this
Quoted 2 lines
You will remove 'direction' in 'struct
dma_slave_config'? if remove, how do confirm direction?
Yes please use the direction argument in prep_xx calls
Re: [PATCH v9 1/2] dmaengine: 8250_mtk_dma: add MediaTek uart DMA support
Quoted 7 lines · Vinod Koul
Quoted 6 lines · Long Cheng
Quoted 5 lines · Vinod Koul
Quoted 3 lines · Long Cheng
In DMA engine framework, add 8250 uart dma to support MediaTek uart. If MediaTek uart
enabled(SERIAL_8250_MT6577), and want to improve the performance, can enable the function.
Quoted 9 lines
Quoted 5 lines
Quoted 2 lines
Is the DMA controller UART specific, can it work with other controllers as well, if so you should get rid of uart name in patch
I don't know that it can work or not on other controller. but it's for MediaTek SOC
What I meant was that if can work with other controllers (users) apart from UART, how about say audio, spi etc!!
it's just for UART APDMA. can't work on spi ...
Quoted 152 lines
Quoted 152 lines
Quoted 5 lines
Quoted 2 lines
+#define
MTK_UART_APDMA_CHANNELS(CONFIG_SERIAL_8250_NR_UARTS* 2)Why are the channels not coming from DT?
i will using dma-requests install of it.
Quoted 11 lines
drivers/dma/mediatek/8250_mtk_dma.c line 36
Quoted 8 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +8
-0+ +#define VFF_EN_B BIT(0) +#define VFF_STOP_B BIT(0) +#define VFF_FLUSH_B BIT(0) +#define VFF_4G_SUPPORT_B BIT(0) +#define VFF_RX_INT_EN0_B BIT(0)/*rx valid size >= vff thre*/ +#define VFF_RX_INT_EN1_B BIT(1) +#define VFF_TX_INT_EN_B BIT(0)/*tx left size >= vff thre*/ space around /* space */ also run checkpatch to check for style errors
ok.
Quoted 53 lines
Quoted 53 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +53
-0+static void mtk_uart_apdma_start_tx (struct mtk_chan *c) +{ +unsigned int len, send, left, wpt, d_wpt, tmp; +int ret; + + left =mtk_uart_apdma_read (c,VFF_LEFT_SIZE ); +if (!left) { +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_TX_INT_EN_B ); +return ; + } + +/* Wait 1sec for flush, can't sleep*/ + ret =readx_poll_timeout (readl, c->base +VFF_FLUSH , tmp, + tmp !=VFF_FLUSH_B ,0 ,1000000 ); +if (ret) +dev_warn (c->vc.chan.device->dev,"tx: fail, debug=0x%x\n" , +mtk_uart_apdma_read (c,VFF_DEBUG_STATUS )); + + send = min_t(unsigned int, left, c->desc->avail_len); + wpt =mtk_uart_apdma_read (c,VFF_WPT ); + len =mtk_uart_apdma_read (c,VFF_LEN ); + + d_wpt = wpt + send; +if ((d_wpt &VFF_RING_SIZE ) >= len) { + d_wpt = d_wpt - len; + d_wpt = d_wpt ^VFF_RING_WRAP ; + } +mtk_uart_apdma_write (c,VFF_WPT , d_wpt); + + c->desc->avail_len -= send; + +mtk_uart_apdma_write (c,VFF_INT_EN ,VFF_TX_INT_EN_B ); +if (mtk_uart_apdma_read (c,VFF_FLUSH ) ==0U ) +mtk_uart_apdma_write (c,VFF_FLUSH ,VFF_FLUSH_B ); +} + +static void mtk_uart_apdma_start_rx (struct mtk_chan *c) +{ +struct mtk_uart_apdma_desc *d = c->desc; +unsigned int len, wg, rg, cnt; + +if ((mtk_uart_apdma_read (c,VFF_VALID_SIZE ) ==0U ) || + !d || !vchan_next_desc (&c->vc)) +return ; + + len =mtk_uart_apdma_read (c,VFF_LEN ); + rg =mtk_uart_apdma_read (c,VFF_RPT ); + wg =mtk_uart_apdma_read (c,VFF_WPT ); +if ((rg ^ wg) &VFF_RING_WRAP ) + cnt = (wg &VFF_RING_SIZE ) + len - (rg &VFF_RING_SIZE ); +else + cnt = (wg &VFF_RING_SIZE ) - (rg &VFF_RING_SIZE ); +Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 189
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ c->rx_status = cnt; +mtk_uart_apdma_write (c,VFF_RPT , wg); + +list_del (&d->vd.node); +vchan_cookie_complete (&d->vd); +}this looks odd, why do you have different rx and tx start routines?
Would you like explain it in more detail? thanks.
In tx function, will wait the last data flush done. and the count the size that send.
In Rx function, will count the size that receive.
Any way, in rx / tx, need andle WPT or RPT.Quoted 14 lines
Quoted 14 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +14
-0+static int mtk_uart_apdma_alloc_chan_resources (struct dma_chan *chan) +{ +struct mtk_uart_apdmadev *mtkd =to_mtk_uart_apdma_dev (chan->device); +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +u32 tmp; +int ret; + +pm_runtime_get_sync (mtkd->ddev.dev); + +mtk_uart_apdma_write (c,VFF_ADDR ,0 ); +mtk_uart_apdma_write (c,VFF_THRE ,0 ); +mtk_uart_apdma_write (c,VFF_LEN ,0 ); +mtk_uart_apdma_write (c,VFF_RST ,VFF_WARM_RST_B ); +Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 238
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ ret =readx_poll_timeout (readl, c->base +VFF_EN , tmp, + tmp ==0 ,10 ,100 ); +if (ret) { +dev_err (chan->device->dev,"dma reset: fail, timeout\n" ); +return ret; + }register read does reset?
'
mtk_uart_apdma_write(c, VFF_RST, VFF_WARM_RST_B);' is reset. resd just poll reset done.Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 244
Quoted 6 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +6
-0+ +if (!c->requested) { + c->requested = true; + ret =request_irq (mtkd->dma_irq[chan->chan_id], + mtk_uart_apdma_irq_handler,IRQF_TRIGGER_NONE , +KBUILD_MODNAME , chan);why is the irq not requested in driver probe?
I have explained in below,
http://lists.infradead.org/pipermail/linux-mediatek/2018-December/016418.htmlQuoted 21 lines
Quoted 7 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +7
-0+static enum dma_status mtk_uart_apdma_tx_status (struct dma_chan *chan, +dma_cookie_t cookie, +struct dma_tx_state *txstate) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +enum dma_status ret; +unsigned long flags;drivers/dma/mediatek/8250_mtk_dma.c line 290
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+ +if (!txstate) +return DMA_ERROR ; + + ret =dma_cookie_status (chan, cookie, txstate); +spin_lock_irqsave (&c->vc.lock, flags); +if (ret ==DMA_IN_PROGRESS ) { + c->rx_status =mtk_uart_apdma_read (c,VFF_RPT ) &VFF_RING_SIZE ; +dma_set_residue (txstate, c->rx_status); + }else if (ret ==DMA_COMPLETE && c->cfg.direction ==DMA_DEV_TO_MEM ) {why set reside when it is complete? also reside can be null, that should be checked as well
Quoted 4 lines
Quoted 1 line
In different status, set different reside.
Can you explain that..
RPT is different every time. When RX interrupt coming, update the rx_status and notify uart that there have data. One transfer is complete. Uart will call tx_status to get the length at the time of interruption. Other case, if want to get the tx_status, directly read register.
Quoted 19 lines
Quoted 19 lines
Quoted 16 lines
Quoted 4 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +3
-0+static struct dma_async_tx_descriptor *mtk_uart_apdma_prep_slave_sg + (struct dma_chan *chan, struct scatterlist *sgl, + unsigned int sglen, enum dma_transfer_direction dir,drivers/dma/mediatek/8250_mtk_dma.c line 316
Quoted 10 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+ unsigned long tx_flags, void *context) +{ + struct mtk_chan *c = to_mtk_uart_apdma_chan(chan); +struct mtk_uart_apdma_desc *d; + +if ((dir !=DMA_DEV_TO_MEM ) && + (dir !=DMA_MEM_TO_DEV )) { +dev_err (chan->device->dev,"bad direction\n" ); +return NULL ; + }we have a macro for this
Thanks for your suggestion. i will modify it.
Quoted 1 line
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
drivers/dma/mediatek/8250_mtk_dma.c line 323
Quoted 7 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +7
-0+ +/* Now allocate and setup the descriptor */ + d =kzalloc (sizeof (*d),GFP_ATOMIC ); +if (!d) +return NULL ; + +/* sglen is 1 */ ?
dmaengine_prep_slave_single is called. the parameter 'sglen' is 1. Add annotation to indicate that the total length is sg_dma_len(sgl), no more.
Quoted 15 lines
Quoted 15 lines
Quoted 14 lines
drivers/dma/mediatek/8250_mtk_dma.c line 361
Quoted 11 lines
drivers/dma/mediatek/8250_mtk_dma.c new file +10
-0+static int mtk_uart_apdma_slave_config (struct dma_chan *chan, +struct dma_slave_config *cfg) +{ +struct mtk_chan *c =to_mtk_uart_apdma_chan (chan); +struct mtk_uart_apdmadev *mtkd = +to_mtk_uart_apdma_dev (c->vc.chan.device); + + c->cfg = *cfg; + +if (cfg->direction ==DMA_DEV_TO_MEM ) {
fg->directionis deprecated, in fact I have removed all users recently, please do not use this
Quoted 4 lines
Quoted 2 lines
You will remove 'direction' in 'struct
dma_slave_config'? if remove, how do confirm direction?Yes please use the direction argument in
prep_xxcalls
I had modified on v10. thanks.
PATCH v9 2/2 arm: dts: mt2712: add uart APDMA to device tree
In reply to Long Cheng1. add uart APDMA controller device node
2. add uart 0/1/2/3/4/5 DMA function
--- arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 50 +++++++++++++++++++++++++++++ 1 file changed, 50 insertions(+)
arch/arm64/boot/dts/mediatek/mt2712e.dtsi +50 -0
@@ -300,6 +300,9 @@ interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_LOW>; clocks = <&baud_clk>, <&sys_clk>; clock-names = "baud", "bus"; + dmas = <&apdma 10 + &apdma 11>; + dma-names = "tx", "rx"; status = "disabled"; };
@@ -369,6 +372,38 @@ (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_HIGH)>; }; + apdma: dma-controller@11000400 { + compatible = "mediatek,mt2712-uart-dma", + "mediatek,mt6577-uart-dma"; + reg = <0 0x11000400 0 0x80>, + <0 0x11000480 0 0x80>, + <0 0x11000500 0 0x80>, + <0 0x11000580 0 0x80>, + <0 0x11000600 0 0x80>, + <0 0x11000680 0 0x80>, + <0 0x11000700 0 0x80>, + <0 0x11000780 0 0x80>, + <0 0x11000800 0 0x80>, + <0 0x11000880 0 0x80>, + <0 0x11000900 0 0x80>, + <0 0x11000980 0 0x80>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 105 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 106 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 107 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 108 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 109 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 111 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 112 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 113 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 114 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_AP_DMA>; + clock-names = "apdma"; + #dma-cells = <1>; + }; + auxadc: adc@11001000 { compatible = "mediatek,mt2712-auxadc"; reg = <0 0x11001000 0 0x1000>;
@@ -385,6 +420,9 @@ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_LOW>; clocks = <&baud_clk>, <&sys_clk>; clock-names = "baud", "bus"; + dmas = <&apdma 0 + &apdma 1>; + dma-names = "tx", "rx"; status = "disabled"; };
@@ -395,6 +433,9 @@ interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_LOW>; clocks = <&baud_clk>, <&sys_clk>; clock-names = "baud", "bus"; + dmas = <&apdma 2 + &apdma 3>; + dma-names = "tx", "rx"; status = "disabled"; };
@@ -405,6 +446,9 @@ interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_LOW>; clocks = <&baud_clk>, <&sys_clk>; clock-names = "baud", "bus"; + dmas = <&apdma 4 + &apdma 5>; + dma-names = "tx", "rx"; status = "disabled"; };
@@ -415,6 +459,9 @@ interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_LOW>; clocks = <&baud_clk>, <&sys_clk>; clock-names = "baud", "bus"; + dmas = <&apdma 6 + &apdma 7>; + dma-names = "tx", "rx"; status = "disabled"; };
@@ -629,6 +676,9 @@ interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_LOW>; clocks = <&baud_clk>, <&sys_clk>; clock-names = "baud", "bus"; + dmas = <&apdma 8 + &apdma 9>; + dma-names = "tx", "rx"; status = "disabled"; };