Stingray USB PHY driver support
v5 cover Stingray USB PHY driver support
These patches add Stingray USB PHY driver and its corresponding DT nodes with documentation.
This patch set is based on Linux-5.0-rc2.
Changes from v4:
- Addressed Rob Herring review comments
- Removed child nodes and added #phy-cells 1
- Added xlate function to get phy using phandle argument.
Changes from v3:
- Addressed Rob Herring review comments
- Changed compatible strings.
- updated driver based on new compatible strings.
Changes from v2:
- Addressed Kishon review comments
- Updated patchset to Linux-5.0-rc2
Changes from v1:
- Addressed Kishon review comments
- phy init call return value handle
Srinath Mannam (3):
dt-bindings: phy: Add Stingray USB PHY binding document
phy: sr-usb: Add Stingray USB PHY driver
arm64: dts: Add USB DT nodes for Stingray SoC
.../bindings/phy/brcm,stingray-usb-phy.txt | 40 +++ .../boot/dts/broadcom/stingray/stingray-usb.dtsi | 78 ++++ .../arm64/boot/dts/broadcom/stingray/stingray.dtsi | 1 + drivers/phy/broadcom/Kconfig | 11 + drivers/phy/broadcom/Makefile | 1 + drivers/phy/broadcom/phy-bcm-sr-usb.c | 393 +++++++++++++++++++++ 6 files changed, 524 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/brcm,stingray-usb-phy.txt create mode 100644 arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi create mode 100644 drivers/phy/broadcom/phy-bcm-sr-usb.c
Signature · 1 line
2.7.4
PATCH v5 1/3 dt-bindings: phy: Add Stingray USB PHY binding document
Add DT binding document for Stingray USB PHY.
--- .../bindings/phy/brcm,stingray-usb-phy.txt | 40 ++++++++++++++++++++++ 1 file changed, 40 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/brcm,stingray-usb-phy.txt
Documentation/devicetree/bindings/phy/brcm,stingray-usb-phy.txt new file +40 -0
@@ -0,0 +1,40 @@ +Broadcom Stingray USB PHY + +Required properties: + - compatible : should be one of the listed compatibles + - "brcm,sr-usb-combo-phy" is combo PHY has two PHYs, one SS and one HS. + - "brcm,sr-usb-hs-phy" is a single HS PHY. + - reg: offset and length of the PHY blocks registers + - address-cells: should be 1 + - size-cells: should be 0 + - #phy-cells: + - Must be 1 for brcm,sr-usb-combo-phy as it expects one argument to indicate + the PHY number of two PHYs. 0 for HS PHY and 1 for SS PHY. + - Must be 0 for brcm,sr-usb-hs-phy. + +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Example: + usbphy0: usb-phy@0 { + compatible = "brcm,sr-usb-combo-phy"; + reg = <0x00000000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + #phy-cells = <1>; + }; + + usbphy1: usb-phy@10000 { + compatible = "brcm,sr-usb-combo-phy"; + reg = <0x00010000 0x100>, + #address-cells = <1>; + #size-cells = <0>; + #phy-cells = <1>; + }; + + usbphy2: usb-phy@20000 { + compatible = "brcm,sr-usb-hs-phy"; + reg = <0x00020000 0x100>, + #address-cells = <1>; + #size-cells = <0>; + #phy-cells = <0>; + };
Signature · 1 line
2.7.4
Re: [PATCH v5 1/3] dt-bindings: phy: Add Stingray USB PHY binding document
Quoted 14 lines · Srinath Mannam
Add DT binding document for Stingray USB PHY.
Signed-off-by Srinath Mannam <[email protected]>--- .../bindings/phy/brcm,stingray-usb-phy.txt | 40 ++++++++++++++++++++++ 1 file changed, 40 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/brcm,stingray-usb-phy.txtDocumentation/devicetree/bindings/phy/brcm,stingray-usb-phy.txt new file +0
-0
Documentation/devicetree/bindings/phy/brcm,stingray-usb-phy.txt line 9
Quoted 10 lines
Documentation/devicetree/bindings/phy/brcm,stingray-usb-phy.txt new file +9
-0@@ -0,0 +1,40 @@ +Broadcom Stingray USB PHY + +Required properties: + - compatible : should be one of the listed compatibles + - "brcm,sr-usb-combo-phy" is combo PHY has two PHYs, one SS and one HS. + - "brcm,sr-usb-hs-phy" is a single HS PHY. + - reg: offset and length of the PHY blocks registers + - address-cells: should be 1 + - size-cells: should be 0
These can be dropped now. With that,
Quoted 34 lines
+ - #phy-cells:
Documentation/devicetree/bindings/phy/brcm,stingray-usb-phy.txt new file +30
-0+ - Must be 1 for brcm,sr-usb-combo-phy as it expects one argument to indicate + the PHY number of two PHYs. 0 for HS PHY and 1 for SS PHY. + - Must be 0 for brcm,sr-usb-hs-phy. + +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Example: + usbphy0: usb-phy@0 { + compatible = "brcm,sr-usb-combo-phy"; + reg = <0x00000000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + #phy-cells = <1>; + }; + + usbphy1: usb-phy@10000 { + compatible = "brcm,sr-usb-combo-phy"; + reg = <0x00010000 0x100>, + #address-cells = <1>; + #size-cells = <0>; + #phy-cells = <1>; + }; + + usbphy2: usb-phy@20000 { + compatible = "brcm,sr-usb-hs-phy"; + reg = <0x00020000 0x100>, + #address-cells = <1>; + #size-cells = <0>; + #phy-cells = <0>; + };Signature · 1 line
2.7.4
PATCH v5 2/3 phy: sr-usb: Add Stingray USB PHY driver
In reply to Srinath MannamUSB PHY driver supports two types of stingray USB PHYs
- Type 1 is a combo PHY contains two PHYs, one SS and one HS.
- Type 2 is a single HS PHY.
These two PHY versons support both Generic xHCI host controller driver and BDC Broadcom device controller driver.
--- drivers/phy/broadcom/Kconfig | 11 + drivers/phy/broadcom/Makefile | 1 + drivers/phy/broadcom/phy-bcm-sr-usb.c | 393 ++++++++++++++++++++++++++++++++++ 3 files changed, 405 insertions(+) create mode 100644 drivers/phy/broadcom/phy-bcm-sr-usb.c
drivers/phy/broadcom/Kconfig +11 -0
@@ -10,6 +10,17 @@ config PHY_CYGNUS_PCIE Enable this to support the Broadcom Cygnus PCIe PHY. If unsure, say N. +config PHY_BCM_SR_USB + tristate "Broadcom Stingray USB PHY driver" + depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST) + select GENERIC_PHY + default ARCH_BCM_IPROC + help + Enable this to support the Broadcom Stingray USB PHY + driver. It supports all versions of Superspeed and + Highspeed PHYs. + If unsure, say N. + config BCM_KONA_USB2_PHY tristate "Broadcom Kona USB2 PHY Driver" depends on HAS_IOMEM
drivers/phy/broadcom/Makefile +1 -0
@@ -11,3 +11,4 @@ obj-$(CONFIG_PHY_BRCM_USB) += phy-brcm-usb-dvr.o phy-brcm-usb-dvr-objs := phy-brcm-usb.o phy-brcm-usb-init.o obj-$(CONFIG_PHY_BCM_SR_PCIE) += phy-bcm-sr-pcie.o +obj-$(CONFIG_PHY_BCM_SR_USB) += phy-bcm-sr-usb.o
drivers/phy/broadcom/phy-bcm-sr-usb.c new file +393 -0
393 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v5 3/3 arm64: dts: Add USB DT nodes for Stingray SoC
In reply to Srinath MannamAdd DT nodes for
- Two xHCI host controllers
- Two BDC Broadcom USB device controller
- Five USB PHY controllers
[xHCI0] [BDC0] [xHCI1] [BDC1]
| | | | --------------- ----------------------- | | | | | [SS-PHY0] [HS-PHY0] [SS-PHY1] [HS-PHY2] [HS-PHY1]
[SS-PHY0/HS-PHY0] and [SS-PHY1/HS-PHY1] are combo PHYs has one SS and one HS PHYs. [HS-PHY2] is a single HS PHY.
xHCI use SS-PHY to detect SS devices and HS-PHY to detect HS/FS/LS devices. BDC use SS-PHY in SS mode and HS-PHY in HS mode.
xHCI0 port1 is SS-PHY0, port2 is HS-PHY0.
xHCI1 port1 is SS-PHY1, port2 is HS-PHY2 and port3 is HS-PHY1.
--- .../boot/dts/broadcom/stingray/stingray-usb.dtsi | 78 ++++++++++++++++++++++ .../arm64/boot/dts/broadcom/stingray/stingray.dtsi | 1 + 2 files changed, 79 insertions(+) create mode 100644 arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi
arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi new file +78 -0
@@ -0,0 +1,78 @@ +// SPDX-License-Identifier: (GPL-2.0 or BSD-3-Clause) +/* + *Copyright(c) 2018 Broadcom + */ + usb { + compatible = "simple-bus"; + dma-ranges; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x68500000 0x00400000>; + + usbphy0: usb-phy@0 { + compatible = "brcm,sr-usb-combo-phy"; + reg = <0x00000000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + #phy-cells = <1>; + status = "disabled"; + }; + + xhci0: usb@1000 { + compatible = "generic-xhci"; + reg = <0x00001000 0x1000>; + interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usbphy0 1>, <&usbphy0 0>; + phy-names = "phy0", "phy1"; + dma-coherent; + status = "disabled"; + }; + + bdc0: usb@2000 { + compatible = "brcm,bdc-v0.16"; + reg = <0x00002000 0x1000>; + interrupts = <GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usbphy0 0>, <&usbphy0 1>; + phy-names = "phy0", "phy1"; + dma-coherent; + status = "disabled"; + }; + + usbphy1: usb-phy@10000 { + compatible = "brcm,sr-usb-combo-phy"; + reg = <0x00010000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + #phy-cells = <1>; + status = "disabled"; + }; + + usbphy2: usb-phy@20000 { + compatible = "brcm,sr-usb-hs-phy"; + reg = <0x00020000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + #phy-cells = <0>; + status = "disabled"; + }; + + xhci1: usb@11000 { + compatible = "generic-xhci"; + reg = <0x00011000 0x1000>; + interrupts = <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usbphy1 1>, <&usbphy2>, <&usbphy1 0>; + phy-names = "phy0", "phy1", "phy2"; + dma-coherent; + status = "disabled"; + }; + + bdc1: usb@21000 { + compatible = "brcm,bdc-v0.16"; + reg = <0x00021000 0x1000>; + interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usbphy2>; + phy-names = "phy0"; + dma-coherent; + status = "disabled"; + }; + };
arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi +1 -0
@@ -287,6 +287,7 @@ #include "stingray-fs4.dtsi" #include "stingray-sata.dtsi" #include "stingray-pcie.dtsi" + #include "stingray-usb.dtsi" hsls { compatible = "simple-bus";
Signature · 1 line
2.7.4