Skip to contentSkip to conversation

arm64: meson: Add support for USB on Amlogic G12A

PATCH Superseded Neil Armstrong 4 participants 16 messages Mar 18, 2019 – Mar 20, 2019

Subsystems (6)

v3 of 6 Superseded Latest is v6 →

lore
Share & tools
lore
#0 lore raw

v3 cover arm64: meson: Add support for USB on Amlogic G12A

This patchset adds support for USB on Amlogic G12A SoCs.

This patchset is composed with :
- bindings of the PHYs
- bindings of the USB Control Glue
- PHY Drivers
- USB Control Glue driver

Device Tree nodes will be added in a separate patchset.

The Amlogic G12A USB Complex is composed of :
- 2 USB Controllers :
* DWC3 for USB2 and USB3 Host functionality
* DWC2 for USB2 Peripheral functionality
- 2 USB2 OTG PHYs, only a single one will be routed to either DWC2 to DWC3
- 1 USB3 PHY shared with PCIE funcionnality
- A Glue to control PHY routing, setup and OTG detection

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY.

This drivers supports the on-probe setup of the OTG mode, and manually via the USB Role interface. The IRQ mode change detect is yet to be added in a future patchset, mainly due to lack of hardware to validate on.

Changes since v2 at [1]:
- Collected review tags
- Removed syscon.h in usb2 phy driver
- Added comment on the USB3/PCIe switch
- Renamed dwc3_meson_g12a_usb_init_mode in glue driver
- Changed indentation in dwc3_meson_g12a_role_set
- Switched to of_get_compatible_child in glue code
- Added devm_add_action_or_reset() to disable clock in case of probe failure
- Checks priv->vbus before enabling regulator
- Switched phy_init/phy_power_on
- Removed priv->phys[i] NULL checks in suspend code
- Removed clk_disable_unprepare/clk_put in remove code

Changes since v1 at [0]:
- USB2 PHY Bindings: collected tags and updated commit log
- USB3/PCIE PHY Bindings: collected tag and updated reset list
- DWC2 Compatible: collected tags
- DWC3 Glue Bindings:
- removed clock-names and reset-names for single entries
- removed ports graph for PHYs and replaced by phys list with phy-names
- added dr_mode and optional vbus-supply
- fixed example
- USB2 PHY Driver: removed USB_SUPPORT and otg.h include
- USB3/PCIE PHY Driver: removed USB_SUPPORT, fixed comment and unused reg variable
- USB Glue Driver:
- Moved debugfs I/F to USB_ROLE_SWITCH framework
- Integrated USB Glue Control Registers offset
- Removed of graph parsing to use devm_phy_optional_get()
- Fixed PHY mode handling and OTG switching
- Simplified PHY calls by removing the NULL test
- Added optional vbus regulator handling

[1] https://lkml.kernel.org/r/[email protected]
[2] https://lkml.kernel.org/r/[email protected]

Neil Armstrong (8):
dt-bindings: phy: Add Amlogic G12A USB2 PHY Bindings
dt-bindings: phy: Add Amlogic G12A USB3+PCIE Combo PHY Bindings
dt-bindings: usb: dwc2: Add Amlogic G12A DWC2 Compatible
dt-bindings: usb: dwc3: Add Amlogic G12A DWC3 Glue Bindings
phy: amlogic: add Amlogic G12A USB2 PHY Driver
phy: amlogic: Add Amlogic G12A USB3 + PCIE Combo PHY Driver
usb: dwc2: Add Amlogic G12A DWC2 Params
usb: dwc3: Add Amlogic G12A DWC3 glue

 .../bindings/phy/meson-g12a-usb2-phy.txt      |  22 +
 .../bindings/phy/meson-g12a-usb3-pcie-phy.txt |  22 +
 .../devicetree/bindings/usb/amlogic,dwc3.txt  |  88 +++
 .../devicetree/bindings/usb/dwc2.txt          |   1 +
 drivers/phy/amlogic/Kconfig                   |  22 +
 drivers/phy/amlogic/Makefile                  |   2 +
 drivers/phy/amlogic/phy-meson-g12a-usb2.c     | 189 ++++++
 .../phy/amlogic/phy-meson-g12a-usb3-pcie.c    | 413 ++++++++++++
 drivers/usb/dwc2/params.c                     |  12 +
 drivers/usb/dwc3/Kconfig                      |  10 +
 drivers/usb/dwc3/Makefile                     |   1 +
 drivers/usb/dwc3/dwc3-meson-g12a.c            | 602 ++++++++++++++++++
 12 files changed, 1384 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/meson-g12a-usb2-phy.txt
 create mode 100644 Documentation/devicetree/bindings/phy/meson-g12a-usb3-pcie-phy.txt
 create mode 100644 drivers/phy/amlogic/phy-meson-g12a-usb2.c
 create mode 100644 drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c
 create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c
Signature · 1 line
2.20.1
#1 lore raw

PATCH v3 1/8 dt-bindings: phy: Add Amlogic G12A USB2 PHY Bindings

Add the Amlogic G12A Family USB2 OTG PHY Bindings

The PHY can work in host or peripheral modes depending on it's position. Configuration of the mode is part of the USBCTRL registers which are outside of the PHY registers.

---
 .../bindings/phy/meson-g12a-usb2-phy.txt      | 22 +++++++++++++++++++
 1 file changed, 22 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/meson-g12a-usb2-phy.txt
Documentation/devicetree/bindings/phy/meson-g12a-usb2-phy.txt new file +22 -0
new file mode 100644
index 000000000000..a6ebc3dea159
@@ -0,0 +1,22 @@
+* Amlogic G12A USB2 PHY binding
+
+Required properties:
+- compatible:	Should be "amlogic,meson-g12a-usb2-phy"
+- reg:		The base address and length of the registers
+- #phys-cells:	must be 0 (see phy-bindings.txt in this directory)
+- clocks:	a phandle to the clock of this PHY
+- clock-names:	must be "xtal"
+- resets:	a phandle to the reset line of this PHY
+- reset-names:	must be "phy"
+- phy-supply:	see phy-bindings.txt in this directory
+
+Example:
+	usb2_phy0: phy@36000 {
+		compatible = "amlogic,g12a-usb2-phy";
+		reg = <0x0 0x36000 0x0 0x2000>;
+		clocks = <&xtal>;
+		clock-names = "xtal";
+		resets = <&reset RESET_USB_PHY21>;
+		reset-names = "phy";
+		#phy-cells = <0>;
+	};
Signature · 1 line
2.20.1
#2 lore raw

PATCH v3 2/8 dt-bindings: phy: Add Amlogic G12A USB3+PCIE Combo PHY Bindings

In reply to Neil Armstrong

Add the Amlogic G12A Family USB3 + PCIE Combo PHY Bindings.

This PHY can provide exclusively USB3 or PCIE support on shared I/Os.

---
 .../bindings/phy/meson-g12a-usb3-pcie-phy.txt | 22 +++++++++++++++++++
 1 file changed, 22 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/meson-g12a-usb3-pcie-phy.txt
Documentation/devicetree/bindings/phy/meson-g12a-usb3-pcie-phy.txt new file +22 -0
new file mode 100644
index 000000000000..7cfc17e2df31
@@ -0,0 +1,22 @@
+* Amlogic G12A USB3 + PCIE Combo PHY binding
+
+Required properties:
+- compatible:	Should be "amlogic,meson-g12a-usb3-pcie-phy"
+- #phys-cells:	must be 1. The cell number is used to select the phy mode
+  as defined in <dt-bindings/phy/phy.h> between PHY_TYPE_USB3 and PHY_TYPE_PCIE
+- reg:		The base address and length of the registers
+- clocks:	a phandle to the 100MHz reference clock of this PHY
+- clock-names:	must be "ref_clk"
+- resets:	phandle to the reset lines for the PHY control
+- reset-names:	must be "phy"
+
+Example:
+	usb3_pcie_phy: phy@46000 {
+		compatible = "amlogic,g12a-usb3-pcie-phy";
+		reg = <0x0 0x46000 0x0 0x2000>;
+		clocks = <&clkc CLKID_PCIE_PLL>;
+		clock-names = "ref_clk";
+		resets = <&reset RESET_PCIE_PHY>;
+		reset-names = "phy";
+		#phy-cells = <1>;
+	};
Signature · 1 line
2.20.1
#3 lore raw

PATCH v3 3/8 dt-bindings: usb: dwc2: Add Amlogic G12A DWC2 Compatible

In reply to Neil Armstrong

Adds the specific compatible string for the DWC2 IP found in the Amlogic G12A SoC Family.

---
 Documentation/devicetree/bindings/usb/dwc2.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/usb/dwc2.txt +1 -0
index 6dc3c4a34483..e150b7b227c9 100644
@@ -14,6 +14,7 @@ Required properties:
   - "amlogic,meson8-usb": The DWC2 USB controller instance in Amlogic Meson8 SoCs;
   - "amlogic,meson8b-usb": The DWC2 USB controller instance in Amlogic Meson8b SoCs;
   - "amlogic,meson-gxbb-usb": The DWC2 USB controller instance in Amlogic S905 SoCs;
+  - "amlogic,meson-g12a-usb": The DWC2 USB controller instance in Amlogic G12A SoCs;
   - "amcc,dwc-otg": The DWC2 USB controller instance in AMCC Canyonlands 460EX SoCs;
   - snps,dwc2: A generic DWC2 USB controller with default parameters.
   - "st,stm32f4x9-fsotg": The DWC2 USB FS/HS controller instance in STM32F4x9 SoCs
Signature · 1 line
2.20.1
#4 lore raw

PATCH v3 4/8 dt-bindings: usb: dwc3: Add Amlogic G12A DWC3 Glue Bindings

In reply to Neil Armstrong

Adds the bindings for the Amlogic G12A USB Glue HW.

The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only

A glue connects these both controllers to 2 USB2 PHYs,
and optionnally to an USB3+PCIE Combo PHY shared with the PCIE controller.

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY.

The PHYs phandles are passed to the Glue node since the Glue controls the interface with the PHY, not the DWC3 controller.

---
 .../devicetree/bindings/usb/amlogic,dwc3.txt  | 88 +++++++++++++++++++
 1 file changed, 88 insertions(+)
Documentation/devicetree/bindings/usb/amlogic,dwc3.txt +88 -0
index 9a8b631904fd..b9f04e617eb7 100644
@@ -40,3 +40,91 @@ Example device nodes:
 				phy-names = "usb2-phy", "usb3-phy";
 			};
 		};
+
+Amlogic Meson G12A DWC3 USB SoC Controller Glue
+
+The Amlogic G12A embeds a DWC3 USB IP Core configured for USB2 and USB3
+in host-only mode, and a DWC2 IP Core configured for USB2 peripheral mode
+only.
+
+A glue connects the DWC3 core to USB2 PHYs and optionnaly to an USB3 PHY.
+
+One of the USB2 PHY can be re-routed in peripheral mode to a DWC2 USB IP.
+
+The DWC3 Glue controls the PHY routing and power, an interrupt line is
+connected to the Glue to serve as OTG ID change detection.
+
+Required properties:
+- compatible:	Should be "amlogic,meson-g12a-usb-ctrl"
+- clocks:	a handle for the "USB" clock
+- resets:	a handle for the shared "USB" reset line
+- reg:		The base address and length of the registers
+- interrupts:	the interrupt specifier for the OTG detection
+- phys: 	handle to used PHYs on the system
+	- a <0> phandle can be used if a PHY is not used
+- phy-names:	names of the used PHYs on the system :
+	- "usb2-phy0" for USB2 PHY0 if USBHOST_A port is used
+	- "usb2-phy1" for USB2 PHY1 if USBOTG_B port is used
+	- "usb3-phy0" for USB3 PHY if USB3_0 is used
+- dr_mode:	should be "host", "peripheral", or "otg" depending on
+	the usage and configuration of the OTG Capable port.
+	- "host" and "peripheral" means a fixed Host or Device only connection
+	- "otg" means the port can be used as both Host or Device and
+	  be switched automatically using the OTG ID pin.
+
+Optional properties:
+- vbus-supply:	should be a phandle to the regulator controlling the VBUS
+		power supply when used in OTG switchable mode
+
+Required child nodes:
+
+A child node must exist to represent the core DWC3 IP block. The name of
+the node is not important. The content of the node is defined in dwc3.txt.
+
+A child node must exist to represent the core DWC2 IP block. The name of
+the node is not important. The content of the node is defined in dwc2.txt.
+
+PHY documentation is provided in the following places:
+- Documentation/devicetree/bindings/phy/meson-g12a-usb2-phy.txt
+- Documentation/devicetree/bindings/phy/meson-g12a-usb3-pcie-phy.txt
+
+Example device nodes:
+	usb: usb@ffe09000 {
+			compatible = "amlogic,meson-g12a-usb-ctrl";
+			reg = <0x0 0xffe09000 0x0 0xa0>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&clkc CLKID_USB>;
+			resets = <&reset RESET_USB>;
+
+			dr_mode = "otg";
+
+			phys = <&usb2_phy0>, <&usb2_phy1>,
+			       <&usb3_pcie_phy PHY_TYPE_USB3>;
+			phy-names = "usb2-phy0", "usb2-phy1", "usb3-phy0";
+
+			dwc2: usb@ff400000 {
+				compatible = "amlogic,meson-g12a-usb", "snps,dwc2";
+				reg = <0x0 0xff400000 0x0 0x40000>;
+				interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
+				clock-names = "ddr";
+				phys = <&usb2_phy1>;
+				dr_mode = "peripheral";
+				g-rx-fifo-size = <192>;
+				g-np-tx-fifo-size = <128>;
+				g-tx-fifo-size = <128 128 16 16 16>;
+			};
+
+			dwc3: usb@ff500000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0xff500000 0x0 0x100000>;
+				interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+				dr_mode = "host";
+				snps,dis_u2_susphy_quirk;
+				snps,quirk-frame-length-adjustment;
+			};
+	};
Signature · 1 line
2.20.1
#5 lore raw

PATCH v3 5/8 phy: amlogic: add Amlogic G12A USB2 PHY Driver

In reply to Neil Armstrong

This adds support for the USB2 PHY found in the Amlogic G12A SoC Family.

It supports Host and/or Peripheral mode, depending on it's position. The first PHY is only used as Host, but the second supports Dual modes defined by the USB Control Glue HW in front of the USB Controllers.

---
 drivers/phy/amlogic/Kconfig               |  11 ++
 drivers/phy/amlogic/Makefile              |   1 +
 drivers/phy/amlogic/phy-meson-g12a-usb2.c | 189 ++++++++++++++++++++++
 3 files changed, 201 insertions(+)
 create mode 100644 drivers/phy/amlogic/phy-meson-g12a-usb2.c
drivers/phy/amlogic/Kconfig +11 -0
index 23fe1cda2f70..560ff0f1ed4c 100644
@@ -36,3 +36,14 @@ config PHY_MESON_GXL_USB3
 	  Enable this to support the Meson USB3 PHY and OTG detection
 	  IP block found in Meson GXL and GXM SoCs.
 	  If unsure, say N.
+
+config PHY_MESON_G12A_USB2
+	tristate "Meson G12A USB2 PHY driver"
+	default ARCH_MESON
+	depends on OF && (ARCH_MESON || COMPILE_TEST)
+	select GENERIC_PHY
+	select REGMAP_MMIO
+	help
+	  Enable this to support the Meson USB2 PHYs found in Meson
+	  G12A SoCs.
+	  If unsure, say N.
drivers/phy/amlogic/Makefile +1 -0
index 4fd8848c194d..7d4d10f5a6b3 100644
@@ -1,3 +1,4 @@
 obj-$(CONFIG_PHY_MESON8B_USB2)		+= phy-meson8b-usb2.o
 obj-$(CONFIG_PHY_MESON_GXL_USB2)	+= phy-meson-gxl-usb2.o
+obj-$(CONFIG_PHY_MESON_G12A_USB2)	+= phy-meson-g12a-usb2.o
 obj-$(CONFIG_PHY_MESON_GXL_USB3)	+= phy-meson-gxl-usb3.o
drivers/phy/amlogic/phy-meson-g12a-usb2.c new file +189 -0

189 lines not on this page · raw message

#6 lore raw

Re: [PATCH v3 5/8] phy: amlogic: add Amlogic G12A USB2 PHY Driver

Hi,

Quoted 119 lines · Neil Armstrong

This adds support for the USB2 PHY found in the Amlogic G12A SoC Family.

It supports Host and/or Peripheral mode, depending on it's position. The first PHY is only used as Host, but the second supports Dual modes defined by the USB Control Glue HW in front of the USB Controllers.

---
 drivers/phy/amlogic/Kconfig               |  11 ++
 drivers/phy/amlogic/Makefile              |   1 +
 drivers/phy/amlogic/phy-meson-g12a-usb2.c | 189 ++++++++++++++++++++++
 3 files changed, 201 insertions(+)
 create mode 100644 drivers/phy/amlogic/phy-meson-g12a-usb2.c
drivers/phy/amlogic/Kconfig +11 -0
index 23fe1cda2f70..560ff0f1ed4c 100644
@@ -36,3 +36,14 @@ config PHY_MESON_GXL_USB3
 	  Enable this to support the Meson USB3 PHY and OTG detection
 	  IP block found in Meson GXL and GXM SoCs.
 	  If unsure, say N.
+
+config PHY_MESON_G12A_USB2
+	tristate "Meson G12A USB2 PHY driver"
+	default ARCH_MESON
+	depends on OF && (ARCH_MESON || COMPILE_TEST)
+	select GENERIC_PHY
+	select REGMAP_MMIO
+	help
+	  Enable this to support the Meson USB2 PHYs found in Meson
+	  G12A SoCs.
+	  If unsure, say N.
drivers/phy/amlogic/Makefile +1 -0
index 4fd8848c194d..7d4d10f5a6b3 100644
@@ -1,3 +1,4 @@
 obj-$(CONFIG_PHY_MESON8B_USB2)		+= phy-meson8b-usb2.o
 obj-$(CONFIG_PHY_MESON_GXL_USB2)	+= phy-meson-gxl-usb2.o
+obj-$(CONFIG_PHY_MESON_G12A_USB2)	+= phy-meson-g12a-usb2.o
 obj-$(CONFIG_PHY_MESON_GXL_USB3)	+= phy-meson-gxl-usb3.o
drivers/phy/amlogic/phy-meson-g12a-usb2.c new file +70 -0
new file mode 100644
index 000000000000..9f35259f237f
@@ -0,0 +1,189 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Meson G12A USB2 PHY driver
+ *
+ * Copyright (C) 2017 Martin Blumenstingl <[email protected]>
+ * Copyright (C) 2017 Amlogic, Inc. All rights reserved
+ * Copyright (C) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <[email protected]>
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+
+#define PHY_CTRL_R0						0x0
+#define PHY_CTRL_R1						0x4
+#define PHY_CTRL_R2						0x8
+#define PHY_CTRL_R3						0xc
+#define PHY_CTRL_R4						0x10
+#define PHY_CTRL_R5						0x14
+#define PHY_CTRL_R6						0x18
+#define PHY_CTRL_R7						0x1c
+#define PHY_CTRL_R8						0x20
+#define PHY_CTRL_R9						0x24
+#define PHY_CTRL_R10						0x28
+#define PHY_CTRL_R11						0x2c
+#define PHY_CTRL_R12						0x30
+#define PHY_CTRL_R13						0x34
+#define PHY_CTRL_R14						0x38
+#define PHY_CTRL_R15						0x3c
+#define PHY_CTRL_R16						0x40
+#define PHY_CTRL_R17						0x44
+#define PHY_CTRL_R18						0x48
+#define PHY_CTRL_R19						0x4c
+#define PHY_CTRL_R20						0x50
+#define PHY_CTRL_R21						0x54
+#define PHY_CTRL_R22						0x58
+#define PHY_CTRL_R23						0x5c
+
+#define RESET_COMPLETE_TIME					1000
+#define PLL_RESET_COMPLETE_TIME					100
+
+struct phy_meson_g12a_usb2_priv {
+	struct device		*dev;
+	struct regmap		*regmap;
+	struct clk		*clk;
+	struct reset_control	*reset;
+};
+
+static const struct regmap_config phy_meson_g12a_usb2_regmap_conf = {
+	.reg_bits = 8,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = PHY_CTRL_R23,
+};
+
+static int phy_meson_g12a_usb2_init(struct phy *phy)
+{
+	struct phy_meson_g12a_usb2_priv *priv = phy_get_drvdata(phy);
+	int ret;
+
+	ret = reset_control_reset(priv->reset);
+	if (ret)
+		return ret;

drivers/phy/amlogic/phy-meson-g12a-usb2.c line 80

Quoted 10 lines
drivers/phy/amlogic/phy-meson-g12a-usb2.c new file +10 -0
+
+	udelay(RESET_COMPLETE_TIME);
+
+	/* usb2_otg_aca_en == 0 */
+	regmap_update_bits(priv->regmap, PHY_CTRL_R21, BIT(2), 0);
+
+	/* PLL Setup : 24MHz * 20 / 1 = 480MHz */
+	regmap_write(priv->regmap, PHY_CTRL_R16, 0x39400414);
+	regmap_write(priv->regmap, PHY_CTRL_R17, 0x927e0000);
+	regmap_write(priv->regmap, PHY_CTRL_R18, 0xac5f49e5);

Please add macros for each of the individual bit-fields.

drivers/phy/amlogic/phy-meson-g12a-usb2.c line 85

Quoted 5 lines
drivers/phy/amlogic/phy-meson-g12a-usb2.c new file +5 -0
+
+	udelay(PLL_RESET_COMPLETE_TIME);
+
+	/* UnReset PLL */
+	regmap_write(priv->regmap, PHY_CTRL_R16, 0x19400414);

Here too..

Thanks
Kishon

#7 lore raw

Re: [PATCH v3 5/8] phy: amlogic: add Amlogic G12A USB2 PHY Driver

Quoted 126 lines · Kishon Vijay Abraham I

Hi,

Quoted 123 lines · Neil Armstrong

This adds support for the USB2 PHY found in the Amlogic G12A SoC Family.

It supports Host and/or Peripheral mode, depending on it's position. The first PHY is only used as Host, but the second supports Dual modes defined by the USB Control Glue HW in front of the USB Controllers.

---
 drivers/phy/amlogic/Kconfig               |  11 ++
 drivers/phy/amlogic/Makefile              |   1 +
 drivers/phy/amlogic/phy-meson-g12a-usb2.c | 189 ++++++++++++++++++++++
 3 files changed, 201 insertions(+)
 create mode 100644 drivers/phy/amlogic/phy-meson-g12a-usb2.c
drivers/phy/amlogic/Kconfig +11 -0
index 23fe1cda2f70..560ff0f1ed4c 100644
@@ -36,3 +36,14 @@ config PHY_MESON_GXL_USB3
 	  Enable this to support the Meson USB3 PHY and OTG detection
 	  IP block found in Meson GXL and GXM SoCs.
 	  If unsure, say N.
+
+config PHY_MESON_G12A_USB2
+	tristate "Meson G12A USB2 PHY driver"
+	default ARCH_MESON
+	depends on OF && (ARCH_MESON || COMPILE_TEST)
+	select GENERIC_PHY
+	select REGMAP_MMIO
+	help
+	  Enable this to support the Meson USB2 PHYs found in Meson
+	  G12A SoCs.
+	  If unsure, say N.
drivers/phy/amlogic/Makefile +1 -0
index 4fd8848c194d..7d4d10f5a6b3 100644
@@ -1,3 +1,4 @@
 obj-$(CONFIG_PHY_MESON8B_USB2)		+= phy-meson8b-usb2.o
 obj-$(CONFIG_PHY_MESON_GXL_USB2)	+= phy-meson-gxl-usb2.o
+obj-$(CONFIG_PHY_MESON_G12A_USB2)	+= phy-meson-g12a-usb2.o
 obj-$(CONFIG_PHY_MESON_GXL_USB3)	+= phy-meson-gxl-usb3.o
drivers/phy/amlogic/phy-meson-g12a-usb2.c new file +74 -0
new file mode 100644
index 000000000000..9f35259f237f
@@ -0,0 +1,189 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Meson G12A USB2 PHY driver
+ *
+ * Copyright (C) 2017 Martin Blumenstingl <[email protected]>
+ * Copyright (C) 2017 Amlogic, Inc. All rights reserved
+ * Copyright (C) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <[email protected]>
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+
+#define PHY_CTRL_R0						0x0
+#define PHY_CTRL_R1						0x4
+#define PHY_CTRL_R2						0x8
+#define PHY_CTRL_R3						0xc
+#define PHY_CTRL_R4						0x10
+#define PHY_CTRL_R5						0x14
+#define PHY_CTRL_R6						0x18
+#define PHY_CTRL_R7						0x1c
+#define PHY_CTRL_R8						0x20
+#define PHY_CTRL_R9						0x24
+#define PHY_CTRL_R10						0x28
+#define PHY_CTRL_R11						0x2c
+#define PHY_CTRL_R12						0x30
+#define PHY_CTRL_R13						0x34
+#define PHY_CTRL_R14						0x38
+#define PHY_CTRL_R15						0x3c
+#define PHY_CTRL_R16						0x40
+#define PHY_CTRL_R17						0x44
+#define PHY_CTRL_R18						0x48
+#define PHY_CTRL_R19						0x4c
+#define PHY_CTRL_R20						0x50
+#define PHY_CTRL_R21						0x54
+#define PHY_CTRL_R22						0x58
+#define PHY_CTRL_R23						0x5c
+
+#define RESET_COMPLETE_TIME					1000
+#define PLL_RESET_COMPLETE_TIME					100
+
+struct phy_meson_g12a_usb2_priv {
+	struct device		*dev;
+	struct regmap		*regmap;
+	struct clk		*clk;
+	struct reset_control	*reset;
+};
+
+static const struct regmap_config phy_meson_g12a_usb2_regmap_conf = {
+	.reg_bits = 8,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = PHY_CTRL_R23,
+};
+
+static int phy_meson_g12a_usb2_init(struct phy *phy)
+{
+	struct phy_meson_g12a_usb2_priv *priv = phy_get_drvdata(phy);
+	int ret;
+
+	ret = reset_control_reset(priv->reset);
+	if (ret)
+		return ret;
+
+	udelay(RESET_COMPLETE_TIME);
+
+	/* usb2_otg_aca_en == 0 */
Quoted 8 lines

drivers/phy/amlogic/phy-meson-g12a-usb2.c line 80

Quoted 6 lines
drivers/phy/amlogic/phy-meson-g12a-usb2.c new file +6 -0
+	regmap_update_bits(priv->regmap, PHY_CTRL_R21, BIT(2), 0);
+
+	/* PLL Setup : 24MHz * 20 / 1 = 480MHz */
+	regmap_write(priv->regmap, PHY_CTRL_R16, 0x39400414);
+	regmap_write(priv->regmap, PHY_CTRL_R17, 0x927e0000);
+	regmap_write(priv->regmap, PHY_CTRL_R18, 0xac5f49e5);

Please add macros for each of the individual bit-fields.

Will resent with this added.

Neil

Quoted 11 lines

drivers/phy/amlogic/phy-meson-g12a-usb2.c line 85

Quoted 5 lines
drivers/phy/amlogic/phy-meson-g12a-usb2.c new file +5 -0
+
+	udelay(PLL_RESET_COMPLETE_TIME);
+
+	/* UnReset PLL */
+	regmap_write(priv->regmap, PHY_CTRL_R16, 0x19400414);

Here too..

Thanks
Kishon

#8 lore raw

PATCH v3 6/8 phy: amlogic: Add Amlogic G12A USB3 + PCIE Combo PHY Driver

In reply to Neil Armstrong

This adds support for the shared USB3 + PCIE PHY found in the Amlogic G12A SoC Family.

It supports USB3 Host mode or PCIE 2.0 mode, depending on the layout of the board.

Selection is done by the #phy-cells, making the mode static and exclusive.

---
 drivers/phy/amlogic/Kconfig                   |  11 +
 drivers/phy/amlogic/Makefile                  |   1 +
 .../phy/amlogic/phy-meson-g12a-usb3-pcie.c    | 413 ++++++++++++++++++
 3 files changed, 425 insertions(+)
 create mode 100644 drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c
drivers/phy/amlogic/Kconfig +11 -0
index 560ff0f1ed4c..4c08c1ccdd04 100644
@@ -47,3 +47,14 @@ config PHY_MESON_G12A_USB2
 	  Enable this to support the Meson USB2 PHYs found in Meson
 	  G12A SoCs.
 	  If unsure, say N.
+
+config PHY_MESON_G12A_USB3_PCIE
+	tristate "Meson G12A USB3+PCIE Combo PHY driver"
+	default ARCH_MESON
+	depends on OF && (ARCH_MESON || COMPILE_TEST)
+	select GENERIC_PHY
+	select REGMAP_MMIO
+	help
+	  Enable this to support the Meson USB3 + PCIE Combo PHY found
+	  in Meson G12A SoCs.
+	  If unsure, say N.
drivers/phy/amlogic/Makefile +1 -0
index 7d4d10f5a6b3..fdd008e1b19b 100644
@@ -2,3 +2,4 @@ obj-$(CONFIG_PHY_MESON8B_USB2)		+= phy-meson8b-usb2.o
 obj-$(CONFIG_PHY_MESON_GXL_USB2)	+= phy-meson-gxl-usb2.o
 obj-$(CONFIG_PHY_MESON_G12A_USB2)	+= phy-meson-g12a-usb2.o
 obj-$(CONFIG_PHY_MESON_GXL_USB3)	+= phy-meson-gxl-usb3.o
+obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE)	+= phy-meson-g12a-usb3-pcie.o
drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c new file +413 -0

413 lines not on this page · raw message

#9 lore raw

PATCH v3 7/8 usb: dwc2: Add Amlogic G12A DWC2 Params

In reply to Neil Armstrong

This patchs sets the params for the DWC2 Controller found in the Amlogic G12A SoC family.

It mainly sets the settings reported incorrect by the driver, leaving the remaining detected automatically by the driver and provided by the DT node.

---
 drivers/usb/dwc2/params.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)
drivers/usb/dwc2/params.c +12 -0
index 24ff5f21cb25..442113246cba 100644
@@ -121,6 +121,16 @@ static void dwc2_set_amlogic_params(struct dwc2_hsotg *hsotg)
 	p->power_down = DWC2_POWER_DOWN_PARAM_NONE;
 }
 
+static void dwc2_set_amlogic_g12a_params(struct dwc2_hsotg *hsotg)
+{
+	struct dwc2_core_params *p = &hsotg->params;
+
+	p->lpm = false;
+	p->lpm_clock_gating = false;
+	p->besl = false;
+	p->hird_threshold_en = false;
+}
+
 static void dwc2_set_amcc_params(struct dwc2_hsotg *hsotg)
 {
 	struct dwc2_core_params *p = &hsotg->params;
@@ -167,6 +177,8 @@ const struct of_device_id dwc2_of_match_table[] = {
 	  .data = dwc2_set_amlogic_params },
 	{ .compatible = "amlogic,meson-gxbb-usb",
 	  .data = dwc2_set_amlogic_params },
+	{ .compatible = "amlogic,meson-g12a-usb",
+	  .data = dwc2_set_amlogic_g12a_params },
 	{ .compatible = "amcc,dwc-otg", .data = dwc2_set_amcc_params },
 	{ .compatible = "st,stm32f4x9-fsotg",
 	  .data = dwc2_set_stm32f4x9_fsotg_params },
#10 lore raw

PATCH v3 8/8 usb: dwc3: Add Amlogic G12A DWC3 glue

In reply to Neil Armstrong

Adds support for Amlogic G12A USB Control Glue HW.

The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only

A glue connects these both controllers to 2 USB2 PHYs, and optionnally to an USB3+PCIE Combo PHY shared with the PCIE controller.

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY.

This drivers supports the on-probe setup of the OTG mode, and manually via a debugfs interface. The IRQ mode change detect is yet to be added in a future patchset, mainly due to lack of hardware to validate on.

---
 drivers/usb/dwc3/Kconfig           |  10 +
 drivers/usb/dwc3/Makefile          |   1 +
 drivers/usb/dwc3/dwc3-meson-g12a.c | 602 +++++++++++++++++++++++++++++
 3 files changed, 613 insertions(+)
 create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c
drivers/usb/dwc3/Kconfig +10 -0
index 2b1494460d0c..d2ea9670563c 100644
@@ -95,6 +95,16 @@ config USB_DWC3_KEYSTONE
 	  Support of USB2/3 functionality in TI Keystone2 and AM654 platforms.
 	  Say 'Y' or 'M' here if you have one such device
 
+config USB_DWC3_MESON_G12A
+       tristate "Amlogic Meson G12A Platforms"
+       depends on OF && COMMON_CLK
+       depends on ARCH_MESON || COMPILE_TEST
+       default USB_DWC3
+       select USB_ROLE_SWITCH
+       help
+         Support USB2/3 functionality in Amlogic G12A platforms.
+	 Say 'Y' or 'M' if you have one such device.
+
 config USB_DWC3_OF_SIMPLE
        tristate "Generic OF Simple Glue Layer"
        depends on OF && COMMON_CLK
drivers/usb/dwc3/Makefile +1 -0
index 6e3ef6144e5d..ae86da0dc5bd 100644
@@ -47,6 +47,7 @@ obj-$(CONFIG_USB_DWC3_EXYNOS)		+= dwc3-exynos.o
 obj-$(CONFIG_USB_DWC3_PCI)		+= dwc3-pci.o
 obj-$(CONFIG_USB_DWC3_HAPS)		+= dwc3-haps.o
 obj-$(CONFIG_USB_DWC3_KEYSTONE)		+= dwc3-keystone.o
+obj-$(CONFIG_USB_DWC3_MESON_G12A)	+= dwc3-meson-g12a.o
 obj-$(CONFIG_USB_DWC3_OF_SIMPLE)	+= dwc3-of-simple.o
 obj-$(CONFIG_USB_DWC3_ST)		+= dwc3-st.o
 obj-$(CONFIG_USB_DWC3_QCOM)		+= dwc3-qcom.o
drivers/usb/dwc3/dwc3-meson-g12a.c new file +602 -0

602 lines not on this page · raw message

#11 lore raw

Re: [PATCH v3 8/8] usb: dwc3: Add Amlogic G12A DWC3 glue

Hi Neil,

Quoted 512 lines · Neil Armstrong

Adds support for Amlogic G12A USB Control Glue HW.

The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only

A glue connects these both controllers to 2 USB2 PHYs, and optionnally to an USB3+PCIE Combo PHY shared with the PCIE controller.

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY.

This drivers supports the on-probe setup of the OTG mode, and manually via a debugfs interface. The IRQ mode change detect is yet to be added in a future patchset, mainly due to lack of hardware to validate on.

---
 drivers/usb/dwc3/Kconfig           |  10 +
 drivers/usb/dwc3/Makefile          |   1 +
 drivers/usb/dwc3/dwc3-meson-g12a.c | 602 +++++++++++++++++++++++++++++
 3 files changed, 613 insertions(+)
 create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c
drivers/usb/dwc3/Kconfig +10 -0
index 2b1494460d0c..d2ea9670563c 100644
@@ -95,6 +95,16 @@ config USB_DWC3_KEYSTONE
 	  Support of USB2/3 functionality in TI Keystone2 and AM654 platforms.
 	  Say 'Y' or 'M' here if you have one such device
 
+config USB_DWC3_MESON_G12A
+       tristate "Amlogic Meson G12A Platforms"
+       depends on OF && COMMON_CLK
+       depends on ARCH_MESON || COMPILE_TEST
+       default USB_DWC3
+       select USB_ROLE_SWITCH
+       help
+         Support USB2/3 functionality in Amlogic G12A platforms.
+	 Say 'Y' or 'M' if you have one such device.
+
 config USB_DWC3_OF_SIMPLE
        tristate "Generic OF Simple Glue Layer"
        depends on OF && COMMON_CLK
drivers/usb/dwc3/Makefile +1 -0
index 6e3ef6144e5d..ae86da0dc5bd 100644
@@ -47,6 +47,7 @@ obj-$(CONFIG_USB_DWC3_EXYNOS)		+= dwc3-exynos.o
 obj-$(CONFIG_USB_DWC3_PCI)		+= dwc3-pci.o
 obj-$(CONFIG_USB_DWC3_HAPS)		+= dwc3-haps.o
 obj-$(CONFIG_USB_DWC3_KEYSTONE)		+= dwc3-keystone.o
+obj-$(CONFIG_USB_DWC3_MESON_G12A)	+= dwc3-meson-g12a.o
 obj-$(CONFIG_USB_DWC3_OF_SIMPLE)	+= dwc3-of-simple.o
 obj-$(CONFIG_USB_DWC3_ST)		+= dwc3-st.o
 obj-$(CONFIG_USB_DWC3_QCOM)		+= dwc3-qcom.o
drivers/usb/dwc3/dwc3-meson-g12a.c new file +448 -0
new file mode 100644
index 000000000000..9f4554e8e6e7
@@ -0,0 +1,602 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * USB Glue for Amlogic G12A SoCs
+ *
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <[email protected]>
+ */
+
+/*
+ * The USB is organized with a glue around the DWC3 Controller IP as :
+ * - Control registers for each USB2 Ports
+ * - Control registers for the USB PHY layer
+ * - SuperSpeed PHY can be enabled only if port is used
+ *
+ * TOFIX:
+ * - Add dynamic OTG switching with ID change interrupt
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/reset.h>
+#include <linux/phy/phy.h>
+#include <linux/usb/otg.h>
+#include <linux/usb/role.h>
+#include <linux/regulator/consumer.h>
+
+/* USB2 Ports Control Registers */
+
+#define U2P_REG_SIZE						0x20
+
+#define U2P_R0							0x0
+	#define U2P_R0_HOST_DEVICE				BIT(0)
+	#define U2P_R0_POWER_OK					BIT(1)
+	#define U2P_R0_HAST_MODE				BIT(2)
+	#define U2P_R0_POWER_ON_RESET				BIT(3)
+	#define U2P_R0_ID_PULLUP				BIT(4)
+	#define U2P_R0_DRV_VBUS					BIT(5)
+
+#define U2P_R1							0x4
+	#define U2P_R1_PHY_READY				BIT(0)
+	#define U2P_R1_ID_DIG					BIT(1)
+	#define U2P_R1_OTG_SESSION_VALID			BIT(2)
+	#define U2P_R1_VBUS_VALID				BIT(3)
+
+/* USB Glue Control Registers */
+
+#define USB_R0							0x80
+	#define USB_R0_P30_LANE0_TX2RX_LOOPBACK			BIT(17)
+	#define USB_R0_P30_LANE0_EXT_PCLK_REQ			BIT(18)
+	#define USB_R0_P30_PCS_RX_LOS_MASK_VAL_MASK		GENMASK(28, 19)
+	#define USB_R0_U2D_SS_SCALEDOWN_MODE_MASK		GENMASK(30, 29)
+	#define USB_R0_U2D_ACT					BIT(31)
+
+#define USB_R1							0x84
+	#define USB_R1_U3H_BIGENDIAN_GS				BIT(0)
+	#define USB_R1_U3H_PME_ENABLE				BIT(1)
+	#define USB_R1_U3H_HUB_PORT_OVERCURRENT_MASK		GENMASK(4, 2)
+	#define USB_R1_U3H_HUB_PORT_PERM_ATTACH_MASK		GENMASK(9, 7)
+	#define USB_R1_U3H_HOST_U2_PORT_DISABLE_MASK		GENMASK(13, 12)
+	#define USB_R1_U3H_HOST_U3_PORT_DISABLE			BIT(16)
+	#define USB_R1_U3H_HOST_PORT_POWER_CONTROL_PRESENT	BIT(17)
+	#define USB_R1_U3H_HOST_MSI_ENABLE			BIT(18)
+	#define USB_R1_U3H_FLADJ_30MHZ_REG_MASK			GENMASK(24, 19)
+	#define USB_R1_P30_PCS_TX_SWING_FULL_MASK		GENMASK(31, 25)
+
+#define USB_R2							0x88
+	#define USB_R2_P30_PCS_TX_DEEMPH_3P5DB_MASK		GENMASK(25, 20)
+	#define USB_R2_P30_PCS_TX_DEEMPH_6DB_MASK		GENMASK(31, 26)
+
+#define USB_R3							0x8c
+	#define USB_R3_P30_SSC_ENABLE				BIT(0)
+	#define USB_R3_P30_SSC_RANGE_MASK			GENMASK(3, 1)
+	#define USB_R3_P30_SSC_REF_CLK_SEL_MASK			GENMASK(12, 4)
+	#define USB_R3_P30_REF_SSP_EN				BIT(13)
+
+#define USB_R4							0x90
+	#define USB_R4_P21_PORT_RESET_0				BIT(0)
+	#define USB_R4_P21_SLEEP_M0				BIT(1)
+	#define USB_R4_MEM_PD_MASK				GENMASK(3, 2)
+	#define USB_R4_P21_ONLY					BIT(4)
+
+#define USB_R5							0x94
+	#define USB_R5_ID_DIG_SYNC				BIT(0)
+	#define USB_R5_ID_DIG_REG				BIT(1)
+	#define USB_R5_ID_DIG_CFG_MASK				GENMASK(3, 2)
+	#define USB_R5_ID_DIG_EN_0				BIT(4)
+	#define USB_R5_ID_DIG_EN_1				BIT(5)
+	#define USB_R5_ID_DIG_CURR				BIT(6)
+	#define USB_R5_ID_DIG_IRQ				BIT(7)
+	#define USB_R5_ID_DIG_TH_MASK				GENMASK(15, 8)
+	#define USB_R5_ID_DIG_CNT_MASK				GENMASK(23, 16)
+
+enum {
+	USB2_HOST_PHY = 0,
+	USB2_OTG_PHY,
+	USB3_HOST_PHY,
+	PHY_COUNT,
+};
+
+static const char *phy_names[PHY_COUNT] = {
+	"usb2-phy0", "usb2-phy1", "usb3-phy0",
+};
+
+struct dwc3_meson_g12a {
+	struct device		*dev;
+	struct regmap		*regmap;
+	struct clk		*clk;
+	struct reset_control	*reset;
+	struct phy		*phys[PHY_COUNT];
+	enum usb_dr_mode	otg_mode;
+	enum phy_mode		otg_phy_mode;
+	unsigned int		usb2_ports;
+	unsigned int		usb3_ports;
+	struct regulator	*vbus;
+	struct usb_role_switch_desc switch_desc;
+	struct usb_role_switch	*role_switch;
+};
+
+static void dwc3_meson_g12a_usb2_set_mode(struct dwc3_meson_g12a *priv,
+					  int i, enum phy_mode mode)
+{
+	if (mode == PHY_MODE_USB_HOST)
+		regmap_update_bits(priv->regmap, U2P_R0 + (U2P_REG_SIZE * i),
+				U2P_R0_HOST_DEVICE,
+				U2P_R0_HOST_DEVICE);
+	else
+		regmap_update_bits(priv->regmap, U2P_R0 + (U2P_REG_SIZE * i),
+				U2P_R0_HOST_DEVICE, 0);
+}
+
+static int dwc3_meson_g12a_usb2_init(struct dwc3_meson_g12a *priv)
+{
+	int i;
+
+	if (priv->otg_mode == USB_DR_MODE_PERIPHERAL)
+		priv->otg_phy_mode = PHY_MODE_USB_DEVICE;
+	else
+		priv->otg_phy_mode = PHY_MODE_USB_HOST;
+
+	for (i = 0 ; i < USB3_HOST_PHY ; ++i) {
+		if (!priv->phys[i])
+			continue;
+
+		regmap_update_bits(priv->regmap, U2P_R0 + (U2P_REG_SIZE * i),
+				   U2P_R0_POWER_ON_RESET,
+				   U2P_R0_POWER_ON_RESET);
+
+		if (i == USB2_OTG_PHY) {
+			regmap_update_bits(priv->regmap,
+				U2P_R0 + (U2P_REG_SIZE * i),
+				U2P_R0_ID_PULLUP | U2P_R0_DRV_VBUS,
+				U2P_R0_ID_PULLUP | U2P_R0_DRV_VBUS);
+
+			dwc3_meson_g12a_usb2_set_mode(priv, i,
+						      priv->otg_phy_mode);
+		} else
+			dwc3_meson_g12a_usb2_set_mode(priv, i,
+						      PHY_MODE_USB_HOST);
+
+		regmap_update_bits(priv->regmap, U2P_R0 + (U2P_REG_SIZE * i),
+				   U2P_R0_POWER_ON_RESET, 0);
+	}
+
+	return 0;
+}
+
+static void dwc3_meson_g12a_usb3_init(struct dwc3_meson_g12a *priv)
+{
+	regmap_update_bits(priv->regmap, USB_R3,
+			USB_R3_P30_SSC_RANGE_MASK |
+			USB_R3_P30_REF_SSP_EN,
+			USB_R3_P30_SSC_ENABLE |
+			FIELD_PREP(USB_R3_P30_SSC_RANGE_MASK, 2) |
+			USB_R3_P30_REF_SSP_EN);
+	udelay(2);
+
+	regmap_update_bits(priv->regmap, USB_R2,
+			USB_R2_P30_PCS_TX_DEEMPH_3P5DB_MASK,
+			FIELD_PREP(USB_R2_P30_PCS_TX_DEEMPH_3P5DB_MASK, 0x15));
+
+	regmap_update_bits(priv->regmap, USB_R2,
+			USB_R2_P30_PCS_TX_DEEMPH_6DB_MASK,
+			FIELD_PREP(USB_R2_P30_PCS_TX_DEEMPH_6DB_MASK, 0x20));
+
+	udelay(2);
+
+	regmap_update_bits(priv->regmap, USB_R1,
+			USB_R1_U3H_HOST_PORT_POWER_CONTROL_PRESENT,
+			USB_R1_U3H_HOST_PORT_POWER_CONTROL_PRESENT);
+
+	regmap_update_bits(priv->regmap, USB_R1,
+			USB_R1_P30_PCS_TX_SWING_FULL_MASK,
+			FIELD_PREP(USB_R1_P30_PCS_TX_SWING_FULL_MASK, 127));
+}
+
+static void dwc3_meson_g12a_usb_otg_apply_mode(struct dwc3_meson_g12a *priv)
+{
+	if (priv->otg_phy_mode == PHY_MODE_USB_DEVICE) {
+		regmap_update_bits(priv->regmap, USB_R0,
+				USB_R0_U2D_ACT, USB_R0_U2D_ACT);
+		regmap_update_bits(priv->regmap, USB_R0,
+				USB_R0_U2D_SS_SCALEDOWN_MODE_MASK, 0);
+		regmap_update_bits(priv->regmap, USB_R4,
+				USB_R4_P21_SLEEP_M0, USB_R4_P21_SLEEP_M0);
+	} else {
+		regmap_update_bits(priv->regmap, USB_R0,
+				USB_R0_U2D_ACT, 0);
+		regmap_update_bits(priv->regmap, USB_R4,
+				USB_R4_P21_SLEEP_M0, 0);
+	}
+}
+
+static int dwc3_meson_g12a_usb_init(struct dwc3_meson_g12a *priv)
+{
+	int ret;
+
+	ret = dwc3_meson_g12a_usb2_init(priv);
+	if (ret)
+		return ret;
+
+	regmap_update_bits(priv->regmap, USB_R1,
+			USB_R1_U3H_FLADJ_30MHZ_REG_MASK,
+			FIELD_PREP(USB_R1_U3H_FLADJ_30MHZ_REG_MASK, 0x20));
+
+	regmap_update_bits(priv->regmap, USB_R5,
+			USB_R5_ID_DIG_EN_0,
+			USB_R5_ID_DIG_EN_0);
+	regmap_update_bits(priv->regmap, USB_R5,
+			USB_R5_ID_DIG_EN_1,
+			USB_R5_ID_DIG_EN_1);
+	regmap_update_bits(priv->regmap, USB_R5,
+			USB_R5_ID_DIG_TH_MASK,
+			FIELD_PREP(USB_R5_ID_DIG_TH_MASK, 0xff));
+
+	/* If we have an actual SuperSpeed port, initialize it */
+	if (priv->usb3_ports)
+		dwc3_meson_g12a_usb3_init(priv);
+
+	dwc3_meson_g12a_usb_otg_apply_mode(priv);
+
+	return 0;
+}
+
+static const struct regmap_config phy_meson_g12a_usb3_regmap_conf = {
+	.reg_bits = 8,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = USB_R5,
+};
+
+static int dwc3_meson_g12a_get_phys(struct dwc3_meson_g12a *priv)
+{
+	int i;
+
+	for (i = 0 ; i < PHY_COUNT ; ++i) {
+		priv->phys[i] = devm_phy_optional_get(priv->dev, phy_names[i]);
+		if (!priv->phys[i])
+			continue;
+
+		if (IS_ERR(priv->phys[i]))
+			return PTR_ERR(priv->phys[i]);
+
+		if (i == USB3_HOST_PHY)
+			priv->usb3_ports++;
+		else
+			priv->usb2_ports++;
+	}
+
+	dev_info(priv->dev, "USB2 ports: %d\n", priv->usb2_ports);
+	dev_info(priv->dev, "USB3 ports: %d\n", priv->usb3_ports);
+
+	return 0;
+}
+
+static enum phy_mode dwc3_meson_g12a_get_id(struct dwc3_meson_g12a *priv)
+{
+	u32 reg;
+
+	regmap_read(priv->regmap, USB_R5, &reg);
+
+	if (reg & (USB_R5_ID_DIG_SYNC | USB_R5_ID_DIG_REG))
+		return PHY_MODE_USB_DEVICE;
+
+	return PHY_MODE_USB_HOST;
+}
+
+static int dwc3_meson_g12a_otg_mode_set(struct dwc3_meson_g12a *priv,
+					enum phy_mode mode)
+{
+	int ret;
+
+	if (!priv->phys[USB2_OTG_PHY])
+		return -EINVAL;
+
+	if (mode == PHY_MODE_USB_HOST)
+		dev_info(priv->dev, "switching to Host Mode\n");
+	else
+		dev_info(priv->dev, "switching to Device Mode\n");
+
+	if (priv->vbus) {
+		if (mode == PHY_MODE_USB_DEVICE)
+			ret = regulator_disable(priv->vbus);
+		else
+			ret = regulator_enable(priv->vbus);
+		if (ret)
+			return ret;
+	}
+
+	priv->otg_phy_mode = mode;
+
+	dwc3_meson_g12a_usb2_set_mode(priv, USB2_OTG_PHY, mode);
+
+	dwc3_meson_g12a_usb_otg_apply_mode(priv);
+
+	return 0;
+}
+
+static int dwc3_meson_g12a_role_set(struct device *dev, enum usb_role role)
+{
+	struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
+	enum phy_mode mode;
+
+	if (role == USB_ROLE_NONE)
+		return 0;
+
+	mode = (role == USB_ROLE_HOST) ? PHY_MODE_USB_HOST
+				       : PHY_MODE_USB_DEVICE;
+
+	if (mode == priv->otg_phy_mode)
+		return 0;
+
+	return dwc3_meson_g12a_otg_mode_set(priv, mode);
+}
+
+static enum usb_role dwc3_meson_g12a_role_get(struct device *dev)
+{
+	struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
+
+	return priv->otg_phy_mode == PHY_MODE_USB_HOST ?
+		USB_ROLE_HOST : USB_ROLE_DEVICE;
+}
+
+static struct device *dwc3_meson_g12_find_child(struct device *dev,
+						const char *compatible)
+{
+	struct platform_device *pdev;
+	struct device_node *np;
+
+	np = of_get_compatible_child(dev->of_node, compatible);
+	if (!np)
+		return NULL;
+
+	pdev = of_find_device_by_node(np);
+	of_node_put(np);
+	if (!pdev)
+		return NULL;
+
+	return &pdev->dev;
+}
+
+static int dwc3_meson_g12a_probe(struct platform_device *pdev)
+{
+	struct dwc3_meson_g12a	*priv;
+	struct device		*dev = &pdev->dev;
+	struct device_node	*np = dev->of_node;
+	void __iomem *base;
+	struct resource *res;
+	enum phy_mode otg_id;
+	int ret, i;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	priv->regmap = devm_regmap_init_mmio(dev, base,
+					     &phy_meson_g12a_usb3_regmap_conf);
+	if (IS_ERR(priv->regmap))
+		return PTR_ERR(priv->regmap);
+
+	priv->vbus = devm_regulator_get_optional(dev, "vbus");
+	if (IS_ERR(priv->vbus)) {
+		if (PTR_ERR(priv->vbus) == -EPROBE_DEFER)
+			return PTR_ERR(priv->vbus);
+		priv->vbus = NULL;
+	}
+
+	priv->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(priv->clk))
+		return PTR_ERR(priv->clk);
+
+	ret = clk_prepare_enable(priv->clk);
+	if (ret)
+		return ret;
+
+	devm_add_action_or_reset(dev,
+				 (void(*)(void *))clk_disable_unprepare,
+				 priv->clk);
+
+	platform_set_drvdata(pdev, priv);
+	priv->dev = dev;
+
+	priv->reset = devm_reset_control_get(dev, NULL);
+	if (IS_ERR(priv->reset)) {
+		ret = PTR_ERR(priv->reset);
+		dev_err(dev, "failed to get device reset, err=%d\n", ret);
+		return ret;
+	}
+
+	ret = reset_control_reset(priv->reset);
+	if (ret)
+		return ret;
+
+	ret = dwc3_meson_g12a_get_phys(priv);
+	if (ret)
+		return ret;
+
+	if (priv->vbus) {
+		ret = regulator_enable(priv->vbus);
+		if (ret)
+			return ret;
+	}
+
+	/* Get dr_mode */
+	priv->otg_mode = usb_get_dr_mode(dev);
+
+	dwc3_meson_g12a_usb_init(priv);
+
+	/* Init PHYs */
+	for (i = 0 ; i < PHY_COUNT ; ++i) {
+		ret = phy_init(priv->phys[i]);
+		if (ret)
+			goto err_phys_power;
+	}
+
+	/* Set PHY Power */

drivers/usb/dwc3/dwc3-meson-g12a.c line 458

Quoted 10 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +10 -0
+	for (i = 0 ; i < PHY_COUNT ; ++i) {
+		ret = phy_power_on(priv->phys[i]);
+		if (ret)
+			goto err_phys_put;
+	}
+
+	ret = of_platform_populate(np, NULL, NULL, dev);
+	if (ret) {
+		clk_disable_unprepare(priv->clk);
+		clk_put(priv->clk);

No need clk_put()

Quoted 33 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +33 -0
+
+		goto err_phys_exit;
+	}
+
+	/* Setup OTG mode corresponding to the ID pin */
+	if (priv->otg_mode == USB_DR_MODE_OTG) {
+		/* TOFIX Handle ID mode toggling via IRQ */
+		otg_id = dwc3_meson_g12a_get_id(priv);
+		if (otg_id != priv->otg_phy_mode) {
+			if (dwc3_meson_g12a_otg_mode_set(priv, otg_id))
+				dev_warn(dev, "Failed to switch OTG mode\n");
+		}
+	}
+
+	/* Setup role switcher */
+	priv->switch_desc.usb2_port = dwc3_meson_g12_find_child(dev,
+								"snps,dwc3");
+	priv->switch_desc.udc = dwc3_meson_g12_find_child(dev, "snps,dwc2");
+	priv->switch_desc.allow_userspace_control = true;
+	priv->switch_desc.set = dwc3_meson_g12a_role_set;
+	priv->switch_desc.get = dwc3_meson_g12a_role_get;
+
+	priv->role_switch = usb_role_switch_register(dev, &priv->switch_desc);
+	if (IS_ERR(priv->role_switch))
+		dev_warn(dev, "Unable to register Role Switch\n");
+
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+	pm_runtime_get_sync(dev);
+
+	return 0;
+
+err_phys_exit:

drivers/usb/dwc3/dwc3-meson-g12a.c line 501

Quoted 10 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +10 -0
+	for (i = 0 ; i < PHY_COUNT ; ++i)
+		phy_exit(priv->phys[i]);
+
+err_phys_power:
+	for (i = 0 ; i < PHY_COUNT ; ++i)
+		phy_power_off(priv->phys[i]);
+
+err_phys_put:
+	for (i = 0 ; i < PHY_COUNT ; ++i)
+		phy_put(priv->phys[i]);

you get phy by devm_phy_optional_get(), no need call phy_put(),

Quoted 8 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +8 -0
+
+	return ret;
+}
+
+static int dwc3_meson_g12a_remove(struct platform_device *pdev)
+{
+	struct dwc3_meson_g12a *priv = platform_get_drvdata(pdev);
+	struct device *dev = &pdev->dev;

drivers/usb/dwc3/dwc3-meson-g12a.c line 519

Quoted 10 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +10 -0
+	int i;
+
+	usb_role_switch_unregister(priv->role_switch);
+
+	of_platform_depopulate(dev);
+
+	for (i = 0 ; i < PHY_COUNT ; ++i) {
+		phy_power_off(priv->phys[i]);
+		phy_exit(priv->phys[i]);
+		phy_put(priv->phys[i]);

here, and remove others if have.

Quoted 43 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +43 -0
+	}
+
+	pm_runtime_disable(dev);
+	pm_runtime_put_noidle(dev);
+	pm_runtime_set_suspended(dev);
+
+	return 0;
+}
+
+static int __maybe_unused dwc3_meson_g12a_runtime_suspend(struct device *dev)
+{
+	struct dwc3_meson_g12a	*priv = dev_get_drvdata(dev);
+
+	clk_disable(priv->clk);
+
+	return 0;
+}
+
+static int __maybe_unused dwc3_meson_g12a_runtime_resume(struct device *dev)
+{
+	struct dwc3_meson_g12a	*priv = dev_get_drvdata(dev);
+
+	return clk_enable(priv->clk);
+}
+
+static int __maybe_unused dwc3_meson_g12a_suspend(struct device *dev)
+{
+	struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
+	int i;
+
+	for (i = 0 ; i < PHY_COUNT ; ++i)
+		phy_exit(priv->phys[i]);
+
+	reset_control_assert(priv->reset);
+
+	return 0;
+}
+
+static int __maybe_unused dwc3_meson_g12a_resume(struct device *dev)
+{
+	struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
+	int i, ret;
+

drivers/usb/dwc3/dwc3-meson-g12a.c line 572

Quoted 10 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +10 -0
+	reset_control_deassert(priv->reset);
+
+	dwc3_meson_g12a_usb_init(priv);
+
+	/* Init PHYs */
+	for (i = 0 ; i < PHY_COUNT ; ++i) {
+		ret = phy_init(priv->phys[i]);
+		if (ret)
+			return ret;
+	}

Do you need power on phys?

Quoted 30 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +30 -0
+
+	return 0;
+}
+
+static const struct dev_pm_ops dwc3_meson_g12a_dev_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(dwc3_meson_g12a_suspend, dwc3_meson_g12a_resume)
+	SET_RUNTIME_PM_OPS(dwc3_meson_g12a_runtime_suspend,
+			dwc3_meson_g12a_runtime_resume, NULL)
+};
+
+static const struct of_device_id dwc3_meson_g12a_match[] = {
+	{ .compatible = "amlogic,meson-g12a-usb-ctrl" },
+	{ /* Sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, dwc3_meson_g12a_match);
+
+static struct platform_driver dwc3_meson_g12a_driver = {
+	.probe		= dwc3_meson_g12a_probe,
+	.remove		= dwc3_meson_g12a_remove,
+	.driver		= {
+		.name	= "dwc3-meson-g12a",
+		.of_match_table = dwc3_meson_g12a_match,
+		.pm	= &dwc3_meson_g12a_dev_pm_ops,
+	},
+};
+
+module_platform_driver(dwc3_meson_g12a_driver);
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Amlogic Meson G12A USB Glue Layer");
+MODULE_AUTHOR("Neil Armstrong <[email protected]>");
#12 lore raw

Re: [PATCH v3 8/8] usb: dwc3: Add Amlogic G12A DWC3 glue

Hi,

Quoted 84 lines · Chunfeng Yun

Hi Neil,

Quoted 82 lines · Neil Armstrong

Adds support for Amlogic G12A USB Control Glue HW.

The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only

A glue connects these both controllers to 2 USB2 PHYs, and optionnally to an USB3+PCIE Combo PHY shared with the PCIE controller.

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY.

This drivers supports the on-probe setup of the OTG mode, and manually via a debugfs interface. The IRQ mode change detect is yet to be added in a future patchset, mainly due to lack of hardware to validate on.

---
 drivers/usb/dwc3/Kconfig           |  10 +
 drivers/usb/dwc3/Makefile          |   1 +
 drivers/usb/dwc3/dwc3-meson-g12a.c | 602 +++++++++++++++++++++++++++++
 3 files changed, 613 insertions(+)
 create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c
drivers/usb/dwc3/Kconfig +10 -0
index 2b1494460d0c..d2ea9670563c 100644
@@ -95,6 +95,16 @@ config USB_DWC3_KEYSTONE
 	  Support of USB2/3 functionality in TI Keystone2 and AM654 platforms.
 	  Say 'Y' or 'M' here if you have one such device
 
+config USB_DWC3_MESON_G12A
+       tristate "Amlogic Meson G12A Platforms"
+       depends on OF && COMMON_CLK
+       depends on ARCH_MESON || COMPILE_TEST
+       default USB_DWC3
+       select USB_ROLE_SWITCH
+       help
+         Support USB2/3 functionality in Amlogic G12A platforms.
+	 Say 'Y' or 'M' if you have one such device.
+
 config USB_DWC3_OF_SIMPLE
        tristate "Generic OF Simple Glue Layer"
        depends on OF && COMMON_CLK
drivers/usb/dwc3/Makefile +1 -0
index 6e3ef6144e5d..ae86da0dc5bd 100644
@@ -47,6 +47,7 @@ obj-$(CONFIG_USB_DWC3_EXYNOS)		+= dwc3-exynos.o
 obj-$(CONFIG_USB_DWC3_PCI)		+= dwc3-pci.o
 obj-$(CONFIG_USB_DWC3_HAPS)		+= dwc3-haps.o
 obj-$(CONFIG_USB_DWC3_KEYSTONE)		+= dwc3-keystone.o
+obj-$(CONFIG_USB_DWC3_MESON_G12A)	+= dwc3-meson-g12a.o
 obj-$(CONFIG_USB_DWC3_OF_SIMPLE)	+= dwc3-of-simple.o
 obj-$(CONFIG_USB_DWC3_ST)		+= dwc3-st.o
 obj-$(CONFIG_USB_DWC3_QCOM)		+= dwc3-qcom.o
drivers/usb/dwc3/dwc3-meson-g12a.c new file +18 -0
new file mode 100644
index 000000000000..9f4554e8e6e7
@@ -0,0 +1,602 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * USB Glue for Amlogic G12A SoCs
+ *
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <[email protected]>
+ */
+
+/*
+ * The USB is organized with a glue around the DWC3 Controller IP as :
+ * - Control registers for each USB2 Ports
+ * - Control registers for the USB PHY layer
+ * - SuperSpeed PHY can be enabled only if port is used
+ *
+ * TOFIX:
+ * - Add dynamic OTG switching with ID change interrupt
+ */
+

[..]

Quoted 6 lines

drivers/usb/dwc3/dwc3-meson-g12a.c line 458

Quoted 5 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +5 -0
+
+	ret = of_platform_populate(np, NULL, NULL, dev);
+	if (ret) {
+		clk_disable_unprepare(priv->clk);
+		clk_put(priv->clk);

No need clk_put()

Exact

Quoted 36 lines
Quoted 36 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +36 -0
+
+		goto err_phys_exit;
+	}
+
+	/* Setup OTG mode corresponding to the ID pin */
+	if (priv->otg_mode == USB_DR_MODE_OTG) {
+		/* TOFIX Handle ID mode toggling via IRQ */
+		otg_id = dwc3_meson_g12a_get_id(priv);
+		if (otg_id != priv->otg_phy_mode) {
+			if (dwc3_meson_g12a_otg_mode_set(priv, otg_id))
+				dev_warn(dev, "Failed to switch OTG mode\n");
+		}
+	}
+
+	/* Setup role switcher */
+	priv->switch_desc.usb2_port = dwc3_meson_g12_find_child(dev,
+								"snps,dwc3");
+	priv->switch_desc.udc = dwc3_meson_g12_find_child(dev, "snps,dwc2");
+	priv->switch_desc.allow_userspace_control = true;
+	priv->switch_desc.set = dwc3_meson_g12a_role_set;
+	priv->switch_desc.get = dwc3_meson_g12a_role_get;
+
+	priv->role_switch = usb_role_switch_register(dev, &priv->switch_desc);
+	if (IS_ERR(priv->role_switch))
+		dev_warn(dev, "Unable to register Role Switch\n");
+
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+	pm_runtime_get_sync(dev);
+
+	return 0;
+
+err_phys_exit:
+	for (i = 0 ; i < PHY_COUNT ; ++i)
+		phy_exit(priv->phys[i]);
+
Quoted 8 lines

drivers/usb/dwc3/dwc3-meson-g12a.c line 501

Quoted 7 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +7 -0
+err_phys_power:
+	for (i = 0 ; i < PHY_COUNT ; ++i)
+		phy_power_off(priv->phys[i]);
+
+err_phys_put:
+	for (i = 0 ; i < PHY_COUNT ; ++i)
+		phy_put(priv->phys[i]);

you get phy by devm_phy_optional_get(), no need call phy_put(),

Indeed, also forgot these

Quoted 11 lines
Quoted 11 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +11 -0
+
+	return ret;
+}
+
+static int dwc3_meson_g12a_remove(struct platform_device *pdev)
+{
+	struct dwc3_meson_g12a *priv = platform_get_drvdata(pdev);
+	struct device *dev = &pdev->dev;
+	int i;
+
+	usb_role_switch_unregister(priv->role_switch);
Quoted 8 lines

drivers/usb/dwc3/dwc3-meson-g12a.c line 519

Quoted 7 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +7 -0
+
+	of_platform_depopulate(dev);
+
+	for (i = 0 ; i < PHY_COUNT ; ++i) {
+		phy_power_off(priv->phys[i]);
+		phy_exit(priv->phys[i]);
+		phy_put(priv->phys[i]);

here, and remove others if have.

This is the last one I hope

Quoted 46 lines
Quoted 46 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +46 -0
+	}
+
+	pm_runtime_disable(dev);
+	pm_runtime_put_noidle(dev);
+	pm_runtime_set_suspended(dev);
+
+	return 0;
+}
+
+static int __maybe_unused dwc3_meson_g12a_runtime_suspend(struct device *dev)
+{
+	struct dwc3_meson_g12a	*priv = dev_get_drvdata(dev);
+
+	clk_disable(priv->clk);
+
+	return 0;
+}
+
+static int __maybe_unused dwc3_meson_g12a_runtime_resume(struct device *dev)
+{
+	struct dwc3_meson_g12a	*priv = dev_get_drvdata(dev);
+
+	return clk_enable(priv->clk);
+}
+
+static int __maybe_unused dwc3_meson_g12a_suspend(struct device *dev)
+{
+	struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
+	int i;
+
+	for (i = 0 ; i < PHY_COUNT ; ++i)
+		phy_exit(priv->phys[i]);
+
+	reset_control_assert(priv->reset);
+
+	return 0;
+}
+
+static int __maybe_unused dwc3_meson_g12a_resume(struct device *dev)
+{
+	struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
+	int i, ret;
+
+	reset_control_deassert(priv->reset);
+
+	dwc3_meson_g12a_usb_init(priv);
Quoted 8 lines

drivers/usb/dwc3/dwc3-meson-g12a.c line 504

Quoted 7 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +7 -0
+
+	/* Init PHYs */
+	for (i = 0 ; i < PHY_COUNT ; ++i) {
+		ret = phy_init(priv->phys[i]);
+		if (ret)
+			return ret;
+	}

Do you need power on phys?

Regulators can be tied to the PHYs, should I disable power on suspend aswell ?

Quoted 22 lines
Quoted 22 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +22 -0
+
+	return 0;
+}
+
+static const struct dev_pm_ops dwc3_meson_g12a_dev_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(dwc3_meson_g12a_suspend, dwc3_meson_g12a_resume)
+	SET_RUNTIME_PM_OPS(dwc3_meson_g12a_runtime_suspend,
+			dwc3_meson_g12a_runtime_resume, NULL)
+};
+
+static const struct of_device_id dwc3_meson_g12a_match[] = {
+	{ .compatible = "amlogic,meson-g12a-usb-ctrl" },
+	{ /* Sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, dwc3_meson_g12a_match);
+
+static struct platform_driver dwc3_meson_g12a_driver = {
+	.probe		= dwc3_meson_g12a_probe,
+	.remove		= dwc3_meson_g12a_remove,
+	.driver		= {
+		.name	= "dwc3-meson-g12a",
+		.of_match_table = dwc3_meson_g12a_match,
Quoted 10 lines

drivers/usb/dwc3/dwc3-meson-g12a.c line 602

Quoted 8 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +8 -0
+		.pm	= &dwc3_meson_g12a_dev_pm_ops,
+	},
+};
+
+module_platform_driver(dwc3_meson_g12a_driver);
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Amlogic Meson G12A USB Glue Layer");
+MODULE_AUTHOR("Neil Armstrong <[email protected]>");

Thanks,
Neil

#13 lore raw

Re: [PATCH v3 8/8] usb: dwc3: Add Amlogic G12A DWC3 glue

Hi,

Quoted 223 lines · Neil Armstrong

Hi,

Quoted 84 lines · Chunfeng Yun

Hi Neil,

Quoted 82 lines · Neil Armstrong

Adds support for Amlogic G12A USB Control Glue HW.

The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only

A glue connects these both controllers to 2 USB2 PHYs, and optionnally to an USB3+PCIE Combo PHY shared with the PCIE controller.

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY.

This drivers supports the on-probe setup of the OTG mode, and manually via a debugfs interface. The IRQ mode change detect is yet to be added in a future patchset, mainly due to lack of hardware to validate on.

---
 drivers/usb/dwc3/Kconfig           |  10 +
 drivers/usb/dwc3/Makefile          |   1 +
 drivers/usb/dwc3/dwc3-meson-g12a.c | 602 +++++++++++++++++++++++++++++
 3 files changed, 613 insertions(+)
 create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c
drivers/usb/dwc3/Kconfig +10 -0
index 2b1494460d0c..d2ea9670563c 100644
@@ -95,6 +95,16 @@ config USB_DWC3_KEYSTONE
 	  Support of USB2/3 functionality in TI Keystone2 and AM654 platforms.
 	  Say 'Y' or 'M' here if you have one such device
 
+config USB_DWC3_MESON_G12A
+       tristate "Amlogic Meson G12A Platforms"
+       depends on OF && COMMON_CLK
+       depends on ARCH_MESON || COMPILE_TEST
+       default USB_DWC3
+       select USB_ROLE_SWITCH
+       help
+         Support USB2/3 functionality in Amlogic G12A platforms.
+	 Say 'Y' or 'M' if you have one such device.
+
 config USB_DWC3_OF_SIMPLE
        tristate "Generic OF Simple Glue Layer"
        depends on OF && COMMON_CLK
drivers/usb/dwc3/Makefile +1 -0
index 6e3ef6144e5d..ae86da0dc5bd 100644
@@ -47,6 +47,7 @@ obj-$(CONFIG_USB_DWC3_EXYNOS)		+= dwc3-exynos.o
 obj-$(CONFIG_USB_DWC3_PCI)		+= dwc3-pci.o
 obj-$(CONFIG_USB_DWC3_HAPS)		+= dwc3-haps.o
 obj-$(CONFIG_USB_DWC3_KEYSTONE)		+= dwc3-keystone.o
+obj-$(CONFIG_USB_DWC3_MESON_G12A)	+= dwc3-meson-g12a.o
 obj-$(CONFIG_USB_DWC3_OF_SIMPLE)	+= dwc3-of-simple.o
 obj-$(CONFIG_USB_DWC3_ST)		+= dwc3-st.o
 obj-$(CONFIG_USB_DWC3_QCOM)		+= dwc3-qcom.o
drivers/usb/dwc3/dwc3-meson-g12a.c new file +18 -0
new file mode 100644
index 000000000000..9f4554e8e6e7
@@ -0,0 +1,602 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * USB Glue for Amlogic G12A SoCs
+ *
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <[email protected]>
+ */
+
+/*
+ * The USB is organized with a glue around the DWC3 Controller IP as :
+ * - Control registers for each USB2 Ports
+ * - Control registers for the USB PHY layer
+ * - SuperSpeed PHY can be enabled only if port is used
+ *
+ * TOFIX:
+ * - Add dynamic OTG switching with ID change interrupt
+ */
+

[..]

Quoted 6 lines

drivers/usb/dwc3/dwc3-meson-g12a.c line 458

Quoted 5 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +5 -0
+
+	ret = of_platform_populate(np, NULL, NULL, dev);
+	if (ret) {
+		clk_disable_unprepare(priv->clk);
+		clk_put(priv->clk);

No need clk_put()

Exact

Quoted 36 lines
Quoted 36 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +36 -0
+
+		goto err_phys_exit;
+	}
+
+	/* Setup OTG mode corresponding to the ID pin */
+	if (priv->otg_mode == USB_DR_MODE_OTG) {
+		/* TOFIX Handle ID mode toggling via IRQ */
+		otg_id = dwc3_meson_g12a_get_id(priv);
+		if (otg_id != priv->otg_phy_mode) {
+			if (dwc3_meson_g12a_otg_mode_set(priv, otg_id))
+				dev_warn(dev, "Failed to switch OTG mode\n");
+		}
+	}
+
+	/* Setup role switcher */
+	priv->switch_desc.usb2_port = dwc3_meson_g12_find_child(dev,
+								"snps,dwc3");
+	priv->switch_desc.udc = dwc3_meson_g12_find_child(dev, "snps,dwc2");
+	priv->switch_desc.allow_userspace_control = true;
+	priv->switch_desc.set = dwc3_meson_g12a_role_set;
+	priv->switch_desc.get = dwc3_meson_g12a_role_get;
+
+	priv->role_switch = usb_role_switch_register(dev, &priv->switch_desc);
+	if (IS_ERR(priv->role_switch))
+		dev_warn(dev, "Unable to register Role Switch\n");
+
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+	pm_runtime_get_sync(dev);
+
+	return 0;
+
+err_phys_exit:
+	for (i = 0 ; i < PHY_COUNT ; ++i)
+		phy_exit(priv->phys[i]);
+
Quoted 8 lines

drivers/usb/dwc3/dwc3-meson-g12a.c line 501

Quoted 7 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +7 -0
+err_phys_power:
+	for (i = 0 ; i < PHY_COUNT ; ++i)
+		phy_power_off(priv->phys[i]);
+
+err_phys_put:
+	for (i = 0 ; i < PHY_COUNT ; ++i)
+		phy_put(priv->phys[i]);

you get phy by devm_phy_optional_get(), no need call phy_put(),

Indeed, also forgot these

Quoted 11 lines
Quoted 11 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +11 -0
+
+	return ret;
+}
+
+static int dwc3_meson_g12a_remove(struct platform_device *pdev)
+{
+	struct dwc3_meson_g12a *priv = platform_get_drvdata(pdev);
+	struct device *dev = &pdev->dev;
+	int i;
+
+	usb_role_switch_unregister(priv->role_switch);
Quoted 8 lines

drivers/usb/dwc3/dwc3-meson-g12a.c line 519

Quoted 7 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +7 -0
+
+	of_platform_depopulate(dev);
+
+	for (i = 0 ; i < PHY_COUNT ; ++i) {
+		phy_power_off(priv->phys[i]);
+		phy_exit(priv->phys[i]);
+		phy_put(priv->phys[i]);

here, and remove others if have.

This is the last one I hope

Quoted 46 lines
Quoted 46 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +46 -0
+	}
+
+	pm_runtime_disable(dev);
+	pm_runtime_put_noidle(dev);
+	pm_runtime_set_suspended(dev);
+
+	return 0;
+}
+
+static int __maybe_unused dwc3_meson_g12a_runtime_suspend(struct device *dev)
+{
+	struct dwc3_meson_g12a	*priv = dev_get_drvdata(dev);
+
+	clk_disable(priv->clk);
+
+	return 0;
+}
+
+static int __maybe_unused dwc3_meson_g12a_runtime_resume(struct device *dev)
+{
+	struct dwc3_meson_g12a	*priv = dev_get_drvdata(dev);
+
+	return clk_enable(priv->clk);
+}
+
+static int __maybe_unused dwc3_meson_g12a_suspend(struct device *dev)
+{
+	struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
+	int i;
+
+	for (i = 0 ; i < PHY_COUNT ; ++i)
+		phy_exit(priv->phys[i]);
+
+	reset_control_assert(priv->reset);
+
+	return 0;
+}
+
+static int __maybe_unused dwc3_meson_g12a_resume(struct device *dev)
+{
+	struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
+	int i, ret;
+
+	reset_control_deassert(priv->reset);
+
+	dwc3_meson_g12a_usb_init(priv);
Quoted 8 lines

drivers/usb/dwc3/dwc3-meson-g12a.c line 504

Quoted 7 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +7 -0
+
+	/* Init PHYs */
+	for (i = 0 ; i < PHY_COUNT ; ++i) {
+		ret = phy_init(priv->phys[i]);
+		if (ret)
+			return ret;
+	}

Do you need power on phys?

Quoted 1 line

Regulators can be tied to the PHYs, should I disable power on suspend aswell ?

I find that the phy driver you used doesn't provide .power_on/off, so the current flow won't cause something wrong, but if the phy driver provides .power_on/off, it will do.

Quoted 36 lines
Quoted 23 lines
Quoted 23 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +22 -0
+
+	return 0;
+}
+
+static const struct dev_pm_ops dwc3_meson_g12a_dev_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(dwc3_meson_g12a_suspend, dwc3_meson_g12a_resume)
+	SET_RUNTIME_PM_OPS(dwc3_meson_g12a_runtime_suspend,
+			dwc3_meson_g12a_runtime_resume, NULL)
+};
+
+static const struct of_device_id dwc3_meson_g12a_match[] = {
+	{ .compatible = "amlogic,meson-g12a-usb-ctrl" },
+	{ /* Sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, dwc3_meson_g12a_match);
+
+static struct platform_driver dwc3_meson_g12a_driver = {
+	.probe		= dwc3_meson_g12a_probe,
+	.remove		= dwc3_meson_g12a_remove,
+	.driver		= {
+		.name	= "dwc3-meson-g12a",
+		.of_match_table = dwc3_meson_g12a_match,
Quoted 10 lines

drivers/usb/dwc3/dwc3-meson-g12a.c line 602

Quoted 8 lines
drivers/usb/dwc3/dwc3-meson-g12a.c new file +8 -0
+		.pm	= &dwc3_meson_g12a_dev_pm_ops,
+	},
+};
+
+module_platform_driver(dwc3_meson_g12a_driver);
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Amlogic Meson G12A USB Glue Layer");
+MODULE_AUTHOR("Neil Armstrong <[email protected]>");

Thanks,
Neil

#14 lore raw
In reply to Neil Armstrong
Quoted 18 lines · Neil Armstrong

This patchset adds support for USB on Amlogic G12A SoCs.

This patchset is composed with :
- bindings of the PHYs
- bindings of the USB Control Glue
- PHY Drivers
- USB Control Glue driver

Device Tree nodes will be added in a separate patchset.

The Amlogic G12A USB Complex is composed of :
- 2 USB Controllers :
* DWC3 for USB2 and USB3 Host functionality
* DWC2 for USB2 Peripheral functionality
- 2 USB2 OTG PHYs, only a single one will be routed to either DWC2 to DWC3
- 1 USB3 PHY shared with PCIE funcionnality
- A Glue to control PHY routing, setup and OTG detection

Quoted 8 lines

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY.

This drivers supports the on-probe setup of the OTG mode, and manually via the USB Role interface. The IRQ mode change detect is yet to be added in a future patchset, mainly due to lack of hardware to validate on.

Resent with USB2 PHY registers documented

Neil

#15 lore raw

Hi Neil,

Quoted 24 lines · Neil Armstrong
Quoted 22 lines · Neil Armstrong

This patchset adds support for USB on Amlogic G12A SoCs.

This patchset is composed with :
- bindings of the PHYs
- bindings of the USB Control Glue
- PHY Drivers
- USB Control Glue driver

Device Tree nodes will be added in a separate patchset.

The Amlogic G12A USB Complex is composed of :
- 2 USB Controllers :
* DWC3 for USB2 and USB3 Host functionality
* DWC2 for USB2 Peripheral functionality
- 2 USB2 OTG PHYs, only a single one will be routed to either DWC2 to DWC3
- 1 USB3 PHY shared with PCIE funcionnality
- A Glue to control PHY routing, setup and OTG detection

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY.

Quoted 6 lines
Quoted 4 lines

This drivers supports the on-probe setup of the OTG mode, and manually via the USB Role interface. The IRQ mode change detect is yet to be added in a future patchset, mainly due to lack of hardware to validate on.

Resent with USB2 PHY registers documented

awesome, thank you very much for this!

Regards
Martin