Skip to contentSkip to conversation

usb: convert dwc2 gadget to driver model, used in stm32mp1

PATCH New Patrick Delaunay 3 participants 30 messages Mar 29, 2019 – Apr 8, 2019

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

cover usb: convert dwc2 gadget to driver model, used in stm32mp1

This patch-set created after Marek remarks on patch
board: stm32mp1: Add tx_fifo_sz_array support
http://patchwork.ozlabs.org/patch/1056452/

This serie convert the DWC2 to driver model and use it for the stm32mp1 boards.

USB device and cable connection tested on EV1 and DK2.

This serie superseded the Patrice patches:
http://patchwork.ozlabs.org/project/uboot/list/?series=97121

Warning: the serie need to be apply after
http://patchwork.ozlabs.org/project/uboot/list/?series=91422
http://patchwork.ozlabs.org/project/uboot/list/?series=91497

Patrice Chotard (1):
usb: dwc2_udc_otg: Add tx_fifo_sz array support

Patrick Delaunay (15):
phy: usbphyc: remove unused variable index
phy: usbphyc: update xlate with DT binding
phy: usbphyc: Binding update of vdda supply
phy: usbphyc: move vdda1v1 and vdda1v8 in phy_init
phy: usbphyc: increase PLL wait timeout
usb: dwc2: remove unused variable regs_otg
usb: dwc2: convert driver to DM_USB_GADGET
usb: dwc2: force reset assert before to probe the driver
usb: dwc2: Add force-b-session-valid support
usb: dwc2: Add function for session B check
usb: dwc2_udc_otg: Read MAX_HW_ENDPOINT from HWCFG4 register
usb: dwc2: add support for STM32MP1
stm32mp1: remove CONFIG_USB_DWC2, HOST support for USBO
stm32mp1: migrate USBOTG device to driver model
stm32mp1: add stusb1600 support for DK1 and DK2 board

 arch/arm/dts/stm32mp157-pinctrl.dtsi               |   7 +
 arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi           |   3 +-
 arch/arm/dts/stm32mp157a-dk1.dts                   |  34 +-
 arch/arm/dts/stm32mp157c-ed1.dts                   |   8 -
 arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi           |   1 +
 arch/arm/dts/stm32mp157c.dtsi                      |   5 +-
 board/st/stm32mp1/stm32mp1.c                       | 185 +++-------
 configs/stm32mp15_basic_defconfig                  |   2 +-
 configs/stm32mp15_trusted_defconfig                |   2 +-
 doc/device-tree-bindings/phy/phy-stm32-usbphyc.txt |   4 +-
 doc/device-tree-bindings/usb/dwc2.txt              |  58 +++
 drivers/phy/phy-stm32-usbphyc.c                    | 111 +++---
 drivers/usb/gadget/dwc2_udc_otg.c                  | 388 ++++++++++++++++++++-
 drivers/usb/gadget/dwc2_udc_otg_priv.h             |   1 -
 drivers/usb/gadget/dwc2_udc_otg_regs.h             |  31 +-
 include/usb/dwc2_udc.h                             |   7 +
 16 files changed, 627 insertions(+), 220 deletions(-)
 create mode 100644 doc/device-tree-bindings/usb/dwc2.txt
Signature · 1 line
2.7.4
#1 lore raw

PATCH 1/16 phy: usbphyc: remove unused variable index

Remove unused field index in struct stm32_usbphyc_phy.

---

 drivers/phy/phy-stm32-usbphyc.c | 2 --
 1 file changed, 2 deletions(-)
drivers/phy/phy-stm32-usbphyc.c +0 -2
index 8e98b4b..fc53df2 100644
@@ -55,7 +55,6 @@ struct stm32_usbphyc {
 		struct udevice *vdd;
 		struct udevice *vdda1v1;
 		struct udevice *vdda1v8;
-		int index;
 		bool init;
 		bool powered;
 	} phys[MAX_PHYS];
@@ -359,7 +358,6 @@ static int stm32_usbphyc_probe(struct udevice *dev)
 	for (i = 0; i < MAX_PHYS; i++) {
 		struct stm32_usbphyc_phy *usbphyc_phy = usbphyc->phys + i;
 
-		usbphyc_phy->index = i;
 		usbphyc_phy->init = false;
 		usbphyc_phy->powered = false;
 		ret = stm32_usbphyc_get_regulator(dev, node, "phy-supply",
Signature · 1 line
2.7.4
#2 lore raw

PATCH 2/16 phy: usbphyc: update xlate with DT binding

In reply to Patrick Delaunay

Parameter added for port 1, for example:

&usbh_ehci {
	phys = <&usbphyc_port0>;
	phy-names = "usb";
	vbus-supply = <&vbus_sw>;
	status = "okay";
};
&usbotg_hs {
	pinctrl-names = "default";
	pinctrl-0 = <&usbotg_hs_pins_a>;
	phys = <&usbphyc_port1 0>;
	phy-names = "usb2-phy";
	status = "okay";
};

---

 drivers/phy/phy-stm32-usbphyc.c | 19 ++++++++++---------
 1 file changed, 10 insertions(+), 9 deletions(-)
drivers/phy/phy-stm32-usbphyc.c +10 -9
index fc53df2..ec5b47c 100644
@@ -297,19 +297,20 @@ static int stm32_usbphyc_get_regulator(struct udevice *dev, ofnode node,
 static int stm32_usbphyc_of_xlate(struct phy *phy,
 				  struct ofnode_phandle_args *args)
 {
-	if (args->args_count > 1) {
-		pr_debug("%s: invalid args_count: %d\n", __func__,
-			 args->args_count);
-		return -EINVAL;
-	}
+	if (args->args_count < 1)
+		return -ENODEV;
 
 	if (args->args[0] >= MAX_PHYS)
 		return -ENODEV;
 
-	if (args->args_count)
-		phy->id = args->args[0];
-	else
-		phy->id = 0;
+	phy->id = args->args[0];
+
+	if ((phy->id == 0 && args->args_count != 1) ||
+	    (phy->id == 1 && args->args_count != 2)) {
+		dev_err(dev, "invalid number of cells for phy port%ld\n",
+			phy->id);
+		return -EINVAL;
+	}
 
 	return 0;
 }
Signature · 1 line
2.7.4
#3 lore raw

PATCH 3/16 phy: usbphyc: Binding update of vdda supply

In reply to Patrick Delaunay

Move supply vdda1v1 and vdda1v8 in usbphyc node and no more in port

---

 arch/arm/dts/stm32mp157c-ed1.dts                   |  8 ----
 arch/arm/dts/stm32mp157c.dtsi                      |  3 ++
 doc/device-tree-bindings/phy/phy-stm32-usbphyc.txt |  4 +-
 drivers/phy/phy-stm32-usbphyc.c                    | 54 ++++++++++++----------
 4 files changed, 35 insertions(+), 34 deletions(-)
arch/arm/dts/stm32mp157c-ed1.dts +0 -8
index 2664c9c..0366782 100644
@@ -382,18 +382,10 @@
 	status = "okay";
 };
 
-&usbotg_hs {
-	usb33d-supply = <&usb33>;
-};
-
 &usbphyc_port0 {
 	phy-supply = <&vdd_usb>;
-	vdda1v1-supply = <&reg11>;
-	vdda1v8-supply = <&reg18>;
 };
 
 &usbphyc_port1 {
 	phy-supply = <&vdd_usb>;
-	vdda1v1-supply = <&reg11>;
-	vdda1v8-supply = <&reg18>;
 };
arch/arm/dts/stm32mp157c.dtsi +3 -0
index 223af2e..f1375a9 100644
@@ -836,6 +836,7 @@
 			g-np-tx-fifo-size = <32>;
 			g-tx-fifo-size = <128 128 64 64 64 64 32 32>;
 			dr_mode = "otg";
+			usb33d-supply = <&usb33>;
 			status = "disabled";
 		};
 
@@ -1165,6 +1166,8 @@
 			reg = <0x5a006000 0x1000>;
 			clocks = <&rcc USBPHY_K>;
 			resets = <&rcc USBPHY_R>;
+			vdda1v1-supply = <&reg11>;
+			vdda1v8-supply = <&reg18>;
 			status = "disabled";
 
 			usbphyc_port0: usb-phy at 0 {
doc/device-tree-bindings/phy/phy-stm32-usbphyc.txt +2 -2
index 725ae71..da98407 100644
@@ -23,6 +23,8 @@ Required properties:
 - compatible: must be "st,stm32mp1-usbphyc"
 - reg: address and length of the usb phy control register set
 - clocks: phandle + clock specifier for the PLL phy clock
+- vdda1v1-supply: phandle to the regulator providing 1V1 power to the PHY
+- vdda1v8-supply: phandle to the regulator providing 1V8 power to the PHY
 - #address-cells: number of address cells for phys sub-nodes, must be <1>
 - #size-cells: number of size cells for phys sub-nodes, must be <0>
 
@@ -40,8 +42,6 @@ Required properties:
 - reg: phy port index
 - phy-supply: phandle to the regulator providing 3V3 power to the PHY,
 	      see phy-bindings.txt in the same directory.
-- vdda1v1-supply: phandle to the regulator providing 1V1 power to the PHY
-- vdda1v8-supply: phandle to the regulator providing 1V8 power to the PHY
 - #phy-cells: see phy-bindings.txt in the same directory, must be <0> for PHY
   port#1 and must be <1> for PHY port#2, to select USB controller
 
drivers/phy/phy-stm32-usbphyc.c +30 -24

101 lines not on this page · raw message

Signature · 1 line
2.7.4
#4 lore raw

PATCH 4/16 phy: usbphyc: move vdda1v1 and vdda1v8 in phy_init

In reply to Patrick Delaunay

vdda1v1 and vdda1v8 are used by the PLL.
Both need to be enabled before starting the PLL.

---

 drivers/phy/phy-stm32-usbphyc.c | 60 +++++++++++++++++++++--------------------
 1 file changed, 31 insertions(+), 29 deletions(-)
drivers/phy/phy-stm32-usbphyc.c +31 -29
index 617c5a0..54363cd 100644
@@ -60,7 +60,8 @@ struct stm32_usbphyc {
 	} phys[MAX_PHYS];
 };
 
-void stm32_usbphyc_get_pll_params(u32 clk_rate, struct pll_params *pll_params)
+static void stm32_usbphyc_get_pll_params(u32 clk_rate,
+					 struct pll_params *pll_params)
 {
 	unsigned long long fvco, ndiv, frac;
 
@@ -153,6 +154,18 @@ static int stm32_usbphyc_phy_init(struct phy *phy)
 	if (pllen && stm32_usbphyc_is_init(usbphyc))
 		goto initialized;
 
+	if (usbphyc->vdda1v1) {
+		ret = regulator_set_enable(usbphyc->vdda1v1, true);
+		if (ret)
+			return ret;
+	}
+
+	if (usbphyc->vdda1v8) {
+		ret = regulator_set_enable(usbphyc->vdda1v8, true);
+		if (ret)
+			return ret;
+	}
+
 	if (pllen) {
 		clrbits_le32(usbphyc->base + STM32_USBPHYC_PLL, PLLEN);
 		udelay(PLL_PWR_DOWN_TIME_US);
@@ -183,6 +196,7 @@ static int stm32_usbphyc_phy_exit(struct phy *phy)
 {
 	struct stm32_usbphyc *usbphyc = dev_get_priv(phy->dev);
 	struct stm32_usbphyc_phy *usbphyc_phy = usbphyc->phys + phy->id;
+	int ret;
 
 	pr_debug("%s phy ID = %lu\n", __func__, phy->id);
 	usbphyc_phy->init = false;
@@ -202,30 +216,30 @@ static int stm32_usbphyc_phy_exit(struct phy *phy)
 	if (readl(usbphyc->base + STM32_USBPHYC_PLL) & PLLEN)
 		return -EIO;
 
-	return 0;
-}
-
-static int stm32_usbphyc_phy_power_on(struct phy *phy)
-{
-	struct stm32_usbphyc *usbphyc = dev_get_priv(phy->dev);
-	struct stm32_usbphyc_phy *usbphyc_phy = usbphyc->phys + phy->id;
-	int ret;
-
-	pr_debug("%s phy ID = %lu\n", __func__, phy->id);
 	if (usbphyc->vdda1v1) {
-		ret = regulator_set_enable(usbphyc->vdda1v1, true);
+		ret = regulator_set_enable(usbphyc->vdda1v1, false);
 		if (ret)
 			return ret;
 	}
 
 	if (usbphyc->vdda1v8) {
-		ret = regulator_set_enable(usbphyc->vdda1v8, true);
+		ret = regulator_set_enable(usbphyc->vdda1v8, false);
 		if (ret)
 			return ret;
 	}
 
-	if (usbphyc->vdd) {
-		ret = regulator_set_enable(usbphyc->vdd, true);
+	return 0;
+}
+
+static int stm32_usbphyc_phy_power_on(struct phy *phy)
+{
+	struct stm32_usbphyc *usbphyc = dev_get_priv(phy->dev);
+	struct stm32_usbphyc_phy *usbphyc_phy = usbphyc->phys + phy->id;
+	int ret;
+
+	pr_debug("%s phy ID = %lu\n", __func__, phy->id);
+	if (usbphyc_phy->vdd) {
+		ret = regulator_set_enable(usbphyc_phy->vdd, true);
 		if (ret)
 			return ret;
 	}
@@ -247,20 +261,8 @@ static int stm32_usbphyc_phy_power_off(struct phy *phy)
 	if (stm32_usbphyc_is_powered(usbphyc))
 		return 0;
 
-	if (usbphyc->vdda1v1) {
-		ret = regulator_set_enable(usbphyc->vdda1v1, false);
-		if (ret)
-			return ret;
-	}
-
-	if (usbphyc->vdda1v8) {
-		ret = regulator_set_enable(usbphyc->vdda1v8, false);
-		if (ret)
-			return ret;
-	}
-
-	if (usbphyc->vdd) {
-		ret = regulator_set_enable(usbphyc->vdd, false);
+	if (usbphyc_phy->vdd) {
+		ret = regulator_set_enable(usbphyc_phy->vdd, false);
 		if (ret)
 			return ret;
 	}
Signature · 1 line
2.7.4
#5 lore raw

PATCH 5/16 phy: usbphyc: increase PLL wait timeout

In reply to Patrick Delaunay

wait 200us to solve USB init issue on device mode
(ums and stm32prog commands)

---

 drivers/phy/phy-stm32-usbphyc.c | 10 ++++------
 1 file changed, 4 insertions(+), 6 deletions(-)
drivers/phy/phy-stm32-usbphyc.c +4 -6
index 54363cd..6f11190 100644
@@ -37,7 +37,8 @@
 
 #define MAX_PHYS		2
 
-#define PLL_LOCK_TIME_US	100
+/* max 100 us for PLL lock and 100 us for PHY init */
+#define PLL_INIT_TIME_US	200
 #define PLL_PWR_DOWN_TIME_US	5
 #define PLL_FVCO		2880	 /* in MHz */
 #define PLL_INFF_MIN_RATE	19200000 /* in Hz */
@@ -177,11 +178,8 @@ static int stm32_usbphyc_phy_init(struct phy *phy)
 
 	setbits_le32(usbphyc->base + STM32_USBPHYC_PLL, PLLEN);
 
-	/*
-	 * We must wait PLL_LOCK_TIME_US before checking that PLLEN
-	 * bit is still set
-	 */
-	udelay(PLL_LOCK_TIME_US);
+	/* We must wait PLL_INIT_TIME_US before using PHY */
+	udelay(PLL_INIT_TIME_US);
 
 	if (!(readl(usbphyc->base + STM32_USBPHYC_PLL) & PLLEN))
 		return -EIO;
Signature · 1 line
2.7.4
#6 lore raw

PATCH 6/16 usb: dwc2: remove unused variable regs_otg

In reply to Patrick Delaunay

Remove the global regs_otg variable.

---

 drivers/usb/gadget/dwc2_udc_otg.c | 3 ---
 1 file changed, 3 deletions(-)
drivers/usb/gadget/dwc2_udc_otg.c +0 -3
index 3c7ad03..edca05d 100644
@@ -140,7 +140,6 @@ static struct usb_ep_ops dwc2_ep_ops = {
 
 /***********************************************************/
 
-void __iomem		*regs_otg;
 struct dwc2_usbotg_reg *reg;
 
 bool dfu_usb_get_reset(void)
@@ -818,8 +817,6 @@ int dwc2_udc_probe(struct dwc2_plat_otg_data *pdata)
 
 	reg = (struct dwc2_usbotg_reg *)pdata->regs_otg;
 
-	/* regs_otg = (void *)pdata->regs_otg; */
-
 	dev->gadget.is_dualspeed = 1;	/* Hack only*/
 	dev->gadget.is_otg = 0;
 	dev->gadget.is_a_peripheral = 0;
Signature · 1 line
2.7.4
#7 lore raw

PATCH 6/16 usb: dwc2: remove unused variable regs_otg

Quoted 21 lines · On Fri, 29 Mar 2019 15:42:14 +0100 Patrick Delaunay <[email protected]>…

Remove the global regs_otg variable.

---

 drivers/usb/gadget/dwc2_udc_otg.c | 3 ---
 1 file changed, 3 deletions(-)
(quoted diff) +0 -0

b/drivers/usb/gadget/dwc2_udc_otg.c index 3c7ad03..edca05d 100644

drivers/usb/gadget/dwc2_udc_otg.c +0 -1
@@ -140,7 +140,6 @@ static struct usb_ep_ops dwc2_ep_ops = {
 
 /***********************************************************/
 
-void __iomem		*regs_otg;
 struct dwc2_usbotg_reg *reg;
 
 bool dfu_usb_get_reset(void)

drivers/usb/gadget/dwc2_udc_otg.c int dwc2_udc_probe(struct dwc2_plat_otg_data · line 822

Quoted 8 lines
drivers/usb/gadget/dwc2_udc_otg.c +0 -2
@@ -818,8 +817,6 @@ int dwc2_udc_probe(struct dwc2_plat_otg_data
 *pdata) 
 	reg = (struct dwc2_usbotg_reg *)pdata->regs_otg;
 
-	/* regs_otg = (void *)pdata->regs_otg; */
-
 	dev->gadget.is_dualspeed = 1;	/* Hack only*/
 	dev->gadget.is_otg = 0;
 	dev->gadget.is_a_peripheral = 0;

Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de -------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190408/3ea7f984/attachment.sig>

#8 lore raw

PATCH 7/16 usb: dwc2: convert driver to DM_USB_GADGET

In reply to Patrick Delaunay

Minimal conversion to driver model by using the uclass UCLASS_USB_GADGET_GENERIC based on:
- reset uclass
- clock uclass
- generic uclass.

---

 doc/device-tree-bindings/usb/dwc2.txt |  54 +++++++
 drivers/usb/gadget/dwc2_udc_otg.c     | 292 +++++++++++++++++++++++++++++++++-
 2 files changed, 344 insertions(+), 2 deletions(-)
 create mode 100644 doc/device-tree-bindings/usb/dwc2.txt
doc/device-tree-bindings/usb/dwc2.txt new file +54 -0
new file mode 100644
index 0000000..6dc3c4a
@@ -0,0 +1,54 @@
+Platform DesignWare HS OTG USB 2.0 controller
+-----------------------------------------------------
+
+Required properties:
+- compatible : One of:
+  - brcm,bcm2835-usb: The DWC2 USB controller instance in the BCM2835 SoC.
+  - hisilicon,hi6220-usb: The DWC2 USB controller instance in the hi6220 SoC.
+  - rockchip,rk3066-usb: The DWC2 USB controller instance in the rk3066 Soc;
+  - "rockchip,px30-usb", "rockchip,rk3066-usb", "snps,dwc2": for px30 Soc;
+  - "rockchip,rk3188-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3188 Soc;
+  - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc;
+  - "lantiq,arx100-usb": The DWC2 USB controller instance in Lantiq ARX SoCs;
+  - "lantiq,xrx200-usb": The DWC2 USB controller instance in Lantiq XRX SoCs;
+  - "amlogic,meson8-usb": The DWC2 USB controller instance in Amlogic Meson8 SoCs;
+  - "amlogic,meson8b-usb": The DWC2 USB controller instance in Amlogic Meson8b SoCs;
+  - "amlogic,meson-gxbb-usb": The DWC2 USB controller instance in Amlogic S905 SoCs;
+  - "amcc,dwc-otg": The DWC2 USB controller instance in AMCC Canyonlands 460EX SoCs;
+  - snps,dwc2: A generic DWC2 USB controller with default parameters.
+  - "st,stm32f4x9-fsotg": The DWC2 USB FS/HS controller instance in STM32F4x9 SoCs
+  configured in FS mode;
+  - "st,stm32f4x9-hsotg": The DWC2 USB HS controller instance in STM32F4x9 SoCs
+  configured in HS mode;
+  - "st,stm32f7-hsotg": The DWC2 USB HS controller instance in STM32F7 SoCs
+    configured in HS mode;
+- reg : Should contain 1 register range (address and length)
+- interrupts : Should contain 1 interrupt
+- clocks: clock provider specifier
+- clock-names: shall be "otg"
+Refer to clk/clock-bindings.txt for generic clock consumer properties
+
+Optional properties:
+- phys: phy provider specifier
+- phy-names: shall be "usb2-phy"
+Refer to phy/phy-bindings.txt for generic phy consumer properties
+- dr_mode: shall be one of "host", "peripheral" and "otg"
+  Refer to usb/generic.txt
+- g-rx-fifo-size: size of rx fifo size in gadget mode.
+- g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode.
+- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode.
+
+Deprecated properties:
+- g-use-dma: gadget DMA mode is automatically detected
+
+Example:
+
+        usb at 101c0000 {
+                compatible = "ralink,rt3050-usb, snps,dwc2";
+                reg = <0x101c0000 40000>;
+                interrupts = <18>;
+		clocks = <&usb_otg_ahb_clk>;
+		clock-names = "otg";
+		phys = <&usbphy>;
+		phy-names = "usb2-phy";
+        };
drivers/usb/gadget/dwc2_udc_otg.c +290 -2

337 lines not on this page · raw message

Signature · 1 line
2.7.4
#9 lore raw

PATCH 7/16 usb: dwc2: convert driver to DM_USB_GADGET

Quoted 442 lines · On Fri, 29 Mar 2019 15:42:15 +0100 Patrick Delaunay <[email protected]>…

Minimal conversion to driver model by using the uclass UCLASS_USB_GADGET_GENERIC based on:
- reset uclass
- clock uclass
- generic uclass.

---

 doc/device-tree-bindings/usb/dwc2.txt |  54 +++++++
 drivers/usb/gadget/dwc2_udc_otg.c     | 292

+++++++++++++++++++++++++++++++++- 2 files changed, 344 insertions(+), 2 deletions(-) create mode 100644 doc/device-tree-bindings/usb/dwc2.txt

(quoted diff) +0 -0

b/doc/device-tree-bindings/usb/dwc2.txt new file mode 100644 index 0000000..6dc3c4a

doc/device-tree-bindings/usb/dwc2.txt new file +6 -0
@@ -0,0 +1,54 @@
+Platform DesignWare HS OTG USB 2.0 controller
+-----------------------------------------------------
+
+Required properties:
+- compatible : One of:
+  - brcm,bcm2835-usb: The DWC2 USB controller instance in the

BCM2835 SoC.
+ - hisilicon,hi6220-usb: The DWC2 USB controller instance in the hi6220 SoC.
+ - rockchip,rk3066-usb: The DWC2 USB controller instance in the rk3066 Soc;
+ - "rockchip,px30-usb", "rockchip,rk3066-usb", "snps,dwc2": for px30 Soc;
+ - "rockchip,rk3188-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3188 Soc;
+ - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc;
+ - "lantiq,arx100-usb": The DWC2 USB controller instance in Lantiq ARX SoCs;
+ - "lantiq,xrx200-usb": The DWC2 USB controller instance in Lantiq XRX SoCs;
+ - "amlogic,meson8-usb": The DWC2 USB controller instance in Amlogic Meson8 SoCs;
+ - "amlogic,meson8b-usb": The DWC2 USB controller instance in Amlogic Meson8b SoCs;
+ - "amlogic,meson-gxbb-usb": The DWC2 USB controller instance in Amlogic S905 SoCs;
+ - "amcc,dwc-otg": The DWC2 USB controller instance in AMCC Canyonlands 460EX SoCs;

doc/device-tree-bindings/usb/dwc2.txt new file +2 -0
+  - snps,dwc2: A generic DWC2 USB controller with default parameters.
+  - "st,stm32f4x9-fsotg": The DWC2 USB FS/HS controller instance in

STM32F4x9 SoCs

doc/device-tree-bindings/usb/dwc2.txt new file +2 -0
+  configured in FS mode;
+  - "st,stm32f4x9-hsotg": The DWC2 USB HS controller instance in

STM32F4x9 SoCs

doc/device-tree-bindings/usb/dwc2.txt new file +2 -0
+  configured in HS mode;
+  - "st,stm32f7-hsotg": The DWC2 USB HS controller instance in

STM32F7 SoCs

doc/device-tree-bindings/usb/dwc2.txt new file +15 -0
+    configured in HS mode;
+- reg : Should contain 1 register range (address and length)
+- interrupts : Should contain 1 interrupt
+- clocks: clock provider specifier
+- clock-names: shall be "otg"
+Refer to clk/clock-bindings.txt for generic clock consumer properties
+
+Optional properties:
+- phys: phy provider specifier
+- phy-names: shall be "usb2-phy"
+Refer to phy/phy-bindings.txt for generic phy consumer properties
+- dr_mode: shall be one of "host", "peripheral" and "otg"
+  Refer to usb/generic.txt
+- g-rx-fifo-size: size of rx fifo size in gadget mode.
+- g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget

mode. +- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode. +

doc/device-tree-bindings/usb/dwc2.txt new file +14 -0
+Deprecated properties:
+- g-use-dma: gadget DMA mode is automatically detected
+
+Example:
+
+        usb at 101c0000 {
+                compatible = "ralink,rt3050-usb, snps,dwc2";
+                reg = <0x101c0000 40000>;
+                interrupts = <18>;
+		clocks = <&usb_otg_ahb_clk>;
+		clock-names = "otg";
+		phys = <&usbphy>;
+		phy-names = "usb2-phy";
+        };
(quoted diff) +0 -0

b/drivers/usb/gadget/dwc2_udc_otg.c index edca05d..af16fc1 100644

drivers/usb/gadget/dwc2_udc_otg.c +18 -1
@@ -18,11 +18,17 @@
  */
 #undef DEBUG
 #include <common.h>
+#include <clk.h>
+#include <dm.h>
+#include <generic-phy.h>
+#include <malloc.h>
+#include <reset.h>
+
 #include <linux/errno.h>
 #include <linux/list.h>
-#include <malloc.h>
 
 #include <linux/usb/ch9.h>
+#include <linux/usb/otg.h>
 #include <linux/usb/gadget.h>
 
 #include <asm/byteorder.h>
@@ -31,6 +37,8 @@
 
 #include <asm/mach-types.h>
 
+#include <power/regulator.h>
+
 #include "dwc2_udc_otg_regs.h"
 #include "dwc2_udc_otg_priv.h"
 
@@ -222,6 +230,7 @@ static int udc_enable(struct dwc2_udc *dev)
 	return 0;
 }
 
+#if !CONFIG_IS_ENABLED(DM_USB_GADGET)
 /*
   Register entry point for the peripheral controller driver.
 */
@@ -296,6 +305,54 @@ int usb_gadget_unregister_driver(struct
 usb_gadget_driver *driver) udc_disable(dev);
 	return 0;
 }
+#else /* !CONFIG_IS_ENABLED(DM_USB_GADGET) */
+
+static int dwc2_gadget_start(struct usb_gadget *g,
+			     struct usb_gadget_driver *driver)
+{
+	struct dwc2_udc *dev = the_controller;
+
+	debug_cond(DEBUG_SETUP != 0, "%s: %s\n", __func__, "no

name"); +

drivers/usb/gadget/dwc2_udc_otg.c +17 -0
+	if (!driver ||
+	    (driver->speed != USB_SPEED_FULL &&
+	     driver->speed != USB_SPEED_HIGH) ||
+	    !driver->bind || !driver->disconnect || !driver->setup)
+		return -EINVAL;
+
+	if (!dev)
+		return -ENODEV;
+
+	if (dev->driver)
+		return -EBUSY;
+
+	/* first hook up the driver ... */
+	dev->driver = driver;
+
+	debug_cond(DEBUG_SETUP != 0,
+		   "Registered gadget driver %s\n",

dev->gadget.name);

drivers/usb/gadget/dwc2_udc_otg.c +73 -1
+	return udc_enable(dev);
+}
+
+static int dwc2_gadget_stop(struct usb_gadget *g)
+{
+	struct dwc2_udc *dev = the_controller;
+
+	if (!dev)
+		return -ENODEV;
+
+	if (!dev->driver)
+		return -EINVAL;
+
+	dev->driver = 0;
+	stop_activity(dev, dev->driver);
+
+	udc_disable(dev);
+
+	return 0;
+}
+
+#endif /* !CONFIG_IS_ENABLED(DM_USB_GADGET) */
 
 /*
  *	done - retire a request; caller blocked irqs
@@ -730,6 +787,10 @@ static void dwc2_fifo_flush(struct usb_ep *_ep)
 
 static const struct usb_gadget_ops dwc2_udc_ops = {
 	/* current versions must always be self-powered */
+#if CONFIG_IS_ENABLED(DM_USB_GADGET)
+	.udc_start		= dwc2_gadget_start,
+	.udc_stop		= dwc2_gadget_stop,
+#endif
 };
 
 static struct dwc2_udc memory = {
@@ -841,12 +902,239 @@ int dwc2_udc_probe(struct dwc2_plat_otg_data
 *pdata) return retval;
 }
 
-int usb_gadget_handle_interrupts(int index)
+int dwc2_udc_handle_interrupt(void)
 {
 	u32 intr_status = readl(&reg->gintsts);
 	u32 gintmsk = readl(&reg->gintmsk);
 
 	if (intr_status & gintmsk)
 		return dwc2_udc_irq(1, (void *)the_controller);
+
+	return 0;
+}
+
+#if !CONFIG_IS_ENABLED(DM_USB_GADGET)
+
+int usb_gadget_handle_interrupts(int index)
+{
+	return dwc2_udc_handle_interrupt();
+}
+
+#else /* CONFIG_IS_ENABLED(DM_USB_GADGET) */
+
+struct dwc2_priv_data {
+	struct clk_bulk		clks;
+	struct reset_ctl_bulk	resets;
+	struct phy *phys;
+	int num_phys;
+};
+
+int dm_usb_gadget_handle_interrupts(struct udevice *dev)
+{
+	return dwc2_udc_handle_interrupt();
+}
+
+int dwc2_phy_setup(struct udevice *dev, struct phy **array, int
 *num_phys) +{
+	int i, ret, count;
+	struct phy *usb_phys;
+
+	/* Return if no phy declared */
+	if (!dev_read_prop(dev, "phys", NULL))
+		return 0;
+
+	count = dev_count_phandle_with_args(dev, "phys",
 "#phy-cells");
+	if (count <= 0)
+		return count;
+
+	usb_phys = devm_kcalloc(dev, count, sizeof(struct phy),
+				GFP_KERNEL);
+	if (!usb_phys)
+		return -ENOMEM;
+
+	for (i = 0; i < count; i++) {
+		ret = generic_phy_get_by_index(dev, i, &usb_phys[i]);
+		if (ret && ret != -ENOENT) {
+			dev_err(dev, "Failed to get USB PHY%d for

%s\n",

drivers/usb/gadget/dwc2_udc_otg.c +18 -0
+				i, dev->name);
+			return ret;
+		}
+	}
+
+	for (i = 0; i < count; i++) {
+		ret = generic_phy_init(&usb_phys[i]);
+		if (ret) {
+			dev_err(dev, "Can't init USB PHY%d for %s\n",
+				i, dev->name);
+			goto phys_init_err;
+		}
+	}
+
+	for (i = 0; i < count; i++) {
+		ret = generic_phy_power_on(&usb_phys[i]);
+		if (ret) {
+			dev_err(dev, "Can't power USB PHY%d for

%s\n",

drivers/usb/gadget/dwc2_udc_otg.c +25 -0
+				i, dev->name);
+			goto phys_poweron_err;
+		}
+	}
+
+	*array = usb_phys;
+	*num_phys =  count;
+
 	return 0;
+
+phys_poweron_err:
+	for (i = count - 1; i >= 0; i--)
+		generic_phy_power_off(&usb_phys[i]);
+
+	for (i = 0; i < count; i++)
+		generic_phy_exit(&usb_phys[i]);
+
+	return ret;
+
+phys_init_err:
+	for (; i >= 0; i--)
+		generic_phy_exit(&usb_phys[i]);
+
+	return ret;
 }
+
+void dwc2_phy_shutdown(struct udevice *dev, struct phy *usb_phys,

int num_phys) +{

drivers/usb/gadget/dwc2_udc_otg.c +10 -0
+	int i, ret;
+
+	for (i = 0; i < num_phys; i++) {
+		if (!generic_phy_valid(&usb_phys[i]))
+			continue;
+
+		ret = generic_phy_power_off(&usb_phys[i]);
+		ret |= generic_phy_exit(&usb_phys[i]);
+		if (ret) {
+			dev_err(dev, "Can't shutdown USB PHY%d for

%s\n",

drivers/usb/gadget/dwc2_udc_otg.c +18 -0
+				i, dev->name);
+		}
+	}
+}
+
+static int dwc2_udc_otg_ofdata_to_platdata(struct udevice *dev)
+{
+	struct dwc2_plat_otg_data *platdata = dev_get_platdata(dev);
+	int node = dev_of_offset(dev);
+
+	if (usb_get_dr_mode(node) != USB_DR_MODE_PERIPHERAL) {
+		dev_dbg(dev, "Invalid mode\n");
+		return -ENODEV;
+	}
+
+	platdata->regs_otg = dev_read_addr(dev);
+
+	platdata->rx_fifo_sz = dev_read_u32_default(dev,

"g-rx-fifo-size", 0);

drivers/usb/gadget/dwc2_udc_otg.c +2 -0
+	platdata->np_tx_fifo_sz = dev_read_u32_default(dev,
+

"g-np-tx-fifo-size", 0);

drivers/usb/gadget/dwc2_udc_otg.c +1 -0
+	platdata->tx_fifo_sz = dev_read_u32_default(dev,

"g-tx-fifo-size", 0); +

drivers/usb/gadget/dwc2_udc_otg.c +70 -0
+	return 0;
+}
+
+static int dwc2_udc_otg_reset_init(struct udevice *dev,
+				   struct reset_ctl_bulk *resets)
+{
+	int ret;
+
+	ret = reset_get_bulk(dev, resets);
+	if (ret == -ENOTSUPP)
+		return 0;
+
+	if (ret)
+		return ret;
+
+	ret = reset_deassert_bulk(resets);
+	if (ret) {
+		reset_release_bulk(resets);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int dwc2_udc_otg_clk_init(struct udevice *dev,
+				 struct clk_bulk *clks)
+{
+	int ret;
+
+	ret = clk_get_bulk(dev, clks);
+	if (ret == -ENOSYS)
+		return 0;
+
+	if (ret)
+		return ret;
+
+	ret = clk_enable_bulk(clks);
+	if (ret) {
+		clk_release_bulk(clks);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int dwc2_udc_otg_probe(struct udevice *dev)
+{
+	struct dwc2_plat_otg_data *platdata = dev_get_platdata(dev);
+	struct dwc2_priv_data *priv = dev_get_priv(dev);
+	int ret;
+
+	ret = dwc2_udc_otg_clk_init(dev, &priv->clks);
+	if (ret)
+		return ret;
+
+	ret = dwc2_udc_otg_reset_init(dev, &priv->resets);
+	if (ret)
+		return ret;
+
+	ret = dwc2_phy_setup(dev, &priv->phys, &priv->num_phys);
+	if (ret)
+		return ret;
+
+	ret = dwc2_udc_probe(platdata);
+	if (ret)
+		return ret;
+
+	the_controller->driver = 0;
+
+	ret = usb_add_gadget_udc((struct device *)dev,

&the_controller->gadget); +

drivers/usb/gadget/dwc2_udc_otg.c +30 -0
+	return ret;
+}
+
+static int dwc2_udc_otg_remove(struct udevice *dev)
+{
+	struct dwc2_priv_data *priv = dev_get_priv(dev);
+
+	usb_del_gadget_udc(&the_controller->gadget);
+
+	reset_release_bulk(&priv->resets);
+
+	clk_release_bulk(&priv->clks);
+
+	dwc2_phy_shutdown(dev, priv->phys, priv->num_phys);
+
+	return dm_scan_fdt_dev(dev);
+}
+
+static const struct udevice_id dwc2_udc_otg_ids[] = {
+	{ .compatible = "snps,dwc2" },
+};
+
+U_BOOT_DRIVER(dwc2_udc_otg) = {
+	.name	= "dwc2-udc-otg",
+	.id	= UCLASS_USB_GADGET_GENERIC,
+	.of_match = dwc2_udc_otg_ids,
+	.ofdata_to_platdata = dwc2_udc_otg_ofdata_to_platdata,
+	.probe = dwc2_udc_otg_probe,
+	.remove = dwc2_udc_otg_remove,
+	.platdata_auto_alloc_size = sizeof(struct

dwc2_plat_otg_data),

drivers/usb/gadget/dwc2_udc_otg.c int dwc2_udc_probe(struct dwc2_plat_otg_data *pdata) · line 1140

Quoted 3 lines
drivers/usb/gadget/dwc2_udc_otg.c +3 -0
+	.priv_auto_alloc_size = sizeof(struct dwc2_priv_data),
+};
+#endif /* CONFIG_IS_ENABLED(DM_USB_GADGET) */

Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de -------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190408/a391d385/attachment.sig>

#10 lore raw

PATCH 8/16 usb: dwc2: force reset assert before to probe the driver

In reply to Patrick Delaunay

Reset the hardware to be sure of the device state.

---

 drivers/usb/gadget/dwc2_udc_otg.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)
drivers/usb/gadget/dwc2_udc_otg.c +6 -1
index af16fc1..8169fdb 100644
@@ -1049,7 +1049,12 @@ static int dwc2_udc_otg_reset_init(struct udevice *dev,
 	if (ret)
 		return ret;
 
-	ret = reset_deassert_bulk(resets);
+	ret = reset_assert_bulk(resets);
+
+	if (!ret) {
+		udelay(2);
+		ret = reset_deassert_bulk(resets);
+	}
 	if (ret) {
 		reset_release_bulk(resets);
 		return ret;
Signature · 1 line
2.7.4
#11 lore raw

PATCH 8/16 usb: dwc2: force reset assert before to probe the driver

Quoted 16 lines · On Fri, 29 Mar 2019 15:42:16 +0100 Patrick Delaunay <[email protected]>…

Reset the hardware to be sure of the device state.

---

 drivers/usb/gadget/dwc2_udc_otg.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)
(quoted diff) +0 -0

b/drivers/usb/gadget/dwc2_udc_otg.c index af16fc1..8169fdb 100644

drivers/usb/gadget/dwc2_udc_otg.c +0 -0
@@ -1049,7 +1049,12 @@ static int dwc2_udc_otg_reset_init(struct
 udevice *dev, if (ret)
 		return ret;
 

drivers/usb/gadget/dwc2_udc_otg.c static int dwc2_udc_otg_reset_init(struct · line 1060

Quoted 10 lines
drivers/usb/gadget/dwc2_udc_otg.c +6 -1
-	ret = reset_deassert_bulk(resets);
+	ret = reset_assert_bulk(resets);
+
+	if (!ret) {
+		udelay(2);
+		ret = reset_deassert_bulk(resets);
+	}
 	if (ret) {
 		reset_release_bulk(resets);
 		return ret;

Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de -------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190408/01f94779/attachment.sig>

#12 lore raw

PATCH 9/16 usb: dwc2: Add force-b-session-valid support

In reply to Patrick Delaunay

Handle "force-b-session-valid" property from DT.

---

 drivers/usb/gadget/dwc2_udc_otg.c      | 9 +++++++++
 drivers/usb/gadget/dwc2_udc_otg_regs.h | 8 ++++++--
 include/usb/dwc2_udc.h                 | 1 +
 3 files changed, 16 insertions(+), 2 deletions(-)
drivers/usb/gadget/dwc2_udc_otg.c +9 -0
index 8169fdb..146f11e 100644
@@ -1034,6 +1034,9 @@ static int dwc2_udc_otg_ofdata_to_platdata(struct udevice *dev)
 						       "g-np-tx-fifo-size", 0);
 	platdata->tx_fifo_sz = dev_read_u32_default(dev, "g-tx-fifo-size", 0);
 
+	platdata->force_b_session_valid =
+		dev_read_bool(dev, "force-b-session-valid");
+
 	return 0;
 }
 
@@ -1088,6 +1091,8 @@ static int dwc2_udc_otg_probe(struct udevice *dev)
 {
 	struct dwc2_plat_otg_data *platdata = dev_get_platdata(dev);
 	struct dwc2_priv_data *priv = dev_get_priv(dev);
+	struct dwc2_usbotg_reg *usbotg_reg =
+		(struct dwc2_usbotg_reg *)platdata->regs_otg;
 	int ret;
 
 	ret = dwc2_udc_otg_clk_init(dev, &priv->clks);
@@ -1102,6 +1107,10 @@ static int dwc2_udc_otg_probe(struct udevice *dev)
 	if (ret)
 		return ret;
 
+	if (platdata->force_b_session_valid)
+		/* Override B session bits : value and enable */
+		setbits_le32(&usbotg_reg->gotgctl,  B_VALOEN | B_VALOVAL);
+
 	ret = dwc2_udc_probe(platdata);
 	if (ret)
 		return ret;
drivers/usb/gadget/dwc2_udc_otg_regs.h +6 -2
index a1829b3..0aee4ee 100644
@@ -83,8 +83,12 @@ struct dwc2_usbotg_reg {
 /*definitions related to CSR setting */
 
 /* DWC2_UDC_OTG_GOTGCTL */
-#define B_SESSION_VALID		(0x1<<19)
-#define A_SESSION_VALID		(0x1<<18)
+#define B_SESSION_VALID			BIT(19)
+#define A_SESSION_VALID			BIT(18)
+#define B_VALOVAL			BIT(7)
+#define B_VALOEN			BIT(6)
+#define A_VALOVAL			BIT(5)
+#define A_VALOEN			BIT(4)
 
 /* DWC2_UDC_OTG_GAHBCFG */
 #define PTXFE_HALF			(0<<8)
include/usb/dwc2_udc.h +1 -0
index 4068de0..3cf20ea 100644
@@ -22,6 +22,7 @@ struct dwc2_plat_otg_data {
 	unsigned int	rx_fifo_sz;
 	unsigned int	np_tx_fifo_sz;
 	unsigned int	tx_fifo_sz;
+	bool		force_b_session_valid;
 };
 
 int dwc2_udc_probe(struct dwc2_plat_otg_data *pdata);
Signature · 1 line
2.7.4
#13 lore raw

PATCH 9/16 usb: dwc2: Add force-b-session-valid support

Quoted 68 lines · On Fri, 29 Mar 2019 15:42:17 +0100 Patrick Delaunay <[email protected]>…

Handle "force-b-session-valid" property from DT.

---

 drivers/usb/gadget/dwc2_udc_otg.c      | 9 +++++++++
 drivers/usb/gadget/dwc2_udc_otg_regs.h | 8 ++++++--
 include/usb/dwc2_udc.h                 | 1 +
 3 files changed, 16 insertions(+), 2 deletions(-)
(quoted diff) +0 -0

b/drivers/usb/gadget/dwc2_udc_otg.c index 8169fdb..146f11e 100644

drivers/usb/gadget/dwc2_udc_otg.c +0 -0
@@ -1034,6 +1034,9 @@ static int
 dwc2_udc_otg_ofdata_to_platdata(struct udevice *dev)

"g-np-tx-fifo-size", 0); platdata->tx_fifo_sz =
dev_read_u32_default(dev, "g-tx-fifo-size", 0);

drivers/usb/gadget/dwc2_udc_otg.c +8 -0
+	platdata->force_b_session_valid =
+		dev_read_bool(dev, "force-b-session-valid");
+
 	return 0;
 }
@@ -1088,6 +1091,8 @@ static int dwc2_udc_otg_probe(struct udevice
 *dev) {
 	struct dwc2_plat_otg_data *platdata = dev_get_platdata(dev);
 	struct dwc2_priv_data *priv = dev_get_priv(dev);
+	struct dwc2_usbotg_reg *usbotg_reg =
+		(struct dwc2_usbotg_reg *)platdata->regs_otg;
 	int ret;
 
 	ret = dwc2_udc_otg_clk_init(dev, &priv->clks);
@@ -1102,6 +1107,10 @@ static int dwc2_udc_otg_probe(struct udevice
 *dev) if (ret)
 		return ret;
 
+	if (platdata->force_b_session_valid)
+		/* Override B session bits : value and enable */
+		setbits_le32(&usbotg_reg->gotgctl,  B_VALOEN |

B_VALOVAL); +

drivers/usb/gadget/dwc2_udc_otg.c +0 -0
 	ret = dwc2_udc_probe(platdata);
 	if (ret)
 		return ret;
(quoted diff) +0 -0

b/drivers/usb/gadget/dwc2_udc_otg_regs.h index a1829b3..0aee4ee 100644

drivers/usb/gadget/dwc2_udc_otg_regs.h +6 -2
@@ -83,8 +83,12 @@ struct dwc2_usbotg_reg {
 /*definitions related to CSR setting */
 
 /* DWC2_UDC_OTG_GOTGCTL */
-#define B_SESSION_VALID		(0x1<<19)
-#define A_SESSION_VALID		(0x1<<18)
+#define B_SESSION_VALID			BIT(19)
+#define A_SESSION_VALID			BIT(18)
+#define B_VALOVAL			BIT(7)
+#define B_VALOEN			BIT(6)
+#define A_VALOVAL			BIT(5)
+#define A_VALOEN			BIT(4)
 
 /* DWC2_UDC_OTG_GAHBCFG */
 #define PTXFE_HALF			(0<<8)
include/usb/dwc2_udc.h +0 -0
index 4068de0..3cf20ea 100644

include/usb/dwc2_udc.h struct dwc2_plat_otg_data { · line 28

Quoted 7 lines
include/usb/dwc2_udc.h +1 -0
@@ -22,6 +22,7 @@ struct dwc2_plat_otg_data {
 	unsigned int	rx_fifo_sz;
 	unsigned int	np_tx_fifo_sz;
 	unsigned int	tx_fifo_sz;
+	bool		force_b_session_valid;
 };
 
 int dwc2_udc_probe(struct dwc2_plat_otg_data *pdata);

Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de -------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190408/7a0bfaf8/attachment.sig>

#14 lore raw

PATCH 10/16 usb: dwc2: Add function for session B check

In reply to Patrick Delaunay

Add a new function to check the session B validity, to be use to check cable connection.

---

 drivers/usb/gadget/dwc2_udc_otg.c | 9 +++++++++
 include/usb/dwc2_udc.h            | 2 ++
 2 files changed, 11 insertions(+)
drivers/usb/gadget/dwc2_udc_otg.c +9 -0
index 146f11e..b1efad1 100644
@@ -1151,4 +1151,13 @@ U_BOOT_DRIVER(dwc2_udc_otg) = {
 	.platdata_auto_alloc_size = sizeof(struct dwc2_plat_otg_data),
 	.priv_auto_alloc_size = sizeof(struct dwc2_priv_data),
 };
+
+int dwc2_udc_B_session_valid(struct udevice *dev)
+{
+	struct dwc2_plat_otg_data *platdata = dev_get_platdata(dev);
+	struct dwc2_usbotg_reg *usbotg_reg =
+		(struct dwc2_usbotg_reg *)platdata->regs_otg;
+
+	return readl(&usbotg_reg->gotgctl) & B_SESSION_VALID;
+}
 #endif /* CONFIG_IS_ENABLED(DM_USB_GADGET) */
include/usb/dwc2_udc.h +2 -0
index 3cf20ea..8a426b6 100644
@@ -27,4 +27,6 @@ struct dwc2_plat_otg_data {
 
 int dwc2_udc_probe(struct dwc2_plat_otg_data *pdata);
 
+int dwc2_udc_B_session_valid(struct udevice *dev);
+
 #endif	/* __DWC2_USB_GADGET */
Signature · 1 line
2.7.4
#15 lore raw

PATCH 10/16 usb: dwc2: Add function for session B check

Quoted 33 lines · On Fri, 29 Mar 2019 15:42:18 +0100 Patrick Delaunay <[email protected]>…

Add a new function to check the session B validity, to be use to check cable connection.

---

 drivers/usb/gadget/dwc2_udc_otg.c | 9 +++++++++
 include/usb/dwc2_udc.h            | 2 ++
 2 files changed, 11 insertions(+)
(quoted diff) +0 -0

b/drivers/usb/gadget/dwc2_udc_otg.c index 146f11e..b1efad1 100644

drivers/usb/gadget/dwc2_udc_otg.c +0 -0
@@ -1151,4 +1151,13 @@ U_BOOT_DRIVER(dwc2_udc_otg) = {
 	.platdata_auto_alloc_size = sizeof(struct

dwc2_plat_otg_data), .priv_auto_alloc_size = sizeof(struct dwc2_priv_data), };

drivers/usb/gadget/dwc2_udc_otg.c +9 -0
+
+int dwc2_udc_B_session_valid(struct udevice *dev)
+{
+	struct dwc2_plat_otg_data *platdata = dev_get_platdata(dev);
+	struct dwc2_usbotg_reg *usbotg_reg =
+		(struct dwc2_usbotg_reg *)platdata->regs_otg;
+
+	return readl(&usbotg_reg->gotgctl) & B_SESSION_VALID;
+}
 #endif /* CONFIG_IS_ENABLED(DM_USB_GADGET) */
include/usb/dwc2_udc.h +0 -0
index 3cf20ea..8a426b6 100644

include/usb/dwc2_udc.h struct dwc2_plat_otg_data { · line 32

Quoted 6 lines
include/usb/dwc2_udc.h +2 -0
@@ -27,4 +27,6 @@ struct dwc2_plat_otg_data {
 
 int dwc2_udc_probe(struct dwc2_plat_otg_data *pdata);
 
+int dwc2_udc_B_session_valid(struct udevice *dev);
+
 #endif	/* __DWC2_USB_GADGET */

Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de -------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190408/cebebc1c/attachment.sig>

#16 lore raw

PATCH 11/16 usb: dwc2_udc_otg: Read MAX_HW_ENDPOINT from HWCFG4 register

In reply to Patrick Delaunay

Some DWC2 ip variant doesn't use 16 hardware endpoint as hardcoded in the driver. Bits INEps [29:26] of HWCFG4 register allows to get this information.

---

 drivers/usb/gadget/dwc2_udc_otg.c      | 11 ++++++++---
 drivers/usb/gadget/dwc2_udc_otg_priv.h |  1 -
 drivers/usb/gadget/dwc2_udc_otg_regs.h | 17 ++++++++++++-----
 3 files changed, 20 insertions(+), 9 deletions(-)
drivers/usb/gadget/dwc2_udc_otg.c +8 -3
index b1efad1..5c7d131 100644
@@ -456,6 +456,7 @@ static void reconfig_usbd(struct dwc2_udc *dev)
 	unsigned int uTemp = writel(CORE_SOFT_RESET, &reg->grstctl);
 	uint32_t dflt_gusbcfg;
 	uint32_t rx_fifo_sz, tx_fifo_sz, np_tx_fifo_sz;
+	u32 max_hw_ep;
 
 	debug("Reseting OTG controller\n");
 
@@ -538,9 +539,13 @@ static void reconfig_usbd(struct dwc2_udc *dev)
 	writel((np_tx_fifo_sz << 16) | rx_fifo_sz,
 	       &reg->gnptxfsiz);
 
-	for (i = 1; i < DWC2_MAX_HW_ENDPOINTS; i++)
-		writel((rx_fifo_sz + np_tx_fifo_sz + tx_fifo_sz*(i-1)) |
-			tx_fifo_sz << 16, &reg->dieptxf[i-1]);
+	/* retrieve the number of IN Endpoints (excluding ep0) */
+	max_hw_ep = (readl(&reg->ghwcfg4) & GHWCFG4_NUM_IN_EPS_MASK) >>
+		    GHWCFG4_NUM_IN_EPS_SHIFT;
+
+	for (i = 0; i < max_hw_ep; i++)
+		writel((rx_fifo_sz + np_tx_fifo_sz + (tx_fifo_sz * i)) |
+			tx_fifo_sz << 16, &reg->dieptxf[i]);
 
 	/* Flush the RX FIFO */
 	writel(RX_FIFO_FLUSH, &reg->grstctl);
drivers/usb/gadget/dwc2_udc_otg_priv.h +0 -1
index aaa9018..e72b22a 100644
@@ -23,7 +23,6 @@
 #define EP_FIFO_SIZE2		1024
 /* ep0-control, ep1in-bulk, ep2out-bulk, ep3in-int */
 #define DWC2_MAX_ENDPOINTS	4
-#define DWC2_MAX_HW_ENDPOINTS	16
 
 #define WAIT_FOR_SETUP          0
 #define DATA_STATE_XMIT         1
drivers/usb/gadget/dwc2_udc_otg_regs.h +12 -5
index 0aee4ee..a389923 100644
@@ -60,22 +60,25 @@ struct dwc2_usbotg_reg {
 	u32 grxstsp; /* Receive Status Debug Pop/Status Pop */
 	u32 grxfsiz; /* Receive FIFO Size */
 	u32 gnptxfsiz; /* Non-Periodic Transmit FIFO Size */
-	u8  res1[216];
+
+	u8  res1[36];
+	u32 ghwcfg4; /* User HW Config4 */
+	u8  res2[176];
 	u32 dieptxf[15]; /* Device Periodic Transmit FIFO size register */
-	u8  res2[1728];
+	u8  res3[1728];
 	/* Device Configuration */
 	u32 dcfg; /* Device Configuration Register */
 	u32 dctl; /* Device Control */
 	u32 dsts; /* Device Status */
-	u8  res3[4];
+	u8  res4[4];
 	u32 diepmsk; /* Device IN Endpoint Common Interrupt Mask */
 	u32 doepmsk; /* Device OUT Endpoint Common Interrupt Mask */
 	u32 daint; /* Device All Endpoints Interrupt */
 	u32 daintmsk; /* Device All Endpoints Interrupt Mask */
-	u8  res4[224];
+	u8  res5[224];
 	struct dwc2_dev_in_endp in_endp[16];
 	struct dwc2_dev_out_endp out_endp[16];
-	u8  res5[768];
+	u8  res6[768];
 	struct ep_fifo ep[16];
 };
 
@@ -273,4 +276,8 @@ struct dwc2_usbotg_reg {
 /* Device ALL Endpoints Interrupt Register (DAINT) */
 #define DAINT_IN_EP_INT(x)                        (x << 0)
 #define DAINT_OUT_EP_INT(x)                       (x << 16)
+
+/* User HW Config4 */
+#define GHWCFG4_NUM_IN_EPS_MASK		(0xf << 26)
+#define GHWCFG4_NUM_IN_EPS_SHIFT	26
 #endif
Signature · 1 line
2.7.4
#17 lore raw

PATCH 11/16 usb: dwc2_udc_otg: Read MAX_HW_ENDPOINT from HWCFG4 register

Quoted 94 lines · On Fri, 29 Mar 2019 15:42:19 +0100 Patrick Delaunay <[email protected]>…

Some DWC2 ip variant doesn't use 16 hardware endpoint as hardcoded in the driver. Bits INEps [29:26] of HWCFG4 register allows to get this information.

---

 drivers/usb/gadget/dwc2_udc_otg.c      | 11 ++++++++---
 drivers/usb/gadget/dwc2_udc_otg_priv.h |  1 -
 drivers/usb/gadget/dwc2_udc_otg_regs.h | 17 ++++++++++++-----
 3 files changed, 20 insertions(+), 9 deletions(-)
(quoted diff) +0 -0

b/drivers/usb/gadget/dwc2_udc_otg.c index b1efad1..5c7d131 100644

drivers/usb/gadget/dwc2_udc_otg.c +1 -2
@@ -456,6 +456,7 @@ static void reconfig_usbd(struct dwc2_udc *dev)
 	unsigned int uTemp = writel(CORE_SOFT_RESET, &reg->grstctl);
 	uint32_t dflt_gusbcfg;
 	uint32_t rx_fifo_sz, tx_fifo_sz, np_tx_fifo_sz;
+	u32 max_hw_ep;
 
 	debug("Reseting OTG controller\n");
 
@@ -538,9 +539,13 @@ static void reconfig_usbd(struct dwc2_udc *dev)
 	writel((np_tx_fifo_sz << 16) | rx_fifo_sz,
 	       &reg->gnptxfsiz);
 
-	for (i = 1; i < DWC2_MAX_HW_ENDPOINTS; i++)
-		writel((rx_fifo_sz + np_tx_fifo_sz +

tx_fifo_sz*(i-1)) |

drivers/usb/gadget/dwc2_udc_otg.c +2 -1
-			tx_fifo_sz << 16, &reg->dieptxf[i-1]);
+	/* retrieve the number of IN Endpoints (excluding ep0) */
+	max_hw_ep = (readl(&reg->ghwcfg4) & GHWCFG4_NUM_IN_EPS_MASK)
Quoted 1 line
Quoted 1 line
drivers/usb/gadget/dwc2_udc_otg.c +4 -0
+		    GHWCFG4_NUM_IN_EPS_SHIFT;
+
+	for (i = 0; i < max_hw_ep; i++)
+		writel((rx_fifo_sz + np_tx_fifo_sz + (tx_fifo_sz *

i)) |

drivers/usb/gadget/dwc2_udc_otg.c +1 -0
+			tx_fifo_sz << 16, &reg->dieptxf[i]);
 
 	/* Flush the RX FIFO */
 	writel(RX_FIFO_FLUSH, &reg->grstctl);
(quoted diff) +0 -0

b/drivers/usb/gadget/dwc2_udc_otg_priv.h index aaa9018..e72b22a 100644

drivers/usb/gadget/dwc2_udc_otg_priv.h +0 -1
@@ -23,7 +23,6 @@
 #define EP_FIFO_SIZE2		1024
 /* ep0-control, ep1in-bulk, ep2out-bulk, ep3in-int */
 #define DWC2_MAX_ENDPOINTS	4
-#define DWC2_MAX_HW_ENDPOINTS	16
 
 #define WAIT_FOR_SETUP          0
 #define DATA_STATE_XMIT         1
(quoted diff) +0 -0

b/drivers/usb/gadget/dwc2_udc_otg_regs.h index 0aee4ee..a389923 100644

drivers/usb/gadget/dwc2_udc_otg_regs.h +4 -1
@@ -60,22 +60,25 @@ struct dwc2_usbotg_reg {
 	u32 grxstsp; /* Receive Status Debug Pop/Status Pop */
 	u32 grxfsiz; /* Receive FIFO Size */
 	u32 gnptxfsiz; /* Non-Periodic Transmit FIFO Size */
-	u8  res1[216];
+
+	u8  res1[36];
+	u32 ghwcfg4; /* User HW Config4 */
+	u8  res2[176];
 	u32 dieptxf[15]; /* Device Periodic Transmit FIFO size

register */

drivers/usb/gadget/dwc2_udc_otg_regs.h +4 -4
-	u8  res2[1728];
+	u8  res3[1728];
 	/* Device Configuration */
 	u32 dcfg; /* Device Configuration Register */
 	u32 dctl; /* Device Control */
 	u32 dsts; /* Device Status */
-	u8  res3[4];
+	u8  res4[4];
 	u32 diepmsk; /* Device IN Endpoint Common Interrupt Mask */
 	u32 doepmsk; /* Device OUT Endpoint Common Interrupt Mask */
 	u32 daint; /* Device All Endpoints Interrupt */
 	u32 daintmsk; /* Device All Endpoints Interrupt Mask */
-	u8  res4[224];
+	u8  res5[224];
 	struct dwc2_dev_in_endp in_endp[16];
 	struct dwc2_dev_out_endp out_endp[16];
-	u8  res5[768];
+	u8  res6[768];
 	struct ep_fifo ep[16];
 };

drivers/usb/gadget/dwc2_udc_otg_regs.h struct dwc2_usbotg_reg { · line 283

Quoted 8 lines
drivers/usb/gadget/dwc2_udc_otg_regs.h +4 -0
@@ -273,4 +276,8 @@ struct dwc2_usbotg_reg {
 /* Device ALL Endpoints Interrupt Register (DAINT) */
 #define DAINT_IN_EP_INT(x)                        (x << 0)
 #define DAINT_OUT_EP_INT(x)                       (x << 16)
+
+/* User HW Config4 */
+#define GHWCFG4_NUM_IN_EPS_MASK		(0xf << 26)
+#define GHWCFG4_NUM_IN_EPS_SHIFT	26
 #endif

Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de -------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190408/dfb54d83/attachment.sig>

#18 lore raw

PATCH 12/16 usb: dwc2_udc_otg: Add tx_fifo_sz array support

In reply to Patrick Delaunay

From: Patrice Chotard <[email protected]>

All TX fifo size can be different, add tx_fifo_sz_array[] into dwc2_plat_otg_data to be able to set them.

tx_fifo_sz_array[] is 17 Bytes long and can contains max 16 tx fifo size (synopsys IP supports max 16 IN endpoints). First entry of tx_fifo_sz_array[] is the number of valid fifo size the array contains.

In case of tx_fifo_sz_array[] doesn't contains the same number of element than max hardware endpoint, display a warning message.

Compatibility with board which doesn't use tx_fifo_sz_array[] (Rockchip rk322x/rk3128/rv1108/rk3288/rk3036) is kept.

---

 drivers/usb/gadget/dwc2_udc_otg.c | 14 ++++++++++++--
 include/usb/dwc2_udc.h            |  3 +++
 2 files changed, 15 insertions(+), 2 deletions(-)
drivers/usb/gadget/dwc2_udc_otg.c +12 -2
index 5c7d131..106dec5 100644
@@ -457,6 +457,7 @@ static void reconfig_usbd(struct dwc2_udc *dev)
 	uint32_t dflt_gusbcfg;
 	uint32_t rx_fifo_sz, tx_fifo_sz, np_tx_fifo_sz;
 	u32 max_hw_ep;
+	int pdata_hw_ep;
 
 	debug("Reseting OTG controller\n");
 
@@ -542,11 +543,20 @@ static void reconfig_usbd(struct dwc2_udc *dev)
 	/* retrieve the number of IN Endpoints (excluding ep0) */
 	max_hw_ep = (readl(&reg->ghwcfg4) & GHWCFG4_NUM_IN_EPS_MASK) >>
 		    GHWCFG4_NUM_IN_EPS_SHIFT;
+	pdata_hw_ep = dev->pdata->tx_fifo_sz_nb;
+
+	/* tx_fifo_sz_nb should equal to number of IN Endpoint */
+	if (pdata_hw_ep && max_hw_ep != pdata_hw_ep)
+		pr_warn("Got %d hw endpoint but %d tx-fifo-size in array !!\n",
+			max_hw_ep, pdata_hw_ep);
+
+	for (i = 0; i < max_hw_ep; i++) {
+		if (pdata_hw_ep)
+			tx_fifo_sz = dev->pdata->tx_fifo_sz_array[i];
 
-	for (i = 0; i < max_hw_ep; i++)
 		writel((rx_fifo_sz + np_tx_fifo_sz + (tx_fifo_sz * i)) |
 			tx_fifo_sz << 16, &reg->dieptxf[i]);
-
+	}
 	/* Flush the RX FIFO */
 	writel(RX_FIFO_FLUSH, &reg->grstctl);
 	while (readl(&reg->grstctl) & RX_FIFO_FLUSH)
include/usb/dwc2_udc.h +3 -0
index 8a426b6..369f6fb 100644
@@ -9,6 +9,7 @@
 #define __DWC2_USB_GADGET
 
 #define PHY0_SLEEP              (1 << 5)
+#define DWC2_MAX_HW_ENDPOINTS	16
 
 struct dwc2_plat_otg_data {
 	void		*priv;
@@ -22,6 +23,8 @@ struct dwc2_plat_otg_data {
 	unsigned int	rx_fifo_sz;
 	unsigned int	np_tx_fifo_sz;
 	unsigned int	tx_fifo_sz;
+	unsigned int	tx_fifo_sz_array[DWC2_MAX_HW_ENDPOINTS];
+	unsigned char   tx_fifo_sz_nb;
 	bool		force_b_session_valid;
 };
 
Signature · 1 line
2.7.4
#19 lore raw

PATCH 12/16 usb: dwc2_udc_otg: Add tx_fifo_sz array support

Quoted 74 lines · On Fri, 29 Mar 2019 15:42:20 +0100 Patrick Delaunay <[email protected]>…

From: Patrice Chotard <[email protected]>

All TX fifo size can be different, add tx_fifo_sz_array[] into dwc2_plat_otg_data to be able to set them.

tx_fifo_sz_array[] is 17 Bytes long and can contains max 16 tx fifo size (synopsys IP supports max 16 IN endpoints). First entry of tx_fifo_sz_array[] is the number of valid fifo size the array contains.

In case of tx_fifo_sz_array[] doesn't contains the same number of element than max hardware endpoint, display a warning message.

Compatibility with board which doesn't use tx_fifo_sz_array[] (Rockchip rk322x/rk3128/rv1108/rk3288/rk3036) is kept.

---

 drivers/usb/gadget/dwc2_udc_otg.c | 14 ++++++++++++--
 include/usb/dwc2_udc.h            |  3 +++
 2 files changed, 15 insertions(+), 2 deletions(-)
(quoted diff) +0 -0

b/drivers/usb/gadget/dwc2_udc_otg.c index 5c7d131..106dec5 100644

drivers/usb/gadget/dwc2_udc_otg.c +12 -2
@@ -457,6 +457,7 @@ static void reconfig_usbd(struct dwc2_udc *dev)
 	uint32_t dflt_gusbcfg;
 	uint32_t rx_fifo_sz, tx_fifo_sz, np_tx_fifo_sz;
 	u32 max_hw_ep;
+	int pdata_hw_ep;
 
 	debug("Reseting OTG controller\n");
 
@@ -542,11 +543,20 @@ static void reconfig_usbd(struct dwc2_udc *dev)
 	/* retrieve the number of IN Endpoints (excluding ep0) */
 	max_hw_ep = (readl(&reg->ghwcfg4) & GHWCFG4_NUM_IN_EPS_MASK)
 >> GHWCFG4_NUM_IN_EPS_SHIFT;
+	pdata_hw_ep = dev->pdata->tx_fifo_sz_nb;
+
+	/* tx_fifo_sz_nb should equal to number of IN Endpoint */
+	if (pdata_hw_ep && max_hw_ep != pdata_hw_ep)
+		pr_warn("Got %d hw endpoint but %d tx-fifo-size in
 array !!\n",
+			max_hw_ep, pdata_hw_ep);
+
+	for (i = 0; i < max_hw_ep; i++) {
+		if (pdata_hw_ep)
+			tx_fifo_sz = dev->pdata->tx_fifo_sz_array[i];
 
-	for (i = 0; i < max_hw_ep; i++)
 		writel((rx_fifo_sz + np_tx_fifo_sz + (tx_fifo_sz *
 i)) | tx_fifo_sz << 16, &reg->dieptxf[i]);
-
+	}
 	/* Flush the RX FIFO */
 	writel(RX_FIFO_FLUSH, &reg->grstctl);
drivers/usb/gadget/dwc2_udc_otg.c +0 -0
 	while (readl(&reg->grstctl) & RX_FIFO_FLUSH)
include/usb/dwc2_udc.h +1 -0
index 8a426b6..369f6fb 100644
@@ -9,6 +9,7 @@
 #define __DWC2_USB_GADGET
 
 #define PHY0_SLEEP              (1 << 5)
+#define DWC2_MAX_HW_ENDPOINTS	16
 
 struct dwc2_plat_otg_data {
 	void		*priv;

include/usb/dwc2_udc.h struct dwc2_plat_otg_data { · line 30

Quoted 8 lines
include/usb/dwc2_udc.h +2 -0
@@ -22,6 +23,8 @@ struct dwc2_plat_otg_data {
 	unsigned int	rx_fifo_sz;
 	unsigned int	np_tx_fifo_sz;
 	unsigned int	tx_fifo_sz;
+	unsigned int	tx_fifo_sz_array[DWC2_MAX_HW_ENDPOINTS];
+	unsigned char   tx_fifo_sz_nb;
 	bool		force_b_session_valid;
 };
 

Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de -------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190408/5e44c485/attachment.sig>

#20 lore raw

PATCH 13/16 usb: dwc2: add support for STM32MP1

In reply to Patrick Delaunay

Add compatible "st,stm32mp1-hsotg" and associated driver data to manage the usb33d-supply and the ST specific register for VBus sensing.

# Conflicts:
# drivers/usb/gadget/dwc2_udc_otg.c

---

 doc/device-tree-bindings/usb/dwc2.txt  |  2 ++
 drivers/usb/gadget/dwc2_udc_otg.c      | 45 ++++++++++++++++++++++++++++++++++
 drivers/usb/gadget/dwc2_udc_otg_regs.h | 10 ++++++--
 include/usb/dwc2_udc.h                 |  1 +
 4 files changed, 56 insertions(+), 2 deletions(-)
doc/device-tree-bindings/usb/dwc2.txt +2 -0
index 6dc3c4a..eb60ffa 100644
@@ -37,6 +37,8 @@ Refer to phy/phy-bindings.txt for generic phy consumer properties
 - g-rx-fifo-size: size of rx fifo size in gadget mode.
 - g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode.
 - g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode.
+- usb33d-supply: external VBUS and ID sensing comparators supply, in order to
+  perform OTG operation, used on STM32MP1 SoCs.
 
 Deprecated properties:
 - g-use-dma: gadget DMA mode is automatically detected
drivers/usb/gadget/dwc2_udc_otg.c +45 -0

78 lines not on this page · raw message

drivers/usb/gadget/dwc2_udc_otg_regs.h +8 -2
index a389923..b2a28d7 100644
@@ -60,8 +60,9 @@ struct dwc2_usbotg_reg {
 	u32 grxstsp; /* Receive Status Debug Pop/Status Pop */
 	u32 grxfsiz; /* Receive FIFO Size */
 	u32 gnptxfsiz; /* Non-Periodic Transmit FIFO Size */
-
-	u8  res1[36];
+	u8  res0[12];
+	u32 ggpio;     /* 0x038 */
+	u8  res1[20];
 	u32 ghwcfg4; /* User HW Config4 */
 	u8  res2[176];
 	u32 dieptxf[15]; /* Device Periodic Transmit FIFO size register */
@@ -280,4 +281,9 @@ struct dwc2_usbotg_reg {
 /* User HW Config4 */
 #define GHWCFG4_NUM_IN_EPS_MASK		(0xf << 26)
 #define GHWCFG4_NUM_IN_EPS_SHIFT	26
+
+/* OTG general core configuration register (OTG_GCCFG:0x38) for STM32MP1 */
+#define GGPIO_STM32_OTG_GCCFG_VBDEN               BIT(21)
+#define GGPIO_STM32_OTG_GCCFG_IDEN                BIT(22)
+
 #endif
include/usb/dwc2_udc.h +1 -0
index 369f6fb..a6c1221 100644
@@ -26,6 +26,7 @@ struct dwc2_plat_otg_data {
 	unsigned int	tx_fifo_sz_array[DWC2_MAX_HW_ENDPOINTS];
 	unsigned char   tx_fifo_sz_nb;
 	bool		force_b_session_valid;
+	bool		activate_stm_id_vb_detection;
 };
 
 int dwc2_udc_probe(struct dwc2_plat_otg_data *pdata);
Signature · 1 line
2.7.4
#21 lore raw

PATCH 13/16 usb: dwc2: add support for STM32MP1

Quoted 158 lines · On Fri, 29 Mar 2019 15:42:21 +0100 Patrick Delaunay <[email protected]>…

Add compatible "st,stm32mp1-hsotg" and associated driver data to manage the usb33d-supply and the ST specific register for VBus sensing.

# Conflicts:
# drivers/usb/gadget/dwc2_udc_otg.c

---

 doc/device-tree-bindings/usb/dwc2.txt  |  2 ++
 drivers/usb/gadget/dwc2_udc_otg.c      | 45

++++++++++++++++++++++++++++++++++
drivers/usb/gadget/dwc2_udc_otg_regs.h | 10 ++++++--
include/usb/dwc2_udc.h | 1 + 4 files changed, 56
insertions(+), 2 deletions(-)

(quoted diff) +0 -0

b/doc/device-tree-bindings/usb/dwc2.txt index 6dc3c4a..eb60ffa 100644

doc/device-tree-bindings/usb/dwc2.txt +0 -0
@@ -37,6 +37,8 @@ Refer to phy/phy-bindings.txt for generic phy

consumer properties
- g-rx-fifo-size: size of rx fifo size in gadget mode.
- g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget
mode.
- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0)
in gadget mode. +- usb33d-supply: external VBUS and ID sensing comparators supply, in order to

doc/device-tree-bindings/usb/dwc2.txt +1 -0
+  perform OTG operation, used on STM32MP1 SoCs.
 
 Deprecated properties:
 - g-use-dma: gadget DMA mode is automatically detected
(quoted diff) +0 -0

b/drivers/usb/gadget/dwc2_udc_otg.c index 106dec5..3fdaa10 100644

drivers/usb/gadget/dwc2_udc_otg.c +15 -0
@@ -942,6 +942,7 @@ struct dwc2_priv_data {
 	struct reset_ctl_bulk	resets;
 	struct phy *phys;
 	int num_phys;
+	struct udevice *usb33d_supply;
 };
 
 int dm_usb_gadget_handle_interrupts(struct udevice *dev)
@@ -1036,6 +1037,8 @@ static int
 dwc2_udc_otg_ofdata_to_platdata(struct udevice *dev) {
 	struct dwc2_plat_otg_data *platdata = dev_get_platdata(dev);
 	int node = dev_of_offset(dev);
+	ulong drvdata;
+	void (*set_params)(struct dwc2_plat_otg_data *data);
 
 	if (usb_get_dr_mode(node) != USB_DR_MODE_PERIPHERAL) {
 		dev_dbg(dev, "Invalid mode\n");
@@ -1052,9 +1055,28 @@ static int
 dwc2_udc_otg_ofdata_to_platdata(struct udevice *dev)
 platdata->force_b_session_valid = dev_read_bool(dev,
 "force-b-session-valid"); 
+	/* force platdata according compatible */
+	drvdata = dev_get_driver_data(dev);
+	if (drvdata) {
+		set_params = (void *)drvdata;
+		set_params(platdata);
+	}
+
 	return 0;
 }
 
+static void dwc2_set_stm32mp1_hsotg_params(struct dwc2_plat_otg_data
 *p) +{
+	p->activate_stm_id_vb_detection = true;
+	p->usb_gusbcfg =
+		0 << 15		/* PHY Low Power Clock sel*/
+		| 0x9 << 10	/* USB Turnaround time (0x9 for

HS phy) */

drivers/usb/gadget/dwc2_udc_otg.c +3 -0
+		| 0 << 9	/* [0:HNP disable,1:HNP enable]*/
+		| 0 << 8	/* [0:SRP disable 1:SRP enable]*/
+		| 0 << 6	/* 0: high speed utmi+, 1: full

speed serial*/

drivers/usb/gadget/dwc2_udc_otg.c +13 -0
+		| 0x7 << 0;	/* FS timeout calibration**/
+}
+
 static int dwc2_udc_otg_reset_init(struct udevice *dev,
 				   struct reset_ctl_bulk *resets)
 {
@@ -1122,6 +1144,26 @@ static int dwc2_udc_otg_probe(struct udevice
 *dev) if (ret)
 		return ret;
 
+	if (CONFIG_IS_ENABLED(DM_REGULATOR) &&
+	    platdata->activate_stm_id_vb_detection &&
+	    !platdata->force_b_session_valid) {
+		ret = device_get_supply_regulator(dev,
 "usb33d-supply",
+
 &priv->usb33d_supply);
+		if (ret) {
+			dev_err(dev, "can't get voltage level
 detector supply\n");
+			return ret;
+		}
+		ret = regulator_set_enable(priv->usb33d_supply,

true);

drivers/usb/gadget/dwc2_udc_otg.c +2 -0
+		if (ret) {
+			dev_err(dev, "can't enable voltage level

detector supply\n");

drivers/usb/gadget/dwc2_udc_otg.c +8 -0
+			return ret;
+		}
+		/* Enable vbus sensing */
+		setbits_le32(&usbotg_reg->ggpio,
+			     GGPIO_STM32_OTG_GCCFG_VBDEN |
+			     GGPIO_STM32_OTG_GCCFG_IDEN);
+	}
+
 	if (platdata->force_b_session_valid)
 		/* Override B session bits : value and enable */
 		setbits_le32(&usbotg_reg->gotgctl,  B_VALOEN |

B_VALOVAL); @@ -1154,6 +1196,9 @@ static int dwc2_udc_otg_remove(struct udevice *dev)
static const struct udevice_id dwc2_udc_otg_ids[] = {

drivers/usb/gadget/dwc2_udc_otg.c +3 -0
 	{ .compatible = "snps,dwc2" },
+	{ .compatible = "st,stm32mp1-hsotg",
+	  .data = (ulong)dwc2_set_stm32mp1_hsotg_params },
+	{},
 };
 
 U_BOOT_DRIVER(dwc2_udc_otg) = {
(quoted diff) +0 -0

b/drivers/usb/gadget/dwc2_udc_otg_regs.h index a389923..b2a28d7 100644

drivers/usb/gadget/dwc2_udc_otg_regs.h +3 -2
@@ -60,8 +60,9 @@ struct dwc2_usbotg_reg {
 	u32 grxstsp; /* Receive Status Debug Pop/Status Pop */
 	u32 grxfsiz; /* Receive FIFO Size */
 	u32 gnptxfsiz; /* Non-Periodic Transmit FIFO Size */
-
-	u8  res1[36];
+	u8  res0[12];
+	u32 ggpio;     /* 0x038 */
+	u8  res1[20];
 	u32 ghwcfg4; /* User HW Config4 */
 	u8  res2[176];
 	u32 dieptxf[15]; /* Device Periodic Transmit FIFO size

register */ @@ -280,4 +281,9 @@ struct dwc2_usbotg_reg {
/* User HW Config4 */
#define GHWCFG4_NUM_IN_EPS_MASK (0xf << 26)
#define GHWCFG4_NUM_IN_EPS_SHIFT 26

drivers/usb/gadget/dwc2_udc_otg_regs.h +2 -0
+
+/* OTG general core configuration register (OTG_GCCFG:0x38) for

STM32MP1 */ +#define GGPIO_STM32_OTG_GCCFG_VBDEN BIT(21)

drivers/usb/gadget/dwc2_udc_otg_regs.h +2 -0
+#define GGPIO_STM32_OTG_GCCFG_IDEN                BIT(22)
+
 #endif
include/usb/dwc2_udc.h +0 -0
index 369f6fb..a6c1221 100644

include/usb/dwc2_udc.h struct dwc2_plat_otg_data { · line 32

Quoted 7 lines
include/usb/dwc2_udc.h +1 -0
@@ -26,6 +26,7 @@ struct dwc2_plat_otg_data {
 	unsigned int	tx_fifo_sz_array[DWC2_MAX_HW_ENDPOINTS];
 	unsigned char   tx_fifo_sz_nb;
 	bool		force_b_session_valid;
+	bool		activate_stm_id_vb_detection;
 };
 
 int dwc2_udc_probe(struct dwc2_plat_otg_data *pdata);

Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de -------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190408/bb806eaf/attachment.sig>

#22 lore raw

PATCH 14/16 stm32mp1: remove CONFIG_USB_DWC2, HOST support for USBO

In reply to Patrick Delaunay

Remove the HOST support for STM32MP1 USBO device = OTG DWC2. The current DWC2 driver have no dynamic detection of device, So it is dangerous to have start 3V3 when PC is connected to the micro USB connector.

=> it is preferable to have only DEVICE support
CONFIG_USB_GADGET_DWC2_OTG for OTG port

See DWC3 driver for clean dual role support...

---

 configs/stm32mp15_basic_defconfig   | 1 -
 configs/stm32mp15_trusted_defconfig | 1 -
 2 files changed, 2 deletions(-)
configs/stm32mp15_basic_defconfig +0 -1
index c54dcfa..b6d994c 100644
@@ -73,7 +73,6 @@ CONFIG_USB=y
 CONFIG_DM_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_GENERIC=y
-CONFIG_USB_DWC2=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_GADGET_MANUFACTURER="STMicroelectronics"
 CONFIG_USB_GADGET_VENDOR_NUM=0x0483
configs/stm32mp15_trusted_defconfig +0 -1
index a050cee..ed2a2e6 100644
@@ -62,7 +62,6 @@ CONFIG_USB=y
 CONFIG_DM_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_GENERIC=y
-CONFIG_USB_DWC2=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_GADGET_MANUFACTURER="STMicroelectronics"
 CONFIG_USB_GADGET_VENDOR_NUM=0x0483
Signature · 1 line
2.7.4
#23 lore raw

PATCH 15/16 stm32mp1: migrate USBOTG device to driver model

In reply to Patrick Delaunay

Use the DWC2 device driver with DM_USB_GADGET support and cleanup the USB support in STM32MP1 board.

---

 arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi |   3 +-
 arch/arm/dts/stm32mp157a-dk1.dts         |  16 ++-
 arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi |   1 +
 arch/arm/dts/stm32mp157c.dtsi            |   2 +-
 board/st/stm32mp1/stm32mp1.c             | 165 +++----------------------------
 configs/stm32mp15_basic_defconfig        |   1 +
 configs/stm32mp15_trusted_defconfig      |   1 +
 7 files changed, 32 insertions(+), 157 deletions(-)
arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi +2 -1
index af7acfa..7e2c5d0 100644
@@ -11,6 +11,7 @@
 	aliases {
 		i2c3 = &i2c4;
 		mmc0 = &sdmmc1;
+		usb0 = &usbotg_hs;
 	};
 	config {
 		u-boot,boot-led = "heartbeat";
@@ -190,7 +191,7 @@
 };
 
 &usbotg_hs {
-	usb1600;
+	force-b-session-valid;
 	hnp-srp-disable;
 };
 
arch/arm/dts/stm32mp157a-dk1.dts +15 -1
index 0882765..b8ef820 100644
@@ -249,11 +249,25 @@
 	status = "okay";
 };
 
+&usbotg_hs {
+	dr_mode = "peripheral";
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
 &usbphyc {
-	vdd3v3-supply = <&vdd_usb>;
 	status = "okay";
 };
 
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
+
 &vrefbuf {
 	regulator-min-microvolt = <2500000>;
 	regulator-max-microvolt = <2500000>;
arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi +1 -0
index 6a18d03..6025b64 100644
@@ -12,6 +12,7 @@
 		i2c4 = &i2c5;
 		pinctrl2 = &stmfx_pinctrl;
 		spi0 = &qspi;
+		usb0 = &usbotg_hs;
 	};
 };
 
arch/arm/dts/stm32mp157c.dtsi +1 -1
index f1375a9..82177b5 100644
@@ -825,7 +825,7 @@
 		};
 
 		usbotg_hs: usb-otg at 49000000 {
-			compatible = "snps,dwc2";
+			compatible = "st,stm32mp1-hsotg", "snps,dwc2";
 			reg = <0x49000000 0x10000>;
 			clocks = <&rcc USBO_K>;
 			clock-names = "otg";
board/st/stm32mp1/stm32mp1.c +11 -154

205 lines not on this page · raw message

configs/stm32mp15_basic_defconfig +1 -0
index b6d994c..ff95dcd 100644
@@ -71,6 +71,7 @@ CONFIG_SERIAL_RX_BUFFER=y
 CONFIG_STM32_SERIAL=y
 CONFIG_USB=y
 CONFIG_DM_USB=y
+CONFIG_DM_USB_GADGET=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_GENERIC=y
 CONFIG_USB_GADGET=y
configs/stm32mp15_trusted_defconfig +1 -0
index ed2a2e6..f82b770 100644
@@ -60,6 +60,7 @@ CONFIG_SERIAL_RX_BUFFER=y
 CONFIG_STM32_SERIAL=y
 CONFIG_USB=y
 CONFIG_DM_USB=y
+CONFIG_DM_USB_GADGET=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_GENERIC=y
 CONFIG_USB_GADGET=y
Signature · 1 line
2.7.4
#24 lore raw

PATCH 16/16 stm32mp1: add stusb1600 support for DK1 and DK2 board

In reply to Patrick Delaunay

The DK1 and DK2 boards use the USB Type-C controller STUSB1600. This patch updates:
- the device tree to add the I2C node in the DT
- the board stm32mp1 to probe this I2C device and use this controller to check cable detection.
- the DWC2 driver to support a new dt property "u-boot,force-b-session-valid" which forces B session and device mode; it is a workaround because the VBUS sensing and ID detection isn't available with stusb1600.

---

 arch/arm/dts/stm32mp157-pinctrl.dtsi     |  7 ++++
 arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi |  2 +-
 arch/arm/dts/stm32mp157a-dk1.dts         | 18 ++++++++++
 board/st/stm32mp1/stm32mp1.c             | 56 ++++++++++++++++++++++++++++++++
 doc/device-tree-bindings/usb/dwc2.txt    |  2 ++
 drivers/usb/gadget/dwc2_udc_otg.c        |  8 +++--
 6 files changed, 90 insertions(+), 3 deletions(-)
arch/arm/dts/stm32mp157-pinctrl.dtsi +7 -0
index 867d244..1962267 100644
@@ -380,6 +380,13 @@
 				};
 			};
 
+			stusb1600_pins_a: stusb1600-0 {
+				pins {
+					pinmux = <STM32_PINMUX('I', 11, ANALOG)>;
+					bias-pull-up;
+				};
+			};
+
 			uart4_pins_a: uart4-0 {
 				pins1 {
 					pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi +1 -1
index 7e2c5d0..0f32a38 100644
@@ -191,7 +191,7 @@
 };
 
 &usbotg_hs {
-	force-b-session-valid;
+	u-boot,force-b-session-valid;
 	hnp-srp-disable;
 };
 
arch/arm/dts/stm32mp157a-dk1.dts +18 -0
index b8ef820..e36773d 100644
@@ -67,6 +67,24 @@
 	/delete-property/dmas;
 	/delete-property/dma-names;
 
+	typec: stusb1600 at 28 {
+		compatible = "st,stusb1600";
+		reg = <0x28>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpioi>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&stusb1600_pins_a>;
+
+		status = "okay";
+
+		typec_con: connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "sink";
+			power-opmode = "default";
+		};
+	};
+
 	pmic: stpmic at 33 {
 		compatible = "st,stpmic1";
 		reg = <0x33>;
board/st/stm32mp1/stm32mp1.c +56 -0

82 lines not on this page · raw message

doc/device-tree-bindings/usb/dwc2.txt +2 -0
index eb60ffa..61493f7 100644
@@ -39,6 +39,8 @@ Refer to phy/phy-bindings.txt for generic phy consumer properties
 - g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode.
 - usb33d-supply: external VBUS and ID sensing comparators supply, in order to
   perform OTG operation, used on STM32MP1 SoCs.
+- u-boot,force-b-session-valid: force B-peripheral session instead of relying on
+  VBUS sensing (only valid when dr_mode = "peripheral" and for u-boot).
 
 Deprecated properties:
 - g-use-dma: gadget DMA mode is automatically detected
drivers/usb/gadget/dwc2_udc_otg.c +6 -2
index 3fdaa10..494ab53 100644
@@ -1053,7 +1053,7 @@ static int dwc2_udc_otg_ofdata_to_platdata(struct udevice *dev)
 	platdata->tx_fifo_sz = dev_read_u32_default(dev, "g-tx-fifo-size", 0);
 
 	platdata->force_b_session_valid =
-		dev_read_bool(dev, "force-b-session-valid");
+		dev_read_bool(dev, "u-boot,force-b-session-valid");
 
 	/* force platdata according compatible */
 	drvdata = dev_get_driver_data(dev);
@@ -1075,6 +1075,9 @@ static void dwc2_set_stm32mp1_hsotg_params(struct dwc2_plat_otg_data *p)
 		| 0 << 8	/* [0:SRP disable 1:SRP enable]*/
 		| 0 << 6	/* 0: high speed utmi+, 1: full speed serial*/
 		| 0x7 << 0;	/* FS timeout calibration**/
+
+	if (p->force_b_session_valid)
+		p->usb_gusbcfg |= 1 << 30; /* FDMOD: Force device mode */
 }
 
 static int dwc2_udc_otg_reset_init(struct udevice *dev,
@@ -1166,7 +1169,8 @@ static int dwc2_udc_otg_probe(struct udevice *dev)
 
 	if (platdata->force_b_session_valid)
 		/* Override B session bits : value and enable */
-		setbits_le32(&usbotg_reg->gotgctl,  B_VALOEN | B_VALOVAL);
+		setbits_le32(&usbotg_reg->gotgctl,
+			     A_VALOEN | A_VALOVAL | B_VALOEN | B_VALOVAL);
 
 	ret = dwc2_udc_probe(platdata);
 	if (ret)
Signature · 1 line
2.7.4
#25 lore raw

PATCH 16/16 stm32mp1: add stusb1600 support for DK1 and DK2 board

Quoted 222 lines · On Fri, 29 Mar 2019 15:42:24 +0100 Patrick Delaunay <[email protected]>…

The DK1 and DK2 boards use the USB Type-C controller STUSB1600. This patch updates:
- the device tree to add the I2C node in the DT
- the board stm32mp1 to probe this I2C device and use this controller to check cable detection.
- the DWC2 driver to support a new dt property "u-boot,force-b-session-valid" which forces B session and device mode; it is a workaround because the VBUS sensing and ID detection isn't available with stusb1600.

---

 arch/arm/dts/stm32mp157-pinctrl.dtsi     |  7 ++++
 arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi |  2 +-
 arch/arm/dts/stm32mp157a-dk1.dts         | 18 ++++++++++
 board/st/stm32mp1/stm32mp1.c             | 56
++++++++++++++++++++++++++++++++
doc/device-tree-bindings/usb/dwc2.txt    |  2 ++
drivers/usb/gadget/dwc2_udc_otg.c        |  8 +++-- 6 files changed,

90 insertions(+), 3 deletions(-)

(quoted diff) +0 -0

b/arch/arm/dts/stm32mp157-pinctrl.dtsi index 867d244..1962267 100644

arch/arm/dts/stm32mp157-pinctrl.dtsi +7 -0
@@ -380,6 +380,13 @@
 				};
 			};
 
+			stusb1600_pins_a: stusb1600-0 {
+				pins {
+					pinmux = <STM32_PINMUX('I',
 11, ANALOG)>;
+					bias-pull-up;
+				};
+			};
+
 			uart4_pins_a: uart4-0 {
 				pins1 {

pinmux = <STM32_PINMUX('G',
11, AF6)>; /* UART4_TX */ diff --git a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi index 7e2c5d0..0f32a38 100644 --- a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi +++ b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi @@ -191,7 +191,7 @@
};

&usbotg_hs {

arch/arm/dts/stm32mp157-pinctrl.dtsi +1 -1
-	force-b-session-valid;
+	u-boot,force-b-session-valid;
 	hnp-srp-disable;
 };
(quoted diff) +0 -0

b/arch/arm/dts/stm32mp157a-dk1.dts index b8ef820..e36773d 100644

arch/arm/dts/stm32mp157a-dk1.dts +18 -0
@@ -67,6 +67,24 @@
 	/delete-property/dmas;
 	/delete-property/dma-names;
 
+	typec: stusb1600 at 28 {
+		compatible = "st,stusb1600";
+		reg = <0x28>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpioi>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&stusb1600_pins_a>;
+
+		status = "okay";
+
+		typec_con: connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "sink";
+			power-opmode = "default";
+		};
+	};
+
 	pmic: stpmic at 33 {
 		compatible = "st,stpmic1";
 		reg = <0x33>;
(quoted diff) +0 -0

b/board/st/stm32mp1/stm32mp1.c index 58b6d78..23737ce 100644

board/st/stm32mp1/stm32mp1.c +56 -0
@@ -9,15 +9,18 @@
 #include <dm.h>
 #include <g_dnl.h>
 #include <generic-phy.h>
+#include <i2c.h>
 #include <led.h>
 #include <misc.h>
 #include <phy.h>
 #include <reset.h>
 #include <syscon.h>
+#include <usb.h>
 #include <asm/io.h>
 #include <asm/gpio.h>
 #include <asm/arch/stm32.h>
 #include <power/regulator.h>
+#include <usb/dwc2_udc.h>
 
 /* SYSCFG registers */
 #define SYSCFG_BOOTR		0x00
@@ -151,11 +154,64 @@ static void board_key_check(void)
 
 #if defined(CONFIG_USB_GADGET) && defined(CONFIG_USB_GADGET_DWC2_OTG)
 
+/* STMicroelectronics STUSB1600 Type-C controller */
+#define STUSB1600_CC_CONNECTION_STATUS		0x0E
+
+/* STUSB1600_CC_CONNECTION_STATUS bitfields */
+#define STUSB1600_CC_ATTACH			BIT(0)
+
+static int stusb1600_init(struct udevice **dev_stusb1600)
+{
+	ofnode node;
+	struct udevice *dev, *bus;
+	int ret;
+	u32 chip_addr;
+
+	*dev_stusb1600 = NULL;
+
+	/* if node stusb1600 is present, means DK1 or DK2 board */
+	node = ofnode_by_compatible(ofnode_null(), "st,stusb1600");
+	if (!ofnode_valid(node))
+		return -ENODEV;
+
+	ret = ofnode_read_u32(node, "reg", &chip_addr);
+	if (ret)
+		return -EINVAL;
+
+	ret = uclass_get_device_by_ofnode(UCLASS_I2C,
 ofnode_get_parent(node),
+					  &bus);
+	if (ret) {
+		printf("bus for stusb1600 not found\n");
+		return -ENODEV;
+	}
+
+	ret = dm_i2c_probe(bus, chip_addr, 0, &dev);
+	if (!ret)
+		*dev_stusb1600 = dev;
+
+	return ret;
+}
+
+static int stusb1600_cable_connected(struct udevice *dev)
+{
+	u8 status;
+
+	if (dm_i2c_read(dev, STUSB1600_CC_CONNECTION_STATUS,
 &status, 1))
+		return 0;
+
+	return status & STUSB1600_CC_ATTACH;
+}
+
+#include <usb/dwc2_udc.h>
 int g_dnl_board_usb_cable_connected(void)
 {
+	struct udevice *stusb1600;
 	struct udevice *dwc2_udc_otg;
 	int ret;
 
+	if (!stusb1600_init(&stusb1600))
+		return stusb1600_cable_connected(stusb1600);
+
 	ret = uclass_get_device_by_driver(UCLASS_USB_GADGET_GENERIC,
board/st/stm32mp1/stm32mp1.c +0 -0
 					  DM_GET_DRIVER(dwc2_udc_otg),
 					  &dwc2_udc_otg);
(quoted diff) +0 -0

b/doc/device-tree-bindings/usb/dwc2.txt index eb60ffa..61493f7 100644

doc/device-tree-bindings/usb/dwc2.txt +0 -0
@@ -39,6 +39,8 @@ Refer to phy/phy-bindings.txt for generic phy

consumer properties
- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0)
in gadget mode.
- usb33d-supply: external VBUS and ID sensing comparators supply, in
order to perform OTG operation, used on STM32MP1 SoCs.
+- u-boot,force-b-session-valid: force B-peripheral session instead of relying on
+ VBUS sensing (only valid when dr_mode = "peripheral" and for u-boot).
Deprecated properties:
- g-use-dma: gadget DMA mode is automatically detected

(quoted diff) +0 -0

b/drivers/usb/gadget/dwc2_udc_otg.c index 3fdaa10..494ab53 100644

drivers/usb/gadget/dwc2_udc_otg.c +0 -0
@@ -1053,7 +1053,7 @@ static int
 dwc2_udc_otg_ofdata_to_platdata(struct udevice *dev)
 platdata->tx_fifo_sz = dev_read_u32_default(dev, "g-tx-fifo-size",

0); platdata->force_b_session_valid =

drivers/usb/gadget/dwc2_udc_otg.c +1 -1
-		dev_read_bool(dev, "force-b-session-valid");
+		dev_read_bool(dev, "u-boot,force-b-session-valid");
 
 	/* force platdata according compatible */
 	drvdata = dev_get_driver_data(dev);
@@ -1075,6 +1075,9 @@ static void

dwc2_set_stm32mp1_hsotg_params(struct dwc2_plat_otg_data *p) | 0 <<
8 /* [0:SRP disable 1:SRP enable]*/ | 0 << 6 /* 0: high
speed utmi+, 1: full speed serial*/ | 0x7 << 0; /* FS timeout
calibration**/ +

drivers/usb/gadget/dwc2_udc_otg.c +2 -0
+	if (p->force_b_session_valid)
+		p->usb_gusbcfg |= 1 << 30; /* FDMOD: Force device

mode */ }

static int dwc2_udc_otg_reset_init(struct udevice *dev,

drivers/usb/gadget/dwc2_udc_otg.c +2 -1
@@ -1166,7 +1169,8 @@ static int dwc2_udc_otg_probe(struct udevice
 *dev) 
 	if (platdata->force_b_session_valid)
 		/* Override B session bits : value and enable */
-		setbits_le32(&usbotg_reg->gotgctl,  B_VALOEN |
 B_VALOVAL);
+		setbits_le32(&usbotg_reg->gotgctl,
+			     A_VALOEN | A_VALOVAL | B_VALOEN |
 B_VALOVAL); 
 	ret = dwc2_udc_probe(platdata);
Quoted 1 line

if (ret)

Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de -------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190409/45bf1352/attachment.sig>

#26 lore raw

cover usb: convert dwc2 gadget to driver model, used in stm32mp1

In reply to Patrick Delaunay
Quoted 8 lines · Patrick Delaunay

This patch-set created after Marek remarks on patch
board: stm32mp1: Add tx_fifo_sz_array support
http://patchwork.ozlabs.org/patch/1056452/

This serie convert the DWC2 to driver model and use it for the stm32mp1 boards.

Quoted 8 lines

USB device and cable connection tested on EV1 and DK2.

This serie superseded the Patrice patches:
http://patchwork.ozlabs.org/project/uboot/list/?series=97121

Warning: the serie need to be apply after
http://patchwork.ozlabs.org/project/uboot/list/?series=91422
http://patchwork.ozlabs.org/project/uboot/list/?series=91497

Hi Patrice,

The second patch series doesn't apply cleanly anymore, could you rebase and resend so I can test this series?

Regards,
Jack.

Quoted 42 lines

Patrice Chotard (1):
usb: dwc2_udc_otg: Add tx_fifo_sz array support

Patrick Delaunay (15):
phy: usbphyc: remove unused variable index
phy: usbphyc: update xlate with DT binding
phy: usbphyc: Binding update of vdda supply
phy: usbphyc: move vdda1v1 and vdda1v8 in phy_init
phy: usbphyc: increase PLL wait timeout
usb: dwc2: remove unused variable regs_otg
usb: dwc2: convert driver to DM_USB_GADGET
usb: dwc2: force reset assert before to probe the driver
usb: dwc2: Add force-b-session-valid support
usb: dwc2: Add function for session B check
usb: dwc2_udc_otg: Read MAX_HW_ENDPOINT from HWCFG4 register
usb: dwc2: add support for STM32MP1
stm32mp1: remove CONFIG_USB_DWC2, HOST support for USBO
stm32mp1: migrate USBOTG device to driver model
stm32mp1: add stusb1600 support for DK1 and DK2 board

 arch/arm/dts/stm32mp157-pinctrl.dtsi               |   7 +
 arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi           |   3 +-
 arch/arm/dts/stm32mp157a-dk1.dts                   |  34 +-
 arch/arm/dts/stm32mp157c-ed1.dts                   |   8 -
 arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi           |   1 +
 arch/arm/dts/stm32mp157c.dtsi                      |   5 +-
 board/st/stm32mp1/stm32mp1.c                       | 185 +++-------
 configs/stm32mp15_basic_defconfig                  |   2 +-
 configs/stm32mp15_trusted_defconfig                |   2 +-
 doc/device-tree-bindings/phy/phy-stm32-usbphyc.txt |   4 +-
 doc/device-tree-bindings/usb/dwc2.txt              |  58 +++
 drivers/phy/phy-stm32-usbphyc.c                    | 111 +++---
 drivers/usb/gadget/dwc2_udc_otg.c                  | 388 ++++++++++++++++++++-
 drivers/usb/gadget/dwc2_udc_otg_priv.h             |   1 -
 drivers/usb/gadget/dwc2_udc_otg_regs.h             |  31 +-
 include/usb/dwc2_udc.h                             |   7 +
 16 files changed, 627 insertions(+), 220 deletions(-)
 create mode 100644 doc/device-tree-bindings/usb/dwc2.txt
#27 lore raw

cover usb: convert dwc2 gadget to driver model, used in stm32mp1

Quoted 18 lines

From: Jack Mitchell <[email protected]>
Sent: samedi 30 mars 2019 12:42

Quoted 13 lines · Patrick Delaunay

This patch-set created after Marek remarks on patch
board: stm32mp1: Add tx_fifo_sz_array support
http://patchwork.ozlabs.org/patch/1056452/

This serie convert the DWC2 to driver model and use it for the stm32mp1 boards.

USB device and cable connection tested on EV1 and DK2.

This serie superseded the Patrice patches:
http://patchwork.ozlabs.org/project/uboot/list/?series=97121

Quoted 8 lines
Quoted 3 lines

Warning: the serie need to be apply after
http://patchwork.ozlabs.org/project/uboot/list/?series=91422
http://patchwork.ozlabs.org/project/uboot/list/?series=91497

Hi Patrice,

The second patch series doesn't apply cleanly anymore, could you rebase and resend so I can test this series?

Hi,
Yes, I have many pending series for the next releases on stm32mp1 arch and for the 2 baord ev1 and dk2. So many conflicts.

I willl push a rebase this week,
but you can use my downstream branch (based on v2019.04) with all the upstreamed patches, including the last one for USB; I have already solve the issues:

https://github.com/patrickdelaunay/u-boot/tree/v2019.04-stm32mp

Quoted 2 lines

Regards,
Jack.

Patrick

Quoted 43 lines
Quoted 23 lines

Patrice Chotard (1):
usb: dwc2_udc_otg: Add tx_fifo_sz array support

Patrick Delaunay (15):
phy: usbphyc: remove unused variable index
phy: usbphyc: update xlate with DT binding
phy: usbphyc: Binding update of vdda supply
phy: usbphyc: move vdda1v1 and vdda1v8 in phy_init
phy: usbphyc: increase PLL wait timeout
usb: dwc2: remove unused variable regs_otg
usb: dwc2: convert driver to DM_USB_GADGET
usb: dwc2: force reset assert before to probe the driver
usb: dwc2: Add force-b-session-valid support
usb: dwc2: Add function for session B check
usb: dwc2_udc_otg: Read MAX_HW_ENDPOINT from HWCFG4 register
usb: dwc2: add support for STM32MP1
stm32mp1: remove CONFIG_USB_DWC2, HOST support for USBO
stm32mp1: migrate USBOTG device to driver model
stm32mp1: add stusb1600 support for DK1 and DK2 board

Quoted 13 lines
 arch/arm/dts/stm32mp157-pinctrl.dtsi               |   7 +
 arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi           |   3 +-
 arch/arm/dts/stm32mp157a-dk1.dts                   |  34 +-
 arch/arm/dts/stm32mp157c-ed1.dts                   |   8 -
 arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi           |   1 +
 arch/arm/dts/stm32mp157c.dtsi                      |   5 +-
 board/st/stm32mp1/stm32mp1.c                       | 185 +++-------
 configs/stm32mp15_basic_defconfig                  |   2 +-
 configs/stm32mp15_trusted_defconfig                |   2 +-
 doc/device-tree-bindings/phy/phy-stm32-usbphyc.txt |   4 +-
 doc/device-tree-bindings/usb/dwc2.txt              |  58 +++
 drivers/phy/phy-stm32-usbphyc.c                    | 111 +++---
 drivers/usb/gadget/dwc2_udc_otg.c                  | 388

++++++++++++++++++++-

Quoted 6 lines
 drivers/usb/gadget/dwc2_udc_otg_priv.h             |   1 -
 drivers/usb/gadget/dwc2_udc_otg_regs.h             |  31 +-
 include/usb/dwc2_udc.h                             |   7 +
 16 files changed, 627 insertions(+), 220 deletions(-)  create mode

100644 doc/device-tree-bindings/usb/dwc2.txt

#28 lore raw

cover usb: convert dwc2 gadget to driver model, used in stm32mp1

Quoted 27 lines · Patrick DELAUNAY
Quoted 16 lines

From: Jack Mitchell <[email protected]>
Sent: samedi 30 mars 2019 12:42

Quoted 12 lines · Patrick Delaunay

This patch-set created after Marek remarks on patch
board: stm32mp1: Add tx_fifo_sz_array support
http://patchwork.ozlabs.org/patch/1056452/

This serie convert the DWC2 to driver model and use it for the stm32mp1 boards.

USB device and cable connection tested on EV1 and DK2.

This serie superseded the Patrice patches:
http://patchwork.ozlabs.org/project/uboot/list/?series=97121

Quoted 7 lines
Quoted 3 lines

Warning: the serie need to be apply after
http://patchwork.ozlabs.org/project/uboot/list/?series=91422
http://patchwork.ozlabs.org/project/uboot/list/?series=91497

Hi Patrice,

The second patch series doesn't apply cleanly anymore, could you rebase and resend so I can test this series?

Hi,
Yes, I have many pending series for the next releases on stm32mp1 arch and for the 2 baord ev1 and dk2. So many conflicts.

Quoted 6 lines

I willl push a rebase this week,
but you can use my downstream branch (based on v2019.04) with all the upstreamed patches, including the last one for USB; I have already solve the issues:

https://github.com/patrickdelaunay/u-boot/tree/v2019.04-stm32mp

Thanks Patrick (and apologies for the previous wrong name), the reason I ask is I'm testing an rk3288 with the DM_USB_GADGET support enabled for it's dwc2 OTG controller. The controller still works without DM_USB_GADGET enabled, but it fails to enumerate any USB devices when it is enabled. Is there anything specific required apart from enabling DM_USB_GADGET?

=> usb start
starting USB...
scan end
No controllers found
=>

Quoted 48 lines
Quoted 4 lines

Regards,
Jack.

Patrick

Quoted 42 lines
Quoted 22 lines

Patrice Chotard (1):
usb: dwc2_udc_otg: Add tx_fifo_sz array support

Patrick Delaunay (15):
phy: usbphyc: remove unused variable index
phy: usbphyc: update xlate with DT binding
phy: usbphyc: Binding update of vdda supply
phy: usbphyc: move vdda1v1 and vdda1v8 in phy_init
phy: usbphyc: increase PLL wait timeout
usb: dwc2: remove unused variable regs_otg
usb: dwc2: convert driver to DM_USB_GADGET
usb: dwc2: force reset assert before to probe the driver
usb: dwc2: Add force-b-session-valid support
usb: dwc2: Add function for session B check
usb: dwc2_udc_otg: Read MAX_HW_ENDPOINT from HWCFG4 register
usb: dwc2: add support for STM32MP1
stm32mp1: remove CONFIG_USB_DWC2, HOST support for USBO
stm32mp1: migrate USBOTG device to driver model
stm32mp1: add stusb1600 support for DK1 and DK2 board

Quoted 13 lines
 arch/arm/dts/stm32mp157-pinctrl.dtsi               |   7 +
 arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi           |   3 +-
 arch/arm/dts/stm32mp157a-dk1.dts                   |  34 +-
 arch/arm/dts/stm32mp157c-ed1.dts                   |   8 -
 arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi           |   1 +
 arch/arm/dts/stm32mp157c.dtsi                      |   5 +-
 board/st/stm32mp1/stm32mp1.c                       | 185 +++-------
 configs/stm32mp15_basic_defconfig                  |   2 +-
 configs/stm32mp15_trusted_defconfig                |   2 +-
 doc/device-tree-bindings/phy/phy-stm32-usbphyc.txt |   4 +-
 doc/device-tree-bindings/usb/dwc2.txt              |  58 +++
 drivers/phy/phy-stm32-usbphyc.c                    | 111 +++---
 drivers/usb/gadget/dwc2_udc_otg.c                  | 388

++++++++++++++++++++-

Quoted 6 lines
 drivers/usb/gadget/dwc2_udc_otg_priv.h             |   1 -
 drivers/usb/gadget/dwc2_udc_otg_regs.h             |  31 +-
 include/usb/dwc2_udc.h                             |   7 +
 16 files changed, 627 insertions(+), 220 deletions(-)  create mode

100644 doc/device-tree-bindings/usb/dwc2.txt

#29 lore raw

cover usb: convert dwc2 gadget to driver model, used in stm32mp1

Hi,

Quoted 33 lines

From: Jack Mitchell <[email protected]>
Sent: lundi 1 avril 2019 12:38

Quoted 19 lines · Patrick DELAUNAY
Quoted 19 lines

From: Jack Mitchell <[email protected]>
Sent: samedi 30 mars 2019 12:42

Quoted 15 lines · Patrick Delaunay

This patch-set created after Marek remarks on patch
board: stm32mp1: Add tx_fifo_sz_array support
http://patchwork.ozlabs.org/patch/1056452/

This serie convert the DWC2 to driver model and use it for the stm32mp1 boards.

USB device and cable connection tested on EV1 and DK2.

This serie superseded the Patrice patches:
http://patchwork.ozlabs.org/project/uboot/list/?series=97121

Warning: the serie need to be apply after
http://patchwork.ozlabs.org/project/uboot/list/?series=91422
http://patchwork.ozlabs.org/project/uboot/list/?series=91497

Quoted 6 lines
Quoted 4 lines

Hi Patrice,

The second patch series doesn't apply cleanly anymore, could you rebase and resend so I can test this series?

Hi,
Yes, I have many pending series for the next releases on stm32mp1 arch and

for the 2 baord ev1 and dk2.

Quoted 2 lines

So many conflicts.

Quoted 8 lines
Quoted 6 lines

I willl push a rebase this week,
but you can use my downstream branch (based on v2019.04) with all the upstreamed patches, including the last one for USB; I have already solve the issues:

https://github.com/patrickdelaunay/u-boot/tree/v2019.04-stm32mp

Thanks Patrick (and apologies for the previous wrong name),

:-)

Quoted 11 lines

the reason I ask is
I'm testing an rk3288 with the DM_USB_GADGET support enabled for it's dwc2 OTG controller. The controller still works without DM_USB_GADGET enabled, but it fails to enumerate any USB devices when it is enabled. Is there anything specific required apart from enabling DM_USB_GADGET?

=> usb start
starting USB...
scan end
No controllers found
=>

I just add CONFIG_DM_USB_GADGET

But I also need to add a alias "usb0"

arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi

/ {
	aliases {
		gpio26 = &stmfx_pinctrl;
		i2c1 = &i2c2;
		i2c4 = &i2c5;
		pinctrl2 = &stmfx_pinctrl;
		spi0 = &qspi;
+		usb0 = &usbotg_hs;
	};
};

The alias 'usb0" is needed to selecte the correct sed number

drivers/usb/gadget/udc/udc-uclass.c

int usb_gadget_initialize(int index)

	udc-uclass.c:	ret = uclass_get_device_by_seq(UCLASS_USB_GADGET_GENERIC, index, &dev);

I spent some time to found it.

PS: sequence number is defined by alias in UCLASS :

UCLASS_DRIVER(usb_gadget_generic) = {
	.id		= UCLASS_USB_GADGET_GENERIC,
	.name		= "usb",
	.flags		= DM_UC_FLAG_SEQ_ALIAS,
};

Regards
Patrick