Skip to contentSkip to conversation

can: m_can: implement errata "Needless activation of MRAF irq"

PATCH RESEND Superseded [email protected] 2 participants 2 messages Apr 2, 2019 – Apr 25, 2019

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH RESEND 1/1 can: m_can: implement errata "Needless activation of MRAF irq"

From: Eugen Hristev <[email protected]>

During frame reception while the MCAN is in Error Passive state and the Receive Error Counter has thevalue MCAN_ECR.REC = 127, it may happen that MCAN_IR.MRAF is set although there was no Message RAM access failure. If MCAN_IR.MRAF is enabled, an interrupt to the Host CPU is generated. Work around:
The Message RAM Access Failure interrupt routine needs to check whether
MCAN_ECR.RP = '1' and MCAN_ECR.REC = '127'.
In this case, reset MCAN_IR.MRAF. No further action is required. This affects versions older than 3.2.0

Errata explained on Sama5d2 SoC which includes this hardware block:
http://ww1.microchip.com/downloads/en/DeviceDoc/SAMA5D2-Family-Silicon-Errata-and-Data-Sheet-Clarification-DS80000803B.pdf chapter 6.2

Reproducibility: If 2 devices with m_can are connected back to back, configuring different bitrate on them will lead to interrupt storm on the receiving side, with error "Message RAM access failure occurred". Another way is to have a bad hardware connection. Bad wire connection can lead to this issue as well.

This patch fixes the issue according to provided workaround.

---
 drivers/net/can/m_can/m_can.c | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)
drivers/net/can/m_can/m_can.c +21 -0
index 9b44940..deb274a 100644
@@ -822,6 +822,27 @@ static int m_can_poll(struct napi_struct *napi, int quota)
 	if (!irqstatus)
 		goto end;
 
+	/* Errata workaround for issue "Needless activation of MRAF irq"
+	 * During frame reception while the MCAN is in Error Passive state
+	 * and the Receive Error Counter has the value MCAN_ECR.REC = 127,
+	 * it may happen that MCAN_IR.MRAF is set although there was no
+	 * Message RAM access failure.
+	 * If MCAN_IR.MRAF is enabled, an interrupt to the Host CPU is generated
+	 * The Message RAM Access Failure interrupt routine needs to check
+	 * whether MCAN_ECR.RP = ’1’ and MCAN_ECR.REC = 127.
+	 * In this case, reset MCAN_IR.MRAF. No further action is required.
+	 */
+	if ((priv->version <= 31) && (irqstatus & IR_MRAF) &&
+	    (m_can_read(priv, M_CAN_ECR) & ECR_RP)) {
+		struct can_berr_counter bec;
+
+		__m_can_get_berr_counter(dev, &bec);
+		if (bec.rxerr == 127) {
+			m_can_write(priv, M_CAN_IR, IR_MRAF);
+			irqstatus &= ~IR_MRAF;
+		}
+	}
+
 	psr = m_can_read(priv, M_CAN_PSR);
 	if (irqstatus & IR_ERR_STATE)
 		work_done += m_can_handle_state_errors(dev, psr);
Signature · 1 line
2.7.4
Reviewed-by on v1 1/1
#1 lore raw
Quoted 22 lines · On Tue, Apr 02, 2019 at 12:56:18PM +0000, [email protected] wrote:

From: Eugen Hristev <[email protected]>

During frame reception while the MCAN is in Error Passive state and the Receive Error Counter has thevalue MCAN_ECR.REC = 127, it may happen that MCAN_IR.MRAF is set although there was no Message RAM access failure. If MCAN_IR.MRAF is enabled, an interrupt to the Host CPU is generated. Work around:
The Message RAM Access Failure interrupt routine needs to check whether
MCAN_ECR.RP = '1' and MCAN_ECR.REC = '127'.
In this case, reset MCAN_IR.MRAF. No further action is required. This affects versions older than 3.2.0

Errata explained on Sama5d2 SoC which includes this hardware block:
http://ww1.microchip.com/downloads/en/DeviceDoc/SAMA5D2-Family-Silicon-Errata-and-Data-Sheet-Clarification-DS80000803B.pdf chapter 6.2

Reproducibility: If 2 devices with m_can are connected back to back, configuring different bitrate on them will lead to interrupt storm on the receiving side, with error "Message RAM access failure occurred". Another way is to have a bad hardware connection. Bad wire connection can lead to this issue as well.

Quoted 3 lines

This patch fixes the issue according to provided workaround.

Sounds good.

Quoted 43 lines
---
 drivers/net/can/m_can/m_can.c | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)
drivers/net/can/m_can/m_can.c +21 -0
index 9b44940..deb274a 100644
@@ -822,6 +822,27 @@ static int m_can_poll(struct napi_struct *napi, int quota)
 	if (!irqstatus)
 		goto end;
 
+	/* Errata workaround for issue "Needless activation of MRAF irq"
+	 * During frame reception while the MCAN is in Error Passive state
+	 * and the Receive Error Counter has the value MCAN_ECR.REC = 127,
+	 * it may happen that MCAN_IR.MRAF is set although there was no
+	 * Message RAM access failure.
+	 * If MCAN_IR.MRAF is enabled, an interrupt to the Host CPU is generated
+	 * The Message RAM Access Failure interrupt routine needs to check
+	 * whether MCAN_ECR.RP = ’1’ and MCAN_ECR.REC = 127.
+	 * In this case, reset MCAN_IR.MRAF. No further action is required.
+	 */
+	if ((priv->version <= 31) && (irqstatus & IR_MRAF) &&
+	    (m_can_read(priv, M_CAN_ECR) & ECR_RP)) {
+		struct can_berr_counter bec;
+
+		__m_can_get_berr_counter(dev, &bec);
+		if (bec.rxerr == 127) {
+			m_can_write(priv, M_CAN_IR, IR_MRAF);
+			irqstatus &= ~IR_MRAF;
+		}
+	}
+
 	psr = m_can_read(priv, M_CAN_PSR);
 	if (irqstatus & IR_ERR_STATE)
 		work_done += m_can_handle_state_errors(dev, psr);
Signature · 6 lines
2.7.4

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel