Skip to contentSkip to conversation

run-postinsts: Fix full execution of scripts at first boot

PATCH In review Alejandro Enedino Hernandez Samaniego 2 participants 2 messages Apr 20, 2019 – Apr 26, 2019

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 run-postinsts: Fix full execution of scripts at first boot

run-postinsts runs a given set of scripts during the first boot of the device, when one of these scripts prints something to stdout (isnt daemonized correctly), since stdout is not available at that time, the script execution immediately returns with an error (exit_group()), this error causes the script to terminate all threads within the process, causing undesired behavior since the script might still had to execute some other code.

Replace eval built-in with $(), since $() executes in a different shell, even if one of the scripts exits, all threads of that process will only be within that session, this ensures other scripts meant to be run are still run afterwards.

This was only required on the line that actually executes the scripts:
"eval sh -c $i $append_log", other replacements were put for consistency, and generally, it is recommended to use $() instead of eval anyway.

[YOCTO #13266]

---
 .../recipes-devtools/run-postinsts/run-postinsts/run-postinsts | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
meta/recipes-devtools/run-postinsts/run-postinsts/run-postinsts +5 -5
index 95eff04..419796f 100755
@@ -65,13 +65,13 @@ exec_postinst_scriptlets() {
 	for i in `ls $pi_dir`; do
 		i=$pi_dir/$i
 		echo "Running postinst $i..."
-		[ "$POSTINST_LOGGING" = "1" ] && eval echo "Running postinst $i..." $append_log
+		[ "$POSTINST_LOGGING" = "1" ] && $(echo "Running postinst $i..." $append_log)
 		if [ -x $i ]; then
-			eval sh -c $i $append_log
+			$(sh -c $i $append_log)
 			rm $i
 		else
 			echo "ERROR: postinst $i failed."
-			[ "$POSTINST_LOGGING" = "1" ] && eval echo "ERROR: postinst $i failed." $append_log
+			[ "$POSTINST_LOGGING" = "1" ] && $(echo "ERROR: postinst $i failed." $append_log)
 			remove_pi_dir=0
 		fi
 	done
@@ -81,11 +81,11 @@ remove_pi_dir=1
 if $pm_installed; then
 	case $pm in
 		"ipk")
-			eval opkg configure $append_log
+			$(opkg configure $append_log)
 			;;
 
 		"deb")
-			eval dpkg --configure -a $append_log
+			$(dpkg --configure -a $append_log)
 			;;
 	esac
 else
Signature · 1 line
2.7.4
#1 lore raw
Quoted 26 lines · Alejandro Enedino Hernandez Samaniego

run-postinsts runs a given set of scripts during the first boot of the
device, when one of these scripts prints something to stdout (isnt daemonized correctly), since stdout is not available at that time, the script execution immediately returns with an error (exit_group()),
this error causes the script to terminate all threads within the process,
causing undesired behavior since the script might still had to execute
some other code.

Replace eval built-in with $(), since $() executes in a different shell,
even if one of the scripts exits, all threads of that process will only
be within that session, this ensures other scripts meant to be run are
still run afterwards.

This was only required on the line that actually executes the scripts:
"eval sh -c $i $append_log", other replacements were put for consistency,
and generally, it is recommended to use $() instead of eval anyway.

Quoted 4 lines

[YOCTO #13266]

Signed-off-by: Alejandro Enedino Hernandez Samaniego < [email protected]>

This seems to cause:

oe-selftest -r runtime_test.Postinst.test_postinst_rootfs_and_boot

to fail:

https://autobuilder.yoctoproject.org/typhoon/#/builders/56/builds/429

(both on the autobuilder and locally)

Cheers,

Richard