media: i2c: ov5645: Fix power sequence

PATCH Superseded Ezequiel Garcia 3 participants 4 messages Jul 10, 2019 – Jul 31, 2019

Subsystems (2)

Media (V4L/DVB) V4L2 camera sensor drivers

lore

Share & tools

lore

Ezequiel Garcia

author

2019-07-10 18:40 UTC #0 lore raw

PATCH v2 1/1 media: i2c: ov5645: Fix power sequence

This is mostly a port of Jacopo's fix:

commit aa4bb8b8838ffcc776a79f49a4d7476b82405349
Author: Jacopo Mondi <[email protected]>
Date: Fri Jul 6 05:51:52 2018 -0400

media: ov5640: Re-work MIPI startup sequence

In the OV5645 case, the changes are:

- Move OV5645_IO_MIPI_CTRL00 (0x300e) out of the initial setting blob.
- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
- At set_power(0) time power down MIPI Tx/Rx (in addition to the current power down of regulators and clock gating).
- At s_stream time enable/disable the MIPI interface output.

With this commit the sensor is able to enter LP-11 mode during power up, as expected by some CSI-2 controllers.

Many thanks to Fabio Estevam for his help debugging this issue.

Tested-by Fabio Estevam <[email protected]>

Signed-off-by Ezequiel Garcia <[email protected]>

---
Changes in v2:
* As suggested by Philipp, move the initial configuration to the ov5645_global_init_setting array.

---
 drivers/media/i2c/ov5645.c | 26 ++++++++++++++++++--------
 1 file changed, 18 insertions(+), 8 deletions(-)

drivers/media/i2c/ov5645.c +18 -8

index 124c8df04633..58972c884705 100644
@@ -45,6 +45,8 @@
 #define		OV5645_CHIP_ID_HIGH_BYTE	0x56
 #define OV5645_CHIP_ID_LOW		0x300b
 #define		OV5645_CHIP_ID_LOW_BYTE		0x45
+#define OV5645_IO_MIPI_CTRL00		0x300e
+#define OV5645_PAD_OUTPUT00		0x3019
 #define OV5645_AWB_MANUAL_CONTROL	0x3406
 #define		OV5645_AWB_MANUAL_ENABLE	BIT(0)
 #define OV5645_AEC_PK_MANUAL		0x3503

@@ -55,6 +57,7 @@
 #define		OV5645_ISP_VFLIP		BIT(2)
 #define OV5645_TIMING_TC_REG21		0x3821
 #define		OV5645_SENSOR_MIRROR		BIT(1)
+#define OV5645_MIPI_CTRL00		0x4800
 #define OV5645_PRE_ISP_TEST_SETTING_1	0x503d
 #define		OV5645_TEST_PATTERN_MASK	0x3
 #define		OV5645_SET_TEST_PATTERN(x)	((x) & OV5645_TEST_PATTERN_MASK)

@@ -121,7 +124,6 @@ static const struct reg_value ov5645_global_init_setting[] = {
 	{ 0x3503, 0x07 },
 	{ 0x3002, 0x1c },
 	{ 0x3006, 0xc3 },
-	{ 0x300e, 0x45 },
 	{ 0x3017, 0x00 },
 	{ 0x3018, 0x00 },
 	{ 0x302e, 0x0b },

@@ -350,7 +352,10 @@ static const struct reg_value ov5645_global_init_setting[] = {
 	{ 0x3a1f, 0x14 },
 	{ 0x0601, 0x02 },
 	{ 0x3008, 0x42 },
-	{ 0x3008, 0x02 }
+	{ 0x3008, 0x02 },
+	{ OV5645_IO_MIPI_CTRL00, 0x40 },
+	{ OV5645_MIPI_CTRL00, 0x24 },
+	{ OV5645_PAD_OUTPUT00, 0x70 }
 };
 
 static const struct reg_value ov5645_setting_sxga[] = {

@@ -737,13 +742,9 @@ static int ov5645_s_power(struct v4l2_subdev *sd, int on)
 				goto exit;
 			}
 
-			ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0,
-					       OV5645_SYSTEM_CTRL0_STOP);
-			if (ret < 0) {
-				ov5645_set_power_off(ov5645);
-				goto exit;
-			}
+			usleep_range(500, 1000);
 		} else {
+			ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x58);
 			ov5645_set_power_off(ov5645);
 		}
 	}

@@ -1049,11 +1050,20 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable)
 			dev_err(ov5645->dev, "could not sync v4l2 controls\n");
 			return ret;
 		}
+
+		ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x45);
+		if (ret < 0)
+			return ret;
+
 		ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0,
 				       OV5645_SYSTEM_CTRL0_START);
 		if (ret < 0)
 			return ret;
 	} else {
+		ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x40);
+		if (ret < 0)
+			return ret;
+
 		ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0,
 				       OV5645_SYSTEM_CTRL0_STOP);
 		if (ret < 0)

Signature · 1 line

2.20.1

Ezequiel Garcia

author

2019-07-30 08:16 UTC #1 lore raw

Hi Hans, Sakari,

Quoted 100 lines · Ezequiel Garcia

This is mostly a port of Jacopo's fix:

commit aa4bb8b8838ffcc776a79f49a4d7476b82405349
Author: Jacopo Mondi <[email protected]>
Date: Fri Jul 6 05:51:52 2018 -0400

media: ov5640: Re-work MIPI startup sequence

In the OV5645 case, the changes are:

With this commit the sensor is able to enter LP-11 mode during power up, as expected by some CSI-2 controllers.

Many thanks to Fabio Estevam for his help debugging this issue.

Tested-by Fabio Estevam <[email protected]>

Signed-off-by Ezequiel Garcia <[email protected]>

---
Changes in v2:
* As suggested by Philipp, move the initial configuration to the ov5645_global_init_setting array.

---
 drivers/media/i2c/ov5645.c | 26 ++++++++++++++++++--------
 1 file changed, 18 insertions(+), 8 deletions(-)

drivers/media/i2c/ov5645.c +14 -8

index 124c8df04633..58972c884705 100644
@@ -45,6 +45,8 @@
 #define		OV5645_CHIP_ID_HIGH_BYTE	0x56
 #define OV5645_CHIP_ID_LOW		0x300b
 #define		OV5645_CHIP_ID_LOW_BYTE		0x45
+#define OV5645_IO_MIPI_CTRL00		0x300e
+#define OV5645_PAD_OUTPUT00		0x3019
 #define OV5645_AWB_MANUAL_CONTROL	0x3406
 #define		OV5645_AWB_MANUAL_ENABLE	BIT(0)
 #define OV5645_AEC_PK_MANUAL		0x3503

@@ -55,6 +57,7 @@
 #define		OV5645_ISP_VFLIP		BIT(2)
 #define OV5645_TIMING_TC_REG21		0x3821
 #define		OV5645_SENSOR_MIRROR		BIT(1)
+#define OV5645_MIPI_CTRL00		0x4800
 #define OV5645_PRE_ISP_TEST_SETTING_1	0x503d
 #define		OV5645_TEST_PATTERN_MASK	0x3
 #define		OV5645_SET_TEST_PATTERN(x)	((x) & OV5645_TEST_PATTERN_MASK)

@@ -121,7 +124,6 @@ static const struct reg_value ov5645_global_init_setting[] = {
 	{ 0x3503, 0x07 },
 	{ 0x3002, 0x1c },
 	{ 0x3006, 0xc3 },
-	{ 0x300e, 0x45 },
 	{ 0x3017, 0x00 },
 	{ 0x3018, 0x00 },
 	{ 0x302e, 0x0b },

@@ -350,7 +352,10 @@ static const struct reg_value ov5645_global_init_setting[] = {
 	{ 0x3a1f, 0x14 },
 	{ 0x0601, 0x02 },
 	{ 0x3008, 0x42 },
-	{ 0x3008, 0x02 }
+	{ 0x3008, 0x02 },
+	{ OV5645_IO_MIPI_CTRL00, 0x40 },
+	{ OV5645_MIPI_CTRL00, 0x24 },
+	{ OV5645_PAD_OUTPUT00, 0x70 }
 };
 
 static const struct reg_value ov5645_setting_sxga[] = {

@@ -737,13 +742,9 @@ static int ov5645_s_power(struct v4l2_subdev *sd, int on)
 				goto exit;
 			}
 
-			ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0,
-					       OV5645_SYSTEM_CTRL0_STOP);
-			if (ret < 0) {
-				ov5645_set_power_off(ov5645);
-				goto exit;
-			}
+			usleep_range(500, 1000);
 		} else {
+			ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x58);
 			ov5645_set_power_off(ov5645);
 		}
 	}

@@ -1049,11 +1050,20 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable)
 			dev_err(ov5645->dev, "could not sync v4l2 controls\n");
 			return ret;
 		}
+
+		ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x45);
+		if (ret < 0)
+			return ret;
+
 		ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0,
 				       OV5645_SYSTEM_CTRL0_START);

drivers/media/i2c/ov5645.c static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable) · line 1069

Quoted 10 lines

drivers/media/i2c/ov5645.c +4 -0

 		if (ret < 0)
 			return ret;
 	} else {
+		ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x40);
+		if (ret < 0)
+			return ret;
+
 		ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0,
 				       OV5645_SYSTEM_CTRL0_STOP);
 		if (ret < 0)

Gentle reminder about this one.

Thanks!
Eze

Philipp Zabel

Reviewed-by on v2 1/1

2019-07-31 08:26 UTC #2 lore raw

In reply to Ezequiel Garcia

Quoted 20 lines · Ezequiel Garcia

This is mostly a port of Jacopo's fix:
commit aa4bb8b8838ffcc776a79f49a4d7476b82405349
Author: Jacopo Mondi <[email protected]>
Date: Fri Jul 6 05:51:52 2018 -0400
media: ov5640: Re-work MIPI startup sequence
In the OV5645 case, the changes are:
- Move OV5645_IO_MIPI_CTRL00 (0x300e) out of the initial setting blob.
- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
- At set_power(0) time power down MIPI Tx/Rx (in addition to the current power down of regulators and clock gating).
- At s_stream time enable/disable the MIPI interface output.
With this commit the sensor is able to enter LP-11 mode during power up, as expected by some CSI-2 controllers.

Quoted 8 lines

Many thanks to Fabio Estevam for his help debugging this issue.
Tested-by Fabio Estevam <[email protected]>
Signed-off-by Ezequiel Garcia <[email protected]>
---
Changes in v2:
* As suggested by Philipp, move the initial configuration to the ov5645_global_init_setting array.

Reviewed-by Philipp Zabel <[email protected]>

regards
Philipp

Jacopo Mondi

Reviewed-by on v2 1/1

2019-07-31 08:48 UTC #3 lore raw

In reply to Ezequiel Garcia

Hi Ezequiel,

Quoted 11 lines · Ezequiel Garcia

This is mostly a port of Jacopo's fix:
commit aa4bb8b8838ffcc776a79f49a4d7476b82405349
Author: Jacopo Mondi <[email protected]>
Date: Fri Jul 6 05:51:52 2018 -0400
media: ov5640: Re-work MIPI startup sequence
In the OV5645 case, the changes are:
- Move OV5645_IO_MIPI_CTRL00 (0x300e) out of the initial setting blob.

You should change this, as I still see this part of the initial settings blob.

Apart from that

Reviewed-by Jacopo Mondi <[email protected]>

Thanks
j

Quoted 102 lines

- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
- At set_power(0) time power down MIPI Tx/Rx (in addition to the current power down of regulators and clock gating).
- At s_stream time enable/disable the MIPI interface output.

With this commit the sensor is able to enter LP-11 mode during power up, as expected by some CSI-2 controllers.

Many thanks to Fabio Estevam for his help debugging this issue.

Tested-by Fabio Estevam <[email protected]>

Signed-off-by Ezequiel Garcia <[email protected]>

---
Changes in v2:
* As suggested by Philipp, move the initial configuration to the ov5645_global_init_setting array.

---
 drivers/media/i2c/ov5645.c | 26 ++++++++++++++++++--------
 1 file changed, 18 insertions(+), 8 deletions(-)

drivers/media/i2c/ov5645.c +18 -9

index 124c8df04633..58972c884705 100644
@@ -45,6 +45,8 @@
 #define		OV5645_CHIP_ID_HIGH_BYTE	0x56
 #define OV5645_CHIP_ID_LOW		0x300b
 #define		OV5645_CHIP_ID_LOW_BYTE		0x45
+#define OV5645_IO_MIPI_CTRL00		0x300e
+#define OV5645_PAD_OUTPUT00		0x3019
 #define OV5645_AWB_MANUAL_CONTROL	0x3406
 #define		OV5645_AWB_MANUAL_ENABLE	BIT(0)
 #define OV5645_AEC_PK_MANUAL		0x3503

@@ -55,6 +57,7 @@
 #define		OV5645_ISP_VFLIP		BIT(2)
 #define OV5645_TIMING_TC_REG21		0x3821
 #define		OV5645_SENSOR_MIRROR		BIT(1)
+#define OV5645_MIPI_CTRL00		0x4800
 #define OV5645_PRE_ISP_TEST_SETTING_1	0x503d
 #define		OV5645_TEST_PATTERN_MASK	0x3
 #define		OV5645_SET_TEST_PATTERN(x)	((x) & OV5645_TEST_PATTERN_MASK)

@@ -121,7 +124,6 @@ static const struct reg_value ov5645_global_init_setting[] = {
 	{ 0x3503, 0x07 },
 	{ 0x3002, 0x1c },
 	{ 0x3006, 0xc3 },
-	{ 0x300e, 0x45 },
 	{ 0x3017, 0x00 },
 	{ 0x3018, 0x00 },
 	{ 0x302e, 0x0b },

@@ -350,7 +352,10 @@ static const struct reg_value ov5645_global_init_setting[] = {
 	{ 0x3a1f, 0x14 },
 	{ 0x0601, 0x02 },
 	{ 0x3008, 0x42 },
-	{ 0x3008, 0x02 }
+	{ 0x3008, 0x02 },
+	{ OV5645_IO_MIPI_CTRL00, 0x40 },
+	{ OV5645_MIPI_CTRL00, 0x24 },
+	{ OV5645_PAD_OUTPUT00, 0x70 }
 };
 
 static const struct reg_value ov5645_setting_sxga[] = {

@@ -737,13 +742,9 @@ static int ov5645_s_power(struct v4l2_subdev *sd, int on)
 				goto exit;
 			}
 
-			ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0,
-					       OV5645_SYSTEM_CTRL0_STOP);
-			if (ret < 0) {
-				ov5645_set_power_off(ov5645);
-				goto exit;
-			}
+			usleep_range(500, 1000);
 		} else {
+			ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x58);
 			ov5645_set_power_off(ov5645);
 		}
 	}

@@ -1049,11 +1050,20 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable)
 			dev_err(ov5645->dev, "could not sync v4l2 controls\n");
 			return ret;
 		}
+
+		ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x45);
+		if (ret < 0)
+			return ret;
+
 		ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0,
 				       OV5645_SYSTEM_CTRL0_START);
 		if (ret < 0)
 			return ret;
 	} else {
+		ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x40);
+		if (ret < 0)
+			return ret;
+
 		ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0,
 				       OV5645_SYSTEM_CTRL0_STOP);
 		if (ret < 0)
--

2.20.1