Skip to contentSkip to conversation

staging: dt-bindings: wilc1000: add optional rtc_clk property

PATCH New [email protected] 1 participant 2 messages Sep 9, 2019 Staging

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/2 staging: dt-bindings: wilc1000: add optional rtc_clk property

From: Eugen Hristev <[email protected]>

Add bindings for optional rtc clock pin.

---

Changes in v2:
- none

 drivers/staging/wilc1000/microchip,wilc1000,sdio.txt | 8 +++++++-
 drivers/staging/wilc1000/microchip,wilc1000,spi.txt  | 8 ++++++++
 2 files changed, 15 insertions(+), 1 deletion(-)
drivers/staging/wilc1000/microchip,wilc1000,sdio.txt +7 -1
index 4f7d1c2..da52359 100644
@@ -10,7 +10,9 @@ Required properties:
 
 Optional:
 - bus-width	:	Number of data lines wired up the slot. Default 1 bit.
-
+- rtc_clk	:	Clock connected on the rtc clock line. Must be assigned
+			a frequency with assigned-clocks property, and must be
+			connected to a clock provider.
 
 Examples:
 mmc1: mmc@fc000000 {
@@ -24,6 +26,10 @@ mmc1: mmc@fc000000 {
 		wilc_sdio@0 {
 			compatible = "microchip,wilc1000-sdio";
 			irq-gpios = <&pioC 27 0>;
+			clocks = <&pck1>;
+			clock-names = "rtc_clk";
+			assigned-clocks = <&pck1>;
+			assigned-clock-rates = <32768>;
 			status = "okay";
 			reg = <0>;
 			bus-width = <4>;
drivers/staging/wilc1000/microchip,wilc1000,spi.txt +8 -0
index 87db87b..3423693 100644
@@ -9,6 +9,10 @@ Required properties:
 - reg			: Chip select address of device
 - irq-gpios		: Connect to a host IRQ
 
+Optional:
+- rtc_clk	:	Clock connected on the rtc clock line. Must be assigned
+			a frequency with assigned-clocks property, and must be
+			connected to a clock provider.
 
 Examples:
 
@@ -21,6 +25,10 @@ spi1: spi@fc018000 {
 			spi-max-frequency = <48000000>;
 			reg = <0>;
 			irq-gpios = <&pioC 27 0>;
+			clocks = <&pck1>;
+			clock-names = "rtc_clk";
+			assigned-clocks = <&pck1>;
+			assigned-clock-rates = <32768>;
 			status = "okay";
 		};
 };
Signature · 1 line
2.7.4
#1 lore raw

PATCH v2 2/2 staging: wilc1000: look for rtc_clk clock

From: Eugen Hristev <[email protected]>

If rtc_clk is provided from DT, use it and enable it. This is optional.
The signal may be hardcoded and no need to be requested, but if DT provides it, use it.

---

Changes in v2:
- rebased on staging-next

 drivers/staging/wilc1000/wilc_sdio.c          | 14 ++++++++++++++
 drivers/staging/wilc1000/wilc_wfi_netdevice.h |  1 +
 2 files changed, 15 insertions(+)
drivers/staging/wilc1000/wilc_sdio.c +14 -0
index 2f9aa36..c787c5d 100644
@@ -4,6 +4,7 @@
  * All rights reserved.
  */
 
+#include <linux/clk.h>
 #include <linux/mmc/sdio_func.h>
 #include <linux/mmc/host.h>
 
@@ -151,6 +152,12 @@ static int wilc_sdio_probe(struct sdio_func *func,
 	wilc->dev = &func->dev;
 	wilc->gpio_irq = gpio;
 
+	wilc->rtc_clk = devm_clk_get(&func->card->dev, "rtc_clk");
+	if (PTR_ERR_OR_ZERO(wilc->rtc_clk) == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+	else if (!IS_ERR(wilc->rtc_clk))
+		clk_prepare_enable(wilc->rtc_clk);
+
 	dev_info(&func->dev, "Driver Initializing success\n");
 	return 0;
 }
@@ -162,6 +169,10 @@ static void wilc_sdio_remove(struct sdio_func *func)
 	/* free the GPIO in module remove */
 	if (wilc->gpio_irq)
 		gpiod_put(wilc->gpio_irq);
+
+	if (!IS_ERR(wilc->rtc_clk))
+		clk_disable_unprepare(wilc->rtc_clk);
+
 	wilc_netdev_cleanup(wilc);
 }
 
@@ -193,6 +204,9 @@ static int wilc_sdio_suspend(struct device *dev)
 	dev_info(dev, "sdio suspend\n");
 	chip_wakeup(wilc);
 
+	if (!IS_ERR(wilc->rtc_clk))
+		clk_disable_unprepare(wilc->rtc_clk);
+
 	if (wilc->suspend_event) {
 		host_sleep_notify(wilc);
 		chip_allow_sleep(wilc);
drivers/staging/wilc1000/wilc_wfi_netdevice.h +1 -0
index 7e7ce94..978a8bd 100644
@@ -216,6 +216,7 @@ struct wilc {
 	int io_type;
 	s8 mac_status;
 	struct gpio_desc *gpio_irq;
+	struct clk *rtc_clk;
 	bool initialized;
 	int dev_irq_num;
 	int close;
Signature · 1 line
2.7.4