Skip to contentSkip to conversation

Add framebuffer max width/height fields to drm_mode_config

PATCH New Jeykumar Sankaran 2 participants 3 messages Sep 28, 2019 – Sep 29, 2019

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Add framebuffer max width/height fields to drm_mode_config

Below two discussion threads will provide the context behind this patch.

https://www.spinics.net/lists/dri-devel/msg229070.html
https://lore.kernel.org/linux-arm-msm/[email protected]/T/

Seperating out the core framework patch from vendor implementation.

Jeykumar Sankaran (1):
drm: add fb max width/height fields to drm_mode_config

 drivers/gpu/drm/drm_framebuffer.c | 17 +++++++++++++----
 include/drm/drm_mode_config.h     |  3 +++
 2 files changed, 16 insertions(+), 4 deletions(-)
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
#1 lore raw

PATCH 1/1 drm: add fb max width/height fields to drm_mode_config

The mode_config max width/height values determine the maximum resolution the pixel reader can handle. But the same values are used to restrict the size of the framebuffer creation. Hardware's with scaling blocks can operate on framebuffers larger/smaller than that of the pixel reader resolutions by scaling them down/up before rendering.

This changes adds a separate framebuffer max width/height fields in drm_mode_config to allow vendors to set if they are different than that of the default max resolution values.

Vendors setting these fields should fix their mode_set paths too by filtering and validating the modes against the appropriate max fields in their mode_valid() implementations.

---
 drivers/gpu/drm/drm_framebuffer.c | 15 +++++++++++----
 include/drm/drm_mode_config.h     |  3 +++
 2 files changed, 14 insertions(+), 4 deletions(-)
drivers/gpu/drm/drm_framebuffer.c +11 -4
index 5756431..2083168 100644
@@ -300,14 +300,21 @@ struct drm_framebuffer *
 		return ERR_PTR(-EINVAL);
 	}
 
-	if ((config->min_width > r->width) || (r->width > config->max_width)) {
+	if ((config->min_width > r->width) ||
+	    (!config->max_fb_width && r->width > config->max_width) ||
+	    (config->max_fb_width && r->width > config->max_fb_width)) {
 		DRM_DEBUG_KMS("bad framebuffer width %d, should be >= %d && <= %d\n",
-			  r->width, config->min_width, config->max_width);
+			r->width, config->min_width, config->max_fb_width ?
+			config->max_fb_width : config->max_width);
 		return ERR_PTR(-EINVAL);
 	}
-	if ((config->min_height > r->height) || (r->height > config->max_height)) {
+
+	if ((config->min_height > r->height) ||
+	    (!config->max_fb_height && r->height > config->max_height) ||
+	    (config->max_fb_height && r->height > config->max_fb_height)) {
 		DRM_DEBUG_KMS("bad framebuffer height %d, should be >= %d && <= %d\n",
-			  r->height, config->min_height, config->max_height);
+			r->height, config->min_height, config->max_fb_width ?
+			config->max_fb_height : config->max_height);
 		return ERR_PTR(-EINVAL);
 	}
 
include/drm/drm_mode_config.h +3 -0
index 3bcbe30..c6394ed 100644
@@ -339,6 +339,8 @@ struct drm_mode_config_funcs {
  * @min_height: minimum fb pixel height on this device
  * @max_width: maximum fb pixel width on this device
  * @max_height: maximum fb pixel height on this device
+ * @max_fb_width: maximum fb buffer width if differs from max_width
+ * @max_fb_height: maximum fb buffer height if differs from  max_height
  * @funcs: core driver provided mode setting functions
  * @fb_base: base address of the framebuffer
  * @poll_enabled: track polling support for this device
@@ -523,6 +525,7 @@ struct drm_mode_config {
 
 	int min_width, min_height;
 	int max_width, max_height;
+	int max_fb_width, max_fb_height;
 	const struct drm_mode_config_funcs *funcs;
 	resource_size_t fb_base;
 
Signature · 7 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#2 lore raw

Re: drm: add fb max width/height fields to drm_mode_config

Quoted 11 lines · Jeykumar Sankaran

The mode_config max width/height values determine the maximum resolution the pixel reader can handle. But the same values are used to restrict the size of the framebuffer creation. Hardware's with scaling blocks can operate on framebuffers larger/smaller than that of the pixel reader resolutions by scaling them down/up before rendering.

This changes adds a separate framebuffer max width/height fields in drm_mode_config to allow vendors to set if they are different than that of the default max resolution values.

Quoted 6 lines

Vendors setting these fields should fix their mode_set paths too by filtering and validating the modes against the appropriate max fields in their mode_valid() implementations.

Hi Jeykumar:

Komeda driver also meets this problem, thank for the fix.

Thanks
James

Quoted 49 lines
---
 drivers/gpu/drm/drm_framebuffer.c | 15 +++++++++++----
 include/drm/drm_mode_config.h     |  3 +++
 2 files changed, 14 insertions(+), 4 deletions(-)
drivers/gpu/drm/drm_framebuffer.c +11 -4
index 5756431..2083168 100644
@@ -300,14 +300,21 @@ struct drm_framebuffer *
 		return ERR_PTR(-EINVAL);
 	}
 
-	if ((config->min_width > r->width) || (r->width > config->max_width)) {
+	if ((config->min_width > r->width) ||
+	    (!config->max_fb_width && r->width > config->max_width) ||
+	    (config->max_fb_width && r->width > config->max_fb_width)) {
 		DRM_DEBUG_KMS("bad framebuffer width %d, should be >= %d && <= %d\n",
-			  r->width, config->min_width, config->max_width);
+			r->width, config->min_width, config->max_fb_width ?
+			config->max_fb_width : config->max_width);
 		return ERR_PTR(-EINVAL);
 	}
-	if ((config->min_height > r->height) || (r->height > config->max_height)) {
+
+	if ((config->min_height > r->height) ||
+	    (!config->max_fb_height && r->height > config->max_height) ||
+	    (config->max_fb_height && r->height > config->max_fb_height)) {
 		DRM_DEBUG_KMS("bad framebuffer height %d, should be >= %d && <= %d\n",
-			  r->height, config->min_height, config->max_height);
+			r->height, config->min_height, config->max_fb_width ?
+			config->max_fb_height : config->max_height);
 		return ERR_PTR(-EINVAL);
 	}
 
include/drm/drm_mode_config.h +2 -0
index 3bcbe30..c6394ed 100644
@@ -339,6 +339,8 @@ struct drm_mode_config_funcs {
  * @min_height: minimum fb pixel height on this device
  * @max_width: maximum fb pixel width on this device
  * @max_height: maximum fb pixel height on this device
+ * @max_fb_width: maximum fb buffer width if differs from max_width
+ * @max_fb_height: maximum fb buffer height if differs from  max_height
  * @funcs: core driver provided mode setting functions
  * @fb_base: base address of the framebuffer
  * @poll_enabled: track polling support for this device

include/drm/drm_mode_config.h struct drm_mode_config { · line 531

Quoted 7 lines
include/drm/drm_mode_config.h +1 -0
@@ -523,6 +525,7 @@ struct drm_mode_config {
 
 	int min_width, min_height;
 	int max_width, max_height;
+	int max_fb_width, max_fb_height;
 	const struct drm_mode_config_funcs *funcs;
 	resource_size_t fb_base;
 

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel