clk: at91: sam9x60-pll: adapt PMC_PLL_ACR default value
Subsystems (2)
PATCH 1/1 clk: at91: sam9x60-pll: adapt PMC_PLL_ACR default value
From: Eugen Hristev <[email protected]>
Product datasheet recommends different values for UPLL and PLLA analog control register.
Adapt accordingly.
---
datasheet link http://ww1.microchip.com/downloads/en/DeviceDoc/SAM9X60-Data-Sheet-DS60001579A.pdf
chapter 57.7.10 optimal setting of the PLLA and PLLUTMI
drivers/clk/at91/clk-sam9x60-pll.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-)
drivers/clk/at91/clk-sam9x60-pll.c +6 -2
@@ -25,7 +25,8 @@#define PMC_PLL_CTRL1_MUL_MSK GENMASK(30, 24)#define PMC_PLL_ACR 0x18 -#define PMC_PLL_ACR_DEFAULT 0x1b040010UL +#define PMC_PLL_ACR_DEFAULT_UPLL 0x12020010UL +#define PMC_PLL_ACR_DEFAULT_PLLA 0x00020010UL#define PMC_PLL_ACR_UTMIVR BIT(12)#define PMC_PLL_ACR_UTMIBG BIT(13)#define PMC_PLL_ACR_LOOP_FILTER_MSK GENMASK(31, 24)
@@ -88,7 +89,10 @@ static int sam9x60_pll_prepare(struct clk_hw *hw) }/* Recommended value for PMC_PLL_ACR */ - val =PMC_PLL_ACR_DEFAULT ; +if (pll->characteristics->upll) + val =PMC_PLL_ACR_DEFAULT_UPLL ; +else + val =PMC_PLL_ACR_DEFAULT_PLLA ;regmap_write (regmap,PMC_PLL_ACR , val); regmap_write(regmap, PMC_PLL_CTRL1,
Signature · 1 line
2.7.4
Quoted 7 lines · On 11/11/2019 at 14:28, Eugen Hristev - M18282 wrote:
From: Eugen Hristev <[email protected]>
Product datasheet recommends different values for UPLL and PLLA analog control register.
Adapt accordingly.Signed-off-by Eugen Hristev <[email protected]>
Best regards,
Nicolas
Quoted 35 lines
---
datasheet link http://ww1.microchip.com/downloads/en/DeviceDoc/SAM9X60-Data-Sheet-DS60001579A.pdf
chapter 57.7.10 optimal setting of the PLLA and PLLUTMIdrivers/clk/at91/clk-sam9x60-pll.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-)drivers/clk/at91/clk-sam9x60-pll.c +6
-2@@ -25,7 +25,8 @@#define PMC_PLL_CTRL1_MUL_MSK GENMASK(30, 24)#define PMC_PLL_ACR 0x18 -#define PMC_PLL_ACR_DEFAULT 0x1b040010UL +#define PMC_PLL_ACR_DEFAULT_UPLL 0x12020010UL +#define PMC_PLL_ACR_DEFAULT_PLLA 0x00020010UL#define PMC_PLL_ACR_UTMIVR BIT(12)#define PMC_PLL_ACR_UTMIBG BIT(13)#define PMC_PLL_ACR_LOOP_FILTER_MSK GENMASK(31, 24)@@ -88,7 +89,10 @@ static int sam9x60_pll_prepare(struct clk_hw *hw) }/* Recommended value for PMC_PLL_ACR */ - val =PMC_PLL_ACR_DEFAULT ; +if (pll->characteristics->upll) + val =PMC_PLL_ACR_DEFAULT_UPLL ; +else + val =PMC_PLL_ACR_DEFAULT_PLLA ;regmap_write (regmap,PMC_PLL_ACR , val); regmap_write(regmap, PMC_PLL_CTRL1,
Signature · 6 lines
Nicolas Ferre _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoting [email protected] (2019-11-11 05:28:57)
Quoted 8 lines
From: Eugen Hristev <[email protected]>
Product datasheet recommends different values for UPLL and PLLA analog control register.
Adapt accordingly.Signed-off-by Eugen Hristev <[email protected]>---
Applied to clk-next