Skip to contentSkip to conversation

arm: imx6: cm_fx6: Enable DM SPI and SPI_FLASH, fix SPL build errors

PATCH RESEND New sunil.m at techveda.org 2 participants 2 messages Nov 27, 2019 – Dec 29, 2019

lore
Share & tools
lore
#0 lore raw

PATCH RESEND 1/1 arm: imx6: cm_fx6: Enable DM SPI and SPI_FLASH, fix SPL build errors

From: Suniel Mahesh <[email protected]>

Enable driver model for SPI and SPI_FLASH to remove the following compile warning on CM-FX6 SOM:
===================== WARNING ====================== This board does not use CONFIG_DM_SPI_FLASH. Please update the board to use CONFIG_SPI_FLASH before the v2019.07 release.
====================================================

This change introduced SPL build error as shown:

In file included from include/common.h:47:0,

                 from drivers/mtd/spi/sf_probe.c:10:

drivers/mtd/spi/sf_probe.c: In function 'spi_flash_std_probe':
drivers/mtd/spi/sf_probe.c:149:54: error: dereferencing pointer to incomplete type 'struct dm_spi_slave_platdata' scripts/Makefile.build:278: recipe for target 'spl/drivers/mtd/spi/sf_probe.o' failed
make[3]: *** [spl/drivers/mtd/spi/sf_probe.o] Error 1
scripts/Makefile.build:432: recipe for target 'spl/drivers/mtd/spi' failed
make[2]: *** [spl/drivers/mtd/spi] Error 2

Disabling DM for SPI support(SPI and SF) in SPL resolves the issue. Target was compile tested, build was clean.

---
 configs/cm_fx6_defconfig | 2 ++
 include/configs/cm_fx6.h | 7 +++++++
 2 files changed, 9 insertions(+)
configs/cm_fx6_defconfig +2 -0
index 218d3d6..ca9895e 100644
@@ -66,6 +66,7 @@ CONFIG_FSL_USDHC=y
 CONFIG_NAND=y
 CONFIG_NAND_MXS=y
 CONFIG_SPI_FLASH=y
+CONFIG_DM_SPI_FLASH=y
 CONFIG_SF_DEFAULT_MODE=0
 CONFIG_SF_DEFAULT_SPEED=25000000
 CONFIG_SPI_FLASH_ATMEL=y
@@ -82,6 +83,7 @@ CONFIG_MII=y
 CONFIG_DM_PMIC=y
 CONFIG_DM_REGULATOR=y
 CONFIG_SPI=y
+CONFIG_DM_SPI=y
 CONFIG_MXC_SPI=y
 CONFIG_USB=y
 CONFIG_DM_USB=y
include/configs/cm_fx6.h +7 -0
index eb29f07..53ae5f0 100644
@@ -153,6 +153,13 @@
 /* APBH DMA is required for NAND support */
 #endif
 
+/* SPI Flash Configs */
+#if defined(CONFIG_SPL_BUILD)
+#undef CONFIG_DM_SPI
+#undef CONFIG_DM_SPI_FLASH
+#undef CONFIG_SPI_FLASH_MTD
+#endif
+
 /* Ethernet */
 #define CONFIG_FEC_MXC
 #define CONFIG_FEC_MXC_PHYADDR		0
Signature · 1 line
2.7.4
#1 lore raw

PATCH RESEND 1/1 arm: imx6: cm_fx6: Enable DM SPI and SPI_FLASH, fix SPL build errors

Quoted 18 lines

From: Suniel Mahesh <[email protected]>
Enable driver model for SPI and SPI_FLASH to remove the following compile warning on CM-FX6 SOM:
===================== WARNING ====================== This board does not use CONFIG_DM_SPI_FLASH. Please update the board to use CONFIG_SPI_FLASH before the v2019.07 release.
====================================================
This change introduced SPL build error as shown:
In file included from include/common.h:47:0,

                 from drivers/mtd/spi/sf_probe.c:10:

drivers/mtd/spi/sf_probe.c: In function 'spi_flash_std_probe':
drivers/mtd/spi/sf_probe.c:149:54: error: dereferencing pointer to incomplete type 'struct dm_spi_slave_platdata' scripts/Makefile.build:278: recipe for target 'spl/drivers/mtd/spi/sf_probe.o' failed
make[3]: *** [spl/drivers/mtd/spi/sf_probe.o] Error 1
scripts/Makefile.build:432: recipe for target 'spl/drivers/mtd/spi' failed
make[2]: *** [spl/drivers/mtd/spi] Error 2
Disabling DM for SPI support(SPI and SF) in SPL resolves the issue.
Target was compile tested, build was clean.

Quoted 1 line

Applied to u-boot-imx, -next, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================