UFS driver general fixes bundle 4
Subsystems (3)
v9 cover UFS driver general fixes bundle 4
This bundle includes 7 general fixes for UFS driver.
Changes since v8:
- Incoperated comments from Arvi to add "Fixes" to commit message of patch #4
- Switched the order of patch #2 and #3 to reflect the dependency.
Changes since v7:
- Incoperated comments from Bjorn and Arvi.
- Removed patch #8.
Changes since v6:
- Incoperated Avri's comment.
Changes since v5:
- Incoperated Stanley's suggestions to make the extra delay added up to bRefClkGatingWaitTime as vendor specific
Changes since v4:
- Rebased this series
Changes since v3:
- Fixed patch #8
Changes since v2:
- Move the ref clk gating wait delay to ufs-qcom.c
- Added one more change to select INITIAL adapt for HS G4
Changes since v1:
- Fixed minor typo
Asutosh Das (1):
scsi: ufs: set load before setting voltage in regulators
Can Guo (5):
scsi: ufs-qcom: Adjust bus bandwidth voting and unvoting
scsi: ufs: Remove the check before call setup clock notify vops
scsi: ufs: Fix ufshcd_hold() caused scheduling while atomic
scsi: ufs: Add dev ref clock gating wait time support
scsi: ufs-qcom: Delay specific time before gate ref clk
Sayali Lokhande (1):
scsi: ufs: Flush exception event before suspend
drivers/scsi/ufs/ufs-qcom.c | 100 +++++++++++++++++++++++++++++++------------- drivers/scsi/ufs/ufs.h | 3 ++ drivers/scsi/ufs/ufshcd.c | 96 +++++++++++++++++++++++++++++------------- 3 files changed, 143 insertions(+), 56 deletions(-)
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
PATCH v9 1/7 scsi: ufs: Flush exception event before suspend
From: Sayali Lokhande <[email protected]>
Exception event can be raised by the device when system suspend is in progress. This will result in unclocked register access in exception event handler as clocks will be turned off during suspend. This change makes sure to flush exception event handler work in suspend before disabling clocks to avoid unclocked register access issue.
--- drivers/scsi/ufs/ufshcd.c | 21 ++++++++++++++++++--- 1 file changed, 18 insertions(+), 3 deletions(-)
drivers/scsi/ufs/ufshcd.c +18 -3
@@ -4730,8 +4730,15 @@ static void ufshcd_slave_destroy(struct scsi_device *sdev)* UFS device needs urgent BKOPs. */ if (!hba->pm_op_in_progress && -ufshcd_is_exception_event (lrbp->ucd_rsp_ptr)) -schedule_work (&hba->eeh_work); +ufshcd_is_exception_event (lrbp->ucd_rsp_ptr) && +schedule_work (&hba->eeh_work)) { +/* +* Prevent suspend once eeh_work is scheduled +* to avoid deadlock between ufshcd_suspend +* and exception event handler. +*/ +pm_runtime_get_noresume (hba->dev); + }break ;case UPIU_TRANSACTION_REJECT_UPIU :/* TODO: handle Reject UPIU Response */
@@ -5184,7 +5191,14 @@ static void ufshcd_exception_event_handler(struct work_struct *work) out:ufshcd_scsi_unblock_requests (hba); -pm_runtime_put_sync (hba->dev); +/* +* pm_runtime_get_noresume is called while scheduling +* eeh_work to avoid suspend racing with exception work. +* Hence decrement usage counter using pm_runtime_put_noidle +* to allow suspend on completion of exception event handler. +*/ +pm_runtime_put_noidle (hba->dev); +pm_runtime_put (hba->dev);return ; }
@@ -7924,6 +7938,7 @@ static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op) goto enable_gating; } +flush_work (&hba->eeh_work); ret =ufshcd_link_state_transition (hba, req_link_state,1 );if (ret) goto set_dev_active;
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
PATCH v9 2/7 scsi: ufs: set load before setting voltage in regulators
In reply to Can GuoFrom: Asutosh Das <[email protected]>
This sequence change is required to avoid dips in voltage during boot-up.
Apparently, this dip is caused because in the original sequence, the regulators are initialized in lpm mode. And then when the load is set to high, and more current is drawn, than is allowed in lpm, the dip is seen.
--- drivers/scsi/ufs/ufshcd.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-)
drivers/scsi/ufs/ufshcd.c +5 -5
@@ -7248,6 +7248,11 @@ static int ufshcd_config_vreg(struct device *dev, name = vreg->name;if (regulator_count_voltages (reg) >0 ) { + uA_load = on ? vreg->max_uA :0 ; + ret =ufshcd_config_vreg_load (dev, vreg, uA_load); +if (ret) + goto out; +if (vreg->min_uV && vreg->max_uV) { min_uV = on ? vreg->min_uV :0 ; ret =regulator_set_voltage (reg, min_uV, vreg->max_uV);
@@ -7258,11 +7263,6 @@ static int ufshcd_config_vreg(struct device *dev, goto out; } } - - uA_load = on ? vreg->max_uA :0 ; - ret =ufshcd_config_vreg_load (dev, vreg, uA_load); -if (ret) - goto out; } out:return ret;
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
PATCH v9 3/7 scsi: ufs-qcom: Adjust bus bandwidth voting and unvoting
In reply to Can GuoThe bus bandwidth voting is required to be done before the bus clocks are enabled, and the unvoting is required to be done only after the bus clocks are disabled.
--- drivers/scsi/ufs/ufs-qcom.c | 78 ++++++++++++++++++++++++++++++--------------- 1 file changed, 53 insertions(+), 25 deletions(-)
drivers/scsi/ufs/ufs-qcom.c +53 -25
@@ -38,7 +38,6 @@ enum {static struct ufs_qcom_host *ufs_qcom_hosts[MAX_UFS_QCOM_HOSTS ]; -static int ufs_qcom_set_bus_vote (struct ufs_qcom_host *host,int vote);static void ufs_qcom_get_default_testbus_cfg (struct ufs_qcom_host *host);static int ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div (struct ufs_hba *hba,u32 clk_cycles);
@@ -674,7 +673,7 @@ static void ufs_qcom_get_speed_mode(struct ufs_pa_layer_attr *p, char *result) } } -static int ufs_qcom_set_bus_vote (struct ufs_qcom_host *host,int vote) +static int __ufs_qcom_set_bus_vote (struct ufs_qcom_host *host,int vote) {int err =0 ;
@@ -705,7 +704,7 @@ static int ufs_qcom_update_bus_bw_vote(struct ufs_qcom_host *host) vote =ufs_qcom_get_bus_vote (host, mode);if (vote >=0 ) - err =ufs_qcom_set_bus_vote (host, vote); + err =__ufs_qcom_set_bus_vote (host, vote);else err = vote;
@@ -716,6 +715,35 @@ static int ufs_qcom_update_bus_bw_vote(struct ufs_qcom_host *host)return err; } +static int ufs_qcom_set_bus_vote (struct ufs_hba *hba,bool on) +{ +struct ufs_qcom_host *host =ufshcd_get_variant (hba); +int vote, err; + +/* +* In case ufs_qcom_init() is not yet done, simply ignore. +* This ufs_qcom_set_bus_vote() shall be called from +* ufs_qcom_init() after init is done. +*/ +if (!host) +return 0 ; + +if (on) { + vote = host->bus_vote.saved_vote; +if (vote == host->bus_vote.min_bw_vote) +ufs_qcom_update_bus_bw_vote (host); + }else { + vote = host->bus_vote.min_bw_vote; + } + + err =__ufs_qcom_set_bus_vote (host, vote); +if (err) +dev_err (hba->dev,"%s: set bus vote failed %d\n" , + __func__, err); + +return err; +} +static ssize_t show_ufs_to_mem_max_bus_bw (struct device *dev,struct device_attribute *attr,char *buf)
@@ -792,7 +820,7 @@ static int ufs_qcom_update_bus_bw_vote(struct ufs_qcom_host *host)return 0 ; } -static int ufs_qcom_set_bus_vote (struct ufs_qcom_host *host,int vote) +static int ufs_qcom_set_bus_vote (struct ufs_hba *host,bool on) {return 0 ; }
@@ -1030,8 +1058,7 @@ static int ufs_qcom_setup_clocks(struct ufs_hba *hba, bool on, enum ufs_notify_change_status status) {struct ufs_qcom_host *host =ufshcd_get_variant (hba); -int err; -int vote =0 ; +int err =0 ;/* * In case ufs_qcom_init() is not yet done, simply ignore.
@@ -1041,28 +1068,28 @@ static int ufs_qcom_setup_clocks(struct ufs_hba *hba, bool on,if (!host)return 0 ; -if (on && (status ==POST_CHANGE )) { -/* enable the device ref clock for HS mode*/ -if (ufshcd_is_hs_mode (&hba->pwr_info)) -ufs_qcom_dev_ref_clk_ctrl (host, true); - vote = host->bus_vote.saved_vote; -if (vote == host->bus_vote.min_bw_vote) -ufs_qcom_update_bus_bw_vote (host); - - }else if (!on && (status ==PRE_CHANGE )) { -if (!ufs_qcom_is_link_active (hba)) { -/* disable device ref_clk */ -ufs_qcom_dev_ref_clk_ctrl (host, false); +switch (status) { +case PRE_CHANGE : +if (on) { + err =ufs_qcom_set_bus_vote (hba, true); + }else { +if (!ufs_qcom_is_link_active (hba)) { +/* disable device ref_clk */ +ufs_qcom_dev_ref_clk_ctrl (host, false); + } } - - vote = host->bus_vote.min_bw_vote; +break ; +case POST_CHANGE : +if (on) { +/* enable the device ref clock for HS mode*/ +if (ufshcd_is_hs_mode (&hba->pwr_info)) +ufs_qcom_dev_ref_clk_ctrl (host, true); + }else { + err =ufs_qcom_set_bus_vote (hba, false); + } +break ; } - err =ufs_qcom_set_bus_vote (host, vote); -if (err) -dev_err (hba->dev,"%s: set bus vote failed %d\n" , - __func__, err); -return err; }
@@ -1238,6 +1265,7 @@ static int ufs_qcom_init(struct ufs_hba *hba)ufs_qcom_set_caps (hba);ufs_qcom_advertise_quirks (hba); +ufs_qcom_set_bus_vote (hba, true);ufs_qcom_setup_clocks (hba, true,POST_CHANGE );if (hba->dev->id <MAX_UFS_QCOM_HOSTS )
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
Re: [PATCH v9 3/7] scsi: ufs-qcom: Adjust bus bandwidth voting and unvoting
Hi Can,
Quoted 156 lines · Can Guo
The bus bandwidth voting is required to be done before the bus clocks are enabled, and the unvoting is required to be done only after the bus clocks are disabled.
Signed-off-by Can Guo <[email protected]>Reviewed-by Asutosh Das <[email protected]>--- drivers/scsi/ufs/ufs-qcom.c | 78 ++++++++++++++++++++++++++++++--------------- 1 file changed, 53 insertions(+), 25 deletions(-)drivers/scsi/ufs/ufs-qcom.c +0
-1@@ -38,7 +38,6 @@ enum {static struct ufs_qcom_host *ufs_qcom_hosts[MAX_UFS_QCOM_HOSTS ]; -static int ufs_qcom_set_bus_vote (struct ufs_qcom_host *host,int vote);static void ufs_qcom_get_default_testbus_cfg (struct ufs_qcom_host *host);static int ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div(struct
ufs_hba
*hba,drivers/scsi/ufs/ufs-qcom.c +1
-1u32 clk_cycles);@@ -674,7 +673,7 @@ static void ufs_qcom_get_speed_mode(struct ufs_pa_layer_attr *p, char *result) } } -static int ufs_qcom_set_bus_vote (struct ufs_qcom_host *host,int vote) +static int __ufs_qcom_set_bus_vote (struct ufs_qcom_host *host,int vote) {drivers/scsi/ufs/ufs-qcom.c +30
-1int err =0 ;@@ -705,7 +704,7 @@ static int ufs_qcom_update_bus_bw_vote(struct ufs_qcom_host *host) vote =ufs_qcom_get_bus_vote (host, mode);if (vote >=0 ) - err =ufs_qcom_set_bus_vote (host, vote); + err =__ufs_qcom_set_bus_vote (host, vote);else err = vote;@@ -716,6 +715,35 @@ static int ufs_qcom_update_bus_bw_vote(struct ufs_qcom_host *host)return err; } +static int ufs_qcom_set_bus_vote (struct ufs_hba *hba,bool on) +{ +struct ufs_qcom_host *host =ufshcd_get_variant (hba); +int vote, err; + +/* +* In case ufs_qcom_init() is not yet done, simply ignore. +* This ufs_qcom_set_bus_vote() shall be called from +* ufs_qcom_init() after init is done. +*/ +if (!host) +return 0 ; + +if (on) { + vote = host->bus_vote.saved_vote; +if (vote == host->bus_vote.min_bw_vote) +ufs_qcom_update_bus_bw_vote (host); + }else { + vote = host->bus_vote.min_bw_vote; + } + + err =__ufs_qcom_set_bus_vote (host, vote); +if (err) +dev_err (hba->dev,"%s: set bus vote failed %d\n" , + __func__, err); + +return err; +} +static ssize_t show_ufs_to_mem_max_bus_bw(struct device *dev, struct device_attribute*attr,
drivers/scsi/ufs/ufs-qcom.c +1
-1char *buf)@@ -792,7 +820,7 @@ static int ufs_qcom_update_bus_bw_vote(struct ufs_qcom_host *host)return 0 ; } -static int ufs_qcom_set_bus_vote (struct ufs_qcom_host *host,int vote) +static int ufs_qcom_set_bus_vote (struct ufs_hba *host,bool on) {return 0 ;}
drivers/scsi/ufs/ufs-qcom.c +1
-2@@ -1030,8 +1058,7 @@ static int ufs_qcom_setup_clocks(struct ufs_hba *hba, bool on, enum ufs_notify_change_status status) {struct ufs_qcom_host *host =ufshcd_get_variant (hba); -int err; -int vote =0 ; +int err =0 ;/* drivers/scsi/ufs/ufs-qcom.c +19
-19* In case ufs_qcom_init() is not yet done, simply ignore. @@ -1041,28 +1068,28 @@ static int ufs_qcom_setup_clocks(struct ufs_hba *hba, bool on, if (!host) return 0; - if (on && (status == POST_CHANGE)) { - /* enable the device ref clock for HS mode*/ - if (ufshcd_is_hs_mode(&hba->pwr_info)) - ufs_qcom_dev_ref_clk_ctrl(host, true); - vote = host->bus_vote.saved_vote; -if (vote == host->bus_vote.min_bw_vote) -ufs_qcom_update_bus_bw_vote (host); - - }else if (!on && (status ==PRE_CHANGE )) { -if (!ufs_qcom_is_link_active (hba)) { -/* disable device ref_clk */ -ufs_qcom_dev_ref_clk_ctrl (host, false); +switch (status) { +case PRE_CHANGE : +if (on) { + err =ufs_qcom_set_bus_vote (hba, true); + }else { +if (!ufs_qcom_is_link_active (hba)) { +/* disable device ref_clk */ +ufs_qcom_dev_ref_clk_ctrl (host, false); + } } - - vote = host->bus_vote.min_bw_vote; +break ; +case POST_CHANGE : +if (on) { +/* enable the device ref clock for HS mode*/ +if (ufshcd_is_hs_mode (&hba->pwr_info)) +ufs_qcom_dev_ref_clk_ctrl (host, true); + }else { + err =ufs_qcom_set_bus_vote (hba, false); + } +break ; } - err =ufs_qcom_set_bus_vote (host, vote); -if (err) -dev_err (hba->dev,"%s: set bus vote failed %d\n" , - __func__, err); -return err; }
drivers/scsi/ufs/ufs-qcom.c static int ufs_qcom_init(struct ufs_hba *hba) · line 1271
Quoted 7 lines
drivers/scsi/ufs/ufs-qcom.c +1
-0@@ -1238,6 +1265,7 @@ static int ufs_qcom_init(struct ufs_hba *hba)ufs_qcom_set_caps (hba);ufs_qcom_advertise_quirks (hba); +ufs_qcom_set_bus_vote (hba, true);ufs_qcom_setup_clocks (hba, true,POST_CHANGE );if (hba->dev->id <MAX_UFS_QCOM_HOSTS )
Please add space after switch.
+ switch(status) {
+ case PRE_CHANGE
Re: [PATCH v9 3/7] scsi: ufs-qcom: Adjust bus bandwidth voting and unvoting
Quoted 176 lines · On 2020-02-11 11:09, [email protected] wrote:
Hi Can,
Quoted 158 lines · Can Guo
The bus bandwidth voting is required to be done before the bus clocks are enabled, and the unvoting is required to be done only after the bus clocks are disabled.
Signed-off-by Can Guo <[email protected]>Reviewed-by Asutosh Das <[email protected]>--- drivers/scsi/ufs/ufs-qcom.c | 78 ++++++++++++++++++++++++++++++--------------- 1 file changed, 53 insertions(+), 25 deletions(-)drivers/scsi/ufs/ufs-qcom.c +0
-1@@ -38,7 +38,6 @@ enum {static struct ufs_qcom_host *ufs_qcom_hosts[MAX_UFS_QCOM_HOSTS ]; -static int ufs_qcom_set_bus_vote (struct ufs_qcom_host *host,int vote);static void ufs_qcom_get_default_testbus_cfg (struct ufs_qcom_host *host);static int ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div(struct
ufs_hba
*hba,drivers/scsi/ufs/ufs-qcom.c +1
-1u32 clk_cycles);@@ -674,7 +673,7 @@ static void ufs_qcom_get_speed_mode(struct ufs_pa_layer_attr *p, char *result) } } -static int ufs_qcom_set_bus_vote(struct ufs_qcom_host *host, int vote) +static int __ufs_qcom_set_bus_vote(struct ufs_qcom_host *host, int vote){
drivers/scsi/ufs/ufs-qcom.c +30
-1int err =0 ;@@ -705,7 +704,7 @@ static int ufs_qcom_update_bus_bw_vote(struct ufs_qcom_host *host) vote =ufs_qcom_get_bus_vote (host, mode);if (vote >=0 ) - err =ufs_qcom_set_bus_vote (host, vote); + err =__ufs_qcom_set_bus_vote (host, vote);else err = vote;@@ -716,6 +715,35 @@ static int ufs_qcom_update_bus_bw_vote(struct ufs_qcom_host *host)return err; } +static int ufs_qcom_set_bus_vote (struct ufs_hba *hba,bool on) +{ +struct ufs_qcom_host *host =ufshcd_get_variant (hba); +int vote, err; + +/* +* In case ufs_qcom_init() is not yet done, simply ignore. +* This ufs_qcom_set_bus_vote() shall be called from +* ufs_qcom_init() after init is done. +*/ +if (!host) +return 0 ; + +if (on) { + vote = host->bus_vote.saved_vote; +if (vote == host->bus_vote.min_bw_vote) +ufs_qcom_update_bus_bw_vote (host); + }else { + vote = host->bus_vote.min_bw_vote; + } + + err =__ufs_qcom_set_bus_vote (host, vote); +if (err) +dev_err (hba->dev,"%s: set bus vote failed %d\n" , + __func__, err); + +return err; +} + static ssize_t show_ufs_to_mem_max_bus_bw(struct device *dev, struct
device_attribute*attr,drivers/scsi/ufs/ufs-qcom.c +1
-1char *buf)@@ -792,7 +820,7 @@ static int ufs_qcom_update_bus_bw_vote(struct ufs_qcom_host *host)return 0 ; } -static int ufs_qcom_set_bus_vote (struct ufs_qcom_host *host,int vote) +static int ufs_qcom_set_bus_vote(struct ufs_hba *host, bool on) {drivers/scsi/ufs/ufs-qcom.c +1
-2return 0 ; }@@ -1030,8 +1058,7 @@ static int ufs_qcom_setup_clocks(struct ufs_hba *hba, bool on, enum ufs_notify_change_status status) {struct ufs_qcom_host *host =ufshcd_get_variant (hba); -int err; -int vote =0 ; +int err =0 ;/* drivers/scsi/ufs/ufs-qcom.c +19
-19* In case ufs_qcom_init() is not yet done, simply ignore. @@ -1041,28 +1068,28 @@ static int ufs_qcom_setup_clocks(struct ufs_hba *hba, bool on, if (!host) return 0; - if (on && (status == POST_CHANGE)) { - /* enable the device ref clock for HS mode*/ - if (ufshcd_is_hs_mode(&hba->pwr_info)) - ufs_qcom_dev_ref_clk_ctrl(host, true); - vote = host->bus_vote.saved_vote; -if (vote == host->bus_vote.min_bw_vote) -ufs_qcom_update_bus_bw_vote (host); - - }else if (!on && (status ==PRE_CHANGE )) { -if (!ufs_qcom_is_link_active (hba)) { -/* disable device ref_clk */ -ufs_qcom_dev_ref_clk_ctrl (host, false); +switch (status) { +case PRE_CHANGE : +if (on) { + err =ufs_qcom_set_bus_vote (hba, true); + }else { +if (!ufs_qcom_is_link_active (hba)) { +/* disable device ref_clk */ +ufs_qcom_dev_ref_clk_ctrl (host, false); + } } - - vote = host->bus_vote.min_bw_vote; +break ; +case POST_CHANGE : +if (on) { +/* enable the device ref clock for HS mode*/ +if (ufshcd_is_hs_mode (&hba->pwr_info)) +ufs_qcom_dev_ref_clk_ctrl (host, true); + }else { + err =ufs_qcom_set_bus_vote (hba, false); + } +break ; } - err =ufs_qcom_set_bus_vote (host, vote); -if (err) -dev_err (hba->dev,"%s: set bus vote failed %d\n" , - __func__, err); -return err; }drivers/scsi/ufs/ufs-qcom.c static int ufs_qcom_init(struct ufs_hba *hba) · line 1271
Quoted 7 lines
drivers/scsi/ufs/ufs-qcom.c +1
-0@@ -1238,6 +1265,7 @@ static int ufs_qcom_init(struct ufs_hba *hba)ufs_qcom_set_caps (hba);ufs_qcom_advertise_quirks (hba); +ufs_qcom_set_bus_vote (hba, true);ufs_qcom_setup_clocks (hba, true,POST_CHANGE );if (hba->dev->id <MAX_UFS_QCOM_HOSTS )Please add space after switch.
(quoted diff) +2
-0+ switch(status) { + case PRE_CHANGE
Quoted 1 line
Reviewed-by Hongwu Su <[email protected]>
Thanks.
Can Guo.
PATCH v9 4/7 scsi: ufs: Remove the check before call setup clock notify vops
In reply to Can GuoThe functionality of vendor specific ops should be handled properly in platform specific driver, but should not count on the UFS driver.
--- drivers/scsi/ufs/ufshcd.c | 26 ++++++-------------------- 1 file changed, 6 insertions(+), 20 deletions(-)
drivers/scsi/ufs/ufshcd.c +6 -20
@@ -7402,16 +7402,9 @@ static int __ufshcd_setup_clocks(struct ufs_hba *hba, bool on,if (list_empty (head)) goto out; -/* -* vendor specific setup_clocks ops may depend on clocks managed by -* this standard driver hence call the vendor specific setup_clocks -* before disabling the clocks managed here. -*/ -if (!on) { - ret =ufshcd_vops_setup_clocks (hba, on,PRE_CHANGE ); -if (ret) -return ret; - } + ret =ufshcd_vops_setup_clocks (hba, on,PRE_CHANGE ); +if (ret) +return ret;list_for_each_entry (clki, head, list) {if (!IS_ERR_OR_NULL (clki->clk)) {
@@ -7435,16 +7428,9 @@ static int __ufshcd_setup_clocks(struct ufs_hba *hba, bool on, } } -/* -* vendor specific setup_clocks ops may depend on clocks managed by -* this standard driver hence call the vendor specific setup_clocks -* after enabling the clocks managed here. -*/ -if (on) { - ret =ufshcd_vops_setup_clocks (hba, on,POST_CHANGE ); -if (ret) -return ret; - } + ret =ufshcd_vops_setup_clocks (hba, on,POST_CHANGE ); +if (ret) +return ret; out:if (ret) {
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
PATCH v9 5/7 scsi: ufs: Fix ufshcd_hold() caused scheduling while atomic
In reply to Can GuoThe async version of ufshcd_hold(async == true), which is only called in queuecommand path as for now, is expected to work in atomic context, thus it should not sleep or schedule out. When it runs into the condition that clocks are ON but link is still in hibern8 state, it should bail out without flushing the clock ungate work.
--- drivers/scsi/ufs/ufshcd.c | 5 +++++ 1 file changed, 5 insertions(+)
drivers/scsi/ufs/ufshcd.c +5 -0
@@ -1518,6 +1518,11 @@ int ufshcd_hold(struct ufs_hba *hba, bool async)*/ if (ufshcd_can_hibern8_during_gating (hba) &&ufshcd_is_link_hibern8 (hba)) { +if (async) { + rc = -EAGAIN ; + hba->clk_gating.active_reqs--; +break ; + }spin_unlock_irqrestore (hba->host->host_lock, flags);flush_work (&hba->clk_gating.ungate_work);spin_lock_irqsave (hba->host->host_lock, flags);
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
PATCH v9 6/7 scsi: ufs: Add dev ref clock gating wait time support
In reply to Can GuoIn UFS version 3.0, a newly added attribute bRefClkGatingWaitTime defines the minimum time for which the reference clock is required by device during transition to LS-MODE or HIBERN8 state. Make this change to reflect the new requirement by adding delays before turning off the clock.
--- drivers/scsi/ufs/ufs.h | 3 +++ drivers/scsi/ufs/ufshcd.c | 34 ++++++++++++++++++++++++++++++++++ 2 files changed, 37 insertions(+)
drivers/scsi/ufs/ufs.h +3 -0
@@ -167,6 +167,7 @@ enum attr_idn {QUERY_ATTR_IDN_FFU_STATUS =0x14 ,QUERY_ATTR_IDN_PSA_STATE =0x15 ,QUERY_ATTR_IDN_PSA_DATA_SIZE =0x16 , + QUERY_ATTR_IDN_REF_CLK_GATING_WAIT_TIME = 0x17, };/* Descriptor idn for Query requests */
@@ -534,6 +535,8 @@ struct ufs_dev_info {u16 wmanufacturerid;/*UFS device Product Name */ u8 *model; +u16 wspecversion; +u32 clk_gating_wait_us; };/**
drivers/scsi/ufs/ufshcd.c +34 -0
@@ -91,6 +91,9 @@/* default delay of autosuspend: 2000 ms */ #define RPM_AUTOSUSPEND_DELAY_MS 2000 +/* Default value of wait time before gating device ref clock */ +#define UFSHCD_REF_CLK_GATING_WAIT_US 0xFF/* microsecs */ +#define ufshcd_toggle_vreg (_dev, _vreg, _on) \ ({ \ int _ret; \
@@ -3281,6 +3284,31 @@ static inline int ufshcd_read_unit_desc_param(struct ufs_hba *hba, param_offset, param_read_buf, param_size); } +static int ufshcd_get_ref_clk_gating_wait (struct ufs_hba *hba) +{ +int err =0 ; +u32 gating_wait =UFSHCD_REF_CLK_GATING_WAIT_US ; + +if (hba->dev_info.wspecversion >=0x300 ) { + err =ufshcd_query_attr_retry (hba,UPIU_QUERY_OPCODE_READ_ATTR , +QUERY_ATTR_IDN_REF_CLK_GATING_WAIT_TIME ,0 ,0 , + &gating_wait); +if (err) +dev_err (hba->dev,"Failed reading bRefClkGatingWait. err = %d, use default %uus\n" , + err, gating_wait); + +if (gating_wait ==0 ) { + gating_wait =UFSHCD_REF_CLK_GATING_WAIT_US ; +dev_err (hba->dev,"Undefined ref clk gating wait time, use default %uus\n" , + gating_wait); + } + + hba->dev_info.clk_gating_wait_us = gating_wait; + } + +return err; +} +/** * ufshcd_memory_alloc - allocate memory for host memory space data structures * @hba: per adapter instance
@@ -6626,6 +6654,10 @@ static int ufs_get_device_desc(struct ufs_hba *hba) dev_info->wmanufacturerid = desc_buf[DEVICE_DESC_PARAM_MANF_ID ] <<8 | desc_buf[DEVICE_DESC_PARAM_MANF_ID +1 ]; +/* getting Specification Version in big endian format */ + dev_info->wspecversion = desc_buf[DEVICE_DESC_PARAM_SPEC_VER ] <<8 | + desc_buf[DEVICE_DESC_PARAM_SPEC_VER +1 ]; + model_index = desc_buf[DEVICE_DESC_PARAM_PRDCT_NAME ]; err =ufshcd_read_string_desc (hba, model_index, &dev_info->model,SD_ASCII_STD );
@@ -7003,6 +7035,8 @@ static int ufshcd_device_params_init(struct ufs_hba *hba) goto out; } +ufshcd_get_ref_clk_gating_wait (hba); +ufs_fixup_device_setup (hba); if (!ufshcd_query_flag_retry(hba, UPIU_QUERY_OPCODE_READ_FLAG,
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
PATCH v9 7/7 scsi: ufs-qcom: Delay specific time before gate ref clk
In reply to Can GuoAfter enter hibern8, as UFS JEDEC ver 3.0 requires, a specific gating wait time is required before disable the device reference clock. If it is not specified, use the old delay.
--- drivers/scsi/ufs/ufs-qcom.c | 22 +++++++++++++++++++--- 1 file changed, 19 insertions(+), 3 deletions(-)
drivers/scsi/ufs/ufs-qcom.c +19 -3
@@ -845,11 +845,27 @@ static void ufs_qcom_dev_ref_clk_ctrl(struct ufs_qcom_host *host, bool enable)/* * If we are here to disable this clock it might be immediately * after entering into hibern8 in which case we need to make -* sure that device ref_clk is active at least 1us after the +* sure that device ref_clk is active for specific time after * hibern8 enter. */ -if (!enable) -udelay (1 ); +if (!enable) { +unsigned long gating_wait; + + gating_wait = host->hba->dev_info.clk_gating_wait_us; +if (!gating_wait) { +udelay (1 ); + }else { +/* +* bRefClkGatingWaitTime defines the minimum +* time for which the reference clock is +* required by device during transition from +* HS-MODE to LS-MODE or HIBERN8 state. Give it +* more delay to be on the safe side. +*/ + gating_wait +=10 ; +usleep_range (gating_wait, gating_wait +10 ); + } + }writel_relaxed (temp, host->dev_ref_clk_ctrl_mmio);
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project