Skip to contentSkip to conversation

arm64: dts: ipq6018: Add a few device nodes

PATCH Applied Sivaprakash Murugesan 2 participants 2 messages Feb 20, 2020 – Feb 28, 2020

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 arm64: dts: ipq6018: Add a few device nodes

add i2c, spi, crypto, rng, watchdog, peripheral nodes, also add support for wcss Q6 remoteproc driver and enable hw mutex, smem, mailbox, smp2p and rpmsg drivers

---
[V2] * Addressed review comments from Stephen This patch depends on Sricharan's ipq6018 dts patch
https://patchwork.kernel.org/patch/11340681/

 arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts |  34 ++++
 arch/arm64/boot/dts/qcom/ipq6018.dtsi        | 226 +++++++++++++++++++++++++++
 2 files changed, 260 insertions(+)
arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts +34 -0
index 897b4b2..b31117a 100644
@@ -28,3 +28,37 @@
 	pinctrl-names = "default";
 	status = "ok";
 };
+
+&i2c_1 {
+	pinctrl-0 = <&i2c_1_pins>;
+	pinctrl-names = "default";
+	status = "ok";
+};
+
+&spi_0 {
+	cs-select = <0>;
+	status = "ok";
+
+	m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		compatible = "n25q128a11";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&tlmm {
+	i2c_1_pins: i2c-1-pins {
+		pins = "gpio42", "gpio43";
+		function = "blsp2_i2c";
+		drive-strength = <8>;
+	};
+
+	spi_0_pins: spi-0-pins {
+		pins = "gpio38", "gpio39", "gpio40", "gpio41";
+		function = "blsp0_spi";
+		drive-strength = <8>;
+		bias-pull-down;
+	};
+};
arch/arm64/boot/dts/qcom/ipq6018.dtsi +226 -0

273 lines not on this page · raw message

Signature · 1 line
2.7.4
#1 lore raw
Quoted 5 lines · Sivaprakash Murugesan

add i2c, spi, crypto, rng, watchdog, peripheral nodes, also add support for wcss Q6 remoteproc driver and enable hw mutex, smem, mailbox, smp2p and rpmsg drivers

Applied, thank you.

Quoted 338 lines

---
[V2] * Addressed review comments from Stephen This patch depends on Sricharan's ipq6018 dts patch
https://patchwork.kernel.org/patch/11340681/

 arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts |  34 ++++
 arch/arm64/boot/dts/qcom/ipq6018.dtsi        | 226 +++++++++++++++++++++++++++
 2 files changed, 260 insertions(+)
arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts +34 -0
index 897b4b2..b31117a 100644
@@ -28,3 +28,37 @@
 	pinctrl-names = "default";
 	status = "ok";
 };
+
+&i2c_1 {
+	pinctrl-0 = <&i2c_1_pins>;
+	pinctrl-names = "default";
+	status = "ok";
+};
+
+&spi_0 {
+	cs-select = <0>;
+	status = "ok";
+
+	m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		compatible = "n25q128a11";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&tlmm {
+	i2c_1_pins: i2c-1-pins {
+		pins = "gpio42", "gpio43";
+		function = "blsp2_i2c";
+		drive-strength = <8>;
+	};
+
+	spi_0_pins: spi-0-pins {
+		pins = "gpio38", "gpio39", "gpio40", "gpio41";
+		function = "blsp0_spi";
+		drive-strength = <8>;
+		bias-pull-down;
+	};
+};
arch/arm64/boot/dts/qcom/ipq6018.dtsi +226 -0
index 0fb44e5..1aa8d85 100644
@@ -7,6 +7,7 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-ipq6018.h>
+#include <dt-bindings/reset/qcom,gcc-ipq6018.h>
 
 / {
 	#address-cells = <2>;
@@ -69,6 +70,18 @@
 		};
 	};
 
+	firmware {
+		scm {
+			compatible = "qcom,scm";
+		};
+	};
+
+	tcsr_mutex: hwlock {
+		compatible = "qcom,tcsr-mutex";
+		syscon = <&tcsr_mutex_regs 0 0x80>;
+		#hwlock-cells = <1>;
+	};
+
 	pmuv8: pmu {
 		compatible = "arm,cortex-a53-pmu";
 		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
@@ -89,6 +102,22 @@
 			reg = <0x0 0x48500000 0x0 0x00200000>;
 			no-map;
 		};
+
+		smem_region: memory@4aa00000 {
+			reg = <0x0 0x4aa00000 0x0 0x00100000>;
+			no-map;
+		};
+
+		q6_region: memory@4ab00000 {
+			reg = <0x0 0x4ab00000 0x0 0x02800000>;
+			no-map;
+		};
+	};
+
+	smem {
+		compatible = "qcom,smem";
+		memory-region = <&smem_region>;
+		hwlocks = <&tcsr_mutex 0>;
 	};
 
 	soc: soc {
@@ -98,6 +127,36 @@
 		dma-ranges;
 		compatible = "simple-bus";
 
+		prng: qrng@e1000 {
+			compatible = "qcom,prng-ee";
+			reg = <0xe3000 0x1000>;
+			clocks = <&gcc GCC_PRNG_AHB_CLK>;
+			clock-names = "core";
+		};
+
+		cryptobam: dma@704000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x00704000 0x20000>;
+			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_CRYPTO_AHB_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <1>;
+			qcom,controlled-remotely = <1>;
+			qcom,config-pipe-trust-reg = <0>;
+		};
+
+		crypto: crypto@73a000 {
+			compatible = "qcom,crypto-v5.1";
+			reg = <0x0073a000 0x6000>;
+			clocks = <&gcc GCC_CRYPTO_AHB_CLK>,
+				<&gcc GCC_CRYPTO_AXI_CLK>,
+				<&gcc GCC_CRYPTO_CLK>;
+			clock-names = "iface", "bus", "core";
+			dmas = <&cryptobam 2>, <&cryptobam 3>;
+			dma-names = "rx", "tx";
+		};
+
 		tlmm: pinctrl@1000000 {
 			compatible = "qcom,ipq6018-pinctrl";
 			reg = <0x01000000 0x300000>;
@@ -125,6 +184,26 @@
 			#reset-cells = <1>;
 		};
 
+		tcsr_mutex_regs: syscon@1905000 {
+			compatible = "syscon";
+			reg = <0x01905000 0x8000>;
+		};
+
+		tcsr_q6: syscon@1945000 {
+			compatible = "syscon";
+			reg = <0x01945000 0xe000>;
+		};
+
+		blsp_dma: dma@7884000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x07884000 0x2b000>;
+			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
 		blsp1_uart3: serial@78b1000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
 			reg = <0x078b1000 0x200>;
@@ -135,6 +214,66 @@
 			status = "disabled";
 		};
 
+		spi_0: spi@78b5000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x078b5000 0x600>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			spi-max-frequency = <50000000>;
+			clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
+				<&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 12>, <&blsp_dma 13>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		spi_1: spi@78b6000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x078b6000 0x600>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			spi-max-frequency = <50000000>;
+			clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
+				<&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		i2c_0: i2c@78b6000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x078b6000 0x600>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+				<&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
+			clock-names = "iface", "core";
+			clock-frequency  = <400000>;
+			dmas = <&blsp_dma 15>, <&blsp_dma 14>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2c_1: i2c@78b7000 { /* BLSP1 QUP2 */
+			compatible = "qcom,i2c-qup-v2.2.1";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x078b7000 0x600>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+				<&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
+			clock-names = "iface", "core";
+			clock-frequency  = <400000>;
+			dmas = <&blsp_dma 17>, <&blsp_dma 16>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
 		intc: interrupt-controller@b000000 {
 			compatible = "qcom,msm-qgic2";
 			interrupt-controller;
@@ -146,6 +285,21 @@
 			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
+		watchdog@b017000 {
+			compatible = "qcom,kpss-wdt";
+			interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
+			reg = <0x0b017000 0x40>;
+			clocks = <&sleep_clk>;
+			timeout-sec = <10>;
+		};
+
+		apcs_glb: mailbox@b111000 {
+			compatible = "qcom,ipq8074-apcs-apps-global";
+			reg = <0x0b111000 0xc>;
+
+			#mbox-cells = <1>;
+		};
+
 		timer {
 			compatible = "arm,armv8-timer";
 			interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
@@ -213,5 +367,77 @@
 			};
 		};
 
+		q6v5_wcss: remoteproc@cd00000 {
+			compatible = "qcom,ipq8074-wcss-pil";
+			reg = <0x0cd00000 0x4040>,
+				<0x004ab000 0x20>;
+			reg-names = "qdsp6",
+				    "rmb";
+			interrupts-extended = <&intc GIC_SPI 325 IRQ_TYPE_EDGE_RISING>,
+					      <&wcss_smp2p_in 0 0>,
+					      <&wcss_smp2p_in 1 0>,
+					      <&wcss_smp2p_in 2 0>,
+					      <&wcss_smp2p_in 3 0>;
+			interrupt-names = "wdog",
+					  "fatal",
+					  "ready",
+					  "handover",
+					  "stop-ack";
+
+			resets = <&gcc GCC_WCSSAON_RESET>,
+				 <&gcc GCC_WCSS_BCR>,
+				 <&gcc GCC_WCSS_Q6_BCR>;
+
+			reset-names = "wcss_aon_reset",
+				      "wcss_reset",
+				      "wcss_q6_reset";
+
+			clocks = <&gcc GCC_PRNG_AHB_CLK>;
+			clock-names = "prng";
+
+			qcom,halt-regs = <&tcsr_q6 0xa000 0xd000 0x0>;
+
+			qcom,smem-states = <&wcss_smp2p_out 0>,
+					   <&wcss_smp2p_out 1>;
+			qcom,smem-state-names = "shutdown",
+						"stop";
+
+			memory-region = <&q6_region>;
+
+			glink-edge {
+				interrupts = <GIC_SPI 321 IRQ_TYPE_EDGE_RISING>;
+				qcom,remote-pid = <1>;
+				mboxes = <&apcs_glb 8>;
+
+				qrtr_requests {
+					qcom,glink-channels = "IPCRTR";
+				};
+			};
+		};
+
+	};
+
+	wcss: wcss-smp2p {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <GIC_SPI 322 IRQ_TYPE_EDGE_RISING>;
+
+		mboxes = <&apcs_glb 9>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		wcss_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		wcss_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
 	};
 };
Signature · 1 line
2.7.4