Skip to contentSkip to conversation

net: dsa: mt7530: move mt7623 settings out off the mt7530

PATCH Applied [email protected] 4 participants 8 messages Apr 5, 2020 – Jul 29, 2020

Subsystems (7)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/2 net: dsa: mt7530: move mt7623 settings out off the mt7530

From: René van Dorst <[email protected]>

Moving mt7623 logic out off mt7530, is required to make hardware setting consistent after we introduce phylink to mtk driver.

Fixes ca366d6c889b ("net: dsa: mt7530: Convert to PHYLINK API")

---
v1 -> v2: no change

---
 drivers/net/dsa/mt7530.c | 85 ----------------------------------------
 drivers/net/dsa/mt7530.h | 10 -----
 2 files changed, 95 deletions(-)
drivers/net/dsa/mt7530.c +0 -85
index 2d0d91db0ddb..84391c8a0e16 100644
@@ -66,58 +66,6 @@ static const struct mt7530_mib_desc mt7530_mib[] = {
 	MIB_DESC(1, 0xb8, "RxArlDrop"),
 };
 
-static int
-mt7623_trgmii_write(struct mt7530_priv *priv,  u32 reg, u32 val)
-{
-	int ret;
-
-	ret =  regmap_write(priv->ethernet, TRGMII_BASE(reg), val);
-	if (ret < 0)
-		dev_err(priv->dev,
-			"failed to priv write register\n");
-	return ret;
-}
-
-static u32
-mt7623_trgmii_read(struct mt7530_priv *priv, u32 reg)
-{
-	int ret;
-	u32 val;
-
-	ret = regmap_read(priv->ethernet, TRGMII_BASE(reg), &val);
-	if (ret < 0) {
-		dev_err(priv->dev,
-			"failed to priv read register\n");
-		return ret;
-	}
-
-	return val;
-}
-
-static void
-mt7623_trgmii_rmw(struct mt7530_priv *priv, u32 reg,
-		  u32 mask, u32 set)
-{
-	u32 val;
-
-	val = mt7623_trgmii_read(priv, reg);
-	val &= ~mask;
-	val |= set;
-	mt7623_trgmii_write(priv, reg, val);
-}
-
-static void
-mt7623_trgmii_set(struct mt7530_priv *priv, u32 reg, u32 val)
-{
-	mt7623_trgmii_rmw(priv, reg, 0, val);
-}
-
-static void
-mt7623_trgmii_clear(struct mt7530_priv *priv, u32 reg, u32 val)
-{
-	mt7623_trgmii_rmw(priv, reg, val, 0);
-}
-
 static int
 core_read_mmd_indirect(struct mt7530_priv *priv, int prtad, int devad)
 {
@@ -530,27 +478,6 @@ mt7530_pad_clk_setup(struct dsa_switch *ds, int mode)
 		for (i = 0 ; i < NUM_TRGMII_CTRL; i++)
 			mt7530_rmw(priv, MT7530_TRGMII_RD(i),
 				   RD_TAP_MASK, RD_TAP(16));
-	else
-		if (priv->id != ID_MT7621)
-			mt7623_trgmii_set(priv, GSW_INTF_MODE,
-					  INTF_MODE_TRGMII);
-
-	return 0;
-}
-
-static int
-mt7623_pad_clk_setup(struct dsa_switch *ds)
-{
-	struct mt7530_priv *priv = ds->priv;
-	int i;
-
-	for (i = 0 ; i < NUM_TRGMII_CTRL; i++)
-		mt7623_trgmii_write(priv, GSW_TRGMII_TD_ODT(i),
-				    TD_DM_DRVP(8) | TD_DM_DRVN(8));
-
-	mt7623_trgmii_set(priv, GSW_TRGMII_RCK_CTRL, RX_RST | RXC_DQSISEL);
-	mt7623_trgmii_clear(priv, GSW_TRGMII_RCK_CTRL, RX_RST);
-
 	return 0;
 }
 
@@ -1303,10 +1230,6 @@ mt7530_setup(struct dsa_switch *ds)
 	dn = dsa_to_port(ds, MT7530_CPU_PORT)->master->dev.of_node->parent;
 
 	if (priv->id == ID_MT7530) {
-		priv->ethernet = syscon_node_to_regmap(dn);
-		if (IS_ERR(priv->ethernet))
-			return PTR_ERR(priv->ethernet);
-
 		regulator_set_voltage(priv->core_pwr, 1000000, 1000000);
 		ret = regulator_enable(priv->core_pwr);
 		if (ret < 0) {
@@ -1468,14 +1391,6 @@ static void mt7530_phylink_mac_config(struct dsa_switch *ds, int port,
 		/* Setup TX circuit incluing relevant PAD and driving */
 		mt7530_pad_clk_setup(ds, state->interface);
 
-		if (priv->id == ID_MT7530) {
-			/* Setup RX circuit, relevant PAD and driving on the
-			 * host which must be placed after the setup on the
-			 * device side is all finished.
-			 */
-			mt7623_pad_clk_setup(ds);
-		}
-
 		priv->p6_interface = state->interface;
 		break;
 	default:
drivers/net/dsa/mt7530.h +0 -10
index ef9b52f3152b..4aef6024441b 100644
@@ -277,7 +277,6 @@ enum mt7530_vlan_port_attr {
 
 /* Registers for TRGMII on the both side */
 #define MT7530_TRGMII_RCK_CTRL		0x7a00
-#define GSW_TRGMII_RCK_CTRL		0x300
 #define  RX_RST				BIT(31)
 #define  RXC_DQSISEL			BIT(30)
 #define  DQSI1_TAP_MASK			(0x7f << 8)
@@ -286,31 +285,24 @@ enum mt7530_vlan_port_attr {
 #define  DQSI0_TAP(x)			((x) & 0x7f)
 
 #define MT7530_TRGMII_RCK_RTT		0x7a04
-#define GSW_TRGMII_RCK_RTT		0x304
 #define  DQS1_GATE			BIT(31)
 #define  DQS0_GATE			BIT(30)
 
 #define MT7530_TRGMII_RD(x)		(0x7a10 + (x) * 8)
-#define GSW_TRGMII_RD(x)		(0x310 + (x) * 8)
 #define  BSLIP_EN			BIT(31)
 #define  EDGE_CHK			BIT(30)
 #define  RD_TAP_MASK			0x7f
 #define  RD_TAP(x)			((x) & 0x7f)
 
-#define GSW_TRGMII_TXCTRL		0x340
 #define MT7530_TRGMII_TXCTRL		0x7a40
 #define  TRAIN_TXEN			BIT(31)
 #define  TXC_INV			BIT(30)
 #define  TX_RST				BIT(28)
 
 #define MT7530_TRGMII_TD_ODT(i)		(0x7a54 + 8 * (i))
-#define GSW_TRGMII_TD_ODT(i)		(0x354 + 8 * (i))
 #define  TD_DM_DRVP(x)			((x) & 0xf)
 #define  TD_DM_DRVN(x)			(((x) & 0xf) << 4)
 
-#define GSW_INTF_MODE			0x390
-#define  INTF_MODE_TRGMII		BIT(1)
-
 #define MT7530_TRGMII_TCK_CTRL		0x7a78
 #define  TCK_TAP(x)			(((x) & 0xf) << 8)
 
@@ -443,7 +435,6 @@ static const char *p5_intf_modes(unsigned int p5_interface)
  * @ds:			The pointer to the dsa core structure
  * @bus:		The bus used for the device and built-in PHY
  * @rstc:		The pointer to reset control used by MCM
- * @ethernet:		The regmap used for access TRGMII-based registers
  * @core_pwr:		The power supplied into the core
  * @io_pwr:		The power supplied into the I/O
  * @reset:		The descriptor for GPIO line tied to its reset pin
@@ -460,7 +451,6 @@ struct mt7530_priv {
 	struct dsa_switch	*ds;
 	struct mii_bus		*bus;
 	struct reset_control	*rstc;
-	struct regmap		*ethernet;
 	struct regulator	*core_pwr;
 	struct regulator	*io_pwr;
 	struct gpio_desc	*reset;
Signature · 1 line
2.25.1
#1 lore raw

PATCH v2 2/2 net: ethernet: mediatek: move mt7623 settings out off the mt7530

From: René van Dorst <[email protected]>

Moving mt7623 logic out off mt7530, is required to make hardware setting consistent after we introduce phylink to mtk driver.

Fixes b8fc9f30821e ("net: ethernet: mediatek: Add basic PHYLINK support")

---
v1 -> v2: split out logic changing mtk_gmac0_rgmii_adjust that should be
refined further and actualy belonged to separate patch.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 24 ++++++++++++++++++++-
 drivers/net/ethernet/mediatek/mtk_eth_soc.h |  8 +++++++
 2 files changed, 31 insertions(+), 1 deletion(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +23 -1
index 8d28f90acfe7..09047109d0da 100644
@@ -65,6 +65,17 @@ u32 mtk_r32(struct mtk_eth *eth, unsigned reg)
 	return __raw_readl(eth->base + reg);
 }
 
+u32 mtk_m32(struct mtk_eth *eth, u32 mask, u32 set, unsigned reg)
+{
+	u32 val;
+
+	val = mtk_r32(eth, reg);
+	val &= ~mask;
+	val |= set;
+	mtk_w32(eth, val, reg);
+	return reg;
+}
+
 static int mtk_mdio_busy_wait(struct mtk_eth *eth)
 {
 	unsigned long t_start = jiffies;
@@ -193,7 +204,7 @@ static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 	struct mtk_mac *mac = container_of(config, struct mtk_mac,
 					   phylink_config);
 	struct mtk_eth *eth = mac->hw;
-	u32 mcr_cur, mcr_new, sid;
+	u32 mcr_cur, mcr_new, sid, i;
 	int val, ge_mode, err;
 
 	/* MT76x8 has no hardware settings between for the MAC */
@@ -255,6 +266,17 @@ static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 				    PHY_INTERFACE_MODE_TRGMII)
 					mtk_gmac0_rgmii_adjust(mac->hw,
 							       state->speed);
+
+				/* mt7623_pad_clk_setup */
+				for (i = 0 ; i < NUM_TRGMII_CTRL; i++)
+					mtk_w32(mac->hw,
+						TD_DM_DRVP(8) | TD_DM_DRVN(8),
+						TRGMII_TD_ODT(i));
+
+				/* Assert/release MT7623 RXC reset */
+				mtk_m32(mac->hw, 0, RXC_RST | RXC_DQSISEL,
+					TRGMII_RCK_CTRL);
+				mtk_m32(mac->hw, RXC_RST, 0, TRGMII_RCK_CTRL);
 			}
 		}
 
drivers/net/ethernet/mediatek/mtk_eth_soc.h +8 -0
index 85830fe14a1b..454cfcd465fd 100644
@@ -352,10 +352,13 @@
 #define DQSI0(x)		((x << 0) & GENMASK(6, 0))
 #define DQSI1(x)		((x << 8) & GENMASK(14, 8))
 #define RXCTL_DMWTLAT(x)	((x << 16) & GENMASK(18, 16))
+#define RXC_RST			BIT(31)
 #define RXC_DQSISEL		BIT(30)
 #define RCK_CTRL_RGMII_1000	(RXC_DQSISEL | RXCTL_DMWTLAT(2) | DQSI1(16))
 #define RCK_CTRL_RGMII_10_100	RXCTL_DMWTLAT(2)
 
+#define NUM_TRGMII_CTRL		5
+
 /* TRGMII RXC control register */
 #define TRGMII_TCK_CTRL		0x10340
 #define TXCTL_DMWTLAT(x)	((x << 16) & GENMASK(18, 16))
@@ -363,6 +366,11 @@
 #define TCK_CTRL_RGMII_1000	TXCTL_DMWTLAT(2)
 #define TCK_CTRL_RGMII_10_100	(TXC_INV | TXCTL_DMWTLAT(2))
 
+/* TRGMII TX Drive Strength */
+#define TRGMII_TD_ODT(i)	(0x10354 + 8 * (i))
+#define  TD_DM_DRVP(x)		((x) & 0xf)
+#define  TD_DM_DRVN(x)		(((x) & 0xf) << 4)
+
 /* TRGMII Interface mode register */
 #define INTF_MODE		0x10390
 #define TRGMII_INTF_DIS		BIT(0)
Signature · 1 line
2.25.1
maintainer Applied
#2 lore raw

Re: [PATCH v2 net 2/2] net: ethernet: mediatek: move mt7623 settings out off the mt7530

From: <[email protected]>
Date: Mon, 6 Apr 2020 05:42:54 +0800

Quoted 5 lines

From: René van Dorst <[email protected]>

Moving mt7623 logic out off mt7530, is required to make hardware setting consistent after we introduce phylink to mtk driver.

Quoted 7 lines
Fixes b8fc9f30821e ("net: ethernet: mediatek: Add basic PHYLINK support")

---
v1 -> v2: split out logic changing mtk_gmac0_rgmii_adjust that should be
refined further and actualy belonged to separate patch.

Applied.

#4 lore raw

PATCH 1/1 net: ethernet: mtk_eth_soc: Always call mtk_gmac0_rgmii_adjust() for mt7623

From: René van Dorst <[email protected]>

Modify mtk_gmac0_rgmii_adjust() so it can always be called. mtk_gmac0_rgmii_adjust() sets-up the TRGMII clocks.

---

Quoted 4 lines · Frank Wunderlich

have tested these 2 and additional rene's 3rd Patch on my tree [1] on BPi-R2, no problem with trgmii yet (multiple power-cycle+reboots). I had issues with current 5.6.0 version, so imho these should go also into 5.6.y

Here's that third patch of which Frank speaks. I don't see it submitted yet, and I found I needed it on 5.4 too for the Ethernet to be functional.

 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 19 ++++++++++++++-----
 1 file changed, 14 insertions(+), 5 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +14 -5
index b5408c5b954a..f89f225ab144 100644
@@ -171,11 +171,21 @@ static int mt7621_gmac0_rgmii_adjust(struct mtk_eth *eth,
 	return 0;
 }
 
-static void mtk_gmac0_rgmii_adjust(struct mtk_eth *eth, int speed)
+static void mtk_gmac0_rgmii_adjust(struct mtk_eth *eth,
+				   phy_interface_t interface, int speed)
 {
 	u32 val;
 	int ret;
 
+	if (interface == PHY_INTERFACE_MODE_TRGMII) {
+		mtk_w32(eth, TRGMII_MODE, INTF_MODE);
+		val = 500000000;
+		ret = clk_set_rate(eth->clks[MTK_CLK_TRGPLL], val);
+		if (ret)
+			dev_err(eth->dev, "Failed to set trgmii pll: %d\n", ret);
+		return;
+	}
+
 	val = (speed == SPEED_1000) ?
 		INTF_MODE_RGMII_1000 : INTF_MODE_RGMII_10_100;
 	mtk_w32(eth, val, INTF_MODE);
@@ -262,10 +272,9 @@ static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 							      state->interface))
 					goto err_phy;
 			} else {
-				if (state->interface !=
-				    PHY_INTERFACE_MODE_TRGMII)
-					mtk_gmac0_rgmii_adjust(mac->hw,
-							       state->speed);
+				mtk_gmac0_rgmii_adjust(mac->hw,
+						       state->interface,
+						       state->speed);
 
 				/* mt7623_pad_clk_setup */
 				for (i = 0 ; i < NUM_TRGMII_CTRL; i++)
maintainer Applied
#5 lore raw

Re: [PATCH] net: ethernet: mtk_eth_soc: Always call mtk_gmac0_rgmii_adjust() for mt7623

From: David Woodhouse <[email protected]>
Date: Thu, 23 Jul 2020 20:07:10 +0100

Quoted 8 lines

From: René van Dorst <[email protected]>

Modify mtk_gmac0_rgmii_adjust() so it can always be called. mtk_gmac0_rgmii_adjust() sets-up the TRGMII clocks.

Applied.

#6 lore raw

Aw: Re: [PATCH] net: ethernet: mtk_eth_soc: Always call mtk_gmac0_rgmii_adjust() for mt7623

Hi,

Thank you David's to get this finally applied. Add recipient for stable tree as TRGMII on 5.4+ is also broken without this Patch.

regards Frank

Quoted 2 lines

Gesendet: Mittwoch, 29. Juli 2020 um 02:05 Uhr
Von: "David Miller" <[email protected]>

Applied.

maintainer Applied
#7 lore raw
In reply to [email protected]

From: <[email protected]>
Date: Mon, 6 Apr 2020 05:42:53 +0800

Quoted 9 lines

From: René van Dorst <[email protected]>

Moving mt7623 logic out off mt7530, is required to make hardware setting consistent after we introduce phylink to mtk driver.

Fixes ca366d6c889b ("net: dsa: mt7530: Convert to PHYLINK API")

Applied.