Skip to contentSkip to conversation

Enable SS/HS USB support on SM8150

PATCH In review Wesley Cheng 4 participants 6 messages Apr 11, 2020 – Jun 16, 2020

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

v4 cover Enable SS/HS USB support on SM8150

Add required device tree nodes to enable the USB SS and HS paths on the primary USB controller on SM8150. In addition, implement missing resources from the SM8150 GCC driver, which includes the USB GDSC and the USB PIPE clocks.

Changes in v4:
- Re-ordered compatible cells for usb_1_hsphy and usb_1 to select by the platform first.

Changes in v3:
- Set dr_mode to "peripheral" on the SM8150 MTP DTSI file.

Changes in v2:
- Combine GDSC and USB PIPE clock changes.
- Re-order DTS nodes based on address

Jack Pham (1):
arm64: dts: qcom: sm8150: Add USB and PHY device nodes

Wesley Cheng (1):
clk: qcom: gcc: Add USB3 PIPE clock and GDSC for SM8150

 arch/arm64/boot/dts/qcom/sm8150-mtp.dts     | 21 +++++++
 arch/arm64/boot/dts/qcom/sm8150.dtsi        | 92 +++++++++++++++++++++++++++++
 drivers/clk/qcom/gcc-sm8150.c               | 52 ++++++++++++++++
 include/dt-bindings/clock/qcom,gcc-sm8150.h |  4 ++
 4 files changed, 169 insertions(+)
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
#1 lore raw

PATCH v4 1/2 clk: qcom: gcc: Add USB3 PIPE clock and GDSC for SM8150

This adds the USB3 PIPE clock and GDSC structures, so that the USB driver can vote for these resources to be enabled/disabled when required. Both are needed for SS and HS USB paths to operate properly. The GDSC will allow the USB system to be brought out of reset, while the PIPE clock is needed for data transactions between the PHY and controller.

---
 drivers/clk/qcom/gcc-sm8150.c               | 52 +++++++++++++++++++++++++++++
 include/dt-bindings/clock/qcom,gcc-sm8150.h |  4 +++
 2 files changed, 56 insertions(+)
drivers/clk/qcom/gcc-sm8150.c +52 -0
index 2087721..ef98fdc 100644
@@ -21,6 +21,7 @@
 #include "clk-rcg.h"
 #include "clk-regmap.h"
 #include "reset.h"
+#include "gdsc.h"
 
 enum {
 	P_BI_TCXO,
@@ -3171,6 +3172,18 @@ enum {
 	},
 };
 
+static struct clk_branch gcc_usb3_prim_phy_pipe_clk = {
+	.halt_check = BRANCH_HALT_SKIP,
+	.clkr = {
+		.enable_reg = 0xf058,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gcc_usb3_prim_phy_pipe_clk",
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
 static struct clk_branch gcc_usb3_sec_clkref_clk = {
 	.halt_reg = 0x8c028,
 	.halt_check = BRANCH_HALT,
@@ -3218,6 +3231,18 @@ enum {
 	},
 };
 
+static struct clk_branch gcc_usb3_sec_phy_pipe_clk = {
+	.halt_check = BRANCH_HALT_SKIP,
+	.clkr = {
+		.enable_reg = 0x10058,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gcc_usb3_sec_phy_pipe_clk",
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
 /*
  * Clock ON depends on external parent 'config noc', so cant poll
  * delay and also mark as crtitical for video boot
@@ -3292,6 +3317,24 @@ enum {
 	},
 };
 
+static struct gdsc usb30_prim_gdsc = {
+		.gdscr = 0xf004,
+		.pd = {
+			.name = "usb30_prim_gdsc",
+		},
+		.pwrsts = PWRSTS_OFF_ON,
+		.flags = POLL_CFG_GDSCR,
+};
+
+static struct gdsc usb30_sec_gdsc = {
+		.gdscr = 0x10004,
+		.pd = {
+			.name = "usb30_sec_gdsc",
+		},
+		.pwrsts = PWRSTS_OFF_ON,
+		.flags = POLL_CFG_GDSCR,
+};
+
 static struct clk_regmap *gcc_sm8150_clocks[] = {
 	[GCC_AGGRE_NOC_PCIE_TBU_CLK] = &gcc_aggre_noc_pcie_tbu_clk.clkr,
 	[GCC_AGGRE_UFS_CARD_AXI_CLK] = &gcc_aggre_ufs_card_axi_clk.clkr,
@@ -3480,10 +3523,12 @@ enum {
 	[GCC_USB3_PRIM_PHY_AUX_CLK] = &gcc_usb3_prim_phy_aux_clk.clkr,
 	[GCC_USB3_PRIM_PHY_AUX_CLK_SRC] = &gcc_usb3_prim_phy_aux_clk_src.clkr,
 	[GCC_USB3_PRIM_PHY_COM_AUX_CLK] = &gcc_usb3_prim_phy_com_aux_clk.clkr,
+	[GCC_USB3_PRIM_PHY_PIPE_CLK] = &gcc_usb3_prim_phy_pipe_clk.clkr,
 	[GCC_USB3_SEC_CLKREF_CLK] = &gcc_usb3_sec_clkref_clk.clkr,
 	[GCC_USB3_SEC_PHY_AUX_CLK] = &gcc_usb3_sec_phy_aux_clk.clkr,
 	[GCC_USB3_SEC_PHY_AUX_CLK_SRC] = &gcc_usb3_sec_phy_aux_clk_src.clkr,
 	[GCC_USB3_SEC_PHY_COM_AUX_CLK] = &gcc_usb3_sec_phy_com_aux_clk.clkr,
+	[GCC_USB3_SEC_PHY_PIPE_CLK] = &gcc_usb3_sec_phy_pipe_clk.clkr,
 	[GCC_VIDEO_AHB_CLK] = &gcc_video_ahb_clk.clkr,
 	[GCC_VIDEO_AXI0_CLK] = &gcc_video_axi0_clk.clkr,
 	[GCC_VIDEO_AXI1_CLK] = &gcc_video_axi1_clk.clkr,
@@ -3527,6 +3572,11 @@ enum {
 	[GCC_USB_PHY_CFG_AHB2PHY_BCR] = { 0x6a000 },
 };
 
+static struct gdsc *gcc_sm8150_gdscs[] = {
+	[USB30_PRIM_GDSC] = &usb30_prim_gdsc,
+	[USB30_SEC_GDSC] = &usb30_sec_gdsc,
+};
+
 static const struct regmap_config gcc_sm8150_regmap_config = {
 	.reg_bits	= 32,
 	.reg_stride	= 4,
@@ -3541,6 +3591,8 @@ enum {
 	.num_clks = ARRAY_SIZE(gcc_sm8150_clocks),
 	.resets = gcc_sm8150_resets,
 	.num_resets = ARRAY_SIZE(gcc_sm8150_resets),
+	.gdscs = gcc_sm8150_gdscs,
+	.num_gdscs = ARRAY_SIZE(gcc_sm8150_gdscs),
 };
 
 static const struct of_device_id gcc_sm8150_match_table[] = {
include/dt-bindings/clock/qcom,gcc-sm8150.h +4 -0
index 90d60ef..3e1a918 100644
@@ -240,4 +240,8 @@
 #define GCC_USB30_SEC_BCR					27
 #define GCC_USB_PHY_CFG_AHB2PHY_BCR				28
 
+/* GCC GDSCRs */
+#define USB30_PRIM_GDSC                     4
+#define USB30_SEC_GDSC						5
+
 #endif
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Reviewed-by on v4 1/2
#2 lore raw

Re: [PATCH v4 1/2] clk: qcom: gcc: Add USB3 PIPE clock and GDSC for SM8150

Quoted 10 lines · Wesley Cheng

This adds the USB3 PIPE clock and GDSC structures, so that the USB driver can vote for these resources to be enabled/disabled when required. Both are needed for SS and HS USB paths to operate properly. The GDSC will allow the USB system to be brought out of reset, while the PIPE clock is needed for data transactions between the PHY and controller.

Stephen, let me know when you take this patch and I'll take the dts one.

Regards,
Bjorn

Quoted 130 lines
---
 drivers/clk/qcom/gcc-sm8150.c               | 52 +++++++++++++++++++++++++++++
 include/dt-bindings/clock/qcom,gcc-sm8150.h |  4 +++
 2 files changed, 56 insertions(+)
drivers/clk/qcom/gcc-sm8150.c +52 -0
index 2087721..ef98fdc 100644
@@ -21,6 +21,7 @@
 #include "clk-rcg.h"
 #include "clk-regmap.h"
 #include "reset.h"
+#include "gdsc.h"
 
 enum {
 	P_BI_TCXO,
@@ -3171,6 +3172,18 @@ enum {
 	},
 };
 
+static struct clk_branch gcc_usb3_prim_phy_pipe_clk = {
+	.halt_check = BRANCH_HALT_SKIP,
+	.clkr = {
+		.enable_reg = 0xf058,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gcc_usb3_prim_phy_pipe_clk",
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
 static struct clk_branch gcc_usb3_sec_clkref_clk = {
 	.halt_reg = 0x8c028,
 	.halt_check = BRANCH_HALT,
@@ -3218,6 +3231,18 @@ enum {
 	},
 };
 
+static struct clk_branch gcc_usb3_sec_phy_pipe_clk = {
+	.halt_check = BRANCH_HALT_SKIP,
+	.clkr = {
+		.enable_reg = 0x10058,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gcc_usb3_sec_phy_pipe_clk",
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
 /*
  * Clock ON depends on external parent 'config noc', so cant poll
  * delay and also mark as crtitical for video boot
@@ -3292,6 +3317,24 @@ enum {
 	},
 };
 
+static struct gdsc usb30_prim_gdsc = {
+		.gdscr = 0xf004,
+		.pd = {
+			.name = "usb30_prim_gdsc",
+		},
+		.pwrsts = PWRSTS_OFF_ON,
+		.flags = POLL_CFG_GDSCR,
+};
+
+static struct gdsc usb30_sec_gdsc = {
+		.gdscr = 0x10004,
+		.pd = {
+			.name = "usb30_sec_gdsc",
+		},
+		.pwrsts = PWRSTS_OFF_ON,
+		.flags = POLL_CFG_GDSCR,
+};
+
 static struct clk_regmap *gcc_sm8150_clocks[] = {
 	[GCC_AGGRE_NOC_PCIE_TBU_CLK] = &gcc_aggre_noc_pcie_tbu_clk.clkr,
 	[GCC_AGGRE_UFS_CARD_AXI_CLK] = &gcc_aggre_ufs_card_axi_clk.clkr,
@@ -3480,10 +3523,12 @@ enum {
 	[GCC_USB3_PRIM_PHY_AUX_CLK] = &gcc_usb3_prim_phy_aux_clk.clkr,
 	[GCC_USB3_PRIM_PHY_AUX_CLK_SRC] = &gcc_usb3_prim_phy_aux_clk_src.clkr,
 	[GCC_USB3_PRIM_PHY_COM_AUX_CLK] = &gcc_usb3_prim_phy_com_aux_clk.clkr,
+	[GCC_USB3_PRIM_PHY_PIPE_CLK] = &gcc_usb3_prim_phy_pipe_clk.clkr,
 	[GCC_USB3_SEC_CLKREF_CLK] = &gcc_usb3_sec_clkref_clk.clkr,
 	[GCC_USB3_SEC_PHY_AUX_CLK] = &gcc_usb3_sec_phy_aux_clk.clkr,
 	[GCC_USB3_SEC_PHY_AUX_CLK_SRC] = &gcc_usb3_sec_phy_aux_clk_src.clkr,
 	[GCC_USB3_SEC_PHY_COM_AUX_CLK] = &gcc_usb3_sec_phy_com_aux_clk.clkr,
+	[GCC_USB3_SEC_PHY_PIPE_CLK] = &gcc_usb3_sec_phy_pipe_clk.clkr,
 	[GCC_VIDEO_AHB_CLK] = &gcc_video_ahb_clk.clkr,
 	[GCC_VIDEO_AXI0_CLK] = &gcc_video_axi0_clk.clkr,
 	[GCC_VIDEO_AXI1_CLK] = &gcc_video_axi1_clk.clkr,
@@ -3527,6 +3572,11 @@ enum {
 	[GCC_USB_PHY_CFG_AHB2PHY_BCR] = { 0x6a000 },
 };
 
+static struct gdsc *gcc_sm8150_gdscs[] = {
+	[USB30_PRIM_GDSC] = &usb30_prim_gdsc,
+	[USB30_SEC_GDSC] = &usb30_sec_gdsc,
+};
+
 static const struct regmap_config gcc_sm8150_regmap_config = {
 	.reg_bits	= 32,
 	.reg_stride	= 4,
@@ -3541,6 +3591,8 @@ enum {
 	.num_clks = ARRAY_SIZE(gcc_sm8150_clocks),
 	.resets = gcc_sm8150_resets,
 	.num_resets = ARRAY_SIZE(gcc_sm8150_resets),
+	.gdscs = gcc_sm8150_gdscs,
+	.num_gdscs = ARRAY_SIZE(gcc_sm8150_gdscs),
 };
 
 static const struct of_device_id gcc_sm8150_match_table[] = {
include/dt-bindings/clock/qcom,gcc-sm8150.h +4 -0
index 90d60ef..3e1a918 100644
@@ -240,4 +240,8 @@
 #define GCC_USB30_SEC_BCR					27
 #define GCC_USB_PHY_CFG_AHB2PHY_BCR				28
 
+/* GCC GDSCRs */
+#define USB30_PRIM_GDSC                     4
+#define USB30_SEC_GDSC						5
+
 #endif
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
maintainer
#3 lore raw

Re: [PATCH v4 1/2] clk: qcom: gcc: Add USB3 PIPE clock and GDSC for SM8150

Quoting Bjorn Andersson (2020-04-10 18:01:43)

Quoted 10 lines · Wesley Cheng
Quoted 9 lines

This adds the USB3 PIPE clock and GDSC structures, so that the USB driver can vote for these resources to be enabled/disabled when required. Both are needed for SS and HS USB paths to operate properly. The GDSC will allow the USB system to be brought out of reset, while the PIPE clock is needed for data transactions between the PHY and controller.

Quoted 8 lines
Quoted 2 lines

Stephen, let me know when you take this patch and I'll take the dts one.

Looks like I already applied it and it's merged in Linus' tree.

#4 lore raw

PATCH v4 2/2 arm64: dts: qcom: sm8150: Add USB and PHY device nodes

In reply to Wesley Cheng

From: Jack Pham <[email protected]>

Add device nodes for the USB3 controller, QMP SS PHY and SNPS HS PHY.

---
 arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 21 ++++++++
 arch/arm64/boot/dts/qcom/sm8150.dtsi    | 92 +++++++++++++++++++++++++++++++++
 2 files changed, 113 insertions(+)
arch/arm64/boot/dts/qcom/sm8150-mtp.dts +21 -0
index 8ab1661..6c6325c 100644
@@ -408,3 +408,24 @@
 	vdda-pll-supply = <&vreg_l3c_1p2>;
 	vdda-pll-max-microamp = <19000>;
 };
+
+&usb_1_hsphy {
+	status = "okay";
+	vdda-pll-supply = <&vdd_usb_hs_core>;
+	vdda33-supply = <&vdda_usb_hs_3p1>;
+	vdda18-supply = <&vdda_usb_hs_1p8>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+	vdda-phy-supply = <&vreg_l3c_1p2>;
+	vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "peripheral";
+};
arch/arm64/boot/dts/qcom/sm8150.dtsi +92 -0

98 lines not on this page · raw message

Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
#5 lore raw

Re: [PATCH v4 2/2] arm64: dts: qcom: sm8150: Add USB and PHY device nodes

Quoted 4 lines · Wesley Cheng

From: Jack Pham <[email protected]>

Add device nodes for the USB3 controller, QMP SS PHY and SNPS HS PHY.

Bjorn, can you please review/pick this.. I dont see this in -rc1

Quoted 146 lines
---
 arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 21 ++++++++
 arch/arm64/boot/dts/qcom/sm8150.dtsi    | 92 +++++++++++++++++++++++++++++++++
 2 files changed, 113 insertions(+)
arch/arm64/boot/dts/qcom/sm8150-mtp.dts +21 -0
index 8ab1661..6c6325c 100644
@@ -408,3 +408,24 @@
 	vdda-pll-supply = <&vreg_l3c_1p2>;
 	vdda-pll-max-microamp = <19000>;
 };
+
+&usb_1_hsphy {
+	status = "okay";
+	vdda-pll-supply = <&vdd_usb_hs_core>;
+	vdda33-supply = <&vdda_usb_hs_3p1>;
+	vdda18-supply = <&vdda_usb_hs_1p8>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+	vdda-phy-supply = <&vreg_l3c_1p2>;
+	vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "peripheral";
+};
arch/arm64/boot/dts/qcom/sm8150.dtsi +92 -0
index 141c21d..a36512d 100644
@@ -621,6 +621,98 @@
 			};
 		};
 
+		usb_1_hsphy: phy@88e2000 {
+			compatible = "qcom,sm8150-usb-hs-phy",
+							"qcom,usb-snps-hs-7nm-phy";
+			reg = <0 0x088e2000 0 0x400>;
+			status = "disabled";
+			#phy-cells = <0>;
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+		};
+
+		usb_1_qmpphy: phy@88e9000 {
+			compatible = "qcom,sm8150-qmp-usb3-phy";
+			reg = <0 0x088e9000 0 0x18c>,
+			      <0 0x088e8000 0 0x10>;
+			reg-names = "reg-base", "dp_com";
+			status = "disabled";
+			#clock-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
+				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
+			clock-names = "aux", "ref_clk_src", "ref", "com_aux";
+
+			resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
+				 <&gcc GCC_USB3_PHY_PRIM_BCR>;
+			reset-names = "phy", "common";
+
+			usb_1_ssphy: lanes@88e9200 {
+				reg = <0 0x088e9200 0 0x200>,
+				      <0 0x088e9400 0 0x200>,
+				      <0 0x088e9c00 0 0x218>,
+				      <0 0x088e9600 0 0x200>,
+				      <0 0x088e9800 0 0x200>,
+				      <0 0x088e9a00 0 0x100>;
+				#phy-cells = <0>;
+				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb3_phy_pipe_clk_src";
+			};
+		};
+
+		usb_1: usb@a6f8800 {
+			compatible = "qcom,sm8150-dwc3", "qcom,dwc3";
+			reg = <0 0x0a6f8800 0 0x400>;
+			status = "disabled";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			dma-ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+				 <&gcc GCC_USB3_SEC_CLKREF_CLK>;
+			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+				      "sleep", "xo";
+
+			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <150000000>;
+
+			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hs_phy_irq", "ss_phy_irq",
+					  "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+			power-domains = <&gcc USB30_PRIM_GDSC>;
+
+			resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+			usb_1_dwc3: dwc3@a600000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a600000 0 0xcd00>;
+				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+			};
+		};
+
 		aoss_qmp: power-controller@c300000 {
 			compatible = "qcom,sm8150-aoss-qmp";
 			reg = <0x0 0x0c300000 0x0 0x100000>;
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Signature · 1 line
~Vinod