Skip to contentSkip to conversation

HID: mcp2221: add GPIO functionality support

PATCH Applied Rishi Gupta 3 participants 3 messages Apr 14, 2020 – Apr 16, 2020

Subsystems (3)
lore
Share & tools
lore

Rishi Gupta

author maintainer
#0 lore raw

PATCH 1/1 HID: mcp2221: add GPIO functionality support

MCP2221 has 4 pins that can be used as GPIO or configured for alternate functionality such as clock generation and IRQ detection. This patch adds support for GPIO functionality.

To set direction of a pin or to toggle its state after it has been configured as GPIO, driver sends command to mcp2221 and parses response received from mcp2221. Based on this response either 0 or appropriate error code is returned to GPIO framework.

To get the direction or current state of a pin, driver sends command and read response from the device. Based on the response received from device direction or value is sent to the GPIO framework.

Command from driver to mcp2221 device are output report. Response received from mcp2221 is input report.

Datasheet (page 45-48) contains details about how to decode the response received from device:
http://ww1.microchip.com/downloads/en/DeviceDoc/20005565B.pdf

---
 drivers/hid/hid-mcp2221.c | 169 ++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 169 insertions(+)
drivers/hid/hid-mcp2221.c +169 -0
index d958475..e1b93ce3 100644
@@ -15,6 +15,7 @@
 #include <linux/hid.h>
 #include <linux/hidraw.h>
 #include <linux/i2c.h>
+#include <linux/gpio/driver.h>
 #include "hid-ids.h"
 
 /* Commands codes in a raw output report */
@@ -27,6 +28,8 @@ enum {
 	MCP2221_I2C_PARAM_OR_STATUS	= 0x10,
 	MCP2221_I2C_SET_SPEED = 0x20,
 	MCP2221_I2C_CANCEL = 0x10,
+	MCP2221_GPIO_SET = 0x50,
+	MCP2221_GPIO_GET = 0x51,
 };
 
 /* Response codes in a raw input report */
@@ -42,6 +45,8 @@ enum {
 	MCP2221_I2C_WRADDRL_SEND = 0x21,
 	MCP2221_I2C_ADDR_NACK = 0x25,
 	MCP2221_I2C_READ_COMPL = 0x55,
+	MCP2221_ALT_F_NOT_GPIOV = 0xEE,
+	MCP2221_ALT_F_NOT_GPIOD = 0xEF,
 };
 
 /*
@@ -59,6 +64,9 @@ struct mcp2221 {
 	int rxbuf_idx;
 	int status;
 	u8 cur_i2c_clk_div;
+	struct gpio_chip *gc;
+	u8 gp_idx;
+	u8 gpio_dir;
 };
 
 /*
@@ -526,6 +534,110 @@ static const struct i2c_algorithm mcp_i2c_algo = {
 	.functionality = mcp_i2c_func,
 };
 
+static int mcp_gpio_get(struct gpio_chip *gc,
+				unsigned int offset)
+{
+	int ret;
+	struct mcp2221 *mcp = gpiochip_get_data(gc);
+
+	mcp->txbuf[0] = MCP2221_GPIO_GET;
+
+	mcp->gp_idx = (offset + 1) * 2;
+
+	mutex_lock(&mcp->lock);
+	ret = mcp_send_data_req_status(mcp, mcp->txbuf, 1);
+	mutex_unlock(&mcp->lock);
+
+	return ret;
+}
+
+static void mcp_gpio_set(struct gpio_chip *gc,
+				unsigned int offset, int value)
+{
+	struct mcp2221 *mcp = gpiochip_get_data(gc);
+
+	memset(mcp->txbuf, 0, 18);
+	mcp->txbuf[0] = MCP2221_GPIO_SET;
+
+	mcp->gp_idx = ((offset + 1) * 4) - 1;
+
+	mcp->txbuf[mcp->gp_idx - 1] = 1;
+	mcp->txbuf[mcp->gp_idx] = !!value;
+
+	mutex_lock(&mcp->lock);
+	mcp_send_data_req_status(mcp, mcp->txbuf, 18);
+	mutex_unlock(&mcp->lock);
+}
+
+static int mcp_gpio_dir_set(struct mcp2221 *mcp,
+				unsigned int offset, u8 val)
+{
+	memset(mcp->txbuf, 0, 18);
+	mcp->txbuf[0] = MCP2221_GPIO_SET;
+
+	mcp->gp_idx = (offset + 1) * 5;
+
+	mcp->txbuf[mcp->gp_idx - 1] = 1;
+	mcp->txbuf[mcp->gp_idx] = val;
+
+	return mcp_send_data_req_status(mcp, mcp->txbuf, 18);
+}
+
+static int mcp_gpio_direction_input(struct gpio_chip *gc,
+				unsigned int offset)
+{
+	int ret;
+	struct mcp2221 *mcp = gpiochip_get_data(gc);
+
+	mutex_lock(&mcp->lock);
+	ret = mcp_gpio_dir_set(mcp, offset, 0);
+	mutex_unlock(&mcp->lock);
+
+	return ret;
+}
+
+static int mcp_gpio_direction_output(struct gpio_chip *gc,
+				unsigned int offset, int value)
+{
+	int ret;
+	struct mcp2221 *mcp = gpiochip_get_data(gc);
+
+	mutex_lock(&mcp->lock);
+	ret = mcp_gpio_dir_set(mcp, offset, 1);
+	mutex_unlock(&mcp->lock);
+
+	/* Can't configure as output, bailout early */
+	if (ret)
+		return ret;
+
+	mcp_gpio_set(gc, offset, value);
+
+	return 0;
+}
+
+static int mcp_gpio_get_direction(struct gpio_chip *gc,
+				unsigned int offset)
+{
+	int ret;
+	struct mcp2221 *mcp = gpiochip_get_data(gc);
+
+	mcp->txbuf[0] = MCP2221_GPIO_GET;
+
+	mcp->gp_idx = (offset + 1) * 2;
+
+	mutex_lock(&mcp->lock);
+	ret = mcp_send_data_req_status(mcp, mcp->txbuf, 1);
+	mutex_unlock(&mcp->lock);
+
+	if (ret)
+		return ret;
+
+	if (mcp->gpio_dir)
+		return GPIO_LINE_DIRECTION_IN;
+
+	return GPIO_LINE_DIRECTION_OUT;
+}
+
 /* Gives current state of i2c engine inside mcp2221 */
 static int mcp_get_i2c_eng_state(struct mcp2221 *mcp,
 				u8 *data, u8 idx)
@@ -638,6 +750,39 @@ static int mcp2221_raw_event(struct hid_device *hdev,
 		complete(&mcp->wait_in_report);
 		break;
 
+	case MCP2221_GPIO_GET:
+		switch (data[1]) {
+		case MCP2221_SUCCESS:
+			if ((data[mcp->gp_idx] == MCP2221_ALT_F_NOT_GPIOV) ||
+				(data[mcp->gp_idx + 1] == MCP2221_ALT_F_NOT_GPIOD)) {
+				mcp->status = -ENOENT;
+			} else {
+				mcp->status = !!data[mcp->gp_idx];
+				mcp->gpio_dir = !!data[mcp->gp_idx + 1];
+			}
+			break;
+		default:
+			mcp->status = -EAGAIN;
+		}
+		complete(&mcp->wait_in_report);
+		break;
+
+	case MCP2221_GPIO_SET:
+		switch (data[1]) {
+		case MCP2221_SUCCESS:
+			if ((data[mcp->gp_idx] == MCP2221_ALT_F_NOT_GPIOV) ||
+				(data[mcp->gp_idx - 1] == MCP2221_ALT_F_NOT_GPIOV)) {
+				mcp->status = -ENOENT;
+			} else {
+				mcp->status = 0;
+			}
+			break;
+		default:
+			mcp->status = -EAGAIN;
+		}
+		complete(&mcp->wait_in_report);
+		break;
+
 	default:
 		mcp->status = -EIO;
 		complete(&mcp->wait_in_report);
@@ -702,8 +847,32 @@ static int mcp2221_probe(struct hid_device *hdev,
 	}
 	i2c_set_adapdata(&mcp->adapter, mcp);
 
+	/* Setup GPIO chip */
+	mcp->gc = devm_kzalloc(&hdev->dev, sizeof(*mcp->gc), GFP_KERNEL);
+	if (!mcp->gc) {
+		ret = -ENOMEM;
+		goto err_gc;
+	}
+
+	mcp->gc->label = "mcp2221_gpio";
+	mcp->gc->direction_input = mcp_gpio_direction_input;
+	mcp->gc->direction_output = mcp_gpio_direction_output;
+	mcp->gc->get_direction = mcp_gpio_get_direction;
+	mcp->gc->set = mcp_gpio_set;
+	mcp->gc->get = mcp_gpio_get;
+	mcp->gc->ngpio = 4;
+	mcp->gc->base = -1;
+	mcp->gc->can_sleep = 1;
+	mcp->gc->parent = &hdev->dev;
+
+	ret = devm_gpiochip_add_data(&hdev->dev, mcp->gc, mcp);
+	if (ret)
+		goto err_gc;
+
 	return 0;
 
+err_gc:
+	i2c_del_adapter(&mcp->adapter);
 err_i2c:
 	hid_hw_close(mcp->hdev);
 err_hstop:
Signature · 1 line
2.7.4
Reviewed-by on v1 1/1
#1 lore raw
Quoted 15 lines · Rishi Gupta

MCP2221 has 4 pins that can be used as GPIO or configured for alternate functionality such as clock generation and IRQ detection. This patch adds support for GPIO functionality.

To set direction of a pin or to toggle its state after it has been configured as GPIO, driver sends command to mcp2221 and parses response received from mcp2221. Based on this response either 0 or appropriate error code is returned to GPIO framework.

To get the direction or current state of a pin, driver sends command and read response from the device. Based on the response received from device direction or value is sent to the GPIO framework.

Quoted 8 lines

Command from driver to mcp2221 device are output report. Response received from mcp2221 is input report.

Datasheet (page 45-48) contains details about how to decode the response received from device:
http://ww1.microchip.com/downloads/en/DeviceDoc/20005565B.pdf

This looks good to me.

Yours,
Linus Walleij

maintainer Applied
#2 lore raw
In reply to Rishi Gupta
Quoted 18 lines · Rishi Gupta

MCP2221 has 4 pins that can be used as GPIO or configured for alternate functionality such as clock generation and IRQ detection. This patch adds support for GPIO functionality.

To set direction of a pin or to toggle its state after it has been configured as GPIO, driver sends command to mcp2221 and parses response received from mcp2221. Based on this response either 0 or appropriate error code is returned to GPIO framework.

To get the direction or current state of a pin, driver sends command and read response from the device. Based on the response received from device direction or value is sent to the GPIO framework.

Command from driver to mcp2221 device are output report. Response received from mcp2221 is input report.

Quoted 8 lines

Datasheet (page 45-48) contains details about how to decode the response received from device:
http://ww1.microchip.com/downloads/en/DeviceDoc/20005565B.pdf

---
 drivers/hid/hid-mcp2221.c | 169 ++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 169 insertions(+)

Applied, thanks.

Signature · 2 lines
Jiri Kosina
SUSE Labs