Convert mxs/imx spi/cspi/lpspi binding to json-schema
cover Convert mxs/imx spi/cspi/lpspi binding to json-schema
This patch series converts mxs/imx spi/cspi/lpspi binding to json-schema.
In fsl-imx-cspi.yaml, also update compatible, remove obsolete properties "fsl,spi-num-chipselects" and update the example based on latest DT file;
In spi-fsl-lpspi.yaml, the original maintainer's email address [email protected] is no longer valid, so I use mine.
Anson Huang (3):
dt-bindings: spi: Convert mxs spi to json-schema
dt-bindings: spi: Convert imx cspi to json-schema
dt-bindings: spi: Convert imx lpspi to json-schema
.../devicetree/bindings/spi/fsl-imx-cspi.txt | 56 ------------- .../devicetree/bindings/spi/fsl-imx-cspi.yaml | 97 ++++++++++++++++++++++ Documentation/devicetree/bindings/spi/mxs-spi.txt | 26 ------ Documentation/devicetree/bindings/spi/mxs-spi.yaml | 55 ++++++++++++ .../devicetree/bindings/spi/spi-fsl-lpspi.txt | 29 ------- .../devicetree/bindings/spi/spi-fsl-lpspi.yaml | 60 +++++++++++++ 6 files changed, 212 insertions(+), 111 deletions(-) delete mode 100644 Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt create mode 100644 Documentation/devicetree/bindings/spi/fsl-imx-cspi.yaml delete mode 100644 Documentation/devicetree/bindings/spi/mxs-spi.txt create mode 100644 Documentation/devicetree/bindings/spi/mxs-spi.yaml delete mode 100644 Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt create mode 100644 Documentation/devicetree/bindings/spi/spi-fsl-lpspi.yaml
Signature · 1 line
2.7.4
PATCH 1/3 dt-bindings: spi: Convert mxs spi to json-schema
Convert the MXS SPI binding to DT schema format using json-schema
--- Documentation/devicetree/bindings/spi/mxs-spi.txt | 26 ---------- Documentation/devicetree/bindings/spi/mxs-spi.yaml | 55 ++++++++++++++++++++++ 2 files changed, 55 insertions(+), 26 deletions(-) delete mode 100644 Documentation/devicetree/bindings/spi/mxs-spi.txt create mode 100644 Documentation/devicetree/bindings/spi/mxs-spi.yaml
Documentation/devicetree/bindings/spi/mxs-spi.txt deleted +0 -26
@@ -1,26 +0,0 @@ -* Freescale MX233/MX28 SSP/SPI - -Required properties: -- compatible: Should be "fsl,<soc>-spi", where soc is "imx23" or "imx28" -- reg: Offset and length of the register set for the device -- interrupts: Should contain SSP ERROR interrupt -- dmas: DMA specifier, consisting of a phandle to DMA controller node - and SSP DMA channel ID. - Refer to dma.txt and fsl-mxs-dma.txt for details. -- dma-names: Must be "rx-tx". - -Optional properties: -- clock-frequency : Input clock frequency to the SPI block in Hz. - Default is 160000000 Hz. - -Example: - -ssp0: ssp@80010000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,imx28-spi"; - reg = <0x80010000 0x2000>; - interrupts = <96>; - dmas = <&dma_apbh 0>; - dma-names = "rx-tx"; -};
Documentation/devicetree/bindings/spi/mxs-spi.yaml new file +55 -0
55 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH 2/3 dt-bindings: spi: Convert imx cspi to json-schema
In reply to Anson HuangConvert the i.MX CSPI binding to DT schema format using json-schema, update compatible, remove obsolete properties "fsl,spi-num-chipselects" and update the example based on latest DT file.
--- .../devicetree/bindings/spi/fsl-imx-cspi.txt | 56 ------------- .../devicetree/bindings/spi/fsl-imx-cspi.yaml | 97 ++++++++++++++++++++++ 2 files changed, 97 insertions(+), 56 deletions(-) delete mode 100644 Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt create mode 100644 Documentation/devicetree/bindings/spi/fsl-imx-cspi.yaml
Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt deleted +0 -56
@@ -1,56 +0,0 @@ -* Freescale (Enhanced) Configurable Serial Peripheral Interface - (CSPI/eCSPI) for i.MX - -Required properties: -- compatible : - - "fsl,imx1-cspi" for SPI compatible with the one integrated on i.MX1 - - "fsl,imx21-cspi" for SPI compatible with the one integrated on i.MX21 - - "fsl,imx27-cspi" for SPI compatible with the one integrated on i.MX27 - - "fsl,imx31-cspi" for SPI compatible with the one integrated on i.MX31 - - "fsl,imx35-cspi" for SPI compatible with the one integrated on i.MX35 - - "fsl,imx51-ecspi" for SPI compatible with the one integrated on i.MX51 - - "fsl,imx53-ecspi" for SPI compatible with the one integrated on i.MX53 and later Soc - - "fsl,imx8mq-ecspi" for SPI compatible with the one integrated on i.MX8MQ - - "fsl,imx8mm-ecspi" for SPI compatible with the one integrated on i.MX8MM - - "fsl,imx8mn-ecspi" for SPI compatible with the one integrated on i.MX8MN - - "fsl,imx8mp-ecspi" for SPI compatible with the one integrated on i.MX8MP -- reg : Offset and length of the register set for the device -- interrupts : Should contain CSPI/eCSPI interrupt -- clocks : Clock specifiers for both ipg and per clocks. -- clock-names : Clock names should include both "ipg" and "per" -See the clock consumer binding, - Documentation/devicetree/bindings/clock/clock-bindings.txt - -Recommended properties: -- cs-gpios : GPIOs to use as chip selects, see spi-bus.txt. While the native chip -select lines can be used, they appear to always generate a pulse between each -word of a transfer. Most use cases will require GPIO based chip selects to -generate a valid transaction. - -Optional properties: -- num-cs : Number of total chip selects, see spi-bus.txt. -- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, -Documentation/devicetree/bindings/dma/dma.txt. -- dma-names: DMA request names, if present, should include "tx" and "rx". -- fsl,spi-rdy-drctl: Integer, representing the value of DRCTL, the register -controlling the SPI_READY handling. Note that to enable the DRCTL consideration, -the SPI_READY mode-flag needs to be set too. -Valid values are: 0 (disabled), 1 (edge-triggered burst) and 2 (level-triggered burst). - -Obsolete properties: -- fsl,spi-num-chipselects : Contains the number of the chipselect - -Example: - -ecspi@70010000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,imx51-ecspi"; - reg = <0x70010000 0x4000>; - interrupts = <36>; - cs-gpios = <&gpio3 24 0>, /* GPIO3_24 */ - <&gpio3 25 0>; /* GPIO3_25 */ - dmas = <&sdma 3 7 1>, <&sdma 4 7 2>; - dma-names = "rx", "tx"; - fsl,spi-rdy-drctl = <1>; -};
Documentation/devicetree/bindings/spi/fsl-imx-cspi.yaml new file +97 -0
97 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH 3/3 dt-bindings: spi: Convert imx lpspi to json-schema
In reply to Anson HuangConvert the i.MX LPSPI binding to DT schema format using json-schema
--- .../devicetree/bindings/spi/spi-fsl-lpspi.txt | 29 ----------- .../devicetree/bindings/spi/spi-fsl-lpspi.yaml | 60 ++++++++++++++++++++++ 2 files changed, 60 insertions(+), 29 deletions(-) delete mode 100644 Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt create mode 100644 Documentation/devicetree/bindings/spi/spi-fsl-lpspi.yaml
Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt deleted +0 -29
@@ -1,29 +0,0 @@ -* Freescale Low Power SPI (LPSPI) for i.MX - -Required properties: -- compatible : - - "fsl,imx7ulp-spi" for LPSPI compatible with the one integrated on i.MX7ULP soc - - "fsl,imx8qxp-spi" for LPSPI compatible with the one integrated on i.MX8QXP soc -- reg : address and length of the lpspi master registers -- interrupt-parent : core interrupt controller -- interrupts : lpspi interrupt -- clocks : lpspi clock specifier. Its number and order need to correspond to the - value in clock-names. -- clock-names : Corresponding to per clock and ipg clock in "clocks" - respectively. In i.MX7ULP, it only has per clk, so use CLK_DUMMY - to fill the "ipg" blank. -- spi-slave : spi slave mode support. In slave mode, add this attribute without - value. In master mode, remove it. - -Examples: - -lpspi2: lpspi@40290000 { - compatible = "fsl,imx7ulp-spi"; - reg = <0x40290000 0x10000>; - interrupt-parent = <&intc>; - interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clks IMX7ULP_CLK_LPSPI2>, - <&clks IMX7ULP_CLK_DUMMY>; - clock-names = "per", "ipg"; - spi-slave; -};
Documentation/devicetree/bindings/spi/spi-fsl-lpspi.yaml new file +60 -0
60 lines not on this page · raw message
Signature · 1 line
2.7.4