Skip to contentSkip to conversation

ASoC: rt5682: Enable Vref2 under using PLL2

PATCH Superseded [email protected] 2 participants 7 messages Jun 12, 2020 – Jun 15, 2020

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/5 ASoC: rt5682: Enable Vref2 under using PLL2

From: "derek.fang" <[email protected]>

Enable Vref2 under long term using PLL2 to avoid clock unstable.

---
 sound/soc/codecs/rt5682.c | 24 +++++++++++++++++-------
 1 file changed, 17 insertions(+), 7 deletions(-)
sound/soc/codecs/rt5682.c +17 -7
index d324512..ca8e1f2 100644
@@ -960,13 +960,12 @@ int rt5682_headset_detect(struct snd_soc_component *component, int jack_insert)
 		rt5682_enable_push_button_irq(component, false);
 		snd_soc_component_update_bits(component, RT5682_CBJ_CTRL_1,
 			RT5682_TRIG_JD_MASK, RT5682_TRIG_JD_LOW);
-		if (snd_soc_dapm_get_pin_status(dapm, "MICBIAS"))
+		if (!snd_soc_dapm_get_pin_status(dapm, "MICBIAS"))
 			snd_soc_component_update_bits(component,
-				RT5682_PWR_ANLG_1, RT5682_PWR_VREF2, 0);
-		else
+				RT5682_PWR_ANLG_1, RT5682_PWR_MB, 0);
+		if (!snd_soc_dapm_get_pin_status(dapm, "Vref2"))
 			snd_soc_component_update_bits(component,
-				RT5682_PWR_ANLG_1,
-				RT5682_PWR_VREF2 | RT5682_PWR_MB, 0);
+				RT5682_PWR_ANLG_1, RT5682_PWR_VREF2, 0);
 		snd_soc_component_update_bits(component, RT5682_PWR_ANLG_3,
 			RT5682_PWR_CBJ, 0);
 
@@ -1601,8 +1600,7 @@ static const struct snd_soc_dapm_widget rt5682_dapm_widgets[] = {
 		0, set_filter_clk, SND_SOC_DAPM_PRE_PMU),
 	SND_SOC_DAPM_SUPPLY("Vref1", RT5682_PWR_ANLG_1, RT5682_PWR_VREF1_BIT, 0,
 		rt5682_set_verf, SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMU),
-	SND_SOC_DAPM_SUPPLY("Vref2", RT5682_PWR_ANLG_1, RT5682_PWR_VREF2_BIT, 0,
-		NULL, 0),
+	SND_SOC_DAPM_SUPPLY("Vref2", SND_SOC_NOPM, 0, 0, NULL, 0),
 	SND_SOC_DAPM_SUPPLY("MICBIAS", SND_SOC_NOPM, 0, 0, NULL, 0),
 
 	/* ASRC */
@@ -2485,6 +2483,15 @@ static int rt5682_wclk_prepare(struct clk_hw *hw)
 	snd_soc_dapm_force_enable_pin_unlocked(dapm, "MICBIAS");
 	snd_soc_component_update_bits(component, RT5682_PWR_ANLG_1,
 				RT5682_PWR_MB, RT5682_PWR_MB);
+
+	snd_soc_dapm_force_enable_pin_unlocked(dapm, "Vref2");
+	snd_soc_component_update_bits(component, RT5682_PWR_ANLG_1,
+			RT5682_PWR_VREF2 | RT5682_PWR_FV2,
+			RT5682_PWR_VREF2);
+	usleep_range(55000, 60000);
+	snd_soc_component_update_bits(component, RT5682_PWR_ANLG_1,
+			RT5682_PWR_FV2, RT5682_PWR_FV2);
+
 	snd_soc_dapm_force_enable_pin_unlocked(dapm, "I2S1");
 	snd_soc_dapm_force_enable_pin_unlocked(dapm, "PLL2F");
 	snd_soc_dapm_force_enable_pin_unlocked(dapm, "PLL2B");
@@ -2510,9 +2517,12 @@ static void rt5682_wclk_unprepare(struct clk_hw *hw)
 	snd_soc_dapm_mutex_lock(dapm);
 
 	snd_soc_dapm_disable_pin_unlocked(dapm, "MICBIAS");
+	snd_soc_dapm_disable_pin_unlocked(dapm, "Vref2");
 	if (!rt5682->jack_type)
 		snd_soc_component_update_bits(component, RT5682_PWR_ANLG_1,
+				RT5682_PWR_VREF2 | RT5682_PWR_FV2 |
 				RT5682_PWR_MB, 0);
+
 	snd_soc_dapm_disable_pin_unlocked(dapm, "I2S1");
 	snd_soc_dapm_disable_pin_unlocked(dapm, "PLL2F");
 	snd_soc_dapm_disable_pin_unlocked(dapm, "PLL2B");
Signature · 1 line
2.7.4
#1 lore raw

PATCH 2/5 ASoC: rl6231: Add new supports on rl6231

From: "derek.fang" <[email protected]>

Add pll preset maps for Realtek codecs' PLL2 freq conversions.

---
 sound/soc/codecs/rl6231.c | 2 ++
 1 file changed, 2 insertions(+)
sound/soc/codecs/rl6231.c +2 -0
index 8c9daf3..d1fc170 100644
@@ -103,7 +103,9 @@ struct pll_calc_map {
 static const struct pll_calc_map pll_preset_table[] = {
 	{19200000,  4096000,  23, 14, 1, false, false},
 	{19200000,  24576000,  3, 30, 3, false, false},
+	{48000000,  3840000,  23,  2, 0, false, false},
 	{3840000,   24576000,  3, 30, 0, true, false},
+	{3840000,   22579200,  3,  5, 0, true, false},
 };
 
 static unsigned int find_best_div(unsigned int in,
Signature · 1 line
2.7.4
#2 lore raw

PATCH 3/5 ASoC: rt5682: Let PLL2 support the freq conversion for 44100Hz sample rate

In reply to [email protected]

From: "derek.fang" <[email protected]>

PLL2 of rt5682 only supports the freq conversion for 48000Hz sample rate so far, this patch lets it support 44100Hz.

---
 sound/soc/codecs/rt5682.c | 9 ++++++++-
 sound/soc/codecs/rt5682.h | 4 ++++
 2 files changed, 12 insertions(+), 1 deletion(-)
sound/soc/codecs/rt5682.c +8 -1
index ca8e1f2..5959b6a 100644
@@ -2246,7 +2246,7 @@ static int rt5682_set_component_pll(struct snd_soc_component *component,
 {
 	struct rt5682_priv *rt5682 = snd_soc_component_get_drvdata(component);
 	struct rl6231_pll_code pll_code, pll2f_code, pll2b_code;
-	unsigned int pll2_fout1;
+	unsigned int pll2_fout1, pll2_ps_val;
 	int ret;
 
 	if (source == rt5682->pll_src[pll_id] &&
@@ -2315,8 +2315,15 @@ static int rt5682_set_component_pll(struct snd_soc_component *component,
 			pll2b_code.n_code);
 		snd_soc_component_write(component, RT5682_PLL2_CTRL_3,
 			pll2f_code.n_code << RT5682_PLL2F_N_SFT);
+
+		if (freq_out == 22579200)
+			pll2_ps_val = 1 << RT5682_PLL2B_SEL_PS_SFT;
+		else
+			pll2_ps_val = 1 << RT5682_PLL2B_PS_BYP_SFT;
 		snd_soc_component_update_bits(component, RT5682_PLL2_CTRL_4,
+			RT5682_PLL2B_SEL_PS_MASK | RT5682_PLL2B_PS_BYP_MASK |
 			RT5682_PLL2B_M_BP_MASK | RT5682_PLL2F_M_BP_MASK | 0xf,
+			pll2_ps_val |
 			(pll2b_code.m_bp ? 1 : 0) << RT5682_PLL2B_M_BP_SFT |
 			(pll2f_code.m_bp ? 1 : 0) << RT5682_PLL2F_M_BP_SFT |
 			0xf);
sound/soc/codecs/rt5682.h +4 -0
index f172c9e..6d94327 100644
@@ -1080,6 +1080,10 @@
 #define RT5682_PLL2F_N_SFT			8
 
 /* PLL2 M/N/K Code Control 2 (0x009e) */
+#define RT5682_PLL2B_SEL_PS_MASK		(0x1 << 13)
+#define RT5682_PLL2B_SEL_PS_SFT			13
+#define RT5682_PLL2B_PS_BYP_MASK		(0x1 << 12)
+#define RT5682_PLL2B_PS_BYP_SFT			12
 #define RT5682_PLL2B_M_BP_MASK			(0x1 << 11)
 #define RT5682_PLL2B_M_BP_SFT			11
 #define RT5682_PLL2F_M_BP_MASK			(0x1 << 7)
Signature · 1 line
2.7.4
#3 lore raw

PATCH 4/5 ASoC: rt5682: DAI wclk supports 44100 Hz output

In reply to [email protected]

From: "derek.fang" <[email protected]>

DAI Wclk of rt5682 only supports 48000Hz output so far, this patch lets it support 44100Hz.

---
 sound/soc/codecs/rt5682.c | 49 ++++++++++++++++++++++++++++++-----------------
 1 file changed, 31 insertions(+), 18 deletions(-)
sound/soc/codecs/rt5682.c +31 -18
index 5959b6a..f9d8d8c 100644
@@ -2461,8 +2461,8 @@ static int rt5682_set_bias_level(struct snd_soc_component *component,
 
 #ifdef CONFIG_COMMON_CLK
 #define CLK_PLL2_FIN 48000000
-#define CLK_PLL2_FOUT 24576000
 #define CLK_48 48000
+#define CLK_44 44100
 
 static bool rt5682_clk_check(struct rt5682_priv *rt5682)
 {
@@ -2544,13 +2544,22 @@ static unsigned long rt5682_wclk_recalc_rate(struct clk_hw *hw,
 	struct rt5682_priv *rt5682 =
 		container_of(hw, struct rt5682_priv,
 			     dai_clks_hw[RT5682_DAI_WCLK_IDX]);
+	struct snd_soc_component *component = rt5682->component;
+	const char * const clk_name = __clk_get_name(hw->clk);
 
 	if (!rt5682_clk_check(rt5682))
 		return 0;
 	/*
-	 * Only accept to set wclk rate to 48kHz temporarily.
+	 * Only accept to set wclk rate to 44.1k or 48kHz.
 	 */
-	return CLK_48;
+	if (rt5682->lrck[RT5682_AIF1] != CLK_48 &&
+	    rt5682->lrck[RT5682_AIF1] != CLK_44) {
+		dev_warn(component->dev, "%s: clk %s only support %d or %d Hz output\n",
+			__func__, clk_name, CLK_44, CLK_48);
+		return 0;
+	}
+
+	return rt5682->lrck[RT5682_AIF1];
 }
 
 static long rt5682_wclk_round_rate(struct clk_hw *hw, unsigned long rate,
@@ -2559,13 +2568,22 @@ static long rt5682_wclk_round_rate(struct clk_hw *hw, unsigned long rate,
 	struct rt5682_priv *rt5682 =
 		container_of(hw, struct rt5682_priv,
 			     dai_clks_hw[RT5682_DAI_WCLK_IDX]);
+	struct snd_soc_component *component = rt5682->component;
+	const char * const clk_name = __clk_get_name(hw->clk);
 
 	if (!rt5682_clk_check(rt5682))
 		return -EINVAL;
 	/*
-	 * Only accept to set wclk rate to 48kHz temporarily.
+	 * Only accept to set wclk rate to 44.1k or 48kHz.
+	 * It will force to 48kHz if not both.
 	 */
-	return CLK_48;
+	if (rate != CLK_48 && rate != CLK_44) {
+		dev_warn(component->dev, "%s: clk %s only support %d or %d Hz output\n",
+			__func__, clk_name, CLK_44, CLK_48);
+		rate = CLK_48;
+	}
+
+	return rate;
 }
 
 static int rt5682_wclk_set_rate(struct clk_hw *hw, unsigned long rate,
@@ -2578,6 +2596,7 @@ static int rt5682_wclk_set_rate(struct clk_hw *hw, unsigned long rate,
 	struct clk *parent_clk;
 	const char * const clk_name = __clk_get_name(hw->clk);
 	int pre_div;
+	unsigned int clk_pll2_out;
 
 	if (!rt5682_clk_check(rt5682))
 		return -EINVAL;
@@ -2600,23 +2619,17 @@ static int rt5682_wclk_set_rate(struct clk_hw *hw, unsigned long rate,
 			clk_name, CLK_PLL2_FIN);
 
 	/*
-	 * It's a temporary limitation. Only accept to set wclk rate to 48kHz.
-	 * It will force wclk to 48kHz even it's not.
-	 */
-	if (rate != CLK_48) {
-		dev_warn(component->dev, "clk %s only support %d Hz output\n",
-			clk_name, CLK_48);
-		rate = CLK_48;
-	}
-
-	/*
-	 * To achieve the rate conversion from 48MHz to 48kHz, PLL2 is needed.
+	 * To achieve the rate conversion from 48MHz to 44.1k or 48kHz,
+	 * PLL2 is needed.
 	 */
+	clk_pll2_out = rate * 512;
 	rt5682_set_component_pll(component, RT5682_PLL2, RT5682_PLL2_S_MCLK,
-		CLK_PLL2_FIN, CLK_PLL2_FOUT);
+		CLK_PLL2_FIN, clk_pll2_out);
 
 	rt5682_set_component_sysclk(component, RT5682_SCLK_S_PLL2, 0,
-		CLK_PLL2_FOUT, SND_SOC_CLOCK_IN);
+		clk_pll2_out, SND_SOC_CLOCK_IN);
+
+	rt5682->lrck[RT5682_AIF1] = rate;
 
 	pre_div = rl6231_get_clk_info(rt5682->sysclk, rate);
 
Signature · 1 line
2.7.4
#4 lore raw

PATCH 5/5 ASoC: rt5682: Let dai clks be registered whether mclk exists or not

In reply to [email protected]

From: "derek.fang" <[email protected]>

According to ideal rt5682 CCF, the root clk is mclk.
But in some platforms, mclk is not exported to CCF.
In this condition, rt5682_register_dai_clks will not be called. This patch lets dai clks could be registered whether mclk exists or not.

---
 sound/soc/codecs/rt5682.c | 11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)
sound/soc/codecs/rt5682.c +6 -5
index f9d8d8c..ff6a5bb 100644
@@ -2859,12 +2859,13 @@ static int rt5682_probe(struct snd_soc_component *component)
 				return ret;
 			}
 			rt5682->mclk = NULL;
-		} else {
-			/* Register CCF DAI clock control */
-			ret = rt5682_register_dai_clks(component);
-			if (ret)
-				return ret;
 		}
+
+		/* Register CCF DAI clock control */
+		ret = rt5682_register_dai_clks(component);
+		if (ret)
+			return ret;
+
 		/* Initial setup for CCF */
 		rt5682->lrck[RT5682_AIF1] = CLK_48;
 #endif
Signature · 1 line
2.7.4
maintainer
#5 lore raw
In reply to [email protected]
Quoted 1 line · On Fri, 12 Jun 2020 13:15:21 +0800, [email protected] wrote:

Enable Vref2 under long term using PLL2 to avoid clock unstable.

Applied to

https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next

Thanks!

[1/5] ASoC: rt5682: Enable Vref2 under using PLL2
(no commit info)
[2/5] ASoC: rl6231: Add new supports on rl6231
(no commit info)
[3/5] ASoC: rt5682: Let PLL2 support the freq conversion for 44100Hz sample rate
(no commit info)
[4/5] ASoC: rt5682: DAI wclk supports 44100 Hz output
(no commit info)
[5/5] ASoC: rt5682: Let dai clks be registered whether mclk exists or not

      commit: 19ab0f005b165146ea4a93f71e9cb5e71de9c0ce

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

Thanks,
Mark

maintainer
#6 lore raw
In reply to [email protected]
Quoted 1 line · On Fri, 12 Jun 2020 13:15:21 +0800, [email protected] wrote:

Enable Vref2 under long term using PLL2 to avoid clock unstable.

Applied to

https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next

Thanks!

[1/5] ASoC: rt5682: Enable Vref2 under using PLL2
(no commit info)
[2/5] ASoC: rl6231: Add new supports on rl6231

      commit: 8d8efecb28b8f622330ea3546cbdcc06e667f6b5
[3/5] ASoC: rt5682: Let PLL2 support the freq conversion for 44100Hz sample rate
      commit: d54348fbefcd006b2bf1db5c01159f2101b94a3f
[4/5] ASoC: rt5682: DAI wclk supports 44100 Hz output
      commit: fde418b61d815684a37d58106d2345bfd7805f13
[5/5] ASoC: rt5682: Let dai clks be registered whether mclk exists or not
      commit: 19ab0f005b165146ea4a93f71e9cb5e71de9c0ce

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

Thanks,
Mark