Skip to contentSkip to conversation

doc: qemu-riscv: Update QEMU run command

PATCH New Bin Meng 2 participants 2 messages Jun 23, 2020 RISC-V

lore
Share & tools
lore

Bin Meng

author
#0 lore raw

PATCH 1/1 doc: qemu-riscv: Update QEMU run command

From: Bin Meng <[email protected]>

Explicitly pass the "-bios" option to QEMU to run U-Boot, instead of the "-kernel" option, as we know that "-bios" behavior will be changed since QEMU 5.1.0.

This also updates validated QEMU version to 5.0.0.

---

 doc/board/emulation/qemu-riscv.rst | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
doc/board/emulation/qemu-riscv.rst +5 -5
index c390006..b68db95 100644
@@ -40,11 +40,11 @@ The minimal QEMU command line to get U-Boot up and running is:
 
 - For 32-bit RISC-V::
 
-    qemu-system-riscv32 -nographic -machine virt -kernel u-boot
+    qemu-system-riscv32 -nographic -machine virt -bios u-boot
 
 - For 64-bit RISC-V::
 
-    qemu-system-riscv64 -nographic -machine virt -kernel u-boot
+    qemu-system-riscv64 -nographic -machine virt -bios u-boot
 
 The commands above create targets with 128MiB memory by default.
 A freely configurable amount of RAM can be created via the '-m'
@@ -56,7 +56,7 @@ For instructions on how to run U-Boot in supervisor mode on QEMU
 with OpenSBI, see the documentation available with OpenSBI:
 https://github.com/riscv/opensbi/blob/master/docs/platform/qemu_virt.md
 
-These have been tested in QEMU 4.2.0.
+These have been tested in QEMU 5.0.0.
 
 Running U-Boot SPL
 ------------------
@@ -98,10 +98,10 @@ configurations are:
 
 - For 32-bit RISC-V::
 
-    qemu-system-riscv32 -nographic -machine virt -kernel spl/u-boot-spl \
+    qemu-system-riscv32 -nographic -machine virt -bios spl/u-boot-spl \
     -device loader,file=u-boot.itb,addr=0x80200000
 
 - For 64-bit RISC-V::
 
-    qemu-system-riscv64 -nographic -machine virt -kernel spl/u-boot-spl \
+    qemu-system-riscv64 -nographic -machine virt -bios spl/u-boot-spl \
     -device loader,file=u-boot.itb,addr=0x80200000
Signature · 1 line
2.7.4
#1 lore raw

PATCH 1/1 doc: qemu-riscv: Update QEMU run command

Quoted 56 lines · Bin Meng

From: Bin Meng <[email protected]>

Explicitly pass the "-bios" option to QEMU to run U-Boot, instead of the "-kernel" option, as we know that "-bios" behavior will be changed since QEMU 5.1.0.

This also updates validated QEMU version to 5.0.0.

---

 doc/board/emulation/qemu-riscv.rst | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
doc/board/emulation/qemu-riscv.rst +5 -6
index c390006..b68db95 100644
@@ -40,11 +40,11 @@ The minimal QEMU command line to get U-Boot up and running is:
 
 - For 32-bit RISC-V::
 
-    qemu-system-riscv32 -nographic -machine virt -kernel u-boot
+    qemu-system-riscv32 -nographic -machine virt -bios u-boot
 
 - For 64-bit RISC-V::
 
-    qemu-system-riscv64 -nographic -machine virt -kernel u-boot
+    qemu-system-riscv64 -nographic -machine virt -bios u-boot
 
 The commands above create targets with 128MiB memory by default.
 A freely configurable amount of RAM can be created via the '-m'
@@ -56,7 +56,7 @@ For instructions on how to run U-Boot in supervisor mode on QEMU
 with OpenSBI, see the documentation available with OpenSBI:
 https://github.com/riscv/opensbi/blob/master/docs/platform/qemu_virt.md
 
-These have been tested in QEMU 4.2.0.
+These have been tested in QEMU 5.0.0.
 
 Running U-Boot SPL
 ------------------
@@ -98,10 +98,10 @@ configurations are:
 
 - For 32-bit RISC-V::
 
-    qemu-system-riscv32 -nographic -machine virt -kernel spl/u-boot-spl \
+    qemu-system-riscv32 -nographic -machine virt -bios spl/u-boot-spl \
     -device loader,file=u-boot.itb,addr=0x80200000
 
 - For 64-bit RISC-V::
 
-    qemu-system-riscv64 -nographic -machine virt -kernel spl/u-boot-spl \
+    qemu-system-riscv64 -nographic -machine virt -bios spl/u-boot-spl \
     -device loader,file=u-boot.itb,addr=0x80200000
--
Quoted 2 lines

2.7.4

Signature · 2 lines
Regards,
Atish