Skip to contentSkip to conversation

sdm845/sc7180: Add OPP tables to support IO DVFS

PATCH In review Rajendra Nayak 2 participants 9 messages Jun 30, 2020

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

cover sdm845/sc7180: Add OPP tables to support IO DVFS

Driver changes to support DVFS for sdhc and qup (uart and spi) have been merged. Add OPP tables and power-domains in device tree to enable support for DVFS in these devices, on sdm845 and sc7180 SoC platforms.

These were posted earlier and reviewed [1] and later dropped by me to first get the driver changes merged in.
The last outstanding comment on these was from Matthias to move the OPP tables inside of the node which uses them. I have done that for sdhc, but left the qup tables outside as its a common table used across many nodes, and it just gets more confusing adding it elsewhere.

Patches are rebased and should apply cleanly on for-next of the msm tree.

[1] https://lkml.org/lkml/2020/4/28/561

Rajendra Nayak (4):
arm64: dts: sdm845: Add OPP table for all qup devices
arm64: dts: sc7180: Add OPP table for all qup devices
arm64: dts: sdm845: Add sdhc opps and power-domains
arm64: dts: sc7180: Add sdhc opps and power-domains

 arch/arm64/boot/dts/qcom/sc7180.dtsi |  91 +++++++++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/sdm845.dtsi | 109 +++++++++++++++++++++++++++++++++++
 2 files changed, 200 insertions(+)
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#1 lore raw

PATCH 1/4 arm64: dts: sdm845: Add OPP table for all qup devices

qup has a requirement to vote on the performance state of the CX domain in sdm845 devices. Add OPP tables for these and also add power-domains property for all qup instances for uart and spi.
i2c does not support scaling and uses a fixed clock.

---
 arch/arm64/boot/dts/qcom/sdm845.dtsi | 83 ++++++++++++++++++++++++++++++++++++
 1 file changed, 83 insertions(+)
arch/arm64/boot/dts/qcom/sdm845.dtsi +83 -0
index 8eb5a31..db1f82b 100644
@@ -805,6 +805,25 @@
 			clock-names = "core";
 		};
 
+		qup_opp_table: qup-opp-table {
+			compatible = "operating-points-v2";
+
+			opp-19200000 {
+				opp-hz = /bits/ 64 <19200000>;
+				required-opps = <&rpmhpd_opp_min_svs>;
+			};
+
+			opp-75000000 {
+				opp-hz = /bits/ 64 <75000000>;
+				required-opps = <&rpmhpd_opp_low_svs>;
+			};
+
+			opp-100000000 {
+				opp-hz = /bits/ 64 <100000000>;
+				required-opps = <&rpmhpd_opp_svs>;
+			};
+		};
+
 		qupv3_id_0: geniqup@8c0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0 0x008c0000 0 0x6000>;
@@ -839,6 +858,8 @@
 				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -850,6 +871,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart0_default>;
 				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -876,6 +899,8 @@
 				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -887,6 +912,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart1_default>;
 				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -913,6 +940,8 @@
 				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -924,6 +953,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart2_default>;
 				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -950,6 +981,8 @@
 				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -961,6 +994,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart3_default>;
 				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -987,6 +1022,8 @@
 				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -998,6 +1035,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart4_default>;
 				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1024,6 +1063,8 @@
 				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1035,6 +1076,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart5_default>;
 				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1061,6 +1104,8 @@
 				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1072,6 +1117,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart6_default>;
 				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1098,6 +1145,8 @@
 				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1109,6 +1158,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart7_default>;
 				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 		};
@@ -1147,6 +1198,8 @@
 				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1158,6 +1211,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart8_default>;
 				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1184,6 +1239,8 @@
 				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1195,6 +1252,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart9_default>;
 				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1221,6 +1280,8 @@
 				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1232,6 +1293,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart10_default>;
 				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1258,6 +1321,8 @@
 				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1269,6 +1334,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart11_default>;
 				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1295,6 +1362,8 @@
 				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1306,6 +1375,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart12_default>;
 				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1332,6 +1403,8 @@
 				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1343,6 +1416,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart13_default>;
 				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1369,6 +1444,8 @@
 				interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1380,6 +1457,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart14_default>;
 				interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1406,6 +1485,8 @@
 				interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 
@@ -1417,6 +1498,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart15_default>;
 				interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SDM845_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				status = "disabled";
 			};
 		};
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
Reviewed-by on v1 1/4
#2 lore raw

Re: [PATCH 1/4] arm64: dts: sdm845: Add OPP table for all qup devices

Quoted 7 lines · Rajendra Nayak

qup has a requirement to vote on the performance state of the CX domain in sdm845 devices. Add OPP tables for these and also add power-domains property for all qup instances for uart and spi.
i2c does not support scaling and uses a fixed clock.

#3 lore raw

PATCH 2/4 arm64: dts: sc7180: Add OPP table for all qup devices

In reply to Rajendra Nayak

qup has a requirement to vote on the performance state of the CX domain in sc7180 devices. Add OPP tables for these and also add power-domains property for all qup instances for uart and spi.
i2c does not support scaling and uses a fixed clock.

---
 arch/arm64/boot/dts/qcom/sc7180.dtsi | 59 ++++++++++++++++++++++++++++++++++++
 1 file changed, 59 insertions(+)
arch/arm64/boot/dts/qcom/sc7180.dtsi +59 -0
index ad57df2..78fef54 100644
@@ -537,6 +537,25 @@
 			status = "disabled";
 		};
 
+		qup_opp_table: qup-opp-table {
+			compatible = "operating-points-v2";
+
+			opp-75000000 {
+				opp-hz = /bits/ 64 <75000000>;
+				required-opps = <&rpmhpd_opp_low_svs>;
+			};
+
+			opp-100000000 {
+				opp-hz = /bits/ 64 <100000000>;
+				required-opps = <&rpmhpd_opp_svs>;
+			};
+
+			opp-128000000 {
+				opp-hz = /bits/ 64 <128000000>;
+				required-opps = <&rpmhpd_opp_nom>;
+			};
+		};
+
 		qupv3_id_0: geniqup@8c0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0 0x008c0000 0 0x6000>;
@@ -579,6 +598,8 @@
 				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_0>;
 				interconnect-names = "qup-core", "qup-config";
@@ -593,6 +614,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart0_default>;
 				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_0>;
 				interconnect-names = "qup-core", "qup-config";
@@ -627,6 +650,8 @@
 				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_0>;
 				interconnect-names = "qup-core", "qup-config";
@@ -641,6 +666,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart1_default>;
 				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_0>;
 				interconnect-names = "qup-core", "qup-config";
@@ -673,6 +700,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart2_default>;
 				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_0>;
 				interconnect-names = "qup-core", "qup-config";
@@ -707,6 +736,8 @@
 				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_0>;
 				interconnect-names = "qup-core", "qup-config";
@@ -721,6 +752,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart3_default>;
 				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_0>;
 				interconnect-names = "qup-core", "qup-config";
@@ -753,6 +786,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart4_default>;
 				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_0>;
 				interconnect-names = "qup-core", "qup-config";
@@ -787,6 +822,8 @@
 				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_0>;
 				interconnect-names = "qup-core", "qup-config";
@@ -801,6 +838,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart5_default>;
 				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_0>;
 				interconnect-names = "qup-core", "qup-config";
@@ -850,6 +889,8 @@
 				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_1>;
 				interconnect-names = "qup-core", "qup-config";
@@ -864,6 +905,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart6_default>;
 				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_1>;
 				interconnect-names = "qup-core", "qup-config";
@@ -896,6 +939,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart7_default>;
 				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_1>;
 				interconnect-names = "qup-core", "qup-config";
@@ -930,6 +975,8 @@
 				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_1>;
 				interconnect-names = "qup-core", "qup-config";
@@ -944,6 +991,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart8_default>;
 				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_1>;
 				interconnect-names = "qup-core", "qup-config";
@@ -976,6 +1025,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart9_default>;
 				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_1>;
 				interconnect-names = "qup-core", "qup-config";
@@ -1010,6 +1061,8 @@
 				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_1>;
 				interconnect-names = "qup-core", "qup-config";
@@ -1024,6 +1077,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart10_default>;
 				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_1>;
 				interconnect-names = "qup-core", "qup-config";
@@ -1058,6 +1113,8 @@
 				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_1>;
 				interconnect-names = "qup-core", "qup-config";
@@ -1072,6 +1129,8 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart11_default>;
 				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7180_CX>;
+				operating-points-v2 = <&qup_opp_table>;
 				interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
 						<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_QUP_1>;
 				interconnect-names = "qup-core", "qup-config";
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
Reviewed-by on v1 2/4
#4 lore raw

Re: [PATCH 2/4] arm64: dts: sc7180: Add OPP table for all qup devices

Quoted 6 lines · Rajendra Nayak

qup has a requirement to vote on the performance state of the CX domain in sc7180 devices. Add OPP tables for these and also add power-domains property for all qup instances for uart and spi.
i2c does not support scaling and uses a fixed clock.

#5 lore raw

PATCH 3/4 arm64: dts: sdm845: Add sdhc opps and power-domains

In reply to Rajendra Nayak

Add the power domain supporting performance state and the corresponding OPP tables for the sdhc device on sdm845.

---
 arch/arm64/boot/dts/qcom/sdm845.dtsi | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)
arch/arm64/boot/dts/qcom/sdm845.dtsi +26 -0
index db1f82b..67fc87b 100644
@@ -2994,8 +2994,34 @@
 				 <&gcc GCC_SDCC2_APPS_CLK>;
 			clock-names = "iface", "core";
 			iommus = <&apps_smmu 0xa0 0xf>;
+			power-domains = <&rpmhpd SDM845_CX>;
+			operating-points-v2 = <&sdhc2_opp_table>;
 
 			status = "disabled";
+
+			sdhc2_opp_table: sdhc2-opp-table {
+				compatible = "operating-points-v2";
+
+				opp-9600000 {
+					opp-hz = /bits/ 64 <9600000>;
+					required-opps = <&rpmhpd_opp_min_svs>;
+				};
+
+				opp-19200000 {
+					opp-hz = /bits/ 64 <19200000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+				};
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <100000000>;
+					required-opps = <&rpmhpd_opp_svs>;
+				};
+
+				opp-201500000 {
+					opp-hz = /bits/ 64 <201500000>;
+					required-opps = <&rpmhpd_opp_svs_l1>;
+				};
+			};
 		};
 
 		qspi: spi@88df000 {
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#7 lore raw

PATCH 4/4 arm64: dts: sc7180: Add sdhc opps and power-domains

In reply to Rajendra Nayak

Add the power domain supporting performance state and the corresponding OPP tables for the sdhc device on sc7180.

---
 arch/arm64/boot/dts/qcom/sc7180.dtsi | 32 ++++++++++++++++++++++++++++++++
 1 file changed, 32 insertions(+)
arch/arm64/boot/dts/qcom/sc7180.dtsi +32 -0
index 78fef54..08ee49a 100644
@@ -524,6 +524,8 @@
 			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
 					<&gcc GCC_SDCC1_AHB_CLK>;
 			clock-names = "core", "iface";
+			power-domains = <&rpmhpd SC7180_CX>;
+			operating-points-v2 = <&sdhc1_opp_table>;
 
 			bus-width = <8>;
 			non-removable;
@@ -535,6 +537,20 @@
 			mmc-hs400-enhanced-strobe;
 
 			status = "disabled";
+
+			sdhc1_opp_table: sdhc1-opp-table {
+				compatible = "operating-points-v2";
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <100000000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+				};
+
+				opp-384000000 {
+					opp-hz = /bits/ 64 <384000000>;
+					required-opps = <&rpmhpd_opp_svs_l1>;
+				};
+			};
 		};
 
 		qup_opp_table: qup-opp-table {
@@ -2300,10 +2316,26 @@
 			clocks = <&gcc GCC_SDCC2_APPS_CLK>,
 					<&gcc GCC_SDCC2_AHB_CLK>;
 			clock-names = "core", "iface";
+			power-domains = <&rpmhpd SC7180_CX>;
+			operating-points-v2 = <&sdhc2_opp_table>;
 
 			bus-width = <4>;
 
 			status = "disabled";
+
+			sdhc2_opp_table: sdhc2-opp-table {
+				compatible = "operating-points-v2";
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <100000000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+				};
+
+				opp-202000000 {
+					opp-hz = /bits/ 64 <202000000>;
+					required-opps = <&rpmhpd_opp_svs_l1>;
+				};
+			};
 		};
 
 		qspi: spi@88dc000 {
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation