Skip to contentSkip to conversation

ADD interconnect support for Qualcomm DWC3 driver

PATCH Superseded Sandeep Maheswaram 2 participants 6 messages Jul 23, 2020 – Jul 27, 2020

Subsystems (6)

v10 of 11 Superseded Latest is v11 →

lore
Share & tools
lore
#0 lore raw

v10 cover ADD interconnect support for Qualcomm DWC3 driver

This path series aims to add interconnect support in dwc3-qcom driver on SDM845 and SC7180 SoCs.

Changes from v9 -> v10

Quoted 2 lines

Removed cooments for enable,disable functions. Handled the enable,disable failure cases as in v8.

Changes from v8 -> v9

Quoted 1 line

Addressed comments from Matthias.

Changes from v7 -> v8

Quoted 1 line

Only driver change is pending all other patches are merged so dropped

from the series.

Quoted 1 line

Removed the device_is_bound call and getting speed from device tree

and rearranged interconnect functions to avoid forward declarations.

Quoted 1 line

Added patch to specify maximum speed for dwc3 DT node.

Changes from v6 -> v7

Quoted 2 lines

[PATCH 2/4] Fixed review comments from Matthias in DWC3 driver. Other patches remain unchanged.

Changes from v5 -> v6

Quoted 4 lines

[PATCH 1/4] Addressed comments from Rob.
[PATCH 2/4] Fixed review comments from Matthias in DWC3 driver. [PATCH 3/4] Ignoring 80 char limit in defining interconnect paths. Added [PATCH 4/4] in this series. Adding interconnect nodes for SC7180.

    Depends on patch https://patchwork.kernel.org/patch/11417989/.	

Changes from v4 -> v5

Quoted 1 line

[PATCH 1/3] Added the interconnect properties in yaml. This patch depends

    on series https://patchwork.kernel.org/cover/11372641/.
Quoted 2 lines

[PATCH 2/3] Fixed review comments from Matthias in DWC3 driver. [PATCH 3/3] Modified as per the new interconnect nodes in sdm845. Depends

    on series https://patchwork.kernel.org/cover/11372211/. 

Changes from v3 -> v4

Quoted 2 lines

Fixed review comments from Matthias
[PATCH 1/3] and [PATCH 3/3] remains unchanged

Changes from v2 -> v3

Quoted 2 lines

Fixed review comments from Matthias and Manu changed the functions prefix from usb_* to dwc3_qcom_*

Changes since V1:

Quoted 2 lines

Comments by Georgi Djakov on "[PATCH 2/3]" addressed [PATCH 1/3] and [PATCH 3/3] remains unchanged

Sandeep Maheswaram (2):
usb: dwc3: qcom: Add interconnect support in dwc3 driver
arm64: dts: qcom: sc7180: Add maximum speed property for DWC3 USB node

 arch/arm64/boot/dts/qcom/sc7180.dtsi |   1 +
 drivers/usb/dwc3/dwc3-qcom.c         | 127 ++++++++++++++++++++++++++++++++++-
 2 files changed, 126 insertions(+), 2 deletions(-)
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#1 lore raw

PATCH v10 1/2 usb: dwc3: qcom: Add interconnect support in dwc3 driver

Add interconnect support in dwc3-qcom driver to vote for bus bandwidth.

This requires for two different paths - from USB to DDR. The other is from APPS to USB.

---
 drivers/usb/dwc3/dwc3-qcom.c | 127 ++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 125 insertions(+), 2 deletions(-)
drivers/usb/dwc3/dwc3-qcom.c +125 -2
index e1e78e9..712efb7 100644
@@ -13,6 +13,7 @@
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/extcon.h>
+#include <linux/interconnect.h>
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
 #include <linux/phy/phy.h>
@@ -43,6 +44,14 @@
 #define SDM845_QSCRATCH_SIZE			0x400
 #define SDM845_DWC3_CORE_SIZE			0xcd00
 
+/* Interconnect path bandwidths in MBps */
+#define USB_MEMORY_AVG_HS_BW MBps_to_icc(240)
+#define USB_MEMORY_PEAK_HS_BW MBps_to_icc(700)
+#define USB_MEMORY_AVG_SS_BW  MBps_to_icc(1000)
+#define USB_MEMORY_PEAK_SS_BW MBps_to_icc(2500)
+#define APPS_USB_AVG_BW 0
+#define APPS_USB_PEAK_BW MBps_to_icc(40)
+
 struct dwc3_acpi_pdata {
 	u32			qscratch_base_offset;
 	u32			qscratch_base_size;
@@ -76,6 +85,8 @@ struct dwc3_qcom {
 	enum usb_dr_mode	mode;
 	bool			is_suspended;
 	bool			pm_suspended;
+	struct icc_path		*icc_path_ddr;
+	struct icc_path		*icc_path_apps;
 };
 
 static inline void dwc3_qcom_setbits(void __iomem *base, u32 offset, u32 val)
@@ -190,6 +201,103 @@ static int dwc3_qcom_register_extcon(struct dwc3_qcom *qcom)
 	return 0;
 }
 
+static int dwc3_qcom_interconnect_enable(struct dwc3_qcom *qcom)
+{
+	int ret;
+
+	ret = icc_enable(qcom->icc_path_ddr);
+	if (ret)
+		return ret;
+
+	ret = icc_enable(qcom->icc_path_apps);
+	if (ret)
+		return icc_disable(qcom->icc_path_ddr);
+
+	return ret;
+}
+
+static int dwc3_qcom_interconnect_disable(struct dwc3_qcom *qcom)
+{
+	int ret;
+
+	ret = icc_disable(qcom->icc_path_ddr);
+	if (ret)
+		return ret;
+
+	ret = icc_disable(qcom->icc_path_apps);
+	if (ret)
+		goto err_reenable_memory_path;
+
+	return 0;
+
+	/* Re-enable things in the event of an error */
+err_reenable_memory_path:
+	dwc3_qcom_interconnect_enable(qcom);
+
+	return ret;
+}
+
+/**
+ * dwc3_qcom_interconnect_init() - Get interconnect path handles
+ * and set bandwidhth.
+ * @qcom:			Pointer to the concerned usb core.
+ *
+ */
+static int dwc3_qcom_interconnect_init(struct dwc3_qcom *qcom)
+{
+	struct device *dev = qcom->dev;
+	int ret;
+
+	qcom->icc_path_ddr = of_icc_get(dev, "usb-ddr");
+	if (IS_ERR(qcom->icc_path_ddr)) {
+		dev_err(dev, "failed to get usb-ddr path: %ld\n",
+			PTR_ERR(qcom->icc_path_ddr));
+		return PTR_ERR(qcom->icc_path_ddr);
+	}
+
+	qcom->icc_path_apps = of_icc_get(dev, "apps-usb");
+	if (IS_ERR(qcom->icc_path_apps)) {
+		dev_err(dev, "failed to get apps-usb path: %ld\n",
+				PTR_ERR(qcom->icc_path_apps));
+		return PTR_ERR(qcom->icc_path_apps);
+	}
+
+	if (usb_get_maximum_speed(&qcom->dwc3->dev) >= USB_SPEED_SUPER ||
+			usb_get_maximum_speed(&qcom->dwc3->dev) == USB_SPEED_UNKNOWN)
+		ret = icc_set_bw(qcom->icc_path_ddr,
+			USB_MEMORY_AVG_SS_BW, USB_MEMORY_PEAK_SS_BW);
+	else
+		ret = icc_set_bw(qcom->icc_path_ddr,
+			USB_MEMORY_AVG_HS_BW, USB_MEMORY_PEAK_HS_BW);
+
+	if (ret) {
+		dev_err(dev, "failed to set bandwidth for usb-ddr path: %d\n", ret);
+		return ret;
+	}
+
+	ret = icc_set_bw(qcom->icc_path_apps,
+		APPS_USB_AVG_BW, APPS_USB_PEAK_BW);
+
+	if (ret) {
+		dev_err(dev, "failed to set bandwidth for apps-usb path: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * dwc3_qcom_interconnect_exit() - Release interconnect path handles
+ * @qcom:			Pointer to the concerned usb core.
+ *
+ * This function is used to release interconnect path handle.
+ */
+static void dwc3_qcom_interconnect_exit(struct dwc3_qcom *qcom)
+{
+	icc_put(qcom->icc_path_ddr);
+	icc_put(qcom->icc_path_apps);
+}
+
 static void dwc3_qcom_disable_interrupts(struct dwc3_qcom *qcom)
 {
 	if (qcom->hs_phy_irq) {
@@ -239,7 +347,7 @@ static void dwc3_qcom_enable_interrupts(struct dwc3_qcom *qcom)
 static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
 {
 	u32 val;
-	int i;
+	int i, ret;
 
 	if (qcom->is_suspended)
 		return 0;
@@ -251,6 +359,10 @@ static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
 	for (i = qcom->num_clocks - 1; i >= 0; i--)
 		clk_disable_unprepare(qcom->clks[i]);
 
+	ret = dwc3_qcom_interconnect_disable(qcom);
+	if (ret)
+		dev_warn(qcom->dev, "failed to disable interconnect: %d\n", ret);
+
 	qcom->is_suspended = true;
 	dwc3_qcom_enable_interrupts(qcom);
 
@@ -276,6 +388,10 @@ static int dwc3_qcom_resume(struct dwc3_qcom *qcom)
 		}
 	}
 
+	ret = dwc3_qcom_interconnect_enable(qcom);
+	if (ret)
+		dev_warn(qcom->dev, "failed to enable interconnect: %d\n", ret);
+
 	/* Clear existing events from PHY related to L2 in/out */
 	dwc3_qcom_setbits(qcom->qscratch_base, PWR_EVNT_IRQ_STAT_REG,
 			  PWR_EVNT_LPM_IN_L2_MASK | PWR_EVNT_LPM_OUT_L2_MASK);
@@ -638,6 +754,10 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 		goto depopulate;
 	}
 
+	ret = dwc3_qcom_interconnect_init(qcom);
+	if (ret)
+		goto depopulate;
+
 	qcom->mode = usb_get_dr_mode(&qcom->dwc3->dev);
 
 	/* enable vbus override for device mode */
@@ -647,7 +767,7 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 	/* register extcon to override sw_vbus on Vbus change later */
 	ret = dwc3_qcom_register_extcon(qcom);
 	if (ret)
-		goto depopulate;
+		goto interconnect_exit;
 
 	device_init_wakeup(&pdev->dev, 1);
 	qcom->is_suspended = false;
@@ -657,6 +777,8 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 
 	return 0;
 
+interconnect_exit:
+	dwc3_qcom_interconnect_exit(qcom);
 depopulate:
 	if (np)
 		of_platform_depopulate(&pdev->dev);
@@ -687,6 +809,7 @@ static int dwc3_qcom_remove(struct platform_device *pdev)
 	}
 	qcom->num_clocks = 0;
 
+	dwc3_qcom_interconnect_exit(qcom);
 	reset_control_assert(qcom->resets);
 
 	pm_runtime_allow(dev);
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#2 lore raw

Re: [PATCH v10 1/2] usb: dwc3: qcom: Add interconnect support in dwc3 driver

Hi Sandeep,

Quoted 53 lines · Sandeep Maheswaram

Add interconnect support in dwc3-qcom driver to vote for bus bandwidth.

This requires for two different paths - from USB to DDR. The other is from APPS to USB.

---
 drivers/usb/dwc3/dwc3-qcom.c | 127 ++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 125 insertions(+), 2 deletions(-)
drivers/usb/dwc3/dwc3-qcom.c +12 -0
index e1e78e9..712efb7 100644
@@ -13,6 +13,7 @@
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/extcon.h>
+#include <linux/interconnect.h>
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
 #include <linux/phy/phy.h>
@@ -43,6 +44,14 @@
 #define SDM845_QSCRATCH_SIZE			0x400
 #define SDM845_DWC3_CORE_SIZE			0xcd00
 
+/* Interconnect path bandwidths in MBps */
+#define USB_MEMORY_AVG_HS_BW MBps_to_icc(240)
+#define USB_MEMORY_PEAK_HS_BW MBps_to_icc(700)
+#define USB_MEMORY_AVG_SS_BW  MBps_to_icc(1000)
+#define USB_MEMORY_PEAK_SS_BW MBps_to_icc(2500)
+#define APPS_USB_AVG_BW 0
+#define APPS_USB_PEAK_BW MBps_to_icc(40)
+
 struct dwc3_acpi_pdata {
 	u32			qscratch_base_offset;
 	u32			qscratch_base_size;
@@ -76,6 +85,8 @@ struct dwc3_qcom {
 	enum usb_dr_mode	mode;
 	bool			is_suspended;
 	bool			pm_suspended;
+	struct icc_path		*icc_path_ddr;
+	struct icc_path		*icc_path_apps;
 };
 
 static inline void dwc3_qcom_setbits(void __iomem *base, u32 offset, u32 val)
@@ -190,6 +201,103 @@ static int dwc3_qcom_register_extcon(struct dwc3_qcom *qcom)
 	return 0;
 }
 
+static int dwc3_qcom_interconnect_enable(struct dwc3_qcom *qcom)

drivers/usb/dwc3/dwc3-qcom.c static int dwc3_qcom_register_extcon(struct dwc3_qcom *qcom) · line 214

Quoted 10 lines
drivers/usb/dwc3/dwc3-qcom.c +10 -0
+{
+	int ret;
+
+	ret = icc_enable(qcom->icc_path_ddr);
+	if (ret)
+		return ret;
+
+	ret = icc_enable(qcom->icc_path_apps);
+	if (ret)
+		return icc_disable(qcom->icc_path_ddr);

You are returning the result of icc_disable(), but it should be the previous error. Just do

		icc_disable(qcom->icc_path_ddr);

and use the below statement for returning (if not it should be 'return 0').

Quoted 5 lines
drivers/usb/dwc3/dwc3-qcom.c +5 -0
+
+	return ret;
+}
+
+static int dwc3_qcom_interconnect_disable(struct dwc3_qcom *qcom)

drivers/usb/dwc3/dwc3-qcom.c static int dwc3_qcom_register_extcon(struct dwc3_qcom *qcom) · line 229

Quoted 10 lines
drivers/usb/dwc3/dwc3-qcom.c +10 -0
+{
+	int ret;
+
+	ret = icc_disable(qcom->icc_path_ddr);
+	if (ret)
+		return ret;
+
+	ret = icc_disable(qcom->icc_path_apps);
+	if (ret)
+		goto err_reenable_memory_path;

Please make the error handling in _enable() and _disable() symmetrical, either call icc_enable/disable() directly or use a goto in both functions (IMO the goto is not needed in this case, it makes the code more complex rather than simplifying it).

drivers/usb/dwc3/dwc3-qcom.c static int dwc3_qcom_register_extcon(struct dwc3_qcom *qcom) · line 235

Quoted 6 lines
drivers/usb/dwc3/dwc3-qcom.c +6 -0
+
+	return 0;
+
+	/* Re-enable things in the event of an error */
+err_reenable_memory_path:
+	dwc3_qcom_interconnect_enable(qcom);

Why this function which disables both paths and not just icc_enable(qcom->icc_path_ddr), analogous to dwc3_qcom_interconnect_enable()?

Quoted 35 lines
drivers/usb/dwc3/dwc3-qcom.c +35 -0
+
+	return ret;
+}
+
+/**
+ * dwc3_qcom_interconnect_init() - Get interconnect path handles
+ * and set bandwidhth.
+ * @qcom:			Pointer to the concerned usb core.
+ *
+ */
+static int dwc3_qcom_interconnect_init(struct dwc3_qcom *qcom)
+{
+	struct device *dev = qcom->dev;
+	int ret;
+
+	qcom->icc_path_ddr = of_icc_get(dev, "usb-ddr");
+	if (IS_ERR(qcom->icc_path_ddr)) {
+		dev_err(dev, "failed to get usb-ddr path: %ld\n",
+			PTR_ERR(qcom->icc_path_ddr));
+		return PTR_ERR(qcom->icc_path_ddr);
+	}
+
+	qcom->icc_path_apps = of_icc_get(dev, "apps-usb");
+	if (IS_ERR(qcom->icc_path_apps)) {
+		dev_err(dev, "failed to get apps-usb path: %ld\n",
+				PTR_ERR(qcom->icc_path_apps));
+		return PTR_ERR(qcom->icc_path_apps);
+	}
+
+	if (usb_get_maximum_speed(&qcom->dwc3->dev) >= USB_SPEED_SUPER ||
+			usb_get_maximum_speed(&qcom->dwc3->dev) == USB_SPEED_UNKNOWN)
+		ret = icc_set_bw(qcom->icc_path_ddr,
+			USB_MEMORY_AVG_SS_BW, USB_MEMORY_PEAK_SS_BW);
+	else
+		ret = icc_set_bw(qcom->icc_path_ddr,

drivers/usb/dwc3/dwc3-qcom.c static int dwc3_qcom_register_extcon(struct dwc3_qcom *qcom) · line 280

Quoted 10 lines
drivers/usb/dwc3/dwc3-qcom.c +10 -0
+			USB_MEMORY_AVG_HS_BW, USB_MEMORY_PEAK_HS_BW);
+
+	if (ret) {
+		dev_err(dev, "failed to set bandwidth for usb-ddr path: %d\n", ret);
+		return ret;
+	}
+
+	ret = icc_set_bw(qcom->icc_path_apps,
+		APPS_USB_AVG_BW, APPS_USB_PEAK_BW);
+

nit: remove empty line, the call and the if block belong together.

Quoted 4 lines
drivers/usb/dwc3/dwc3-qcom.c +4 -0
+	if (ret) {
+		dev_err(dev, "failed to set bandwidth for apps-usb path: %d\n", ret);
+		return ret;
+	}
Reviewed-by on v10 1/2
#3 lore raw

Re: [PATCH v10 1/2] usb: dwc3: qcom: Add interconnect support in dwc3 driver

In reply to Sandeep Maheswaram
Quoted 8 lines · Sandeep Maheswaram

Add interconnect support in dwc3-qcom driver to vote for bus bandwidth.

This requires for two different paths - from USB to DDR. The other is from APPS to USB.

#4 lore raw

Re: [PATCH v10 1/2] usb: dwc3: qcom: Add interconnect support in dwc3 driver

Quoted 11 lines · Matthias Kaehlcke
Quoted 8 lines · Sandeep Maheswaram

Add interconnect support in dwc3-qcom driver to vote for bus bandwidth.

This requires for two different paths - from USB to DDR. The other is from APPS to USB.

Sorry, that was meant for v11

#5 lore raw

PATCH v10 2/2 arm64: dts: qcom: sc7180: Add maximum speed property for DWC3 USB node

In reply to Sandeep Maheswaram

Adding maximum speed property for DWC3 USB node which can be used for setting interconnect bandwidth.

---
 arch/arm64/boot/dts/qcom/sc7180.dtsi | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/qcom/sc7180.dtsi +1 -0
index 16df08d..3fe759b6 100644
@@ -2656,6 +2656,7 @@
 				snps,dis_enblslpm_quirk;
 				phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
 				phy-names = "usb2-phy", "usb3-phy";
+				maximum-speed = "super-speed";
 			};
 		};
 
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation