bpf, x64: optimize JIT's pro/epilogue
Subsystems (5)
cover bpf, x64: optimize JIT's pro/epilogue
Hi!
This small set can be considered as a followup after recent addition of support for tailcalls in bpf subprograms and is focused on optimizing x64 JIT prologue and epilogue sections.
Turns out the popping tail call counter is not needed anymore and %rsp handling when stack depth is 0 can be skipped.
For longer explanations, please see commit messages.
Thank you,
Maciej
Maciej Fijalkowski (2):
bpf, x64: drop "pop %rcx" instruction on BPF JIT epilogue
bpf: x64: do not emit sub/add 0, %rsp when !stack_depth
arch/x86/net/bpf_jit_comp.c | 35 +++++++++++++++++++++++------------ 1 file changed, 23 insertions(+), 12 deletions(-)
Signature · 1 line
2.20.1
PATCH 1/2 bpf, x64: drop "pop %rcx" instruction on BPF JIT epilogue
Back when all of the callee-saved registers where always pushed to stack in x64 JIT prologue, tail call counter was placed at the bottom of the BPF program's stack frame that had a following layout:
+-------------+ | ret addr | +-------------+ | rbp | <- rbp +-------------+ | | | free space | | from: | | sub $x,%rsp | | | +-------------+ | rbx | +-------------+ | r13 | +-------------+ | r14 | +-------------+ | r15 | +-------------+ | tail call | <- rsp | counter | +-------------+
In order to restore the callee saved registers, epilogue needed to explicitly toss away the tail call counter via "pop %rbx" insn, so that %rsp would be back at the place where %r15 was stored.
Currently, the tail call counter is placed on stack *before* the callee saved registers (brackets on rbx through r15 mean that they are now pushed to stack only if they are used):
+-------------+ | ret addr | +-------------+ | rbp | <- rbp +-------------+ | | | free space | | from: | | sub $x,%rsp | | | +-------------+ | tail call | | counter | +-------------+ ( rbx ) +-------------+ ( r13 ) +-------------+ ( r14 ) +-------------+ ( r15 ) <- rsp +-------------+
For the record, the epilogue insns consist of (assuming all of the callee saved registers are used by program):
pop %r15 pop %r14 pop %r13 pop %rbx pop %rcx
leaveq
retq
"pop %rbx" for getting rid of tail call counter was not an option anymore as it would overwrite the restored value of %rbx register, so it was changed to use the %rcx register.
Since epilogue can start popping the callee saved registers right away without any additional work, the "pop %rcx" could be dropped altogether as "leave" insn will simply move the %rbp to %rsp. IOW, tail call counter does not need the explicit handling.
Having in mind the explanation above and the actual reason for that, let's piggy back on "leave" insn for discarding the tail call counter from stack and remove the "pop %rcx" from epilogue.
--- arch/x86/net/bpf_jit_comp.c | 2 -- 1 file changed, 2 deletions(-)
arch/x86/net/bpf_jit_comp.c +0 -2
@@ -1441,8 +1441,6 @@ xadd: if (is_imm8(insn->off))/* Update cleanup_addr */ ctx->cleanup_addr = proglen;pop_callee_regs (&prog, callee_regs_used); -if (tail_call_reachable) -EMIT1 (0x59 );/* pop rcx, get rid of tail_call_cnt */ EMIT1 (0xC9 );/* leave */ EMIT1 (0xC3 );/* ret */ break ;
Signature · 1 line
2.20.1
PATCH 2/2 bpf: x64: do not emit sub/add 0, %rsp when !stack_depth
In reply to Maciej FijalkowskiThere is no particular reason for keeping the "sub 0, %rsp" insn within the BPF's x64 JIT prologue.
When tail call code was skipping the whole prologue section these 7 bytes that represent the rsp subtraction could not be simply discarded as the jump target address would be broken. An option to address that would be to substitute it with nop7.
Right now tail call is skipping only first 11 bytes of target program's prologue and "sub X, %rsp" is the first insn that is processed, so if stack depth is zero then this insn could be omitted without the need for nop7 swap.
Therefore, do not emit the "sub 0, %rsp" in prologue when program is not making use of R10 register. Also, make the emission of "add X, %rsp" conditional in tail call code logic and take into account the presence of mentioned insn when calculating the jump offsets.
--- arch/x86/net/bpf_jit_comp.c | 33 +++++++++++++++++++++++---------- 1 file changed, 23 insertions(+), 10 deletions(-)
arch/x86/net/bpf_jit_comp.c +23 -10
@@ -281,7 +281,8 @@ static void emit_prologue(u8 **pprog, u32 stack_depth, bool ebpf_from_cbpf,EMIT1 (0x55 );/* push rbp */ EMIT3 (0x48 ,0x89 ,0xE5 );/* mov rbp, rsp */ /* sub rsp, rounded_stack_depth */ -EMIT3_off32 (0x48 ,0x81 ,0xEC ,round_up (stack_depth,8 )); +if (stack_depth) +EMIT3_off32 (0x48 ,0x81 ,0xEC ,round_up (stack_depth,8 ));if (tail_call_reachable)EMIT1 (0x50 );/* push rax */ *pprog = prog;
@@ -407,9 +408,9 @@ static void emit_bpf_tail_call_indirect(u8 **pprog, bool *callee_regs_used,int tcc_off =-4 -round_up (stack_depth,8 );u8 *prog = *pprog;int pop_bytes =0 ; -int off1 =49 ; -int off2 =38 ; -int off3 =16 ; +int off1 =42 ; +int off2 =31 ; +int off3 =9 ;int cnt =0 ;/* count the additional bytes used for popping callee regs from stack
@@ -421,6 +422,12 @@ static void emit_bpf_tail_call_indirect(u8 **pprog, bool *callee_regs_used, off2 += pop_bytes; off3 += pop_bytes; +if (stack_depth) { + off1 +=7 ; + off2 +=7 ; + off3 +=7 ; + } +/* * rdi - pointer to ctx * rsi - pointer to bpf_array
@@ -465,8 +472,9 @@ static void emit_bpf_tail_call_indirect(u8 **pprog, bool *callee_regs_used, prog = *pprog;EMIT1 (0x58 );/* pop rax */ -EMIT3_off32 (0x48 ,0x81 ,0xC4 ,/* add rsp, sd */ -round_up (stack_depth,8 )); +if (stack_depth) +EMIT3_off32 (0x48 ,0x81 ,0xC4 ,/* add rsp, sd */ +round_up (stack_depth,8 ));/* goto *(prog->bpf_func + X86_TAIL_CALL_OFFSET); */ EMIT4(0x48, 0x8B, 0x49, /* mov rcx, qword ptr [rcx + 32] */
@@ -491,7 +499,7 @@ static void emit_bpf_tail_call_direct(struct bpf_jit_poke_descriptor *poke,int tcc_off =-4 -round_up (stack_depth,8 );u8 *prog = *pprog;int pop_bytes =0 ; -int off1 =27 ; +int off1 =20 ;int poke_off;int cnt =0 ;
@@ -506,10 +514,14 @@ static void emit_bpf_tail_call_direct(struct bpf_jit_poke_descriptor *poke,* total bytes for: * - nop5/ jmpq $off * - pop callee regs -* - sub rsp, $val +* - sub rsp, $val if depth > 0 * - pop rax */ - poke_off =X86_PATCH_SIZE + pop_bytes +7 +1 ; + poke_off =X86_PATCH_SIZE + pop_bytes +1 ; +if (stack_depth) { + poke_off +=7 ; + off1 +=7 ; + }/* * if (tail_call_cnt > MAX_TAIL_CALL_CNT)
@@ -533,7 +545,8 @@ static void emit_bpf_tail_call_direct(struct bpf_jit_poke_descriptor *poke,pop_callee_regs (pprog, callee_regs_used); prog = *pprog;EMIT1 (0x58 );/* pop rax */ -EMIT3_off32 (0x48 ,0x81 ,0xC4 ,round_up (stack_depth,8 )); +if (stack_depth) +EMIT3_off32 (0x48 ,0x81 ,0xC4 ,round_up (stack_depth,8 ));memcpy (prog, ideal_nops[NOP_ATOMIC5 ],X86_PATCH_SIZE ); prog +=X86_PATCH_SIZE ;
Signature · 1 line
2.20.1
This series was applied to bpf/bpf-next.git (refs/heads/master):
Hello:
This series was applied to bpf/bpf-next.git (refs/heads/master):
Quoted 10 lines · On Tue, 29 Sep 2020 22:46:51 +0200 you wrote:
Hi!
This small set can be considered as a followup after recent addition of support for tailcalls in bpf subprograms and is focused on optimizing x64 JIT prologue and epilogue sections.
Turns out the popping tail call counter is not needed anymore and %rsp handling when stack depth is 0 can be skipped.
[...]
Here is the summary with links:
- [bpf-next,1/2] bpf, x64: drop "pop %rcx" instruction on BPF JIT epilogue
https://git.kernel.org/bpf/bpf-next/c/d207929d97ea - [bpf-next,2/2] bpf: x64: do not emit sub/add 0, %rsp when !stack_depth https://git.kernel.org/bpf/bpf-next/c/4d0b8c0b46a5
You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html