Skip to contentSkip to conversation

Bluetooth: hci_qca: Enhance retry logic in qca_setup

PATCH Superseded Balakrishna Godavarthi 2 participants 2 messages Oct 6, 2020

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Bluetooth: hci_qca: Enhance retry logic in qca_setup

Currently driver only retries to download FW if FW downloading is failed. Sometimes observed command timeout for version request command, if this happen on some platforms during boot time, then a reboot is needed to turn ON BT. Instead to avoid a reboot, now extended retry logic for version request command too.

---
 drivers/bluetooth/hci_qca.c | 34 ++++++++++++++++++----------------
 1 file changed, 18 insertions(+), 16 deletions(-)
drivers/bluetooth/hci_qca.c +18 -16
index 2d3f1f1..1c9a2d46 100644
@@ -1672,7 +1672,7 @@ static int qca_setup(struct hci_uart *hu)
 retry:
 	ret = qca_power_on(hdev);
 	if (ret)
-		return ret;
+		goto out;
 
 	clear_bit(QCA_SSR_TRIGGERED, &qca->flags);
 
@@ -1681,7 +1681,7 @@ static int qca_setup(struct hci_uart *hu)
 
 		ret = qca_read_soc_version(hdev, &soc_ver, soc_type);
 		if (ret)
-			return ret;
+			goto out;
 	} else {
 		qca_set_speed(hu, QCA_INIT_SPEED);
 	}
@@ -1691,7 +1691,7 @@ static int qca_setup(struct hci_uart *hu)
 	if (speed) {
 		ret = qca_set_speed(hu, QCA_OPER_SPEED);
 		if (ret)
-			return ret;
+			goto out;
 
 		qca_baudrate = qca_get_baudrate_value(speed);
 	}
@@ -1700,7 +1700,7 @@ static int qca_setup(struct hci_uart *hu)
 		/* Get QCA version information */
 		ret = qca_read_soc_version(hdev, &soc_ver, soc_type);
 		if (ret)
-			return ret;
+			goto out;
 	}
 
 	bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver);
@@ -1721,20 +1721,22 @@ static int qca_setup(struct hci_uart *hu)
 		 * patch/nvm-config is found, so run with original fw/config.
 		 */
 		ret = 0;
-	} else {
-		if (retries < MAX_INIT_RETRIES) {
-			qca_power_shutdown(hu);
-			if (hu->serdev) {
-				serdev_device_close(hu->serdev);
-				ret = serdev_device_open(hu->serdev);
-				if (ret) {
-					bt_dev_err(hdev, "failed to open port");
-					return ret;
-				}
+	}
+
+out:
+	if (ret && retries < MAX_INIT_RETRIES) {
+		bt_dev_warn(hdev, "Retry BT power ON:%d", retries);
+		qca_power_shutdown(hu);
+		if (hu->serdev) {
+			serdev_device_close(hu->serdev);
+			ret = serdev_device_open(hu->serdev);
+			if (ret) {
+				bt_dev_err(hdev, "failed to open port");
+				return ret;
 			}
-			retries++;
-			goto retry;
 		}
+		retries++;
+		goto retry;
 	}
 
 	/* Setup bdaddr */
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Reviewed-by on v1 1/1
#1 lore raw
Quoted 8 lines · Balakrishna Godavarthi

Currently driver only retries to download FW if FW downloading is failed. Sometimes observed command timeout for version request command, if this happen on some platforms during boot time, then a reboot is needed to turn ON BT. Instead to avoid a reboot, now extended retry logic for version request command too.