hw/block: m25p80: Don't write to flash if write is disabled
PATCH v3 1/2 hw/block: m25p80: Don't write to flash if write is disabled
From: Bin Meng <[email protected]>
When write is disabled, the write to flash should be avoided in flash_write8().
---
(no changes since v2)
Changes in v2:
- new patch: honor write enable flag in flash write
hw/block/m25p80.c | 1 + 1 file changed, 1 insertion(+)
hw/block/m25p80.c +1 -0
@@ -594,6 +594,7 @@ void flash_write8(Flash *s, uint32_t addr, uint8_t data)if (!s->write_enable) {qemu_log_mask (LOG_GUEST_ERROR ,"M25P80: write with write protect!\n" ); +return ; }if ((prev ^ data) & data) {
Signature · 1 line
2.7.4
PATCH v3 2/2 hw/block: m25p80: Implement AAI-WP command support for SST flashes
From: Xuzhou Cheng <[email protected]>
Auto Address Increment (AAI) Word-Program is a special command of SST flashes. AAI-WP allows multiple bytes of data to be programmed without re-issuing the next sequential address location.
---
Changes in v3:
- initialize aai_enable to false in reset_memory()
Changes in v2:
- add aai_enable into the vmstate
- validate AAI command before decoding a new command
- log guest errors during AAI_WP command handling
- report AAI status in the status register
- abort AAI programming when address is wrapped
- make sure AAI programming starts from the even address
hw/block/m25p80.c | 61 +++++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 61 insertions(+)
hw/block/m25p80.c +61 -0
@@ -359,6 +359,7 @@ typedef enum {QPP_4 =0x34 ,RDID_90 =0x90 ,RDID_AB =0xab , +AAI_WP =0xad ,ERASE_4K =0x20 , ERASE4_4K = 0x21,
@@ -449,6 +450,7 @@ struct Flash {bool four_bytes_address_mode;bool reset_enable;bool quad_enable; +bool aai_enable;uint8_t ear;int64_t dirty_page;
@@ -664,6 +666,11 @@ static void complete_collecting_data(Flash *s)case PP4_4 : s->state =STATE_PAGE_PROGRAM ;break ; +case AAI_WP : +/* AAI programming starts from the even address */ + s->cur_addr &= ~BIT (0 ); + s->state =STATE_PAGE_PROGRAM ; +break ;case READ :case READ4 :case FAST_READ :
@@ -762,6 +769,7 @@ static void reset_memory(Flash *s) s->write_enable = false; s->reset_enable = false; s->quad_enable = false; + s->aai_enable = false;switch (get_man (s)) {case MAN_NUMONYX :
@@ -932,6 +940,15 @@ static void decode_qio_read_cmd(Flash *s) s->state =STATE_COLLECTING_DATA ; } +static bool is_valid_aai_cmd (uint32_t value) +{ +if (value ==AAI_WP || value ==WRDI || value ==RDSR ) { +return true; + }else { +return false; + } +} +static void decode_new_cmd (Flash *s,uint32_t value) {int i;
@@ -943,6 +960,11 @@ static void decode_new_cmd(Flash *s, uint32_t value) s->reset_enable = false; } +if (get_man (s) ==MAN_SST && s->aai_enable && !is_valid_aai_cmd (value)) { +qemu_log_mask (LOG_GUEST_ERROR , +"M25P80: Invalid cmd within AAI programming sequence" ); + } +switch (value) {case ERASE_4K :
@@ -1008,6 +1030,9 @@ static void decode_new_cmd(Flash *s, uint32_t value)case WRDI : s->write_enable = false; +if (get_man (s) ==MAN_SST ) { + s->aai_enable = false; + }break ;case WREN : s->write_enable = true;
@@ -1018,6 +1043,10 @@ static void decode_new_cmd(Flash *s, uint32_t value)if (get_man (s) ==MAN_MACRONIX ) { s->data[0 ] |= (!!s->quad_enable) <<6 ; } +if (get_man (s) ==MAN_SST ) { + s->data[0 ] |= (!!s->aai_enable) <<6 ; + } + s->pos =0 ; s->len =1 ; s->data_read_loop = true;
@@ -1160,6 +1189,24 @@ static void decode_new_cmd(Flash *s, uint32_t value)case RSTQIO : s->quad_enable = false;break ; +case AAI_WP : +if (get_man (s) ==MAN_SST ) { +if (s->write_enable) { +if (s->aai_enable) { + s->state =STATE_PAGE_PROGRAM ; + }else { + s->aai_enable = true; + s->needed_bytes =get_addr_length (s); + s->state =STATE_COLLECTING_DATA ; + } + }else { +qemu_log_mask (LOG_GUEST_ERROR , +"M25P80: AAI_WP with write protect\n" ); + } + }else { +qemu_log_mask (LOG_GUEST_ERROR ,"M25P80: Unknown cmd %x\n" , value); + } +break ;default : s->pos =0 ; s->len =1 ;
@@ -1205,6 +1252,19 @@ static uint32_t m25p80_transfer8(SSISlave *ss, uint32_t tx)trace_m25p80_page_program (s, s->cur_addr, (uint8_t )tx);flash_write8 (s, s->cur_addr, (uint8_t )tx); s->cur_addr = (s->cur_addr +1 ) & (s->size -1 ); + +if (get_man (s) ==MAN_SST && s->aai_enable && s->cur_addr ==0 ) { +/* +* There is no wrap mode during AAI programming once the highest +* unprotected memory address is reached. The Write-Enable-Latch +* bit is automatically reset, and AAI programming mode aborts. +*/ +qemu_log_mask (LOG_GUEST_ERROR , +"M25P80: AAI highest memory address reached" ); + s->write_enable = false; + s->aai_enable = false; + } +break ;case STATE_READ :
@@ -1372,6 +1432,7 @@ static const VMStateDescription vmstate_m25p80 = {VMSTATE_UINT32 (volatile_cfg, Flash),VMSTATE_UINT32 (enh_volatile_cfg, Flash),VMSTATE_BOOL (quad_enable, Flash), +VMSTATE_BOOL (aai_enable, Flash),VMSTATE_UINT8 (spansion_cr1nv, Flash),VMSTATE_UINT8 (spansion_cr2nv, Flash), VMSTATE_UINT8(spansion_cr3nv, Flash),
Signature · 1 line
2.7.4
Re: [PATCH v3 2/2] hw/block: m25p80: Implement AAI-WP command support for SST flashes
Hi Francisco,
Quoted 23 lines · Bin Meng
From: Xuzhou Cheng <[email protected]>
Auto Address Increment (AAI) Word-Program is a special command of SST flashes. AAI-WP allows multiple bytes of data to be programmed without re-issuing the next sequential address location.
Signed-off-by Xuzhou Cheng <[email protected]>Signed-off-by Bin Meng <[email protected]>---
Changes in v3:
- initializeaai_enableto false inreset_memory()Changes in v2:
- addaai_enableinto the vmstate
- validate AAI command before decoding a new command
- log guest errors duringAAI_WPcommand handling
- report AAI status in the status register
- abort AAI programming when address is wrapped
- make sure AAI programming starts from the even address
Quoted 3 lines
hw/block/m25p80.c | 61 +++++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 61 insertions(+)
Any comments for this series?
Regards,
Bin
Re: [PATCH v3 2/2] hw/block: m25p80: Implement AAI-WP command support for SST flashes
In reply to Bin MengHi Bin,
Quoted 66 lines · Bin Meng
From: Xuzhou Cheng <[email protected]>
Auto Address Increment (AAI) Word-Program is a special command of SST flashes. AAI-WP allows multiple bytes of data to be programmed without re-issuing the next sequential address location.
Signed-off-by Xuzhou Cheng <[email protected]>Signed-off-by Bin Meng <[email protected]>---
Changes in v3:
- initializeaai_enableto false inreset_memory()Changes in v2:
- addaai_enableinto the vmstate
- validate AAI command before decoding a new command
- log guest errors duringAAI_WPcommand handling
- report AAI status in the status register
- abort AAI programming when address is wrapped
- make sure AAI programming starts from the even addresshw/block/m25p80.c | 61 +++++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 61 insertions(+)hw/block/m25p80.c +8
-0@@ -359,6 +359,7 @@ typedef enum {QPP_4 =0x34 ,RDID_90 =0x90 ,RDID_AB =0xab , +AAI_WP =0xad ,ERASE_4K =0x20 , ERASE4_4K = 0x21,@@ -449,6 +450,7 @@ struct Flash {bool four_bytes_address_mode;bool reset_enable;bool quad_enable; +bool aai_enable;uint8_t ear;int64_t dirty_page;@@ -664,6 +666,11 @@ static void complete_collecting_data(Flash *s)case PP4_4 : s->state =STATE_PAGE_PROGRAM ;break ; +case AAI_WP : +/* AAI programming starts from the even address */ + s->cur_addr &= ~BIT (0 ); + s->state =STATE_PAGE_PROGRAM ; +break ;case READ :case READ4 :case FAST_READ :@@ -762,6 +769,7 @@ static void reset_memory(Flash *s) s->write_enable = false; s->reset_enable = false; s->quad_enable = false; + s->aai_enable = false;switch (get_man (s)) {case MAN_NUMONYX :
hw/block/m25p80.c static void decode_qio_read_cmd(Flash *s) · line 949
Quoted 10 lines
hw/block/m25p80.c +7
-0@@ -932,6 +940,15 @@ static void decode_qio_read_cmd(Flash *s) s->state =STATE_COLLECTING_DATA ; } +static bool is_valid_aai_cmd (uint32_t value) +{ +if (value ==AAI_WP || value ==WRDI || value ==RDSR ) { +return true; + }else { +return false; + }
For fewer lines (perhaps also rename value -> cmd):
return value == AAI_WP || value == WRDI || value == RDSR;
Quoted 64 lines
hw/block/m25p80.c +32
-0+} +static void decode_new_cmd (Flash *s,uint32_t value) {int i;@@ -943,6 +960,11 @@ static void decode_new_cmd(Flash *s, uint32_t value) s->reset_enable = false; } +if (get_man (s) ==MAN_SST && s->aai_enable && !is_valid_aai_cmd (value)) { +qemu_log_mask (LOG_GUEST_ERROR , +"M25P80: Invalid cmd within AAI programming sequence" ); + } +switch (value) {case ERASE_4K :@@ -1008,6 +1030,9 @@ static void decode_new_cmd(Flash *s, uint32_t value)case WRDI : s->write_enable = false; +if (get_man (s) ==MAN_SST ) { + s->aai_enable = false; + }break ;case WREN : s->write_enable = true;@@ -1018,6 +1043,10 @@ static void decode_new_cmd(Flash *s, uint32_t value)if (get_man (s) ==MAN_MACRONIX ) { s->data[0 ] |= (!!s->quad_enable) <<6 ; } +if (get_man (s) ==MAN_SST ) { + s->data[0 ] |= (!!s->aai_enable) <<6 ; + } + s->pos =0 ; s->len =1 ; s->data_read_loop = true;@@ -1160,6 +1189,24 @@ static void decode_new_cmd(Flash *s, uint32_t value)case RSTQIO : s->quad_enable = false;break ; +case AAI_WP : +if (get_man (s) ==MAN_SST ) { +if (s->write_enable) { +if (s->aai_enable) { + s->state =STATE_PAGE_PROGRAM ; + }else { + s->aai_enable = true; + s->needed_bytes =get_addr_length (s); + s->state =STATE_COLLECTING_DATA ; + } + }else { +qemu_log_mask (LOG_GUEST_ERROR , +"M25P80: AAI_WP with write protect\n" ); + } + }else { +qemu_log_mask (LOG_GUEST_ERROR ,"M25P80: Unknown cmd %x\n" , value); + } +break ;default : s->pos =0 ; s->len =1 ;
hw/block/m25p80.c static uint32_t m25p80_transfer8(SSISlave *ss, uint32_t tx) · line 1256
Quoted 5 lines
hw/block/m25p80.c +2
-0@@ -1205,6 +1252,19 @@ static uint32_t m25p80_transfer8(SSISlave *ss, uint32_t tx)trace_m25p80_page_program (s, s->cur_addr, (uint8_t )tx);flash_write8 (s, s->cur_addr, (uint8_t )tx); s->cur_addr = (s->cur_addr +1 ) & (s->size -1 ); + +if (get_man (s) ==MAN_SST && s->aai_enable && s->cur_addr ==0 ) {
I had a another look at above and think [1] actually speeks about wrapping when hitting into protected areas. Since we do not handle those at the moment we can just remove this portion in case you agree with me.
Quoted 15 lines
hw/block/m25p80.c +11
-0+/* +* There is no wrap mode during AAI programming once the highest +* unprotected memory address is reached. The Write-Enable-Latch +* bit is automatically reset, and AAI programming mode aborts. +*/ +qemu_log_mask (LOG_GUEST_ERROR , +"M25P80: AAI highest memory address reached" ); + s->write_enable = false; + s->aai_enable = false; + } +break ;case STATE_READ :
hw/block/m25p80.c static const VMStateDescription vmstate_m25p80 = { · line 1435
Quoted 4 lines
hw/block/m25p80.c +1
-0@@ -1372,6 +1432,7 @@ static const VMStateDescription vmstate_m25p80 = {VMSTATE_UINT32 (volatile_cfg, Flash),VMSTATE_UINT32 (enh_volatile_cfg, Flash),VMSTATE_BOOL (quad_enable, Flash), + VMSTATE_BOOL(aai_enable, Flash),
Above we will have to be put into a subsection (for not breaking migration). In 'docs/devel/migration.rst' one can read more about those (and in the file there's one already that can be looked into).
The rest of the patch looks good to me!
Best regards,
Francisco Iglesias
Quoted 6 lines
hw/block/m25p80.c +0
-0VMSTATE_UINT8 (spansion_cr1nv, Flash),VMSTATE_UINT8 (spansion_cr2nv, Flash), VMSTATE_UINT8(spansion_cr3nv, Flash),Signature · 1 line
2.7.4
Re: [PATCH v3 2/2] hw/block: m25p80: Implement AAI-WP command support for SST flashes
Hi Francisco,
Quoted 83 lines · Francisco Iglesias
Hi Bin,
Quoted 66 lines · Bin Meng
From: Xuzhou Cheng <[email protected]>
Auto Address Increment (AAI) Word-Program is a special command of SST flashes. AAI-WP allows multiple bytes of data to be programmed without re-issuing the next sequential address location.
Signed-off-by Xuzhou Cheng <[email protected]>Signed-off-by Bin Meng <[email protected]>---
Changes in v3:
- initializeaai_enableto false inreset_memory()Changes in v2:
- addaai_enableinto the vmstate
- validate AAI command before decoding a new command
- log guest errors duringAAI_WPcommand handling
- report AAI status in the status register
- abort AAI programming when address is wrapped
- make sure AAI programming starts from the even addresshw/block/m25p80.c | 61 +++++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 61 insertions(+)hw/block/m25p80.c +8
-0@@ -359,6 +359,7 @@ typedef enum {QPP_4 =0x34 ,RDID_90 =0x90 ,RDID_AB =0xab , +AAI_WP =0xad ,ERASE_4K =0x20 , ERASE4_4K = 0x21,@@ -449,6 +450,7 @@ struct Flash {bool four_bytes_address_mode;bool reset_enable;bool quad_enable; +bool aai_enable;uint8_t ear;int64_t dirty_page;@@ -664,6 +666,11 @@ static void complete_collecting_data(Flash *s)case PP4_4 : s->state =STATE_PAGE_PROGRAM ;break ; +case AAI_WP : +/* AAI programming starts from the even address */ + s->cur_addr &= ~BIT (0 ); + s->state =STATE_PAGE_PROGRAM ; +break ;case READ :case READ4 :case FAST_READ :@@ -762,6 +769,7 @@ static void reset_memory(Flash *s) s->write_enable = false; s->reset_enable = false; s->quad_enable = false; + s->aai_enable = false;switch (get_man (s)) {case MAN_NUMONYX :hw/block/m25p80.c static void decode_qio_read_cmd(Flash *s) · line 949
Quoted 10 lines
hw/block/m25p80.c +7
-0@@ -932,6 +940,15 @@ static void decode_qio_read_cmd(Flash *s) s->state =STATE_COLLECTING_DATA ; } +static bool is_valid_aai_cmd (uint32_t value) +{ +if (value ==AAI_WP || value ==WRDI || value ==RDSR ) { +return true; + }else { +return false; + }For fewer lines (perhaps also rename value -> cmd):
Quoted 1 line
return value ==
AAI_WP|| value == WRDI || value == RDSR;
Sure!
Quoted 67 lines
Quoted 67 lines
hw/block/m25p80.c +32
-0+} +static void decode_new_cmd (Flash *s,uint32_t value) {int i;@@ -943,6 +960,11 @@ static void decode_new_cmd(Flash *s, uint32_t value) s->reset_enable = false; } +if (get_man (s) ==MAN_SST && s->aai_enable && !is_valid_aai_cmd (value)) { +qemu_log_mask (LOG_GUEST_ERROR , +"M25P80: Invalid cmd within AAI programming sequence" ); + } +switch (value) {case ERASE_4K :@@ -1008,6 +1030,9 @@ static void decode_new_cmd(Flash *s, uint32_t value)case WRDI : s->write_enable = false; +if (get_man (s) ==MAN_SST ) { + s->aai_enable = false; + }break ;case WREN : s->write_enable = true;@@ -1018,6 +1043,10 @@ static void decode_new_cmd(Flash *s, uint32_t value)if (get_man (s) ==MAN_MACRONIX ) { s->data[0 ] |= (!!s->quad_enable) <<6 ; } +if (get_man (s) ==MAN_SST ) { + s->data[0 ] |= (!!s->aai_enable) <<6 ; + } + s->pos =0 ; s->len =1 ; s->data_read_loop = true;@@ -1160,6 +1189,24 @@ static void decode_new_cmd(Flash *s, uint32_t value)case RSTQIO : s->quad_enable = false;break ; +case AAI_WP : +if (get_man (s) ==MAN_SST ) { +if (s->write_enable) { +if (s->aai_enable) { + s->state =STATE_PAGE_PROGRAM ; + }else { + s->aai_enable = true; + s->needed_bytes =get_addr_length (s); + s->state =STATE_COLLECTING_DATA ; + } + }else { +qemu_log_mask (LOG_GUEST_ERROR , +"M25P80: AAI_WP with write protect\n" ); + } + }else { +qemu_log_mask (LOG_GUEST_ERROR ,"M25P80: Unknown cmd %x\n" , value); + } +break ;default : s->pos =0 ; s->len =1 ;@@ -1205,6 +1252,19 @@ static uint32_t m25p80_transfer8(SSISlave *ss, uint32_t tx)trace_m25p80_page_program (s, s->cur_addr, (uint8_t )tx);
Quoted 9 lines
hw/block/m25p80.c static uint32_t m25p80_transfer8(SSISlave *ss, uint32_t tx) · line 1256
Quoted 4 lines
hw/block/m25p80.c +2
-0flash_write8 (s, s->cur_addr, (uint8_t )tx); s->cur_addr = (s->cur_addr +1 ) & (s->size -1 ); + +if (get_man (s) ==MAN_SST && s->aai_enable && s->cur_addr ==0 ) {I had a another look at above and think [1] actually speeks about wrapping when hitting into protected areas. Since we do not handle those at the moment we can just remove this portion in case you agree with me.
The datasheet actually says:
1. "An AAI Word program instruction pointing to a protected memory area will be ignored."
2. "There is no wrap mode during AAI programming once the highest unprotected memory address is reached."
In QEMU protected block is implemented for m25p80 so 1 can be ignored. 2 indicates that AAI stops at the highest unprotected memory address, ie. no wrap mode like what READ or FAST READ does.
We've also tested on a real SST flash and tests showed that AAI stops at the highest memory address (note the whole flash is unprotected)
Quoted 14 lines
Quoted 14 lines
hw/block/m25p80.c +11
-0+/* +* There is no wrap mode during AAI programming once the highest +* unprotected memory address is reached. The Write-Enable-Latch +* bit is automatically reset, and AAI programming mode aborts. +*/ +qemu_log_mask (LOG_GUEST_ERROR , +"M25P80: AAI highest memory address reached" ); + s->write_enable = false; + s->aai_enable = false; + } +break ;
Quoted 11 lines
hw/block/m25p80.c static const VMStateDescription vmstate_m25p80 = { · line 1435
Quoted 6 lines
hw/block/m25p80.c +1
-0case STATE_READ :@@ -1372,6 +1432,7 @@ static const VMStateDescription vmstate_m25p80 = {VMSTATE_UINT32 (volatile_cfg, Flash),VMSTATE_UINT32 (enh_volatile_cfg, Flash),VMSTATE_BOOL (quad_enable, Flash), + VMSTATE_BOOL(aai_enable, Flash),Above we will have to be put into a subsection (for not breaking migration). In '
docs/devel/migration.rst' one can read more about those (and in the file there's one already that can be looked into).
Will do in v4.
Quoted 1 line
The rest of the patch looks good to me!
Thanks for the review!
Regards,
Bin