add NXP imx8mp usb support
v5 cover add NXP imx8mp usb support
NXP imx8MPlus integrates 2 indentical dwc3 3.30b IP with additional wakeup logic to support low power, this wakeup logic has a separated interrupt which can generate events with suspend clock(32K); due to SoC integration limitation, it only can support 32 bits DMA, so add dma-ranges property,
changes for v5
- Remove "Items" of compatible in binding doc [1/4]
- Add Krzysztof's R-b tag for patches [3-4/4].
changes for v4:
- Use dma-ranges property to limit 32bits DMA, so don't need the new property "xhci-64bit-support-disable".
- Fix binding doc to pass dt_binding_check dtbs_check.
changes for v3:
- Add dwc3 core related clocks into dwc3 core node, and glue layer driver only handle the clocks(hsio and suspend) for glue block, this is to match real HW.
- Change to use property "xhci-64bit-support-disable" to disable 64bit DMA as imx8mp USB integration actully can't support it, so remove platform data in v2.
- Some changes of imx8mp usb driver binding doc to address comments from Rob
Changes for v2:
- Drop the 2 patches for new property("snps,xhci-dis-64bit-support-quirk") introduction, as suggested, imply by SoC compatible string, this is done by introduce dwc3 core platform data and pass the xhci_plat_priv to xhci-plat for those xhci quirks, so a new patch added:
[1/5] usb: dwc3: add platform data to dwc3 core device to pass data. this patch is based on Peter's one patch which is also in review:
https://patchwork.kernel.org/patch/11640945/
- dts change, use the USB power function of TRL logic instead of a always-on regulator to control vbus on/off.
- Some changes to address Peter's command on patch [2/5].
Li Jun (4):
dt-bindings: usb: dwc3-imx8mp: add imx8mp dwc3 glue bindings
usb: dwc3: add imx8mp dwc3 glue layer driver
arm64: dtsi: imx8mp: add usb nodes
arm64: dts: imx8mp-evk: enable usb1 as host mode
.../devicetree/bindings/usb/fsl,imx8mp-dwc3.yaml | 105 ++++++ arch/arm64/boot/dts/freescale/imx8mp-evk.dts | 21 ++ arch/arm64/boot/dts/freescale/imx8mp.dtsi | 82 +++++ drivers/usb/dwc3/Kconfig | 10 + drivers/usb/dwc3/Makefile | 1 + drivers/usb/dwc3/dwc3-imx8mp.c | 363 +++++++++++++++++++++ 6 files changed, 582 insertions(+) create mode 100644 Documentation/devicetree/bindings/usb/fsl,imx8mp-dwc3.yaml create mode 100644 drivers/usb/dwc3/dwc3-imx8mp.c
Signature · 1 line
2.7.4
PATCH RESEND v5 1/4 dt-bindings: usb: dwc3-imx8mp: add imx8mp dwc3 glue bindings
NXP imx8mp integrates 2 dwc3 3.30b IP and add some wakeup logic to support low power mode, the glue layer is for this wakeup functionality, which has a separated interrupt, can support wakeup from U3 and connect events for host, and vbus wakeup for device.
--- .../devicetree/bindings/usb/fsl,imx8mp-dwc3.yaml | 105 +++++++++++++++++++++ 1 file changed, 105 insertions(+)
Documentation/devicetree/bindings/usb/fsl,imx8mp-dwc3.yaml new file +105 -0
@@ -0,0 +1,105 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2020 NXP +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/fsl,imx8mp-dwc3.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP iMX8MP Soc USB Controller + +maintainers: + - Li Jun <[email protected]> + +properties: + compatible: + const: fsl,imx8mp-dwc3 + + reg: + maxItems: 1 + description: Address and length of the register set for the wrapper of + dwc3 core on the SOC. + + "#address-cells": + enum: [ 1, 2 ] + + "#size-cells": + enum: [ 1, 2 ] + + dma-ranges: + description: + See section 2.3.9 of the DeviceTree Specification. + + ranges: true + + interrupts: + maxItems: 1 + description: The interrupt that is asserted when a wakeup event is + received. + + clocks: + description: + A list of phandle and clock-specifier pairs for the clocks + listed in clock-names. + items: + - description: system hsio root clock. + - description: suspend clock, used for usb wakeup logic. + + clock-names: + items: + - const: hsio + - const: suspend + +# Required child node: + +patternProperties: + "^dwc3@[0-9a-f]+$": + type: object + description: + A child node must exist to represent the core DWC3 IP block + The content of the node is defined in dwc3.txt. + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + - dma-ranges + - ranges + - clocks + - clock-names + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx8mp-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + usb3_0: usb@32f10100 { + compatible = "fsl,imx8mp-dwc3"; + reg = <0x32f10100 0x8>; + clocks = <&clk IMX8MP_CLK_HSIO_ROOT>, + <&clk IMX8MP_CLK_USB_ROOT>; + clock-names = "hsio", "suspend"; + interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <1>; + dma-ranges = <0x40000000 0x40000000 0xc0000000>; + ranges; + + dwc3@38100000 { + compatible = "snps,dwc3"; + reg = <0x38100000 0x10000>; + clocks = <&clk IMX8MP_CLK_HSIO_AXI>, + <&clk IMX8MP_CLK_USB_CORE_REF>, + <&clk IMX8MP_CLK_USB_ROOT>; + clock-names = "bus_early", "ref", "suspend"; + assigned-clocks = <&clk IMX8MP_CLK_HSIO_AXI>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_500M>; + assigned-clock-rates = <500000000>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usb3_phy0>, <&usb3_phy0>; + phy-names = "usb2-phy", "usb3-phy"; + snps,dis-u2-freeclk-exists-quirk; + }; + };
Signature · 1 line
2.7.4
PATCH RESEND v5 2/4 usb: dwc3: add imx8mp dwc3 glue layer driver
In reply to Li Junimx8mp SoC integrate dwc3 3.30b IP and has some customizations to support low power, which has a seprated wakeup irq and additional logic to wakeup usb from low power mode both for host mode and device mode.
--- drivers/usb/dwc3/Kconfig | 10 ++ drivers/usb/dwc3/Makefile | 1 + drivers/usb/dwc3/dwc3-imx8mp.c | 363 +++++++++++++++++++++++++++++++++++++++++ 3 files changed, 374 insertions(+)
drivers/usb/dwc3/Kconfig +10 -0
@@ -139,4 +139,14 @@ config USB_DWC3_QCOM for peripheral mode support. Say 'Y' or 'M' if you have one such device. +config USB_DWC3_IMX8MP + tristate "NXP iMX8MP Platform" + depends on OF && COMMON_CLK + depends on (ARCH_MXC && ARM64) || COMPILE_TEST + default USB_DWC3 + help + NXP iMX8M Plus SoC use DesignWare Core IP for USB2/3 + functionality. + Say 'Y' or 'M' if you have one such device. + endif
drivers/usb/dwc3/Makefile +1 -0
@@ -51,3 +51,4 @@ obj-$(CONFIG_USB_DWC3_MESON_G12A) += dwc3-meson-g12a.o obj-$(CONFIG_USB_DWC3_OF_SIMPLE) += dwc3-of-simple.o obj-$(CONFIG_USB_DWC3_ST) += dwc3-st.o obj-$(CONFIG_USB_DWC3_QCOM) += dwc3-qcom.o +obj-$(CONFIG_USB_DWC3_IMX8MP) += dwc3-imx8mp.o
drivers/usb/dwc3/dwc3-imx8mp.c new file +363 -0
363 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH RESEND v5 3/4 arm64: dtsi: imx8mp: add usb nodes
In reply to Li Junimx8mp integrates 2 identical dwc3 based USB3 controllers and Synopsys phys, each instance has additional wakeup logic to support low power mode, so the glue layer need a node with dwc3 core sub node.
--- arch/arm64/boot/dts/freescale/imx8mp.dtsi | 82 +++++++++++++++++++++++++++++++ 1 file changed, 82 insertions(+)
arch/arm64/boot/dts/freescale/imx8mp.dtsi +82 -0
@@ -788,5 +788,87 @@ reg = <0x3d800000 0x400000>; interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; }; + + usb3_phy0: usb-phy@381f0040 { + compatible = "fsl,imx8mp-usb-phy"; + reg = <0x381f0040 0x40>; + clocks = <&clk IMX8MP_CLK_USB_PHY_ROOT>; + clock-names = "phy"; + assigned-clocks = <&clk IMX8MP_CLK_USB_PHY_REF>; + assigned-clock-parents = <&clk IMX8MP_CLK_24M>; + #phy-cells = <0>; + status = "disabled"; + }; + + usb3_0: usb@32f10100 { + compatible = "fsl,imx8mp-dwc3"; + reg = <0x32f10100 0x8>; + clocks = <&clk IMX8MP_CLK_HSIO_ROOT>, + <&clk IMX8MP_CLK_USB_ROOT>; + clock-names = "hsio", "suspend"; + interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <1>; + dma-ranges = <0x40000000 0x40000000 0xc0000000>; + ranges; + status = "disabled"; + + usb_dwc3_0: dwc3@38100000 { + compatible = "snps,dwc3"; + reg = <0x38100000 0x10000>; + clocks = <&clk IMX8MP_CLK_HSIO_AXI>, + <&clk IMX8MP_CLK_USB_CORE_REF>, + <&clk IMX8MP_CLK_USB_ROOT>; + clock-names = "bus_early", "ref", "suspend"; + assigned-clocks = <&clk IMX8MP_CLK_HSIO_AXI>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_500M>; + assigned-clock-rates = <500000000>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usb3_phy0>, <&usb3_phy0>; + phy-names = "usb2-phy", "usb3-phy"; + snps,dis-u2-freeclk-exists-quirk; + }; + + }; + + usb3_phy1: usb-phy@382f0040 { + compatible = "fsl,imx8mp-usb-phy"; + reg = <0x382f0040 0x40>; + clocks = <&clk IMX8MP_CLK_USB_PHY_ROOT>; + clock-names = "phy"; + assigned-clocks = <&clk IMX8MP_CLK_USB_PHY_REF>; + assigned-clock-parents = <&clk IMX8MP_CLK_24M>; + #phy-cells = <0>; + }; + + usb3_1: usb@32f10108 { + compatible = "fsl,imx8mp-dwc3"; + reg = <0x32f10108 0x8>; + clocks = <&clk IMX8MP_CLK_HSIO_ROOT>, + <&clk IMX8MP_CLK_USB_ROOT>; + clock-names = "hsio", "suspend"; + interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <1>; + dma-ranges = <0x40000000 0x40000000 0xc0000000>; + ranges; + status = "disabled"; + + usb_dwc3_1: dwc3@38200000 { + compatible = "snps,dwc3"; + reg = <0x38200000 0x10000>; + clocks = <&clk IMX8MP_CLK_HSIO_AXI>, + <&clk IMX8MP_CLK_USB_CORE_REF>, + <&clk IMX8MP_CLK_USB_ROOT>; + clock-names = "bus_early", "ref", "suspend"; + assigned-clocks = <&clk IMX8MP_CLK_HSIO_AXI>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_500M>; + assigned-clock-rates = <500000000>; + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usb3_phy1>, <&usb3_phy1>; + phy-names = "usb2-phy", "usb3-phy"; + snps,dis-u2-freeclk-exists-quirk; + }; + }; }; };
Signature · 1 line
2.7.4
PATCH RESEND v5 4/4 arm64: dts: imx8mp-evk: enable usb1 as host mode
In reply to Li JunEnable usb host port with type-A connector on imx8mp-evk board.
--- arch/arm64/boot/dts/freescale/imx8mp-evk.dts | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)
arch/arm64/boot/dts/freescale/imx8mp-evk.dts +21 -0
@@ -127,6 +127,21 @@ status = "okay"; }; +&usb3_phy1 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&usb_dwc3_1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb1_vbus>; + dr_mode = "host"; + status = "okay"; +}; + &usdhc2 { assigned-clocks = <&clk IMX8MP_CLK_USDHC2>; assigned-clock-rates = <400000000>;
@@ -232,6 +247,12 @@ >; }; + pinctrl_usb1_vbus: usb1grp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO14__USB2_OTG_PWR 0x19 + >; + }; + pinctrl_usdhc2: usdhc2grp { fsl,pins = < MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190
Signature · 1 line
2.7.4