Add retimer interfaces support for Intel MAX 10 BMC
Subsystems (5)
Xu Yilun
maintainercover Add retimer interfaces support for Intel MAX 10 BMC
I resend this patchset to loop in networking developers for comments. This is the previous thread. I'll fix other comments when I have a v2.
https://lore.kernel.org/lkml/X%[email protected]/
The patchset is for the retimers connected to Intel MAX 10 BMC on Intel PAC (Programmable Acceleration Card) N3000 Card. The network part of the N3000 card is like the following:
+----------------------------------------+
| FPGA |
+----+ +-------+ +-----------+ +----------+ +-----------+ +----------+
|QSFP|---|retimer|---|Line Side |--|User logic|--|Host Side |---|XL710 |
+----+ +-------+ |Ether Group| | | |Ether Group| |Ethernet |
|(PHY + MAC)| |wiring & | |(MAC + PHY)| |Controller|
+-----------+ |offloading| +-----------+ +----------+
| +----------+ |
| |
+----------------------------------------+I had sent some RFC patches to expose the Line Side Ether Group + retimer + QSFP as a netdev, and got some comments from netdev Maintainers.
https://lore.kernel.org/netdev/[email protected]/
The blocking issues I have is that physically the QSFP & retimer is managed by the BMC and host could only get the retimer link states. This is not enough to support some necessary netdev ops. E.g. host cannot realize the type/speed of the SFP by "ethtool -m", then users could not configure the various layers accordingly.
This means the existing net tool can not work with it, so this patch just expose the link states as custom sysfs attrs.
This patchset supports the ethernet retimers (C827) for the Intel PAC (Programmable Acceleration Card) N3000, which is a FPGA based Smart NIC.
The 2 retimer chips connect to the Intel MAX 10 BMC on the card. They are managed by the BMC firmware. Host could query their link states and firmware version information via retimer interfaces (Shared registers) on the BMC. The driver creates sysfs interfaces for users to query these information.
The Intel OPAE (Open Programmable Acceleration Engine) lib provides tools to read these attributes.
This is the source of the OPAE lib.
https://github.com/OPAE/opae-sdk/
Generally it facilitate the development on all the DFL (Device Feature List) based FPGA Cards, including the management of static region & dynamic region reprogramming, accelerators accessing and the board specific peripherals.
Xu Yilun (2):
mfd: intel-m10-bmc: specify the retimer sub devices
misc: add support for retimers interfaces on Intel MAX 10 BMC
.../ABI/testing/sysfs-driver-intel-m10-bmc-retimer | 32 +++++ drivers/mfd/intel-m10-bmc.c | 19 ++- drivers/misc/Kconfig | 10 ++ drivers/misc/Makefile | 1 + drivers/misc/intel-m10-bmc-retimer.c | 158 +++++++++++++++++++++ include/linux/mfd/intel-m10-bmc.h | 7 + 6 files changed, 226 insertions(+), 1 deletion(-) create mode 100644 Documentation/ABI/testing/sysfs-driver-intel-m10-bmc-retimer create mode 100644 drivers/misc/intel-m10-bmc-retimer.c
Signature · 1 line
2.7.4
Xu Yilun
maintainerPATCH RESEND 1/2 mfd: intel-m10-bmc: specify the retimer sub devices
The patch specifies the 2 retimer sub devices and their resources in the parent driver's mfd_cell. It also adds the register definition of the retimer sub devices.
There are 2 ethernet retimer chips (C827) connected to the Intel MAX 10 BMC. They are managed by the BMC firmware, and host could query them via retimer interfaces (shared registers) on the BMC. The 2 retimers have identical register interfaces in different register addresses or fields, so it is better we define 2 retimer devices and handle them with the same driver.
--- drivers/mfd/intel-m10-bmc.c | 19 ++++++++++++++++++- include/linux/mfd/intel-m10-bmc.h | 7 +++++++ 2 files changed, 25 insertions(+), 1 deletion(-)
drivers/mfd/intel-m10-bmc.c +18 -1
@@ -17,9 +17,26 @@ enum m10bmc_type { M10_N3000, }; +static struct resource retimer0_resources[] = { + {M10BMC_PKVL_A_VER ,M10BMC_PKVL_A_VER ,"version" ,IORESOURCE_REG , }, +}; + +static struct resource retimer1_resources[] = { + {M10BMC_PKVL_B_VER ,M10BMC_PKVL_B_VER ,"version" ,IORESOURCE_REG , }, +}; +static struct mfd_cell m10bmc_pacn3000_subdevs[] = { { .name ="n3000bmc-hwmon" }, - { .name ="n3000bmc-retimer" }, + { + .name ="n3000bmc-retimer" , + .num_resources =ARRAY_SIZE (retimer0_resources), + .resources = retimer0_resources, + }, + { + .name ="n3000bmc-retimer" , + .num_resources =ARRAY_SIZE (retimer1_resources), + .resources = retimer1_resources, + }, { .name ="n3000bmc-secure" }, };
include/linux/mfd/intel-m10-bmc.h +7 -0
@@ -21,6 +21,13 @@#define M10BMC_VER_PCB_INFO_MSK GENMASK(31, 24)#define M10BMC_VER_LEGACY_INVALID 0xffffffff +/* Retimer related registers, in system register region */ +#define M10BMC_PKVL_LSTATUS 0x164 +#define M10BMC_PKVL_A_VER 0x254 +#define M10BMC_PKVL_B_VER 0x258 +#define M10BMC_PKVL_SERDES_VER GENMASK(15, 0) +#define M10BMC_PKVL_SBUS_VER GENMASK(31, 16) +/** * struct intel_m10bmc - Intel MAX 10 BMC parent driver data structure * @dev: this device
Signature · 1 line
2.7.4
Xu Yilun
maintainerPATCH RESEND 2/2 misc: add support for retimers interfaces on Intel MAX 10 BMC
In reply to Xu YilunThis driver supports the ethernet retimers (C827) for the Intel PAC (Programmable Acceleration Card) N3000, which is a FPGA based Smart NIC.
C827 is an Intel(R) Ethernet serdes transceiver chip that supports up to 100G transfer. On Intel PAC N3000 there are 2 C827 chips managed by the Intel MAX 10 BMC firmware. They are configured in 4 ports 10G/25G retimer mode. Host could query their link states and firmware version information via retimer interfaces (Shared registers) on Intel MAX 10 BMC. The driver creates sysfs interfaces for users to query these information.
--- .../ABI/testing/sysfs-driver-intel-m10-bmc-retimer | 32 +++++ drivers/misc/Kconfig | 10 ++ drivers/misc/Makefile | 1 + drivers/misc/intel-m10-bmc-retimer.c | 158 +++++++++++++++++++++ 4 files changed, 201 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-driver-intel-m10-bmc-retimer create mode 100644 drivers/misc/intel-m10-bmc-retimer.c
Documentation/ABI/testing/sysfs-driver-intel-m10-bmc-retimer new file +32 -0
@@ -0,0 +1,32 @@ +What: /sys/bus/platform/devices/n3000bmc-retimer.*.auto/tag +Date: Jan 2021 +KernelVersion: 5.12 +Contact: Xu Yilun <[email protected]> +Description: Read only. Returns the tag of the retimer chip. Now there are 2 + retimer chips on Intel PAC N3000, they are tagged as + 'retimer_A' and 'retimer_B'. + Format: "retimer_%c". + +What: /sys/bus/platform/devices/n3000bmc-retimer.*.auto/sbus_version +Date: Jan 2021 +KernelVersion: 5.12 +Contact: Xu Yilun <[email protected]> +Description: Read only. Returns the Transceiver bus firmware version of + the retimer chip. + Format: "0x%04x". + +What: /sys/bus/platform/devices/n3000bmc-retimer.*.auto/serdes_version +Date: Jan 2021 +KernelVersion: 5.12 +Contact: Xu Yilun <[email protected]> +Description: Read only. Returns the SERDES firmware version of the retimer + chip. + Format: "0x%04x". + +What: /sys/bus/platform/devices/n3000bmc-retimer.*.auto/link_statusX +Date: Jan 2021 +KernelVersion: 5.12 +Contact: Xu Yilun <[email protected]> +Description: Read only. Returns the status of each line side link. "1" for + link up, "0" for link down. + Format: "%u".
drivers/misc/Kconfig +10 -0
@@ -466,6 +466,16 @@ config HISI_HIKEY_USB switching between the dual-role USB-C port and the USB-A host ports using only one USB controller. +config INTEL_M10_BMC_RETIMER + tristate "Intel(R) MAX 10 BMC ethernet retimer interface support" + depends on MFD_INTEL_M10_BMC + help + This driver supports the ethernet retimer (C827) on Intel(R) MAX 10 + BMC, which is used by Intel PAC N3000 FPGA based Smart NIC. + + To compile this driver as a module, choose M here: the module will + be called intel-m10-bmc-retimer. + source "drivers/misc/c2port/Kconfig" source "drivers/misc/eeprom/Kconfig" source "drivers/misc/cb710/Kconfig"
drivers/misc/Makefile +1 -0
@@ -57,3 +57,4 @@ obj-$(CONFIG_HABANA_AI) += habanalabs/ obj-$(CONFIG_UACCE) += uacce/ obj-$(CONFIG_XILINX_SDFEC) += xilinx_sdfec.o obj-$(CONFIG_HISI_HIKEY_USB) += hisi_hikey_usb.o +obj-$(CONFIG_INTEL_M10_BMC_RETIMER) += intel-m10-bmc-retimer.o
drivers/misc/intel-m10-bmc-retimer.c new file +158 -0
158 lines not on this page · raw message
Signature · 1 line
2.7.4
Greg KH
maintainerRe: [RESEND PATCH 2/2] misc: add support for retimers interfaces on Intel MAX 10 BMC
Quoted 10 lines · Xu Yilun
This driver supports the ethernet retimers (C827) for the Intel PAC (Programmable Acceleration Card) N3000, which is a FPGA based Smart NIC.
C827 is an Intel(R) Ethernet serdes transceiver chip that supports up to 100G transfer. On Intel PAC N3000 there are 2 C827 chips managed by the Intel MAX 10 BMC firmware. They are configured in 4 ports 10G/25G retimer mode. Host could query their link states and firmware version information via retimer interfaces (Shared registers) on Intel MAX 10 BMC. The driver creates sysfs interfaces for users to query these information.
Networking people, please look at this sysfs file:
Documentation/ABI/testing/sysfs-driver-intel-m10-bmc-retimer line 32
Quoted 7 lines
Documentation/ABI/testing/sysfs-driver-intel-m10-bmc-retimer new file +7
-0+What: /sys/bus/platform/devices/n3000bmc-retimer.*.auto/link_statusX +Date: Jan 2021 +KernelVersion: 5.12 +Contact: Xu Yilun <[email protected]> +Description: Read only. Returns the status of each line side link. "1" for + link up, "0" for link down. + Format: "%u".
as I need your approval to add it because it is not the "normal" way for link status to be exported to userspace.
One code issue:
Quoted 14 lines
drivers/misc/intel-m10-bmc-retimer.c new file +14
-0+#define to_link_attr (dev_attr) \ + container_of(dev_attr, struct link_attr, attr) + +static ssize_t +link_status_show (struct device *dev,struct device_attribute *attr,char *buf) +{ +struct m10bmc_retimer *retimer =dev_get_drvdata (dev); +struct link_attr *lattr =to_link_attr (attr); +unsigned int val; +int ret; + + ret =m10bmc_sys_read (retimer->m10bmc,M10BMC_PKVL_LSTATUS , &val); +if (ret) +return ret;
drivers/misc/intel-m10-bmc-retimer.c line 92
Quoted 10 lines
drivers/misc/intel-m10-bmc-retimer.c new file +10
-0+ +return sysfs_emit (buf,"%u\n" , + !!(val &BIT ((retimer->id <<2 ) + lattr->index))); +} + +#define link_status_attr (_index) \ + static struct link_attr link_attr_status##_index = \ + { .attr = __ATTR(link_status##_index, 0444, \ + link_status_show, NULL), \ + .index = (_index) }
Why is this a "raw" attribute and not a device attribute?
Please just use a normal DEVICE_ATTR_RO() macro to make it simpler and easier to understand over time, what you are doing here. I can't determine what is happening with this code now...
thanks,
greg k-h
Re: [RESEND PATCH 2/2] misc: add support for retimers interfaces on Intel MAX 10 BMC
Quoted 14 lines · Greg KH
Quoted 10 lines · Xu Yilun
This driver supports the ethernet retimers (C827) for the Intel PAC (Programmable Acceleration Card) N3000, which is a FPGA based Smart NIC.
C827 is an Intel(R) Ethernet serdes transceiver chip that supports up to 100G transfer. On Intel PAC N3000 there are 2 C827 chips managed by the Intel MAX 10 BMC firmware. They are configured in 4 ports 10G/25G retimer mode. Host could query their link states and firmware version information via retimer interfaces (Shared registers) on Intel MAX 10 BMC. The driver creates sysfs interfaces for users to query these information.
Networking people, please look at this sysfs file:
Quoted 10 lines
Documentation/ABI/testing/sysfs-driver-intel-m10-bmc-retimer line 32
Quoted 7 lines
Documentation/ABI/testing/sysfs-driver-intel-m10-bmc-retimer new file +7
-0+What: /sys/bus/platform/devices/n3000bmc-retimer.*.auto/link_statusX +Date: Jan 2021 +KernelVersion: 5.12 +Contact: Xu Yilun <[email protected]> +Description: Read only. Returns the status of each line side link. "1" for + link up, "0" for link down. + Format: "%u".as I need your approval to add it because it is not the "normal" way for link status to be exported to userspace.
Hi Greg
Correct, this is not going to be acceptable.
The whole architecture needs to cleanly fit into the phylink model for controlling the SFP and the retimer.
I'm guessing Intel needs to rewrite portions of the BMC firmware to either transparently pass through access to the SFP socket and the retimer for phylink and a C827 specific driver, or add a high level API which a MAC driver can use, and completely hide away these PHY details from Linux, which is what many of the Intel Ethernet drivers do.
Andrew
Xu Yilun
maintainerRe: [RESEND PATCH 2/2] misc: add support for retimers interfaces on Intel MAX 10 BMC
Quoted 33 lines · Andrew Lunn
Quoted 14 lines · Greg KH
Quoted 10 lines · Xu Yilun
This driver supports the ethernet retimers (C827) for the Intel PAC (Programmable Acceleration Card) N3000, which is a FPGA based Smart NIC.
C827 is an Intel(R) Ethernet serdes transceiver chip that supports up to 100G transfer. On Intel PAC N3000 there are 2 C827 chips managed by the Intel MAX 10 BMC firmware. They are configured in 4 ports 10G/25G retimer mode. Host could query their link states and firmware version information via retimer interfaces (Shared registers) on Intel MAX 10 BMC. The driver creates sysfs interfaces for users to query these information.
Networking people, please look at this sysfs file:
Quoted 10 lines
Documentation/ABI/testing/sysfs-driver-intel-m10-bmc-retimer line 32
Quoted 7 lines
Documentation/ABI/testing/sysfs-driver-intel-m10-bmc-retimer new file +7
-0+What: /sys/bus/platform/devices/n3000bmc-retimer.*.auto/link_statusX +Date: Jan 2021 +KernelVersion: 5.12 +Contact: Xu Yilun <[email protected]> +Description: Read only. Returns the status of each line side link. "1" for + link up, "0" for link down. + Format: "%u".as I need your approval to add it because it is not the "normal" way for link status to be exported to userspace.
Hi Greg
Correct, this is not going to be acceptable.
The whole architecture needs to cleanly fit into the phylink model for controlling the SFP and the retimer.
Quoted 6 lines
I'm guessing Intel needs to rewrite portions of the BMC firmware to either transparently pass through access to the SFP socket and the retimer for phylink and a C827 specific driver, or add a high level API which a MAC driver can use, and completely hide away these PHY details from Linux, which is what many of the Intel Ethernet drivers do.
Got it, Thanks for your explanation.
Yilun
Xu Yilun
maintainerRe: [RESEND PATCH 2/2] misc: add support for retimers interfaces on Intel MAX 10 BMC
In reply to Greg KHQuoted 45 lines · Greg KH
Quoted 10 lines · Xu Yilun
This driver supports the ethernet retimers (C827) for the Intel PAC (Programmable Acceleration Card) N3000, which is a FPGA based Smart NIC.
C827 is an Intel(R) Ethernet serdes transceiver chip that supports up to 100G transfer. On Intel PAC N3000 there are 2 C827 chips managed by the Intel MAX 10 BMC firmware. They are configured in 4 ports 10G/25G retimer mode. Host could query their link states and firmware version information via retimer interfaces (Shared registers) on Intel MAX 10 BMC. The driver creates sysfs interfaces for users to query these information.
Networking people, please look at this sysfs file:
Documentation/ABI/testing/sysfs-driver-intel-m10-bmc-retimer line 32
Quoted 7 lines
Documentation/ABI/testing/sysfs-driver-intel-m10-bmc-retimer new file +7
-0+What: /sys/bus/platform/devices/n3000bmc-retimer.*.auto/link_statusX +Date: Jan 2021 +KernelVersion: 5.12 +Contact: Xu Yilun <[email protected]> +Description: Read only. Returns the status of each line side link. "1" for + link up, "0" for link down. + Format: "%u".as I need your approval to add it because it is not the "normal" way for link status to be exported to userspace.
One code issue:
Quoted 18 lines
drivers/misc/intel-m10-bmc-retimer.c new file +18
-0+#define to_link_attr (dev_attr) \ + container_of(dev_attr, struct link_attr, attr) + +static ssize_t +link_status_show (struct device *dev,struct device_attribute *attr,char *buf) +{ +struct m10bmc_retimer *retimer =dev_get_drvdata (dev); +struct link_attr *lattr =to_link_attr (attr); +unsigned int val; +int ret; + + ret =m10bmc_sys_read (retimer->m10bmc,M10BMC_PKVL_LSTATUS , &val); +if (ret) +return ret; + +return sysfs_emit (buf,"%u\n" , + !!(val &BIT ((retimer->id <<2 ) + lattr->index))); +}
Quoted 8 lines
drivers/misc/intel-m10-bmc-retimer.c line 92
Quoted 6 lines
drivers/misc/intel-m10-bmc-retimer.c new file +6
-0+ +#define link_status_attr (_index) \ + static struct link_attr link_attr_status##_index = \ + { .attr = __ATTR(link_status##_index, 0444, \ + link_status_show, NULL), \ + .index = (_index) }Why is this a "raw" attribute and not a device attribute?
It is actually a device_attribute. The device_attribute is embedded in link_attr, like:
struct link_attr {
struct device_attribute attr;
u32 index;};
An index for the link is appended along with the device_attribute, so we could identify which link is being queried on link_status_show(). There are 4 links and this is to avoid duplicated code like link_status_1_show(), link_status_2_show() ...
Quoted 2 lines
Please just use a normal
DEVICE_ATTR_RO()macro to make it simpler and
DEVICE_ATTR_RO() is to define a standalone device_attribute variable, but here we are initializing a field in struct link_attr.
Thanks,
Yilun
Quoted 6 lines
easier to understand over time, what you are doing here. I can't determine what is happening with this code now...
thanks,
greg k-h
Greg KH
maintainerRe: [RESEND PATCH 2/2] misc: add support for retimers interfaces on Intel MAX 10 BMC
Quoted 61 lines · Xu Yilun
Quoted 45 lines · Greg KH
Quoted 10 lines · Xu Yilun
This driver supports the ethernet retimers (C827) for the Intel PAC (Programmable Acceleration Card) N3000, which is a FPGA based Smart NIC.
C827 is an Intel(R) Ethernet serdes transceiver chip that supports up to 100G transfer. On Intel PAC N3000 there are 2 C827 chips managed by the Intel MAX 10 BMC firmware. They are configured in 4 ports 10G/25G retimer mode. Host could query their link states and firmware version information via retimer interfaces (Shared registers) on Intel MAX 10 BMC. The driver creates sysfs interfaces for users to query these information.
Networking people, please look at this sysfs file:
Documentation/ABI/testing/sysfs-driver-intel-m10-bmc-retimer line 32
Quoted 7 lines
Documentation/ABI/testing/sysfs-driver-intel-m10-bmc-retimer new file +7
-0+What: /sys/bus/platform/devices/n3000bmc-retimer.*.auto/link_statusX +Date: Jan 2021 +KernelVersion: 5.12 +Contact: Xu Yilun <[email protected]> +Description: Read only. Returns the status of each line side link. "1" for + link up, "0" for link down. + Format: "%u".as I need your approval to add it because it is not the "normal" way for link status to be exported to userspace.
One code issue:
Quoted 18 lines
drivers/misc/intel-m10-bmc-retimer.c new file +18
-0+#define to_link_attr (dev_attr) \ + container_of(dev_attr, struct link_attr, attr) + +static ssize_t +link_status_show (struct device *dev,struct device_attribute *attr,char *buf) +{ +struct m10bmc_retimer *retimer =dev_get_drvdata (dev); +struct link_attr *lattr =to_link_attr (attr); +unsigned int val; +int ret; + + ret =m10bmc_sys_read (retimer->m10bmc,M10BMC_PKVL_LSTATUS , &val); +if (ret) +return ret; + +return sysfs_emit (buf,"%u\n" , + !!(val &BIT ((retimer->id <<2 ) + lattr->index))); +}Quoted 8 lines
drivers/misc/intel-m10-bmc-retimer.c line 92
Quoted 6 lines
drivers/misc/intel-m10-bmc-retimer.c new file +6
-0+ +#define link_status_attr (_index) \ + static struct link_attr link_attr_status##_index = \ + { .attr = __ATTR(link_status##_index, 0444, \ + link_status_show, NULL), \ + .index = (_index) }Why is this a "raw" attribute and not a device attribute?
It is actually a
device_attribute. Thedevice_attributeis embedded inlink_attr, like:struct link_attr { struct device_attribute attr; u32 index;
Quoted 6 lines
};
An index for the link is appended along with the
device_attribute, so we could identify which link is being queried onlink_status_show(). There are 4 links and this is to avoid duplicated code likelink_status_1_show(),link_status_2_show()...
Duplicated code is better to read than complex code :)
Quoted 4 lines
Quoted 1 line
Please just use a normal
DEVICE_ATTR_RO()macro to make it simpler and
DEVICE_ATTR_RO()is to define a standalonedevice_attributevariable, but here we are initializing a field in structlink_attr.
Then use the correct initialization macro that is given to you for that, do not roll your own.
greg k-h