Skip to contentSkip to conversation

arm64: dts: qcom: sm8750: Add UART15

PATCH Applied Aaron Kling 4 participants 4 messages Jun 5 – Jul 8

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 arm64: dts: qcom: sm8750: Add UART15

From: Teguh Sobirin <[email protected]>

Add uart15 node for the UART bus present on the sm8750 SoC.

---
arm64: dts: qcom: sm8750: Add UART15

---
 arch/arm64/boot/dts/qcom/sm8750.dtsi | 30 ++++++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)
arch/arm64/boot/dts/qcom/sm8750.dtsi +30 -0
index fafed417c66fc2..7591ebb7086f91 100644
@@ -1218,6 +1218,28 @@ &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>,
 
 				status = "disabled";
 			};
+
+			uart15: serial@89c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x0089c000 0x0 0x4000>;
+
+				interrupts = <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP2_S7_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core",
+						     "qup-config";
+
+				pinctrl-0 = <&qup_uart15_default>;
+				pinctrl-names = "default";
+
+				status = "disabled";
+			};
 		};
 
 		i2c_master_hub_0: geniqup@9c0000 {
@@ -4055,6 +4077,14 @@ qup_uart14_cts_rts: qup-uart14-cts-rts-state {
 				bias-pull-down;
 			};
 
+			qup_uart15_default: qup-uart15-default-state {
+				/* TX, RX */
+				pins = "gpio30", "gpio31";
+				function = "qup2_se7";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
 			sdc2_sleep: sdc2-sleep-state {
 				clk-pins {
 					pins = "sdc2_clk";

---
base-commit: 6e845bcb78c95af935094040bd4edc3c2b6dd784
change-id: 20260605-sm8750-uart15-e8b3e08ef73c

Best regards,

Signature · 1 line
Aaron Kling <[email protected]>
Reviewed-by on v1 1/1
#1 lore raw
Quoted 4 lines · On Fri, Jun 05, 2026 at 05:49:39PM -0500, Aaron Kling via B4 Relay wrote:

From: Teguh Sobirin <[email protected]>

Add uart15 node for the UART bus present on the sm8750 SoC.

Quoted 8 lines

---
arm64: dts: qcom: sm8750: Add UART15

---
 arch/arm64/boot/dts/qcom/sm8750.dtsi | 30 ++++++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)
Signature · 2 lines
With best wishes
Dmitry
maintainer Applied
#3 lore raw
In reply to Aaron Kling
Quoted 3 lines · Aaron Kling

Add uart15 node for the UART bus present on the sm8750 SoC.

Applied, thanks!

[1/1] arm64: dts: qcom: sm8750: Add UART15

      commit: 50c0854e2703b4e446f83680d7eb0dc0bd5bb34d

Best regards,

Signature · 1 line
Bjorn Andersson <[email protected]>