mtd: rawnand: qcom: update last code word register
PATCH v3 1/1 mtd: rawnand: qcom: update last code word register
From QPIC version 2.0 onwards new register got added to read last codeword. This change will update the same.
For first three code word READ_LOCATION_n register will be use.For last code word READ_LOCATION_LAST_CW_n register will be use.
---
[V3]
* Added else condition for last code word in update_rw_regs().
drivers/mtd/nand/raw/qcom_nandc.c | 84 ++++++++++++++++++++++++++++++++------- 1 file changed, 70 insertions(+), 14 deletions(-)
drivers/mtd/nand/raw/qcom_nandc.c +70 -14
@@ -48,6 +48,10 @@#define NAND_READ_LOCATION_1 0xf24#define NAND_READ_LOCATION_2 0xf28#define NAND_READ_LOCATION_3 0xf2c +#define NAND_READ_LOCATION_LAST_CW_0 0xf40 +#define NAND_READ_LOCATION_LAST_CW_1 0xf44 +#define NAND_READ_LOCATION_LAST_CW_2 0xf48 +#define NAND_READ_LOCATION_LAST_CW_3 0xf4c/* dummy register offsets, used by write_reg_dma */ #define NAND_DEV_CMD1_RESTORE 0xdead
@@ -187,6 +191,12 @@ nandc_set_reg(nandc, NAND_READ_LOCATION_##reg, \ ((size) << READ_LOCATION_SIZE) | \ ((is_last) << READ_LOCATION_LAST)) +#define nandc_set_read_loc_last (nandc, reg, offset, size, is_last) \ +nandc_set_reg(nandc, NAND_READ_LOCATION_LAST_CW_##reg, \ + ((offset) << READ_LOCATION_OFFSET) | \ + ((size) << READ_LOCATION_SIZE) | \ + ((is_last) << READ_LOCATION_LAST)) +/* * Returns the actual register address for all NAND_DEV_ registers * (i.e. NAND_DEV_CMD0, NAND_DEV_CMD1, NAND_DEV_CMD2 and NAND_DEV_CMD_VLD)
@@ -316,6 +326,10 @@ struct nandc_regs {__le32 read_location1;__le32 read_location2;__le32 read_location3; +__le32 read_location_last0; +__le32 read_location_last1; +__le32 read_location_last2; +__le32 read_location_last3;__le32 erased_cw_detect_cfg_clr;__le32 erased_cw_detect_cfg_set;
@@ -644,6 +658,14 @@ static __le32 *offset_to_nandc_reg(struct nandc_regs *regs, int offset)return ®s->read_location2;case NAND_READ_LOCATION_3 :return ®s->read_location3; +case NAND_READ_LOCATION_LAST_CW_0 : +return ®s->read_location_last0; +case NAND_READ_LOCATION_LAST_CW_1 : +return ®s->read_location_last1; +case NAND_READ_LOCATION_LAST_CW_2 : +return ®s->read_location_last2; +case NAND_READ_LOCATION_LAST_CW_3 : +return ®s->read_location_last3;default :return NULL ; }
@@ -719,9 +741,14 @@ static void update_rw_regs(struct qcom_nand_host *host, int num_cw, bool read)nandc_set_reg (nandc,NAND_READ_STATUS , host->clrreadstatus);nandc_set_reg (nandc,NAND_EXEC_CMD ,1 ); -if (read) -nandc_set_read_loc (nandc,0 ,0 , host->use_ecc ? - host->cw_data : host->cw_size,1 ); +if (read) { +if (nandc->props->qpic_v2) +nandc_set_read_loc_last (nandc,0 ,0 , host->use_ecc ? + host->cw_data : host->cw_size,1 ); +else +nandc_set_read_loc (nandc,0 ,0 , host->use_ecc ? + host->cw_data : host->cw_size,1 ); + } }/*
@@ -1096,9 +1123,13 @@ static void config_nand_page_read(struct qcom_nand_controller *nandc)static void config_nand_cw_read (struct qcom_nand_controller *nandc,bool use_ecc) { -if (nandc->props->is_bam) +if (nandc->props->is_bam) { +if (nandc->props->qpic_v2) +write_reg_dma (nandc,NAND_READ_LOCATION_LAST_CW_0 , +1 ,NAND_BAM_NEXT_SGL );write_reg_dma (nandc,NAND_READ_LOCATION_0 ,4 ,NAND_BAM_NEXT_SGL ); + }write_reg_dma (nandc,NAND_FLASH_CMD ,1 ,NAND_BAM_NEXT_SGL );write_reg_dma (nandc,NAND_EXEC_CMD ,1 ,NAND_BAM_NEXT_SGL );
@@ -1633,16 +1664,28 @@ qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip, }if (nandc->props->is_bam) { -nandc_set_read_loc (nandc,0 , read_loc, data_size1,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,0 , read_loc, data_size1,0 ); +else +nandc_set_read_loc (nandc,0 , read_loc, data_size1,0 ); read_loc += data_size1; -nandc_set_read_loc (nandc,1 , read_loc, oob_size1,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,1 , read_loc, oob_size1,0 ); +else +nandc_set_read_loc (nandc,1 , read_loc, oob_size1,0 ); read_loc += oob_size1; -nandc_set_read_loc (nandc,2 , read_loc, data_size2,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,2 , read_loc, data_size2,0 ); +else +nandc_set_read_loc (nandc,2 , read_loc, data_size2,0 ); read_loc += data_size2; -nandc_set_read_loc (nandc,3 , read_loc, oob_size2,1 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,3 , read_loc, oob_size2,0 ); +else +nandc_set_read_loc (nandc,3 , read_loc, oob_size2,1 ); }config_nand_cw_read (nandc, false);
@@ -1873,14 +1916,27 @@ static int read_page_ecc(struct qcom_nand_host *host, u8 *data_buf,if (nandc->props->is_bam) {if (data_buf && oob_buf) { -nandc_set_read_loc (nandc,0 ,0 , data_size,0 ); -nandc_set_read_loc (nandc,1 , data_size, - oob_size,1 ); +if (nandc->props->qpic_v2 && i == (ecc->steps -1 )) { +nandc_set_read_loc_last (nandc,0 ,0 , data_size,0 ); +nandc_set_read_loc_last (nandc,1 , data_size, + oob_size,1 ); + }else { +nandc_set_read_loc (nandc,0 ,0 , data_size,0 ); +nandc_set_read_loc (nandc,1 , data_size, + oob_size,1 ); + } }else if (data_buf) { -nandc_set_read_loc (nandc,0 ,0 , data_size,1 ); +if (nandc->props->qpic_v2 && i == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,0 ,0 , data_size,1 ); +else +nandc_set_read_loc (nandc,0 ,0 , data_size,1 ); }else { -nandc_set_read_loc (nandc,0 , data_size, - oob_size,1 ); +if (nandc->props->qpic_v2 && i == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,0 , data_size, + oob_size,1 ); +else +nandc_set_read_loc (nandc,0 , data_size, + oob_size,1 ); } }
Signature · 1 line
2.7.4
Miquel Raynal
maintainerHello,
Md Sadre Alam <[email protected]> wrote on Sun, 10 Jan 2021 09:31:45 +0530:
Quoted 1 line
From QPIC version 2.0 onwards new register got added to
a
Quoted 1 line
read last codeword. This change will update the same.
the? ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Please reword this sentence.
Quoted 3 lines
For first three code word
READ_LOCATION_nregister will be use.For last code wordREAD_LOCATION_LAST_CW_nregister will be use.
"For the first three codewords, READ_LOCATION_n registers will be used. The last codeword register will be accessed through READ_LOCATION_LAST_CW_n."
Also, please specify what these registers store.
Quoted 1 line
Signed-off-by Md Sadre Alam <[email protected]>
Could someone please test this patch?
Quoted 94 lines
---
[V3]
* Added else condition for last code word inupdate_rw_regs().drivers/mtd/nand/raw/qcom_nandc.c | 84 ++++++++++++++++++++++++++++++++------- 1 file changed, 70 insertions(+), 14 deletions(-)drivers/mtd/nand/raw/qcom_nandc.c +35
-4@@ -48,6 +48,10 @@#define NAND_READ_LOCATION_1 0xf24#define NAND_READ_LOCATION_2 0xf28#define NAND_READ_LOCATION_3 0xf2c +#define NAND_READ_LOCATION_LAST_CW_0 0xf40 +#define NAND_READ_LOCATION_LAST_CW_1 0xf44 +#define NAND_READ_LOCATION_LAST_CW_2 0xf48 +#define NAND_READ_LOCATION_LAST_CW_3 0xf4c/* dummy register offsets, used by write_reg_dma */ #define NAND_DEV_CMD1_RESTORE 0xdead@@ -187,6 +191,12 @@ nandc_set_reg(nandc, NAND_READ_LOCATION_##reg, \ ((size) << READ_LOCATION_SIZE) | \ ((is_last) << READ_LOCATION_LAST)) +#define nandc_set_read_loc_last (nandc, reg, offset, size, is_last) \ +nandc_set_reg(nandc, NAND_READ_LOCATION_LAST_CW_##reg, \ + ((offset) << READ_LOCATION_OFFSET) | \ + ((size) << READ_LOCATION_SIZE) | \ + ((is_last) << READ_LOCATION_LAST)) +/* * Returns the actual register address for all NAND_DEV_ registers * (i.e. NAND_DEV_CMD0, NAND_DEV_CMD1, NAND_DEV_CMD2 and NAND_DEV_CMD_VLD) @@ -316,6 +326,10 @@ struct nandc_regs {__le32 read_location1;__le32 read_location2;__le32 read_location3; +__le32 read_location_last0; +__le32 read_location_last1; +__le32 read_location_last2; +__le32 read_location_last3;__le32 erased_cw_detect_cfg_clr;__le32 erased_cw_detect_cfg_set;@@ -644,6 +658,14 @@ static __le32 *offset_to_nandc_reg(struct nandc_regs *regs, int offset)return ®s->read_location2;case NAND_READ_LOCATION_3 :return ®s->read_location3; +case NAND_READ_LOCATION_LAST_CW_0 : +return ®s->read_location_last0; +case NAND_READ_LOCATION_LAST_CW_1 : +return ®s->read_location_last1; +case NAND_READ_LOCATION_LAST_CW_2 : +return ®s->read_location_last2; +case NAND_READ_LOCATION_LAST_CW_3 : +return ®s->read_location_last3;default :return NULL ; }@@ -719,9 +741,14 @@ static void update_rw_regs(struct qcom_nand_host *host, int num_cw, bool read)nandc_set_reg (nandc,NAND_READ_STATUS , host->clrreadstatus);nandc_set_reg (nandc,NAND_EXEC_CMD ,1 ); -if (read) -nandc_set_read_loc (nandc,0 ,0 , host->use_ecc ? - host->cw_data : host->cw_size,1 ); +if (read) { +if (nandc->props->qpic_v2) +nandc_set_read_loc_last (nandc,0 ,0 , host->use_ecc ? + host->cw_data : host->cw_size,1 ); +else +nandc_set_read_loc (nandc,0 ,0 , host->use_ecc ? + host->cw_data : host->cw_size,1 ); + } }/* @@ -1096,9 +1123,13 @@ static void config_nand_page_read(struct qcom_nand_controller *nandc)static void config_nand_cw_read (struct qcom_nand_controller *nandc,bool use_ecc) { -if (nandc->props->is_bam) +if (nandc->props->is_bam) { +if (nandc->props->qpic_v2) +write_reg_dma (nandc,NAND_READ_LOCATION_LAST_CW_0 , +1 ,NAND_BAM_NEXT_SGL );write_reg_dma (nandc,NAND_READ_LOCATION_0 ,4 ,NAND_BAM_NEXT_SGL ); + }write_reg_dma (nandc,NAND_FLASH_CMD ,1 ,NAND_BAM_NEXT_SGL );write_reg_dma (nandc,NAND_EXEC_CMD ,1 ,NAND_BAM_NEXT_SGL );
drivers/mtd/nand/raw/qcom_nandc.c qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip, · line 1670
Quoted 8 lines
drivers/mtd/nand/raw/qcom_nandc.c +4
-1@@ -1633,16 +1664,28 @@ qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip, }if (nandc->props->is_bam) { -nandc_set_read_loc (nandc,0 , read_loc, data_size1,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,0 , read_loc, data_size1,0 ); +else +nandc_set_read_loc (nandc,0 , read_loc, data_size1,0 );
You repeat many times this logic, a helper to avoid this extra indentation level with the if/else block is needed.
Quoted 12 lines
drivers/mtd/nand/raw/qcom_nandc.c +6
-2read_loc += data_size1; -nandc_set_read_loc (nandc,1 , read_loc, oob_size1,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,1 , read_loc, oob_size1,0 ); +else +nandc_set_read_loc (nandc,1 , read_loc, oob_size1,0 ); read_loc += oob_size1; -nandc_set_read_loc (nandc,2 , read_loc, data_size2,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,2 , read_loc, data_size2,0 );
drivers/mtd/nand/raw/qcom_nandc.c qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip, · line 1689
Quoted 10 lines
drivers/mtd/nand/raw/qcom_nandc.c +6
-1+else +nandc_set_read_loc (nandc,2 , read_loc, data_size2,0 ); read_loc += data_size2; -nandc_set_read_loc (nandc,3 , read_loc, oob_size2,1 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,3 , read_loc, oob_size2,0 ); +else +nandc_set_read_loc (nandc,3 , read_loc, oob_size2,1 ); }
Thanks,
Miquèl
Quoted 22 lines · Miquel Raynal
Hello,
Md Sadre Alam <[email protected]> wrote on Sun, 10 Jan 2021 09:31:45 +0530:
Quoted 1 line
From QPIC version 2.0 onwards new register got added to
a
Quoted 1 line
read last codeword. This change will update the same.
the? ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Please reword this sentence.Quoted 3 lines
For first three code word
READ_LOCATION_nregister will be use.For last code wordREAD_LOCATION_LAST_CW_nregister will be use."For the first three codewords,
READ_LOCATION_nregisters will be used. The last codeword register will be accessed throughREAD_LOCATION_LAST_CW_n."
Quoted 6 lines
Also, please specify what these registers store.
Quoted 1 line
Signed-off-by Md Sadre Alam <[email protected]>Could someone please test this patch?
This is on my TODO list. Will get back to it once I'm back from holidays or sooner if I find some time in the middle.
Thanks,
Mani
Quoted 122 lines
Quoted 94 lines
---
[V3]
* Added else condition for last code word inupdate_rw_regs().drivers/mtd/nand/raw/qcom_nandc.c | 84 ++++++++++++++++++++++++++++++++------- 1 file changed, 70 insertions(+), 14 deletions(-)drivers/mtd/nand/raw/qcom_nandc.c +35
-4@@ -48,6 +48,10 @@#define NAND_READ_LOCATION_1 0xf24#define NAND_READ_LOCATION_2 0xf28#define NAND_READ_LOCATION_3 0xf2c +#define NAND_READ_LOCATION_LAST_CW_0 0xf40 +#define NAND_READ_LOCATION_LAST_CW_1 0xf44 +#define NAND_READ_LOCATION_LAST_CW_2 0xf48 +#define NAND_READ_LOCATION_LAST_CW_3 0xf4c/* dummy register offsets, used by write_reg_dma */ #define NAND_DEV_CMD1_RESTORE 0xdead@@ -187,6 +191,12 @@ nandc_set_reg(nandc, NAND_READ_LOCATION_##reg, \ ((size) << READ_LOCATION_SIZE) | \ ((is_last) << READ_LOCATION_LAST)) +#define nandc_set_read_loc_last (nandc, reg, offset, size, is_last) \ +nandc_set_reg(nandc, NAND_READ_LOCATION_LAST_CW_##reg, \ + ((offset) << READ_LOCATION_OFFSET) | \ + ((size) << READ_LOCATION_SIZE) | \ + ((is_last) << READ_LOCATION_LAST)) +/* * Returns the actual register address for all NAND_DEV_ registers * (i.e. NAND_DEV_CMD0, NAND_DEV_CMD1, NAND_DEV_CMD2 and NAND_DEV_CMD_VLD) @@ -316,6 +326,10 @@ struct nandc_regs {__le32 read_location1;__le32 read_location2;__le32 read_location3; +__le32 read_location_last0; +__le32 read_location_last1; +__le32 read_location_last2; +__le32 read_location_last3;__le32 erased_cw_detect_cfg_clr;__le32 erased_cw_detect_cfg_set;@@ -644,6 +658,14 @@ static __le32 *offset_to_nandc_reg(struct nandc_regs *regs, int offset)return ®s->read_location2;case NAND_READ_LOCATION_3 :return ®s->read_location3; +case NAND_READ_LOCATION_LAST_CW_0 : +return ®s->read_location_last0; +case NAND_READ_LOCATION_LAST_CW_1 : +return ®s->read_location_last1; +case NAND_READ_LOCATION_LAST_CW_2 : +return ®s->read_location_last2; +case NAND_READ_LOCATION_LAST_CW_3 : +return ®s->read_location_last3;default :return NULL ; }@@ -719,9 +741,14 @@ static void update_rw_regs(struct qcom_nand_host *host, int num_cw, bool read)nandc_set_reg (nandc,NAND_READ_STATUS , host->clrreadstatus);nandc_set_reg (nandc,NAND_EXEC_CMD ,1 ); -if (read) -nandc_set_read_loc (nandc,0 ,0 , host->use_ecc ? - host->cw_data : host->cw_size,1 ); +if (read) { +if (nandc->props->qpic_v2) +nandc_set_read_loc_last (nandc,0 ,0 , host->use_ecc ? + host->cw_data : host->cw_size,1 ); +else +nandc_set_read_loc (nandc,0 ,0 , host->use_ecc ? + host->cw_data : host->cw_size,1 ); + } }/* @@ -1096,9 +1123,13 @@ static void config_nand_page_read(struct qcom_nand_controller *nandc)static void config_nand_cw_read (struct qcom_nand_controller *nandc,bool use_ecc) { -if (nandc->props->is_bam) +if (nandc->props->is_bam) { +if (nandc->props->qpic_v2) +write_reg_dma (nandc,NAND_READ_LOCATION_LAST_CW_0 , +1 ,NAND_BAM_NEXT_SGL );write_reg_dma (nandc,NAND_READ_LOCATION_0 ,4 ,NAND_BAM_NEXT_SGL ); + }write_reg_dma (nandc,NAND_FLASH_CMD ,1 ,NAND_BAM_NEXT_SGL );write_reg_dma (nandc,NAND_EXEC_CMD ,1 ,NAND_BAM_NEXT_SGL );drivers/mtd/nand/raw/qcom_nandc.c qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip, · line 1670
Quoted 8 lines
drivers/mtd/nand/raw/qcom_nandc.c +4
-1@@ -1633,16 +1664,28 @@ qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip, }if (nandc->props->is_bam) { -nandc_set_read_loc (nandc,0 , read_loc, data_size1,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,0 , read_loc, data_size1,0 ); +else +nandc_set_read_loc (nandc,0 , read_loc, data_size1,0 );You repeat many times this logic, a helper to avoid this extra indentation level with the if/else block is needed.
Quoted 16 lines
drivers/mtd/nand/raw/qcom_nandc.c +8
-2read_loc += data_size1; -nandc_set_read_loc (nandc,1 , read_loc, oob_size1,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,1 , read_loc, oob_size1,0 ); +else +nandc_set_read_loc (nandc,1 , read_loc, oob_size1,0 ); read_loc += oob_size1; -nandc_set_read_loc (nandc,2 , read_loc, data_size2,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,2 , read_loc, data_size2,0 ); +else +nandc_set_read_loc (nandc,2 , read_loc, data_size2,0 ); read_loc += data_size2;
Quoted 9 lines
drivers/mtd/nand/raw/qcom_nandc.c qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip, · line 1689
Quoted 6 lines
drivers/mtd/nand/raw/qcom_nandc.c +4
-1-nandc_set_read_loc (nandc,3 , read_loc, oob_size2,1 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,3 , read_loc, oob_size2,0 ); +else +nandc_set_read_loc (nandc,3 , read_loc, oob_size2,1 ); }Thanks,
Miquèl
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Miquel Raynal
maintainerHi Manivannan,
Manivannan Sadhasivam <[email protected]> wrote on Thu, 14 Jan 2021 22:01:54 +0530:
Quoted 25 lines · Miquel Raynal
Quoted 24 lines
Hello,
Md Sadre Alam <[email protected]> wrote on Sun, 10 Jan 2021 09:31:45 +0530:
Quoted 1 line
From QPIC version 2.0 onwards new register got added to
a
Quoted 1 line
read last codeword. This change will update the same.
the? ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Please reword this sentence.Quoted 3 lines
For first three code word
READ_LOCATION_nregister will be use.For last code wordREAD_LOCATION_LAST_CW_nregister will be use."For the first three codewords,
READ_LOCATION_nregisters will be used. The last codeword register will be accessed throughREAD_LOCATION_LAST_CW_n."Also, please specify what these registers store.
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
Signed-off-by Md Sadre Alam <[email protected]>Could someone please test this patch?
This is on my TODO list. Will get back to it once I'm back from holidays or sooner if I find some time in the middle.
No hurry, I believe this patch still needs a little bit of effort before being ready for upstreaming.
Thanks,
Miquèl
Quoted 5 lines · Miquel Raynal
Hello,
Md Sadre Alam <[email protected]> wrote on Sun, 10 Jan 2021 09:31:45 +0530:
Quoted 8 lines
Quoted 1 line
From QPIC version 2.0 onwards new register got added to
a
Quoted 1 line
read last codeword. This change will update the same.
the? ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Please reword this sentence.
Fixed this in V4 patch.
Quoted 10 lines
Quoted 4 lines
For first three code word
READ_LOCATION_nregister will be use.For last code wordREAD_LOCATION_LAST_CW_nregister will be use."For the first three codewords,
READ_LOCATION_nregisters will be used. The last codeword register will be accessed throughREAD_LOCATION_LAST_CW_n."Also, please specify what these registers store.
The location register is mainly use for reading controller buffer via BAM mode. The bits of the register
"NAND_READ_LOCATION_LAST_CW_n, n=0..4"
as follow:
[9:0]-bits : (OFFSET) This bit defines the offset from the buffer base
address to be picked up for DMA.
[25:16]-bits: (SIZE) This bit of every register will define the size
of the chunk for DMA.
31-bit : (LAST) If this bit is set, the controller takes the
particular register to specify the last chunk
of data made available for DMA. This chunk is part
of the internal buffer of the controller.
Quoted 4 lines
Quoted 2 lines
Signed-off-by Md Sadre Alam <[email protected]>Could someone please test this patch?
I have tested this patch on IPQ5018 platform and its working fine.
Quoted 104 lines
Quoted 104 lines
---
[V3]
* Added else condition for last code word inupdate_rw_regs().drivers/mtd/nand/raw/qcom_nandc.c | 84 ++++++++++++++++++++++++++++++++------- 1 file changed, 70 insertions(+), 14 deletions(-)drivers/mtd/nand/raw/qcom_nandc.c +10
-0@@ -48,6 +48,10 @@#define NAND_READ_LOCATION_1 0xf24#define NAND_READ_LOCATION_2 0xf28#define NAND_READ_LOCATION_3 0xf2c +#define NAND_READ_LOCATION_LAST_CW_0 0xf40 +#define NAND_READ_LOCATION_LAST_CW_1 0xf44 +#define NAND_READ_LOCATION_LAST_CW_2 0xf48 +#define NAND_READ_LOCATION_LAST_CW_3 0xf4c/* dummy register offsets, used by write_reg_dma */ #define NAND_DEV_CMD1_RESTORE 0xdead@@ -187,6 +191,12 @@ nandc_set_reg(nandc, NAND_READ_LOCATION_##reg, \ ((size) << READ_LOCATION_SIZE) | \ ((is_last) << READ_LOCATION_LAST)) +#define nandc_set_read_loc_last (nandc, reg, offset, size, is_last) \ +nandc_set_reg(nandc, NAND_READ_LOCATION_LAST_CW_##reg, \ + ((offset) << READ_LOCATION_OFFSET) | \ + ((size) << READ_LOCATION_SIZE) | \ + ((is_last) << READ_LOCATION_LAST)) +/* * Returns the actual register address for all NAND_DEV_ registers * (i.e.
NAND_DEV_CMD0,NAND_DEV_CMD1,NAND_DEV_CMD2andNAND_DEV_CMD_VLD)drivers/mtd/nand/raw/qcom_nandc.c +12
-0@@ -316,6 +326,10 @@ struct nandc_regs {__le32 read_location1;__le32 read_location2;__le32 read_location3; +__le32 read_location_last0; +__le32 read_location_last1; +__le32 read_location_last2; +__le32 read_location_last3;__le32 erased_cw_detect_cfg_clr;__le32 erased_cw_detect_cfg_set;@@ -644,6 +658,14 @@ static __le32 *offset_to_nandc_reg(struct nandc_regs *regs, int offset)return ®s->read_location2;case NAND_READ_LOCATION_3 :return ®s->read_location3; +case NAND_READ_LOCATION_LAST_CW_0 : +return ®s->read_location_last0; +case NAND_READ_LOCATION_LAST_CW_1 : +return ®s->read_location_last1; +case NAND_READ_LOCATION_LAST_CW_2 : +return ®s->read_location_last2; +case NAND_READ_LOCATION_LAST_CW_3 : +return ®s->read_location_last3;default :return NULL ;drivers/mtd/nand/raw/qcom_nandc.c +8
-3}@@ -719,9 +741,14 @@ static void update_rw_regs(struct qcom_nand_host *host, int num_cw, bool read)nandc_set_reg (nandc,NAND_READ_STATUS , host->clrreadstatus);nandc_set_reg (nandc,NAND_EXEC_CMD ,1 ); -if (read) -nandc_set_read_loc (nandc,0 ,0 , host->use_ecc ? - host->cw_data : host->cw_size,1 ); +if (read) { +if (nandc->props->qpic_v2) +nandc_set_read_loc_last (nandc,0 ,0 , host->use_ecc ? + host->cw_data : host->cw_size,1 ); +else +nandc_set_read_loc (nandc,0 ,0 , host->use_ecc ? + host->cw_data : host->cw_size,1 ); + } }/*
drivers/mtd/nand/raw/qcom_nandc.c +5
-1@@ -1096,9 +1123,13 @@ static void config_nand_page_read(struct qcom_nand_controller *nandc)static void config_nand_cw_read (struct qcom_nand_controller *nandc,bool use_ecc) { -if (nandc->props->is_bam) +if (nandc->props->is_bam) { +if (nandc->props->qpic_v2) +write_reg_dma (nandc,NAND_READ_LOCATION_LAST_CW_0 , +1 ,NAND_BAM_NEXT_SGL );write_reg_dma (nandc,NAND_READ_LOCATION_0 ,4 ,NAND_BAM_NEXT_SGL ); + }write_reg_dma (nandc,NAND_FLASH_CMD ,1 ,NAND_BAM_NEXT_SGL );drivers/mtd/nand/raw/qcom_nandc.c +0
-0write_reg_dma (nandc,NAND_EXEC_CMD ,1 ,NAND_BAM_NEXT_SGL );@@ -1633,16 +1664,28 @@ qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip, }
Quoted 9 lines
drivers/mtd/nand/raw/qcom_nandc.c qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip, · line 1670
Quoted 6 lines
drivers/mtd/nand/raw/qcom_nandc.c +4
-1if (nandc->props->is_bam) { -nandc_set_read_loc (nandc,0 , read_loc, data_size1,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,0 , read_loc, data_size1,0 ); +else +nandc_set_read_loc (nandc,0 , read_loc, data_size1,0 );You repeat many times this logic, a helper to avoid this extra indentation level with the if/else block is needed.
Fixed this V4 patch.
Quoted 26 lines
Quoted 13 lines
drivers/mtd/nand/raw/qcom_nandc.c +6
-2read_loc += data_size1; -nandc_set_read_loc (nandc,1 , read_loc, oob_size1,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,1 , read_loc, oob_size1,0 ); +else +nandc_set_read_loc (nandc,1 , read_loc, oob_size1,0 ); read_loc += oob_size1; -nandc_set_read_loc (nandc,2 , read_loc, data_size2,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,2 , read_loc, data_size2,0 );drivers/mtd/nand/raw/qcom_nandc.c qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip, · line 1689
Quoted 10 lines
drivers/mtd/nand/raw/qcom_nandc.c +6
-1+else +nandc_set_read_loc (nandc,2 , read_loc, data_size2,0 ); read_loc += data_size2; -nandc_set_read_loc (nandc,3 , read_loc, oob_size2,1 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,3 , read_loc, oob_size2,0 ); +else +nandc_set_read_loc (nandc,3 , read_loc, oob_size2,1 ); }Thanks,
Miquèl
Miquel Raynal
maintainerHello,
[email protected] wrote on Fri, 29 Jan 2021 03:18:46 +0530:
Quoted 25 lines · Miquel Raynal
Quoted 5 lines
Hello,
Md Sadre Alam <[email protected]> wrote on Sun, 10 Jan 2021 09:31:45 +0530:
Quoted 8 lines
Quoted 1 line
From QPIC version 2.0 onwards new register got added to
a
Quoted 1 line
read last codeword. This change will update the same.
the? ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Please reword this sentence.Fixed this in V4 patch.
Quoted 9 lines
Quoted 4 lines
For first three code word
READ_LOCATION_nregister will be use.For last code wordREAD_LOCATION_LAST_CW_nregister will be use."For the first three codewords,
READ_LOCATION_nregisters will be used. The last codeword register will be accessed throughREAD_LOCATION_LAST_CW_n."
Quoted 5 lines
Quoted 1 line
Also, please specify what these registers store.
The location register is mainly use for reading controller
buffer via BAM mode. The bits of the register "NAND_READ_LOCATION_LAST_CW_n, n=0..4" as follow:
Perhaps what I do not understand is: when is this "last_cw" register more useful than the previous set?
Quoted 6 lines
[9:0]-bits : (OFFSET) This bit defines the offset from the buffer base address to be picked up for DMA. [25:16]-bits: (SIZE) This bit of every register will define the size of the chunk for DMA.
31-bit : (LAST) If this bit is set, the controller takes the particular register to specify the last chunk
of data made available for DMA. This chunk is part of the internal buffer of the controller.Quoted 1 line
Thanks,
Miquèl
Quoted 31 lines · Miquel Raynal
Hello,
[email protected] wrote on Fri, 29 Jan 2021 03:18:46 +0530:
Quoted 27 lines · Miquel Raynal
Quoted 5 lines
Hello,
Md Sadre Alam <[email protected]> wrote on Sun, 10 Jan 2021 09:31:45 +0530:
Quoted 8 lines
Quoted 1 line
From QPIC version 2.0 onwards new register got added to
a
Quoted 1 line
read last codeword. This change will update the same.
the? ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Please reword this sentence.Fixed this in V4 patch.
Quoted 10 lines
Quoted 4 lines
For first three code word
READ_LOCATION_nregister will be use.For last code wordREAD_LOCATION_LAST_CW_nregister will be use."For the first three codewords,
READ_LOCATION_nregisters will be used. The last codeword register will be accessed throughREAD_LOCATION_LAST_CW_n."Also, please specify what these registers store.
Quoted 7 lines
Quoted 4 lines
The location register is mainly use for reading controller buffer via BAM mode. The bits of the register
"NAND_READ_LOCATION_LAST_CW_n, n=0..4"
as follow:Perhaps what I do not understand is: when is this "
last_cw" register more useful than the previous set?
From QPIC Version 2.0 onwards it is mandatory to use
"NAND_READ_LOCATION_LAST_CW_n, n=0..4"
register to extract last code word data from controller buffer. Using
register "NAND_READ_LOCATION_n, n=0..4"
we can extract all code words except last code word.
Quoted 14 lines
Quoted 11 lines
[9:0]-bits : (OFFSET) This bit defines the offset from the buffer
base address to be picked up for DMA.
[25:16]-bits: (SIZE) This bit of every register will define the
size of the chunk for DMA.
31-bit : (LAST) If this bit is set, the controller takes the
particular register to specify the last chunk
of data made available for DMA. This chunk is
part of the internal buffer of the controller.Quoted 1 line
Thanks,
Miquèl
Quoted 8 lines · Md Sadre Alam
From QPIC version 2.0 onwards new register got added to read last codeword. This change will update the same.
For first three code word
READ_LOCATION_nregister will be use.For last code wordREAD_LOCATION_LAST_CW_nregister will be use.Signed-off-by Md Sadre Alam <[email protected]>
I gave this patch a try on SDX55 board but not able to resolve an issue and I think it is related to reading the last code word which this patch is trying to address. For my patch on supporting QPIC v2 IP, I tested with SDX55-MTP board and I never hit any issue. But on my new dev board (Telit FN980), there seems to be an issue while populating the partitions and tracing down that bug lands me in copy_last_cw() function.
The issue only happens while creating the 3rd partition on Telit board whose size differs when compared with MTP. The board just reboots into QDL mode whenever it tries to read the last code word.
Below is the snippet of partition layout:
Telit partitions:
[ 1.082015] 0: sbl offs=0x00000000 size=0x0000000a attr:0x000000ff [ 1.082702] 1: mibib offs=0x0000000a size=0x0000000a attr:0x000000ff [ 1.083488] 2: ico offs=0x00000014 size=0x00000014 attr:0x000000ff [ 1.084572] 3: efs2 offs=0x00000028 size=0x0000002c attr:0x000000ff [ 1.085316] 4: tz offs=0x00000054 size=0x00000007 attr:0x000000ff [ 1.086089] 5: tz_devcfg offs=0x0000005b size=0x00000004 attr:0x000000ff
....
MTP partitions:
[ 1.573871] 0: sbl offs=0x00000000 size=0x0000000a attr:0x000000ff [ 1.581139] 1: mibib offs=0x0000000a size=0x0000000a attr:0x000000ff [ 1.587362] 2: efs2 offs=0x00000014 size=0x0000002c attr:0x000000ff [ 1.593853] 3: tz offs=0x00000040 size=0x00000007 attr:0x000000ff [ 1.599860] 4: tz_devcfg offs=0x00000047 size=0x00000004 attr:0x000000ff
...
So until I figure this out, please keep this patch on hold!
Thanks,
Mani
Quoted 163 lines
---
[V3]
* Added else condition for last code word inupdate_rw_regs().drivers/mtd/nand/raw/qcom_nandc.c | 84 ++++++++++++++++++++++++++++++++------- 1 file changed, 70 insertions(+), 14 deletions(-)drivers/mtd/nand/raw/qcom_nandc.c +70
-14@@ -48,6 +48,10 @@#define NAND_READ_LOCATION_1 0xf24#define NAND_READ_LOCATION_2 0xf28#define NAND_READ_LOCATION_3 0xf2c +#define NAND_READ_LOCATION_LAST_CW_0 0xf40 +#define NAND_READ_LOCATION_LAST_CW_1 0xf44 +#define NAND_READ_LOCATION_LAST_CW_2 0xf48 +#define NAND_READ_LOCATION_LAST_CW_3 0xf4c/* dummy register offsets, used by write_reg_dma */ #define NAND_DEV_CMD1_RESTORE 0xdead@@ -187,6 +191,12 @@ nandc_set_reg(nandc, NAND_READ_LOCATION_##reg, \ ((size) << READ_LOCATION_SIZE) | \ ((is_last) << READ_LOCATION_LAST)) +#define nandc_set_read_loc_last (nandc, reg, offset, size, is_last) \ +nandc_set_reg(nandc, NAND_READ_LOCATION_LAST_CW_##reg, \ + ((offset) << READ_LOCATION_OFFSET) | \ + ((size) << READ_LOCATION_SIZE) | \ + ((is_last) << READ_LOCATION_LAST)) +/* * Returns the actual register address for all NAND_DEV_ registers * (i.e. NAND_DEV_CMD0, NAND_DEV_CMD1, NAND_DEV_CMD2 and NAND_DEV_CMD_VLD) @@ -316,6 +326,10 @@ struct nandc_regs {__le32 read_location1;__le32 read_location2;__le32 read_location3; +__le32 read_location_last0; +__le32 read_location_last1; +__le32 read_location_last2; +__le32 read_location_last3;__le32 erased_cw_detect_cfg_clr;__le32 erased_cw_detect_cfg_set;@@ -644,6 +658,14 @@ static __le32 *offset_to_nandc_reg(struct nandc_regs *regs, int offset)return ®s->read_location2;case NAND_READ_LOCATION_3 :return ®s->read_location3; +case NAND_READ_LOCATION_LAST_CW_0 : +return ®s->read_location_last0; +case NAND_READ_LOCATION_LAST_CW_1 : +return ®s->read_location_last1; +case NAND_READ_LOCATION_LAST_CW_2 : +return ®s->read_location_last2; +case NAND_READ_LOCATION_LAST_CW_3 : +return ®s->read_location_last3;default :return NULL ; }@@ -719,9 +741,14 @@ static void update_rw_regs(struct qcom_nand_host *host, int num_cw, bool read)nandc_set_reg (nandc,NAND_READ_STATUS , host->clrreadstatus);nandc_set_reg (nandc,NAND_EXEC_CMD ,1 ); -if (read) -nandc_set_read_loc (nandc,0 ,0 , host->use_ecc ? - host->cw_data : host->cw_size,1 ); +if (read) { +if (nandc->props->qpic_v2) +nandc_set_read_loc_last (nandc,0 ,0 , host->use_ecc ? + host->cw_data : host->cw_size,1 ); +else +nandc_set_read_loc (nandc,0 ,0 , host->use_ecc ? + host->cw_data : host->cw_size,1 ); + } }/* @@ -1096,9 +1123,13 @@ static void config_nand_page_read(struct qcom_nand_controller *nandc)static void config_nand_cw_read (struct qcom_nand_controller *nandc,bool use_ecc) { -if (nandc->props->is_bam) +if (nandc->props->is_bam) { +if (nandc->props->qpic_v2) +write_reg_dma (nandc,NAND_READ_LOCATION_LAST_CW_0 , +1 ,NAND_BAM_NEXT_SGL );write_reg_dma (nandc,NAND_READ_LOCATION_0 ,4 ,NAND_BAM_NEXT_SGL ); + }write_reg_dma (nandc,NAND_FLASH_CMD ,1 ,NAND_BAM_NEXT_SGL );write_reg_dma (nandc,NAND_EXEC_CMD ,1 ,NAND_BAM_NEXT_SGL );@@ -1633,16 +1664,28 @@ qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip, }if (nandc->props->is_bam) { -nandc_set_read_loc (nandc,0 , read_loc, data_size1,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,0 , read_loc, data_size1,0 ); +else +nandc_set_read_loc (nandc,0 , read_loc, data_size1,0 ); read_loc += data_size1; -nandc_set_read_loc (nandc,1 , read_loc, oob_size1,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,1 , read_loc, oob_size1,0 ); +else +nandc_set_read_loc (nandc,1 , read_loc, oob_size1,0 ); read_loc += oob_size1; -nandc_set_read_loc (nandc,2 , read_loc, data_size2,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,2 , read_loc, data_size2,0 ); +else +nandc_set_read_loc (nandc,2 , read_loc, data_size2,0 ); read_loc += data_size2; -nandc_set_read_loc (nandc,3 , read_loc, oob_size2,1 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,3 , read_loc, oob_size2,0 ); +else +nandc_set_read_loc (nandc,3 , read_loc, oob_size2,1 ); }config_nand_cw_read (nandc, false);@@ -1873,14 +1916,27 @@ static int read_page_ecc(struct qcom_nand_host *host, u8 *data_buf,if (nandc->props->is_bam) {if (data_buf && oob_buf) { -nandc_set_read_loc (nandc,0 ,0 , data_size,0 ); -nandc_set_read_loc (nandc,1 , data_size, - oob_size,1 ); +if (nandc->props->qpic_v2 && i == (ecc->steps -1 )) { +nandc_set_read_loc_last (nandc,0 ,0 , data_size,0 ); +nandc_set_read_loc_last (nandc,1 , data_size, + oob_size,1 ); + }else { +nandc_set_read_loc (nandc,0 ,0 , data_size,0 ); +nandc_set_read_loc (nandc,1 , data_size, + oob_size,1 ); + } }else if (data_buf) { -nandc_set_read_loc (nandc,0 ,0 , data_size,1 ); +if (nandc->props->qpic_v2 && i == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,0 ,0 , data_size,1 ); +else +nandc_set_read_loc (nandc,0 ,0 , data_size,1 ); }else { -nandc_set_read_loc (nandc,0 , data_size, - oob_size,1 ); +if (nandc->props->qpic_v2 && i == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,0 , data_size, + oob_size,1 ); +else +nandc_set_read_loc (nandc,0 , data_size, + oob_size,1 ); } }Signature · 1 line
2.7.4
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Quoted 35 lines · Manivannan Sadhasivam
Quoted 8 lines · Md Sadre Alam
From QPIC version 2.0 onwards new register got added to read last codeword. This change will update the same.
For first three code word
READ_LOCATION_nregister will be use.For last code wordREAD_LOCATION_LAST_CW_nregister will be use.Signed-off-by Md Sadre Alam <[email protected]>I gave this patch a try on SDX55 board but not able to resolve an issue and I think it is related to reading the last code word which this patch is trying to address. For my patch on supporting QPIC v2 IP, I tested with SDX55-MTP board and I never hit any issue. But on my new dev board (Telit FN980), there seems to be an issue while populating the partitions and tracing down that bug lands me in
copy_last_cw()function.The issue only happens while creating the 3rd partition on Telit board whose size differs when compared with MTP. The board just reboots into QDL mode whenever it tries to read the last code word.
Below is the snippet of partition layout:
Telit partitions:
[ 1.082015] 0: sbl offs=0x00000000 size=0x0000000a attr:0x000000ff [ 1.082702] 1: mibib offs=0x0000000a size=0x0000000a attr:0x000000ff [ 1.083488] 2: ico offs=0x00000014 size=0x00000014 attr:0x000000ff [ 1.084572] 3: efs2 offs=0x00000028 size=0x0000002c attr:0x000000ff [ 1.085316] 4: tz offs=0x00000054 size=0x00000007 attr:0x000000ff [ 1.086089] 5: tz_devcfg offs=0x0000005b size=0x00000004 attr:0x000000ff....
MTP partitions:
Quoted 8 lines
[ 1.573871] 0: sbl offs=0x00000000 size=0x0000000a attr:0x000000ff [ 1.581139] 1: mibib offs=0x0000000a size=0x0000000a attr:0x000000ff [ 1.587362] 2: efs2 offs=0x00000014 size=0x0000002c attr:0x000000ff [ 1.593853] 3: tz offs=0x00000040 size=0x00000007 attr:0x000000ff [ 1.599860] 4: tz_devcfg offs=0x00000047 size=0x00000004 attr:0x000000ff...
So until I figure this out, please keep this patch on hold!
There was some corner case I missed in V3 patch. I have fixed this in
V4 patch.
I have done some tress testing as well with V4 patch on IPQ5018
platform using "nand-utils"
and "mtd_test.ko" , Now its working fine. Can you test with V4 patch
once.
Quoted 172 lines
Thanks,
ManiQuoted 168 lines
---
[V3]
* Added else condition for last code word inupdate_rw_regs().drivers/mtd/nand/raw/qcom_nandc.c | 84 ++++++++++++++++++++++++++++++++------- 1 file changed, 70 insertions(+), 14 deletions(-)drivers/mtd/nand/raw/qcom_nandc.c +10
-0@@ -48,6 +48,10 @@#define NAND_READ_LOCATION_1 0xf24#define NAND_READ_LOCATION_2 0xf28#define NAND_READ_LOCATION_3 0xf2c +#define NAND_READ_LOCATION_LAST_CW_0 0xf40 +#define NAND_READ_LOCATION_LAST_CW_1 0xf44 +#define NAND_READ_LOCATION_LAST_CW_2 0xf48 +#define NAND_READ_LOCATION_LAST_CW_3 0xf4c/* dummy register offsets, used by write_reg_dma */ #define NAND_DEV_CMD1_RESTORE 0xdead@@ -187,6 +191,12 @@ nandc_set_reg(nandc, NAND_READ_LOCATION_##reg, \ ((size) << READ_LOCATION_SIZE) | \ ((is_last) << READ_LOCATION_LAST)) +#define nandc_set_read_loc_last (nandc, reg, offset, size, is_last) \ +nandc_set_reg(nandc, NAND_READ_LOCATION_LAST_CW_##reg, \ + ((offset) << READ_LOCATION_OFFSET) | \ + ((size) << READ_LOCATION_SIZE) | \ + ((is_last) << READ_LOCATION_LAST)) +/* * Returns the actual register address for all NAND_DEV_ registers * (i.e.
NAND_DEV_CMD0,NAND_DEV_CMD1,NAND_DEV_CMD2andNAND_DEV_CMD_VLD)drivers/mtd/nand/raw/qcom_nandc.c +12
-0@@ -316,6 +326,10 @@ struct nandc_regs {__le32 read_location1;__le32 read_location2;__le32 read_location3; +__le32 read_location_last0; +__le32 read_location_last1; +__le32 read_location_last2; +__le32 read_location_last3;__le32 erased_cw_detect_cfg_clr;__le32 erased_cw_detect_cfg_set;@@ -644,6 +658,14 @@ static __le32 *offset_to_nandc_reg(struct nandc_regs *regs, int offset)return ®s->read_location2;case NAND_READ_LOCATION_3 :return ®s->read_location3; +case NAND_READ_LOCATION_LAST_CW_0 : +return ®s->read_location_last0; +case NAND_READ_LOCATION_LAST_CW_1 : +return ®s->read_location_last1; +case NAND_READ_LOCATION_LAST_CW_2 : +return ®s->read_location_last2; +case NAND_READ_LOCATION_LAST_CW_3 : +return ®s->read_location_last3;default :return NULL ;drivers/mtd/nand/raw/qcom_nandc.c +8
-3}@@ -719,9 +741,14 @@ static void update_rw_regs(struct qcom_nand_host *host, int num_cw, bool read)nandc_set_reg (nandc,NAND_READ_STATUS , host->clrreadstatus);nandc_set_reg (nandc,NAND_EXEC_CMD ,1 ); -if (read) -nandc_set_read_loc (nandc,0 ,0 , host->use_ecc ? - host->cw_data : host->cw_size,1 ); +if (read) { +if (nandc->props->qpic_v2) +nandc_set_read_loc_last (nandc,0 ,0 , host->use_ecc ? + host->cw_data : host->cw_size,1 ); +else +nandc_set_read_loc (nandc,0 ,0 , host->use_ecc ? + host->cw_data : host->cw_size,1 ); + } }/*
drivers/mtd/nand/raw/qcom_nandc.c +5
-1@@ -1096,9 +1123,13 @@ static void config_nand_page_read(struct qcom_nand_controller *nandc)static void config_nand_cw_read (struct qcom_nand_controller *nandc,bool use_ecc) { -if (nandc->props->is_bam) +if (nandc->props->is_bam) { +if (nandc->props->qpic_v2) +write_reg_dma (nandc,NAND_READ_LOCATION_LAST_CW_0 , +1 ,NAND_BAM_NEXT_SGL );write_reg_dma (nandc,NAND_READ_LOCATION_0 ,4 ,NAND_BAM_NEXT_SGL ); + }write_reg_dma (nandc,NAND_FLASH_CMD ,1 ,NAND_BAM_NEXT_SGL );drivers/mtd/nand/raw/qcom_nandc.c +16
-4write_reg_dma (nandc,NAND_EXEC_CMD ,1 ,NAND_BAM_NEXT_SGL );@@ -1633,16 +1664,28 @@ qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip, }if (nandc->props->is_bam) { -nandc_set_read_loc (nandc,0 , read_loc, data_size1,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,0 , read_loc, data_size1,0 ); +else +nandc_set_read_loc (nandc,0 , read_loc, data_size1,0 ); read_loc += data_size1; -nandc_set_read_loc (nandc,1 , read_loc, oob_size1,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,1 , read_loc, oob_size1,0 ); +else +nandc_set_read_loc (nandc,1 , read_loc, oob_size1,0 ); read_loc += oob_size1; -nandc_set_read_loc (nandc,2 , read_loc, data_size2,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,2 , read_loc, data_size2,0 ); +else +nandc_set_read_loc (nandc,2 , read_loc, data_size2,0 ); read_loc += data_size2; -nandc_set_read_loc (nandc,3 , read_loc, oob_size2,1 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,3 , read_loc, oob_size2,0 ); +else +nandc_set_read_loc (nandc,3 , read_loc, oob_size2,1 ); }drivers/mtd/nand/raw/qcom_nandc.c +19
-6config_nand_cw_read (nandc, false);@@ -1873,14 +1916,27 @@ static int read_page_ecc(struct qcom_nand_host *host, u8 *data_buf, if (nandc->props->is_bam) {if (data_buf && oob_buf) { -nandc_set_read_loc (nandc,0 ,0 , data_size,0 ); -nandc_set_read_loc (nandc,1 , data_size, - oob_size,1 ); +if (nandc->props->qpic_v2 && i == (ecc->steps -1 )) { +nandc_set_read_loc_last (nandc,0 ,0 , data_size,0 ); +nandc_set_read_loc_last (nandc,1 , data_size, + oob_size,1 ); + }else { +nandc_set_read_loc (nandc,0 ,0 , data_size,0 ); +nandc_set_read_loc (nandc,1 , data_size, + oob_size,1 ); + } }else if (data_buf) { -nandc_set_read_loc (nandc,0 ,0 , data_size,1 ); +if (nandc->props->qpic_v2 && i == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,0 ,0 , data_size,1 ); +else +nandc_set_read_loc (nandc,0 ,0 , data_size,1 ); }else { -nandc_set_read_loc (nandc,0 , data_size, - oob_size,1 ); +if (nandc->props->qpic_v2 && i == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,0 , data_size, + oob_size,1 ); +else +nandc_set_read_loc (nandc,0 , data_size, + oob_size,1 ); } }
Quoted 3 lines
Quoted 3 lines
--
2.7.4
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Quoted 43 lines · On 2021-01-29 10:41, [email protected] wrote:
Quoted 42 lines · Manivannan Sadhasivam
Quoted 8 lines · Md Sadre Alam
From QPIC version 2.0 onwards new register got added to read last codeword. This change will update the same.
For first three code word
READ_LOCATION_nregister will be use.For last code wordREAD_LOCATION_LAST_CW_nregister will be use.Signed-off-by Md Sadre Alam <[email protected]>I gave this patch a try on SDX55 board but not able to resolve an issue and I think it is related to reading the last code word which this patch is trying to address. For my patch on supporting QPIC v2 IP, I tested with SDX55-MTP board and I never hit any issue. But on my new dev board (Telit FN980), there seems to be an issue while populating the partitions and tracing down that bug lands me in
copy_last_cw()function.The issue only happens while creating the 3rd partition on Telit board whose size differs when compared with MTP. The board just reboots into QDL mode whenever it tries to read the last code word.
Below is the snippet of partition layout:
Telit partitions:
[ 1.082015] 0: sbl offs=0x00000000 size=0x0000000a attr:0x000000ff [ 1.082702] 1: mibib offs=0x0000000a size=0x0000000a attr:0x000000ff [ 1.083488] 2: ico offs=0x00000014 size=0x00000014 attr:0x000000ff [ 1.084572] 3: efs2 offs=0x00000028 size=0x0000002c attr:0x000000ff [ 1.085316] 4: tz offs=0x00000054 size=0x00000007 attr:0x000000ff [ 1.086089] 5: tz_devcfg offs=0x0000005b size=0x00000004 attr:0x000000ff....
MTP partitions:
[ 1.573871] 0: sbl offs=0x00000000 size=0x0000000a attr:0x000000ff [ 1.581139] 1: mibib offs=0x0000000a size=0x0000000a attr:0x000000ff [ 1.587362] 2: efs2 offs=0x00000014 size=0x0000002c attr:0x000000ff [ 1.593853] 3: tz offs=0x00000040 size=0x00000007 attr:0x000000ff [ 1.599860] 4: tz_devcfg offs=0x00000047 size=0x00000004 attr:0x000000ff...
Quoted 8 lines
Quoted 1 line
So until I figure this out, please keep this patch on hold!
There was some corner case I missed in V3 patch. I have fixed this
in V4 patch.
I have done some tress testing as well with V4 patch on IPQ5018
platform using "nand-utils"
and "mtd_test.ko" , Now its working fine. Can you test with V4 patch
once.
ping! Do you need some more info for the V4 patch ?
Quoted 173 lines
Quoted 173 lines
Thanks,
ManiQuoted 169 lines
---
[V3]
* Added else condition for last code word inupdate_rw_regs().drivers/mtd/nand/raw/qcom_nandc.c | 84 ++++++++++++++++++++++++++++++++------- 1 file changed, 70 insertions(+), 14 deletions(-)drivers/mtd/nand/raw/qcom_nandc.c +10
-0@@ -48,6 +48,10 @@#define NAND_READ_LOCATION_1 0xf24#define NAND_READ_LOCATION_2 0xf28#define NAND_READ_LOCATION_3 0xf2c +#define NAND_READ_LOCATION_LAST_CW_0 0xf40 +#define NAND_READ_LOCATION_LAST_CW_1 0xf44 +#define NAND_READ_LOCATION_LAST_CW_2 0xf48 +#define NAND_READ_LOCATION_LAST_CW_3 0xf4c/* dummy register offsets, used by write_reg_dma */ #define NAND_DEV_CMD1_RESTORE 0xdead@@ -187,6 +191,12 @@ nandc_set_reg(nandc, NAND_READ_LOCATION_##reg, \ ((size) << READ_LOCATION_SIZE) | \ ((is_last) << READ_LOCATION_LAST)) +#define nandc_set_read_loc_last (nandc, reg, offset, size, is_last) \ +nandc_set_reg(nandc, NAND_READ_LOCATION_LAST_CW_##reg, \ + ((offset) << READ_LOCATION_OFFSET) | \ + ((size) << READ_LOCATION_SIZE) | \ + ((is_last) << READ_LOCATION_LAST)) +/* * Returns the actual register address for all NAND_DEV_ registers * (i.e.
NAND_DEV_CMD0,NAND_DEV_CMD1,NAND_DEV_CMD2andNAND_DEV_CMD_VLD)drivers/mtd/nand/raw/qcom_nandc.c +12
-0@@ -316,6 +326,10 @@ struct nandc_regs {__le32 read_location1;__le32 read_location2;__le32 read_location3; +__le32 read_location_last0; +__le32 read_location_last1; +__le32 read_location_last2; +__le32 read_location_last3;__le32 erased_cw_detect_cfg_clr;__le32 erased_cw_detect_cfg_set;@@ -644,6 +658,14 @@ static __le32 *offset_to_nandc_reg(struct nandc_regs *regs, int offset)return ®s->read_location2;case NAND_READ_LOCATION_3 :return ®s->read_location3; +case NAND_READ_LOCATION_LAST_CW_0 : +return ®s->read_location_last0; +case NAND_READ_LOCATION_LAST_CW_1 : +return ®s->read_location_last1; +case NAND_READ_LOCATION_LAST_CW_2 : +return ®s->read_location_last2; +case NAND_READ_LOCATION_LAST_CW_3 : +return ®s->read_location_last3;default :return NULL ;drivers/mtd/nand/raw/qcom_nandc.c +8
-3}@@ -719,9 +741,14 @@ static void update_rw_regs(struct qcom_nand_host *host, int num_cw, bool read)nandc_set_reg (nandc,NAND_READ_STATUS , host->clrreadstatus);nandc_set_reg (nandc,NAND_EXEC_CMD ,1 ); -if (read) -nandc_set_read_loc (nandc,0 ,0 , host->use_ecc ? - host->cw_data : host->cw_size,1 ); +if (read) { +if (nandc->props->qpic_v2) +nandc_set_read_loc_last (nandc,0 ,0 , host->use_ecc ? + host->cw_data : host->cw_size,1 ); +else +nandc_set_read_loc (nandc,0 ,0 , host->use_ecc ? + host->cw_data : host->cw_size,1 ); + } }/*
drivers/mtd/nand/raw/qcom_nandc.c +5
-1@@ -1096,9 +1123,13 @@ static void config_nand_page_read(struct qcom_nand_controller *nandc)static void config_nand_cw_read (struct qcom_nand_controller *nandc,bool use_ecc) { -if (nandc->props->is_bam) +if (nandc->props->is_bam) { +if (nandc->props->qpic_v2) +write_reg_dma (nandc,NAND_READ_LOCATION_LAST_CW_0 , +1 ,NAND_BAM_NEXT_SGL );write_reg_dma (nandc,NAND_READ_LOCATION_0 ,4 ,NAND_BAM_NEXT_SGL ); + }drivers/mtd/nand/raw/qcom_nandc.c +16
-4write_reg_dma (nandc,NAND_FLASH_CMD ,1 ,NAND_BAM_NEXT_SGL );write_reg_dma (nandc,NAND_EXEC_CMD ,1 ,NAND_BAM_NEXT_SGL );@@ -1633,16 +1664,28 @@ qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip, }if (nandc->props->is_bam) { -nandc_set_read_loc (nandc,0 , read_loc, data_size1,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,0 , read_loc, data_size1,0 ); +else +nandc_set_read_loc (nandc,0 , read_loc, data_size1,0 ); read_loc += data_size1; -nandc_set_read_loc (nandc,1 , read_loc, oob_size1,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,1 , read_loc, oob_size1,0 ); +else +nandc_set_read_loc (nandc,1 , read_loc, oob_size1,0 ); read_loc += oob_size1; -nandc_set_read_loc (nandc,2 , read_loc, data_size2,0 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,2 , read_loc, data_size2,0 ); +else +nandc_set_read_loc (nandc,2 , read_loc, data_size2,0 ); read_loc += data_size2; -nandc_set_read_loc (nandc,3 , read_loc, oob_size2,1 ); +if (nandc->props->qpic_v2 && cw == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,3 , read_loc, oob_size2,0 ); +else +nandc_set_read_loc (nandc,3 , read_loc, oob_size2,1 ); }drivers/mtd/nand/raw/qcom_nandc.c +19
-6config_nand_cw_read (nandc, false);@@ -1873,14 +1916,27 @@ static int read_page_ecc(struct qcom_nand_host *host, u8 *data_buf, if (nandc->props->is_bam) {if (data_buf && oob_buf) { -nandc_set_read_loc (nandc,0 ,0 , data_size,0 ); -nandc_set_read_loc (nandc,1 , data_size, - oob_size,1 ); +if (nandc->props->qpic_v2 && i == (ecc->steps -1 )) { +nandc_set_read_loc_last (nandc,0 ,0 , data_size,0 ); +nandc_set_read_loc_last (nandc,1 , data_size, + oob_size,1 ); + }else { +nandc_set_read_loc (nandc,0 ,0 , data_size,0 ); +nandc_set_read_loc (nandc,1 , data_size, + oob_size,1 ); + } }else if (data_buf) { -nandc_set_read_loc (nandc,0 ,0 , data_size,1 ); +if (nandc->props->qpic_v2 && i == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,0 ,0 , data_size,1 ); +else +nandc_set_read_loc (nandc,0 ,0 , data_size,1 ); }else { -nandc_set_read_loc (nandc,0 , data_size, - oob_size,1 ); +if (nandc->props->qpic_v2 && i == (ecc->steps -1 )) +nandc_set_read_loc_last (nandc,0 , data_size, + oob_size,1 ); +else +nandc_set_read_loc (nandc,0 , data_size, + oob_size,1 ); } }
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
--
2.7.4
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/