FAILED: patch "[PATCH] usb: dwc3: ulpi: Replace CPU-based busyloop with" failed to apply to 4.19-stable tree

The patch below does not apply to the 4.19-stable tree.
If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <[email protected]>.

thanks,

greg k-h

------------------ original commit in Linus's tree ------------------

From fca3f138105727c3a22edda32d02f91ce1bf11c9 Mon Sep 17 00:00:00 2001
From: Serge Semin <[email protected]>
Date: Thu, 10 Dec 2020 11:50:07 +0300
Subject: [PATCH] usb: dwc3: ulpi: Replace CPU-based busyloop with
Protocol-based one

Originally the procedure of the ULPI transaction finish detection has been developed as a simple busy-loop with just decrementing counter and no delays. It's wrong since on different systems the loop will take a different time to complete. So if the system bus and CPU are fast enough to overtake the ULPI bus and the companion PHY reaction, then we'll get to take a false timeout error. Fix this by converting the busy-loop procedure to take the standard bus speed, address value and the registers access mode into account for the busy-loop delay calculation.

Here is the way the fix works. It's known that the ULPI bus is clocked with 60MHz signal. In accordance with [1] the ULPI bus protocol is created so to spend 5 and 6 clock periods for immediate register write and read operations respectively, and 6 and 7 clock periods - for the extended register writes and reads. Based on that we can easily pre-calculate the time which will be needed for the controller to perform a requested IO operation. Note we'll still preserve the attempts counter in case if the DWC USB3 controller has got some internals delays.

[1] UTMI+ Low Pin Interface (ULPI) Specification, Revision 1.1,

    October 20, 2004, pp. 30 - 36.

index 3cc4f4970c05..54c877f7b51d 100644
@@ -7,6 +7,8 @@
  * Author: Heikki Krogerus <[email protected]>
  */
 
+#include <linux/delay.h>
+#include <linux/time64.h>
 #include <linux/ulpi/regs.h>
 
 #include "core.h"

@@ -17,12 +19,22 @@
 		DWC3_GUSB2PHYACC_ADDR(ULPI_ACCESS_EXTENDED) | \
 		DWC3_GUSB2PHYACC_EXTEND_ADDR(a) : DWC3_GUSB2PHYACC_ADDR(a))
 
-static int dwc3_ulpi_busyloop(struct dwc3 *dwc)
+#define DWC3_ULPI_BASE_DELAY	DIV_ROUND_UP(NSEC_PER_SEC, 60000000L)
+
+static int dwc3_ulpi_busyloop(struct dwc3 *dwc, u8 addr, bool read)
 {
+	unsigned long ns = 5L * DWC3_ULPI_BASE_DELAY;
 	unsigned int count = 1000;
 	u32 reg;
 
+	if (addr >= ULPI_EXT_VENDOR_SPECIFIC)
+		ns += DWC3_ULPI_BASE_DELAY;
+
+	if (read)
+		ns += DWC3_ULPI_BASE_DELAY;
+
 	while (count--) {
+		ndelay(ns);
 		reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYACC(0));
 		if (reg & DWC3_GUSB2PHYACC_DONE)
 			return 0;

@@ -47,7 +59,7 @@ static int dwc3_ulpi_read(struct device *dev, u8 addr)
 	reg = DWC3_GUSB2PHYACC_NEWREGREQ | DWC3_ULPI_ADDR(addr);
 	dwc3_writel(dwc->regs, DWC3_GUSB2PHYACC(0), reg);
 
-	ret = dwc3_ulpi_busyloop(dwc);
+	ret = dwc3_ulpi_busyloop(dwc, addr, true);
 	if (ret)
 		return ret;
 

@@ -71,7 +83,7 @@ static int dwc3_ulpi_write(struct device *dev, u8 addr, u8 val)
 	reg |= DWC3_GUSB2PHYACC_WRITE | val;
 	dwc3_writel(dwc->regs, DWC3_GUSB2PHYACC(0), reg);
 
-	return dwc3_ulpi_busyloop(dwc);
+	return dwc3_ulpi_busyloop(dwc, addr, false);
 }
 
 static const struct ulpi_ops dwc3_ulpi_ops = {