board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support
Subsystems (3)
PATCH v3 1/1 board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support
Add initial support PHYTEC phyCORE-i.MX8MP SOM.
Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog
---
Changes in v3:
- switched to accepted upstream kernel device tree
(http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/629277.html)
- added Reviewed-by
Changes in v2:
- remove not needed spl board init
- remove ifdef from board_fit_config_name_match
- disabled not needed i2c busses from defconfig
- not use size macro for PHYS_SDRAM
- remove makros from phycore_imx8mp.h that are defined elsewhere
arch/arm/dts/Makefile | 1 + .../arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi | 114 ++ arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts | 161 ++ arch/arm/dts/imx8mp-phycore-som.dtsi | 293 ++++ arch/arm/mach-imx/imx8m/Kconfig | 7 + board/phytec/phycore_imx8mp/Kconfig | 12 + board/phytec/phycore_imx8mp/MAINTAINERS | 9 + board/phytec/phycore_imx8mp/Makefile | 11 + board/phytec/phycore_imx8mp/lpddr4_timing.c | 1849 ++++++++++++++++++++ board/phytec/phycore_imx8mp/phycore-imx8mp.c | 39 + board/phytec/phycore_imx8mp/spl.c | 129 ++ configs/phycore-imx8mp_defconfig | 95 + include/configs/phycore_imx8mp.h | 107 ++ 13 files changed, 2827 insertions(+) create mode 100644 arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi create mode 100644 arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts create mode 100644 arch/arm/dts/imx8mp-phycore-som.dtsi create mode 100644 board/phytec/phycore_imx8mp/Kconfig create mode 100644 board/phytec/phycore_imx8mp/MAINTAINERS create mode 100644 board/phytec/phycore_imx8mp/Makefile create mode 100644 board/phytec/phycore_imx8mp/lpddr4_timing.c create mode 100644 board/phytec/phycore_imx8mp/phycore-imx8mp.c create mode 100644 board/phytec/phycore_imx8mp/spl.c create mode 100644 configs/phycore-imx8mp_defconfig create mode 100644 include/configs/phycore_imx8mp.h
arch/arm/dts/Makefile +1 -0
@@ -780,6 +780,7 @@ dtb-$(CONFIG_ARCH_IMX8M) += \ imx8mm-beacon-kit.dtb \ imx8mq-phanbell.dtb \ imx8mp-evk.dtb \ + imx8mp-phyboard-pollux-rdk.dtb \ imx8mq-pico-pi.dtb dtb-$(CONFIG_ARCH_IMXRT) += imxrt1050-evk.dtb \
arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi new file +114 -0
114 lines not on this page · raw message
arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts new file +161 -0
161 lines not on this page · raw message
arch/arm/dts/imx8mp-phycore-som.dtsi new file +293 -0
293 lines not on this page · raw message
arch/arm/mach-imx/imx8m/Kconfig +7 -0
@@ -77,6 +77,12 @@ config TARGET_PHYCORE_IMX8MM select IMX8MM select SUPPORT_SPL select IMX8M_LPDDR4 + +config TARGET_PHYCORE_IMX8MP + bool "PHYTEC PHYCORE i.MX8MP" + select IMX8MP + select SUPPORT_SPL + select IMX8M_LPDDR4 endchoice source "board/freescale/imx8mq_evk/Kconfig"
@@ -88,5 +94,6 @@ source "board/technexion/pico-imx8mq/Kconfig" source "board/toradex/verdin-imx8mm/Kconfig" source "board/beacon/imx8mm/Kconfig" source "board/phytec/phycore_imx8mm/Kconfig" +source "board/phytec/phycore_imx8mp/Kconfig" endif
board/phytec/phycore_imx8mp/Kconfig new file +12 -0
@@ -0,0 +1,12 @@ +if TARGET_PHYCORE_IMX8MP + +config SYS_BOARD + default "phycore_imx8mp" + +config SYS_VENDOR + default "phytec" + +config SYS_CONFIG_NAME + default "phycore_imx8mp" + +endif
board/phytec/phycore_imx8mp/MAINTAINERS new file +9 -0
@@ -0,0 +1,9 @@ +phyCORE-i.MX8M Plus +M: Teresa Remmet <[email protected]> +W: https://www.phytec.eu/product-eu/system-on-modules/phycore-imx-8m-plus/ +S: Maintained +F: arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts +F: arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi +F: board/phytec/phycore_imx8mp/ +F: configs/phycore-imx8mp_defconfig +F: include/configs/phycore_imx8mp.h
board/phytec/phycore_imx8mp/Makefile new file +11 -0
@@ -0,0 +1,11 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# +# Copyright (C) 2020 PHYTEC Messtechnik GmbH +# Author: Teresa Remmet <[email protected]> + +obj-y += phycore-imx8mp.o + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +obj-$(CONFIG_IMX8M_LPDDR4) += lpddr4_timing.o +endif
board/phytec/phycore_imx8mp/lpddr4_timing.c new file +1849 -0
1,849 lines not on this page · raw message
board/phytec/phycore_imx8mp/phycore-imx8mp.c new file +39 -0
@@ -0,0 +1,39 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* +* Copyright (C) 2020 PHYTEC Messtechnik GmbH +* Author: Teresa Remmet <[email protected]> +*/ + +#include <common.h> +#include <asm/arch/sys_proto.h> +#include <asm/io.h> +#include <asm/mach-imx/boot_mode.h> +#include <env.h> + +DECLARE_GLOBAL_DATA_PTR ; + +int board_init (void ) +{ +return 0 ; +} + +int board_mmc_get_env_dev (int devno) +{ +return devno; +} + +int board_late_init (void ) +{ +switch (get_boot_device ()) { +case SD2_BOOT : +env_set_ulong ("mmcdev" ,1 ); +break ; +case MMC3_BOOT : +env_set_ulong ("mmcdev" ,2 ); +break ; +default : +break ; + } + +return 0 ; +}
board/phytec/phycore_imx8mp/spl.c new file +129 -0
129 lines not on this page · raw message
configs/phycore-imx8mp_defconfig new file +95 -0
95 lines not on this page · raw message
include/configs/phycore_imx8mp.h new file +107 -0
107 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v3 1/1 board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support
Quoted 9 lines
Add initial support PHYTEC phyCORE-i.MX8MP SOM.
Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdogSigned-off-by Teresa Remmet <[email protected]>Reviewed-by Heiko Schocher <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================