Skip to contentSkip to conversation

regulator: pf8x00: Add suspend support

PATCH In review Christoph Fritz 3 participants 7 messages Jan 17, 2021 – Jan 26, 2021

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 regulator: pf8x00: Add suspend support

This patch adds suspend/resume support so that it is possible to configure the LDOs and BUCKs as on or off during suspend phase as well as to configure suspend specific voltages.

---
 drivers/regulator/pf8x00-regulator.c | 75 ++++++++++++++++++++++++++--
 1 file changed, 70 insertions(+), 5 deletions(-)
drivers/regulator/pf8x00-regulator.c +70 -5
index 1e5582d73405..02892e04acce 100644
@@ -125,8 +125,12 @@ enum pf8x00_devid {
 #define PF8X00_DEVICE_FAM_MASK		GENMASK(7, 4)
 #define PF8X00_DEVICE_ID_MASK		GENMASK(3, 0)
 
-struct pf8x00_regulator {
+struct pf8x00_regulator_data {
 	struct regulator_desc desc;
+	unsigned int suspend_enable_reg;
+	unsigned int suspend_enable_mask;
+	unsigned int suspend_voltage_reg;
+	unsigned int suspend_voltage_cache;
 };
 
 struct pf8x00_chip {
@@ -276,6 +280,53 @@ static int pf8x00_of_parse_cb(struct device_node *np,
 	return 0;
 }
 
+static int pf8x00_suspend_enable(struct regulator_dev *rdev)
+{
+	struct pf8x00_regulator_data *regl = rdev_get_drvdata(rdev);
+	struct regmap *rmap = rdev_get_regmap(rdev);
+
+	return regmap_update_bits(rmap, regl->suspend_enable_reg,
+				  regl->suspend_enable_mask,
+				  regl->suspend_enable_mask);
+}
+
+static int pf8x00_suspend_disable(struct regulator_dev *rdev)
+{
+	struct pf8x00_regulator_data *regl = rdev_get_drvdata(rdev);
+	struct regmap *rmap = rdev_get_regmap(rdev);
+
+	return regmap_update_bits(rmap, regl->suspend_enable_reg,
+				  regl->suspend_enable_mask, 0);
+}
+
+static int pf8x00_set_suspend_voltage(struct regulator_dev *rdev, int uV)
+{
+	struct pf8x00_regulator_data *regl = rdev_get_drvdata(rdev);
+	int ret;
+
+	if (regl->suspend_voltage_cache == uV)
+		return 0;
+
+	ret = regulator_map_voltage_iterate(rdev, uV, uV);
+	if (ret < 0) {
+		dev_err(rdev_get_dev(rdev), "failed to map %i uV\n", uV);
+		return ret;
+	}
+
+	dev_dbg(rdev_get_dev(rdev), "uV: %i, reg: 0x%x, msk: 0x%x, val: 0x%x\n",
+		uV, regl->suspend_voltage_reg, regl->desc.vsel_mask, ret);
+	ret = regmap_update_bits(rdev->regmap, regl->suspend_voltage_reg,
+				 regl->desc.vsel_mask, ret);
+	if (ret < 0) {
+		dev_err(rdev_get_dev(rdev), "failed to set %i uV\n", uV);
+		return ret;
+	}
+
+	regl->suspend_voltage_cache = uV;
+
+	return 0;
+}
+
 static const struct regulator_ops pf8x00_ldo_ops = {
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
@@ -283,6 +334,9 @@ static const struct regulator_ops pf8x00_ldo_ops = {
 	.list_voltage = regulator_list_voltage_table,
 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_suspend_enable = pf8x00_suspend_enable,
+	.set_suspend_disable = pf8x00_suspend_disable,
+	.set_suspend_voltage = pf8x00_set_suspend_voltage,
 };
 
 
@@ -295,6 +349,9 @@ static const struct regulator_ops pf8x00_buck1_6_ops = {
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 	.get_current_limit = regulator_get_current_limit_regmap,
 	.set_current_limit = regulator_set_current_limit_regmap,
+	.set_suspend_enable = pf8x00_suspend_enable,
+	.set_suspend_disable = pf8x00_suspend_disable,
+	.set_suspend_voltage = pf8x00_set_suspend_voltage,
 };
 
 static const struct regulator_ops pf8x00_buck7_ops = {
@@ -306,6 +363,8 @@ static const struct regulator_ops pf8x00_buck7_ops = {
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 	.get_current_limit = regulator_get_current_limit_regmap,
 	.set_current_limit = regulator_set_current_limit_regmap,
+	.set_suspend_enable = pf8x00_suspend_enable,
+	.set_suspend_disable = pf8x00_suspend_disable,
 };
 
 static const struct regulator_ops pf8x00_vsnvs_ops = {
@@ -337,6 +396,9 @@ static const struct regulator_ops pf8x00_vsnvs_ops = {
 			.disable_val = 0x0,			\
 			.enable_mask = 2,			\
 		},						\
+		.suspend_enable_reg = (base) + LDO_CONFIG2,	\
+		.suspend_enable_mask = 1,			\
+		.suspend_voltage_reg = (base) + LDO_STBY_VOLT,	\
 	}
 
 #define PF8X00BUCK(_id, _name, base, voltages)			\
@@ -367,6 +429,9 @@ static const struct regulator_ops pf8x00_vsnvs_ops = {
 			.enable_mask = 0x3,			\
 			.enable_time = 500,			\
 		},						\
+		.suspend_enable_reg = (base) + SW_MODE1,	\
+		.suspend_enable_mask = 0xc,			\
+		.suspend_voltage_reg = (base) + SW_STBY_VOLT,	\
 	}
 
 #define PF8X00BUCK7(_name, base, voltages)			\
@@ -415,7 +480,7 @@ static const struct regulator_ops pf8x00_vsnvs_ops = {
 		},						\
 	}
 
-static struct pf8x00_regulator pf8x00_regulators_data[PF8X00_MAX_REGULATORS] = {
+static struct pf8x00_regulator_data pf8x00_regs_data[PF8X00_MAX_REGULATORS] = {
 	PF8X00LDO(1, "ldo1", PF8X00_LDO_BASE(PF8X00_LDO1), pf8x00_ldo_voltages),
 	PF8X00LDO(2, "ldo2", PF8X00_LDO_BASE(PF8X00_LDO2), pf8x00_ldo_voltages),
 	PF8X00LDO(3, "ldo3", PF8X00_LDO_BASE(PF8X00_LDO3), pf8x00_ldo_voltages),
@@ -500,12 +565,12 @@ static int pf8x00_i2c_probe(struct i2c_client *client)
 	if (ret)
 		return ret;
 
-	for (id = 0; id < ARRAY_SIZE(pf8x00_regulators_data); id++) {
-		struct pf8x00_regulator *data = &pf8x00_regulators_data[id];
+	for (id = 0; id < ARRAY_SIZE(pf8x00_regs_data); id++) {
+		struct pf8x00_regulator_data *data = &pf8x00_regs_data[id];
 		struct regulator_dev *rdev;
 
 		config.dev = chip->dev;
-		config.driver_data = chip;
+		config.driver_data = data;
 		config.regmap = chip->regmap;
 
 		rdev = devm_regulator_register(&client->dev, &data->desc, &config);
Signature · 1 line
2.29.2
#1 lore raw

Hello Jagan,

as your new role as Maintainer of this driver, is there a chance to get
your Feedback/Ack/Review/Signed anytime soon?

Thanks
-- Christoph

Quoted 155 lines · Christoph Fritz

This patch adds suspend/resume support so that it is possible to configure the LDOs and BUCKs as on or off during suspend phase as well as to configure suspend specific voltages.

---
 drivers/regulator/pf8x00-regulator.c | 75 ++++++++++++++++++++++++++--
 1 file changed, 70 insertions(+), 5 deletions(-)
drivers/regulator/pf8x00-regulator.c +70 -5
index 1e5582d73405..02892e04acce 100644
@@ -125,8 +125,12 @@ enum pf8x00_devid {
 #define PF8X00_DEVICE_FAM_MASK		GENMASK(7, 4)
 #define PF8X00_DEVICE_ID_MASK		GENMASK(3, 0)
 
-struct pf8x00_regulator {
+struct pf8x00_regulator_data {
 	struct regulator_desc desc;
+	unsigned int suspend_enable_reg;
+	unsigned int suspend_enable_mask;
+	unsigned int suspend_voltage_reg;
+	unsigned int suspend_voltage_cache;
 };
 
 struct pf8x00_chip {
@@ -276,6 +280,53 @@ static int pf8x00_of_parse_cb(struct device_node *np,
 	return 0;
 }
 
+static int pf8x00_suspend_enable(struct regulator_dev *rdev)
+{
+	struct pf8x00_regulator_data *regl = rdev_get_drvdata(rdev);
+	struct regmap *rmap = rdev_get_regmap(rdev);
+
+	return regmap_update_bits(rmap, regl->suspend_enable_reg,
+				  regl->suspend_enable_mask,
+				  regl->suspend_enable_mask);
+}
+
+static int pf8x00_suspend_disable(struct regulator_dev *rdev)
+{
+	struct pf8x00_regulator_data *regl = rdev_get_drvdata(rdev);
+	struct regmap *rmap = rdev_get_regmap(rdev);
+
+	return regmap_update_bits(rmap, regl->suspend_enable_reg,
+				  regl->suspend_enable_mask, 0);
+}
+
+static int pf8x00_set_suspend_voltage(struct regulator_dev *rdev, int uV)
+{
+	struct pf8x00_regulator_data *regl = rdev_get_drvdata(rdev);
+	int ret;
+
+	if (regl->suspend_voltage_cache == uV)
+		return 0;
+
+	ret = regulator_map_voltage_iterate(rdev, uV, uV);
+	if (ret < 0) {
+		dev_err(rdev_get_dev(rdev), "failed to map %i uV\n", uV);
+		return ret;
+	}
+
+	dev_dbg(rdev_get_dev(rdev), "uV: %i, reg: 0x%x, msk: 0x%x, val: 0x%x\n",
+		uV, regl->suspend_voltage_reg, regl->desc.vsel_mask, ret);
+	ret = regmap_update_bits(rdev->regmap, regl->suspend_voltage_reg,
+				 regl->desc.vsel_mask, ret);
+	if (ret < 0) {
+		dev_err(rdev_get_dev(rdev), "failed to set %i uV\n", uV);
+		return ret;
+	}
+
+	regl->suspend_voltage_cache = uV;
+
+	return 0;
+}
+
 static const struct regulator_ops pf8x00_ldo_ops = {
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
@@ -283,6 +334,9 @@ static const struct regulator_ops pf8x00_ldo_ops = {
 	.list_voltage = regulator_list_voltage_table,
 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_suspend_enable = pf8x00_suspend_enable,
+	.set_suspend_disable = pf8x00_suspend_disable,
+	.set_suspend_voltage = pf8x00_set_suspend_voltage,
 };
 
 
@@ -295,6 +349,9 @@ static const struct regulator_ops pf8x00_buck1_6_ops = {
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 	.get_current_limit = regulator_get_current_limit_regmap,
 	.set_current_limit = regulator_set_current_limit_regmap,
+	.set_suspend_enable = pf8x00_suspend_enable,
+	.set_suspend_disable = pf8x00_suspend_disable,
+	.set_suspend_voltage = pf8x00_set_suspend_voltage,
 };
 
 static const struct regulator_ops pf8x00_buck7_ops = {
@@ -306,6 +363,8 @@ static const struct regulator_ops pf8x00_buck7_ops = {
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 	.get_current_limit = regulator_get_current_limit_regmap,
 	.set_current_limit = regulator_set_current_limit_regmap,
+	.set_suspend_enable = pf8x00_suspend_enable,
+	.set_suspend_disable = pf8x00_suspend_disable,
 };
 
 static const struct regulator_ops pf8x00_vsnvs_ops = {
@@ -337,6 +396,9 @@ static const struct regulator_ops pf8x00_vsnvs_ops = {
 			.disable_val = 0x0,			\
 			.enable_mask = 2,			\
 		},						\
+		.suspend_enable_reg = (base) + LDO_CONFIG2,	\
+		.suspend_enable_mask = 1,			\
+		.suspend_voltage_reg = (base) + LDO_STBY_VOLT,	\
 	}
 
 #define PF8X00BUCK(_id, _name, base, voltages)			\
@@ -367,6 +429,9 @@ static const struct regulator_ops pf8x00_vsnvs_ops = {
 			.enable_mask = 0x3,			\
 			.enable_time = 500,			\
 		},						\
+		.suspend_enable_reg = (base) + SW_MODE1,	\
+		.suspend_enable_mask = 0xc,			\
+		.suspend_voltage_reg = (base) + SW_STBY_VOLT,	\
 	}
 
 #define PF8X00BUCK7(_name, base, voltages)			\
@@ -415,7 +480,7 @@ static const struct regulator_ops pf8x00_vsnvs_ops = {
 		},						\
 	}
 
-static struct pf8x00_regulator pf8x00_regulators_data[PF8X00_MAX_REGULATORS] = {
+static struct pf8x00_regulator_data pf8x00_regs_data[PF8X00_MAX_REGULATORS] = {
 	PF8X00LDO(1, "ldo1", PF8X00_LDO_BASE(PF8X00_LDO1), pf8x00_ldo_voltages),
 	PF8X00LDO(2, "ldo2", PF8X00_LDO_BASE(PF8X00_LDO2), pf8x00_ldo_voltages),
 	PF8X00LDO(3, "ldo3", PF8X00_LDO_BASE(PF8X00_LDO3), pf8x00_ldo_voltages),
@@ -500,12 +565,12 @@ static int pf8x00_i2c_probe(struct i2c_client *client)
 	if (ret)
 		return ret;
 
-	for (id = 0; id < ARRAY_SIZE(pf8x00_regulators_data); id++) {
-		struct pf8x00_regulator *data = &pf8x00_regulators_data[id];
+	for (id = 0; id < ARRAY_SIZE(pf8x00_regs_data); id++) {
+		struct pf8x00_regulator_data *data = &pf8x00_regs_data[id];
 		struct regulator_dev *rdev;
 
 		config.dev = chip->dev;
-		config.driver_data = chip;
+		config.driver_data = data;
 		config.regmap = chip->regmap;
 
 		rdev = devm_regulator_register(&client->dev, &data->desc, &config);
#2 lore raw

PATCH 1/1 regulator: pf8x00: set ramp_delay for bucks

This patch sets ramp_delay for bucks to the max value given by the datasheet.

---
 drivers/regulator/pf8x00-regulator.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/regulator/pf8x00-regulator.c +2 -0
index 1e5582d73405..edf5c88bf43e 100644
@@ -351,6 +351,7 @@ static const struct regulator_ops pf8x00_vsnvs_ops = {
 			.type = REGULATOR_VOLTAGE,		\
 			.id = PF8X00_BUCK ## _id,		\
 			.owner = THIS_MODULE,			\
+			.ramp_delay = 19000,			\
 			.linear_ranges = pf8x00_sw1_to_6_voltages, \
 			.n_linear_ranges = \
 				ARRAY_SIZE(pf8x00_sw1_to_6_voltages), \
@@ -381,6 +382,7 @@ static const struct regulator_ops pf8x00_vsnvs_ops = {
 			.type = REGULATOR_VOLTAGE,		\
 			.id = PF8X00_BUCK7,		\
 			.owner = THIS_MODULE,			\
+			.ramp_delay = 19000,			\
 			.volt_table = voltages,			\
 			.vsel_reg = (base) + SW_RUN_VOLT,	\
 			.vsel_mask = 0xff,			\
Signature · 1 line
2.29.2
Reviewed-by on v1 1/1
#3 lore raw

Re: [PATCH] regulator: pf8x00: set ramp_delay for bucks

Quoted 30 lines · Christoph Fritz

This patch sets ramp_delay for bucks to the max value given by the datasheet.

---
 drivers/regulator/pf8x00-regulator.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/regulator/pf8x00-regulator.c +2 -1
index 1e5582d73405..edf5c88bf43e 100644
@@ -351,6 +351,7 @@ static const struct regulator_ops pf8x00_vsnvs_ops = {
                        .type = REGULATOR_VOLTAGE,              \
                        .id = PF8X00_BUCK ## _id,               \
                        .owner = THIS_MODULE,                   \
+                       .ramp_delay = 19000,                    \
                        .linear_ranges = pf8x00_sw1_to_6_voltages, \
                        .n_linear_ranges = \
                                ARRAY_SIZE(pf8x00_sw1_to_6_voltages), \
@@ -381,6 +382,7 @@ static const struct regulator_ops pf8x00_vsnvs_ops = {
                        .type = REGULATOR_VOLTAGE,              \
                        .id = PF8X00_BUCK7,             \
                        .owner = THIS_MODULE,                   \
+                       .ramp_delay = 19000,                    \
                        .volt_table = voltages,                 \
                        .vsel_reg = (base) + SW_RUN_VOLT,       \
                        .vsel_mask = 0xff,                      \
--
Quoted 3 lines

2.29.2

Thanks,

maintainer
#4 lore raw

Re: [PATCH] regulator: pf8x00: set ramp_delay for bucks

In reply to Christoph Fritz
Quoted 2 lines · Christoph Fritz

This patch sets ramp_delay for bucks to the max value given by the datasheet.

Please don't send new patches in reply to old threads, it buries things and makes it much harder to follow what's going on. Start a new thread for new submissions.

maintainer
#5 lore raw
In reply to Christoph Fritz
Quoted 3 lines · Christoph Fritz

This patch adds suspend/resume support so that it is possible to configure the LDOs and BUCKs as on or off during suspend phase as well as to configure suspend specific voltages.

Applied to

https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git for-next

Thanks!

[1/1] regulator: pf8x00: Add suspend support

      commit: 7fefe72b0f8c0d7e63af9810c4dcc88757eddcd5

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

Thanks,
Mark

maintainer
#6 lore raw
In reply to Christoph Fritz
Quoted 3 lines · Christoph Fritz

This patch adds suspend/resume support so that it is possible to configure the LDOs and BUCKs as on or off during suspend phase as well as to configure suspend specific voltages.

Applied to

https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git for-next

Thanks!

[1/1] regulator: pf8x00: Add suspend support

      commit: 7fefe72b0f8c0d7e63af9810c4dcc88757eddcd5

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

Thanks,
Mark