x86: fix hang when AP bringup is too slow
v4 cover x86: fix hang when AP bringup is too slow
changes since v3:
* put simple bugfixes first
* move common part of syncing with master CPU in cpu_init() for x32/64 variant into helper function
* cpu_init(): WARN_ON if cpu_initialized_mask is set
* fix panic on CPU unplug, caused by erroneous removing of "pr->dev = dev;" in drivers/acpi/acpi_processor.c
--
Hang is observed on virtual machines during CPU hotplug, especially in big guests with many CPUs. (It happens more often if host is over-committed).
Hang happens because master CPU timeouts on waiting till AP boots and 'cancels' CPU online operation assuming AP is not functional but AP may continue run wild later causing various hangs or panics in running kernel that is assuming that AP was offline.
This is an alternative approach, that instead of canceling in-progress AP bringup (https://lkml.org/lkml/2014/3/6/257),
removes timeouts so that AP bringup won't be affected by poor timing and syncs AP with master CPU at early startup making sure that AP won't run wild if master CPU doesn't expect AP to come online.
Series also fixes 3 bugs found during testing CPU bringup failure case.
--
Below is the detailed description of a more often happening hang:
---
Master CPU may timeout before cpu_callin_mask is set and cancel booting CPU, but being onlined CPU still continues to boot, sets cpu_active_mask (CPU_STARTING notifiers) and spins in check_tsc_sync_target() for master cpu to arrive. Following attempt to online another cpu hangs in stop_machine, initiated from here:smp_callin ->
smp_store_cpu_info ->
identify_secondary_cpu ->
mtrr_ap_init -> set_mtrr_from_inactive_cpustop_machine waits on completion of stop_work on all CPUs from cpu_active_mask including a failed CPU that spins in check_tsc_sync_target().
Igor Mammedov (5):
x86: fix list corruption on CPU hotplug
x86: fix memory corruption in acpi_unmap_lsapic()
acpi_processor: do not mark present at boot but not onlined CPU as
onlined
x86: log error on secondary CPU wakeup failure at ERR level
x86: initialize secondary CPU only if master CPU will wait for it
arch/x86/kernel/cpu/common.c | 27 ++++++---- arch/x86/kernel/smpboot.c | 103 ++++++++++++---------------------------- drivers/acpi/acpi_processor.c | 1 - 3 files changed, 47 insertions(+), 84 deletions(-)
PATCH v4 1/5 x86: fix list corruption on CPU hotplug
currently if AP wake up is failed, master CPU marks AP as not present in do_boot_cpu() by calling set_cpu_present(cpu, false). That leads to following list corruption on the next physical CPU hotplug:
[ 418.107336] WARNING: CPU: 1 PID: 45 at lib/list_debug.c:33 __list_add+0xbe/0xd0() [ 418.115268] list_add corruption. prev->next should be next (ffff88003dc57600), but was ffff88003e20c3a0. (prev=ffff88003e20c3a0). [ 418.123693] Modules linked in: nf_conntrack_netbios_ns nf_conntrack_broadcast ipt_MASQUERADE ip6t_REJECT ipt_REJECT cfg80211 xt_conntrack rfkill ee [ 418.138979] CPU: 1 PID: 45 Comm: kworker/u10:1 Not tainted 3.14.0-rc6+ #387 [ 418.149989] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2007 [ 418.165750] Workqueue: kacpi_hotplug acpi_hotplug_work_fn [ 418.166433] 0000000000000021 ffff880038ca7988 ffffffff8159b22d 0000000000000021 [ 418.176460] ffff880038ca79d8 ffff880038ca79c8 ffffffff8106942c ffff880038ca79e8 [ 418.177453] ffff88003e20c3a0 ffff88003dc57600 ffff88003e20c3a0 00000000ffffffea [ 418.178445] Call Trace: [ 418.185811] [<ffffffff8159b22d>] dump_stack+0x49/0x5c [ 418.186440] [<ffffffff8106942c>] warn_slowpath_common+0x8c/0xc0 [ 418.187192] [<ffffffff81069516>] warn_slowpath_fmt+0x46/0x50 [ 418.191231] [<ffffffff8136ef51>] ? acpi_ns_get_node+0xb7/0xc7 [ 418.193889] [<ffffffff812f796e>] __list_add+0xbe/0xd0 [ 418.196649] [<ffffffff812e2aa9>] kobject_add_internal+0x79/0x200 [ 418.208610] [<ffffffff812e2e18>] kobject_add_varg+0x38/0x60 [ 418.213831] [<ffffffff812e2ef4>] kobject_add+0x44/0x70 [ 418.229961] [<ffffffff813e2c60>] device_add+0xd0/0x550 [ 418.234991] [<ffffffff813f0e95>] ? pm_runtime_init+0xe5/0xf0 [ 418.250226] [<ffffffff813e32be>] device_register+0x1e/0x30 [ 418.255296] [<ffffffff813e82a3>] register_cpu+0xe3/0x130 [ 418.266539] [<ffffffff81592be5>] arch_register_cpu+0x65/0x150 [ 418.285845] [<ffffffff81355c0d>] acpi_processor_hotadd_init+0x5a/0x9b
...
Which is caused by the fact that generic_processor_info() allocates logical CPU id by calling:
cpu = cpumask_next_zero(-1, cpu_present_mask);
which returns id of previously failed to wake up CPU, since its bit is cleared by do_boot_cpu() and as result register_cpu() tries to register another CPU with the same id as already present but failed to be onlined CPU.
Taking in account that AP will not do anything if master CPU failed to wake it up, there is no reason to mark that AP as not present and break next cpu hotplug attempts. As a side effect of not marking AP as not present, user would be allowed to online it again later.
--- arch/x86/kernel/smpboot.c | 1 - 1 files changed, 0 insertions(+), 1 deletions(-)
arch/x86/kernel/smpboot.c +0 -1
@@ -860,7 +860,6 @@ static int do_boot_cpu(int apicid, int cpu, struct task_struct *idle)/* was set by cpu_init() */ cpumask_clear_cpu (cpu, cpu_initialized_mask); -set_cpu_present (cpu, false);per_cpu (x86_cpu_to_apicid, cpu) =BAD_APICID ; }
Signature · 1 line
1.7.1
Re: [PATCH v4 1/5] x86: fix list corruption on CPU hotplug
Quoted 40 lines · Igor Mammedov
currently if AP wake up is failed, master CPU marks AP as not present in
do_boot_cpu()by callingset_cpu_present(cpu, false). That leads to following list corruption on the next physical CPU hotplug:[ 418.107336] WARNING: CPU: 1 PID: 45 at lib/list_debug.c:33 __list_add+0xbe/0xd0() [ 418.115268] list_add corruption. prev->next should be next (ffff88003dc57600), but was ffff88003e20c3a0. (prev=ffff88003e20c3a0). [ 418.123693] Modules linked in: nf_conntrack_netbios_ns nf_conntrack_broadcast ipt_MASQUERADE ip6t_REJECT ipt_REJECT cfg80211 xt_conntrack rfkill ee [ 418.138979] CPU: 1 PID: 45 Comm: kworker/u10:1 Not tainted 3.14.0-rc6+ #387 [ 418.149989] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2007 [ 418.165750] Workqueue: kacpi_hotplug acpi_hotplug_work_fn [ 418.166433] 0000000000000021 ffff880038ca7988 ffffffff8159b22d 0000000000000021 [ 418.176460] ffff880038ca79d8 ffff880038ca79c8 ffffffff8106942c ffff880038ca79e8 [ 418.177453] ffff88003e20c3a0 ffff88003dc57600 ffff88003e20c3a0 00000000ffffffea [ 418.178445] Call Trace: [ 418.185811] [<ffffffff8159b22d>] dump_stack+0x49/0x5c [ 418.186440] [<ffffffff8106942c>] warn_slowpath_common+0x8c/0xc0 [ 418.187192] [<ffffffff81069516>] warn_slowpath_fmt+0x46/0x50 [ 418.191231] [<ffffffff8136ef51>] ? acpi_ns_get_node+0xb7/0xc7 [ 418.193889] [<ffffffff812f796e>] __list_add+0xbe/0xd0 [ 418.196649] [<ffffffff812e2aa9>] kobject_add_internal+0x79/0x200 [ 418.208610] [<ffffffff812e2e18>] kobject_add_varg+0x38/0x60 [ 418.213831] [<ffffffff812e2ef4>] kobject_add+0x44/0x70 [ 418.229961] [<ffffffff813e2c60>] device_add+0xd0/0x550 [ 418.234991] [<ffffffff813f0e95>] ? pm_runtime_init+0xe5/0xf0 [ 418.250226] [<ffffffff813e32be>] device_register+0x1e/0x30 [ 418.255296] [<ffffffff813e82a3>] register_cpu+0xe3/0x130 [ 418.266539] [<ffffffff81592be5>] arch_register_cpu+0x65/0x150 [ 418.285845] [<ffffffff81355c0d>] acpi_processor_hotadd_init+0x5a/0x9b...
Which is caused by the fact thatgeneric_processor_info()allocates logical CPU id by calling:cpu =
cpumask_next_zero(-1, cpu_present_mask);which returns id of previously failed to wake up CPU, since its bit is cleared by
do_boot_cpu()and as resultregister_cpu()tries to register another CPU with the same id as already present but failed to be onlined CPU.
Quoted 6 lines
Taking in account that AP will not do anything if master CPU failed to wake it up, there is no reason to mark that AP as not present and break next cpu hotplug attempts. As a side effect of not marking AP as not present, user would be allowed to online it again later.
Signed-off-by Igor Mammedov <[email protected]>
Hi Igor,
Sorry for long delay... Can you please combine patch 1/5 and 2/5? When a CPU is marked as present, its APIC ID must be valid. So, it does not make sense to separate patch 1/5 and 2/5. With that change:
Thanks,
-Toshi
PATCH v4 2/5 x86: fix memory corruption in acpi_unmap_lsapic()
In reply to Igor Mammedovif during CPU hotplug master CPU failed to wake up AP it set percpu x86_cpu_to_apicid to BAD_APICID=0xFFFF for AP.
However following attempt to unplug that CPU will lead to out of bound write access to __apicid_to_node[] which is 32768 items long on x86_64 kernel.
So drop setting x86_cpu_to_apicid to BAD_APICID in do_boot_cpu() and allow acpi_processor_remove()->acpi_unmap_lsapic() cleanly remove CPU.
--- arch/x86/kernel/smpboot.c | 2 -- 1 files changed, 0 insertions(+), 2 deletions(-)
arch/x86/kernel/smpboot.c +0 -2
@@ -859,8 +859,6 @@ static int do_boot_cpu(int apicid, int cpu, struct task_struct *idle)/* was set by cpu_init() */ cpumask_clear_cpu (cpu, cpu_initialized_mask); - -per_cpu (x86_cpu_to_apicid, cpu) =BAD_APICID ; }/* mark "stuck" area as not stuck */
Signature · 1 line
1.7.1
PATCH v4 3/5 acpi_processor: do not mark present at boot but not onlined CPU as onlined
In reply to Igor Mammedovacpi_processor_add() assumes that present at boot CPUs are always onlined, it is not so if a CPU failed to become onlined. As result acpi_processor_add() will mark such CPU device as onlined in sysfs and following attempts to online/offline it using /sys/device/system/cpu/cpuX/online attribute will fail.
Do not poke into device internals in acpi_processor_add() and touch "struct device { .offline }" attribute, since for CPUs onlined at boot it's set by:
topology_init() -> arch_register_cpu() -> register_cpu()
before ACPI device tree is parsed, and for hotplugged CPUs it's set when userspace onlines CPU via sysfs.
---
v2:
- fix regression in v1 leading to NULL pointer dereference on CPU unplug, do not remove "pr->dev = dev;"
--- drivers/acpi/acpi_processor.c | 1 - 1 files changed, 0 insertions(+), 1 deletions(-)
drivers/acpi/acpi_processor.c +0 -1
@@ -404,7 +404,6 @@ static int acpi_processor_add(struct acpi_device *device, goto err; pr->dev = dev; - dev->offline = pr->flags.need_hotplug_init;/* Trigger the processor driver's .probe() if present. */ if (device_attach (dev) >=0 )
Signature · 1 line
1.7.1
Re: [PATCH v4 3/5] acpi_processor: do not mark present at boot but not onlined CPU as onlined
Quoted 14 lines · Igor Mammedov
acpi_processor_add()assumes that present at boot CPUs are always onlined, it is not so if a CPU failed to become onlined. As resultacpi_processor_add()will mark such CPU device as onlined in sysfs and following attempts to online/offline it using/sys/device/system/cpu/cpuX/onlineattribute will fail.Do not poke into device internals in
acpi_processor_add()and touch "struct device { .offline }" attribute, since for CPUs onlined at boot it's set by:
topology_init()->arch_register_cpu()->register_cpu()
before ACPI device tree is parsed, and for hotplugged CPUs it's set when userspace onlines CPU via sysfs.
Quoted 5 lines
Signed-off-by Igor Mammedov <[email protected]>---
v2:
- fix regression in v1 leading to NULL pointer dereference on CPU unplug, do not remove "pr->dev= dev;"
Yeah.
Does this patch depend on any other patches in the series?
I don't think so, but just asking.
If it doesn't, why is it part of this series at all?
Quoted 17 lines
--- drivers/acpi/acpi_processor.c | 1 - 1 files changed, 0 insertions(+), 1 deletions(-)drivers/acpi/acpi_processor.c +0
-1@@ -404,7 +404,6 @@ static int acpi_processor_add(struct acpi_device *device, goto err; pr->dev = dev; - dev->offline = pr->flags.need_hotplug_init;/* Trigger the processor driver's .probe() if present. */ if (device_attach (dev) >=0 )
Signature · 2 lines
I speak only for myself. Rafael J. Wysocki, Intel Open Source Technology Center.
Re: [PATCH v4 3/5] acpi_processor: do not mark present at boot but not onlined CPU as onlined
Quoted 21 lines · On Tue, 15 Apr 2014 07:48:30 +0200 "Rafael J. Wysocki" <[email protected]>…
Quoted 14 lines · Igor Mammedov
acpi_processor_add()assumes that present at boot CPUs are always onlined, it is not so if a CPU failed to become onlined. As resultacpi_processor_add()will mark such CPU device as onlined in sysfs and following attempts to online/offline it using/sys/device/system/cpu/cpuX/onlineattribute will fail.Do not poke into device internals in
acpi_processor_add()and touch "struct device { .offline }" attribute, since for CPUs onlined at boot it's set by:
topology_init()->arch_register_cpu()->register_cpu()
before ACPI device tree is parsed, and for hotplugged CPUs it's set when userspace onlines CPU via sysfs.Quoted 5 lines
Signed-off-by Igor Mammedov <[email protected]>---
v2:
- fix regression in v1 leading to NULL pointer dereference on CPU unplug, do not remove "pr->dev= dev;"
Quoted 7 lines
Yeah.
Does this patch depend on any other patches in the series?
I don't think so, but just asking.
If it doesn't, why is it part of this series at all?
It's doesn't depend on any other patches in here, it was just convenient to post it as a part of fixes found in CPU hotplug code and nothing more.
Quoted 19 lines
Quoted 18 lines
--- drivers/acpi/acpi_processor.c | 1 - 1 files changed, 0 insertions(+), 1 deletions(-)drivers/acpi/acpi_processor.c +0
-1@@ -404,7 +404,6 @@ static int acpi_processor_add(struct acpi_device *device, goto err; pr->dev = dev; - dev->offline = pr->flags.need_hotplug_init;/* Trigger the processor driver's .probe() if present. */ if (device_attach (dev) >=0 )
Re: [PATCH v4 3/5] acpi_processor: do not mark present at boot but not onlined CPU as onlined
In reply to Rafael J. WysockiQuoted 21 lines · Rafael J. Wysocki
Quoted 14 lines · Igor Mammedov
acpi_processor_add()assumes that present at boot CPUs are always onlined, it is not so if a CPU failed to become onlined. As resultacpi_processor_add()will mark such CPU device as onlined in sysfs and following attempts to online/offline it using/sys/device/system/cpu/cpuX/onlineattribute will fail.Do not poke into device internals in
acpi_processor_add()and touch "struct device { .offline }" attribute, since for CPUs onlined at boot it's set by:
topology_init()->arch_register_cpu()->register_cpu()
before ACPI device tree is parsed, and for hotplugged CPUs it's set when userspace onlines CPU via sysfs.Quoted 5 lines
Signed-off-by Igor Mammedov <[email protected]>---
v2:
- fix regression in v1 leading to NULL pointer dereference on CPU unplug, do not remove "pr->dev= dev;"
Quoted 7 lines
Yeah.
Does this patch depend on any other patches in the series?
I don't think so, but just asking.
If it doesn't, why is it part of this series at all?
I suspect because Igor was rigorously stress-testing CPU hotplug, and was fixing all the bugs he saw, before adding the one feature he is interested in.
The feature cannot be guaranteed to be correct, without having a stable base to work on.
As such this series makes sense, as long as the fixes precede the feature, and as long as the fixes are correct.
Consider it work in progress, with you being one of the reviewers who makes sure the fixes are correct.
Thanks,
Ingo
Re: [PATCH v4 3/5] acpi_processor: do not mark present at boot but not onlined CPU as onlined
Quoted 36 lines · Ingo Molnar
Quoted 21 lines · Rafael J. Wysocki
Quoted 14 lines · Igor Mammedov
acpi_processor_add()assumes that present at boot CPUs are always onlined, it is not so if a CPU failed to become onlined. As resultacpi_processor_add()will mark such CPU device as onlined in sysfs and following attempts to online/offline it using/sys/device/system/cpu/cpuX/onlineattribute will fail.Do not poke into device internals in
acpi_processor_add()and touch "struct device { .offline }" attribute, since for CPUs onlined at boot it's set by:
topology_init()->arch_register_cpu()->register_cpu()
before ACPI device tree is parsed, and for hotplugged CPUs it's set when userspace onlines CPU via sysfs.Quoted 5 lines
Signed-off-by Igor Mammedov <[email protected]>---
v2:
- fix regression in v1 leading to NULL pointer dereference on CPU unplug, do not remove "pr->dev= dev;"Quoted 7 lines
Yeah.
Does this patch depend on any other patches in the series?
I don't think so, but just asking.
If it doesn't, why is it part of this series at all?
I suspect because Igor was rigorously stress-testing CPU hotplug, and was fixing all the bugs he saw, before adding the one feature he is interested in.
Quoted 8 lines
The feature cannot be guaranteed to be correct, without having a stable base to work on.
As such this series makes sense, as long as the fixes precede the feature, and as long as the fixes are correct.
Consider it work in progress, with you being one of the reviewers who makes sure the fixes are correct.
Fair enough.
So perhaps the subject of the whole series should be changed, because x86 is not the only architecture affected by this particular patch?
Rafael
Re: [PATCH v4 3/5] acpi_processor: do not mark present at boot but not onlined CPU as onlined
In reply to Igor MammedovQuoted 28 lines · Igor Mammedov
acpi_processor_add()assumes that present at boot CPUs are always onlined, it is not so if a CPU failed to become onlined. As resultacpi_processor_add()will mark such CPU device as onlined in sysfs and following attempts to online/offline it using/sys/device/system/cpu/cpuX/onlineattribute will fail.Do not poke into device internals in
acpi_processor_add()and touch "struct device { .offline }" attribute, since for CPUs onlined at boot it's set by:
topology_init()->arch_register_cpu()->register_cpu()
before ACPI device tree is parsed, and for hotplugged CPUs it's set when userspace onlines CPU via sysfs.Signed-off-by Igor Mammedov <[email protected]>---
v2:
- fix regression in v1 leading to NULL pointer dereference on CPU unplug, do not remove "pr->dev= dev;"--- drivers/acpi/acpi_processor.c | 1 - 1 files changed, 0 insertions(+), 1 deletions(-)drivers/acpi/acpi_processor.c +0
-0
drivers/acpi/acpi_processor.c static int acpi_processor_add(struct acpi_device *device, · line 407
Quoted 4 lines
drivers/acpi/acpi_processor.c +0
-1@@ -404,7 +404,6 @@ static int acpi_processor_add(struct acpi_device *device, goto err; pr->dev = dev; - dev->offline = pr->flags.need_hotplug_init;
This line is to ensure that dev->offline and pr->flags.need_hotplug_init are consistent with each other. If you remove it, you need to ensure that they will be consistent in some other way.
Quoted 4 lines
drivers/acpi/acpi_processor.c +0
-0/* Trigger the processor driver's .probe() if present. */ if (device_attach (dev) >=0 )
Signature · 2 lines
I speak only for myself. Rafael J. Wysocki, Intel Open Source Technology Center.
Re: [PATCH v4 3/5] acpi_processor: do not mark present at boot but not onlined CPU as onlined
In reply to Igor MammedovQuoted 28 lines · Igor Mammedov
acpi_processor_add()assumes that present at boot CPUs are always onlined, it is not so if a CPU failed to become onlined. As resultacpi_processor_add()will mark such CPU device as onlined in sysfs and following attempts to online/offline it using/sys/device/system/cpu/cpuX/onlineattribute will fail.Do not poke into device internals in
acpi_processor_add()and touch "struct device { .offline }" attribute, since for CPUs onlined at boot it's set by:
topology_init()->arch_register_cpu()->register_cpu()
before ACPI device tree is parsed, and for hotplugged CPUs it's set when userspace onlines CPU via sysfs.Signed-off-by Igor Mammedov <[email protected]>---
v2:
- fix regression in v1 leading to NULL pointer dereference on CPU unplug, do not remove "pr->dev= dev;"--- drivers/acpi/acpi_processor.c | 1 - 1 files changed, 0 insertions(+), 1 deletions(-)drivers/acpi/acpi_processor.c +0
-0
drivers/acpi/acpi_processor.c static int acpi_processor_add(struct acpi_device *device, · line 407
Quoted 4 lines
drivers/acpi/acpi_processor.c +0
-1@@ -404,7 +404,6 @@ static int acpi_processor_add(struct acpi_device *device, goto err; pr->dev = dev; - dev->offline = pr->flags.need_hotplug_init;
IIRC, this change was necessary to handle the case when maxcpus=X is specified at boot. In this case, excessive CPU's dev->offline needs to be set to 1. Can you verify this?
Thanks,
-Toshi
Re: [PATCH v4 3/5] acpi_processor: do not mark present at boot but not onlined CPU as onlined
Quoted 31 lines · On Wed, 30 Apr 2014 15:25:51 -0600 Toshi Kani <[email protected]> wrote:
Quoted 30 lines · Igor Mammedov
acpi_processor_add()assumes that present at boot CPUs are always onlined, it is not so if a CPU failed to become onlined. As resultacpi_processor_add()will mark such CPU device as onlined in sysfs and following attempts to online/offline it using/sys/device/system/cpu/cpuX/onlineattribute will fail.Do not poke into device internals in
acpi_processor_add()and touch "struct device { .offline }" attribute, since for CPUs onlined at boot it's set by:
topology_init()->arch_register_cpu()->register_cpu()
before ACPI device tree is parsed, and for hotplugged CPUs it's set when userspace onlines CPU via sysfs.Signed-off-by Igor Mammedov <[email protected]>---
v2:
- fix regression in v1 leading to NULL pointer dereference on CPU unplug, do not remove "pr->dev= dev;"--- drivers/acpi/acpi_processor.c | 1 - 1 files changed, 0 insertions(+), 1 deletions(-)drivers/acpi/acpi_processor.c:q renamed from drivers/acpi/acpi_processor.c +0
-0@@ -404,7 +404,6 @@ static int acpi_processor_add(struct acpi_device *device, goto err;
Quoted 6 lines
drivers/acpi/acpi_processor.c:q static int acpi_processor_add(struct acpi_device *device, · line 407
Quoted 2 lines
drivers/acpi/acpi_processor.c:q renamed from drivers/acpi/acpi_processor.c +0
-1pr->dev = dev; - dev->offline = pr->flags.need_hotplug_init;IIRC, this change was necessary to handle the case when maxcpus=X is specified at boot. In this case, excessive CPU's
dev->offlineneeds to be set to 1. Can you verify this?
Option 'maxcpus' works just fine without and with this patch since a bit earlier in acpi_processor_add() it exits in case of extra present CPUs:
#ifdef CONFIG_SMP
if (pr->id >= setup_max_cpus && pr->id != 0)
return 0;#endif
and execution doesn't get to the point the patch touches.
The point is that acpi_processor_add() shouldn't touch dev->offline at all and allow register_cpu() handle it.
Quoted 4 lines
Thanks,
-Toshi
Toshi Kani
Acked-byRe: [PATCH v4 3/5] acpi_processor: do not mark present at boot but not onlined CPU as onlined
Quoted 43 lines · Igor Mammedov
Quoted 31 lines · On Wed, 30 Apr 2014 15:25:51 -0600 Toshi Kani <[email protected]> wrote:
Quoted 30 lines · Igor Mammedov
acpi_processor_add()assumes that present at boot CPUs are always onlined, it is not so if a CPU failed to become onlined. As resultacpi_processor_add()will mark such CPU device as onlined in sysfs and following attempts to online/offline it using/sys/device/system/cpu/cpuX/onlineattribute will fail.Do not poke into device internals in
acpi_processor_add()and touch "struct device { .offline }" attribute, since for CPUs onlined at boot it's set by:
topology_init()->arch_register_cpu()->register_cpu()
before ACPI device tree is parsed, and for hotplugged CPUs it's set when userspace onlines CPU via sysfs.Signed-off-by Igor Mammedov <[email protected]>---
v2:
- fix regression in v1 leading to NULL pointer dereference on CPU unplug, do not remove "pr->dev= dev;"--- drivers/acpi/acpi_processor.c | 1 - 1 files changed, 0 insertions(+), 1 deletions(-)drivers/acpi/acpi_processor.c:q renamed from drivers/acpi/acpi_processor.c +0
-0@@ -404,7 +404,6 @@ static int acpi_processor_add(struct acpi_device *device, goto err;Quoted 6 lines
drivers/acpi/acpi_processor.c:q static int acpi_processor_add(struct acpi_device *device, · line 407
Quoted 2 lines
drivers/acpi/acpi_processor.c:q renamed from drivers/acpi/acpi_processor.c +0
-1pr->dev = dev; - dev->offline = pr->flags.need_hotplug_init;IIRC, this change was necessary to handle the case when maxcpus=X is specified at boot. In this case, excessive CPU's
dev->offlineneeds to be set to 1. Can you verify this?Option 'maxcpus' works just fine without and with this patch since a bit earlier in
acpi_processor_add()it exits in case of extra present CPUs:
Quoted 6 lines
#ifdef CONFIG_SMP if (pr->id >= setup_max_cpus && pr->id != 0) return 0;#endif
and execution doesn't get to the point the patch touches.
This is a separate topic, but I feel that the above code should not be necessary...
Quoted 2 lines
The point is that
acpi_processor_add()shouldn't touchdev->offlineat all and allowregister_cpu()handle it.
Sorry, I had confused with cpu->dev.offline in register_cpu() in my recollection. Yes, I agree that we should let register_cpu() to handle it.
Thanks,
-Toshi
PATCH v4 4/5 x86: log error on secondary CPU wakeup failure at ERR level
In reply to Igor MammedovIf system is running without debug level logging, it will not log error if do_boot_cpu() failed to wakeup AP. It may lead to silent AP bringup failures at boot time.
Change message level to KERN_ERR to make error visible to user as it's done on other architectures.
--- arch/x86/kernel/smpboot.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)
arch/x86/kernel/smpboot.c +1 -1
@@ -918,7 +918,7 @@ int native_cpu_up(unsigned int cpu, struct task_struct *tidle) err =do_boot_cpu (apicid, cpu, tidle);if (err) { -pr_debug ("do_boot_cpu failed %d\n" , err); +pr_err ("do_boot_cpu failed(%d) to wakeup CPU#%u\n" , err, cpu);return -EIO ; }
Signature · 1 line
1.7.1
Re: [PATCH v4 4/5] x86: log error on secondary CPU wakeup failure at ERR level
Quoted 17 lines · Igor Mammedov
If system is running without debug level logging, it will not log error if
do_boot_cpu()failed to wakeup AP. It may lead to silent AP bringup failures at boot time.
Change message level toKERN_ERRto make error visible to user as it's done on other architectures.Signed-off-by Igor Mammedov <[email protected]>--- arch/x86/kernel/smpboot.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)arch/x86/kernel/smpboot.c +0
-0
arch/x86/kernel/smpboot.c int native_cpu_up(unsigned int cpu, struct task_struct *tidle) · line 924
Quoted 8 lines
arch/x86/kernel/smpboot.c +1
-1@@ -918,7 +918,7 @@ int native_cpu_up(unsigned int cpu, struct task_struct *tidle) err =do_boot_cpu (apicid, cpu, tidle);if (err) { -pr_debug ("do_boot_cpu failed %d\n" , err); +pr_err ("do_boot_cpu failed(%d) to wakeup CPU#%u\n" , err, cpu);return -EIO ; }
Looks good.
I will review patch 5/5 later (probably tomorrow). Thanks,
-Toshi
PATCH v4 5/5 x86: initialize secondary CPU only if master CPU will wait for it
In reply to Igor MammedovHang is observed on virtual machines during CPU hotplug, especially in big guests with many CPUs. (It reproducible more often if host is over-committed).
It happens because master CPU gives up waiting on secondary CPU and allows it to run wild. As result AP causes locking or crashing system. For example as described here: https://lkml.org/lkml/2014/3/6/257
If master CPU have sent STARTUP IPI successfully, and AP signalled to master CPU that it's ready to start initialization, make master CPU wait indefinitely till AP is onlined.
To ensure that AP won't ever run wild, make it wait at early startup till master CPU confirms its intention to wait for AP.
---
v2:
- ammend comment in cpu_init()
v3:
- leave timeouts in do_boot_cpu(), so that master CPU won't hang if AP doesn't respond, use cpu_initialized_mask as a way for AP to signal to master CPU that it's ready to start initialzation.
v4:
- move common code in cpu_init() for x32/x64 in shared helper function wait_for_master_cpu()
- add WARN_ON(cpumask_test_and_set_cpu(cpu, cpu_initialized_mask)) to wait_formaster_cpu()
--- arch/x86/kernel/cpu/common.c | 27 +++++++----- arch/x86/kernel/smpboot.c | 98 +++++++++++++----------------------------- 2 files changed, 46 insertions(+), 79 deletions(-)
arch/x86/kernel/cpu/common.c +16 -11
@@ -1221,6 +1221,17 @@ static void dbg_restore_debug_regs(void)#define dbg_restore_debug_regs ()#endif /* ! CONFIG_KGDB */ +static void wait_for_master_cpu (int cpu) +{ +/* +* wait for ACK from master CPU before continuing +* with AP initialization +*/ +WARN_ON (cpumask_test_and_set_cpu (cpu, cpu_initialized_mask)); +while (!cpumask_test_cpu (cpu, cpu_callout_mask)) +cpu_relax (); +} +/* * cpu_init() initializes state that is per-CPU. Some data is already * initialized (naturally) in the bootstrap process, such as the GDT
@@ -1236,16 +1247,17 @@ void cpu_init(void)struct task_struct *me;struct tss_struct *t;unsigned long v; -int cpu; +int cpu =stack_smp_processor_id ();int i; +wait_for_master_cpu (cpu); +/* * Load microcode on this cpu if a valid microcode is available. * This is early microcode loading procedure. */ load_ucode_ap (); - cpu =stack_smp_processor_id (); t = &per_cpu (init_tss, cpu); oist = &per_cpu (orig_ist, cpu);
@@ -1257,9 +1269,6 @@ void cpu_init(void) me = current; -if (cpumask_test_and_set_cpu (cpu, cpu_initialized_mask)) -panic ("CPU#%d already initialized!\n" , cpu); -pr_debug ("Initializing CPU#%d\n" , cpu);clear_in_cr4 (X86_CR4_VME |X86_CR4_PVI |X86_CR4_TSD |X86_CR4_DE );
@@ -1336,13 +1345,9 @@ void cpu_init(void)struct tss_struct *t = &per_cpu (init_tss, cpu);struct thread_struct *thread = &curr->thread; -show_ucode_info_early (); +wait_for_master_cpu (cpu); -if (cpumask_test_and_set_cpu (cpu, cpu_initialized_mask)) { -printk (KERN_WARNING "CPU#%d already initialized!\n" , cpu); -for (;;) -local_irq_enable (); - } +show_ucode_info_early ();printk (KERN_INFO "Initializing CPU#%d\n" , cpu);
arch/x86/kernel/smpboot.c +30 -68
143 lines not on this page · raw message
Signature · 1 line
1.7.1
Re: [PATCH v4 5/5] x86: initialize secondary CPU only if master CPU will wait for it
Quoted 9 lines · Igor Mammedov
Hang is observed on virtual machines during CPU hotplug, especially in big guests with many CPUs. (It reproducible more often if host is over-committed).
It happens because master CPU gives up waiting on secondary CPU and allows it to run wild. As result AP causes locking or crashing system. For example as described here: https://lkml.org/lkml/2014/3/6/257
Quoted 7 lines
If master CPU have sent STARTUP IPI successfully, and AP signalled to master CPU that it's ready to start initialization, make master CPU wait indefinitely till AP is onlined.
To ensure that AP won't ever run wild, make it wait at early startup till master CPU confirms its intention to wait for AP.
Please also add description that the master CPU times out when an AP does not start initialization within 10 seconds.
Quoted 148 lines
Signed-off-by Igor Mammedov <[email protected]>---
v2:
- ammend comment incpu_init()
v3:
- leave timeouts indo_boot_cpu(), so that master CPU won't hang if AP doesn't respond, usecpu_initialized_maskas a way for AP to signal to master CPU that it's ready to start initialzation.
v4:
- move common code incpu_init()for x32/x64 in shared helper functionwait_for_master_cpu()
- addWARN_ON(cpumask_test_and_set_cpu(cpu, cpu_initialized_mask))towait_formaster_cpu()--- arch/x86/kernel/cpu/common.c | 27 +++++++----- arch/x86/kernel/smpboot.c | 98 +++++++++++++----------------------------- 2 files changed, 46 insertions(+), 79 deletions(-)arch/x86/kernel/cpu/common.c +16
-11@@ -1221,6 +1221,17 @@ static void dbg_restore_debug_regs(void)#define dbg_restore_debug_regs ()#endif /* ! CONFIG_KGDB */ +static void wait_for_master_cpu (int cpu) +{ +/* +* wait for ACK from master CPU before continuing +* with AP initialization +*/ +WARN_ON (cpumask_test_and_set_cpu (cpu, cpu_initialized_mask)); +while (!cpumask_test_cpu (cpu, cpu_callout_mask)) +cpu_relax (); +} +/* * cpu_init() initializes state that is per-CPU. Some data is already * initialized (naturally) in the bootstrap process, such as the GDT @@ -1236,16 +1247,17 @@ void cpu_init(void)struct task_struct *me;struct tss_struct *t;unsigned long v; -int cpu; +int cpu =stack_smp_processor_id ();int i; +wait_for_master_cpu (cpu); +/* * Load microcode on this cpu if a valid microcode is available. * This is early microcode loading procedure. */ load_ucode_ap (); - cpu =stack_smp_processor_id (); t = &per_cpu (init_tss, cpu); oist = &per_cpu (orig_ist, cpu);@@ -1257,9 +1269,6 @@ void cpu_init(void) me = current; -if (cpumask_test_and_set_cpu (cpu, cpu_initialized_mask)) -panic ("CPU#%d already initialized!\n" , cpu); -pr_debug ("Initializing CPU#%d\n" , cpu);clear_in_cr4 (X86_CR4_VME |X86_CR4_PVI |X86_CR4_TSD |X86_CR4_DE );@@ -1336,13 +1345,9 @@ void cpu_init(void)struct tss_struct *t = &per_cpu (init_tss, cpu);struct thread_struct *thread = &curr->thread; -show_ucode_info_early (); +wait_for_master_cpu (cpu); -if (cpumask_test_and_set_cpu (cpu, cpu_initialized_mask)) { -printk (KERN_WARNING "CPU#%d already initialized!\n" , cpu); -for (;;) -local_irq_enable (); - } +show_ucode_info_early ();printk (KERN_INFO "Initializing CPU#%d\n" , cpu);arch/x86/kernel/smpboot.c +1
-33@@ -111,7 +111,6 @@ atomic_t init_deasserted;static void smp_callin (void ) {int cpuid, phys_id; -unsigned long timeout;/* * If waken up by an INIT in an 82489DX configuration @@ -130,37 +129,6 @@ static void smp_callin(void)* (This works even if the APIC is not enabled.) */ phys_id =read_apic_id (); -if (cpumask_test_cpu (cpuid, cpu_callin_mask)) { -panic ("%s: phys CPU#%d, CPU#%d already present??\n" , __func__, - phys_id, cpuid); - } -pr_debug ("CPU#%d (phys ID: %d) waiting for CALLOUT\n" , cpuid, phys_id); - -/* -* STARTUP IPIs are fragile beasts as they might sometimes -* trigger some glue motherboard logic. Complete APIC bus -* silence for 1 second, this overestimates the time the -* boot CPU is spending to send the up to 2 STARTUP IPIs -* by a factor of two. This should be enough. -*/ - -/* -* Waiting 2s total for startup (udelay is not yet working) -*/ - timeout = jiffies +2 *HZ ; -while (time_before (jiffies, timeout)) { -/* -* Has the boot CPU finished it's STARTUP sequence? -*/ -if (cpumask_test_cpu (cpuid, cpu_callout_mask)) -break ; -cpu_relax (); - } - -if (!time_before (jiffies, timeout)) { -panic ("%s: CPU%d started up but did not get a callout!\n" , - __func__, cpuid); - }/* * the boot CPU has finished the init stage and is spinning @@ -750,8 +718,8 @@ static int do_boot_cpu(int apicid, int cpu, struct task_struct *idle)unsigned long start_ip = real_mode_header->trampoline_start;unsigned long boot_error =0 ; -int timeout;int cpu0_nmi_registered =0 ; +unsigned long timeout;/* Just in case we booted with a single CPU. */ alternatives_enable_smp ();
arch/x86/kernel/smpboot.c static int do_boot_cpu(int apicid, int cpu, struct task_struct *idle) · line 775
Quoted 9 lines
arch/x86/kernel/smpboot.c +6
-0@@ -799,6 +767,14 @@ static int do_boot_cpu(int apicid, int cpu, struct task_struct *idle) }/* +* AP might wait on cpu_callout_mask in cpu_init() with +* cpu_initialized_mask set if previous attempt to online +* it timed-out. Clear cpu_initialized_mask so that after +* INIT/SIPI it could start with a clean state. +*/ +cpumask_clear_cpu (cpu, cpu_initialized_mask);
I think smp_mb() should be added here to ensure that the target AP sees this change.
Quoted 23 lines
arch/x86/kernel/smpboot.c +9
-4+ +/* * Wake up a CPU in difference cases: * - Use the method in the APIC driver if it's defined * Otherwise, @@ -810,55 +786,41 @@ static int do_boot_cpu(int apicid, int cpu, struct task_struct *idle) boot_error =wakeup_cpu_via_init_nmi (cpu, start_ip, apicid, &cpu0_nmi_registered); +if (!boot_error) {/* -* allow APs to start initializing. +* Wait 10s total for a response from AP */ -pr_debug ("Before Callout %d\n" , cpu); -cpumask_set_cpu (cpu, cpu_callout_mask); -pr_debug ("After Callout %d\n" , cpu); + boot_error =-1 ; + timeout = jiffies +10 *HZ ; +while (time_before (jiffies, timeout)) { +if (cpumask_test_cpu (cpu, cpu_initialized_mask)) { +/*
arch/x86/kernel/smpboot.c static int do_boot_cpu(int apicid, int cpu, struct task_struct *idle) · line 808
Quoted 10 lines
arch/x86/kernel/smpboot.c +10
-0+* Tell AP to proceed with initialization +*/ +cpumask_set_cpu (cpu, cpu_callout_mask); + boot_error =0 ; +break ; + } +udelay (100 ); +schedule (); + } + }
When 10s passed, the master could set a new flag, ex. cpu_callout_error_mask, which wait_for_master_cpu() checks and call play_dead() when it is set. This avoids AP to spin forever when 10s becomes not long enough. But it does not have to be part of this patchset, though.
arch/x86/kernel/smpboot.c static int do_boot_cpu(int apicid, int cpu, struct task_struct *idle) · line 812
Quoted 4 lines
arch/x86/kernel/smpboot.c +2
-1+if (!boot_error) {/* -* Wait 5s total for a response +* Wait till AP completes initial initialization
We should generally avoid such wait w/o a timeout condition, but since native_cpu_up() waits till cpu_online(cpu) anyway after this point, this seems OK... I wonder if we need touch_nmi_watchdog(), though.
Thanks,
-Toshi
Re: [PATCH v4 5/5] x86: initialize secondary CPU only if master CPU will wait for it
Quoted 18 lines · On Thu, 01 May 2014 17:11:56 -0600 Toshi Kani <[email protected]> wrote:
Quoted 9 lines · Igor Mammedov
Hang is observed on virtual machines during CPU hotplug, especially in big guests with many CPUs. (It reproducible more often if host is over-committed).
It happens because master CPU gives up waiting on secondary CPU and allows it to run wild. As result AP causes locking or crashing system. For example as described here: https://lkml.org/lkml/2014/3/6/257
Quoted 7 lines
If master CPU have sent STARTUP IPI successfully, and AP signalled to master CPU that it's ready to start initialization, make master CPU wait indefinitely till AP is onlined.
To ensure that AP won't ever run wild, make it wait at early startup till master CPU confirms its intention to wait for AP.
Quoted 2 lines
Please also add description that the master CPU times out when an AP does not start initialization within 10 seconds.
added
Quoted 151 lines
Quoted 151 lines
Signed-off-by Igor Mammedov <[email protected]>---
v2:
- ammend comment incpu_init()
v3:
- leave timeouts indo_boot_cpu(), so that master CPU won't hang if AP doesn't respond, usecpu_initialized_maskas a way for AP to signal to master CPU that it's ready to start initialzation.
v4:
- move common code incpu_init()for x32/x64 in shared helper functionwait_for_master_cpu()
- addWARN_ON(cpumask_test_and_set_cpu(cpu, cpu_initialized_mask))towait_formaster_cpu()--- arch/x86/kernel/cpu/common.c | 27 +++++++----- arch/x86/kernel/smpboot.c | 98 +++++++++++++----------------------------- 2 files changed, 46 insertions(+), 79 deletions(-)arch/x86/kernel/cpu/common.c +16
-11@@ -1221,6 +1221,17 @@ static void dbg_restore_debug_regs(void)#define dbg_restore_debug_regs ()#endif /* ! CONFIG_KGDB */ +static void wait_for_master_cpu (int cpu) +{ +/* +* wait for ACK from master CPU before continuing +* with AP initialization +*/ +WARN_ON (cpumask_test_and_set_cpu (cpu, cpu_initialized_mask)); +while (!cpumask_test_cpu (cpu, cpu_callout_mask)) +cpu_relax (); +} +/* * cpu_init() initializes state that is per-CPU. Some data is already * initialized (naturally) in the bootstrap process, such as the GDT @@ -1236,16 +1247,17 @@ void cpu_init(void)struct task_struct *me;struct tss_struct *t;unsigned long v; -int cpu; +int cpu =stack_smp_processor_id ();int i; +wait_for_master_cpu (cpu); +/* * Load microcode on this cpu if a valid microcode is available. * This is early microcode loading procedure. */ load_ucode_ap (); - cpu =stack_smp_processor_id (); t = &per_cpu (init_tss, cpu); oist = &per_cpu (orig_ist, cpu);@@ -1257,9 +1269,6 @@ void cpu_init(void) me = current; -if (cpumask_test_and_set_cpu (cpu, cpu_initialized_mask)) -panic ("CPU#%d already initialized!\n" , cpu); -pr_debug ("Initializing CPU#%d\n" , cpu);clear_in_cr4 (X86_CR4_VME |X86_CR4_PVI |X86_CR4_TSD |X86_CR4_DE );@@ -1336,13 +1345,9 @@ void cpu_init(void)struct tss_struct *t = &per_cpu (init_tss, cpu);struct thread_struct *thread = &curr->thread; -show_ucode_info_early (); +wait_for_master_cpu (cpu); -if (cpumask_test_and_set_cpu (cpu, cpu_initialized_mask)) { -printk (KERN_WARNING "CPU#%d already initialized!\n" , cpu); -for (;;) -local_irq_enable (); - } +show_ucode_info_early ();printk (KERN_INFO "Initializing CPU#%d\n" , cpu);arch/x86/kernel/smpboot.c +1
-33@@ -111,7 +111,6 @@ atomic_t init_deasserted;static void smp_callin (void ) {int cpuid, phys_id; -unsigned long timeout;/* * If waken up by an INIT in an 82489DX configuration @@ -130,37 +129,6 @@ static void smp_callin(void)* (This works even if the APIC is not enabled.) */ phys_id =read_apic_id (); -if (cpumask_test_cpu (cpuid, cpu_callin_mask)) { -panic ("%s: phys CPU#%d, CPU#%d already present??\n" , __func__, - phys_id, cpuid); - } -pr_debug ("CPU#%d (phys ID: %d) waiting for CALLOUT\n" , cpuid, phys_id); - -/* -* STARTUP IPIs are fragile beasts as they might sometimes -* trigger some glue motherboard logic. Complete APIC bus -* silence for 1 second, this overestimates the time the -* boot CPU is spending to send the up to 2 STARTUP IPIs -* by a factor of two. This should be enough. -*/ - -/* -* Waiting 2s total for startup (udelay is not yet working) -*/ - timeout = jiffies +2 *HZ ; -while (time_before (jiffies, timeout)) { -/* -* Has the boot CPU finished it's STARTUP sequence? -*/ -if (cpumask_test_cpu (cpuid, cpu_callout_mask)) -break ; -cpu_relax (); - } - -if (!time_before (jiffies, timeout)) { -panic ("%s: CPU%d started up but did not get a callout!\n" , - __func__, cpuid); - }/* * the boot CPU has finished the init stage and is spinning @@ -750,8 +718,8 @@ static int do_boot_cpu(int apicid, int cpu, struct task_struct *idle)unsigned long start_ip = real_mode_header->trampoline_start;unsigned long boot_error =0 ; -int timeout;int cpu0_nmi_registered =0 ; +unsigned long timeout;/* Just in case we booted with a single CPU. */ alternatives_enable_smp ();@@ -799,6 +767,14 @@ static int do_boot_cpu(int apicid, int cpu, struct task_struct *idle) }
Quoted 10 lines
arch/x86/kernel/smpboot.c static int do_boot_cpu(int apicid, int cpu, struct task_struct *idle) · line 775
Quoted 7 lines
arch/x86/kernel/smpboot.c +6
-0/* +* AP might wait on cpu_callout_mask in cpu_init() with +* cpu_initialized_mask set if previous attempt to online +* it timed-out. Clear cpu_initialized_mask so that after +* INIT/SIPI it could start with a clean state. +*/ +cpumask_clear_cpu (cpu, cpu_initialized_mask);I think
smp_mb()should be added here to ensure that the target AP sees this change.
ok
Quoted 32 lines
Quoted 32 lines
arch/x86/kernel/smpboot.c +17
-4+ +/* * Wake up a CPU in difference cases: * - Use the method in the APIC driver if it's defined * Otherwise, @@ -810,55 +786,41 @@ static int do_boot_cpu(int apicid, int cpu, struct task_struct *idle) boot_error =wakeup_cpu_via_init_nmi (cpu, start_ip, apicid, &cpu0_nmi_registered); +if (!boot_error) {/* -* allow APs to start initializing. +* Wait 10s total for a response from AP */ -pr_debug ("Before Callout %d\n" , cpu); -cpumask_set_cpu (cpu, cpu_callout_mask); -pr_debug ("After Callout %d\n" , cpu); + boot_error =-1 ; + timeout = jiffies +10 *HZ ; +while (time_before (jiffies, timeout)) { +if (cpumask_test_cpu (cpu, cpu_initialized_mask)) { +/* +* Tell AP to proceed with initialization +*/ +cpumask_set_cpu (cpu, cpu_callout_mask); + boot_error =0 ; +break ; + } +udelay (100 ); +schedule ();
Quoted 8 lines
arch/x86/kernel/smpboot.c static int do_boot_cpu(int apicid, int cpu, struct task_struct *idle) · line 808
Quoted 2 lines
arch/x86/kernel/smpboot.c +2
-0+ } + }When 10s passed, the master could set a new flag, ex.
cpu_callout_error_mask, whichwait_for_master_cpu()checks and callplay_dead()when it is set. This avoids AP to spin forever when 10s becomes not long enough. But it does not have to be part of this patchset, though.
I'm reluctant to add another to already too many cpu_*_mask, maybe we could reuse cpu_initialized_mask by clearing it on timeout. This way AP spinning on cpu_callout_mask could notice it and halt itself.
It would be better to make it separate patch on top of this series, to reduce delay of bugfixes in this series.
Quoted 8 lines
arch/x86/kernel/smpboot.c static int do_boot_cpu(int apicid, int cpu, struct task_struct *idle) · line 812
Quoted 5 lines
arch/x86/kernel/smpboot.c +2
-1+if (!boot_error) {/* -* Wait 5s total for a response +* Wait till AP completes initial initialization We should generally avoid such wait w/o a timeout condition, but since
native_cpu_up()waits tillcpu_online(cpu)anyway after this point, this
If we don't wait here and fall through into tight loop waiting on cpu_online(cpu) in native_cpu_up() or check_tsc_sync_source() then stop_task for syncing MTTRs initiated from AP won't have a chance to run on the master CPU.
Quoted 1 line
seems OK... I wonder if we need
touch_nmi_watchdog(), though.
There wasn't any touch_nmi_watchdog() in the original code and I don't think we need it here since we are not just spinning on CPU but giving control back to kernel calling schedule(), which would allow watchdog_task to do the job if needed.
Quoted 4 lines
Thanks,
-Toshi
Re: [PATCH v4 5/5] x86: initialize secondary CPU only if master CPU will wait for it
Quoted 2 lines · Igor Mammedov
On Thu, 01 May 2014 17:11:56 -0600
Toshi Kani <[email protected]> wrote:
:
Quoted 8 lines
Quoted 5 lines
When 10s passed, the master could set a new flag, ex.
cpu_callout_error_mask, whichwait_for_master_cpu()checks and callplay_dead()when it is set. This avoids AP to spin forever when 10s becomes not long enough. But it does not have to be part of this patchset, though.I'm reluctant to add another to already too many cpu_*_mask, maybe we could reuse
cpu_initialized_maskby clearing it on timeout. This way AP spinning oncpu_callout_maskcould notice it and halt itself.
I agree that there are too many cpu_* masks. IMHO, these cpu rendezvous masks, initialized/callout/callin, should be combined into a per-cpu flag. There is not much point of being individual masks.
Anyway, I do not think cpu_initialized_mask can be reused here.
Quoted 2 lines
It would be better to make it separate patch on top of this series, to reduce delay of bugfixes in this series.
Agreed.
Quoted 13 lines
Quoted 8 lines
arch/x86/kernel/smpboot.c static int do_boot_cpu(int apicid, int cpu, struct task_struct *idle) · line 812
Quoted 5 lines
arch/x86/kernel/smpboot.c +2
-1+if (!boot_error) {/* -* Wait 5s total for a response +* Wait till AP completes initial initialization We should generally avoid such wait w/o a timeout condition, but since
native_cpu_up()waits tillcpu_online(cpu)anyway after this point, thisIf we don't wait here and fall through into tight loop waiting on
cpu_online(cpu)innative_cpu_up()orcheck_tsc_sync_source()thenstop_taskfor syncing MTTRs initiated from AP won't have a chance to run on the master CPU.
Quoted 5 lines
Quoted 1 line
seems OK... I wonder if we need
touch_nmi_watchdog(), though.There wasn't any
touch_nmi_watchdog()in the original code and I don't think we need it here since we are not just spinning on CPU but giving control back to kernel callingschedule(), which would allowwatchdog_taskto do the job if needed.
Agreed.
Thanks,
-Toshi
Re: [PATCH v4 5/5] x86: initialize secondary CPU only if master CPU will wait for it
Quoted 13 lines · On Fri, 02 May 2014 08:52:22 -0600 Toshi Kani <[email protected]> wrote:
Quoted 2 lines · Igor Mammedov
On Thu, 01 May 2014 17:11:56 -0600
Toshi Kani <[email protected]> wrote::
Quoted 8 lines
Quoted 5 lines
When 10s passed, the master could set a new flag, ex.
cpu_callout_error_mask, whichwait_for_master_cpu()checks and callplay_dead()when it is set. This avoids AP to spin forever when 10s becomes not long enough. But it does not have to be part of this patchset, though.I'm reluctant to add another to already too many cpu_*_mask, maybe we could reuse
cpu_initialized_maskby clearing it on timeout. This way AP spinning oncpu_callout_maskcould notice it and halt itself.
Quoted 5 lines
I agree that there are too many cpu_* masks. IMHO, these cpu rendezvous masks, initialized/callout/callin, should be combined into a per-cpu flag. There is not much point of being individual masks.
Anyway, I do not think
cpu_initialized_maskcan be reused here.
I'll look if we could use percpu here when writing patch to halt timed-out AP.
Quoted 30 lines
Quoted 3 lines
It would be better to make it separate patch on top of this series, to reduce delay of bugfixes in this series.
Agreed.
Quoted 13 lines
Quoted 8 lines
arch/x86/kernel/smpboot.c static int do_boot_cpu(int apicid, int cpu, struct task_struct *idle) · line 812
Quoted 5 lines
arch/x86/kernel/smpboot.c +2
-1+if (!boot_error) {/* -* Wait 5s total for a response +* Wait till AP completes initial initialization We should generally avoid such wait w/o a timeout condition, but since
native_cpu_up()waits tillcpu_online(cpu)anyway after this point, thisIf we don't wait here and fall through into tight loop waiting on
cpu_online(cpu)innative_cpu_up()orcheck_tsc_sync_source()thenstop_taskfor syncing MTTRs initiated from AP won't have a chance to run on the master CPU.Quoted 5 lines
Quoted 1 line
seems OK... I wonder if we need
touch_nmi_watchdog(), though.There wasn't any
touch_nmi_watchdog()in the original code and I don't think we need it here since we are not just spinning on CPU but giving control back to kernel callingschedule(), which would allowwatchdog_taskto do the job if needed.Agreed.
Thanks,
-Toshi
Signature · 2 lines
Regards, Igor
Quoted 7 lines · On Mon, 14 Apr 2014 17:11:12 +0200 Igor Mammedov <[email protected]> wrote:
changes since v3:
* put simple bugfixes first
* move common part of syncing with master CPU incpu_init()for x32/64 variant into helper function
*cpu_init():WARN_ONifcpu_initialized_maskis set
* fix panic on CPU unplug, caused by erroneous removing of "pr->dev= dev;" indrivers/acpi/acpi_processor.c
Hi guys,
It seems there won't be more comments on series,
could you review it, please?
Quoted 52 lines
--
Hang is observed on virtual machines during CPU hotplug, especially in big guests with many CPUs. (It happens more often if host is over-committed).Hang happens because master CPU timeouts on waiting till AP boots and 'cancels' CPU online operation assuming AP is not functional but AP may continue run wild later causing various hangs or panics in running kernel that is assuming that AP was offline.
This is an alternative approach, that instead of canceling in-progress AP bringup (https://lkml.org/lkml/2014/3/6/257),
removes timeouts so that AP bringup won't be affected by poor timing and syncs AP with master CPU at early startup making sure that AP won't run wild if master CPU doesn't expect AP to come online.Series also fixes 3 bugs found during testing CPU bringup failure case.
--
Below is the detailed description of a more often happening hang:
---
Master CPU may timeout beforecpu_callin_maskis set and cancel booting CPU, but being onlined CPU still continues to boot, setscpu_active_mask(CPU_STARTINGnotifiers) and spins incheck_tsc_sync_target()for master cpu to arrive. Following attempt to online another cpu hangs instop_machine, initiated from here:smp_callin->
smp_store_cpu_info->identify_secondary_cpu -> mtrr_ap_init -> set_mtrr_from_inactive_cpu
stop_machinewaits on completion ofstop_workon all CPUs fromcpu_active_maskincluding a failed CPU that spins incheck_tsc_sync_target().Igor Mammedov (5):
x86: fix list corruption on CPU hotplug
x86: fix memory corruption inacpi_unmap_lsapic()
acpi_processor: do not mark present at boot but not onlined CPU as
onlined
x86: log error on secondary CPU wakeup failure at ERR level
x86: initialize secondary CPU only if master CPU will wait for itarch/x86/kernel/cpu/common.c | 27 ++++++---- arch/x86/kernel/smpboot.c | 103 ++++++++++++---------------------------- drivers/acpi/acpi_processor.c | 1 - 3 files changed, 47 insertions(+), 84 deletions(-)
Signature · 2 lines
Regards, Igor