net: eqos: Add PHY reset control for i.MX platform
PATCH 1/9 net: eqos: Add PHY reset control for i.MX platform
Parse the "phy-reset-gpios", "phy-reset-post-delay" and "phy-reset-duration" properties from eqos node to control the ethernet PHY reset at driver probe.
Reset PHY once is enough that can reduce the time cost to get IP after the first time.
--- drivers/net/dwc_eth_qos.c | 55 +++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 55 insertions(+)
drivers/net/dwc_eth_qos.c +55 -0
@@ -303,6 +303,8 @@ struct eqos_priv {struct eqos_tegra186_regs *tegra186_regs;struct reset_ctl reset_ctl;struct gpio_desc phy_reset_gpio; +uint32_t reset_delay; +uint32_t reset_post_delay;struct clk clk_master_bus;struct clk clk_rx;struct clk clk_ptp_ref;
@@ -1880,6 +1882,7 @@ static int eqos_probe_resources_imx(struct udevice *dev) {struct eqos_priv *eqos =dev_get_priv (dev);phy_interface_t interface; +int ret =0 ;debug ("%s(dev=%p):\n" , __func__, dev);
@@ -1890,8 +1893,52 @@ static int eqos_probe_resources_imx(struct udevice *dev)return -EINVAL ; } + ret =gpio_request_by_name (dev,"phy-reset-gpios" ,0 , + &eqos->phy_reset_gpio, +GPIOD_IS_OUT |GPIOD_IS_OUT_ACTIVE ); +if (ret) { +pr_debug ("gpio_request_by_name(phy reset) failed: %d" , ret); + } + +if (dm_gpio_is_valid (&eqos->phy_reset_gpio)) { + eqos->reset_delay =dev_read_u32_default (dev,"phy-reset-duration" ,1 ); +if (eqos->reset_delay >1000 ) { +pr_err ("phy reset duration should be <= 1000ms\n" ); +/* property value wrong, use default value */ + eqos->reset_delay =1 ; + } + +mdelay (eqos->reset_delay); + + eqos->reset_post_delay =dev_read_u32_default (dev, +"phy-reset-post-delay" , +0 ); +if (eqos->reset_post_delay >1000 ) { +pr_err ("phy reset post delay should be <= 1000ms\n" ); +/* property value wrong, use default value */ + eqos->reset_post_delay =0 ; + } + + ret =dm_gpio_set_value (&eqos->phy_reset_gpio,0 ); +if (ret <0 ) { +pr_err ("dm_gpio_set_value(phy_reset, deassert) failed: %d" , ret); + goto err_free_gpio_phy_reset; + } + +if (eqos->reset_post_delay) +mdelay (eqos->reset_post_delay); + } +debug ("%s: OK\n" , __func__);return 0 ; + +err_free_gpio_phy_reset: +if (dm_gpio_is_valid (&eqos->phy_reset_gpio)) { +dm_gpio_free (dev, &eqos->phy_reset_gpio); + } + +debug ("%s: returns %d\n" , __func__, ret); +return ret; }static phy_interface_t eqos_get_interface_imx (struct udevice *dev)
@@ -1951,6 +1998,14 @@ static int eqos_remove_resources_stm32(struct udevice *dev)static int eqos_remove_resources_imx (struct udevice *dev) { +struct eqos_priv *eqos =dev_get_priv (dev); + +debug ("%s(dev=%p):\n" , __func__, dev); +if (dm_gpio_is_valid (&eqos->phy_reset_gpio)) { +dm_gpio_free (dev, &eqos->phy_reset_gpio); + } + +debug ("%s: OK\n" , __func__);return 0 ; }
Signature · 1 line
2.7.4
PATCH 2/9 arm: mach-imx: Update MAC fuse for i.MX8MP
i.MX8MP has two ENET controllers, have to update the function to enable loading two MAC addresses.
--- arch/arm/mach-imx/mac.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-imx/mac.c +1 -1
@@ -31,7 +31,7 @@ void imx_get_mac_from_fuse(int dev_id, unsigned char *mac) offset =is_mx6 () ?MAC_FUSE_MX6_OFFSET :MAC_FUSE_MX7_OFFSET ; fuse = (struct imx_mac_fuse *)(ulong)(OCOTP_BASE_ADDR + offset); - has_second_mac =is_mx7 () ||is_mx6sx () ||is_mx6ul () ||is_mx6ull (); + has_second_mac =is_mx7 () ||is_mx6sx () ||is_mx6ul () ||is_mx6ull () ||is_imx8mp ();if (has_second_mac && dev_id ==1 ) {u32 value =readl (&fuse->mac_addr2);
Signature · 1 line
2.7.4
PATCH 3/9 arm: mach-imx: Allow to build mac.c for EQoS driver
In reply to Ye Lii.MX8MP has one DWC EQoS controller, so allow to build mac.c when only this driver is enabled.
--- arch/arm/mach-imx/Makefile | 1 + 1 file changed, 1 insertion(+)
arch/arm/mach-imx/Makefile +1 -0
@@ -15,6 +15,7 @@ obj-$(CONFIG_IMX_BOOTAUX) += imx_bootaux.o endif obj-$(CONFIG_ENV_IS_IN_MMC) += mmc_env.o obj-$(CONFIG_FEC_MXC) += mac.o +obj-$(CONFIG_DWC_ETH_QOS) += mac.o obj-$(CONFIG_SYS_I2C_MXC) += i2c-mxv7.o obj-y += cpu.o endif
Signature · 1 line
2.7.4
PATCH 4/9 arm: dts: imx8mp: Add EQoS controller node
In reply to Ye LiAdd node for EQoS ethernet controller as the second ethernet port on i.MX8MP
--- arch/arm/dts/imx8mp.dtsi | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)
arch/arm/dts/imx8mp.dtsi +23 -0
@@ -18,6 +18,7 @@ aliases { ethernet0 = &fec; + ethernet1 = &eqos; gpio0 = &gpio1; gpio1 = &gpio2; gpio2 = &gpio3;
@@ -771,6 +772,28 @@ fsl,num-rx-queues = <3>; status = "disabled"; }; + + eqos: ethernet at 30bf0000 { + compatible = "nxp,imx8mp-dwmac-eqos", "snps,dwmac-5.10a"; + reg = <0x30bf0000 0x10000>; + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "eth_wake_irq", "macirq"; + clocks = <&clk IMX8MP_CLK_ENET_QOS_ROOT>, + <&clk IMX8MP_CLK_QOS_ENET_ROOT>, + <&clk IMX8MP_CLK_ENET_QOS_TIMER>, + <&clk IMX8MP_CLK_ENET_QOS>; + clock-names = "stmmaceth", "pclk", "ptp_ref", "tx"; + assigned-clocks = <&clk IMX8MP_CLK_ENET_AXI>, + <&clk IMX8MP_CLK_ENET_QOS_TIMER>, + <&clk IMX8MP_CLK_ENET_QOS>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>, + <&clk IMX8MP_SYS_PLL2_100M>, + <&clk IMX8MP_SYS_PLL2_125M>; + assigned-clock-rates = <0>, <100000000>, <125000000>; + intf_mode = <&gpr 0x4>; + status = "disabled"; + }; }; gic: interrupt-controller at 38800000 {
Signature · 1 line
2.7.4
PATCH 5/9 arm: dts: imx8mp-evk: Enable the EQoS ethernet port
In reply to Ye Lii.MX8MP EVK has two ethernet ports. Add relevant nodes and properties for EQoS port to the EVK DTS file.
In -u-boot.dtsi, change the u-boot eqos compatible string, add PHY reset gpio and remove assigned clocks as not supported in CCF.
--- arch/arm/dts/imx8mp-evk-u-boot.dtsi | 11 ++++++++++ arch/arm/dts/imx8mp-evk.dts | 40 +++++++++++++++++++++++++++++++++++++ 2 files changed, 51 insertions(+)
arch/arm/dts/imx8mp-evk-u-boot.dtsi +11 -0
@@ -140,6 +140,17 @@ u-boot,dm-spl; }; +&eqos { + compatible = "fsl,imx-eqos"; + /delete-property/ assigned-clocks; + /delete-property/ assigned-clock-parents; + /delete-property/ assigned-clock-rates; + + phy-reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>; + phy-reset-duration = <15>; + phy-reset-post-delay = <100>; +}; + &fec { phy-reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>; phy-reset-duration = <15>;
arch/arm/dts/imx8mp-evk.dts +40 -0
@@ -74,6 +74,26 @@ status = "okay"; }; +&eqos { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eqos>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + status = "okay"; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy at 1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + eee-broken-1000t; + }; + }; +}; + &flexcan2 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flexcan2>;
@@ -160,6 +180,26 @@ }; &iomuxc { + pinctrl_eqos: eqosgrp { + fsl,pins = < + MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x3 + MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x3 + MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x91 + MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x91 + MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x91 + MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x91 + MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x91 + MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x91 + MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x1f + MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x1f + MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x1f + MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x1f + MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x1f + MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x1f + MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22 0x19 + >; + }; + pinctrl_fec: fecgrp { fsl,pins = < MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3
Signature · 1 line
2.7.4
PATCH 6/9 imx8mp_evk: Fix incorrect cascade for FEC and EQOS setup
In reply to Ye LiThe setup functions should be independent for two ethernet controllers
--- board/freescale/imx8mp_evk/imx8mp_evk.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
board/freescale/imx8mp_evk/imx8mp_evk.c +3 -2
@@ -101,9 +101,10 @@ int board_init(void)if (CONFIG_IS_ENABLED (FEC_MXC )) {setup_fec (); + } -if (CONFIG_IS_ENABLED (DWC_ETH_QOS )) - ret =setup_eqos (); +if (CONFIG_IS_ENABLED (DWC_ETH_QOS )) { + ret =setup_eqos (); }return ret;
Signature · 1 line
2.7.4
PATCH 7/9 imx8mp_evk: Remove EQoS PHY reset codes
In reply to Ye LiSince we uses the DTS and PHY reset gpio in EQoS driver to do the reset, remove the duplicated codes from board file.
--- board/freescale/imx8mp_evk/imx8mp_evk.c | 19 ------------------- 1 file changed, 19 deletions(-)
board/freescale/imx8mp_evk/imx8mp_evk.c +0 -19
@@ -54,30 +54,11 @@ static void setup_fec(void)setbits_le32 (&gpr->gpr[1 ],BIT (22 )); } -#define EQOS_RST_PAD IMX_GPIO_NR(4, 22) -static iomux_v3_cfg_t const eqos_rst_pads[] = { -MX8MP_PAD_SAI2_RXC__GPIO4_IO22 |MUX_PAD_CTRL (NO_PAD_CTRL ), -}; - -static void setup_iomux_eqos (void ) -{ -imx_iomux_v3_setup_multiple_pads (eqos_rst_pads, -ARRAY_SIZE (eqos_rst_pads)); - -gpio_request (EQOS_RST_PAD ,"eqos_rst" ); -gpio_direction_output (EQOS_RST_PAD ,0 ); -mdelay (15 ); -gpio_direction_output (EQOS_RST_PAD ,1 ); -mdelay (100 ); -} -static int setup_eqos (void ) {struct iomuxc_gpr_base_regs *gpr = (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR ; -setup_iomux_eqos (); -/* set INTF as RGMII, enable RGMII TXC clock */ clrsetbits_le32 (&gpr->gpr[1 ],IOMUXC_GPR_GPR1_GPR_ENET_QOS_INTF_SEL_MASK ,BIT (16 ));
Signature · 1 line
2.7.4
PATCH 8/9 imx8mp_evk: Delete noncached memory config
In reply to Ye LiDWC EQOS driver has removed to use noncached memory, so delete the configuration from iMX8MP EVK head file.
--- include/configs/imx8mp_evk.h | 3 --- 1 file changed, 3 deletions(-)
include/configs/imx8mp_evk.h +0 -3
@@ -50,9 +50,6 @@#define FEC_QUIRK_ENET_MAC #define DWC_NET_PHYADDR 1 -#ifdef CONFIG_DWC_ETH_QOS -#define CONFIG_SYS_NONCACHED_MEMORY (1 * SZ_1M)/* 1M */ -#endif #define PHY_ANEG_TIMEOUT 20000
Signature · 1 line
2.7.4
PATCH 9/9 imx8mp_evk: Enable the DWC EQoS iMX driver
In reply to Ye LiEnable the EQoS i.MX driver in defconfig, also enable the PHYLIB to facilitate the case that only has FEC enabled.
--- configs/imx8mp_evk_defconfig | 2 ++ 1 file changed, 2 insertions(+)
configs/imx8mp_evk_defconfig +2 -0
@@ -80,9 +80,11 @@ CONFIG_MMC_HS400_ES_SUPPORT=y CONFIG_MMC_HS400_SUPPORT=y CONFIG_FSL_ESDHC_IMX=y CONFIG_PHY_REALTEK=y +CONFIG_PHYLIB=y CONFIG_DM_ETH=y CONFIG_PHY_GIGE=y CONFIG_DWC_ETH_QOS=y +CONFIG_DWC_ETH_QOS_IMX=y CONFIG_FEC_MXC=y CONFIG_MII=y CONFIG_PINCTRL=y
Signature · 1 line
2.7.4
Hi Ye,
series was completely lost on my side, I tried to check it today but it is obsolete now and conflicts with Peng's series for MX8ULP. So I drop it, yorry, you should rebase and post it again.
Best regards,
Stefano Babic
Quoted 101 lines · Ye Li
Parse the "phy-reset-gpios", "phy-reset-post-delay" and "phy-reset-duration" properties from eqos node to control the ethernet PHY reset at driver probe.
Reset PHY once is enough that can reduce the time cost to get IP after the first time.Signed-off-by Ye Li <[email protected]>--- drivers/net/dwc_eth_qos.c | 55 +++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 55 insertions(+)drivers/net/dwc_eth_qos.c +55
-0@@ -303,6 +303,8 @@ struct eqos_priv {struct eqos_tegra186_regs *tegra186_regs;struct reset_ctl reset_ctl;struct gpio_desc phy_reset_gpio; +uint32_t reset_delay; +uint32_t reset_post_delay;struct clk clk_master_bus;struct clk clk_rx;struct clk clk_ptp_ref;@@ -1880,6 +1882,7 @@ static int eqos_probe_resources_imx(struct udevice *dev) {struct eqos_priv *eqos =dev_get_priv (dev);phy_interface_t interface; +int ret =0 ;debug ("%s(dev=%p):\n" , __func__, dev);@@ -1890,8 +1893,52 @@ static int eqos_probe_resources_imx(struct udevice *dev)return -EINVAL ; } + ret =gpio_request_by_name (dev,"phy-reset-gpios" ,0 , + &eqos->phy_reset_gpio, +GPIOD_IS_OUT |GPIOD_IS_OUT_ACTIVE ); +if (ret) { +pr_debug ("gpio_request_by_name(phy reset) failed: %d" , ret); + } + +if (dm_gpio_is_valid (&eqos->phy_reset_gpio)) { + eqos->reset_delay =dev_read_u32_default (dev,"phy-reset-duration" ,1 ); +if (eqos->reset_delay >1000 ) { +pr_err ("phy reset duration should be <= 1000ms\n" ); +/* property value wrong, use default value */ + eqos->reset_delay =1 ; + } + +mdelay (eqos->reset_delay); + + eqos->reset_post_delay =dev_read_u32_default (dev, +"phy-reset-post-delay" , +0 ); +if (eqos->reset_post_delay >1000 ) { +pr_err ("phy reset post delay should be <= 1000ms\n" ); +/* property value wrong, use default value */ + eqos->reset_post_delay =0 ; + } + + ret =dm_gpio_set_value (&eqos->phy_reset_gpio,0 ); +if (ret <0 ) { +pr_err ("dm_gpio_set_value(phy_reset, deassert) failed: %d" , ret); + goto err_free_gpio_phy_reset; + } + +if (eqos->reset_post_delay) +mdelay (eqos->reset_post_delay); + } +debug ("%s: OK\n" , __func__);return 0 ; + +err_free_gpio_phy_reset: +if (dm_gpio_is_valid (&eqos->phy_reset_gpio)) { +dm_gpio_free (dev, &eqos->phy_reset_gpio); + } + +debug ("%s: returns %d\n" , __func__, ret); +return ret; }static phy_interface_t eqos_get_interface_imx (struct udevice *dev)@@ -1951,6 +1998,14 @@ static int eqos_remove_resources_stm32(struct udevice *dev)static int eqos_remove_resources_imx (struct udevice *dev) { +struct eqos_priv *eqos =dev_get_priv (dev); + +debug ("%s(dev=%p):\n" , __func__, dev); +if (dm_gpio_is_valid (&eqos->phy_reset_gpio)) { +dm_gpio_free (dev, &eqos->phy_reset_gpio); + } + +debug ("%s: OK\n" , __func__);return 0 ; }
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
Hi Stefano,
Ok. I will rebase the patches after the 8ULP is merged.
Best regards,
Ye Li
Quoted 143 lines
-----Original Message-----
From: Stefano Babic <[email protected]>
Sent: Saturday, July 17, 2021 8:54 PM
To: Ye Li <[email protected]>; [email protected]; [email protected]; Peng Fan <[email protected]>; [email protected]
Cc: [email protected]; dl-uboot-imx <[email protected]>; [email protected]
Subject: [EXT] Re: [PATCH 1/9] net: eqos: Add PHY reset control for i.MX platformCaution: EXT Email
Hi Ye,
series was completely lost on my side, I tried to check it today but it is obsolete now and conflicts with Peng's series for MX8ULP. So I drop it, yorry, you should rebase and post it again.
Best regards,
Stefano BabicQuoted 9 lines · Ye Li
Parse the "phy-reset-gpios", "phy-reset-post-delay" and "phy-reset-duration" properties from eqos node to control the ethernet PHY reset at driver probe.
Reset PHY once is enough that can reduce the time cost to get IP after the first time.Signed-off-by Ye Li <[email protected]>--- drivers/net/dwc_eth_qos.c | 55+++++++++++++++++++++++++++++++++++++++++++++++
drivers/net/dwc_eth_qos.c static int eqos_probe_resources_imx(struct
Quoted 16 lines
1 file changed, 55 insertions(+)drivers/net/dwc_eth_qos.c +2
-0@@ -303,6 +303,8 @@ struct eqos_priv {struct eqos_tegra186_regs *tegra186_regs;struct reset_ctl reset_ctl;struct gpio_desc phy_reset_gpio; +uint32_t reset_delay; +uint32_t reset_post_delay;struct clk clk_master_bus;struct clk clk_rx;struct clk clk_ptp_ref;@@ -1880,6 +1882,7 @@ static int eqos_probe_resources_imx(structudevice *dev)
drivers/net/dwc_eth_qos.c static int eqos_probe_resources_imx(struct
Quoted 8 lines
drivers/net/dwc_eth_qos.c +1
-0{struct eqos_priv *eqos =dev_get_priv (dev);phy_interface_t interface; +int ret =0 ;debug ("%s(dev=%p):\n" , __func__, dev);@@ -1890,8 +1893,52 @@ static int eqos_probe_resources_imx(structudevice *dev)
drivers/net/dwc_eth_qos.c static int eqos_probe_resources_imx(struct udevice *dev)
Quoted 6 lines
drivers/net/dwc_eth_qos.c +3
-0return -EINVAL ; } + ret = gpio_request_by_name(dev, "phy-reset-gpios", 0, + &eqos->phy_reset_gpio, + GPIOD_IS_OUT |
GPIOD_IS_OUT_ACTIVE);drivers/net/dwc_eth_qos.c static int eqos_probe_resources_imx(struct · line 1900
Quoted 2 lines
drivers/net/dwc_eth_qos.c +2
-0+if (ret) { + pr_debug("gpio_request_by_name(phy reset) failed: %d",ret);
drivers/net/dwc_eth_qos.c static int eqos_probe_resources_imx(struct udevice *dev)
Quoted 4 lines
drivers/net/dwc_eth_qos.c +4
-0+ } + +if (dm_gpio_is_valid (&eqos->phy_reset_gpio)) { + eqos->reset_delay = dev_read_u32_default(dev,"phy-reset-duration", 1);
drivers/net/dwc_eth_qos.c static int eqos_probe_resources_imx(struct · line 1906
Quoted 2 lines
drivers/net/dwc_eth_qos.c +2
-0+if (eqos->reset_delay >1000 ) { + pr_err("phy reset duration should be <=1000ms\n");
drivers/net/dwc_eth_qos.c static int eqos_probe_resources_imx(struct udevice *dev) · line 1921
Quoted 8 lines
drivers/net/dwc_eth_qos.c +8
-0+/* property value wrong, use default value */ + eqos->reset_delay =1 ; + } + +mdelay (eqos->reset_delay); + + eqos->reset_post_delay = dev_read_u32_default(dev, +"phy-reset-post-delay",
drivers/net/dwc_eth_qos.c static int eqos_probe_resources_imx(struct udevice *dev)
Quoted 3 lines
drivers/net/dwc_eth_qos.c +3
-0+ 0); +if (eqos->reset_post_delay >1000 ) { + pr_err("phy reset post delay should be <=1000ms\n");
drivers/net/dwc_eth_qos.c static int eqos_probe_resources_imx(struct udevice *dev)
Quoted 7 lines
drivers/net/dwc_eth_qos.c +7
-0+/* property value wrong, use default value */ + eqos->reset_post_delay =0 ; + } + + ret =dm_gpio_set_value (&eqos->phy_reset_gpio,0 ); +if (ret <0 ) { + pr_err("dm_gpio_set_value(phy_reset, deassert)failed: %d", ret);
Quoted 27 lines
drivers/net/dwc_eth_qos.c +15
-0+ goto err_free_gpio_phy_reset; + } + +if (eqos->reset_post_delay) +mdelay (eqos->reset_post_delay); + } +debug ("%s: OK\n" , __func__);return 0 ; + +err_free_gpio_phy_reset: +if (dm_gpio_is_valid (&eqos->phy_reset_gpio)) { +dm_gpio_free (dev, &eqos->phy_reset_gpio); + } + +debug ("%s: returns %d\n" , __func__, ret); +return ret; }static phy_interface_t eqos_get_interface_imx (struct udevice *dev)@@ -1951,6 +1998,14 @@ static int eqos_remove_resources_stm32(struct udevice *dev)static int eqos_remove_resources_imx (struct udevice *dev) {drivers/net/dwc_eth_qos.c static int eqos_remove_resources_stm32(struct · line 2011
Quoted 10 lines
drivers/net/dwc_eth_qos.c +8
-0+struct eqos_priv *eqos =dev_get_priv (dev); + +debug ("%s(dev=%p):\n" , __func__, dev); +if (dm_gpio_is_valid (&eqos->phy_reset_gpio)) { +dm_gpio_free (dev, &eqos->phy_reset_gpio); + } + +debug ("%s: OK\n" , __func__);return 0 ; }--
================================================================
=====
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
================================================================
=====