Skip to contentSkip to conversation

Fix loading of module radeonfb on PowerMac

PATCH In review Mathieu Malaterre 2 participants 3 messages Nov 23, 2016 – Feb 2, 2017

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 Fix loading of module radeonfb on PowerMac

When the linux kernel is build with (typical kernel ship with Debian installer):

CONFIG_FB_OF=y
CONFIG_VT_HW_CONSOLE_BINDING=y
CONFIG_FB_RADEON=m

The offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:

[   96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007)
[   96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref]
[   96.551531] radeonfb (0000:00:10.0): cannot request region 0.
[   96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16

This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.

The problem is that offb call pci_request_region first, and then radeonfb tries to do it, and since one is trying to take over from the other, it can't do that because the area is already reserved.

It should be noticed that offb_destroy is never called which explain the need to skip error detection on the radeonfb side.

---

v2: Remove compilation warning

v3: Hide error messages on PPC

 drivers/video/fbdev/aty/radeon_base.c | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)
drivers/video/fbdev/aty/radeon_base.c +27 -0
index 218339a..837c86a 100644
@@ -2259,6 +2259,22 @@ static struct bin_attribute edid2_attr = {
 	.read	= radeon_show_edid2,
 };
 
+static int radeon_kick_out_firmware_fb(struct pci_dev *pdev)
+{
+	struct apertures_struct *ap;
+
+	ap = alloc_apertures(1);
+	if (!ap)
+		return -ENOMEM;
+
+	ap->ranges[0].base = pci_resource_start(pdev, 0);
+	ap->ranges[0].size = pci_resource_len(pdev, 0);
+
+	remove_conflicting_framebuffers(ap, KBUILD_MODNAME, false);
+	kfree(ap);
+
+	return 0;
+}
 
 static int radeonfb_pci_register(struct pci_dev *pdev,
 				 const struct pci_device_id *ent)
@@ -2314,20 +2330,29 @@ static int radeonfb_pci_register(struct pci_dev *pdev,
 	rinfo->fb_base_phys = pci_resource_start (pdev, 0);
 	rinfo->mmio_base_phys = pci_resource_start (pdev, 2);
 
+	ret = radeon_kick_out_firmware_fb(pdev);
+	if (ret)
+		return ret;
+
 	/* request the mem regions */
 	ret = pci_request_region(pdev, 0, "radeonfb framebuffer");
+  /* this is not an error on PowerMac where offb already requested mem regions */
+#ifndef CONFIG_PPC
 	if (ret < 0) {
 		printk( KERN_ERR "radeonfb (%s): cannot request region 0.\n",
 			pci_name(rinfo->pdev));
 		goto err_release_fb;
 	}
+#endif
 
 	ret = pci_request_region(pdev, 2, "radeonfb mmio");
+#ifndef CONFIG_PPC
 	if (ret < 0) {
 		printk( KERN_ERR "radeonfb (%s): cannot request region 2.\n",
 			pci_name(rinfo->pdev));
 		goto err_release_pci0;
 	}
+#endif
 
 	/* map the regions */
 	rinfo->mmio_base = ioremap(rinfo->mmio_base_phys, RADEON_REGSIZE);
@@ -2511,10 +2536,12 @@ static int radeonfb_pci_register(struct pci_dev *pdev,
 	iounmap(rinfo->mmio_base);
 err_release_pci2:
 	pci_release_region(pdev, 2);
+#ifndef CONFIG_PPC
 err_release_pci0:
 	pci_release_region(pdev, 0);
 err_release_fb:
         framebuffer_release(info);
+#endif
 err_disable:
 err_out:
 	return ret;
Signature · 1 line
2.1.4
#1 lore raw

Any chance this patch could be considered for inclusion this time ?

Thanks

Quoted 111 lines · Mathieu Malaterre

When the linux kernel is build with (typical kernel ship with Debian installer):

CONFIG_FB_OF=y
CONFIG_VT_HW_CONSOLE_BINDING=y
CONFIG_FB_RADEON=m

The offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:

[   96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007)
[   96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref]
[   96.551531] radeonfb (0000:00:10.0): cannot request region 0.
[   96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16

This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.

The problem is that offb call pci_request_region first, and then radeonfb tries to do it, and since one is trying to take over from the other, it can't do that because the area is already reserved.

It should be noticed that offb_destroy is never called which explain the need to skip error detection on the radeonfb side.

---

v2: Remove compilation warning

v3: Hide error messages on PPC

 drivers/video/fbdev/aty/radeon_base.c | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)
drivers/video/fbdev/aty/radeon_base.c +27 -1
index 218339a..837c86a 100644
@@ -2259,6 +2259,22 @@ static struct bin_attribute edid2_attr = {
        .read   = radeon_show_edid2,
 };
 
+static int radeon_kick_out_firmware_fb(struct pci_dev *pdev)
+{
+       struct apertures_struct *ap;
+
+       ap = alloc_apertures(1);
+       if (!ap)
+               return -ENOMEM;
+
+       ap->ranges[0].base = pci_resource_start(pdev, 0);
+       ap->ranges[0].size = pci_resource_len(pdev, 0);
+
+       remove_conflicting_framebuffers(ap, KBUILD_MODNAME, false);
+       kfree(ap);
+
+       return 0;
+}
 
 static int radeonfb_pci_register(struct pci_dev *pdev,
                                 const struct pci_device_id *ent)
@@ -2314,20 +2330,29 @@ static int radeonfb_pci_register(struct pci_dev *pdev,
        rinfo->fb_base_phys = pci_resource_start (pdev, 0);
        rinfo->mmio_base_phys = pci_resource_start (pdev, 2);
 
+       ret = radeon_kick_out_firmware_fb(pdev);
+       if (ret)
+               return ret;
+
        /* request the mem regions */
        ret = pci_request_region(pdev, 0, "radeonfb framebuffer");
+  /* this is not an error on PowerMac where offb already requested mem regions */
+#ifndef CONFIG_PPC
        if (ret < 0) {
                printk( KERN_ERR "radeonfb (%s): cannot request region 0.\n",
                        pci_name(rinfo->pdev));
                goto err_release_fb;
        }
+#endif
 
        ret = pci_request_region(pdev, 2, "radeonfb mmio");
+#ifndef CONFIG_PPC
        if (ret < 0) {
                printk( KERN_ERR "radeonfb (%s): cannot request region 2.\n",
                        pci_name(rinfo->pdev));
                goto err_release_pci0;
        }
+#endif
 
        /* map the regions */
        rinfo->mmio_base = ioremap(rinfo->mmio_base_phys, RADEON_REGSIZE);
@@ -2511,10 +2536,12 @@ static int radeonfb_pci_register(struct pci_dev *pdev,
        iounmap(rinfo->mmio_base);
 err_release_pci2:
        pci_release_region(pdev, 2);
+#ifndef CONFIG_PPC
 err_release_pci0:
        pci_release_region(pdev, 0);
 err_release_fb:
         framebuffer_release(info);
+#endif
 err_disable:
 err_out:
        return ret;
--

2.1.4

#2 lore raw

Hi,

Quoted 74 lines · Mathieu Malaterre

Any chance this patch could be considered for inclusion this time ?

Thanks

Quoted 69 lines · Mathieu Malaterre

When the linux kernel is build with (typical kernel ship with Debian installer):

CONFIG_FB_OF=y
CONFIG_VT_HW_CONSOLE_BINDING=y
CONFIG_FB_RADEON=m

The offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:

[   96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007)
[   96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref]
[   96.551531] radeonfb (0000:00:10.0): cannot request region 0.
[   96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16

This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.

The problem is that offb call pci_request_region first, and then radeonfb tries to do it, and since one is trying to take over from the other, it can't do that because the area is already reserved.

It should be noticed that offb_destroy is never called which explain the need to skip error detection on the radeonfb side.

---

v2: Remove compilation warning

v3: Hide error messages on PPC

 drivers/video/fbdev/aty/radeon_base.c | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)
drivers/video/fbdev/aty/radeon_base.c +16 -0
index 218339a..837c86a 100644
@@ -2259,6 +2259,22 @@ static struct bin_attribute edid2_attr = {
        .read   = radeon_show_edid2,
 };
 
+static int radeon_kick_out_firmware_fb(struct pci_dev *pdev)
+{
+       struct apertures_struct *ap;
+
+       ap = alloc_apertures(1);
+       if (!ap)
+               return -ENOMEM;
+
+       ap->ranges[0].base = pci_resource_start(pdev, 0);
+       ap->ranges[0].size = pci_resource_len(pdev, 0);
+
+       remove_conflicting_framebuffers(ap, KBUILD_MODNAME, false);
+       kfree(ap);
+
+       return 0;
+}
 
 static int radeonfb_pci_register(struct pci_dev *pdev,
                                 const struct pci_device_id *ent)
@@ -2314,20 +2330,29 @@ static int radeonfb_pci_register(struct pci_dev *pdev,
        rinfo->fb_base_phys = pci_resource_start (pdev, 0);
        rinfo->mmio_base_phys = pci_resource_start (pdev, 2);
 
Quoted 8 lines

drivers/video/fbdev/aty/radeon_base.c static int radeonfb_pci_register(struct pci_dev *pdev, · line 2340

Quoted 8 lines
drivers/video/fbdev/aty/radeon_base.c +6 -0
+       ret = radeon_kick_out_firmware_fb(pdev);
+       if (ret)
+               return ret;
+
        /* request the mem regions */
        ret = pci_request_region(pdev, 0, "radeonfb framebuffer");
+  /* this is not an error on PowerMac where offb already requested mem regions */
+#ifndef CONFIG_PPC

This doesn't look correct:

- PPC is not only PowerMac and offb supports more cards than radeon (while radeonfb can be used for secondary graphics card)

- offb can be disabled

(i.e. in CONFIG_FB_OF=n && CONFIG_FB_RADEON=y case error checking will be missing now)

The last put_fb_info() on fb_info should call ->fb_destroy (offb_destroy in our case) and remove_conflicting_framebuffers() is calling put_fb_info() so there is some extra reference on fb_info somewhere preventing it from going away.

Please look into fixing this.

Quoted 25 lines
Quoted 25 lines
drivers/video/fbdev/aty/radeon_base.c +4 -0
        if (ret < 0) {
                printk( KERN_ERR "radeonfb (%s): cannot request region 0.\n",
                        pci_name(rinfo->pdev));
                goto err_release_fb;
        }
+#endif
 
        ret = pci_request_region(pdev, 2, "radeonfb mmio");
+#ifndef CONFIG_PPC
        if (ret < 0) {
                printk( KERN_ERR "radeonfb (%s): cannot request region 2.\n",
                        pci_name(rinfo->pdev));
                goto err_release_pci0;
        }
+#endif
 
        /* map the regions */
        rinfo->mmio_base = ioremap(rinfo->mmio_base_phys, RADEON_REGSIZE);
@@ -2511,10 +2536,12 @@ static int radeonfb_pci_register(struct pci_dev *pdev,
        iounmap(rinfo->mmio_base);
 err_release_pci2:
        pci_release_region(pdev, 2);
+#ifndef CONFIG_PPC
 err_release_pci0:
        pci_release_region(pdev, 0);
Quoted 8 lines
Quoted 8 lines
drivers/video/fbdev/aty/radeon_base.c +1 -1
 err_release_fb:
         framebuffer_release(info);
+#endif
 err_disable:
 err_out:
        return ret;
--

2.1.4

Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics