Enable Bluetooth functinality for WCN6750
Subsystems (5)
v2 cover Enable Bluetooth functinality for WCN6750
These patches enables Bluetooth functinalties for new Qualcomm Bluetooth SoC wcn6750.
Changes in v2:
* Converted Qualcomm bluetooth bindings to DT schema.
* Added device tree bindings for QTI chip wcn6750 in converted DT schema.
Venkata Lakshmi Narayana Gubba (3):
Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750
dt-bindings: net: bluetooth: Convert to DT schema
dt-bindings: net: bluetooth: Add device tree bindings for QTI chip
wcn6750
.../devicetree/bindings/net/qualcomm-bluetooth.txt | 69 ---------- .../bindings/net/qualcomm-bluetooth.yaml | 139 +++++++++++++++++++++ drivers/bluetooth/btqca.c | 88 +++++++++---- drivers/bluetooth/btqca.h | 15 ++- drivers/bluetooth/hci_qca.c | 106 ++++++++++++---- 5 files changed, 300 insertions(+), 117 deletions(-) delete mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt create mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
PATCH v2 1/3 Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750
Added regulators,GPIOs and changes required to power on/off wcn6750. Added support for firmware download for wcn6750.
Changes done in detail:
1. Added regulators and corresponding current values.
2. Added sw_ctrl GPIO pin which is output from BT SoC and indicates status of clock supply to BT SoC.
3. Added inline function to check if the SoC type is wcn399x or wcn6750.
4. Modified the function qca_wcn3990_init() to support wcn6750 and renamed it to qca_regulator_init().
5. Added BT_ON and BT_OFF macros.
6. Added support to download mbn type firmware image as wcn6750 supports mbn type image.
7. If mbn type image is not present then we will check for tlv type image.
8. Moved extracting rom version info to common place as this code is common in all if else ladder in qca_uart_setup.
--- drivers/bluetooth/btqca.c | 88 ++++++++++++++++++++++++++---------- drivers/bluetooth/btqca.h | 15 ++++++- drivers/bluetooth/hci_qca.c | 106 ++++++++++++++++++++++++++++++++++---------- 3 files changed, 161 insertions(+), 48 deletions(-)
drivers/bluetooth/btqca.c +64 -24
@@ -182,7 +182,8 @@ int qca_send_pre_shutdown_cmd(struct hci_dev *hdev) }EXPORT_SYMBOL_GPL (qca_send_pre_shutdown_cmd); -static void qca_tlv_check_data (struct qca_fw_config *config, +static void qca_tlv_check_data (struct hci_dev *hdev, +struct qca_fw_config *config,const struct firmware *fw,enum qca_btsoc_type soc_type) {const u8 *data;
@@ -194,19 +195,21 @@ static void qca_tlv_check_data(struct qca_fw_config *config,struct tlv_type_nvm *tlv_nvm;uint8_t nvm_baud_rate = config->user_baud_rate; - tlv = (struct tlv_type_hdr *)fw->data; - - type_len =le32_to_cpu (tlv->type_len); - length = (type_len >>8 ) &0x00ffffff ; - -BT_DBG ("TLV Type\t\t : 0x%x" , type_len &0x000000ff ); -BT_DBG ("Length\t\t : %d bytes" , length); - config->dnld_mode =QCA_SKIP_EVT_NONE ; config->dnld_type =QCA_SKIP_EVT_NONE ;switch (config->type) { +case ELF_TYPE_PATCH : + config->dnld_mode =QCA_SKIP_EVT_VSE_CC ; + config->dnld_type =QCA_SKIP_EVT_VSE_CC ; + +bt_dev_dbg (hdev,"File Class : 0x%x" , fw->data[4 ]); +bt_dev_dbg (hdev,"Data Encoding : 0x%x" , fw->data[5 ]); +bt_dev_dbg (hdev,"File version : 0x%x" , fw->data[6 ]); +break ;case TLV_TYPE_PATCH : + tlv = (struct tlv_type_hdr *)fw->data; + type_len =le32_to_cpu (tlv->type_len); tlv_patch = (struct tlv_type_patch *)tlv->data;/* For Rome version 1.1 to 3.1, all segment commands
@@ -218,6 +221,7 @@ static void qca_tlv_check_data(struct qca_fw_config *config, config->dnld_mode = tlv_patch->download_mode; config->dnld_type = config->dnld_mode; +BT_DBG ("TLV Type\t\t : 0x%x" , type_len &0x000000ff );BT_DBG ("Total Length : %d bytes" ,le32_to_cpu (tlv_patch->total_size)); BT_DBG("Patch Data Length : %d bytes",
@@ -243,6 +247,14 @@ static void qca_tlv_check_data(struct qca_fw_config *config,break ;case TLV_TYPE_NVM : + tlv = (struct tlv_type_hdr *)fw->data; + + type_len =le32_to_cpu (tlv->type_len); + length = (type_len >>8 ) &0x00ffffff ; + +BT_DBG ("TLV Type\t\t : 0x%x" , type_len &0x000000ff ); +BT_DBG ("Length\t\t : %d bytes" , length); + idx =0 ; data = tlv->data;while (idx < length) {
@@ -387,7 +399,8 @@ static int qca_inject_cmd_complete_event(struct hci_dev *hdev)static int qca_download_firmware (struct hci_dev *hdev,struct qca_fw_config *config, -enum qca_btsoc_type soc_type) +enum qca_btsoc_type soc_type, +u8 rom_ver) {const struct firmware *fw;const u8 *segment;
@@ -397,12 +410,29 @@ static int qca_download_firmware(struct hci_dev *hdev, ret =request_firmware (&fw, config->fwname, &hdev->dev);if (ret) { -bt_dev_err (hdev,"QCA Failed to request file: %s (%d)" , - config->fwname, ret); -return ret; +/* For WCN6750, if mbn file is not present then check for +* tlv file. +*/ +if (soc_type ==QCA_WCN6750 && config->type ==ELF_TYPE_PATCH ) { +bt_dev_dbg (hdev,"QCA Failed to request file: %s (%d)" , + config->fwname, ret); + config->type =TLV_TYPE_PATCH ; +snprintf (config->fwname,sizeof (config->fwname), +"qca/msbtfw%02x.tlv" , rom_ver); + ret =request_firmware (&fw, config->fwname, &hdev->dev); +if (ret) { +bt_dev_err (hdev,"QCA Failed to request file: %s (%d)" , + config->fwname, ret); +return ret; + } + }else { +bt_dev_err (hdev,"QCA Failed to request file: %s (%d)" , + config->fwname, ret); +return ret; + } } -qca_tlv_check_data (config, fw, soc_type); +qca_tlv_check_data (hdev, config, fw, soc_type); segment = fw->data; remain = fw->size;
@@ -502,27 +532,33 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate, config.user_baud_rate = baudrate; +/* Firmware files to download are based on ROM version. +* ROM version is derived from last two bytes of soc_ver. +*/ + rom_ver = ((soc_ver &0x00000f00 ) >>0x04 ) | + (soc_ver &0x0000000f ); +/* Download rampatch file */ config.type =TLV_TYPE_PATCH ;if (qca_is_wcn399x (soc_type)) { -/* Firmware files to download are based on ROM version. -* ROM version is derived from last two bytes of soc_ver. -*/ - rom_ver = ((soc_ver &0x00000f00 ) >>0x04 ) | - (soc_ver &0x0000000f );snprintf (config.fwname,sizeof (config.fwname),"qca/crbtfw%02x.tlv" , rom_ver); }else if (soc_type ==QCA_QCA6390 ) { - rom_ver = ((soc_ver &0x00000f00 ) >>0x04 ) | - (soc_ver &0x0000000f );snprintf (config.fwname,sizeof (config.fwname),"qca/htbtfw%02x.tlv" , rom_ver); + }else if (soc_type ==QCA_WCN6750 ) { +/* Choose mbn file by default.If mbn file is not found +* then choose tlv file +*/ + config.type =ELF_TYPE_PATCH ; +snprintf (config.fwname,sizeof (config.fwname), +"qca/msbtfw%02x.mbn" , rom_ver); }else {snprintf (config.fwname,sizeof (config.fwname),"qca/rampatch_%08x.bin" , soc_ver); } - err =qca_download_firmware (hdev, &config, soc_type); + err =qca_download_firmware (hdev, &config, soc_type, rom_ver);if (err <0 ) {bt_dev_err (hdev,"QCA Failed to download patch (%d)" , err);return err;
@@ -548,11 +584,14 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,else if (soc_type ==QCA_QCA6390 )snprintf (config.fwname,sizeof (config.fwname),"qca/htnv%02x.bin" , rom_ver); +else if (soc_type ==QCA_WCN6750 ) +snprintf (config.fwname,sizeof (config.fwname), +"qca/msnv%02x.bin" , rom_ver);else snprintf (config.fwname,sizeof (config.fwname),"qca/nvm_%08x.bin" , soc_ver); - err =qca_download_firmware (hdev, &config, soc_type); + err =qca_download_firmware (hdev, &config, soc_type, rom_ver);if (err <0 ) {bt_dev_err (hdev,"QCA Failed to download NVM (%d)" , err);return err;
@@ -564,13 +603,14 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,return err; } -/* WCN399x supports the Microsoft vendor extension with 0xFD70 as the +/* WCN399x and WCN6750 supports the Microsoft vendor extension with 0xFD70 as the * VsMsftOpCode. */ switch (soc_type) {case QCA_WCN3990 :case QCA_WCN3991 :case QCA_WCN3998 : +case QCA_WCN6750 :hci_set_msft_opcode (hdev,0xFD70 );break ;default :
drivers/bluetooth/btqca.h +14 -1
@@ -80,7 +80,8 @@ enum qca_tlv_dnld_mode {enum qca_tlv_type {TLV_TYPE_PATCH =1 , -TLV_TYPE_NVM +TLV_TYPE_NVM , +ELF_TYPE_PATCH };struct qca_fw_config {
@@ -143,6 +144,7 @@ enum qca_btsoc_type {QCA_WCN3998 ,QCA_WCN3991 ,QCA_QCA6390 , + QCA_WCN6750 };#if IS_ENABLED (CONFIG_BT_QCA )
@@ -160,6 +162,12 @@ static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)return soc_type ==QCA_WCN3990 || soc_type ==QCA_WCN3991 || soc_type == QCA_WCN3998; } +static inline bool qca_is_wcn399x_wcn6750 (enum qca_btsoc_type soc_type) +{ +return soc_type ==QCA_WCN3990 || soc_type ==QCA_WCN3991 || + soc_type ==QCA_WCN3998 || soc_type ==QCA_WCN6750 ; +} +#else static inline int qca_set_bdaddr_rome (struct hci_dev *hdev,const bdaddr_t *bdaddr)
@@ -192,6 +200,11 @@ static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)return false; } +static inline bool qca_is_wcn399x_wcn6750 (enum qca_btsoc_type soc_type) +{ +return false; +} +static inline int qca_send_pre_shutdown_cmd (struct hci_dev *hdev) {return -EOPNOTSUPP ;
drivers/bluetooth/hci_qca.c +83 -23
235 lines not on this page · raw message
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
This is automated email and please do not reply to this email!
Dear submitter,
Thank you for submitting the patches to the linux bluetooth mailing list. This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=470381
---Test result---
##############################
Test: CheckPatch - FAIL
dt-bindings: net: bluetooth: Convert to DT schema
WARNING: added, moved or deleted file(s), does MAINTAINERS need updating? #11:
deleted file mode 100644
WARNING: DT binding docs and includes should be a separate patch. See: Documentation/devicetree/bindings/submitting-patches.rst
WARNING: DT binding docs and includes should be a separate patch. See: Documentation/devicetree/bindings/submitting-patches.rst
ERROR: trailing whitespace
#114: FILE: Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml:24:
+ - qcom,qca6390-bt $
ERROR: trailing whitespace
#119: FILE: Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml:29:
+ $
ERROR: trailing whitespace
#136: FILE: Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml:46:
+ max-speed: $
ERROR: trailing whitespace
#175: FILE: Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml:85:
+ firmware-name = "crnv21.bin";^I^I$
total: 4 errors, 3 warnings, 87 lines checked
NOTE: For some of the reported defects, checkpatch may be able to
mechanically convert to the typical style using --fix or --fix-inplace.
NOTE: Whitespace errors detected.
You may wish to use scripts/cleanpatch or scripts/cleanfile
"[PATCH] dt-bindings: net: bluetooth: Convert to DT schema" has style problems, please review.
NOTE: If any of the errors are false positives, please report
them to the maintainer, see CHECKPATCH in MAINTAINERS.
##############################
Test: CheckGitLint - FAIL
dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750
1: T1 Title exceeds max length (74>72): "dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750"
##############################
Test: CheckBuildK - PASS
##############################
Test: CheckTestRunner: Setup - PASS
##############################
Test: CheckTestRunner: l2cap-tester - PASS
Total: 40, Passed: 34 (85.0%), Failed: 0, Not Run: 6
##############################
Test: CheckTestRunner: bnep-tester - PASS
Total: 1, Passed: 1 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: mgmt-tester - PASS
Total: 416, Passed: 402 (96.6%), Failed: 0, Not Run: 14
##############################
Test: CheckTestRunner: rfcomm-tester - PASS
Total: 9, Passed: 9 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: sco-tester - PASS
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: smp-tester - PASS
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: userchan-tester - PASS
Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0
---
Regards,
Linux Bluetooth
c[?7l[2JSeaBIOS (version 1.13.0-1ubuntu1.1) Booting from ROM..c[?7l[2Jearly console in extract_kernelinput_data: 0x0000000001e6f2e0input_len: 0x000000000035722f
output: 0x0000000001000000output_len: 0x00000000011945fckernel_total_size: 0x0000000001030000needed_size: 0x0000000001200000trampoline_32bit: 0x000000000009d000
Physical KASLR using RDTSC...
Virtual KASLR using RDTSC...
Decompressing Linux... Parsing ELF... Performing relocations... done.
Booting the kernel.
Linux version 5.12.0-rc4-g83f5627c41ca (root@e38846f99b91) (gcc (Ubuntu 9.3.0-17ubuntu1~20.04) 9.3.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #2 Tue Apr 20 17:46:02 UTC 2021
Command line: console=ttyS0,115200n8 earlyprintk=serial rootfstype=9p rootflags=trans=virtio,version=9p2000.L acpi=off pci=noacpi noapic quiet ro init=/github/workspace/bluez/tools/test-runner TESTHOME=/github/workspace TESTDBUS=0 TESTMONITOR=0 TESTDEVS=0 TESTAUTO=0 TESTARGS='/github/workspace/bluez/tools/l2cap-tester' x86/fpu: x87 FPU will use FXSAVE
BIOS-provided physical RAM map:
BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
BIOS-e820: [mem 0x0000000000100000-0x000000000bffdfff] usable
BIOS-e820: [mem 0x000000000bffe000-0x000000000bffffff] reserved
BIOS-e820: [mem 0x00000000b0000000-0x00000000bfffffff] reserved
BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved
printk: bootconsole [earlyser0] enabled
Memory KASLR using RDTSC...
Poking KASLR using RDTSC...
Mounting sysfs to /sys
Mounting proc to /proc
Mounting devtmpfs to /dev
Creating /dev/pts
Mounting devpts to /dev/pts
Creating /dev/shm
Mounting tmpfs to /dev/shm
Mounting tmpfs to /run
Mounting tmpfs to /tmp
Mounting debugfs to /sys/kernel/debug
Linking /dev/fd to /proc/self/fd
Linking /dev/stdin to /proc/self/fd/0
Linking /dev/stdout to /proc/self/fd/1
Linking /dev/stderr to /proc/self/fd/2
Creating new session group leader
Setting controlling terminal
Creating /var/lib/bluetooth
Failed to create filesystem: No such file or directory
Creating /etc/bluetooth
Failed to create filesystem: No such file or directory
Creating /etc/dbus-1
Failed to create filesystem: No such file or directory
Creating /usr/share/dbus-1
Running command /github/workspace/bluez/tools/l2cap-tester
New process 39 created
Changing into directory /github/workspace
Basic L2CAP Socket - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Basic L2CAP Socket - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
Basic L2CAP Socket - Success - setup complete
Basic L2CAP Socket - Success - run
Basic L2CAP Socket - Success - test passed
Basic L2CAP Socket - Success - teardown
Index Removed callback
Index: 0x0000
Basic L2CAP Socket - Success - teardown complete
Basic L2CAP Socket - Success - done
Non-connected getpeername - Failure - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Non-connected getpeername - Failure - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
Non-connected getpeername - Failure - setup complete Non-connected getpeername - Failure - run Non-connected getpeername - Failure - test passed Non-connected getpeername - Failure - teardown
Index Removed callback
Index: 0x0000
Non-connected getpeername - Failure - teardown complete Non-connected getpeername - Failure - done
L2CAP BR/EDR Client - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP BR/EDR Client - Success - setup complete
L2CAP BR/EDR Client - Success - run
Connect in progress
Successfully connected
L2CAP BR/EDR Client - Success - test passed
L2CAP BR/EDR Client - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client - Success - teardown complete
L2CAP BR/EDR Client - Success - done
L2CAP BR/EDR Client SSP - Success 1 - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client SSP - Success 1 - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
Client enable SSP status 0x00
L2CAP BR/EDR Client SSP - Success 1 - setup complete L2CAP BR/EDR Client SSP - Success 1 - run
Connect in progress
Successfully connected
L2CAP BR/EDR Client SSP - Success 1 - test passed L2CAP BR/EDR Client SSP - Success 1 - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client SSP - Success 1 - teardown complete L2CAP BR/EDR Client SSP - Success 1 - done
L2CAP BR/EDR Client SSP - Success 2 - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client SSP - Success 2 - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
Client enable SSP status 0x00
L2CAP BR/EDR Client SSP - Success 2 - setup complete L2CAP BR/EDR Client SSP - Success 2 - run
Connect in progress
Successfully connected
L2CAP BR/EDR Client SSP - Success 2 - test passed L2CAP BR/EDR Client SSP - Success 2 - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client SSP - Success 2 - teardown complete L2CAP BR/EDR Client SSP - Success 2 - done
L2CAP BR/EDR Client PIN Code - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client PIN Code - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP BR/EDR Client PIN Code - Success - setup complete L2CAP BR/EDR Client PIN Code - Success - run
Connect in progress
Successfully connected
L2CAP BR/EDR Client PIN Code - Success - test passed L2CAP BR/EDR Client PIN Code - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client PIN Code - Success - teardown complete L2CAP BR/EDR Client PIN Code - Success - done
L2CAP BR/EDR Client - Read Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client - Read Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP BR/EDR Client - Read Success - setup complete L2CAP BR/EDR Client - Read Success - run
Connect in progress
Successfully connected
L2CAP BR/EDR Client - Read Success - test passed L2CAP BR/EDR Client - Read Success - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client - Read Success - teardown complete L2CAP BR/EDR Client - Read Success - done
L2CAP BR/EDR Client - Write Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client - Write Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP BR/EDR Client - Write Success - setup complete L2CAP BR/EDR Client - Write Success - run
Connect in progress
Successfully connected
L2CAP BR/EDR Client - Write Success - test passed L2CAP BR/EDR Client - Write Success - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client - Write Success - teardown complete L2CAP BR/EDR Client - Write Success - done
L2CAP BR/EDR Client - Invalid PSM 1 - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client - Invalid PSM 1 - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP BR/EDR Client - Invalid PSM 1 - setup complete L2CAP BR/EDR Client - Invalid PSM 1 - run
Connect in progress
Connect failed: Connection refused (111)
L2CAP BR/EDR Client - Invalid PSM 1 - test passed L2CAP BR/EDR Client - Invalid PSM 1 - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client - Invalid PSM 1 - teardown complete L2CAP BR/EDR Client - Invalid PSM 1 - done
L2CAP BR/EDR Client - Invalid PSM 2 - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client - Invalid PSM 2 - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP BR/EDR Client - Invalid PSM 2 - setup complete L2CAP BR/EDR Client - Invalid PSM 2 - run
Connect in progress
Connect failed: Connection refused (111)
L2CAP BR/EDR Client - Invalid PSM 2 - test passed L2CAP BR/EDR Client - Invalid PSM 2 - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client - Invalid PSM 2 - teardown complete L2CAP BR/EDR Client - Invalid PSM 2 - done
L2CAP BR/EDR Client - Invalid PSM 3 - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client - Invalid PSM 3 - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
Client enable SSP status 0x00
L2CAP BR/EDR Client - Invalid PSM 3 - setup complete L2CAP BR/EDR Client - Invalid PSM 3 - run
Connect in progress
Connect failed: Connection refused (111)
L2CAP BR/EDR Client - Invalid PSM 3 - test passed L2CAP BR/EDR Client - Invalid PSM 3 - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client - Invalid PSM 3 - teardown complete L2CAP BR/EDR Client - Invalid PSM 3 - done
L2CAP BR/EDR Client - Socket Shut WR Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client - Socket Shut WR Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP BR/EDR Client - Socket Shut WR Success - setup complete L2CAP BR/EDR Client - Socket Shut WR Success - run
Connect in progress
Successfully connected
L2CAP BR/EDR Client - Socket Shut WR Success - test passed L2CAP BR/EDR Client - Socket Shut WR Success - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client - Socket Shut WR Success - teardown complete L2CAP BR/EDR Client - Socket Shut WR Success - done
L2CAP BR/EDR Server - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Server - Success - setup
Powering on controller
Controller powered on
L2CAP BR/EDR Server - Success - setup complete
L2CAP BR/EDR Server - Success - run
Listening for connections
New client connection with handle 0x002a
Sending L2CAP Request from client
Client received response code 0x03
L2CAP BR/EDR Server - Success - test passed
Successfully connected
L2CAP BR/EDR Server - Success - test passed
L2CAP BR/EDR Server - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Server - Success - teardown complete
L2CAP BR/EDR Server - Success - done
L2CAP BR/EDR Server - Read Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Server - Read Success - setup
Powering on controller
Controller powered on
L2CAP BR/EDR Server - Read Success - setup complete L2CAP BR/EDR Server - Read Success - run
Listening for connections
New client connection with handle 0x002a Sending L2CAP Request from client
Client received response code 0x03
L2CAP BR/EDR Server - Read Success - test passed L2CAP BR/EDR Server - Read Success - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Server - Read Success - teardown complete L2CAP BR/EDR Server - Read Success - done
L2CAP BR/EDR Server - Write Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Server - Write Success - setup
Powering on controller
Controller powered on
L2CAP BR/EDR Server - Write Success - setup complete L2CAP BR/EDR Server - Write Success - run
Listening for connections
New client connection with handle 0x002a Sending L2CAP Request from client
Client received response code 0x03
L2CAP BR/EDR Server - Write Success - test passed L2CAP BR/EDR Server - Write Success - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Server - Write Success - teardown complete L2CAP BR/EDR Server - Write Success - done
L2CAP BR/EDR Server - Security Block - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Server - Security Block - setup
Powering on controller
Controller powered on
Server enable SSP status 0x00
L2CAP BR/EDR Server - Security Block - setup complete L2CAP BR/EDR Server - Security Block - run
Listening for connections
New client connection with handle 0x002a Sending L2CAP Request from client
Client received response code 0x03
L2CAP BR/EDR Server - Security Block - test passed L2CAP BR/EDR Server - Security Block - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Server - Security Block - teardown complete L2CAP BR/EDR Server - Security Block - done
L2CAP BR/EDR Server - Invalid PSM - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Server - Invalid PSM - setup
Powering on controller
Controller powered on
L2CAP BR/EDR Server - Invalid PSM - setup complete L2CAP BR/EDR Server - Invalid PSM - run
New client connection with handle 0x002a Sending L2CAP Request from client
Client received response code 0x03
L2CAP BR/EDR Server - Invalid PSM - test passed L2CAP BR/EDR Server - Invalid PSM - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Server - Invalid PSM - teardown complete L2CAP BR/EDR Server - Invalid PSM - done
L2CAP BR/EDR Server - Invalid PDU - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Server - Invalid PDU - setup
Powering on controller
Controller powered on
L2CAP BR/EDR Server - Invalid PDU - setup complete L2CAP BR/EDR Server - Invalid PDU - run
New client connection with handle 0x002a Sending L2CAP Request from client
Bluetooth: Wrong link type (-71)
Client received response code 0x01
L2CAP BR/EDR Server - Invalid PDU - test passed L2CAP BR/EDR Server - Invalid PDU - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Server - Invalid PDU - teardown complete L2CAP BR/EDR Server - Invalid PDU - done
L2CAP BR/EDR Server - Invalid Disconnect CID - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Server - Invalid Disconnect CID - setup
Powering on controller
Controller powered on
L2CAP BR/EDR Server - Invalid Disconnect CID - setup complete L2CAP BR/EDR Server - Invalid Disconnect CID - run
New client connection with handle 0x002a
Sending L2CAP Request from client
Client received response code 0x01
L2CAP BR/EDR Server - Invalid Disconnect CID - test passed L2CAP BR/EDR Server - Invalid Disconnect CID - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Server - Invalid Disconnect CID - teardown complete L2CAP BR/EDR Server - Invalid Disconnect CID - done
L2CAP BR/EDR Server - Invalid Config CID - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Server - Invalid Config CID - setup
Powering on controller
Controller powered on
L2CAP BR/EDR Server - Invalid Config CID - setup complete L2CAP BR/EDR Server - Invalid Config CID - run
New client connection with handle 0x002a Sending L2CAP Request from client
Client received response code 0x01
L2CAP BR/EDR Server - Invalid Config CID - test passed L2CAP BR/EDR Server - Invalid Config CID - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Server - Invalid Config CID - teardown complete L2CAP BR/EDR Server - Invalid Config CID - done
L2CAP LE Client - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP LE Client - Success - setup complete
L2CAP LE Client - Success - run
Connect in progress
Successfully connected
L2CAP LE Client - Success - test passed
L2CAP LE Client - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client - Success - teardown complete
L2CAP LE Client - Success - done
L2CAP LE Client, Direct Advertising - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client, Direct Advertising - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP LE Client, Direct Advertising - Success - setup complete L2CAP LE Client, Direct Advertising - Success - run
Connect in progress
Received advertising parameters HCI command
L2CAP LE Client, Direct Advertising - Success - test passed L2CAP LE Client, Direct Advertising - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client, Direct Advertising - Success - teardown complete L2CAP LE Client, Direct Advertising - Success - done
L2CAP LE Client SMP - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client SMP - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP LE Client SMP - Success - setup complete
L2CAP LE Client SMP - Success - run
Connect in progress
Successfully connected
L2CAP LE Client SMP - Success - test passed
Bluetooth: hci0: link tx timeout
L2CAP LE Client SMP - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client SMP - Success - teardown complete
L2CAP LE Client SMP - Success - done
L2CAP LE Client - Command Reject - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client - Command Reject - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP LE Client - Command Reject - setup complete
L2CAP LE Client - Command Reject - run
Connect in progress
New connection with handle 0x002a
Connect failed: Connection refused (111)
L2CAP LE Client - Command Reject - test passed
L2CAP LE Client - Command Reject - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client - Command Reject - teardown complete L2CAP LE Client - Command Reject - done
L2CAP LE Client - Connection Reject - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP LE Client - Connection Reject - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP LE Client - Connection Reject - setup complete L2CAP LE Client - Connection Reject - run
Can't connect socket: No route to host (113)
L2CAP LE Client - Connection Reject - test passed L2CAP LE Client - Connection Reject - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client - Connection Reject - teardown complete L2CAP LE Client - Connection Reject - done
L2CAP LE Client - Close socket 1 - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client - Close socket 1 - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP LE Client - Close socket 1 - setup complete
L2CAP LE Client - Close socket 1 - run
Connect in progress, sk = 13
Will close socket during scan phase...
Checking whether scan was properly stopped...
L2CAP LE Client - Close socket 1 - test passed
L2CAP LE Client - Close socket 1 - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client - Close socket 1 - teardown complete L2CAP LE Client - Close socket 1 - done
L2CAP LE Client - Close socket 2 - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client - Close socket 2 - setup
Powering on controller
Controller powered on
L2CAP LE Client - Close socket 2 - setup complete
L2CAP LE Client - Close socket 2 - run
Connect in progress, sk = 13
Client set connectable status 0x00
Client set connectable status 0x00
L2CAP LE Client - Close socket 2 - test passed
L2CAP LE Client - Close socket 2 - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client - Close socket 2 - teardown complete L2CAP LE Client - Close socket 2 - done
L2CAP LE Client - Open two sockets - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client - Open two sockets - setup
Powering on controller
Controller powered on
L2CAP LE Client - Open two sockets - setup complete L2CAP LE Client - Open two sockets - run
Connect in progress, sk = 13
HCI Command 0x200b length 7
HCI Command 0x200c length 2
Connect in progress, sk = 14
HCI Command 0x200c length 2
Client set connectable status 0x00
HCI Command 0x200d length 25
HCI Command 0x2016 length 2
Successfully connected
Successfully connected
L2CAP LE Client - Open two sockets - test passed
(l2cap-tester:39): GLib-WARNING **: 17:46:11.096: Invalid file descriptor. L2CAP LE Client - Open two sockets - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client - Open two sockets - teardown complete L2CAP LE Client - Open two sockets - done
L2CAP LE Client - Open two sockets close one - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client - Open two sockets close one - setup
Powering on controller
Controller powered on
L2CAP LE Client - Open two sockets close one - setup complete L2CAP LE Client - Open two sockets close one - run
Connect in progress, sk = 13
HCI Command 0x200b length 7
HCI Command 0x200c length 2
Connect in progress, sk = 14
Closing first socket! 13
HCI Command 0x200c length 2
Client set connectable status 0x00
HCI Command 0x200d length 25
HCI Command 0x2016 length 2
Successfully connected
L2CAP LE Client - Open two sockets close one - test passed
(l2cap-tester:39): GLib-WARNING **: 17:46:11.136: Invalid file descriptor. L2CAP LE Client - Open two sockets close one - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client - Open two sockets close one - teardown complete L2CAP LE Client - Open two sockets close one - done
L2CAP LE Client - Invalid PSM - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client - Invalid PSM - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP LE Client - Invalid PSM - setup complete
L2CAP LE Client - Invalid PSM - run
Connect in progress
Connect failed: Connection refused (111)
L2CAP LE Client - Invalid PSM - test passed
L2CAP LE Client - Invalid PSM - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client - Invalid PSM - teardown complete
L2CAP LE Client - Invalid PSM - done
L2CAP LE Server - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Server - Success - setup
Powering on controller
Controller powered on
L2CAP LE Server - Success - setup complete
L2CAP LE Server - Success - run
Listening for connections
New client connection with handle 0x002a
Sending L2CAP Request from client
Successfully connected
L2CAP LE Server - Success - test passed
Client received response code 0x15
L2CAP LE Server - Success - test passed
L2CAP LE Server - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Server - Success - teardown complete
L2CAP LE Server - Success - done
L2CAP LE Server - Nval SCID - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Server - Nval SCID - setup
Powering on controller
Controller powered on
L2CAP LE Server - Nval SCID - setup complete
L2CAP LE Server - Nval SCID - run
Listening for connections
New client connection with handle 0x002a
Sending L2CAP Request from client
Client received response code 0x15
L2CAP LE Server - Nval SCID - test passed
L2CAP LE Server - Nval SCID - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Server - Nval SCID - teardown complete
L2CAP LE Server - Nval SCID - done
L2CAP Ext-Flowctl Client - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP Ext-Flowctl Client - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP Ext-Flowctl Client - Success - setup complete L2CAP Ext-Flowctl Client - Success - run
Can't set mode: Protocol not available (92)
L2CAP Ext-Flowctl Client - Success - test not run L2CAP Ext-Flowctl Client - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP Ext-Flowctl Client - Success - teardown complete L2CAP Ext-Flowctl Client - Success - done
L2CAP Ext-Flowctl Client, Direct Advertising - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP Ext-Flowctl Client, Direct Advertising - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP Ext-Flowctl Client, Direct Advertising - Success - setup complete L2CAP Ext-Flowctl Client, Direct Advertising - Success - run
Can't set mode: Protocol not available (92)
L2CAP Ext-Flowctl Client, Direct Advertising - Success - test not run L2CAP Ext-Flowctl Client, Direct Advertising - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP Ext-Flowctl Client, Direct Advertising - Success - teardown complete L2CAP Ext-Flowctl Client, Direct Advertising - Success - done
L2CAP Ext-Flowctl Client SMP - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP Ext-Flowctl Client SMP - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP Ext-Flowctl Client SMP - Success - setup complete L2CAP Ext-Flowctl Client SMP - Success - run
Can't set mode: Protocol not available (92)
L2CAP Ext-Flowctl Client SMP - Success - test not run L2CAP Ext-Flowctl Client SMP - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP Ext-Flowctl Client SMP - Success - teardown complete L2CAP Ext-Flowctl Client SMP - Success - done
L2CAP Ext-Flowctl Client - Command Reject - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP Ext-Flowctl Client - Command Reject - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP Ext-Flowctl Client - Command Reject - setup complete L2CAP Ext-Flowctl Client - Command Reject - run
Can't set mode: Protocol not available (92)
L2CAP Ext-Flowctl Client - Command Reject - test not run L2CAP Ext-Flowctl Client - Command Reject - teardown
Index Removed callback
Index: 0x0000
L2CAP Ext-Flowctl Client - Command Reject - teardown complete L2CAP Ext-Flowctl Client - Command Reject - done
L2CAP Ext-Flowctl Client - Open two sockets - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP Ext-Flowctl Client - Open two sockets - setup
Powering on controller
Controller powered on
L2CAP Ext-Flowctl Client - Open two sockets - setup complete L2CAP Ext-Flowctl Client - Open two sockets - run
Can't set mode: Protocol not available (92) Error in create_l2cap_sock
L2CAP Ext-Flowctl Client - Open two sockets - test not run L2CAP Ext-Flowctl Client - Open two sockets - teardown
Index Removed callback
Index: 0x0000
L2CAP Ext-Flowctl Client - Open two sockets - teardown complete L2CAP Ext-Flowctl Client - Open two sockets - done
L2CAP Ext-Flowctl Client - Open two sockets close one - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP Ext-Flowctl Client - Open two sockets close one - setup
Powering on controller
Controller powered on
L2CAP Ext-Flowctl Client - Open two sockets close one - setup complete L2CAP Ext-Flowctl Client - Open two sockets close one - run
Can't set mode: Protocol not available (92)
Error in create_l2cap_sock
L2CAP Ext-Flowctl Client - Open two sockets close one - test not run L2CAP Ext-Flowctl Client - Open two sockets close one - teardown
Index Removed callback
Index: 0x0000
L2CAP Ext-Flowctl Client - Open two sockets close one - teardown complete L2CAP Ext-Flowctl Client - Open two sockets close one - done
L2CAP LE ATT Client - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE ATT Client - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP LE ATT Client - Success - setup complete
L2CAP LE ATT Client - Success - run
Connect in progress
Successfully connected
L2CAP LE ATT Client - Success - test passed
L2CAP LE ATT Client - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP LE ATT Client - Success - teardown complete
L2CAP LE ATT Client - Success - done
L2CAP LE ATT Server - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE ATT Server - Success - setup
Powering on controller
Controller powered on
L2CAP LE ATT Server - Success - setup complete
L2CAP LE ATT Server - Success - run
Listening for connections
New client connection with handle 0x002a
Successfully connected
L2CAP LE ATT Server - Success - test passed
L2CAP LE ATT Server - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP LE ATT Server - Success - teardown complete
L2CAP LE ATT Server - Success - done
Test Summary
------------
Basic L2CAP Socket - Success Passed 0.065 seconds Non-connected getpeername - Failure Passed 0.014 seconds L2CAP BR/EDR Client - Success Passed 0.033 seconds L2CAP BR/EDR Client SSP - Success 1 Passed 0.031 seconds L2CAP BR/EDR Client SSP - Success 2 Passed 0.026 seconds L2CAP BR/EDR Client PIN Code - Success Passed 0.021 seconds L2CAP BR/EDR Client - Read Success Passed 0.018 seconds L2CAP BR/EDR Client - Write Success Passed 0.020 seconds L2CAP BR/EDR Client - Invalid PSM 1 Passed 0.021 seconds L2CAP BR/EDR Client - Invalid PSM 2 Passed 0.015 seconds L2CAP BR/EDR Client - Invalid PSM 3 Passed 0.018 seconds L2CAP BR/EDR Client - Socket Shut WR Success Passed 0.020 seconds L2CAP BR/EDR Server - Success Passed 0.023 seconds L2CAP BR/EDR Server - Read Success Passed 0.022 seconds L2CAP BR/EDR Server - Write Success Passed 0.024 seconds L2CAP BR/EDR Server - Security Block Passed 0.020 seconds L2CAP BR/EDR Server - Invalid PSM Passed 0.023 seconds L2CAP BR/EDR Server - Invalid PDU Passed 0.025 seconds L2CAP BR/EDR Server - Invalid Disconnect CID Passed 0.021 seconds L2CAP BR/EDR Server - Invalid Config CID Passed 0.015 seconds L2CAP LE Client - Success Passed 0.023 seconds L2CAP LE Client, Direct Advertising - Success Passed 0.020 seconds L2CAP LE Client SMP - Success Passed 0.041 seconds L2CAP LE Client - Command Reject Passed 0.019 seconds L2CAP LE Client - Connection Reject Passed 0.020 seconds L2CAP LE Client - Close socket 1 Passed 0.017 seconds L2CAP LE Client - Close socket 2 Passed 0.019 seconds L2CAP LE Client - Open two sockets Passed 0.060 seconds L2CAP LE Client - Open two sockets close one Passed 0.024 seconds L2CAP LE Client - Invalid PSM Passed 0.016 seconds L2CAP LE Server - Success Passed 0.025 seconds L2CAP LE Server - Nval SCID Passed 0.019 seconds L2CAP Ext-Flowctl Client - Success Not Run L2CAP Ext-Flowctl Client, Direct Advertising - Success Not Run L2CAP Ext-Flowctl Client SMP - Success Not Run L2CAP Ext-Flowctl Client - Command Reject Not Run L2CAP Ext-Flowctl Client - Open two sockets Not Run L2CAP Ext-Flowctl Client - Open two sockets close one Not Run L2CAP LE ATT Client - Success Passed 0.014 seconds L2CAP LE ATT Server - Success Passed 0.014 seconds
Total: 40, Passed: 34 (85.0%), Failed: 0, Not Run: 6 Overall execution time: 0.928 seconds Process 39 exited with status 0
reboot: Restarting system
c[?7l[2JSeaBIOS (version 1.13.0-1ubuntu1.1) Booting from ROM..c[?7l[2Jearly console in extract_kernelinput_data: 0x0000000001e6f2e0input_len: 0x000000000035722f
output: 0x0000000001000000output_len: 0x00000000011945fckernel_total_size: 0x0000000001030000needed_size: 0x0000000001200000trampoline_32bit: 0x000000000009d000
Physical KASLR using RDTSC...
Virtual KASLR using RDTSC...
Decompressing Linux... Parsing ELF... Performing relocations... done.
Booting the kernel.
Linux version 5.12.0-rc4-g83f5627c41ca (root@e38846f99b91) (gcc (Ubuntu 9.3.0-17ubuntu1~20.04) 9.3.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #2 Tue Apr 20 17:46:02 UTC 2021
Command line: console=ttyS0,115200n8 earlyprintk=serial rootfstype=9p rootflags=trans=virtio,version=9p2000.L acpi=off pci=noacpi noapic quiet ro init=/github/workspace/bluez/tools/test-runner TESTHOME=/github/workspace TESTDBUS=0 TESTMONITOR=0 TESTDEVS=0 TESTAUTO=0 TESTARGS='/github/workspace/bluez/tools/bnep-tester' x86/fpu: x87 FPU will use FXSAVE
BIOS-provided physical RAM map:
BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
BIOS-e820: [mem 0x0000000000100000-0x000000000bffdfff] usable
BIOS-e820: [mem 0x000000000bffe000-0x000000000bffffff] reserved
BIOS-e820: [mem 0x00000000b0000000-0x00000000bfffffff] reserved
BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved
printk: bootconsole [earlyser0] enabled
Memory KASLR using RDTSC...
Poking KASLR using RDTSC...
Mounting sysfs to /sys
Mounting proc to /proc
Mounting devtmpfs to /dev
Creating /dev/pts
Mounting devpts to /dev/pts
Creating /dev/shm
Mounting tmpfs to /dev/shm
Mounting tmpfs to /run
Mounting tmpfs to /tmp
Mounting debugfs to /sys/kernel/debug
Linking /dev/fd to /proc/self/fd
Linking /dev/stdin to /proc/self/fd/0
Linking /dev/stdout to /proc/self/fd/1
Linking /dev/stderr to /proc/self/fd/2
Creating new session group leader
Setting controlling terminal
Creating /var/lib/bluetooth
Failed to create filesystem: No such file or directory
Creating /etc/bluetooth
Failed to create filesystem: No such file or directory
Creating /etc/dbus-1
Failed to create filesystem: No such file or directory
Creating /usr/share/dbus-1
Running command /github/workspace/bluez/tools/bnep-tester
New process 39 created
Changing into directory /github/workspace
Basic BNEP Socket - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Basic BNEP Socket - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
Basic BNEP Socket - Success - setup complete
Basic BNEP Socket - Success - run
Basic BNEP Socket - Success - test passed
Basic BNEP Socket - Success - teardown
Index Removed callback
Index: 0x0000
Basic BNEP Socket - Success - teardown complete
Basic BNEP Socket - Success - done
Test Summary
------------
Basic BNEP Socket - Success Passed 0.060 seconds
Total: 1, Passed: 1 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.072 seconds Process 39 exited with status 0
reboot: Restarting system
c[?7l[2JSeaBIOS (version 1.13.0-1ubuntu1.1) Booting from ROM..c[?7l[2Jearly console in extract_kernelinput_data: 0x0000000001e6f2e0input_len: 0x000000000035722f
output: 0x0000000001000000output_len: 0x00000000011945fckernel_total_size: 0x0000000001030000needed_size: 0x0000000001200000trampoline_32bit: 0x000000000009d000
Physical KASLR using RDTSC...
Virtual KASLR using RDTSC...
Decompressing Linux... Parsing ELF... Performing relocations... done.
Booting the kernel.
Linux version 5.12.0-rc4-g83f5627c41ca (root@e38846f99b91) (gcc (Ubuntu 9.3.0-17ubuntu1~20.04) 9.3.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #2 Tue Apr 20 17:46:02 UTC 2021
Command line: console=ttyS0,115200n8 earlyprintk=serial rootfstype=9p rootflags=trans=virtio,version=9p2000.L acpi=off pci=noacpi noapic quiet ro init=/github/workspace/bluez/tools/test-runner TESTHOME=/github/workspace TESTDBUS=0 TESTMONITOR=0 TESTDEVS=0 TESTAUTO=0 TESTARGS='/github/workspace/bluez/tools/mgmt-tester' x86/fpu: x87 FPU will use FXSAVE
BIOS-provided physical RAM map:
BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
BIOS-e820: [mem 0x0000000000100000-0x000000000bffdfff] usable
BIOS-e820: [mem 0x000000000bffe000-0x000000000bffffff] reserved
BIOS-e820: [mem 0x00000000b0000000-0x00000000bfffffff] reserved
BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved
printk: bootconsole [earlyser0] enabled
Memory KASLR using RDTSC...
Poking KASLR using RDTSC...
Mounting sysfs to /sys
Mounting proc to /proc
Mounting devtmpfs to /dev
Creating /dev/pts
Mounting devpts to /dev/pts
Creating /dev/shm
Mounting tmpfs to /dev/shm
Mounting tmpfs to /run
Mounting tmpfs to /tmp
Mounting debugfs to /sys/kernel/debug
Linking /dev/fd to /proc/self/fd
Linking /dev/stdin to /proc/self/fd/0
Linking /dev/stdout to /proc/self/fd/1
Linking /dev/stderr to /proc/self/fd/2
Creating new session group leader
Setting controlling terminal
Creating /var/lib/bluetooth
Failed to create filesystem: No such file or directory
Creating /etc/bluetooth
Failed to create filesystem: No such file or directory
Creating /etc/dbus-1
Failed to create filesystem: No such file or directory
Creating /usr/share/dbus-1
Running command /github/workspace/bluez/tools/mgmt-tester
New process 39 created
Changing into directory /github/workspace
Controller setup - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Controller setup - setup
Controller setup - setup complete
Controller setup - run
Controller setup - test passed
Controller setup - teardown
Index Removed callback
Index: 0x0000
Controller setup - teardown complete
Controller setup - done
Controller setup (BR/EDR-only) - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Controller setup (BR/EDR-only) - setup
Controller setup (BR/EDR-only) - setup complete
Controller setup (BR/EDR-only) - run
Controller setup (BR/EDR-only) - test passed
Controller setup (BR/EDR-only) - teardown
Index Removed callback
Index: 0x0000
Controller setup (BR/EDR-only) - teardown complete Controller setup (BR/EDR-only) - done
Controller setup (LE) - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Controller setup (LE) - setup
Controller setup (LE) - setup complete
Controller setup (LE) - run
Controller setup (LE) - test passed
Controller setup (LE) - teardown
Index Removed callback
Index: 0x0000
Controller setup (LE) - teardown complete
Controller setup (LE) - done
Invalid command - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Invalid command - setup
Invalid command - setup complete
Invalid command - run
Sending <unknown opcode> (0xffff)
Test condition added, total 1
<unknown opcode> (0xffff): Unknown Command (0x01) Test condition complete, 0 left
Invalid command - test passed
Invalid command - teardown
Index Removed callback
Index: 0x0000
Invalid command - teardown complete
Invalid command - done
Read version - Success - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read version - Success - setup
Read version - Success - setup complete
Read version - Success - run
Sending Read Version (0x0001)
Test condition added, total 1
Read Version (0x0001): Success (0x00)
Test condition complete, 0 left
Read version - Success - test passed
Read version - Success - teardown
Index Removed callback
Index: 0x0000
Read version - Success - teardown complete
Read version - Success - done
Read version - Invalid parameters - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read version - Invalid parameters - setup Read version - Invalid parameters - setup complete Read version - Invalid parameters - run
Sending Read Version (0x0001)
Test condition added, total 1
Read Version (0x0001): Invalid Parameters (0x0d) Test condition complete, 0 left
Read version - Invalid parameters - test passed Read version - Invalid parameters - teardown
Index Removed callback
Index: 0x0000
Read version - Invalid parameters - teardown complete Read version - Invalid parameters - done
Read version - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read version - Invalid index - setup
Read version - Invalid index - setup complete
Read version - Invalid index - run
Sending Read Version (0x0001)
Test condition added, total 1
Read Version (0x0001): Invalid Index (0x11)
Test condition complete, 0 left
Read version - Invalid index - test passed
Read version - Invalid index - teardown
Index Removed callback
Index: 0x0000
Read version - Invalid index - teardown complete
Read version - Invalid index - done
Read commands - Invalid parameters - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read commands - Invalid parameters - setup Read commands - Invalid parameters - setup complete Read commands - Invalid parameters - run
Sending Read Commands (0x0002)
Test condition added, total 1
Read Commands (0x0002): Invalid Parameters (0x0d) Test condition complete, 0 left
Read commands - Invalid parameters - test passed Read commands - Invalid parameters - teardown
Index Removed callback
Index: 0x0000
Read commands - Invalid parameters - teardown complete Read commands - Invalid parameters - done
Read commands - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read commands - Invalid index - setup
Read commands - Invalid index - setup complete
Read commands - Invalid index - run
Sending Read Commands (0x0002)
Test condition added, total 1
Read Commands (0x0002): Invalid Index (0x11)
Test condition complete, 0 left
Read commands - Invalid index - test passed
Read commands - Invalid index - teardown
Index Removed callback
Index: 0x0000
Read commands - Invalid index - teardown complete
Read commands - Invalid index - done
Read index list - Invalid parameters - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read index list - Invalid parameters - setup Read index list - Invalid parameters - setup complete Read index list - Invalid parameters - run
Sending Read Index List (0x0003)
Test condition added, total 1
Read Index List (0x0003): Invalid Parameters (0x0d) Test condition complete, 0 left
Read index list - Invalid parameters - test passed Read index list - Invalid parameters - teardown
Index Removed callback
Index: 0x0000
Read index list - Invalid parameters - teardown complete Read index list - Invalid parameters - done
Read index list - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read index list - Invalid index - setup
Read index list - Invalid index - setup complete
Read index list - Invalid index - run
Sending Read Index List (0x0003)
Test condition added, total 1
Read Index List (0x0003): Invalid Index (0x11)
Test condition complete, 0 left
Read index list - Invalid index - test passed
Read index list - Invalid index - teardown
Index Removed callback
Index: 0x0000
Read index list - Invalid index - teardown complete Read index list - Invalid index - done
Read info - Invalid parameters - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read info - Invalid parameters - setup
Read info - Invalid parameters - setup complete Read info - Invalid parameters - run
Sending Read Controller Info (0x0004)
Test condition added, total 1
Read Controller Info (0x0004): Invalid Parameters (0x0d) Test condition complete, 0 left
Read info - Invalid parameters - test passed
Read info - Invalid parameters - teardown
Index Removed callback
Index: 0x0000
Read info - Invalid parameters - teardown complete Read info - Invalid parameters - done
Read info - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read info - Invalid index - setup
Read info - Invalid index - setup complete Read info - Invalid index - run
Sending Read Controller Info (0x0004)
Test condition added, total 1
Read Controller Info (0x0004): Invalid Index (0x11) Test condition complete, 0 left
Read info - Invalid index - test passed
Read info - Invalid index - teardown
Index Removed callback
Index: 0x0000
Read info - Invalid index - teardown complete
Read info - Invalid index - done
Read unconfigured index list - Invalid parameters - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read unconfigured index list - Invalid parameters - setup Read unconfigured index list - Invalid parameters - setup complete Read unconfigured index list - Invalid parameters - run
Sending Read Unconfigured Index List (0x0036)
Test condition added, total 1
Read Unconfigured Index List (0x0036): Invalid Parameters (0x0d) Test condition complete, 0 left
Read unconfigured index list - Invalid parameters - test passed Read unconfigured index list - Invalid parameters - teardown
Index Removed callback
Index: 0x0000
Read unconfigured index list - Invalid parameters - teardown complete Read unconfigured index list - Invalid parameters - done
Read unconfigured index list - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read unconfigured index list - Invalid index - setup Read unconfigured index list - Invalid index - setup complete Read unconfigured index list - Invalid index - run
Sending Read Unconfigured Index List (0x0036) Test condition added, total 1
Read Unconfigured Index List (0x0036): Invalid Index (0x11) Test condition complete, 0 left
Read unconfigured index list - Invalid index - test passed Read unconfigured index list - Invalid index - teardown
Index Removed callback
Index: 0x0000
Read unconfigured index list - Invalid index - teardown complete Read unconfigured index list - Invalid index - done
Read configuration info - Invalid parameters - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read configuration info - Invalid parameters - setup
Read configuration info - Invalid parameters - setup complete
Read configuration info - Invalid parameters - run
Sending Read Controller Configuration Information (0x0037)
Test condition added, total 1
Read Controller Configuration Information (0x0037): Invalid Parameters (0x0d) Test condition complete, 0 left
Read configuration info - Invalid parameters - test passed
Read configuration info - Invalid parameters - teardown
Index Removed callback
Index: 0x0000
Read configuration info - Invalid parameters - teardown complete Read configuration info - Invalid parameters - done
Read configuration info - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read configuration info - Invalid index - setup
Read configuration info - Invalid index - setup complete
Read configuration info - Invalid index - run
Sending Read Controller Configuration Information (0x0037) Test condition added, total 1
Read Controller Configuration Information (0x0037): Invalid Index (0x11) Test condition complete, 0 left
Read configuration info - Invalid index - test passed
Read configuration info - Invalid index - teardown
Index Removed callback
Index: 0x0000
Read configuration info - Invalid index - teardown complete Read configuration info - Invalid index - done
Read extended index list - Invalid parameters - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read extended index list - Invalid parameters - setup
Read extended index list - Invalid parameters - setup complete Read extended index list - Invalid parameters - run
Sending Read Extended Controller Index List (0x003c)
Test condition added, total 1
Read Extended Controller Index List (0x003c): Invalid Parameters (0x0d) Test condition complete, 0 left
Read extended index list - Invalid parameters - test passed Read extended index list - Invalid parameters - teardown
Index Removed callback
Index: 0x0000
Read extended index list - Invalid parameters - teardown complete Read extended index list - Invalid parameters - done
Read extended index list - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read extended index list - Invalid index - setup
Read extended index list - Invalid index - setup complete Read extended index list - Invalid index - run
Sending Read Extended Controller Index List (0x003c) Test condition added, total 1
Read Extended Controller Index List (0x003c): Invalid Index (0x11) Test condition complete, 0 left
Read extended index list - Invalid index - test passed Read extended index list - Invalid index - teardown
Index Removed callback
Index: 0x0000
Read extended index list - Invalid index - teardown complete Read extended index list - Invalid index - done
Set powered on - Success - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered on - Success - setup
Set powered on - Success - setup complete
Set powered on - Success - run
Registering new settings notification
Test condition added, total 1
Sending Set Powered (0x0005)
Test condition added, total 2
Set Powered (0x0005): Success (0x00)
Test condition complete, 1 left
New settings 0x00000081 received
Unregistering new settings notification
Test condition complete, 0 left
Set powered on - Success - test passed
Set powered on - Success - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set powered on - Success - teardown complete
Set powered on - Success - done
Set powered on - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered on - Invalid parameters 1 - setup Set powered on - Invalid parameters 1 - setup complete Set powered on - Invalid parameters 1 - run
Sending Set Powered (0x0005)
Test condition added, total 1
Set Powered (0x0005): Invalid Parameters (0x0d) Test condition complete, 0 left
Set powered on - Invalid parameters 1 - test passed Set powered on - Invalid parameters 1 - teardown
Index Removed callback
Index: 0x0000
Set powered on - Invalid parameters 1 - teardown complete Set powered on - Invalid parameters 1 - done
Set powered on - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered on - Invalid parameters 2 - setup Set powered on - Invalid parameters 2 - setup complete Set powered on - Invalid parameters 2 - run
Sending Set Powered (0x0005)
Test condition added, total 1
Set Powered (0x0005): Invalid Parameters (0x0d) Test condition complete, 0 left
Set powered on - Invalid parameters 2 - test passed Set powered on - Invalid parameters 2 - teardown
Index Removed callback
Index: 0x0000
Set powered on - Invalid parameters 2 - teardown complete Set powered on - Invalid parameters 2 - done
Set powered on - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered on - Invalid parameters 3 - setup Set powered on - Invalid parameters 3 - setup complete Set powered on - Invalid parameters 3 - run
Sending Set Powered (0x0005)
Test condition added, total 1
Set Powered (0x0005): Invalid Parameters (0x0d) Test condition complete, 0 left
Set powered on - Invalid parameters 3 - test passed Set powered on - Invalid parameters 3 - teardown
Index Removed callback
Index: 0x0000
Set powered on - Invalid parameters 3 - teardown complete Set powered on - Invalid parameters 3 - done
Set powered on - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered on - Invalid index - setup
Set powered on - Invalid index - setup complete
Set powered on - Invalid index - run
Sending Set Powered (0x0005)
Test condition added, total 1
Set Powered (0x0005): Invalid Index (0x11)
Test condition complete, 0 left
Set powered on - Invalid index - test passed
Set powered on - Invalid index - teardown
Index Removed callback
Index: 0x0000
Set powered on - Invalid index - teardown complete Set powered on - Invalid index - done
Set powered on - Privacy and Advertising - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set powered on - Privacy and Advertising - setup
Initial settings completed
Client set connectable: Success (0x00)
Set powered on - Privacy and Advertising - setup complete Set powered on - Privacy and Advertising - run
Sending Set Advertising (0x0029)
Test condition added, total 1
Set Advertising (0x0029): Success (0x00)
Test condition complete, 0 left
Set powered on - Privacy and Advertising - test passed Set powered on - Privacy and Advertising - teardown
Index Removed callback
Index: 0x0000
Set powered on - Privacy and Advertising - teardown complete Set powered on - Privacy and Advertising - done
Set powered off - Success - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered off - Success - setup
Initial settings completed
Client set connectable: Success (0x00)
Set powered off - Success - setup complete
Set powered off - Success - run
Registering new settings notification
Test condition added, total 1
Sending Set Powered (0x0005)
Test condition added, total 2
Set Powered (0x0005): Success (0x00)
Test condition complete, 1 left
New settings 0x00000080 received
Unregistering new settings notification
Test condition complete, 0 left
Set powered off - Success - test passed
Set powered off - Success - teardown
Index Removed callback
Index: 0x0000
Set powered off - Success - teardown complete
Set powered off - Success - done
Set powered off - Class of Device - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered off - Class of Device - setup
Setting device class and powering on Controller powered on
Client set connectable: Success (0x00)
Set powered off - Class of Device - setup complete Set powered off - Class of Device - run
Registering new settings notification Test condition added, total 1 Registering Class of Device Changed notification Test condition added, total 2
Sending Set Powered (0x0005)
Test condition added, total 3
Set Powered (0x0005): Success (0x00) Test condition complete, 2 left
New Class of Device Changed event received Test condition complete, 1 left
New settings 0x00000080 received Unregistering new settings notification Test condition complete, 0 left
Set powered off - Class of Device - test passed Set powered off - Class of Device - teardown
Index Removed callback
Index: 0x0000
Set powered off - Class of Device - teardown complete Set powered off - Class of Device - done
Set powered off - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered off - Invalid parameters 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set powered off - Invalid parameters 1 - setup complete Set powered off - Invalid parameters 1 - run
Sending Set Powered (0x0005)
Test condition added, total 1
Set Powered (0x0005): Invalid Parameters (0x0d) Test condition complete, 0 left
Set powered off - Invalid parameters 1 - test passed Set powered off - Invalid parameters 1 - teardown
Index Removed callback
Index: 0x0000
Set powered off - Invalid parameters 1 - teardown complete Set powered off - Invalid parameters 1 - done
Set powered off - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered off - Invalid parameters 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set powered off - Invalid parameters 2 - setup complete Set powered off - Invalid parameters 2 - run
Sending Set Powered (0x0005)
Test condition added, total 1
Set Powered (0x0005): Invalid Parameters (0x0d) Test condition complete, 0 left
Set powered off - Invalid parameters 2 - test passed Set powered off - Invalid parameters 2 - teardown
Index Removed callback
Index: 0x0000
Set powered off - Invalid parameters 2 - teardown complete Set powered off - Invalid parameters 2 - done
Set powered off - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered off - Invalid parameters 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set powered off - Invalid parameters 3 - setup complete Set powered off - Invalid parameters 3 - run
Sending Set Powered (0x0005)
Test condition added, total 1
Set Powered (0x0005): Invalid Parameters (0x0d) Test condition complete, 0 left
Set powered off - Invalid parameters 3 - test passed Set powered off - Invalid parameters 3 - teardown
Index Removed callback
Index: 0x0000
Set powered off - Invalid parameters 3 - teardown complete Set powered off - Invalid parameters 3 - done
Set connectable on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable on - Success 1 - setup
Set connectable on - Success 1 - setup complete
Set connectable on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Connectable (0x0007)
Test condition added, total 2
Set Connectable (0x0007): Success (0x00)
Test condition complete, 1 left
New settings 0x00000082 received
Unregistering new settings notification
Test condition complete, 0 left
Set connectable on - Success 1 - test passed
Set connectable on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set connectable on - Success 1 - teardown complete Set connectable on - Success 1 - done
Set connectable on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable on - Success 2 - setup complete
Set connectable on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Connectable (0x0007)
Test condition added, total 3
HCI Command 0x0c1a length 1
Test condition complete, 2 left
Set Connectable (0x0007): Success (0x00)
Test condition complete, 1 left
New settings 0x00000083 received
Unregistering new settings notification
Test condition complete, 0 left
Set connectable on - Success 2 - test passed
Set connectable on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable on - Success 2 - teardown complete Set connectable on - Success 2 - done
Set connectable on - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable on - Invalid parameters 1 - setup Set connectable on - Invalid parameters 1 - setup complete Set connectable on - Invalid parameters 1 - run
Sending Set Connectable (0x0007)
Test condition added, total 1
Set Connectable (0x0007): Invalid Parameters (0x0d) Test condition complete, 0 left
Set connectable on - Invalid parameters 1 - test passed Set connectable on - Invalid parameters 1 - teardown
Index Removed callback
Index: 0x0000
Set connectable on - Invalid parameters 1 - teardown complete Set connectable on - Invalid parameters 1 - done
Set connectable on - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable on - Invalid parameters 2 - setup Set connectable on - Invalid parameters 2 - setup complete Set connectable on - Invalid parameters 2 - run
Sending Set Connectable (0x0007)
Test condition added, total 1
Set Connectable (0x0007): Invalid Parameters (0x0d) Test condition complete, 0 left
Set connectable on - Invalid parameters 2 - test passed Set connectable on - Invalid parameters 2 - teardown
Index Removed callback
Index: 0x0000
Set connectable on - Invalid parameters 2 - teardown complete Set connectable on - Invalid parameters 2 - done
Set connectable on - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable on - Invalid parameters 3 - setup Set connectable on - Invalid parameters 3 - setup complete Set connectable on - Invalid parameters 3 - run
Sending Set Connectable (0x0007)
Test condition added, total 1
Set Connectable (0x0007): Invalid Parameters (0x0d) Test condition complete, 0 left
Set connectable on - Invalid parameters 3 - test passed Set connectable on - Invalid parameters 3 - teardown
Index Removed callback
Index: 0x0000
Set connectable on - Invalid parameters 3 - teardown complete Set connectable on - Invalid parameters 3 - done
Set connectable on - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable on - Invalid index - setup Set connectable on - Invalid index - setup complete Set connectable on - Invalid index - run
Sending Set Connectable (0x0007)
Test condition added, total 1
Set Connectable (0x0007): Invalid Index (0x11) Test condition complete, 0 left
Set connectable on - Invalid index - test passed Set connectable on - Invalid index - teardown
Index Removed callback
Index: 0x0000
Set connectable on - Invalid index - teardown complete Set connectable on - Invalid index - done
Set connectable on (LE) - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set connectable on (LE) - Success 1 - setup Set connectable on (LE) - Success 1 - setup complete Set connectable on (LE) - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Connectable (0x0007)
Test condition added, total 2
Set Connectable (0x0007): Success (0x00) Test condition complete, 1 left
New settings 0x00000202 received Unregistering new settings notification Test condition complete, 0 left
Set connectable on (LE) - Success 1 - test passed Set connectable on (LE) - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set connectable on (LE) - Success 1 - teardown complete Set connectable on (LE) - Success 1 - done
Set connectable on (LE) - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set connectable on (LE) - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable on (LE) - Success 2 - setup complete Set connectable on (LE) - Success 2 - run
Registering new settings notification
Test condition added, total 1
Sending Set Connectable (0x0007)
Test condition added, total 2
Set Connectable (0x0007): Success (0x00) Test condition complete, 1 left
New settings 0x00000203 received Unregistering new settings notification Test condition complete, 0 left
Set connectable on (LE) - Success 2 - test passed Set connectable on (LE) - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable on (LE) - Success 2 - teardown complete Set connectable on (LE) - Success 2 - done
Set connectable on (LE) - Success 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set connectable on (LE) - Success 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable on (LE) - Success 3 - setup complete Set connectable on (LE) - Success 3 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Connectable (0x0007)
Test condition added, total 3
HCI Command 0x200a length 1
HCI Command 0x2006 length 15
Test condition complete, 2 left
HCI Command 0x200a length 1
Set Connectable (0x0007): Success (0x00) Test condition complete, 1 left
New settings 0x00000603 received Unregistering new settings notification Test condition complete, 0 left
Set connectable on (LE) - Success 3 - test passed Set connectable on (LE) - Success 3 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable on (LE) - Success 3 - teardown complete Set connectable on (LE) - Success 3 - done
Set connectable off - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable off - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable off - Success 1 - setup complete
Set connectable off - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Connectable (0x0007)
Test condition added, total 2
Set Connectable (0x0007): Success (0x00)
Test condition complete, 1 left
New settings 0x00000080 received
Unregistering new settings notification
Test condition complete, 0 left
Set connectable off - Success 1 - test passed
Set connectable off - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set connectable off - Success 1 - teardown complete Set connectable off - Success 1 - done
Set connectable off - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable off - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable off - Success 2 - setup complete
Set connectable off - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Connectable (0x0007)
Test condition added, total 3
HCI Command 0x0c1a length 1
Test condition complete, 2 left
Set Connectable (0x0007): Success (0x00)
Test condition complete, 1 left
New settings 0x00000081 received
Unregistering new settings notification
Test condition complete, 0 left
Set connectable off - Success 2 - test passed
Set connectable off - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable off - Success 2 - teardown complete Set connectable off - Success 2 - done
Set connectable off - Success 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable off - Success 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable off - Success 3 - setup complete
Set connectable off - Success 3 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Connectable (0x0007)
Test condition added, total 3
HCI Command 0x0c1a length 1
Test condition complete, 2 left
Set Connectable (0x0007): Success (0x00)
Test condition complete, 1 left
New settings 0x00000081 received
Unregistering new settings notification
Test condition complete, 0 left
Set connectable off - Success 3 - test passed
Set connectable off - Success 3 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable off - Success 3 - teardown complete Set connectable off - Success 3 - done
Set connectable off - Success 4 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable off - Success 4 - setup
Initial settings completed
Powering on controller (with added device)
Controller powered on
Client set connectable: Success (0x00)
Set connectable off - Success 4 - setup complete
Set connectable off - Success 4 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Connectable (0x0007)
Test condition added, total 3
HCI Command 0x0c1a length 1
Test condition complete, 2 left
Set Connectable (0x0007): Success (0x00)
Test condition complete, 1 left
New settings 0x00000081 received
Unregistering new settings notification
Test condition complete, 0 left
Set connectable off - Success 4 - test passed
Set connectable off - Success 4 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable off - Success 4 - teardown complete Set connectable off - Success 4 - done
Set connectable off (LE) - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set connectable off (LE) - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable off (LE) - Success 1 - setup complete Set connectable off (LE) - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Connectable (0x0007)
Test condition added, total 2
Set Connectable (0x0007): Success (0x00) Test condition complete, 1 left
New settings 0x00000200 received Unregistering new settings notification Test condition complete, 0 left
Set connectable off (LE) - Success 1 - test passed Set connectable off (LE) - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set connectable off (LE) - Success 1 - teardown complete Set connectable off (LE) - Success 1 - done
Set connectable off (LE) - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set connectable off (LE) - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable off (LE) - Success 2 - setup complete Set connectable off (LE) - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Connectable (0x0007)
Test condition added, total 3
HCI Command 0x200a length 1
HCI Command 0x2005 length 6
HCI Command 0x2006 length 15
Test condition complete, 2 left
HCI Command 0x200a length 1
Set Connectable (0x0007): Success (0x00) Test condition complete, 1 left
New settings 0x00000601 received Unregistering new settings notification Test condition complete, 0 left
Set connectable off (LE) - Success 2 - test passed Set connectable off (LE) - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable off (LE) - Success 2 - teardown complete Set connectable off (LE) - Success 2 - done
Set connectable off (LE) - Success 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set connectable off (LE) - Success 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable off (LE) - Success 3 - setup complete Set connectable off (LE) - Success 3 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Connectable (0x0007)
Test condition added, total 3
HCI Command 0x2008 length 32
HCI Command 0x200a length 1
HCI Command 0x2005 length 6
HCI Command 0x2006 length 15
Test condition complete, 2 left
HCI Command 0x200a length 1
Set Connectable (0x0007): Success (0x00) Test condition complete, 1 left
New settings 0x00000601 received Unregistering new settings notification Test condition complete, 0 left
Set connectable off (LE) - Success 3 - test passed Set connectable off (LE) - Success 3 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable off (LE) - Success 3 - teardown complete Set connectable off (LE) - Success 3 - done
Set connectable off (LE) - Success 4 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set connectable off (LE) - Success 4 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable off (LE) - Success 4 - setup complete Set connectable off (LE) - Success 4 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Connectable (0x0007)
Test condition added, total 3
HCI Command 0x2008 length 32
HCI Command 0x200a length 1
HCI Command 0x2005 length 6
HCI Command 0x2006 length 15
Test condition complete, 2 left
HCI Command 0x200a length 1
Set Connectable (0x0007): Success (0x00) Test condition complete, 1 left
New settings 0x00000601 received Unregistering new settings notification Test condition complete, 0 left
Set connectable off (LE) - Success 4 - test passed Set connectable off (LE) - Success 4 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable off (LE) - Success 4 - teardown complete Set connectable off (LE) - Success 4 - done
Set fast connectable on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set fast connectable on - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set fast connectable on - Success 1 - setup complete Set fast connectable on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Fast Connectable (0x0008)
Test condition added, total 2
Set Fast Connectable (0x0008): Success (0x00) Test condition complete, 1 left
New settings 0x00000087 received Unregistering new settings notification Test condition complete, 0 left
Set fast connectable on - Success 1 - test passed Set fast connectable on - Success 1 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set fast connectable on - Success 1 - teardown complete Set fast connectable on - Success 1 - done
Set fast connectable on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set fast connectable on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set fast connectable on - Success 2 - setup complete Set fast connectable on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Sending Set Fast Connectable (0x0008)
Test condition added, total 2
Set Fast Connectable (0x0008): Success (0x00) Test condition complete, 1 left
New settings 0x00000085 received Unregistering new settings notification Test condition complete, 0 left
Set fast connectable on - Success 2 - test passed Set fast connectable on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set fast connectable on - Success 2 - teardown complete Set fast connectable on - Success 2 - done
Set fast connectable on - Success 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set fast connectable on - Success 3 - setup Set fast connectable on - Success 3 - setup complete Set fast connectable on - Success 3 - run
Registering new settings notification
Test condition added, total 1
Sending Set Fast Connectable (0x0008)
Test condition added, total 2
Set Fast Connectable (0x0008): Success (0x00) Test condition complete, 1 left
New settings 0x00000084 received Unregistering new settings notification Test condition complete, 0 left
Set fast connectable on - Success 3 - test passed Set fast connectable on - Success 3 - teardown
Index Removed callback
Index: 0x0000
Set fast connectable on - Success 3 - teardown complete Set fast connectable on - Success 3 - done
Set fast connectable on - Invalid Params 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set fast connectable on - Invalid Params 1 - setup Set fast connectable on - Invalid Params 1 - setup complete Set fast connectable on - Invalid Params 1 - run
Sending Set Fast Connectable (0x0008)
Test condition added, total 1
Set Fast Connectable (0x0008): Invalid Parameters (0x0d) Test condition complete, 0 left
Set fast connectable on - Invalid Params 1 - test passed Set fast connectable on - Invalid Params 1 - teardown
Index Removed callback
Index: 0x0000
Set fast connectable on - Invalid Params 1 - teardown complete Set fast connectable on - Invalid Params 1 - done
Set fast connectable on - Not Supported 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set fast connectable on - Not Supported 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set fast connectable on - Not Supported 1 - setup complete Set fast connectable on - Not Supported 1 - run
Sending Set Fast Connectable (0x0008)
Test condition added, total 1
Set Fast Connectable (0x0008): Not Supported (0x0c) Test condition complete, 0 left
Set fast connectable on - Not Supported 1 - test passed Set fast connectable on - Not Supported 1 - teardown
Index Removed callback
Index: 0x0000
Set fast connectable on - Not Supported 1 - teardown complete Set fast connectable on - Not Supported 1 - done
Set bondable on - Success - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set bondable on - Success - setup
Set bondable on - Success - setup complete
Set bondable on - Success - run
Registering new settings notification
Test condition added, total 1
Sending Set Bondable (0x0009)
Test condition added, total 2
Set Bondable (0x0009): Success (0x00)
Test condition complete, 1 left
New settings 0x00000090 received
Unregistering new settings notification
Test condition complete, 0 left
Set bondable on - Success - test passed
Set bondable on - Success - teardown
Index Removed callback
Index: 0x0000
Set bondable on - Success - teardown complete
Set bondable on - Success - done
Set bondable on - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set bondable on - Invalid parameters 1 - setup Set bondable on - Invalid parameters 1 - setup complete Set bondable on - Invalid parameters 1 - run
Sending Set Bondable (0x0009)
Test condition added, total 1
Set Bondable (0x0009): Invalid Parameters (0x0d) Test condition complete, 0 left
Set bondable on - Invalid parameters 1 - test passed Set bondable on - Invalid parameters 1 - teardown
Index Removed callback
Index: 0x0000
Set bondable on - Invalid parameters 1 - teardown complete Set bondable on - Invalid parameters 1 - done
Set bondable on - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set bondable on - Invalid parameters 2 - setup Set bondable on - Invalid parameters 2 - setup complete Set bondable on - Invalid parameters 2 - run
Sending Set Bondable (0x0009)
Test condition added, total 1
Set Bondable (0x0009): Invalid Parameters (0x0d) Test condition complete, 0 left
Set bondable on - Invalid parameters 2 - test passed Set bondable on - Invalid parameters 2 - teardown
Index Removed callback
Index: 0x0000
Set bondable on - Invalid parameters 2 - teardown complete Set bondable on - Invalid parameters 2 - done
Set bondable on - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set bondable on - Invalid parameters 3 - setup Set bondable on - Invalid parameters 3 - setup complete Set bondable on - Invalid parameters 3 - run
Sending Set Bondable (0x0009)
Test condition added, total 1
Set Bondable (0x0009): Invalid Parameters (0x0d) Test condition complete, 0 left
Set bondable on - Invalid parameters 3 - test passed Set bondable on - Invalid parameters 3 - teardown
Index Removed callback
Index: 0x0000
Set bondable on - Invalid parameters 3 - teardown complete Set bondable on - Invalid parameters 3 - done
Set bondable on - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set bondable on - Invalid index - setup
Set bondable on - Invalid index - setup complete
Set bondable on - Invalid index - run
Sending Set Bondable (0x0009)
Test condition added, total 1
Set Bondable (0x0009): Invalid Index (0x11)
Test condition complete, 0 left
Set bondable on - Invalid index - test passed
Set bondable on - Invalid index - teardown
Index Removed callback
Index: 0x0000
Set bondable on - Invalid index - teardown complete Set bondable on - Invalid index - done
Set discoverable on - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Invalid parameters 1 - setup Set discoverable on - Invalid parameters 1 - setup complete Set discoverable on - Invalid parameters 1 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Invalid Parameters (0x0d) Test condition complete, 0 left
Set discoverable on - Invalid parameters 1 - test passed Set discoverable on - Invalid parameters 1 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Invalid parameters 1 - teardown complete Set discoverable on - Invalid parameters 1 - done
Set discoverable on - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Invalid parameters 2 - setup Set discoverable on - Invalid parameters 2 - setup complete Set discoverable on - Invalid parameters 2 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Invalid Parameters (0x0d) Test condition complete, 0 left
Set discoverable on - Invalid parameters 2 - test passed Set discoverable on - Invalid parameters 2 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Invalid parameters 2 - teardown complete Set discoverable on - Invalid parameters 2 - done
Set discoverable on - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Invalid parameters 3 - setup Set discoverable on - Invalid parameters 3 - setup complete Set discoverable on - Invalid parameters 3 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Invalid Parameters (0x0d) Test condition complete, 0 left
Set discoverable on - Invalid parameters 3 - test passed Set discoverable on - Invalid parameters 3 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Invalid parameters 3 - teardown complete Set discoverable on - Invalid parameters 3 - done
Set discoverable on - Invalid parameters 4 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Invalid parameters 4 - setup Set discoverable on - Invalid parameters 4 - setup complete Set discoverable on - Invalid parameters 4 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Invalid Parameters (0x0d) Test condition complete, 0 left
Set discoverable on - Invalid parameters 4 - test passed Set discoverable on - Invalid parameters 4 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Invalid parameters 4 - teardown complete Set discoverable on - Invalid parameters 4 - done
Set discoverable on - Not powered 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Not powered 1 - setup Set discoverable on - Not powered 1 - setup complete Set discoverable on - Not powered 1 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Not Powered (0x0f) Test condition complete, 0 left
Set discoverable on - Not powered 1 - test passed Set discoverable on - Not powered 1 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Not powered 1 - teardown complete Set discoverable on - Not powered 1 - done
Set discoverable on - Not powered 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Not powered 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable on - Not powered 2 - setup complete Set discoverable on - Not powered 2 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Not Powered (0x0f) Test condition complete, 0 left
Set discoverable on - Not powered 2 - test passed Set discoverable on - Not powered 2 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Not powered 2 - teardown complete Set discoverable on - Not powered 2 - done
Set discoverable on - Rejected 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Rejected 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable on - Rejected 1 - setup complete
Set discoverable on - Rejected 1 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Rejected (0x0b)
Test condition complete, 0 left
Set discoverable on - Rejected 1 - test passed
Set discoverable on - Rejected 1 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Rejected 1 - teardown complete Set discoverable on - Rejected 1 - done
Set discoverable on - Rejected 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Rejected 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable on - Rejected 2 - setup complete
Set discoverable on - Rejected 2 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Rejected (0x0b)
Test condition complete, 0 left
Set discoverable on - Rejected 2 - test passed
Set discoverable on - Rejected 2 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Rejected 2 - teardown complete Set discoverable on - Rejected 2 - done
Set discoverable on - Rejected 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Rejected 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable on - Rejected 3 - setup complete
Set discoverable on - Rejected 3 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Rejected (0x0b)
Test condition complete, 0 left
Set discoverable on - Rejected 3 - test passed
Set discoverable on - Rejected 3 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Rejected 3 - teardown complete Set discoverable on - Rejected 3 - done
Set discoverable on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable on - Success 1 - setup complete
Set discoverable on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Discoverable (0x0006)
Test condition added, total 2
Set Discoverable (0x0006): Success (0x00)
Test condition complete, 1 left
New settings 0x0000008a received
Unregistering new settings notification
Test condition complete, 0 left
Set discoverable on - Success 1 - test passed
Set discoverable on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Success 1 - teardown complete Set discoverable on - Success 1 - done
Set discoverable on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable on - Success 2 - setup complete
Set discoverable on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Discoverable (0x0006)
Test condition added, total 3
HCI Command 0x0c3a length 4
HCI Command 0x0c1a length 1
Test condition complete, 2 left
Set Discoverable (0x0006): Success (0x00)
Test condition complete, 1 left
New settings 0x0000008b received
Unregistering new settings notification
Test condition complete, 0 left
Set discoverable on - Success 2 - test passed
Set discoverable on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set discoverable on - Success 2 - teardown complete Set discoverable on - Success 2 - done
Set discoverable on (LE) - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set discoverable on (LE) - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable on (LE) - Success 1 - setup complete Set discoverable on (LE) - Success 1 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Discoverable (0x0006)
Test condition added, total 2
HCI Command 0x2008 length 32
Test condition complete, 1 left
Set Discoverable (0x0006): Success (0x00) Test condition complete, 0 left
Set discoverable on (LE) - Success 1 - test passed Set discoverable on (LE) - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on (LE) - Success 1 - teardown complete Set discoverable on (LE) - Success 1 - done
Set discoverable off - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable off - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable off - Success 1 - setup complete
Set discoverable off - Success 1 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Success (0x00)
Test condition complete, 0 left
Set discoverable off - Success 1 - test passed
Set discoverable off - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set discoverable off - Success 1 - teardown complete Set discoverable off - Success 1 - done
Set discoverable off - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable off - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable off - Success 2 - setup complete
Set discoverable off - Success 2 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Discoverable (0x0006)
Test condition added, total 2
HCI Command 0x0c1a length 1
Test condition complete, 1 left
Set Discoverable (0x0006): Success (0x00)
Test condition complete, 0 left
Set discoverable off - Success 2 - test passed
Set discoverable off - Success 2 - teardown
Index Removed callback
Index: 0x0000
Set discoverable off - Success 2 - teardown complete Set discoverable off - Success 2 - done
Set limited discoverable on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set limited discoverable on - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set limited discoverable on - Success 1 - setup complete Set limited discoverable on - Success 1 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Discoverable (0x0006)
Test condition added, total 2
HCI Command 0x0c3a length 4
HCI Command 0x0c1a length 1
Test condition complete, 1 left
HCI Command 0x0c24 length 3
Set Discoverable (0x0006): Success (0x00) Test condition complete, 0 left
Set limited discoverable on - Success 1 - test passed Set limited discoverable on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set limited discoverable on - Success 1 - teardown complete Set limited discoverable on - Success 1 - done
Set limited discoverable on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set limited discoverable on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set limited discoverable on - Success 2 - setup complete Set limited discoverable on - Success 2 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Discoverable (0x0006)
Test condition added, total 2
HCI Command 0x0c3a length 4
Test condition complete, 1 left
HCI Command 0x0c1a length 1
HCI Command 0x0c24 length 3
Set Discoverable (0x0006): Success (0x00) Test condition complete, 0 left
Set limited discoverable on - Success 2 - test passed Set limited discoverable on - Success 2 - teardown
Index Removed callback
Index: 0x0000
Set limited discoverable on - Success 2 - teardown complete Set limited discoverable on - Success 2 - done
Set limited discoverable on - Success 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set limited discoverable on - Success 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set limited discoverable on - Success 3 - setup complete Set limited discoverable on - Success 3 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Discoverable (0x0006)
Test condition added, total 2
HCI Command 0x0c3a length 4
HCI Command 0x0c1a length 1
HCI Command 0x0c24 length 3
Test condition complete, 1 left
Set Discoverable (0x0006): Success (0x00) Test condition complete, 0 left
Set limited discoverable on - Success 3 - test passed Set limited discoverable on - Success 3 - teardown
Index Removed callback
Index: 0x0000
Set limited discoverable on - Success 3 - teardown complete Set limited discoverable on - Success 3 - done
Set limited discoverable on (LE) - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set limited discoverable on (LE) - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set limited discoverable on (LE) - Success 1 - setup complete Set limited discoverable on (LE) - Success 1 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Discoverable (0x0006)
Test condition added, total 2
HCI Command 0x2008 length 32
Test condition complete, 1 left
Set Discoverable (0x0006): Success (0x00)
Test condition complete, 0 left
Set limited discoverable on (LE) - Success 1 - test passed Set limited discoverable on (LE) - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set limited discoverable on (LE) - Success 1 - teardown complete Set limited discoverable on (LE) - Success 1 - done
Set link security on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security on - Success 1 - setup
Set link security on - Success 1 - setup complete
Set link security on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Link Security (0x000a)
Test condition added, total 2
Set Link Security (0x000a): Success (0x00)
Test condition complete, 1 left
New settings 0x000000a0 received
Unregistering new settings notification
Test condition complete, 0 left
Set link security on - Success 1 - test passed
Set link security on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set link security on - Success 1 - teardown complete Set link security on - Success 1 - done
Set link security on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set link security on - Success 2 - setup complete
Set link security on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Link Security (0x000a)
Test condition added, total 3
HCI Command 0x0c20 length 1
Test condition complete, 2 left
Set Link Security (0x000a): Success (0x00)
Test condition complete, 1 left
New settings 0x000000a1 received
Unregistering new settings notification
Test condition complete, 0 left
Set link security on - Success 2 - test passed
Set link security on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set link security on - Success 2 - teardown complete Set link security on - Success 2 - done
Set link security on - Success 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security on - Success 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set link security on - Success 3 - setup complete
Set link security on - Success 3 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Powered (0x0005)
Test condition added, total 3
HCI Command 0x0c20 length 1
Test condition complete, 2 left
HCI Command 0x0c13 length 248
Set Powered (0x0005): Success (0x00)
Test condition complete, 1 left
New settings 0x000000a1 received
Unregistering new settings notification
Test condition complete, 0 left
Set link security on - Success 3 - test passed
Set link security on - Success 3 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set link security on - Success 3 - teardown complete Set link security on - Success 3 - done
Set link security on - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security on - Invalid parameters 1 - setup Set link security on - Invalid parameters 1 - setup complete Set link security on - Invalid parameters 1 - run
Sending Set Link Security (0x000a)
Test condition added, total 1
Set Link Security (0x000a): Invalid Parameters (0x0d) Test condition complete, 0 left
Set link security on - Invalid parameters 1 - test passed Set link security on - Invalid parameters 1 - teardown
Index Removed callback
Index: 0x0000
Set link security on - Invalid parameters 1 - teardown complete Set link security on - Invalid parameters 1 - done
Set link security on - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security on - Invalid parameters 2 - setup Set link security on - Invalid parameters 2 - setup complete Set link security on - Invalid parameters 2 - run
Sending Set Link Security (0x000a)
Test condition added, total 1
Set Link Security (0x000a): Invalid Parameters (0x0d) Test condition complete, 0 left
Set link security on - Invalid parameters 2 - test passed Set link security on - Invalid parameters 2 - teardown
Index Removed callback
Index: 0x0000
Set link security on - Invalid parameters 2 - teardown complete Set link security on - Invalid parameters 2 - done
Set link security on - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security on - Invalid parameters 3 - setup Set link security on - Invalid parameters 3 - setup complete Set link security on - Invalid parameters 3 - run
Sending Set Link Security (0x000a)
Test condition added, total 1
Set Link Security (0x000a): Invalid Parameters (0x0d) Test condition complete, 0 left
Set link security on - Invalid parameters 3 - test passed Set link security on - Invalid parameters 3 - teardown
Index Removed callback
Index: 0x0000
Set link security on - Invalid parameters 3 - teardown complete Set link security on - Invalid parameters 3 - done
Set link security on - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security on - Invalid index - setup Set link security on - Invalid index - setup complete Set link security on - Invalid index - run
Sending Set Link Security (0x000a)
Test condition added, total 1
Set Link Security (0x000a): Invalid Index (0x11) Test condition complete, 0 left
Set link security on - Invalid index - test passed Set link security on - Invalid index - teardown
Index Removed callback
Index: 0x0000
Set link security on - Invalid index - teardown complete Set link security on - Invalid index - done
Set link security off - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security off - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set link security off - Success 1 - setup complete Set link security off - Success 1 - run
Registering new settings notification Test condition added, total 1
Sending Set Link Security (0x000a)
Test condition added, total 2
Set Link Security (0x000a): Success (0x00) Test condition complete, 1 left
New settings 0x00000080 received Unregistering new settings notification Test condition complete, 0 left
Set link security off - Success 1 - test passed Set link security off - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set link security off - Success 1 - teardown complete Set link security off - Success 1 - done
Set link security off - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security off - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set link security off - Success 2 - setup complete Set link security off - Success 2 - run
Registering new settings notification Test condition added, total 1 Registering HCI command callback
Test condition added, total 2
Sending Set Link Security (0x000a)
Test condition added, total 3
HCI Command 0x0c20 length 1
Test condition complete, 2 left
Set Link Security (0x000a): Success (0x00) Test condition complete, 1 left
New settings 0x00000081 received Unregistering new settings notification Test condition complete, 0 left
Set link security off - Success 2 - test passed Set link security off - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set link security off - Success 2 - teardown complete Set link security off - Success 2 - done
Set SSP on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set SSP on - Success 1 - setup
Set SSP on - Success 1 - setup complete
Set SSP on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Secure Simple Pairing (0x000b) Test condition added, total 2
Set Secure Simple Pairing (0x000b): Success (0x00) Test condition complete, 1 left
New settings 0x000000c0 received Unregistering new settings notification Test condition complete, 0 left
Set SSP on - Success 1 - test passed
Set SSP on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set SSP on - Success 1 - teardown complete
Set SSP on - Success 1 - done
Set SSP on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set SSP on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set SSP on - Success 2 - setup complete
Set SSP on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Secure Simple Pairing (0x000b) Test condition added, total 3
HCI Command 0x0c56 length 1
Test condition complete, 2 left
Set Secure Simple Pairing (0x000b): Success (0x00) Test condition complete, 1 left
New settings 0x000000c1 received Unregistering new settings notification Test condition complete, 0 left
Set SSP on - Success 2 - test passed
HCI Command 0x0c52 length 241
Set SSP on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set SSP on - Success 2 - teardown complete
Set SSP on - Success 2 - done
Set SSP on - Success 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set SSP on - Success 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set SSP on - Success 3 - setup complete
Set SSP on - Success 3 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Powered (0x0005)
Test condition added, total 3
HCI Command 0x0c56 length 1
Test condition complete, 2 left
HCI Command 0x0c13 length 248
HCI Command 0x0c52 length 241
Set Powered (0x0005): Success (0x00)
Test condition complete, 1 left
New settings 0x000000c1 received
Unregistering new settings notification
Test condition complete, 0 left
Set SSP on - Success 3 - test passed
Set SSP on - Success 3 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set SSP on - Success 3 - teardown complete
Set SSP on - Success 3 - done
Set SSP on - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set SSP on - Invalid parameters 1 - setup
Set SSP on - Invalid parameters 1 - setup complete Set SSP on - Invalid parameters 1 - run
Sending Set Secure Simple Pairing (0x000b)
Test condition added, total 1
Set Secure Simple Pairing (0x000b): Invalid Parameters (0x0d) Test condition complete, 0 left
Set SSP on - Invalid parameters 1 - test passed
Set SSP on - Invalid parameters 1 - teardown
Index Removed callback
Index: 0x0000
Set SSP on - Invalid parameters 1 - teardown complete Set SSP on - Invalid parameters 1 - done
Set SSP on - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set SSP on - Invalid parameters 2 - setup
Set SSP on - Invalid parameters 2 - setup complete Set SSP on - Invalid parameters 2 - run
Sending Set Secure Simple Pairing (0x000b)
Test condition added, total 1
Set Secure Simple Pairing (0x000b): Invalid Parameters (0x0d) Test condition complete, 0 left
Set SSP on - Invalid parameters 2 - test passed
Set SSP on - Invalid parameters 2 - teardown
Index Removed callback
Index: 0x0000
Set SSP on - Invalid parameters 2 - teardown complete Set SSP on - Invalid parameters 2 - done
Set SSP on - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set SSP on - Invalid parameters 3 - setup
Set SSP on - Invalid parameters 3 - setup complete Set SSP on - Invalid parameters 3 - run
Sending Set Secure Simple Pairing (0x000b)
Test condition added, total 1
Set Secure Simple Pairing (0x000b): Invalid Parameters (0x0d) Test condition complete, 0 left
Set SSP on - Invalid parameters 3 - test passed
Set SSP on - Invalid parameters 3 - teardown
Index Removed callback
Index: 0x0000
Set SSP on - Invalid parameters 3 - teardown complete Set SSP on - Invalid parameters 3 - done
Set SSP on - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set SSP on - Invalid index - setup
Set SSP on - Invalid index - setup complete
Set SSP on - Invalid index - run
Sending Set Secure Simple Pairing (0x000b)
Test condition added, total 1
Set Secure Simple Pairing (0x000b): Invalid Index (0x11) Test condition complete, 0 left
Set SSP on - Invalid index - test passed
Set SSP on - Invalid index - teardown
Index Removed callback
Index: 0x0000
Set SSP on - Invalid index - teardown complete
Set SSP on - Invalid index - done
Set Secure Connections on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections on - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections on - Success 1 - setup complete Set Secure Connections on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Secure Connections (0x002d) Test condition added, total 2
Set Secure Connections (0x002d): Success (0x00) Test condition complete, 1 left
New settings 0x000008c0 received Unregistering new settings notification Test condition complete, 0 left
Set Secure Connections on - Success 1 - test passed Set Secure Connections on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set Secure Connections on - Success 1 - teardown complete Set Secure Connections on - Success 1 - done
Set Secure Connections on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections on - Success 2 - setup complete Set Secure Connections on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Secure Connections (0x002d) Test condition added, total 3
HCI Command 0x0c7a length 1
Test condition complete, 2 left
Set Secure Connections (0x002d): Success (0x00) Test condition complete, 1 left
New settings 0x000008c1 received Unregistering new settings notification Test condition complete, 0 left
Set Secure Connections on - Success 2 - test passed Set Secure Connections on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set Secure Connections on - Success 2 - teardown complete Set Secure Connections on - Success 2 - done
Set Secure Connections on - Invalid params 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections on - Invalid params 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections on - Invalid params 1 - setup complete Set Secure Connections on - Invalid params 1 - run
Sending Set Secure Connections (0x002d)
Test condition added, total 1
Set Secure Connections (0x002d): Invalid Parameters (0x0d) Test condition complete, 0 left
Set Secure Connections on - Invalid params 1 - test passed Set Secure Connections on - Invalid params 1 - teardown
Index Removed callback
Index: 0x0000
Set Secure Connections on - Invalid params 1 - teardown complete Set Secure Connections on - Invalid params 1 - done
Set Secure Connections on - Invalid params 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections on - Invalid params 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections on - Invalid params 2 - setup complete Set Secure Connections on - Invalid params 2 - run
Sending Set Secure Connections (0x002d)
Test condition added, total 1
Set Secure Connections (0x002d): Invalid Parameters (0x0d) Test condition complete, 0 left
Set Secure Connections on - Invalid params 2 - test passed Set Secure Connections on - Invalid params 2 - teardown
Index Removed callback
Index: 0x0000
Set Secure Connections on - Invalid params 2 - teardown complete Set Secure Connections on - Invalid params 2 - done
Set Secure Connections on - Invalid params 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections on - Invalid params 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections on - Invalid params 3 - setup complete Set Secure Connections on - Invalid params 3 - run
Sending Set Secure Connections (0x002d)
Test condition added, total 1
Set Secure Connections (0x002d): Invalid Parameters (0x0d) Test condition complete, 0 left
Set Secure Connections on - Invalid params 3 - test passed Set Secure Connections on - Invalid params 3 - teardown
Index Removed callback
Index: 0x0000
Set Secure Connections on - Invalid params 3 - teardown complete Set Secure Connections on - Invalid params 3 - done
Set Secure Connections on - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections on - Invalid index - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections on - Invalid index - setup complete Set Secure Connections on - Invalid index - run
Sending Set Secure Connections (0x002d)
Test condition added, total 1
Set Secure Connections (0x002d): Invalid Index (0x11) Test condition complete, 0 left
Set Secure Connections on - Invalid index - test passed Set Secure Connections on - Invalid index - teardown
Index Removed callback
Index: 0x0000
Set Secure Connections on - Invalid index - teardown complete Set Secure Connections on - Invalid index - done
Set Secure Connections on - Not supported 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections on - Not supported 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections on - Not supported 1 - setup complete Set Secure Connections on - Not supported 1 - run
Sending Set Secure Connections (0x002d)
Test condition added, total 1
Set Secure Connections (0x002d): Not Supported (0x0c) Test condition complete, 0 left
Set Secure Connections on - Not supported 1 - test passed Set Secure Connections on - Not supported 1 - teardown
Index Removed callback
Index: 0x0000
Set Secure Connections on - Not supported 1 - teardown complete Set Secure Connections on - Not supported 1 - done
Set Secure Connections on - Not supported 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections on - Not supported 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections on - Not supported 2 - setup complete Set Secure Connections on - Not supported 2 - run
Sending Set Secure Connections (0x002d)
Test condition added, total 1
Set Secure Connections (0x002d): Not Supported (0x0c) Test condition complete, 0 left
Set Secure Connections on - Not supported 2 - test passed Set Secure Connections on - Not supported 2 - teardown
Index Removed callback
Index: 0x0000
Set Secure Connections on - Not supported 2 - teardown complete Set Secure Connections on - Not supported 2 - done
Set Secure Connections Only on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections Only on - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections Only on - Success 1 - setup complete Set Secure Connections Only on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Secure Connections (0x002d)
Test condition added, total 2
Set Secure Connections (0x002d): Success (0x00) Test condition complete, 1 left
New settings 0x000008c0 received
Unregistering new settings notification
Test condition complete, 0 left
Set Secure Connections Only on - Success 1 - test passed Set Secure Connections Only on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set Secure Connections Only on - Success 1 - teardown complete Set Secure Connections Only on - Success 1 - done
Set Secure Connections Only on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections Only on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections Only on - Success 2 - setup complete Set Secure Connections Only on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Secure Connections (0x002d)
Test condition added, total 3
HCI Command 0x0c7a length 1
Test condition complete, 2 left
Set Secure Connections (0x002d): Success (0x00) Test condition complete, 1 left
New settings 0x000008c1 received
Unregistering new settings notification
Test condition complete, 0 left
Set Secure Connections Only on - Success 2 - test passed Set Secure Connections Only on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set Secure Connections Only on - Success 2 - teardown complete Set Secure Connections Only on - Success 2 - done
Set High Speed on - Success - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Expected bit 8 not supported
Expected supported settings: 0x0001beff != 0x0001bfff
Set High Speed on - Success - pre setup failed
Index Removed callback
Index: 0x0000
Set High Speed on - Success - done
Set High Speed on - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Expected bit 8 not supported
Expected supported settings: 0x0001beff != 0x0001bfff
Set High Speed on - Invalid parameters 1 - pre setup failed
Index Removed callback
Index: 0x0000
Set High Speed on - Invalid parameters 1 - done
Set High Speed on - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Expected bit 8 not supported
Expected supported settings: 0x0001beff != 0x0001bfff
Set High Speed on - Invalid parameters 2 - pre setup failed
Index Removed callback
Index: 0x0000
Set High Speed on - Invalid parameters 2 - done
Set High Speed on - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Expected bit 8 not supported
Expected supported settings: 0x0001beff != 0x0001bfff
Set High Speed on - Invalid parameters 3 - pre setup failed
Index Removed callback
Index: 0x0000
Set High Speed on - Invalid parameters 3 - done
Set High Speed on - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Expected bit 8 not supported
Expected supported settings: 0x0001beff != 0x0001bfff
Set High Speed on - Invalid index - pre setup failed
Index Removed callback
Index: 0x0000
Set High Speed on - Invalid index - done
Set Low Energy on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Low Energy on - Success 1 - setup
Set Low Energy on - Success 1 - setup complete
Set Low Energy on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Low Energy (0x000d)
Test condition added, total 2
Set Low Energy (0x000d): Success (0x00)
Test condition complete, 1 left
New settings 0x00000280 received
Unregistering new settings notification
Test condition complete, 0 left
Set Low Energy on - Success 1 - test passed
Set Low Energy on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set Low Energy on - Success 1 - teardown complete
Set Low Energy on - Success 1 - done
Set Low Energy on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Low Energy on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Low Energy on - Success 2 - setup complete
Set Low Energy on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Low Energy (0x000d)
Test condition added, total 3
HCI Command 0x0c6d length 2
Test condition complete, 2 left
Set Low Energy (0x000d): Success (0x00)
Test condition complete, 1 left
New settings 0x00000281 received
Unregistering new settings notification
Test condition complete, 0 left
Set Low Energy on - Success 2 - test passed
HCI Command 0x2008 length 32
Set Low Energy on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set Low Energy on - Success 2 - teardown complete
Set Low Energy on - Success 2 - done
Set Low Energy on - Success 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Low Energy on - Success 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Low Energy on - Success 3 - setup complete
Set Low Energy on - Success 3 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Powered (0x0005)
Test condition added, total 3
HCI Command 0x0c6d length 2
Test condition complete, 2 left
HCI Command 0x2008 length 32
HCI Command 0x0c13 length 248
Set Powered (0x0005): Success (0x00)
Test condition complete, 1 left
New settings 0x00000281 received
Unregistering new settings notification
Test condition complete, 0 left
Set Low Energy on - Success 3 - test passed
Set Low Energy on - Success 3 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set Low Energy on - Success 3 - teardown complete
Set Low Energy on - Success 3 - done
Set Low Energy on - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Low Energy on - Invalid parameters 1 - setup Set Low Energy on - Invalid parameters 1 - setup complete Set Low Energy on - Invalid parameters 1 - run
Sending Set Low Energy (0x000d)
Test condition added, total 1
Set Low Energy (0x000d): Invalid Parameters (0x0d) Test condition complete, 0 left
Set Low Energy on - Invalid parameters 1 - test passed Set Low Energy on - Invalid parameters 1 - teardown
Index Removed callback
Index: 0x0000
Set Low Energy on - Invalid parameters 1 - teardown complete Set Low Energy on - Invalid parameters 1 - done
Set Low Energy on - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Low Energy on - Invalid parameters 2 - setup Set Low Energy on - Invalid parameters 2 - setup complete Set Low Energy on - Invalid parameters 2 - run
Sending Set Low Energy (0x000d)
Test condition added, total 1
Set Low Energy (0x000d): Invalid Parameters (0x0d) Test condition complete, 0 left
Set Low Energy on - Invalid parameters 2 - test passed Set Low Energy on - Invalid parameters 2 - teardown
Index Removed callback
Index: 0x0000
Set Low Energy on - Invalid parameters 2 - teardown complete Set Low Energy on - Invalid parameters 2 - done
Set Low Energy on - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Low Energy on - Invalid parameters 3 - setup Set Low Energy on - Invalid parameters 3 - setup complete Set Low Energy on - Invalid parameters 3 - run
Sending Set Low Energy (0x000d)
Test condition added, total 1
Set Low Energy (0x000d): Invalid Parameters (0x0d) Test condition complete, 0 left
Set Low Energy on - Invalid parameters 3 - test passed Set Low Energy on - Invalid parameters 3 - teardown
Index Removed callback
Index: 0x0000
Set Low Energy on - Invalid parameters 3 - teardown complete Set Low Energy on - Invalid parameters 3 - done
Set Low Energy on - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Low Energy on - Invalid index - setup Set Low Energy on - Invalid index - setup complete Set Low Energy on - Invalid index - run
Sending Set Low Energy (0x000d)
Test condition added, total 1
Set Low Energy (0x000d): Invalid Index (0x11) Test condition complete, 0 left
Set Low Energy on - Invalid index - test passed Set Low Energy on - Invalid index - teardown
Index Removed callback
Index: 0x0000
Set Low Energy on - Invalid index - teardown complete Set Low Energy on - Invalid index - done
Set Advertising on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Advertising on - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Advertising on - Success 1 - setup complete
Set Advertising on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Advertising (0x0029)
Test condition added, total 2
Set Advertising (0x0029): Success (0x00)
Test condition complete, 1 left
New settings 0x00000680 received
Unregistering new settings notification
Test condition complete, 0 left
Set Advertising on - Success 1 - test passed
Set Advertising on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set Advertising on - Success 1 - teardown complete Set Advertising on - Success 1 - done
Set Advertising on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Advertising on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Advertising on - Success 2 - setup complete
Set Advertising on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Advertising (0x0029)
Test condition added, total 3
HCI Command 0x2005 length 6
HCI Command 0x2006 length 15
HCI Command 0x200a length 1
Test condition complete, 2 left
Set Advertising (0x0029): Success (0x00)
Test condition complete, 1 left
New settings 0x00000681 received
Unregistering new settings notification
Test condition complete, 0 left
Set Advertising on - Success 2 - test passed
Set Advertising on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set Advertising on - Success 2 - teardown complete Set Advertising on - Success 2 - done
Set Advertising on - Rejected 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Advertising on - Rejected 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Advertising on - Rejected 1 - setup complete
Set Advertising on - Rejected 1 - run
Sending Set Advertising (0x0029)
Test condition added, total 1
Set Advertising (0x0029): Rejected (0x0b)
Test condition complete, 0 left
Set Advertising on - Rejected 1 - test passed
Set Advertising on - Rejected 1 - teardown
Index Removed callback
Index: 0x0000
Set Advertising on - Rejected 1 - teardown complete Set Advertising on - Rejected 1 - done
Set Advertising on - Appearance 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Advertising on - Appearance 1 - setup
Initial settings completed
Setup sending Set Appearance (0x0043) Test setup condition added, total 1
Test setup condition complete, 0 left
Set Advertising on - Appearance 1 - setup complete Set Advertising on - Appearance 1 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Advertising (0x0029)
Test condition added, total 2
HCI Command 0x2009 length 32
Test condition complete, 1 left
HCI Command 0x2005 length 6
HCI Command 0x2006 length 15
HCI Command 0x200a length 1
Set Advertising (0x0029): Success (0x00) Test condition complete, 0 left
Set Advertising on - Appearance 1 - test passed Set Advertising on - Appearance 1 - teardown
Index Removed callback
Index: 0x0000
Set Advertising on - Appearance 1 - teardown complete Set Advertising on - Appearance 1 - done
Set Advertising on - Local name 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Advertising on - Local name 1 - setup
Initial settings completed
Setup sending Set Local Name (0x000f) Test setup condition added, total 1
Test setup condition complete, 0 left
Set Advertising on - Local name 1 - setup complete Set Advertising on - Local name 1 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Advertising (0x0029)
Test condition added, total 2
HCI Command 0x2009 length 32
Test condition complete, 1 left
HCI Command 0x2005 length 6
HCI Command 0x2006 length 15
HCI Command 0x200a length 1
Set Advertising (0x0029): Success (0x00) Test condition complete, 0 left
Set Advertising on - Local name 1 - test passed Set Advertising on - Local name 1 - teardown
Index Removed callback
Index: 0x0000
Set Advertising on - Local name 1 - teardown complete Set Advertising on - Local name 1 - done
Set Advertising on - Name + Appear 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Advertising on - Name + Appear 1 - setup
Initial settings completed
Sending setup opcode array
Setup sending Set Appearance (0x0043)
Test setup condition added, total 1
Setup sending Set Local Name (0x000f)
Test setup condition added, total 2
Test setup condition complete, 1 left
Test setup condition complete, 0 left
Set Advertising on - Name + Appear 1 - setup complete Set Advertising on - Name + Appear 1 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Advertising (0x0029)
Test condition added, total 2
HCI Command 0x2009 length 32
Test condition complete, 1 left
HCI Command 0x2005 length 6
HCI Command 0x2006 length 15
HCI Command 0x200a length 1
Set Advertising (0x0029): Success (0x00) Test condition complete, 0 left
Set Advertising on - Name + Appear 1 - test passed Set Advertising on - Name + Appear 1 - teardown
Index Removed callback
Index: 0x0000
Set Advertising on - Name + Appear 1 - teardown complete Set Advertising on - Name + Appear 1 - done
Set BR/EDR off - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set BR/EDR off - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set BR/EDR off - Success 1 - setup complete
Set BR/EDR off - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set BR/EDR (0x002a)
Test condition added, total 2
Set BR/EDR (0x002a): Success (0x00)
Test condition complete, 1 left
New settings 0x00000200 received
Unregistering new settings notification
Test condition complete, 0 left
Set BR/EDR off - Success 1 - test passed
Set BR/EDR off - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set BR/EDR off - Success 1 - teardown complete
Set BR/EDR off - Success 1 - done
Set BR/EDR on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set BR/EDR on - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set BR/EDR on - Success 1 - setup complete
Set BR/EDR on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set BR/EDR (0x002a)
Test condition added, total 2
Set BR/EDR (0x002a): Success (0x00)
Test condition complete, 1 left
New settings 0x00000280 received
Unregistering new settings notification
Test condition complete, 0 left
Set BR/EDR on - Success 1 - test passed
Set BR/EDR on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set BR/EDR on - Success 1 - teardown complete
Set BR/EDR on - Success 1 - done
Set BR/EDR on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback11 lines not shown · raw message
13,126 lines not shown · raw message
Part of this message is not shown here. View the raw message.
Re: [PATCH v2 1/3] Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750
In reply to Venkata Lakshmi Narayana GubbaQuoted 78 lines · Venkata Lakshmi Narayana Gubba
Added regulators,GPIOs and changes required to power on/off wcn6750. Added support for firmware download for wcn6750.
Changes done in detail:
1. Added regulators and corresponding current values.
2. Addedsw_ctrlGPIO pin which is output from BT SoC and indicates status of clock supply to BT SoC.
3. Added inline function to check if the SoC type is wcn399x or wcn6750.
4. Modified the functionqca_wcn3990_init()to support wcn6750 and renamed it toqca_regulator_init().
5. AddedBT_ONandBT_OFFmacros.
6. Added support to download mbn type firmware image as wcn6750 supports mbn type image.
7. If mbn type image is not present then we will check for tlv type image.
8. Moved extracting rom version info to common place as this code is common in all if else ladder inqca_uart_setup.Signed-off-by Venkata Lakshmi Narayana Gubba <[email protected]>--- drivers/bluetooth/btqca.c | 88 ++++++++++++++++++++++++++---------- drivers/bluetooth/btqca.h | 15 ++++++- drivers/bluetooth/hci_qca.c | 106 ++++++++++++++++++++++++++++++++++---------- 3 files changed, 161 insertions(+), 48 deletions(-)drivers/bluetooth/btqca.c +13
-9@@ -182,7 +182,8 @@ int qca_send_pre_shutdown_cmd(struct hci_dev *hdev) }EXPORT_SYMBOL_GPL (qca_send_pre_shutdown_cmd); -static void qca_tlv_check_data (struct qca_fw_config *config, +static void qca_tlv_check_data (struct hci_dev *hdev, +struct qca_fw_config *config,const struct firmware *fw,enum qca_btsoc_type soc_type) {const u8 *data;@@ -194,19 +195,21 @@ static void qca_tlv_check_data(struct qca_fw_config *config,struct tlv_type_nvm *tlv_nvm;uint8_t nvm_baud_rate = config->user_baud_rate; - tlv = (struct tlv_type_hdr *)fw->data; - - type_len =le32_to_cpu (tlv->type_len); - length = (type_len >>8 ) &0x00ffffff ; - -BT_DBG ("TLV Type\t\t : 0x%x" , type_len &0x000000ff ); -BT_DBG ("Length\t\t : %d bytes" , length); - config->dnld_mode =QCA_SKIP_EVT_NONE ; config->dnld_type =QCA_SKIP_EVT_NONE ;switch (config->type) { +case ELF_TYPE_PATCH : + config->dnld_mode =QCA_SKIP_EVT_VSE_CC ; + config->dnld_type =QCA_SKIP_EVT_VSE_CC ; + +bt_dev_dbg (hdev,"File Class : 0x%x" , fw->data[4 ]); +bt_dev_dbg (hdev,"Data Encoding : 0x%x" , fw->data[5 ]); +bt_dev_dbg (hdev,"File version : 0x%x" , fw->data[6 ]); +break ;case TLV_TYPE_PATCH : + tlv = (struct tlv_type_hdr *)fw->data; + type_len =le32_to_cpu (tlv->type_len); tlv_patch = (struct tlv_type_patch *)tlv->data;/* For Rome version 1.1 to 3.1, all segment commands @@ -218,6 +221,7 @@ static void qca_tlv_check_data(struct qca_fw_config *config, config->dnld_mode = tlv_patch->download_mode; config->dnld_type = config->dnld_mode; +BT_DBG ("TLV Type\t\t : 0x%x" , type_len &0x000000ff );BT_DBG ("Total Length : %d bytes" ,le32_to_cpu (tlv_patch->total_size)); BT_DBG("Patch Data Length : %d bytes",@@ -243,6 +247,14 @@ static void qca_tlv_check_data(struct qca_fw_config *config,break ;
drivers/bluetooth/btqca.c static void qca_tlv_check_data(struct qca_fw_config *config, · line 257
Quoted 10 lines
drivers/bluetooth/btqca.c +8
-0case TLV_TYPE_NVM : + tlv = (struct tlv_type_hdr *)fw->data; + + type_len =le32_to_cpu (tlv->type_len); + length = (type_len >>8 ) &0x00ffffff ; + +BT_DBG ("TLV Type\t\t : 0x%x" , type_len &0x000000ff ); +BT_DBG ("Length\t\t : %d bytes" , length); +
To keep the wcn6750 shorther you could consider to have a separate patch for the ELF type and the additional logging.
Quoted 48 lines
drivers/bluetooth/btqca.c +23
-5idx =0 ; data = tlv->data;while (idx < length) {@@ -387,7 +399,8 @@ static int qca_inject_cmd_complete_event(struct hci_dev *hdev)static int qca_download_firmware (struct hci_dev *hdev,struct qca_fw_config *config, -enum qca_btsoc_type soc_type) +enum qca_btsoc_type soc_type, +u8 rom_ver) {const struct firmware *fw;const u8 *segment;@@ -397,12 +410,29 @@ static int qca_download_firmware(struct hci_dev *hdev, ret =request_firmware (&fw, config->fwname, &hdev->dev);if (ret) { -bt_dev_err (hdev,"QCA Failed to request file: %s (%d)" , - config->fwname, ret); -return ret; +/* For WCN6750, if mbn file is not present then check for +* tlv file. +*/ +if (soc_type ==QCA_WCN6750 && config->type ==ELF_TYPE_PATCH ) { +bt_dev_dbg (hdev,"QCA Failed to request file: %s (%d)" , + config->fwname, ret); + config->type =TLV_TYPE_PATCH ; +snprintf (config->fwname,sizeof (config->fwname), +"qca/msbtfw%02x.tlv" , rom_ver); + ret =request_firmware (&fw, config->fwname, &hdev->dev); +if (ret) { +bt_dev_err (hdev,"QCA Failed to request file: %s (%d)" , + config->fwname, ret); +return ret; + } + }else { +bt_dev_err (hdev,"QCA Failed to request file: %s (%d)" , + config->fwname, ret); +return ret; + } } -qca_tlv_check_data (config, fw, soc_type); +qca_tlv_check_data (hdev, config, fw, soc_type); segment = fw->data; remain = fw->size;
drivers/bluetooth/btqca.c int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate, · line 540
Quoted 9 lines
drivers/bluetooth/btqca.c +6
-0@@ -502,27 +532,33 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate, config.user_baud_rate = baudrate; +/* Firmware files to download are based on ROM version. +* ROM version is derived from last two bytes of soc_ver. +*/ + rom_ver = ((soc_ver &0x00000f00 ) >>0x04 ) | + (soc_ver &0x0000000f ); +
This refactoring could also be done in a separate patch.
Quoted 87 lines
drivers/bluetooth/btqca.c +14
-10/* Download rampatch file */ config.type =TLV_TYPE_PATCH ;if (qca_is_wcn399x (soc_type)) { -/* Firmware files to download are based on ROM version. -* ROM version is derived from last two bytes of soc_ver. -*/ - rom_ver = ((soc_ver &0x00000f00 ) >>0x04 ) | - (soc_ver &0x0000000f );snprintf (config.fwname,sizeof (config.fwname),"qca/crbtfw%02x.tlv" , rom_ver); }else if (soc_type ==QCA_QCA6390 ) { - rom_ver = ((soc_ver &0x00000f00 ) >>0x04 ) | - (soc_ver &0x0000000f );snprintf (config.fwname,sizeof (config.fwname),"qca/htbtfw%02x.tlv" , rom_ver); + }else if (soc_type ==QCA_WCN6750 ) { +/* Choose mbn file by default.If mbn file is not found +* then choose tlv file +*/ + config.type =ELF_TYPE_PATCH ; +snprintf (config.fwname,sizeof (config.fwname), +"qca/msbtfw%02x.mbn" , rom_ver); }else {snprintf (config.fwname,sizeof (config.fwname),"qca/rampatch_%08x.bin" , soc_ver); } - err =qca_download_firmware (hdev, &config, soc_type); + err =qca_download_firmware (hdev, &config, soc_type, rom_ver);if (err <0 ) {bt_dev_err (hdev,"QCA Failed to download patch (%d)" , err);return err;@@ -548,11 +584,14 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,else if (soc_type ==QCA_QCA6390 )snprintf (config.fwname,sizeof (config.fwname),"qca/htnv%02x.bin" , rom_ver); +else if (soc_type ==QCA_WCN6750 ) +snprintf (config.fwname,sizeof (config.fwname), +"qca/msnv%02x.bin" , rom_ver);else snprintf (config.fwname,sizeof (config.fwname),"qca/nvm_%08x.bin" , soc_ver); - err =qca_download_firmware (hdev, &config, soc_type); + err =qca_download_firmware (hdev, &config, soc_type, rom_ver);if (err <0 ) {bt_dev_err (hdev,"QCA Failed to download NVM (%d)" , err);return err;@@ -564,13 +603,14 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,return err; } -/* WCN399x supports the Microsoft vendor extension with 0xFD70 as the +/* WCN399x and WCN6750 supports the Microsoft vendor extension with 0xFD70 as the * VsMsftOpCode. */ switch (soc_type) {case QCA_WCN3990 :case QCA_WCN3991 :case QCA_WCN3998 : +case QCA_WCN6750 :hci_set_msft_opcode (hdev,0xFD70 );break ;default :drivers/bluetooth/btqca.h +3
-1@@ -80,7 +80,8 @@ enum qca_tlv_dnld_mode {enum qca_tlv_type {TLV_TYPE_PATCH =1 , -TLV_TYPE_NVM +TLV_TYPE_NVM , +ELF_TYPE_PATCH };struct qca_fw_config {@@ -143,6 +144,7 @@ enum qca_btsoc_type {QCA_WCN3998 ,QCA_WCN3991 ,QCA_QCA6390 , + QCA_WCN6750 };#if IS_ENABLED (CONFIG_BT_QCA )
drivers/bluetooth/btqca.h static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type) · line 170
Quoted 9 lines
drivers/bluetooth/btqca.h +6
-0@@ -160,6 +162,12 @@ static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)return soc_type ==QCA_WCN3990 || soc_type ==QCA_WCN3991 || soc_type ==QCA_WCN3998 ; } +static inline bool qca_is_wcn399x_wcn6750 (enum qca_btsoc_type soc_type) +{ +return soc_type ==QCA_WCN3990 || soc_type ==QCA_WCN3991 || + soc_type ==QCA_WCN3998 || soc_type ==QCA_WCN6750 ; +} +
I anticipate that this would eventually need to be extended to 'qca_is_wcn399x_wcn6750_wcn1234', 'qca_is_wcn399x_wcn6750_wcn1234_wcn9876', which isn't really practical. It might be better to just have 'qca_is_wcn399x()' and 'qca_is_wcn6750()' (or qca_is_wcn675x() if applicable)
IMO
if (qca_is_wcn399x(type) || qca_is_wcn6750(type))
isn't really worse than
if (qca_is_wcn399x_wcn6750(type))
personally I find the formwer even easier to read.
Quoted 20 lines
drivers/bluetooth/btqca.h +5
-0#else static inline int qca_set_bdaddr_rome (struct hci_dev *hdev,const bdaddr_t *bdaddr)@@ -192,6 +200,11 @@ static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)return false; } +static inline bool qca_is_wcn399x_wcn6750 (enum qca_btsoc_type soc_type) +{ +return false; +} +static inline int qca_send_pre_shutdown_cmd (struct hci_dev *hdev) {return -EOPNOTSUPP ;drivers/bluetooth/hci_qca.c +0
-0
drivers/bluetooth/hci_qca.c line 75
Quoted 6 lines
drivers/bluetooth/hci_qca.c +3
-0@@ -70,6 +70,10 @@#define QCA_CRASHBYTE_PACKET_LEN 1096#define QCA_MEMDUMP_BYTE 0xFB +/* BT_EN GPIO enable/disable */ +#define BT_ON 1 +#define BT_OFF 0
These aren't really needed, passing 0 and 1 to gpio_set_value() is clear enough.
Quoted 72 lines
drivers/bluetooth/hci_qca.c +10
-6+enum qca_flags {QCA_IBS_DISABLED ,QCA_DROP_VENDOR_EVENT ,@@ -218,6 +222,7 @@ struct qca_power {struct qca_serdev {struct hci_uart serdev_hu;struct gpio_desc *bt_en; +struct gpio_desc *sw_ctrl;struct clk *susclk;enum qca_btsoc_type btsoc_type;struct qca_power *bt_power;@@ -604,7 +609,7 @@ static int qca_open(struct hci_uart *hu)if (hu->serdev) { qcadev =serdev_device_get_drvdata (hu->serdev); -if (qca_is_wcn399x (qcadev->btsoc_type)) +if (qca_is_wcn399x_wcn6750 (qcadev->btsoc_type)) hu->init_speed = qcadev->init_speed;if (qcadev->oper_speed)@@ -1308,7 +1313,7 @@ static int qca_set_baudrate(struct hci_dev *hdev, uint8_t baudrate) msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS));/* Give the controller time to process the request */ -if (qca_is_wcn399x (qca_soc_type (hu))) +if (qca_is_wcn399x_wcn6750 (qca_soc_type (hu)))usleep_range (1000 ,10000 );else msleep (300 );@@ -1384,7 +1389,7 @@ static unsigned int qca_get_speed(struct hci_uart *hu,static int qca_check_speeds (struct hci_uart *hu) { -if (qca_is_wcn399x (qca_soc_type (hu))) { +if (qca_is_wcn399x_wcn6750 (qca_soc_type (hu))) {if (!qca_get_speed (hu,QCA_INIT_SPEED ) && !qca_get_speed (hu,QCA_OPER_SPEED ))return -EINVAL ;@@ -1417,7 +1422,7 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)/* Disable flow control for wcn3990 to deassert RTS while * changing the baudrate of chip and host. */ -if (qca_is_wcn399x (soc_type)) +if (qca_is_wcn399x_wcn6750 (soc_type))hci_uart_set_flow_control (hu, true);if (soc_type ==QCA_WCN3990 ) {@@ -1434,7 +1439,7 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)host_set_baudrate (hu, speed); error: -if (qca_is_wcn399x (soc_type)) +if (qca_is_wcn399x_wcn6750 (soc_type))hci_uart_set_flow_control (hu, false);if (soc_type ==QCA_WCN3990 ) {@@ -1585,10 +1590,12 @@ static bool qca_prevent_wake(struct hci_dev *hdev)return !wakeup; } -static int qca_wcn3990_init (struct hci_uart *hu) +static int qca_regulator_init (struct hci_uart *hu) { +enum qca_btsoc_type soc_type =qca_soc_type (hu);struct qca_serdev *qcadev;int ret; +bool sw_ctrl_state;/* Check for vregs status, may be hci down has turned * off the voltage regulator.
drivers/bluetooth/hci_qca.c static int qca_wcn3990_init(struct hci_uart *hu) · line 1618
Quoted 10 lines
drivers/bluetooth/hci_qca.c +2
-5@@ -1607,16 +1614,31 @@ static int qca_wcn3990_init(struct hci_uart *hu) } } -/* Forcefully enable wcn3990 to enter in to boot mode. */ -host_set_baudrate (hu,2400 ); - ret =qca_send_power_pulse (hu, false); -if (ret) -return ret; +if (qca_is_wcn399x (soc_type)) { +/* Forcefully enable wcn3990 to enter in to boot mode. */
nit: s/wcn3990/wcn399x/ since you are already touching the code
drivers/bluetooth/hci_qca.c static int qca_wcn3990_init(struct hci_uart *hu) · line 1625
Quoted 7 lines
drivers/bluetooth/hci_qca.c +7
-0+host_set_baudrate (hu,2400 ); + ret =qca_send_power_pulse (hu, false); +if (ret) +return ret; + } + +/* For wcn6750 need to enable gpio bt_en */
Does this really only apply to the wcn6750()?
From the code it's evident that the enable pin is togged, I suggest to drop the comment.
drivers/bluetooth/hci_qca.c static int qca_wcn3990_init(struct hci_uart *hu) · line 1632
Quoted 7 lines
drivers/bluetooth/hci_qca.c +7
-0+if (qcadev->bt_en) { +gpiod_set_value_cansleep (qcadev->bt_en,BT_OFF ); +msleep (50 ); +gpiod_set_value_cansleep (qcadev->bt_en,BT_ON ); +msleep (50 ); + sw_ctrl_state =gpiod_get_value_cansleep (qcadev->sw_ctrl); +bt_dev_dbg (hu->hdev,"SW_CTRL is %d" , sw_ctrl_state);
Need to check if 'sw_ctrl' is a valid GPIO?
What exactly is the role of 'SW_CTRL'?
Quoted 155 lines
drivers/bluetooth/hci_qca.c +54
-12+ }qca_set_speed (hu,QCA_INIT_SPEED ); - ret =qca_send_power_pulse (hu, true); -if (ret) -return ret; + +if (qca_is_wcn399x (soc_type)) { + ret =qca_send_power_pulse (hu, true); +if (ret) +return ret; + }/* Now the device is in ready state to communicate with host. * To sync host with device we need to reopen port. @@ -1649,12 +1671,12 @@ static int qca_power_on(struct hci_dev *hdev)if (!hu->serdev)return 0 ; -if (qca_is_wcn399x (soc_type)) { - ret =qca_wcn3990_init (hu); +if (qca_is_wcn399x_wcn6750 (soc_type)) { + ret =qca_regulator_init (hu); }else { qcadev =serdev_device_get_drvdata (hu->serdev);if (qcadev->bt_en) { -gpiod_set_value_cansleep (qcadev->bt_en,1 ); +gpiod_set_value_cansleep (qcadev->bt_en,BT_ON );/* Controller needs time to bootup. */ msleep (150 ); }@@ -1689,7 +1711,8 @@ static int qca_setup(struct hci_uart *hu)set_bit (HCI_QUIRK_SIMULTANEOUS_DISCOVERY , &hdev->quirks);bt_dev_info (hdev,"setting up %s" , -qca_is_wcn399x (soc_type) ?"wcn399x" :"ROME/QCA6390" ); +qca_is_wcn399x (soc_type) ?"wcn399x" : + (soc_type ==QCA_WCN6750 ) ?"wcn6750" :"ROME/QCA6390" ); qca->memdump_state =QCA_MEMDUMP_IDLE ;@@ -1700,7 +1723,7 @@ static int qca_setup(struct hci_uart *hu)clear_bit (QCA_SSR_TRIGGERED , &qca->flags); -if (qca_is_wcn399x (soc_type)) { +if (qca_is_wcn399x_wcn6750 (soc_type)) {set_bit (HCI_QUIRK_USE_BDADDR_PROPERTY , &hdev->quirks); ret =qca_read_soc_version (hdev, &ver, soc_type);@@ -1720,7 +1743,7 @@ static int qca_setup(struct hci_uart *hu) qca_baudrate =qca_get_baudrate_value (speed); } -if (!qca_is_wcn399x (soc_type)) { +if (!qca_is_wcn399x_wcn6750 (soc_type)) {/* Get QCA version information */ ret =qca_read_soc_version (hdev, &ver, soc_type);if (ret)@@ -1828,12 +1851,30 @@ static const struct qca_device_data qca_soc_data_qca6390 = { .num_vregs = 0, }; +static const struct qca_device_data qca_soc_data_wcn6750 = { + .soc_type =QCA_WCN6750 , + .vregs = (struct qca_vreg []) { + {"vddio" ,5000 }, + {"vddaon" ,26000 }, + {"vddbtcxmx" ,126000 }, + {"vddrfacmn" ,12500 }, + {"vddrfa0p8" ,102000 }, + {"vddrfa1p7" ,302000 }, + {"vddrfa1p2" ,257000 }, + {"vddrfa2p2" ,1700000 }, + {"vddasd" ,200 }, + }, + .num_vregs =9 , + .capabilities =QCA_CAP_WIDEBAND_SPEECH |QCA_CAP_VALID_LE_STATES , +}; +static void qca_power_shutdown (struct hci_uart *hu) {struct qca_serdev *qcadev;struct qca_data *qca = hu->priv;unsigned long flags;enum qca_btsoc_type soc_type =qca_soc_type (hu); +bool sw_ctrl_state; qcadev =serdev_device_get_drvdata (hu->serdev);@@ -1856,8 +1897,14 @@ static void qca_power_shutdown(struct hci_uart *hu)host_set_baudrate (hu,2400 );qca_send_power_pulse (hu, false);qca_regulator_disable (qcadev); + }else if (soc_type ==QCA_WCN6750 ) { +gpiod_set_value_cansleep (qcadev->bt_en,BT_OFF ); +msleep (100 ); +qca_regulator_disable (qcadev); + sw_ctrl_state =gpiod_get_value_cansleep (qcadev->sw_ctrl); +bt_dev_dbg (hu->hdev,"SW_CTRL is %d" , sw_ctrl_state); }else if (qcadev->bt_en) { -gpiod_set_value_cansleep (qcadev->bt_en,0 ); +gpiod_set_value_cansleep (qcadev->bt_en,BT_OFF ); }set_bit (QCA_BT_OFF , &qca->flags);@@ -1978,7 +2025,7 @@ static int qca_serdev_probe(struct serdev_device *serdev)if (!qcadev->oper_speed)BT_DBG ("UART will pick default operating speed" ); -if (data &&qca_is_wcn399x (data->soc_type)) { +if (data &&qca_is_wcn399x_wcn6750 (data->soc_type)) { qcadev->btsoc_type = data->soc_type; qcadev->bt_power = devm_kzalloc(&serdev->dev, sizeof(struct qca_power),@@ -1996,6 +2043,18 @@ static int qca_serdev_probe(struct serdev_device *serdev) qcadev->bt_power->vregs_on = false; + qcadev->bt_en =devm_gpiod_get_optional (&serdev->dev,"enable" , +GPIOD_OUT_LOW ); +if (!qcadev->bt_en && data->soc_type ==QCA_WCN6750 ) { +dev_err (&serdev->dev,"failed to acquire BT_EN gpio\n" ); + power_ctrl_enabled = false; + } + + qcadev->sw_ctrl =devm_gpiod_get_optional (&serdev->dev,"swctrl" , +GPIOD_IN ); +if (!qcadev->sw_ctrl && data->soc_type ==QCA_WCN6750 ) +dev_warn (&serdev->dev,"failed to acquire SW_CTRL gpio\n" ); + qcadev->susclk =devm_clk_get_optional (&serdev->dev,NULL );if (IS_ERR (qcadev->susclk)) {dev_err (&serdev->dev,"failed to acquire clk\n" );@@ -2068,7 +2127,7 @@ static void qca_serdev_remove(struct serdev_device *serdev)struct qca_serdev *qcadev =serdev_device_get_drvdata (serdev);struct qca_power *power = qcadev->bt_power; -if (qca_is_wcn399x (qcadev->btsoc_type) && power->vregs_on) +if (qca_is_wcn399x_wcn6750 (qcadev->btsoc_type) && power->vregs_on)qca_power_shutdown (&qcadev->serdev_hu);else if (qcadev->susclk)clk_disable_unprepare (qcadev->susclk);@@ -2244,6 +2303,7 @@ static const struct of_device_id qca_bluetooth_of_match[] = { { .compatible = "qcom,wcn3990-bt", .data = &qca_soc_data_wcn3990}, { .compatible = "qcom,wcn3991-bt", .data = &qca_soc_data_wcn3991}, { .compatible = "qcom,wcn3998-bt", .data = &qca_soc_data_wcn3998}, + { .compatible = "qcom,wcn6750-bt", .data = &qca_soc_data_wcn6750}, {/* sentinel */ } };MODULE_DEVICE_TABLE (of, qca_bluetooth_of_match);Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
Re: [PATCH v2 1/3] Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750
Hi Matthias,
Quoted 86 lines · Matthias Kaehlcke
Quoted 85 lines · Venkata Lakshmi Narayana Gubba
Added regulators,GPIOs and changes required to power on/off wcn6750. Added support for firmware download for wcn6750.
Changes done in detail:
1. Added regulators and corresponding current values.
2. Addedsw_ctrlGPIO pin which is output from BT SoC and indicates status of clock supply to BT SoC.
3. Added inline function to check if the SoC type is wcn399x or wcn6750.
4. Modified the functionqca_wcn3990_init()to support wcn6750 and renamed it toqca_regulator_init().
5. AddedBT_ONandBT_OFFmacros.
6. Added support to download mbn type firmware image as wcn6750 supports mbn type image.
7. If mbn type image is not present then we will check for tlv type image.
8. Moved extracting rom version info to common place as this code is common in all if else ladder inqca_uart_setup.Signed-off-by Venkata Lakshmi Narayana Gubba <[email protected]>--- drivers/bluetooth/btqca.c | 88 ++++++++++++++++++++++++++---------- drivers/bluetooth/btqca.h | 15 ++++++- drivers/bluetooth/hci_qca.c | 106 ++++++++++++++++++++++++++++++++++---------- 3 files changed, 161 insertions(+), 48 deletions(-)drivers/bluetooth/btqca.c +2
-1@@ -182,7 +182,8 @@ int qca_send_pre_shutdown_cmd(struct hci_dev *hdev) }EXPORT_SYMBOL_GPL (qca_send_pre_shutdown_cmd); -static void qca_tlv_check_data (struct qca_fw_config *config, +static void qca_tlv_check_data (struct hci_dev *hdev, +struct qca_fw_config *config,const struct firmware *fw,enum qca_btsoc_type soc_type) {drivers/bluetooth/btqca.c +10
-8const u8 *data;@@ -194,19 +195,21 @@ static void qca_tlv_check_data(structqca_fw_config *config, struct tlv_type_nvm *tlv_nvm;uint8_t nvm_baud_rate = config->user_baud_rate; - tlv = (struct tlv_type_hdr *)fw->data; - - type_len =le32_to_cpu (tlv->type_len); - length = (type_len >>8 ) &0x00ffffff ; - -BT_DBG ("TLV Type\t\t : 0x%x" , type_len &0x000000ff ); -BT_DBG ("Length\t\t : %d bytes" , length); - config->dnld_mode =QCA_SKIP_EVT_NONE ; config->dnld_type =QCA_SKIP_EVT_NONE ;switch (config->type) { +case ELF_TYPE_PATCH : + config->dnld_mode =QCA_SKIP_EVT_VSE_CC ; + config->dnld_type =QCA_SKIP_EVT_VSE_CC ; + +bt_dev_dbg (hdev,"File Class : 0x%x" , fw->data[4 ]); +bt_dev_dbg (hdev,"Data Encoding : 0x%x" , fw->data[5 ]); +bt_dev_dbg (hdev,"File version : 0x%x" , fw->data[6 ]); +break ;case TLV_TYPE_PATCH : + tlv = (struct tlv_type_hdr *)fw->data; + type_len =le32_to_cpu (tlv->type_len); tlv_patch = (struct tlv_type_patch *)tlv->data;drivers/bluetooth/btqca.c +1
-0/* For Rome version 1.1 to 3.1, all segment commands @@ -218,6 +221,7 @@ static void qca_tlv_check_data(struct qca_fw_config *config, config->dnld_mode = tlv_patch->download_mode; config->dnld_type = config->dnld_mode; +BT_DBG ("TLV Type\t\t : 0x%x" , type_len &0x000000ff );BT_DBG ("Total Length : %d bytes" ,le32_to_cpu (tlv_patch->total_size));drivers/bluetooth/btqca.c +0
-0BT_DBG("Patch Data Length : %d bytes",@@ -243,6 +247,14 @@ static void qca_tlv_check_data(structqca_fw_config *config, break;
Quoted 13 lines
drivers/bluetooth/btqca.c static void qca_tlv_check_data(struct qca_fw_config *config, · line 257
Quoted 9 lines
drivers/bluetooth/btqca.c +8
-0case TLV_TYPE_NVM : + tlv = (struct tlv_type_hdr *)fw->data; + + type_len =le32_to_cpu (tlv->type_len); + length = (type_len >>8 ) &0x00ffffff ; + +BT_DBG ("TLV Type\t\t : 0x%x" , type_len &0x000000ff ); +BT_DBG ("Length\t\t : %d bytes" , length); +To keep the wcn6750 shorther you could consider to have a separate patch for the ELF type and the additional logging.
[Venkata]:
Sure, I will send as a seperate patch in next patchset.
Quoted 54 lines
Quoted 54 lines
drivers/bluetooth/btqca.c +0
-0idx =0 ; data = tlv->data;drivers/bluetooth/btqca.c +2
-1while (idx < length) {@@ -387,7 +399,8 @@ static int qca_inject_cmd_complete_event(struct hci_dev *hdev)static int qca_download_firmware (struct hci_dev *hdev,struct qca_fw_config *config, -enum qca_btsoc_type soc_type) +enum qca_btsoc_type soc_type, +u8 rom_ver) {const struct firmware *fw;drivers/bluetooth/btqca.c +21
-4const u8 *segment;@@ -397,12 +410,29 @@ static int qca_download_firmware(struct hci_dev *hdev, ret =request_firmware (&fw, config->fwname, &hdev->dev);if (ret) { -bt_dev_err (hdev,"QCA Failed to request file: %s (%d)" , - config->fwname, ret); -return ret; +/* For WCN6750, if mbn file is not present then check for +* tlv file. +*/ +if (soc_type ==QCA_WCN6750 && config->type ==ELF_TYPE_PATCH ) { +bt_dev_dbg (hdev,"QCA Failed to request file: %s (%d)" , + config->fwname, ret); + config->type =TLV_TYPE_PATCH ; +snprintf (config->fwname,sizeof (config->fwname), +"qca/msbtfw%02x.tlv" , rom_ver); + ret =request_firmware (&fw, config->fwname, &hdev->dev); +if (ret) { +bt_dev_err (hdev,"QCA Failed to request file: %s (%d)" , + config->fwname, ret); +return ret; + } + }else { +bt_dev_err (hdev,"QCA Failed to request file: %s (%d)" , + config->fwname, ret); +return ret; + } } -qca_tlv_check_data (config, fw, soc_type); +qca_tlv_check_data (hdev, config, fw, soc_type); segment = fw->data;drivers/bluetooth/btqca.c +0
-0remain = fw->size;@@ -502,27 +532,33 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate, config.user_baud_rate = baudrate;
Quoted 9 lines
drivers/bluetooth/btqca.c int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate, · line 540
Quoted 6 lines
drivers/bluetooth/btqca.c +6
-0+/* Firmware files to download are based on ROM version. +* ROM version is derived from last two bytes of soc_ver. +*/ + rom_ver = ((soc_ver &0x00000f00 ) >>0x04 ) | + (soc_ver &0x0000000f ); +This refactoring could also be done in a separate patch.
[Venkata]:
Sure.I will send as a seperate patch in next patchset.
Quoted 110 lines
Quoted 92 lines
drivers/bluetooth/btqca.c +8
-8/* Download rampatch file */ config.type =TLV_TYPE_PATCH ;if (qca_is_wcn399x (soc_type)) { -/* Firmware files to download are based on ROM version. -* ROM version is derived from last two bytes of soc_ver. -*/ - rom_ver = ((soc_ver &0x00000f00 ) >>0x04 ) | - (soc_ver &0x0000000f );snprintf (config.fwname,sizeof (config.fwname),"qca/crbtfw%02x.tlv" , rom_ver); }else if (soc_type ==QCA_QCA6390 ) { - rom_ver = ((soc_ver &0x00000f00 ) >>0x04 ) | - (soc_ver &0x0000000f );snprintf (config.fwname,sizeof (config.fwname),"qca/htbtfw%02x.tlv" , rom_ver); + }else if (soc_type ==QCA_WCN6750 ) { +/* Choose mbn file by default.If mbn file is not found +* then choose tlv file +*/ + config.type =ELF_TYPE_PATCH ; +snprintf (config.fwname,sizeof (config.fwname), +"qca/msbtfw%02x.mbn" , rom_ver); }else {snprintf (config.fwname,sizeof (config.fwname),"qca/rampatch_%08x.bin" , soc_ver); } - err =qca_download_firmware (hdev, &config, soc_type); + err =qca_download_firmware (hdev, &config, soc_type, rom_ver);if (err <0 ) {bt_dev_err (hdev,"QCA Failed to download patch (%d)" , err);drivers/bluetooth/btqca.c +4
-1return err;@@ -548,11 +584,14 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate, else if (soc_type == QCA_QCA6390)snprintf (config.fwname,sizeof (config.fwname),"qca/htnv%02x.bin" , rom_ver); +else if (soc_type ==QCA_WCN6750 ) +snprintf (config.fwname,sizeof (config.fwname), +"qca/msnv%02x.bin" , rom_ver);else snprintf (config.fwname,sizeof (config.fwname),"qca/nvm_%08x.bin" , soc_ver); - err =qca_download_firmware (hdev, &config, soc_type); + err =qca_download_firmware (hdev, &config, soc_type, rom_ver);if (err <0 ) {bt_dev_err (hdev,"QCA Failed to download NVM (%d)" , err);drivers/bluetooth/btqca.c +0
-1return err;@@ -564,13 +603,14 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate, return err; } -/* WCN399x supports the Microsoft vendor extension with 0xFD70 as the
drivers/bluetooth/btqca.c +1
-0+/* WCN399x and WCN6750 supports the Microsoft vendor extension with
0xFD70as thedrivers/bluetooth/btqca.c +1
-0* VsMsftOpCode. */ switch (soc_type) {case QCA_WCN3990 :case QCA_WCN3991 :case QCA_WCN3998 : +case QCA_WCN6750 :hci_set_msft_opcode (hdev,0xFD70 );break ;default :drivers/bluetooth/btqca.h +3
-1@@ -80,7 +80,8 @@ enum qca_tlv_dnld_mode {enum qca_tlv_type {TLV_TYPE_PATCH =1 , -TLV_TYPE_NVM +TLV_TYPE_NVM , +ELF_TYPE_PATCH };struct qca_fw_config {@@ -143,6 +144,7 @@ enum qca_btsoc_type {QCA_WCN3998 ,QCA_WCN3991 ,QCA_QCA6390 , + QCA_WCN6750 };#if IS_ENABLED (CONFIG_BT_QCA )@@ -160,6 +162,12 @@ static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)drivers/bluetooth/btqca.h static inline bool qca_is_wcn399x(enum · line 172
Quoted 10 lines
drivers/bluetooth/btqca.h +6
-0return soc_type ==QCA_WCN3990 || soc_type ==QCA_WCN3991 || soc_type ==QCA_WCN3998 ; } +static inline bool qca_is_wcn399x_wcn6750 (enum qca_btsoc_type soc_type) +{ +return soc_type ==QCA_WCN3990 || soc_type ==QCA_WCN3991 || + soc_type ==QCA_WCN3998 || soc_type ==QCA_WCN6750 ; +} +I anticipate that this would eventually need to be extended to '
qca_is_wcn399x_wcn6750_wcn1234', 'qca_is_wcn399x_wcn6750_wcn1234_wcn9876', which isn't really practical. It might be better to just have 'qca_is_wcn399x()' and 'qca_is_wcn6750()' (orqca_is_wcn675x()if applicable)IMO
Quoted 9 lines
if (qca_is_wcn399x(type) || qca_is_wcn6750(type))isn't really worse than
if (
qca_is_wcn399x_wcn6750(type))personally I find the formwer even easier to read.
[Venkata]:
Sure.I will update in next patchset.
Quoted 26 lines
Quoted 26 lines
drivers/bluetooth/btqca.h +0
-0#else static inline int qca_set_bdaddr_rome(struct
hci_dev*hdev, constbdaddr_t*bdaddr)drivers/bluetooth/btqca.h +5
-0@@ -192,6 +200,11 @@ static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)return false; } +static inline bool qca_is_wcn399x_wcn6750 (enum qca_btsoc_type soc_type) +{ +return false; +} +static inline int qca_send_pre_shutdown_cmd (struct hci_dev *hdev){
drivers/bluetooth/btqca.h +0
-0return -EOPNOTSUPP ;drivers/bluetooth/hci_qca.c +0
-0@@ -70,6 +70,10 @@#define QCA_CRASHBYTE_PACKET_LEN 1096#define QCA_MEMDUMP_BYTE 0xFB
Quoted 6 lines
drivers/bluetooth/hci_qca.c line 75
Quoted 3 lines
drivers/bluetooth/hci_qca.c +3
-0+/* BT_EN GPIO enable/disable */ +#define BT_ON 1 +#define BT_OFF 0These aren't really needed, passing 0 and 1 to
gpio_set_value()is clear enough.
[Venkata]:
I will update in next patch set.
Quoted 81 lines
Quoted 81 lines
drivers/bluetooth/hci_qca.c +4
-2+enum qca_flags {QCA_IBS_DISABLED ,QCA_DROP_VENDOR_EVENT ,@@ -218,6 +222,7 @@ struct qca_power {struct qca_serdev {struct hci_uart serdev_hu;struct gpio_desc *bt_en; +struct gpio_desc *sw_ctrl;struct clk *susclk;enum qca_btsoc_type btsoc_type;struct qca_power *bt_power;@@ -604,7 +609,7 @@ static int qca_open(struct hci_uart *hu)if (hu->serdev) { qcadev =serdev_device_get_drvdata (hu->serdev); -if (qca_is_wcn399x (qcadev->btsoc_type)) +if (qca_is_wcn399x_wcn6750 (qcadev->btsoc_type)) hu->init_speed = qcadev->init_speed;if (qcadev->oper_speed)@@ -1308,7 +1313,7 @@ static int qca_set_baudrate(struct hci_dev *hdev, uint8_t baudrate) msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS));/* Give the controller time to process the request */ -if (qca_is_wcn399x (qca_soc_type (hu))) +if (qca_is_wcn399x_wcn6750 (qca_soc_type (hu)))usleep_range (1000 ,10000 );else drivers/bluetooth/hci_qca.c +1
-1msleep (300 );@@ -1384,7 +1389,7 @@ static unsigned int qca_get_speed(structhci_uart *hu, static int qca_check_speeds(struct hci_uart *hu) { - if (qca_is_wcn399x(qca_soc_type(hu))) { + if (qca_is_wcn399x_wcn6750(qca_soc_type(hu))) { if (!qca_get_speed(hu, QCA_INIT_SPEED) && !qca_get_speed(hu, QCA_OPER_SPEED))drivers/bluetooth/hci_qca.c +1
-1return -EINVAL ;@@ -1417,7 +1422,7 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)/* Disable flow control for wcn3990 to deassert RTS while * changing the baudrate of chip and host. */ -if (qca_is_wcn399x (soc_type)) +if (qca_is_wcn399x_wcn6750 (soc_type))hci_uart_set_flow_control (hu, true);drivers/bluetooth/hci_qca.c +1
-1if (soc_type ==QCA_WCN3990 ) {@@ -1434,7 +1439,7 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)host_set_baudrate (hu ,speed ); error: -if (qca_is_wcn399x (soc_type)) +if (qca_is_wcn399x_wcn6750 (soc_type))hci_uart_set_flow_control (hu, false);drivers/bluetooth/hci_qca.c +3
-1if (soc_type ==QCA_WCN3990 ) {@@ -1585,10 +1590,12 @@ static bool qca_prevent_wake(struct hci_dev *hdev)return !wakeup; } -static int qca_wcn3990_init (struct hci_uart *hu) +static int qca_regulator_init (struct hci_uart *hu) { +enum qca_btsoc_type soc_type =qca_soc_type (hu);struct qca_serdev *qcadev;int ret; +bool sw_ctrl_state;/* Check for vregs status, may be hci down has turned drivers/bluetooth/hci_qca.c +0
-0* off the voltage regulator. @@ -1607,16 +1614,31 @@ static int qca_wcn3990_init(struct hci_uart *hu) } }
Quoted 10 lines
drivers/bluetooth/hci_qca.c static int qca_wcn3990_init(struct hci_uart *hu) · line 1618
Quoted 7 lines
drivers/bluetooth/hci_qca.c +2
-5-/* Forcefully enable wcn3990 to enter in to boot mode. */ -host_set_baudrate (hu,2400 ); - ret =qca_send_power_pulse (hu, false); -if (ret) -return ret; +if (qca_is_wcn399x (soc_type)) { +/* Forcefully enable wcn3990 to enter in to boot mode. */ nit: s/wcn3990/wcn399x/ since you are already touching the code
[Venkata]:
I will update in next patchset.
Quoted 10 lines
drivers/bluetooth/hci_qca.c static int qca_wcn3990_init(struct hci_uart *hu) · line 1625
Quoted 7 lines
drivers/bluetooth/hci_qca.c +7
-0+host_set_baudrate (hu,2400 ); + ret =qca_send_power_pulse (hu, false); +if (ret) +return ret; + } + +/* For wcn6750 need to enable gpio bt_en */ Does this really only apply to the
wcn6750()?
Quoted 3 lines
From the code it's evident that the enable pin is togged, I suggest to drop the comment.
[Venkata] :
Yes, Below code only apply to WCN6750.
Quoted 10 lines
drivers/bluetooth/hci_qca.c static int qca_wcn3990_init(struct hci_uart *hu) · line 1632
Quoted 7 lines
drivers/bluetooth/hci_qca.c +7
-0+if (qcadev->bt_en) { +gpiod_set_value_cansleep (qcadev->bt_en,BT_OFF ); +msleep (50 ); +gpiod_set_value_cansleep (qcadev->bt_en,BT_ON ); +msleep (50 ); + sw_ctrl_state =gpiod_get_value_cansleep (qcadev->sw_ctrl); +bt_dev_dbg (hu->hdev,"SW_CTRL is %d" , sw_ctrl_state);Need to check if '
sw_ctrl' is a valid GPIO?
Quoted 2 lines
What exactly is the role of '
SW_CTRL'?
[Venkata]:
I will add check if sw_ctrl is a valid GPIO.sw_ctrl is output from BT SoC to Host.It indicates status of clock supply to SoC.
Quoted 153 lines
Quoted 153 lines
drivers/bluetooth/hci_qca.c +7
-3+ }qca_set_speed (hu,QCA_INIT_SPEED ); - ret =qca_send_power_pulse (hu, true); -if (ret) -return ret; + +if (qca_is_wcn399x (soc_type)) { + ret =qca_send_power_pulse (hu, true); +if (ret) +return ret; + }/* Now the device is in ready state to communicate with host. drivers/bluetooth/hci_qca.c +32
-7* To sync host with device we need to reopen port. @@ -1649,12 +1671,12 @@ static int qca_power_on(struct hci_dev *hdev)if (!hu->serdev)return 0 ; -if (qca_is_wcn399x (soc_type)) { - ret =qca_wcn3990_init (hu); +if (qca_is_wcn399x_wcn6750 (soc_type)) { + ret =qca_regulator_init (hu); }else { qcadev =serdev_device_get_drvdata (hu->serdev);if (qcadev->bt_en) { -gpiod_set_value_cansleep (qcadev->bt_en,1 ); +gpiod_set_value_cansleep (qcadev->bt_en,BT_ON );/* Controller needs time to bootup. */ msleep (150 ); }@@ -1689,7 +1711,8 @@ static int qca_setup(struct hci_uart *hu)set_bit (HCI_QUIRK_SIMULTANEOUS_DISCOVERY , &hdev->quirks);bt_dev_info (hdev,"setting up %s" , -qca_is_wcn399x (soc_type) ?"wcn399x" :"ROME/QCA6390" ); +qca_is_wcn399x (soc_type) ?"wcn399x" : + (soc_type ==QCA_WCN6750 ) ?"wcn6750" :"ROME/QCA6390" ); qca->memdump_state =QCA_MEMDUMP_IDLE ;@@ -1700,7 +1723,7 @@ static int qca_setup(struct hci_uart *hu)clear_bit (QCA_SSR_TRIGGERED , &qca->flags); -if (qca_is_wcn399x (soc_type)) { +if (qca_is_wcn399x_wcn6750 (soc_type)) {set_bit (HCI_QUIRK_USE_BDADDR_PROPERTY , &hdev->quirks); ret =qca_read_soc_version (hdev, &ver, soc_type);@@ -1720,7 +1743,7 @@ static int qca_setup(struct hci_uart *hu) qca_baudrate =qca_get_baudrate_value (speed); } -if (!qca_is_wcn399x (soc_type)) { +if (!qca_is_wcn399x_wcn6750 (soc_type)) {/* Get QCA version information */ ret =qca_read_soc_version (hdev, &ver, soc_type);if (ret)@@ -1828,12 +1851,30 @@ static const struct qca_device_data qca_soc_data_qca6390 = { .num_vregs = 0, }; +static const struct qca_device_data qca_soc_data_wcn6750 = { + .soc_type =QCA_WCN6750 , + .vregs = (struct qca_vreg []) { + {"vddio" ,5000 }, + {"vddaon" ,26000 }, + {"vddbtcxmx" ,126000 }, + {"vddrfacmn" ,12500 }, + {"vddrfa0p8" ,102000 }, + {"vddrfa1p7" ,302000 }, + {"vddrfa1p2" ,257000 }, + {"vddrfa2p2" ,1700000 }, + {"vddasd" ,200 }, + }, + .num_vregs =9 , + .capabilities =QCA_CAP_WIDEBAND_SPEECH |QCA_CAP_VALID_LE_STATES , +}; +static void qca_power_shutdown (struct hci_uart *hu) {struct qca_serdev *qcadev;struct qca_data *qca = hu->priv;unsigned long flags;enum qca_btsoc_type soc_type =qca_soc_type (hu); +bool sw_ctrl_state; qcadev =serdev_device_get_drvdata (hu->serdev);@@ -1856,8 +1897,14 @@ static void qca_power_shutdown(struct hci_uart *hu)host_set_baudrate (hu,2400 );qca_send_power_pulse (hu, false);qca_regulator_disable (qcadev); + }else if (soc_type ==QCA_WCN6750 ) { +gpiod_set_value_cansleep (qcadev->bt_en,BT_OFF ); +msleep (100 ); +qca_regulator_disable (qcadev); + sw_ctrl_state =gpiod_get_value_cansleep (qcadev->sw_ctrl); +bt_dev_dbg (hu->hdev,"SW_CTRL is %d" , sw_ctrl_state); }else if (qcadev->bt_en) { -gpiod_set_value_cansleep (qcadev->bt_en,0 ); +gpiod_set_value_cansleep (qcadev->bt_en,BT_OFF ); }drivers/bluetooth/hci_qca.c +1
-1set_bit (QCA_BT_OFF , &qca->flags);@@ -1978,7 +2025,7 @@ static int qca_serdev_probe(struct serdev_device *serdev)if (!qcadev->oper_speed)BT_DBG ("UART will pick default operating speed" ); -if (data &&qca_is_wcn399x (data->soc_type)) { +if (data &&qca_is_wcn399x_wcn6750 (data->soc_type)) { qcadev->btsoc_type = data->soc_type; qcadev->bt_power = devm_kzalloc(&serdev->dev,drivers/bluetooth/hci_qca.c +12
-0sizeof(struct qca_power),@@ -1996,6 +2043,18 @@ static int qca_serdev_probe(struct serdev_device *serdev) qcadev->bt_power->vregs_on = false; + qcadev->bt_en =devm_gpiod_get_optional (&serdev->dev,"enable" , +GPIOD_OUT_LOW ); +if (!qcadev->bt_en && data->soc_type ==QCA_WCN6750 ) { +dev_err (&serdev->dev,"failed to acquire BT_EN gpio\n" ); + power_ctrl_enabled = false; + } + + qcadev->sw_ctrl =devm_gpiod_get_optional (&serdev->dev,"swctrl" , +GPIOD_IN ); +if (!qcadev->sw_ctrl && data->soc_type ==QCA_WCN6750 ) +dev_warn (&serdev->dev,"failed to acquire SW_CTRL gpio\n" ); + qcadev->susclk =devm_clk_get_optional (&serdev->dev,NULL );if (IS_ERR (qcadev->susclk)) {drivers/bluetooth/hci_qca.c +1
-1dev_err (&serdev->dev,"failed to acquire clk\n" );@@ -2068,7 +2127,7 @@ static void qca_serdev_remove(struct serdev_device *serdev)struct qca_serdev *qcadev =serdev_device_get_drvdata (serdev);struct qca_power *power = qcadev->bt_power; -if (qca_is_wcn399x (qcadev->btsoc_type) && power->vregs_on) +if (qca_is_wcn399x_wcn6750 (qcadev->btsoc_type) && power->vregs_on)qca_power_shutdown (&qcadev->serdev_hu);else if (qcadev->susclk)drivers/bluetooth/hci_qca.c +0
-0clk_disable_unprepare (qcadev->susclk);@@ -2244,6 +2303,7 @@ static const struct of_device_id qca_bluetooth_of_match[] = { { .compatible = "qcom,wcn3990-bt", .data = &qca_soc_data_wcn3990}, { .compatible = "qcom,wcn3991-bt", .data = &qca_soc_data_wcn3991}, { .compatible = "qcom,wcn3998-bt", .data = &qca_soc_data_wcn3998},
Quoted 8 lines
Quoted 8 lines
drivers/bluetooth/hci_qca.c +1
-0+ { .compatible = "qcom,wcn6750-bt", .data = &qca_soc_data_wcn6750}, {/* sentinel */ } };
MODULE_DEVICE_TABLE(of, qca_bluetooth_of_match);
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
Regards,
Venkata.
PATCH v2 2/3 dt-bindings: net: bluetooth: Convert to DT schema
In reply to Venkata Lakshmi Narayana GubbaConverted Qualcomm Bluetooth binidings to DT schema.
--- .../devicetree/bindings/net/qualcomm-bluetooth.txt | 69 ----------------- .../bindings/net/qualcomm-bluetooth.yaml | 87 ++++++++++++++++++++++ 2 files changed, 87 insertions(+), 69 deletions(-) delete mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt create mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml
Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt deleted +0 -69
@@ -1,69 +0,0 @@ -Qualcomm Bluetooth Chips ---------------------- - -This documents the binding structure and common properties for serial -attached Qualcomm devices. - -Serial attached Qualcomm devices shall be a child node of the host UART -device the slave device is attached to. - -Required properties: - - compatible: should contain one of the following: - * "qcom,qca6174-bt" - * "qcom,qca9377-bt" - * "qcom,wcn3990-bt" - * "qcom,wcn3991-bt" - * "qcom,wcn3998-bt" - * "qcom,qca6390-bt" - -Optional properties for compatible string qcom,qca6174-bt: - - - enable-gpios: gpio specifier used to enable chip - - clocks: clock provided to the controller (SUSCLK_32KHZ) - - firmware-name: specify the name of nvm firmware to load - -Optional properties for compatible string qcom,qca9377-bt: - - - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml - -Required properties for compatible string qcom,wcn399x-bt: - - - vddio-supply: VDD_IO supply regulator handle. - - vddxo-supply: VDD_XO supply regulator handle. - - vddrf-supply: VDD_RF supply regulator handle. - - vddch0-supply: VDD_CH0 supply regulator handle. - -Optional properties for compatible string qcom,wcn399x-bt: - - - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml - - firmware-name: specify the name of nvm firmware to load - - clocks: clock provided to the controller - -Examples: - -serial@7570000 { - label = "BT-UART"; - status = "okay"; - - bluetooth { - compatible = "qcom,qca6174-bt"; - - enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; - clocks = <&divclk4>; - firmware-name = "nvm_00440302.bin"; - }; -}; - -serial@898000 { - bluetooth { - compatible = "qcom,wcn3990-bt"; - - vddio-supply = <&vreg_s4a_1p8>; - vddxo-supply = <&vreg_l7a_1p8>; - vddrf-supply = <&vreg_l17a_1p3>; - vddch0-supply = <&vreg_l25a_3p3>; - max-speed = <3200000>; - firmware-name = "crnv21.bin"; - clocks = <&rpmhcc RPMH_RF_CLK2>; - }; -};
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +87 -0
87 lines not on this page · raw message
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
Re: [PATCH v2 2/3] dt-bindings: net: bluetooth: Convert to DT schema
Quoted 1 line · Venkata Lakshmi Narayana Gubba
Subject: dt-bindings: net: bluetooth: Convert to DT schema
This doesn't convert the generic binding or all bindings to DT schema as the subject suggests, but the Qualcomm BT binding.
Quoted 106 lines
Converted Qualcomm Bluetooth binidings to DT schema.
Signed-off-by Venkata Lakshmi Narayana Gubba <[email protected]>--- .../devicetree/bindings/net/qualcomm-bluetooth.txt | 69 ----------------- .../bindings/net/qualcomm-bluetooth.yaml | 87 ++++++++++++++++++++++ 2 files changed, 87 insertions(+), 69 deletions(-) delete mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt create mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.yamlDocumentation/devicetree/bindings/net/qualcomm-bluetooth.txt deleted +0
-69@@ -1,69 +0,0 @@ -Qualcomm Bluetooth Chips ---------------------- - -This documents the binding structure and common properties for serial -attached Qualcomm devices. - -Serial attached Qualcomm devices shall be a child node of the host UART -device the slave device is attached to. - -Required properties: - - compatible: should contain one of the following: - * "qcom,qca6174-bt" - * "qcom,qca9377-bt" - * "qcom,wcn3990-bt" - * "qcom,wcn3991-bt" - * "qcom,wcn3998-bt" - * "qcom,qca6390-bt" - -Optional properties for compatible string qcom,qca6174-bt: - - - enable-gpios: gpio specifier used to enable chip - - clocks: clock provided to the controller (SUSCLK_32KHZ) - - firmware-name: specify the name of nvm firmware to load - -Optional properties for compatible string qcom,qca9377-bt: - - - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml - -Required properties for compatible string qcom,wcn399x-bt: - - - vddio-supply: VDD_IO supply regulator handle. - - vddxo-supply: VDD_XO supply regulator handle. - - vddrf-supply: VDD_RF supply regulator handle. - - vddch0-supply: VDD_CH0 supply regulator handle. - -Optional properties for compatible string qcom,wcn399x-bt: - - - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml - - firmware-name: specify the name of nvm firmware to load - - clocks: clock provided to the controller - -Examples: - -serial@7570000 { - label = "BT-UART"; - status = "okay"; - - bluetooth { - compatible = "qcom,qca6174-bt"; - - enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; - clocks = <&divclk4>; - firmware-name = "nvm_00440302.bin"; - }; -}; - -serial@898000 { - bluetooth { - compatible = "qcom,wcn3990-bt"; - - vddio-supply = <&vreg_s4a_1p8>; - vddxo-supply = <&vreg_l7a_1p8>; - vddrf-supply = <&vreg_l17a_1p3>; - vddch0-supply = <&vreg_l25a_3p3>; - max-speed = <3200000>; - firmware-name = "crnv21.bin"; - clocks = <&rpmhcc RPMH_RF_CLK2>; - }; -};Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +14
-0@@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/qualcomm-bluetooth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Bluetooth Chips + +maintainers: + - Rob Herring <[email protected]> + - Marcel Holtmann <[email protected]> + +description: + This binding describes Qualcomm UART-attached bluetooth chips.
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml line 24
Quoted 10 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +10
-0+ +properties: + compatible: + enum: + - qcom,qca6174-bt + - qcom,qca9377-bt + - qcom,wcn3990-bt + - qcom,wcn3991-bt + - qcom,wcn3998-bt + - qcom,qca6390-bt
delete trailing blanks
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml line 29
Quoted 5 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +5
-0+ + enable-gpios: + maxItems: 1 + description: gpio specifier used to enable chip +
delete blanks
Quoted 7 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +7
-0+ clocks: + maxItems: 1 + description: clock provided to the controller (SUSCLK_32KHZ) + + vddio-supply: + description: VDD_IO supply regulator handle +
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml line 46
Quoted 10 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +10
-0+ vddxo-supply: + description: VDD_XO supply regulator handle + + vddrf-supply: + description: VDD_RF supply regulator handle + + vddch0-supply: + description: VDD_CH0 supply regulator handle + + max-speed:
delete trailing blank
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml line 57
Quoted 11 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +11
-0+ description: see Documentation/devicetree/bindings/serial/serial.yaml + + firmware-name: + description: specify the name of nvm firmware to load + + local-bd-address: + description: see Documentation/devicetree/bindings/net/bluetooth.txt + + +required: + - compatible
it seems you could make the supplies conditionally required based on the compatible string. See Documentation/devicetree/bindings/connector/usb-connector.yaml for an example
Quoted 18 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +18
-0+ +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + uart { + label = "BT-UART"; + status = "okay"; + + bluetooth { + compatible = "qcom,qca6174-bt"; + enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; + clocks = <&divclk4>; + firmware-name = "nvm_00440302.bin"; + }; + }; + - |
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml line 85
Quoted 10 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +10
-0+ uart { + + bluetooth { + compatible = "qcom,wcn3990-bt"; + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>; + max-speed = <3200000>; + firmware-name = "crnv21.bin";
delete trailing blanks
Re: [PATCH v2 2/3] dt-bindings: net: bluetooth: Convert to DT schema
Hi Matthias,
Quoted 7 lines · Matthias Kaehlcke
Quoted 1 line · Venkata Lakshmi Narayana Gubba
Subject: dt-bindings: net: bluetooth: Convert to DT schema
This doesn't convert the generic binding or all bindings to DT schema as the subject suggests, but the Qualcomm BT binding.
[Venkata]:
I will update in next patchset.
Quoted 117 lines
Quoted 117 lines
Converted Qualcomm Bluetooth binidings to DT schema.
Signed-off-by Venkata Lakshmi Narayana Gubba <[email protected]>--- .../devicetree/bindings/net/qualcomm-bluetooth.txt | 69 ----------------- .../bindings/net/qualcomm-bluetooth.yaml | 87 ++++++++++++++++++++++ 2 files changed, 87 insertions(+), 69 deletions(-) delete mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt create mode 100644
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yamlDocumentation/devicetree/bindings/net/qualcomm-bluetooth.txt deleted +0
-7@@ -1,69 +0,0 @@ -Qualcomm Bluetooth Chips ---------------------- - -This documents the binding structure and common properties for serial -attached Qualcomm devices. - -Serial attached Qualcomm devices shall be a child node of the hostUART
Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt deleted +0
-20-device the slave device is attached to. - -Required properties: - - compatible: should contain one of the following: - * "qcom,qca6174-bt" - * "qcom,qca9377-bt" - * "qcom,wcn3990-bt" - * "qcom,wcn3991-bt" - * "qcom,wcn3998-bt" - * "qcom,qca6390-bt" - -Optional properties for compatible string qcom,qca6174-bt: - - - enable-gpios: gpio specifier used to enable chip - - clocks: clock provided to the controller (SUSCLK_32KHZ) - - firmware-name: specify the name of nvm firmware to load - -Optional properties for compatible string qcom,qca9377-bt: - - - max-speed: see
Documentation/devicetree/bindings/serial/serial.yamlDocumentation/devicetree/bindings/net/qualcomm-bluetooth.txt deleted +0
-11- -Required properties for compatible string qcom,wcn399x-bt: - - - vddio-supply: VDD_IO supply regulator handle. - - vddxo-supply: VDD_XO supply regulator handle. - - vddrf-supply: VDD_RF supply regulator handle. - - vddch0-supply: VDD_CH0 supply regulator handle. - -Optional properties for compatible string qcom,wcn399x-bt: - - - max-speed: see
Documentation/devicetree/bindings/serial/serial.yaml
- - firmware-name: specify the name of nvm firmware to load
- - clocks: clock provided to the controllerDocumentation/devicetree/bindings/net/qualcomm-bluetooth.txt deleted +0
-29- -Examples: - -serial@7570000 { - label = "BT-UART"; - status = "okay"; - - bluetooth { - compatible = "qcom,qca6174-bt"; - - enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; - clocks = <&divclk4>; - firmware-name = "nvm_00440302.bin"; - }; -}; - -serial@898000 { - bluetooth { - compatible = "qcom,wcn3990-bt"; - - vddio-supply = <&vreg_s4a_1p8>; - vddxo-supply = <&vreg_l7a_1p8>; - vddrf-supply = <&vreg_l17a_1p3>; - vddch0-supply = <&vreg_l25a_3p3>; - max-speed = <3200000>; - firmware-name = "crnv21.bin"; - clocks = <&rpmhcc RPMH_RF_CLK2>; - }; -};Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +18
-0@@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/qualcomm-bluetooth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Bluetooth Chips + +maintainers: + - Rob Herring <[email protected]> + - Marcel Holtmann <[email protected]> + +description: + This binding describes Qualcomm UART-attached bluetooth chips. + +properties: + compatible: + enum:
Quoted 9 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml line 24
Quoted 6 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +6
-0+ - qcom,qca6174-bt + - qcom,qca9377-bt + - qcom,wcn3990-bt + - qcom,wcn3991-bt + - qcom,wcn3998-bt + - qcom,qca6390-btdelete trailing blanks
[Venkata]:
I will update in next patchset.
Quoted 8 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml line 29
Quoted 5 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +5
-0+ + enable-gpios: + maxItems: 1 + description: gpio specifier used to enable chip +delete blanks
[Venkata]:
I will update in next patchset.
Quoted 11 lines
Quoted 11 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +11
-0+ clocks: + maxItems: 1 + description: clock provided to the controller (SUSCLK_32KHZ) + + vddio-supply: + description: VDD_IO supply regulator handle + + vddxo-supply: + description: VDD_XO supply regulator handle + + vddrf-supply:
Quoted 9 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml line 46
Quoted 6 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +6
-0+ description: VDD_RF supply regulator handle + + vddch0-supply: + description: VDD_CH0 supply regulator handle + + max-speed:delete trailing blank
[Venkata]:
I will update in next patchset.
Quoted 10 lines
Quoted 10 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +1
-0+ description: see
Documentation/devicetree/bindings/serial/serial.yamlDocumentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +6
-0+ + firmware-name: + description: specify the name of nvm firmware to load + + local-bd-address: + description: see
Documentation/devicetree/bindings/net/bluetooth.txt+
Quoted 9 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml line 57
Quoted 3 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +3
-0+ +required: + - compatibleit seems you could make the supplies conditionally required based on the compatible string. See
Documentation/devicetree/bindings/connector/usb-connector.yamlfor an example
[Venkata]:
I will update in next patchset
Quoted 22 lines
Quoted 22 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +22
-0+ +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + uart { + label = "BT-UART"; + status = "okay"; + + bluetooth { + compatible = "qcom,qca6174-bt"; + enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; + clocks = <&divclk4>; + firmware-name = "nvm_00440302.bin"; + }; + }; + - | + uart { + + bluetooth { + compatible = "qcom,wcn3990-bt";
Quoted 8 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml line 85
Quoted 6 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +6
-0+ vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>; + max-speed = <3200000>; + firmware-name = "crnv21.bin";delete trailing blanks
[Venkata]:
I will update in next patchset.
Regards,
Venkata.
Rob Herring
maintainerRe: [PATCH v2 2/3] dt-bindings: net: bluetooth: Convert to DT schema
In reply to Venkata Lakshmi Narayana GubbaQuoted 17 lines · Venkata Lakshmi Narayana Gubba
Converted Qualcomm Bluetooth binidings to DT schema.
Signed-off-by Venkata Lakshmi Narayana Gubba <[email protected]>--- .../devicetree/bindings/net/qualcomm-bluetooth.txt | 69 ----------------- .../bindings/net/qualcomm-bluetooth.yaml | 87 ++++++++++++++++++++++ 2 files changed, 87 insertions(+), 69 deletions(-) delete mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt create mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.yamlDocumentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +1
-0@@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml line 11
Quoted 10 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +10
-0+%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/qualcomm-bluetooth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Bluetooth Chips + +maintainers: + - Rob Herring <[email protected]> + - Marcel Holtmann <[email protected]>
This should be someone that knows and cares about this h/w. I don't.
Quoted 44 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +44
-0+ +description: + This binding describes Qualcomm UART-attached bluetooth chips. + +properties: + compatible: + enum: + - qcom,qca6174-bt + - qcom,qca9377-bt + - qcom,wcn3990-bt + - qcom,wcn3991-bt + - qcom,wcn3998-bt + - qcom,qca6390-bt + + enable-gpios: + maxItems: 1 + description: gpio specifier used to enable chip + + clocks: + maxItems: 1 + description: clock provided to the controller (SUSCLK_32KHZ) + + vddio-supply: + description: VDD_IO supply regulator handle + + vddxo-supply: + description: VDD_XO supply regulator handle + + vddrf-supply: + description: VDD_RF supply regulator handle + + vddch0-supply: + description: VDD_CH0 supply regulator handle + + max-speed: + description: see Documentation/devicetree/bindings/serial/serial.yaml + + firmware-name: + description: specify the name of nvm firmware to load + + local-bd-address: + description: see Documentation/devicetree/bindings/net/bluetooth.txt + +
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml line 65
Quoted 10 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +10
-0+required: + - compatible + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + uart { + label = "BT-UART";
Why do you need a label for in internal port where you've described the connection?
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml line 66
Quoted 1 line
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +1
-0+ status = "okay";
Don't show status in examples.
Quoted 25 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +21
-0+ + bluetooth { + compatible = "qcom,qca6174-bt"; + enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; + clocks = <&divclk4>; + firmware-name = "nvm_00440302.bin"; + }; + }; + - | + uart { + + bluetooth { + compatible = "qcom,wcn3990-bt"; + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>; + max-speed = <3200000>; + firmware-name = "crnv21.bin"; + }; + };Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
Re: [PATCH v2 2/3] dt-bindings: net: bluetooth: Convert to DT schema
Hi Rob Herring,
Quoted 26 lines · Rob Herring
Quoted 25 lines · Venkata Lakshmi Narayana Gubba
Converted Qualcomm Bluetooth binidings to DT schema.
Signed-off-by Venkata Lakshmi Narayana Gubba <[email protected]>--- .../devicetree/bindings/net/qualcomm-bluetooth.txt | 69 ----------------- .../bindings/net/qualcomm-bluetooth.yaml | 87 ++++++++++++++++++++++ 2 files changed, 87 insertions(+), 69 deletions(-) delete mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt create mode 100644
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yamlDocumentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +5
-0@@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/qualcomm-bluetooth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml#
Quoted 9 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml line 11
Quoted 6 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +6
-0+ +title: Qualcomm Bluetooth Chips + +maintainers: + - Rob Herring <[email protected]> + - Marcel Holtmann <[email protected]>This should be someone that knows and cares about this h/w. I don't.
[Venkata]:
I will remove your name in next patchset.
Quoted 51 lines
Quoted 51 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +36
-0+ +description: + This binding describes Qualcomm UART-attached bluetooth chips. + +properties: + compatible: + enum: + - qcom,qca6174-bt + - qcom,qca9377-bt + - qcom,wcn3990-bt + - qcom,wcn3991-bt + - qcom,wcn3998-bt + - qcom,qca6390-bt + + enable-gpios: + maxItems: 1 + description: gpio specifier used to enable chip + + clocks: + maxItems: 1 + description: clock provided to the controller (SUSCLK_32KHZ) + + vddio-supply: + description: VDD_IO supply regulator handle + + vddxo-supply: + description: VDD_XO supply regulator handle + + vddrf-supply: + description: VDD_RF supply regulator handle + + vddch0-supply: + description: VDD_CH0 supply regulator handle + + max-speed: + description: see
Documentation/devicetree/bindings/serial/serial.yamlDocumentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +6
-0+ + firmware-name: + description: specify the name of nvm firmware to load + + local-bd-address: + description: see
Documentation/devicetree/bindings/net/bluetooth.txtDocumentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +7
-0+ + +required: + - compatible + +additionalProperties: false +
Quoted 9 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml line 65
Quoted 5 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +5
-0+examples: + - | + #include <dt-bindings/gpio/gpio.h> + uart { + label = "BT-UART";Why do you need a label for in internal port where you've described the connection?
[Venkata]:
I will remove in next patchset.
Quoted 4 lines
Quoted 1 line
+ status = "okay";
Don't show status in examples.
[Venkata]:
Sure, I will remove in next patchset.
Quoted 17 lines
Quoted 17 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +17
-0+ + bluetooth { + compatible = "qcom,qca6174-bt"; + enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; + clocks = <&divclk4>; + firmware-name = "nvm_00440302.bin"; + }; + }; + - | + uart { + + bluetooth { + compatible = "qcom,wcn3990-bt"; + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>;
Quoted 8 lines
Quoted 8 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +4
-1+ max-speed = <3200000>; + firmware-name = "crnv21.bin"; + }; + }; --QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
Regards,
Venkata.
Rob Herring
maintainerRe: [PATCH v2 2/3] dt-bindings: net: bluetooth: Convert to DT schema
In reply to Venkata Lakshmi Narayana GubbaQuoted 145 lines · Venkata Lakshmi Narayana Gubba
Converted Qualcomm Bluetooth binidings to DT schema.
Signed-off-by Venkata Lakshmi Narayana Gubba <[email protected]>--- .../devicetree/bindings/net/qualcomm-bluetooth.txt | 69 ----------------- .../bindings/net/qualcomm-bluetooth.yaml | 87 ++++++++++++++++++++++ 2 files changed, 87 insertions(+), 69 deletions(-) delete mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt create mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.yamlDocumentation/devicetree/bindings/net/qualcomm-bluetooth.txt deleted +0
-69@@ -1,69 +0,0 @@ -Qualcomm Bluetooth Chips ---------------------- - -This documents the binding structure and common properties for serial -attached Qualcomm devices. - -Serial attached Qualcomm devices shall be a child node of the host UART -device the slave device is attached to. - -Required properties: - - compatible: should contain one of the following: - * "qcom,qca6174-bt" - * "qcom,qca9377-bt" - * "qcom,wcn3990-bt" - * "qcom,wcn3991-bt" - * "qcom,wcn3998-bt" - * "qcom,qca6390-bt" - -Optional properties for compatible string qcom,qca6174-bt: - - - enable-gpios: gpio specifier used to enable chip - - clocks: clock provided to the controller (SUSCLK_32KHZ) - - firmware-name: specify the name of nvm firmware to load - -Optional properties for compatible string qcom,qca9377-bt: - - - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml - -Required properties for compatible string qcom,wcn399x-bt: - - - vddio-supply: VDD_IO supply regulator handle. - - vddxo-supply: VDD_XO supply regulator handle. - - vddrf-supply: VDD_RF supply regulator handle. - - vddch0-supply: VDD_CH0 supply regulator handle. - -Optional properties for compatible string qcom,wcn399x-bt: - - - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml - - firmware-name: specify the name of nvm firmware to load - - clocks: clock provided to the controller - -Examples: - -serial@7570000 { - label = "BT-UART"; - status = "okay"; - - bluetooth { - compatible = "qcom,qca6174-bt"; - - enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; - clocks = <&divclk4>; - firmware-name = "nvm_00440302.bin"; - }; -}; - -serial@898000 { - bluetooth { - compatible = "qcom,wcn3990-bt"; - - vddio-supply = <&vreg_s4a_1p8>; - vddxo-supply = <&vreg_l7a_1p8>; - vddrf-supply = <&vreg_l17a_1p3>; - vddch0-supply = <&vreg_l25a_3p3>; - max-speed = <3200000>; - firmware-name = "crnv21.bin"; - clocks = <&rpmhcc RPMH_RF_CLK2>; - }; -};Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +54
-0@@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/qualcomm-bluetooth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Bluetooth Chips + +maintainers: + - Rob Herring <[email protected]> + - Marcel Holtmann <[email protected]> + +description: + This binding describes Qualcomm UART-attached bluetooth chips. + +properties: + compatible: + enum: + - qcom,qca6174-bt + - qcom,qca9377-bt + - qcom,wcn3990-bt + - qcom,wcn3991-bt + - qcom,wcn3998-bt + - qcom,qca6390-bt + + enable-gpios: + maxItems: 1 + description: gpio specifier used to enable chip + + clocks: + maxItems: 1 + description: clock provided to the controller (SUSCLK_32KHZ) + + vddio-supply: + description: VDD_IO supply regulator handle + + vddxo-supply: + description: VDD_XO supply regulator handle + + vddrf-supply: + description: VDD_RF supply regulator handle + + vddch0-supply: + description: VDD_CH0 supply regulator handle + + max-speed: + description: see Documentation/devicetree/bindings/serial/serial.yaml + + firmware-name: + description: specify the name of nvm firmware to load + + local-bd-address: + description: see Documentation/devicetree/bindings/net/bluetooth.txt +
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml line 64
Quoted 10 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +10
-0+ +required: + - compatible + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + uart {
Also, 'serial' is the proper node name.
Quoted 27 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +23
-0+ label = "BT-UART"; + status = "okay"; + + bluetooth { + compatible = "qcom,qca6174-bt"; + enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; + clocks = <&divclk4>; + firmware-name = "nvm_00440302.bin"; + }; + }; + - | + uart { + + bluetooth { + compatible = "qcom,wcn3990-bt"; + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>; + max-speed = <3200000>; + firmware-name = "crnv21.bin"; + }; + };Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
Re: [PATCH v2 2/3] dt-bindings: net: bluetooth: Convert to DT schema
Hi Rob Herring,
Quoted 159 lines · Rob Herring
Quoted 158 lines · Venkata Lakshmi Narayana Gubba
Converted Qualcomm Bluetooth binidings to DT schema.
Signed-off-by Venkata Lakshmi Narayana Gubba <[email protected]>--- .../devicetree/bindings/net/qualcomm-bluetooth.txt | 69 ----------------- .../bindings/net/qualcomm-bluetooth.yaml | 87 ++++++++++++++++++++++ 2 files changed, 87 insertions(+), 69 deletions(-) delete mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt create mode 100644
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yamlDocumentation/devicetree/bindings/net/qualcomm-bluetooth.txt deleted +0
-7@@ -1,69 +0,0 @@ -Qualcomm Bluetooth Chips ---------------------- - -This documents the binding structure and common properties for serial -attached Qualcomm devices. - -Serial attached Qualcomm devices shall be a child node of the hostUART
Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt deleted +0
-20-device the slave device is attached to. - -Required properties: - - compatible: should contain one of the following: - * "qcom,qca6174-bt" - * "qcom,qca9377-bt" - * "qcom,wcn3990-bt" - * "qcom,wcn3991-bt" - * "qcom,wcn3998-bt" - * "qcom,qca6390-bt" - -Optional properties for compatible string qcom,qca6174-bt: - - - enable-gpios: gpio specifier used to enable chip - - clocks: clock provided to the controller (SUSCLK_32KHZ) - - firmware-name: specify the name of nvm firmware to load - -Optional properties for compatible string qcom,qca9377-bt: - - - max-speed: see
Documentation/devicetree/bindings/serial/serial.yamlDocumentation/devicetree/bindings/net/qualcomm-bluetooth.txt deleted +0
-11- -Required properties for compatible string qcom,wcn399x-bt: - - - vddio-supply: VDD_IO supply regulator handle. - - vddxo-supply: VDD_XO supply regulator handle. - - vddrf-supply: VDD_RF supply regulator handle. - - vddch0-supply: VDD_CH0 supply regulator handle. - -Optional properties for compatible string qcom,wcn399x-bt: - - - max-speed: see
Documentation/devicetree/bindings/serial/serial.yaml
- - firmware-name: specify the name of nvm firmware to load
- - clocks: clock provided to the controllerDocumentation/devicetree/bindings/net/qualcomm-bluetooth.txt deleted +0
-29- -Examples: - -serial@7570000 { - label = "BT-UART"; - status = "okay"; - - bluetooth { - compatible = "qcom,qca6174-bt"; - - enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; - clocks = <&divclk4>; - firmware-name = "nvm_00440302.bin"; - }; -}; - -serial@898000 { - bluetooth { - compatible = "qcom,wcn3990-bt"; - - vddio-supply = <&vreg_s4a_1p8>; - vddxo-supply = <&vreg_l7a_1p8>; - vddrf-supply = <&vreg_l17a_1p3>; - vddch0-supply = <&vreg_l25a_3p3>; - max-speed = <3200000>; - firmware-name = "crnv21.bin"; - clocks = <&rpmhcc RPMH_RF_CLK2>; - }; -};Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +47
-0@@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/qualcomm-bluetooth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Bluetooth Chips + +maintainers: + - Rob Herring <[email protected]> + - Marcel Holtmann <[email protected]> + +description: + This binding describes Qualcomm UART-attached bluetooth chips. + +properties: + compatible: + enum: + - qcom,qca6174-bt + - qcom,qca9377-bt + - qcom,wcn3990-bt + - qcom,wcn3991-bt + - qcom,wcn3998-bt + - qcom,qca6390-bt + + enable-gpios: + maxItems: 1 + description: gpio specifier used to enable chip + + clocks: + maxItems: 1 + description: clock provided to the controller (SUSCLK_32KHZ) + + vddio-supply: + description: VDD_IO supply regulator handle + + vddxo-supply: + description: VDD_XO supply regulator handle + + vddrf-supply: + description: VDD_RF supply regulator handle + + vddch0-supply: + description: VDD_CH0 supply regulator handle + + max-speed: + description: see
Documentation/devicetree/bindings/serial/serial.yamlDocumentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +6
-0+ + firmware-name: + description: specify the name of nvm firmware to load + + local-bd-address: + description: see
Documentation/devicetree/bindings/net/bluetooth.txtDocumentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +5
-0+ + +required: + - compatible +
Quoted 9 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml line 64
Quoted 6 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +6
-0+additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + uart {Also, 'serial' is the proper node name.
[Venkata]:
Sure, I will update in next patchset.
Quoted 19 lines
Quoted 19 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +19
-0+ label = "BT-UART"; + status = "okay"; + + bluetooth { + compatible = "qcom,qca6174-bt"; + enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; + clocks = <&divclk4>; + firmware-name = "nvm_00440302.bin"; + }; + }; + - | + uart { + + bluetooth { + compatible = "qcom,wcn3990-bt"; + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>;
Quoted 8 lines
Quoted 8 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file +4
-1+ max-speed = <3200000>; + firmware-name = "crnv21.bin"; + }; + }; --QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
Regards,
Venkata.
PATCH v2 3/3 dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750
In reply to Venkata Lakshmi Narayana GubbaThis patch enables regulators and gpios for the Qualcomm Bluetooth wcn6750 controller.
--- .../bindings/net/qualcomm-bluetooth.yaml | 54 +++++++++++++++++++++- 1 file changed, 53 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml +53 -1
@@ -21,11 +21,17 @@ properties: - qcom,wcn3990-bt - qcom,wcn3991-bt - qcom,wcn3998-bt - - qcom,qca6390-bt + - qcom,qca6390-bt + - qcom,wcn6750-bt enable-gpios: maxItems: 1 description: gpio specifier used to enable chip + + swctrl-gpios: + maxItems: 1 + description: gpio specifier is used to find status + of clock supply to SoC clocks: maxItems: 1
@@ -43,6 +49,30 @@ properties: vddch0-supply: description: VDD_CH0 supply regulator handle + vddaon-supply: + description: VDD_AON supply regulator handle + + vddbtcxmx-supply: + description: VDD_BT_CXMX supply regualtor handle + + vddrfacmn-supply: + description: VDD_RFA_CMN supply regulator handle + + vddrfa0p8-supply: + description: VDD_RFA_0P8 suppply regulator handle + + vddrfa1p7-supply: + description: VDD_RFA_1P7 supply regulator handle + + vddrfa1p2-supply: + description: VDD_RFA_1P2 supply regulator handle + + vddrfa2p2-supply: + description: VDD_RFA_2P2 supply regulator handle + + vddasd-supply: + description: VDD_ASD supply regulator handle + max-speed: description: see Documentation/devicetree/bindings/serial/serial.yaml
@@ -85,3 +115,25 @@ examples: firmware-name = "crnv21.bin"; }; }; + - | + uart { + + bluetooth { + compatible = "qcom,wcn6750-bt"; + pinctrl-names = "default"; + pinctrl-0 = <&bt_en_default>; + enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; + swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>; + vddio-supply = <&vreg_l19b_1p8>; + vddaon-supply = <&vreg_s7b_0p9>; + vddbtcxmx-supply = <&vreg_s7b_0p9>; + vddrfacmn-supply = <&vreg_s7b_0p9>; + vddrfa0p8-supply = <&vreg_s7b_0p9>; + vddrfa1p7-supply = <&vreg_s1b_1p8>; + vddrfa1p2-supply = <&vreg_s8b_1p2>; + vddrfa2p2-supply = <&vreg_s1c_2p2>; + vddasd-supply = <&vreg_l11c_2p8>; + max-speed = <3200000>; + firmware-name = "msnv11.bin"; + }; + };
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
Rob Herring
maintainerRe: [PATCH v2 3/3] dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750
Quoted 32 lines · Venkata Lakshmi Narayana Gubba
This patch enables regulators and gpios for the Qualcomm Bluetooth wcn6750 controller.
Signed-off-by Venkata Lakshmi Narayana Gubba <[email protected]>--- .../bindings/net/qualcomm-bluetooth.yaml | 54 +++++++++++++++++++++- 1 file changed, 53 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml +7
-1@@ -21,11 +21,17 @@ properties: - qcom,wcn3990-bt - qcom,wcn3991-bt - qcom,wcn3998-bt - - qcom,qca6390-bt + - qcom,qca6390-bt + - qcom,wcn6750-bt enable-gpios: maxItems: 1 description: gpio specifier used to enable chip + + swctrl-gpios: + maxItems: 1 + description: gpio specifier is used to find status + of clock supply to SoC clocks: maxItems: 1
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml properties: · line 56
Quoted 8 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml +5
-0@@ -43,6 +49,30 @@ properties: vddch0-supply: description: VDD_CH0 supply regulator handle + vddaon-supply: + description: VDD_AON supply regulator handle + + vddbtcxmx-supply: + description: VDD_BT_CXMX supply regualtor handle
typo
Quoted 23 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml +19
-0+ + vddrfacmn-supply: + description: VDD_RFA_CMN supply regulator handle + + vddrfa0p8-supply: + description: VDD_RFA_0P8 suppply regulator handle + + vddrfa1p7-supply: + description: VDD_RFA_1P7 supply regulator handle + + vddrfa1p2-supply: + description: VDD_RFA_1P2 supply regulator handle + + vddrfa2p2-supply: + description: VDD_RFA_2P2 supply regulator handle + + vddasd-supply: + description: VDD_ASD supply regulator handle + max-speed: description: see Documentation/devicetree/bindings/serial/serial.yaml
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml examples: · line 119
Quoted 5 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml +2
-0@@ -85,3 +115,25 @@ examples: firmware-name = "crnv21.bin"; }; }; + - | + uart {
serial {
Quoted 24 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml +20
-0+ + bluetooth { + compatible = "qcom,wcn6750-bt"; + pinctrl-names = "default"; + pinctrl-0 = <&bt_en_default>; + enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; + swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>; + vddio-supply = <&vreg_l19b_1p8>; + vddaon-supply = <&vreg_s7b_0p9>; + vddbtcxmx-supply = <&vreg_s7b_0p9>; + vddrfacmn-supply = <&vreg_s7b_0p9>; + vddrfa0p8-supply = <&vreg_s7b_0p9>; + vddrfa1p7-supply = <&vreg_s1b_1p8>; + vddrfa1p2-supply = <&vreg_s8b_1p2>; + vddrfa2p2-supply = <&vreg_s1c_2p2>; + vddasd-supply = <&vreg_l11c_2p8>; + max-speed = <3200000>; + firmware-name = "msnv11.bin"; + }; + };Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
Re: [PATCH v2 3/3] dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750
Hi Rob Herring,
Quoted 37 lines · Rob Herring
Quoted 36 lines · Venkata Lakshmi Narayana Gubba
This patch enables regulators and gpios for the Qualcomm Bluetooth wcn6750 controller.
Signed-off-by Venkata Lakshmi Narayana Gubba <[email protected]>--- .../bindings/net/qualcomm-bluetooth.yaml | 54 +++++++++++++++++++++- 1 file changed, 53 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml +7
-1@@ -21,11 +21,17 @@ properties: - qcom,wcn3990-bt - qcom,wcn3991-bt - qcom,wcn3998-bt - - qcom,qca6390-bt + - qcom,qca6390-bt + - qcom,wcn6750-bt enable-gpios: maxItems: 1 description: gpio specifier used to enable chip + + swctrl-gpios: + maxItems: 1 + description: gpio specifier is used to find status + of clock supply to SoC clocks: maxItems: 1@@ -43,6 +49,30 @@ properties: vddch0-supply: description: VDD_CH0 supply regulator handle
Quoted 8 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml properties: · line 56
Quoted 5 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml +5
-0+ vddaon-supply: + description: VDD_AON supply regulator handle + + vddbtcxmx-supply: + description: VDD_BT_CXMX supply regualtor handletypo
[Venkata]:
I will update in next patchset.
Quoted 23 lines
Quoted 23 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml +19
-0+ + vddrfacmn-supply: + description: VDD_RFA_CMN supply regulator handle + + vddrfa0p8-supply: + description: VDD_RFA_0P8 suppply regulator handle + + vddrfa1p7-supply: + description: VDD_RFA_1P7 supply regulator handle + + vddrfa1p2-supply: + description: VDD_RFA_1P2 supply regulator handle + + vddrfa2p2-supply: + description: VDD_RFA_2P2 supply regulator handle + + vddasd-supply: + description: VDD_ASD supply regulator handle + max-speed: description: see
Documentation/devicetree/bindings/serial/serial.yaml
Quoted 9 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml examples: · line 119
Quoted 6 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml +2
-0@@ -85,3 +115,25 @@ examples: firmware-name = "crnv21.bin"; }; }; + - | + uart {serial {
[Venkata]:
Sure, I will update in next patchset.
Quoted 16 lines
Quoted 16 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml +16
-0+ + bluetooth { + compatible = "qcom,wcn6750-bt"; + pinctrl-names = "default"; + pinctrl-0 = <&bt_en_default>; + enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; + swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>; + vddio-supply = <&vreg_l19b_1p8>; + vddaon-supply = <&vreg_s7b_0p9>; + vddbtcxmx-supply = <&vreg_s7b_0p9>; + vddrfacmn-supply = <&vreg_s7b_0p9>; + vddrfa0p8-supply = <&vreg_s7b_0p9>; + vddrfa1p7-supply = <&vreg_s1b_1p8>; + vddrfa1p2-supply = <&vreg_s8b_1p2>; + vddrfa2p2-supply = <&vreg_s1c_2p2>; + vddasd-supply = <&vreg_l11c_2p8>;
Quoted 8 lines
Quoted 8 lines
Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml +4
-1+ max-speed = <3200000>; + firmware-name = "msnv11.bin"; + }; + }; --QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
Regards,
Venkata.