Guest system time jumps when new vCPUs is hot-added
PATCH 1/1 Guest system time jumps when new vCPUs is hot-added
Hello,
I have below VM configuration:
...
<vcpu placement='static' current='1'>2</vcpu>
<cpu mode='host-passthrough'>
</cpu>
<clock offset='utc'>
<timer name='tsc' frequency='3000000000'/>
</clock>
...
After VM has been up for a few minutes, I use "virsh setvcpus" to hot-add
second vCPU into VM, below dmesg is observed:
[ 53.273484] CPU1 has been hot-added
[ 85.067135] SMP alternatives: switching to SMP code
[ 85.078409] x86: Booting SMP configuration:
[ 85.079027] smpboot: Booting Node 0 Processor 1 APIC 0x1
[ 85.080240] kvm-clock: cpu 1, msr 77601041, secondary cpu clock
[ 85.080450] smpboot: CPU 1 Converting physical 0 to logical die 1
[ 85.101228] TSC ADJUST compensate: CPU1 observed 169175101528 warp. Adjust: 169175101528
[ 141.513496] TSC ADJUST compensate: CPU1 observed 166 warp. Adjust: 169175101694
[ 141.513496] TSC synchronization [CPU#0 -> CPU#1]:
[ 141.513496] Measured 235 cycles TSC warp between CPUs, turning off TSC clock.
[ 141.513496] tsc: Marking TSC unstable due to check_tsc_sync_source failed
[ 141.543996] KVM setup async PF for cpu 1
[ 141.544281] kvm-stealtime: cpu 1, msr 13bd2c080
[ 141.549381] Will online and init hotplugged CPU: 1System time jumps from 85.101228 to 141.51.3496.
Guest: KVM
----- ------check_tsc_sync_target()wrmsrl(MSR_IA32_TSC_ADJUST,...)
kvm_set_msr_common(vcpu,...) adjust_tsc_offset_guest(vcpu,...) //tsc_offset jumped vcpu_enter_guest(vcpu) //tsc_timestamp was not changed
...rdtsc() jumped, system time jumped
tsc_timestamp must be updated before go back to guest.
---
Zelin Deng (1):
KVM: x86: Update vCPU's hv_clock before back to guest when tsc_offset
is adjusted
arch/x86/kvm/x86.c | 4 ++++ 1 file changed, 4 insertions(+)
Signature · 1 line
1.8.3.1
PATCH 1/1 KVM: x86: Update vCPU's hv_clock before back to guest when tsc_offset is adjusted
When MSR_IA32_TSC_ADJUST is written by guest due to TSC ADJUST feature especially there's a big tsc warp (like a new vCPU is hot-added into VM which has been up for a long time), tsc_offset is added by a large value then go back to guest. This causes system time jump as tsc_timestamp is not adjusted in the meantime and pvclock monotonic character. To fix this, just notify kvm to update vCPU's guest time before back to guest.
--- arch/x86/kvm/x86.c | 4 ++++ 1 file changed, 4 insertions(+)
arch/x86/kvm/x86.c +4 -0
@@ -3095,6 +3095,10 @@ int kvm_set_msr_common(struct kvm_vcpu *vcpu, struct msr_data *msr_info)if (!msr_info->host_initiated) {s64 adj = data - vcpu->arch.ia32_tsc_adjust_msr;adjust_tsc_offset_guest (vcpu, adj); +/* Before back to guest, tsc_timestamp must be adjusted +* as well, otherwise guest's percpu pvclock time could jump. +*/ +kvm_make_request (KVM_REQ_CLOCK_UPDATE , vcpu); } vcpu->arch.ia32_tsc_adjust_msr = data; }
Signature · 1 line
1.8.3.1
Quoted 12 lines · Zelin Deng
Hello,
I have below VM configuration:
...<vcpu placement='static' current='1'>2</vcpu> <cpu mode='host-passthrough'> </cpu> <clock offset='utc'> <timer name='tsc' frequency='3000000000'/> </clock>...
After VM has been up for a few minutes, I use "virsh setvcpus" to hot-add second vCPU into VM, below dmesg is observed:
Quoted 8 lines
[ 53.273484] CPU1 has been hot-added [ 85.067135] SMP alternatives: switching to SMP code [ 85.078409] x86: Booting SMP configuration: [ 85.079027] smpboot: Booting Node 0 Processor 1 APIC 0x1 [ 85.080240] kvm-clock: cpu 1, msr 77601041, secondary cpu clock [ 85.080450] smpboot: CPU 1 Converting physical 0 to logical die 1 [ 85.101228] TSC ADJUST compensate: CPU1 observed 169175101528 warp. Adjust: 169175101528 [ 141.513496] TSC ADJUST compensate: CPU1 observed 166 warp. Adjust: 169175101694
Why is TSC_ADJUST on CPU1 different from CPU0 in the first place?
That's broken.
Thanks,
tglx
Quoted 23 lines · Thomas Gleixner
Quoted 12 lines · Zelin Deng
Hello,
I have below VM configuration:
...<vcpu placement='static' current='1'>2</vcpu> <cpu mode='host-passthrough'> </cpu> <clock offset='utc'> <timer name='tsc' frequency='3000000000'/> </clock>...
After VM has been up for a few minutes, I use "virsh setvcpus" to hot-add second vCPU into VM, below dmesg is observed:Quoted 8 lines
[ 53.273484] CPU1 has been hot-added [ 85.067135] SMP alternatives: switching to SMP code [ 85.078409] x86: Booting SMP configuration: [ 85.079027] smpboot: Booting Node 0 Processor 1 APIC 0x1 [ 85.080240] kvm-clock: cpu 1, msr 77601041, secondary cpu clock [ 85.080450] smpboot: CPU 1 Converting physical 0 to logical die 1 [ 85.101228] TSC ADJUST compensate: CPU1 observed 169175101528 warp. Adjust: 169175101528 [ 141.513496] TSC ADJUST compensate: CPU1 observed 166 warp. Adjust: 169175101694
Quoted 3 lines
Why is
TSC_ADJUSTon CPU1 different from CPU0 in the first place?That's broken.
Aside of that the TSC synchronization check in guests cannot work reliably at all. Simply because there is no guarantee that vCPU0 and vCPU1 are running in parallel.
Thanks,
tglx
Quoted 22 lines · Thomas Gleixner
Quoted 12 lines · Zelin Deng
Hello,
I have below VM configuration:
...<vcpu placement='static' current='1'>2</vcpu> <cpu mode='host-passthrough'> </cpu> <clock offset='utc'> <timer name='tsc' frequency='3000000000'/> </clock>...
After VM has been up for a few minutes, I use "virsh setvcpus" to hot-add second vCPU into VM, below dmesg is observed:Quoted 8 lines
[ 53.273484] CPU1 has been hot-added [ 85.067135] SMP alternatives: switching to SMP code [ 85.078409] x86: Booting SMP configuration: [ 85.079027] smpboot: Booting Node 0 Processor 1 APIC 0x1 [ 85.080240] kvm-clock: cpu 1, msr 77601041, secondary cpu clock [ 85.080450] smpboot: CPU 1 Converting physical 0 to logical die 1 [ 85.101228] TSC ADJUST compensate: CPU1 observed 169175101528 warp. Adjust: 169175101528 [ 141.513496] TSC ADJUST compensate: CPU1 observed 166 warp. Adjust: 169175101694
Quoted 1 line
Why is
TSC_ADJUSTon CPU1 different from CPU0 in the first place?
Per my understanding when vCPU is created by KVM, it's tsc_offset = 0 - host rdtsc() meanwhile TSC_ADJUST is 0.
Assume vCPU0 boots up with tsc_offset0, after 10000 tsc cycles, hotplug via "virsh setvcpus" creates a new vCPU1 whose tsc_offset1 should be about tsc_offset0 - 10000. Therefore there's 10000 tsc warp between rdtsc() in guest of vCPU0 and vCPU1, check_tsc_sync_target() when vCPU1 gets online will set TSC_ADJUST for vCPU1.
Did I miss something?
Quoted 6 lines
That's broken.
Thanks,
tglx
Quoted 9 lines · Zelin Deng
Quoted 4 lines · Thomas Gleixner
Quoted 2 lines · Zelin Deng
[ 85.101228] TSC ADJUST compensate: CPU1 observed 169175101528 warp. Adjust: 169175101528 [ 141.513496] TSC ADJUST compensate: CPU1 observed 166 warp. Adjust: 169175101694Why is
TSC_ADJUSTon CPU1 different from CPU0 in the first place?Per my understanding when vCPU is created by KVM, it's
tsc_offset= 0 - hostrdtsc()meanwhileTSC_ADJUSTis 0.
Quoted 7 lines
Assume vCPU0 boots up with
tsc_offset0, after 10000 tsc cycles, hotplug via "virsh setvcpus" creates a new vCPU1 whosetsc_offset1should be abouttsc_offset0- 10000. Therefore there's 10000 tsc warp betweenrdtsc()in guest of vCPU0 and vCPU1,check_tsc_sync_target()when vCPU1 gets online will setTSC_ADJUSTfor vCPU1.Did I miss something?
Yes. The above is wrong.
The host has to ensure that the TSC of the vCPUs is in sync and if it exposes TSC_ADJUST then that should be 0 and nothing else. The TSC in a guest vCPU is
hostTSC + host_TSC_ADJUST + vcpu_TSC_OFFSET + vcpu_guest_TSC_ADJUST
The mechanism the host has to use to ensure that the guest vCPUs are exposing the same time is vcpu_TSC_OFFSET and nothing else. And vcpu_TSC_OFFSET is the same for all vCPUs of a guest.
Now there is another issue when vCPU0 and vCPU1 are on different 'sockets' via the topology information provided by the hypervisor.
Because we had quite some issues in the past where TSCs on a single socket were perfectly fine, but between sockets they were skewed, we have a sanity check there. What it does is:
if (cpu_is_first_on_non_boot_socket(cpu))
validate_synchronization_with_boot_socket()
And that validation expects that the CPUs involved run in a tight loop concurrently so the TSC readouts which happen on both can be reliably compared.
But this cannot be guaranteed on vCPUs at all, because the host can schedule out one or both at any point during that synchronization check.
A two socket guest setup needs to have information from the host that TSC is usable and that the socket sync check can be skipped. Anything else is just doomed to fail in hard to diagnose ways.
Thanks,
tglx
Quoted 22 lines · Thomas Gleixner
Quoted 8 lines · Zelin Deng
Quoted 4 lines · Thomas Gleixner
Quoted 2 lines · Zelin Deng
[ 85.101228] TSC ADJUST compensate: CPU1 observed 169175101528 warp. Adjust: 169175101528 [ 141.513496] TSC ADJUST compensate: CPU1 observed 166 warp. Adjust: 169175101694Why is
TSC_ADJUSTon CPU1 different from CPU0 in the first place?Per my understanding when vCPU is created by KVM, it's
tsc_offset= 0 - hostrdtsc()meanwhileTSC_ADJUSTis 0.Quoted 7 lines
Assume vCPU0 boots up with
tsc_offset0, after 10000 tsc cycles, hotplug via "virsh setvcpus" creates a new vCPU1 whosetsc_offset1should be abouttsc_offset0- 10000. Therefore there's 10000 tsc warp betweenrdtsc()in guest of vCPU0 and vCPU1,check_tsc_sync_target()when vCPU1 gets online will setTSC_ADJUSTfor vCPU1.Did I miss something?
Yes. The above is wrong.
The host has to ensure that the TSC of the vCPUs is in sync and if it exposes
TSC_ADJUSTthen that should be 0 and nothing else. The TSC in a guest vCPU is
Quoted 5 lines
hostTSC +
host_TSC_ADJUST+vcpu_TSC_OFFSET+vcpu_guest_TSC_ADJUSTThe mechanism the host has to use to ensure that the guest vCPUs are exposing the same time is
vcpu_TSC_OFFSETand nothing else. Andvcpu_TSC_OFFSETis the same for all vCPUs of a guest.
Yes, make sense.
Quoted 11 lines
Now there is another issue when vCPU0 and vCPU1 are on different 'sockets' via the topology information provided by the hypervisor.
Because we had quite some issues in the past where TSCs on a single socket were perfectly fine, but between sockets they were skewed, we have a sanity check there. What it does is:
if (
cpu_is_first_on_non_boot_socket(cpu))
validate_synchronization_with_boot_socket()
Quoted 6 lines
And that validation expects that the CPUs involved run in a tight loop concurrently so the TSC readouts which happen on both can be reliably compared.
But this cannot be guaranteed on vCPUs at all, because the host can schedule out one or both at any point during that synchronization check.
Is there any plan to fix this?
Quoted 4 lines
A two socket guest setup needs to have information from the host that TSC is usable and that the socket sync check can be skipped. Anything else is just doomed to fail in hard to diagnose ways.
Yes, I had tried to add "tsc=unstable" to skip tsc sync. However if a user process which is not pined to vCPU is using rdtsc, it can get tsc warp, because it can be scheduled among vCPUs. Does it mean user applications have to guarantee itself to use rdtsc only when TSC is reliable?
Quoted 4 lines
Thanks,
tglx
Quoted 10 lines · Zelin Deng
Quoted 7 lines · Thomas Gleixner
And that validation expects that the CPUs involved run in a tight loop concurrently so the TSC readouts which happen on both can be reliably compared.
But this cannot be guaranteed on vCPUs at all, because the host can schedule out one or both at any point during that synchronization check.
Is there any plan to fix this?
The above cannot be fixed.
As I said before the solution is:
Quoted 5 lines
Quoted 3 lines
A two socket guest setup needs to have information from the host that TSC is usable and that the socket sync check can be skipped. Anything else is just doomed to fail in hard to diagnose ways.
Yes, I had tried to add "tsc=unstable" to skip tsc sync. However if a
tsc=unstable? Oh well.
Quoted 2 lines
user process which is not pined to vCPU is using rdtsc, it can get tsc warp, because it can be scheduled among vCPUs. Does it mean user
Only if the hypervisor is not doing the right thing and makes sure that all vCPUs have the same tsc offset vs. the host TSC.
Quoted 2 lines
applications have to guarantee itself to use rdtsc only when TSC is reliable?
If the TSCs of CPUs are not in sync then the kernel does the right thing and uses some other clocksource for the various time interfaces, e.g. the kernel provides clock_getttime() which guarantees to be correct whether TSC is usable or not.
Any application using RDTSC directly is own their own and it's not a kernel problem.
The host kernel cannot make guarantees that the hardware is sane neither can a guest kernel make guarantees that the hypervisor is sane.
Thanks,
tglx
Got it. Many thanks, Thomas.
Quoted 44 lines · Thomas Gleixner
Quoted 9 lines · Zelin Deng
Quoted 7 lines · Thomas Gleixner
And that validation expects that the CPUs involved run in a tight loop concurrently so the TSC readouts which happen on both can be reliably compared.
But this cannot be guaranteed on vCPUs at all, because the host can schedule out one or both at any point during that synchronization check.
Is there any plan to fix this?
The above cannot be fixed.
As I said before the solution is:
Quoted 4 lines
Quoted 3 lines
A two socket guest setup needs to have information from the host that TSC is usable and that the socket sync check can be skipped. Anything else is just doomed to fail in hard to diagnose ways.
Yes, I had tried to add "tsc=unstable" to skip tsc sync. However if a
tsc=unstable? Oh well.
Quoted 2 lines
user process which is not pined to vCPU is using rdtsc, it can get tsc warp, because it can be scheduled among vCPUs. Does it mean user
Only if the hypervisor is not doing the right thing and makes sure that all vCPUs have the same tsc offset vs. the host TSC.
Quoted 2 lines
applications have to guarantee itself to use rdtsc only when TSC is reliable?
If the TSCs of CPUs are not in sync then the kernel does the right thing and uses some other clocksource for the various time interfaces, e.g. the kernel provides
clock_getttime()which guarantees to be correct whether TSC is usable or not.Any application using RDTSC directly is own their own and it's not a kernel problem.
The host kernel cannot make guarantees that the hardware is sane neither can a guest kernel make guarantees that the hypervisor is sane.
Thanks,
tglx
Paolo Bonzini
maintainerQuoted 41 lines · Zelin Deng
Hello,
I have below VM configuration:
...<vcpu placement='static' current='1'>2</vcpu> <cpu mode='host-passthrough'> </cpu> <clock offset='utc'> <timer name='tsc' frequency='3000000000'/> </clock> ... After VM has been up for a few minutes, I use "virsh setvcpus" to hot-add second vCPU into VM, below dmesg is observed: [ 53.273484] CPU1 has been hot-added [ 85.067135] SMP alternatives: switching to SMP code [ 85.078409] x86: Booting SMP configuration: [ 85.079027] smpboot: Booting Node 0 Processor 1 APIC 0x1 [ 85.080240] kvm-clock: cpu 1, msr 77601041, secondary cpu clock [ 85.080450] smpboot: CPU 1 Converting physical 0 to logical die 1 [ 85.101228] TSC ADJUST compensate: CPU1 observed 169175101528 warp. Adjust: 169175101528 [ 141.513496] TSC ADJUST compensate: CPU1 observed 166 warp. Adjust: 169175101694 [ 141.513496] TSC synchronization [CPU#0 -> CPU#1]: [ 141.513496] Measured 235 cycles TSC warp between CPUs, turning off TSC clock. [ 141.513496] tsc: Marking TSC unstable due to check_tsc_sync_source failed [ 141.543996] KVM setup async PF for cpu 1 [ 141.544281] kvm-stealtime: cpu 1, msr 13bd2c080 [ 141.549381] Will online and init hotplugged CPU: 1System time jumps from 85.101228 to 141.51.3496.
Guest: KVM
----- ------check_tsc_sync_target()wrmsrl(MSR_IA32_TSC_ADJUST,...)
kvm_set_msr_common(vcpu,...)adjust_tsc_offset_guest(vcpu,...)//tsc_offset jumpedvcpu_enter_guest(vcpu)//tsc_timestamp was not changed
...rdtsc()jumped, system time jumped
tsc_timestampmust be updated before go back to guest.
Quoted 8 lines
---
Zelin Deng (1):
KVM: x86: Update vCPU'shv_clockbefore back to guest whentsc_offset
is adjustedarch/x86/kvm/x86.c | 4 ++++ 1 file changed, 4 insertions(+)
While Thomas is right in general, what you found is indeed a bug with the KVM->userspace API to set up the vCPU TSC adjust. So I'm queueing the patch for 5.15.
Thanks,
Paolo