Skip to contentSkip to conversation

avoid raid1 resync abort

PATCH In review Paul Clements 2 participants 2 messages Aug 20, 2003 – Aug 22, 2003 MD RAID

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 avoid raid1 resync abort

Neil,

I don't know if you've noticed this one yet, but it looks like we need to set the master_bio->bi_bdev field at the beginning of every resync request. We use this value later on in sync_request_write() to determine whether a write should take place on a particular device. Without the field being properly set, we will end up aborting the resync process. This happens because the master_bios are pulled from a pool, so we eventually end up getting a master_bio that already has our destination disk set in its bi_bdev field. This causes sync_request_write() to fail since it thinks there is nowhere to write the data to.

The other minor bits in the patch are just some extra stuff that I found useful in debugging this problem, but are completely optional...

Thanks,
Paul

Index: drivers/md/raid1.c
===================================================================
RCS file: /home/cvs/CVSROOT/kernel/linux-2.6.0-test3/drivers/md/raid1.c,v retrieving revision 1.2

md/raid1.c +5 -2
diff -p -u -r1.2 raid1.c
@@ -771,8 +770,8 @@ static void print_conf(conf_t *conf)
 		char b[BDEVNAME_SIZE];
 		tmp = conf->mirrors + i;
 		if (tmp->rdev)
-			printk(" disk %d, wo:%d, o:%d, dev:%s\n",
-				i, !tmp->rdev->in_sync, !tmp->rdev->faulty,
+			printk(" disk %d, s:%d, f:%d, dev:%s\n",
+				i, tmp->rdev->in_sync, tmp->rdev->faulty,
 				bdevname(tmp->rdev->bdev,b));
 	}
 }
@@ -992,6 +991,8 @@ static void sync_request_write(mddev_t *
 	}
 
 	if (atomic_dec_and_test(&r1_bio->remaining)) {
+		PRINTK(KERN_DEBUG "raid1: sync write failed, no destination\n");
+		print_conf(conf);
 		md_done_sync(mddev, r1_bio->sector, bio->bi_size >> 9, 0);
 		put_buf(r1_bio);
 	}
@@ -1156,6 +1157,7 @@ static int sync_request(mddev_t *mddev, 
 	if (partial)
 		bio->bi_io_vec[bio->bi_vcnt-1].bv_len = partial;
 
+	bio->bi_bdev = mirror->rdev->bdev; /* we'd better set this */
 
 	read_bio = bio_clone(r1_bio->master_bio, GFP_NOIO);
 
#1 lore raw
Quoted 11 lines · On Wednesday August 20, [email protected] wrote:

Neil,

I don't know if you've noticed this one yet, but it looks like we need to set the master_bio->bi_bdev field at the beginning of every resync request. We use this value later on in sync_request_write() to determine whether a write should take place on a particular device. Without the field being properly set, we will end up aborting the resync process. This happens because the master_bios are pulled from a pool, so we eventually end up getting a master_bio that already has our destination disk set in its bi_bdev field. This causes sync_request_write() to fail since it thinks there is nowhere to write the data to.

Thanks. Your analysis looks right.
However it raises a question: why are we cloning a separate bio for reading instead of jus using the "master bio" ???

I'll have a deeper look at raid1 in a few days and see what I can find.

NeilBrown