Skip to contentSkip to conversation

DDR/L3 Scaling support on SC7280 SoCs

PATCH Superseded Sibi Sankar 2 participants 6 messages May 4, 2021 – May 5, 2021

Subsystems (5)
Device tree bindings Arm Qualcomm mailing list Arm Qualcomm support CPU frequency scaling framework +1 more subsystems

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore

Sibi Sankar

author
#0 lore raw

v2 cover DDR/L3 Scaling support on SC7280 SoCs

The patch series adds support for DDR/L3 Scaling on SC7280 SoCs.

V2:
* Add a new opp table for cpu 7 to account for the additional frequencies supported by it.

Depends on the following patch series:
L3 Provider Support: https://lore.kernel.org/lkml/[email protected]/
CPUfreq Support: https://lore.kernel.org/lkml/[email protected]/
RPMH Provider Support: https://lore.kernel.org/lkml/[email protected]/

It also depends on L3 and cpufreq dt nodes from the ^^ series to not have overlapping memory regions.

Sibi Sankar (2):
cpufreq: blacklist SC7280 in cpufreq-dt-platdev
arm64: dts: qcom: sc7280: Add cpu OPP tables

 arch/arm64/boot/dts/qcom/sc7280.dtsi | 215 +++++++++++++++++++++++++++++++++++
 drivers/cpufreq/cpufreq-dt-platdev.c |   1 +
 2 files changed, 216 insertions(+)
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
author
#1 lore raw

PATCH v2 1/2 cpufreq: blacklist SC7280 in cpufreq-dt-platdev

Add SC7280 to cpufreq-dt-platdev blacklist since the actual scaling is handled by the 'qcom-cpufreq-hw' driver.

Signed-off-by Sibi Sankar <[email protected]>
---
 drivers/cpufreq/cpufreq-dt-platdev.c | 1 +
 1 file changed, 1 insertion(+)
drivers/cpufreq/cpufreq-dt-platdev.c +1 -0
index 5e07065ec22f..345418b8250e 100644
@@ -137,6 +137,7 @@ static const struct of_device_id blacklist[] __initconst = {
 	{ .compatible = "qcom,msm8996", },
 	{ .compatible = "qcom,qcs404", },
 	{ .compatible = "qcom,sc7180", },
+	{ .compatible = "qcom,sc7280", },
 	{ .compatible = "qcom,sdm845", },
 
 	{ .compatible = "st,stih407", },
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
author
#3 lore raw

PATCH v2 2/2 arm64: dts: qcom: sc7280: Add cpu OPP tables

In reply to Sibi Sankar

Add OPP tables required to scale DDR/L3 per freq-domain on SC7280 SoCs.

Signed-off-by Sibi Sankar <[email protected]>

---

v2:
* Add a new opp table for cpu 7 to account for the additional frequencies supported by it.

 arch/arm64/boot/dts/qcom/sc7280.dtsi | 215 +++++++++++++++++++++++++++++++++++
 1 file changed, 215 insertions(+)
arch/arm64/boot/dts/qcom/sc7280.dtsi +215 -0
index 0bb835aeae33..34e9df7ea683 100644
@@ -7,6 +7,7 @@
 
 #include <dt-bindings/clock/qcom,gcc-sc7280.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/interconnect/qcom,osm-l3.h>
 #include <dt-bindings/interconnect/qcom,sc7280.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>

@@ -71,6 +72,9 @@
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
 			next-level-cache = <&L2_0>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
+					<&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			L2_0: l2-cache {
 				compatible = "cache";

@@ -90,6 +94,9 @@
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
 			next-level-cache = <&L2_100>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
+					<&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			L2_100: l2-cache {
 				compatible = "cache";

@@ -106,6 +113,9 @@
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
 			next-level-cache = <&L2_200>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
+					<&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			L2_200: l2-cache {
 				compatible = "cache";

@@ -122,6 +132,9 @@
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
 			next-level-cache = <&L2_300>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
+					<&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			L2_300: l2-cache {
 				compatible = "cache";

@@ -138,6 +151,9 @@
 					   &BIG_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
 			next-level-cache = <&L2_400>;
+			operating-points-v2 = <&cpu4_opp_table>;
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
+					<&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			L2_400: l2-cache {
 				compatible = "cache";

@@ -154,6 +170,9 @@
 					   &BIG_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
 			next-level-cache = <&L2_500>;
+			operating-points-v2 = <&cpu4_opp_table>;
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
+					<&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			L2_500: l2-cache {
 				compatible = "cache";

@@ -170,6 +189,9 @@
 					   &BIG_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
 			next-level-cache = <&L2_600>;
+			operating-points-v2 = <&cpu4_opp_table>;
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
+					<&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			L2_600: l2-cache {
 				compatible = "cache";

@@ -186,6 +208,9 @@
 					   &BIG_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
 			next-level-cache = <&L2_700>;
+			operating-points-v2 = <&cpu7_opp_table>;
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
+					<&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
 			qcom,freq-domain = <&cpufreq_hw 2>;
 			L2_700: l2-cache {
 				compatible = "cache";

@@ -248,6 +273,196 @@
 		};
 	};
 
+	cpu0_opp_table: cpu0_opp_table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		cpu0_opp1: opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			opp-peak-kBps = <800000 9600000>;
+		};
+
+		cpu0_opp2: opp-691200000 {
+			opp-hz = /bits/ 64 <691200000>;
+			opp-peak-kBps = <800000 17817600>;
+		};
+
+		cpu0_opp3: opp-806400000 {
+			opp-hz = /bits/ 64 <806400000>;
+			opp-peak-kBps = <800000 20889600>;
+		};
+
+		cpu0_opp4: opp-940800000 {
+			opp-hz = /bits/ 64 <940800000>;
+			opp-peak-kBps = <1804000 24576000>;
+		};
+
+		cpu0_opp5: opp-1152000000 {
+			opp-hz = /bits/ 64 <1152000000>;
+			opp-peak-kBps = <2188000 27033600>;
+		};
+
+		cpu0_opp6: opp-1324800000 {
+			opp-hz = /bits/ 64 <1324800000>;
+			opp-peak-kBps = <2188000 33792000>;
+		};
+
+		cpu0_opp7: opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+			opp-peak-kBps = <3072000 38092800>;
+		};
+
+		cpu0_opp8: opp-1651200000 {
+			opp-hz = /bits/ 64 <1651200000>;
+			opp-peak-kBps = <3072000 41779200>;
+		};
+
+		cpu0_opp9: opp-1804800000 {
+			opp-hz = /bits/ 64 <1804800000>;
+			opp-peak-kBps = <4068000 48537600>;
+		};
+
+		cpu0_opp10: opp-1958400000 {
+			opp-hz = /bits/ 64 <1958400000>;
+			opp-peak-kBps = <4068000 48537600>;
+		};
+	};
+
+	cpu4_opp_table: cpu4_opp_table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		cpu4_opp1: opp-691200000 {
+			opp-hz = /bits/ 64 <691200000>;
+			opp-peak-kBps = <1804000 9600000>;
+		};
+
+		cpu4_opp2: opp-940800000 {
+			opp-hz = /bits/ 64 <940800000>;
+			opp-peak-kBps = <2188000 17817600>;
+		};
+
+		cpu4_opp3: opp-1228800000 {
+			opp-hz = /bits/ 64 <1228800000>;
+			opp-peak-kBps = <4068000 24576000>;
+		};
+
+		cpu4_opp4: opp-1344000000 {
+			opp-hz = /bits/ 64 <1344000000>;
+			opp-peak-kBps = <4068000 24576000>;
+		};
+
+		cpu4_opp5: opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+			opp-peak-kBps = <4068000 24576000>;
+		};
+
+		cpu4_opp6: opp-1651200000 {
+			opp-hz = /bits/ 64 <1651200000>;
+			opp-peak-kBps = <6220000 38092800>;
+		};
+
+		cpu4_opp7: opp-1900800000 {
+			opp-hz = /bits/ 64 <1900800000>;
+			opp-peak-kBps = <6220000 44851200>;
+		};
+
+		cpu4_opp8: opp-2054400000 {
+			opp-hz = /bits/ 64 <2054400000>;
+			opp-peak-kBps = <6220000 44851200>;
+		};
+
+		cpu4_opp9: opp-2112000000 {
+			opp-hz = /bits/ 64 <2112000000>;
+			opp-peak-kBps = <6220000 44851200>;
+		};
+
+		cpu4_opp10: opp-2131200000 {
+			opp-hz = /bits/ 64 <2131200000>;
+			opp-peak-kBps = <6220000 44851200>;
+		};
+
+		cpu4_opp11: opp-2208000000 {
+			opp-hz = /bits/ 64 <2208000000>;
+			opp-peak-kBps = <6220000 44851200>;
+		};
+
+		cpu4_opp12: opp-2400000000 {
+			opp-hz = /bits/ 64 <2400000000>;
+			opp-peak-kBps = <8532000 48537600>;
+		};
+	};
+
+	cpu7_opp_table: cpu7_opp_table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		cpu7_opp1: opp-806400000 {
+			opp-hz = /bits/ 64 <806400000>;
+			opp-peak-kBps = <1804000 9600000>;
+		};
+
+		cpu7_opp2: opp-1056000000 {
+			opp-hz = /bits/ 64 <1056000000>;
+			opp-peak-kBps = <2188000 17817600>;
+		};
+
+		cpu7_opp3: opp-1324800000 {
+			opp-hz = /bits/ 64 <1324800000>;
+			opp-peak-kBps = <4068000 24576000>;
+		};
+
+		cpu7_opp4: opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+			opp-peak-kBps = <4068000 24576000>;
+		};
+
+		cpu7_opp5: opp-1766400000 {
+			opp-hz = /bits/ 64 <1766400000>;
+			opp-peak-kBps = <6220000 38092800>;
+		};
+
+		cpu7_opp6: opp-1862400000 {
+			opp-hz = /bits/ 64 <1862400000>;
+			opp-peak-kBps = <6220000 38092800>;
+		};
+
+		cpu7_opp7: opp-2035200000 {
+			opp-hz = /bits/ 64 <2035200000>;
+			opp-peak-kBps = <6220000 38092800>;
+		};
+
+		cpu7_opp8: opp-2112000000 {
+			opp-hz = /bits/ 64 <2112000000>;
+			opp-peak-kBps = <6220000 44851200>;
+		};
+
+		cpu7_opp9: opp-2208000000 {
+			opp-hz = /bits/ 64 <2208000000>;
+			opp-peak-kBps = <6220000 44851200>;
+		};
+
+		cpu7_opp10: opp-2380800000 {
+			opp-hz = /bits/ 64 <2380800000>;
+			opp-peak-kBps = <6832000 44851200>;
+		};
+
+		cpu7_opp11: opp-2400000000 {
+			opp-hz = /bits/ 64 <2400000000>;
+			opp-peak-kBps = <8532000 48537600>;
+		};
+
+		cpu7_opp12: opp-2515200000 {
+			opp-hz = /bits/ 64 <2515200000>;
+			opp-peak-kBps = <8532000 48537600>;
+		};
+
+		cpu7_opp13: opp-2707200000 {
+			opp-hz = /bits/ 64 <2707200000>;
+			opp-peak-kBps = <8532000 48537600>;
+		};
+	};
+
 	memory@80000000 {
 		device_type = "memory";
 		/* We expect the bootloader to fill in the size */
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Reviewed-by on v2 2/2
#4 lore raw

Re: [PATCH v2 2/2] arm64: dts: qcom: sc7280: Add cpu OPP tables

Hi,

arch/arm64/boot/dts/qcom/sc7280.dtsi line 280

Quoted 6 lines · Sibi Sankar
arch/arm64/boot/dts/qcom/sc7280.dtsi +5 -0
+       cpu0_opp_table: cpu0_opp_table {
+               compatible = "operating-points-v2";
+               opp-shared;
+
+               cpu0_opp1: opp-300000000 {

It seems like it might be nicer to give the node labels a less arbitrary name. How about?

cpu0_opp_300mhz: opp-300000000

That has advantes:

* If, for some reason, you have to mess with some operating point in another dts it'll be less fragile.

* It'll make diffing easier between SoCs.

* If you end up putting a new operating point in the middle you don't need to rename everything below.

Other than that, I can't say that I'm a huge expert on the interconnect stuff and whether those make sense, but I'm still OK with:

Reviewed-by Douglas Anderson <[email protected]>
author
#5 lore raw

Re: [PATCH v2 2/2] arm64: dts: qcom: sc7280: Add cpu OPP tables

Hey Doug,

Thanks for the review!

Quoted 17 lines · Doug Anderson

Hi,

arch/arm64/boot/dts/qcom/sc7280.dtsi line 280

Quoted 6 lines · Sibi Sankar
arch/arm64/boot/dts/qcom/sc7280.dtsi +5 -0
+       cpu0_opp_table: cpu0_opp_table {
+               compatible = "operating-points-v2";
+               opp-shared;
+
+               cpu0_opp1: opp-300000000 {

It seems like it might be nicer to give the node labels a less arbitrary name. How about?

cpu0_opp_300mhz: opp-300000000

That has advantes:

Quoted 7 lines

* If, for some reason, you have to mess with some operating point in another dts it'll be less fragile.

* It'll make diffing easier between SoCs.

* If you end up putting a new operating point in the middle you don't need to rename everything below.

sure makes sense, will fix it in v3.

Quoted 6 lines

Other than that, I can't say that I'm a huge expert on the interconnect stuff and whether those make sense, but I'm still OK with:

Reviewed-by Douglas Anderson <[email protected]>
Signature · 2 lines
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.