mfd: rt4831: Adds support for Richtek RT4831

index 5c7f2b1..49e57c9 100644
@@ -1076,6 +1076,16 @@ config MFD_RDC321X
 	  southbridge which provides access to GPIOs and Watchdog using the
 	  southbridge PCI device configuration space.
 
+config MFD_RT4831
+	tristate "Richtek RT4831 four channel WLED and Display Bias Voltage"
+	depends on I2C
+	select MFD_CORE
+	select REGMAP_I2C
+	help
+	  This enables support for the Richtek RT4831 that includes 4 channel
+	  WLED driving and Display Bias Voltage. It's commonly used to provide
+	  power to the LCD display and LCD backlight.
+
 config MFD_RT5033
 	tristate "Richtek RT5033 Power Management IC"
 	depends on I2C

index 4f6d2b8..eb42bd4 100644
@@ -234,6 +234,7 @@ obj-$(CONFIG_MFD_MENF21BMC)	+= menf21bmc.o
 obj-$(CONFIG_MFD_HI6421_PMIC)	+= hi6421-pmic-core.o
 obj-$(CONFIG_MFD_HI655X_PMIC)   += hi655x-pmic.o
 obj-$(CONFIG_MFD_DLN2)		+= dln2.o
+obj-$(CONFIG_MFD_RT4831)	+= rt4831.o
 obj-$(CONFIG_MFD_RT5033)	+= rt5033.o
 obj-$(CONFIG_MFD_SKY81452)	+= sky81452.o
 

new file mode 100644
index 00000000..e0ac686
@@ -0,0 +1,62 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/backlight/richtek,rt4831-backlight.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Richtek RT4831 Backlight
+
+maintainers:
+  - ChiYuan Huang <[email protected]>
+
+description: |
+  RT4831 is a mutifunctional device that can provide power to the LCD display
+  and LCD backlight.
+
+  For the LCD backlight, it can provide four channel WLED driving capability.
+  Each channel driving current is up to 30mA
+
+  Datasheet is available at
+  https://www.richtek.com/assets/product_file/RT4831A/DS4831A-05.pdf
+
+allOf:
+  - $ref: common.yaml#
+
+properties:
+  compatible:
+    const: richtek,rt4831-backlight
+
+  default-brightness:
+    minimum: 0
+    maximum: 2048
+
+  max-brightness:
+    minimum: 0
+    maximum: 2048
+
+  richtek,pwm-enable:
+    description: |
+      Specify the backlight dimming following by PWM duty or by SW control.
+    type: boolean
+
+  richtek,bled-ovp-sel:
+    description: |
+      Backlight OVP level selection, currently support 17V/21V/25V/29V.
+    $ref: /schemas/types.yaml#/definitions/uint8
+    default: 1
+    minimum: 0
+    maximum: 3
+
+  richtek,channel-use:
+    description: |
+      Backlight LED channel to be used.
+      BIT 0/1/2/3 is used to indicate led channel 1/2/3/4 enable or disable.
+    $ref: /schemas/types.yaml#/definitions/uint8
+    minimum: 1
+    maximum: 15
+
+required:
+  - compatible
+  - richtek,channel-use
+
+additionalProperties: false

new file mode 100644
index 00000000..4762eb1
@@ -0,0 +1,90 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/richtek,rt4831.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Richtek RT4831 DSV and Backlight Integrated IC
+
+maintainers:
+  - ChiYuan Huang <[email protected]>
+
+description: |
+  RT4831 is a multifunctional device that can provide power to the LCD display
+  and LCD backlight.
+
+  For Display Bias Voltage DSVP and DSVN, the output range is about 4V to 6.5V.
+  It's sufficient to meet the current LCD power requirement.
+
+  For the LCD backlight, it can provide four channel WLED driving capability.
+  Each channel driving current is up to 30mA
+
+  Datasheet is available at
+  https://www.richtek.com/assets/product_file/RT4831A/DS4831A-05.pdf
+
+properties:
+  compatible:
+    const: richtek,rt4831
+
+  reg:
+    description: I2C device address.
+    maxItems: 1
+
+  enable-gpios:
+    description: |
+      GPIO to enable/disable the chip. It is optional.
+      Some usage directly tied this pin to follow VIO 1.8V power on sequence.
+    maxItems: 1
+
+  regulators:
+    $ref: ../regulator/richtek,rt4831-regulator.yaml
+
+  backlight:
+    $ref: ../leds/backlight/richtek,rt4831-backlight.yaml
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/leds/rt4831-backlight.h>
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      rt4831@11 {
+        compatible = "richtek,rt4831";
+        reg = <0x11>;
+
+        regulators {
+          DSVLCM {
+            regulator-min-microvolt = <4000000>;
+            regulator-max-microvolt = <7150000>;
+            regulator-allow-bypass;
+          };
+          DSVP {
+            regulator-name = "rt4831-dsvp";
+            regulator-min-microvolt = <4000000>;
+            regulator-max-microvolt = <6500000>;
+            regulator-boot-on;
+          };
+          DSVN {
+            regulator-name = "rt4831-dsvn";
+            regulator-min-microvolt = <4000000>;
+            regulator-max-microvolt = <6500000>;
+            regulator-boot-on;
+          };
+        };
+
+        backlight {
+          compatible = "richtek,rt4831-backlight";
+          default-brightness = <1024>;
+          max-brightness = <2048>;
+          richtek,bled-ovp-sel = /bits/ 8 <RT4831_BLOVPLVL_21V>;
+          richtek,channel-use = /bits/ 8 <RT4831_BLED_ALLCHEN>;
+        };
+      };
+    };

index d83c87b..858f6df 100644
@@ -289,6 +289,14 @@ config BACKLIGHT_QCOM_WLED
 	  If you have the Qualcomm PMIC, say Y to enable a driver for the
 	  WLED block. Currently it supports PM8941 and PMI8998.
 
+config BACKLIGHT_RT4831
+	tristate "Richtek RT4831 Backlight Driver"
+	depends on MFD_RT4831
+	help
+	  This enables support for Richtek RT4831 Backlight driver.
+	  It's commonly used to drive the display WLED. There're four channels
+	  inisde, and each channel can provide up to 30mA current.
+
 config BACKLIGHT_SAHARA
 	tristate "Tabletkiosk Sahara Touch-iT Backlight Driver"
 	depends on X86

index 685f3f1..cae2c83 100644
@@ -49,6 +49,7 @@ obj-$(CONFIG_BACKLIGHT_PANDORA)		+= pandora_bl.o
 obj-$(CONFIG_BACKLIGHT_PCF50633)	+= pcf50633-backlight.o
 obj-$(CONFIG_BACKLIGHT_PWM)		+= pwm_bl.o
 obj-$(CONFIG_BACKLIGHT_QCOM_WLED)	+= qcom-wled.o
+obj-$(CONFIG_BACKLIGHT_RT4831)		+= rt4831-backlight.o
 obj-$(CONFIG_BACKLIGHT_SAHARA)		+= kb3886_bl.o
 obj-$(CONFIG_BACKLIGHT_SKY81452)	+= sky81452-backlight.o
 obj-$(CONFIG_BACKLIGHT_TOSA)		+= tosa_bl.o