AM64: EVM/SK: Enable PCIe and USB
v2 cover AM64: EVM/SK: Enable PCIe and USB
AM642 EVM has one PCIe slot (no USB slot) and AM642 SK has one USB slot (no PCIe slot).
AM64 SoC has one SERDES module which can be used by either PCIe or USB.
Add DT nodes to represent and enable SERDES/PCIe/USB modules in EVM/SK.
Changes from v1:
1) Add a patch to convert reg-mux DT bindings to YAML
2) Use generic names for clock node names
3) Remove redundant status = "okay" for serdes_wiz0
Kishon Vijay Abraham I (6):
dt-bindings: mux: Convert reg-mux DT bindings to YAML
arm64: dts: ti: k3-am64-main: Add SERDES DT node
arm64: dts: ti: k3-am64-main: Add PCIe DT node
arm64: dts: ti: k3-am642-evm: Enable PCIe and SERDES
arm64: dts: ti: k3-am642-sk: Enable USB Super-Speed HOST port
arm64: dts: ti: k3-am642-sk: Disable PCIe
.../bindings/mux/mux-controller.txt | 113 ++++++++++++++- .../devicetree/bindings/mux/reg-mux.txt | 129 ------------------ .../devicetree/bindings/mux/reg-mux.yaml | 47 +++++++ arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 102 ++++++++++++++ arch/arm64/boot/dts/ti/k3-am642-evm.dts | 30 ++++ arch/arm64/boot/dts/ti/k3-am642-sk.dts | 43 ++++++ 6 files changed, 334 insertions(+), 130 deletions(-) delete mode 100644 Documentation/devicetree/bindings/mux/reg-mux.txt create mode 100644 Documentation/devicetree/bindings/mux/reg-mux.yaml
Signature · 1 line
2.17.1
PATCH v2 1/6 dt-bindings: mux: Convert reg-mux DT bindings to YAML
Convert reg-mux DT bindings to YAML. Move the examples provided in reg-mux.txt to mux-controller.txt and remove reg-mux.txt
--- .../bindings/mux/mux-controller.txt | 113 ++++++++++++++- .../devicetree/bindings/mux/reg-mux.txt | 129 ------------------ .../devicetree/bindings/mux/reg-mux.yaml | 47 +++++++ 3 files changed, 159 insertions(+), 130 deletions(-) delete mode 100644 Documentation/devicetree/bindings/mux/reg-mux.txt create mode 100644 Documentation/devicetree/bindings/mux/reg-mux.yaml
Documentation/devicetree/bindings/mux/mux-controller.txt +112 -1
@@ -38,7 +38,7 @@ mux-ctrl-specifier typically encodes the chip-relative mux controller number. If the mux controller chip only provides a single mux controller, the mux-ctrl-specifier can typically be left out. -Example: +Example 1: /* One consumer of a 2-way mux controller (one GPIO-line) */ mux: mux-controller {
@@ -64,6 +64,8 @@ because there is only one mux controller in the list. However, if the driver for the consumer node in fact asks for a named mux controller, that name is of course still required. +Example 2: + /* * Two consumers (one for an ADC line and one for an i2c bus) of * parallel 4-way multiplexers controlled by the same two GPIO-lines.
@@ -116,6 +118,115 @@ course still required. }; }; +Example 3: + +The parent device of mux controller is not a syscon device. + +&i2c0 { + fpga@66 { // fpga connected to i2c + compatible = "fsl,lx2160aqds-fpga", "fsl,fpga-qixis-i2c", + "simple-mfd"; + reg = <0x66>; + + mux: mux-controller { + compatible = "reg-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x54 0xf8>, /* 0: reg 0x54, bits 7:3 */ + <0x54 0x07>; /* 1: reg 0x54, bits 2:0 */ + }; + }; +}; + +mdio-mux-1 { + compatible = "mdio-mux-multiplexer"; + mux-controls = <&mux 0>; + mdio-parent-bus = <&emdio1>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + mdio@8 { + reg = <0x8>; + #address-cells = <1>; + #size-cells = <0>; + }; + + .. + .. +}; + +mdio-mux-2 { + compatible = "mdio-mux-multiplexer"; + mux-controls = <&mux 1>; + mdio-parent-bus = <&emdio2>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + mdio@1 { + reg = <0x1>; + #address-cells = <1>; + #size-cells = <0>; + }; + + .. + .. +}; + +Example 4: + +The parent device of mux controller is syscon device. + +syscon { + compatible = "syscon"; + + mux: mux-controller { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + + mux-reg-masks = <0x3 0x30>, /* 0: reg 0x3, bits 5:4 */ + <0x3 0x40>, /* 1: reg 0x3, bit 6 */ + idle-states = <MUX_IDLE_AS_IS>, <0>; + }; +}; + +video-mux { + compatible = "video-mux"; + mux-controls = <&mux 0>; + #address-cells = <1>; + #size-cells = <0>; + + ports { + /* inputs 0..3 */ + port@0 { + reg = <0>; + }; + port@1 { + reg = <1>; + }; + port@2 { + reg = <2>; + }; + port@3 { + reg = <3>; + }; + + /* output */ + port@4 { + reg = <4>; + }; + }; +}; Mux controller nodes --------------------
Documentation/devicetree/bindings/mux/reg-mux.txt deleted +0 -129
129 lines not on this page · raw message
Documentation/devicetree/bindings/mux/reg-mux.yaml new file +47 -0
47 lines not on this page · raw message
Signature · 1 line
2.17.1
Nishanth Menon
maintainerRe: [PATCH v2 1/6] dt-bindings: mux: Convert reg-mux DT bindings to YAML
Quoted 2 lines · Kishon Vijay Abraham I
Convert reg-mux DT bindings to YAML. Move the examples provided in reg-mux.txt to mux-controller.txt and remove reg-mux.txt
--to 'Rob Herring <[email protected]>' --to 'Peter Rosin <[email protected]>' please.
If Peter and Rob request me, then I can pick into my tree..
Quoted 339 lines
Signed-off-by Kishon Vijay Abraham I <[email protected]>--- .../bindings/mux/mux-controller.txt | 113 ++++++++++++++- .../devicetree/bindings/mux/reg-mux.txt | 129 ------------------ .../devicetree/bindings/mux/reg-mux.yaml | 47 +++++++ 3 files changed, 159 insertions(+), 130 deletions(-) delete mode 100644 Documentation/devicetree/bindings/mux/reg-mux.txt create mode 100644 Documentation/devicetree/bindings/mux/reg-mux.yamlDocumentation/devicetree/bindings/mux/mux-controller.txt +112
-1@@ -38,7 +38,7 @@ mux-ctrl-specifier typically encodes the chip-relative mux controller number. If the mux controller chip only provides a single mux controller, the mux-ctrl-specifier can typically be left out. -Example: +Example 1: /* One consumer of a 2-way mux controller (one GPIO-line) */ mux: mux-controller {@@ -64,6 +64,8 @@ because there is only one mux controller in the list. However, if the driver for the consumer node in fact asks for a named mux controller, that name is of course still required. +Example 2: + /* * Two consumers (one for an ADC line and one for an i2c bus) of * parallel 4-way multiplexers controlled by the same two GPIO-lines.@@ -116,6 +118,115 @@ course still required. }; }; +Example 3: + +The parent device of mux controller is not a syscon device. + +&i2c0 { + fpga@66 { // fpga connected to i2c + compatible = "fsl,lx2160aqds-fpga", "fsl,fpga-qixis-i2c", + "simple-mfd"; + reg = <0x66>; + + mux: mux-controller { + compatible = "reg-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x54 0xf8>, /* 0: reg 0x54, bits 7:3 */ + <0x54 0x07>; /* 1: reg 0x54, bits 2:0 */ + }; + }; +}; + +mdio-mux-1 { + compatible = "mdio-mux-multiplexer"; + mux-controls = <&mux 0>; + mdio-parent-bus = <&emdio1>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + mdio@8 { + reg = <0x8>; + #address-cells = <1>; + #size-cells = <0>; + }; + + .. + .. +}; + +mdio-mux-2 { + compatible = "mdio-mux-multiplexer"; + mux-controls = <&mux 1>; + mdio-parent-bus = <&emdio2>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + mdio@1 { + reg = <0x1>; + #address-cells = <1>; + #size-cells = <0>; + }; + + .. + .. +}; + +Example 4: + +The parent device of mux controller is syscon device. + +syscon { + compatible = "syscon"; + + mux: mux-controller { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + + mux-reg-masks = <0x3 0x30>, /* 0: reg 0x3, bits 5:4 */ + <0x3 0x40>, /* 1: reg 0x3, bit 6 */ + idle-states = <MUX_IDLE_AS_IS>, <0>; + }; +}; + +video-mux { + compatible = "video-mux"; + mux-controls = <&mux 0>; + #address-cells = <1>; + #size-cells = <0>; + + ports { + /* inputs 0..3 */ + port@0 { + reg = <0>; + }; + port@1 { + reg = <1>; + }; + port@2 { + reg = <2>; + }; + port@3 { + reg = <3>; + }; + + /* output */ + port@4 { + reg = <4>; + }; + }; +}; Mux controller nodes --------------------Documentation/devicetree/bindings/mux/reg-mux.txt deleted +0
-129@@ -1,129 +0,0 @@ -Generic register bitfield-based multiplexer controller bindings - -Define register bitfields to be used to control multiplexers. The parent -device tree node must be a device node to provide register r/w access. - -Required properties: -- compatible : should be one of - "reg-mux" : if parent device of mux controller is not syscon device - "mmio-mux" : if parent device of mux controller is syscon device -- #mux-control-cells : <1> -- mux-reg-masks : an array of register offset and pre-shifted bitfield mask - pairs, each describing a single mux control. -* Standard mux-controller bindings as decribed in mux-controller.txt - -Optional properties: -- idle-states : if present, the state the muxes will have when idle. The - special state MUX_IDLE_AS_IS is the default. - -The multiplexer state of each multiplexer is defined as the value of the -bitfield described by the corresponding register offset and bitfield mask -pair in the mux-reg-masks array. - -Example 1: -The parent device of mux controller is not a syscon device. - -&i2c0 { - fpga@66 { // fpga connected to i2c - compatible = "fsl,lx2160aqds-fpga", "fsl,fpga-qixis-i2c", - "simple-mfd"; - reg = <0x66>; - - mux: mux-controller { - compatible = "reg-mux"; - #mux-control-cells = <1>; - mux-reg-masks = <0x54 0xf8>, /* 0: reg 0x54, bits 7:3 */ - <0x54 0x07>; /* 1: reg 0x54, bits 2:0 */ - }; - }; -}; - -mdio-mux-1 { - compatible = "mdio-mux-multiplexer"; - mux-controls = <&mux 0>; - mdio-parent-bus = <&emdio1>; - #address-cells = <1>; - #size-cells = <0>; - - mdio@0 { - reg = <0x0>; - #address-cells = <1>; - #size-cells = <0>; - }; - - mdio@8 { - reg = <0x8>; - #address-cells = <1>; - #size-cells = <0>; - }; - - .. - .. -}; - -mdio-mux-2 { - compatible = "mdio-mux-multiplexer"; - mux-controls = <&mux 1>; - mdio-parent-bus = <&emdio2>; - #address-cells = <1>; - #size-cells = <0>; - - mdio@0 { - reg = <0x0>; - #address-cells = <1>; - #size-cells = <0>; - }; - - mdio@1 { - reg = <0x1>; - #address-cells = <1>; - #size-cells = <0>; - }; - - .. - .. -}; - -Example 2: -The parent device of mux controller is syscon device. - -syscon { - compatible = "syscon"; - - mux: mux-controller { - compatible = "mmio-mux"; - #mux-control-cells = <1>; - - mux-reg-masks = <0x3 0x30>, /* 0: reg 0x3, bits 5:4 */ - <0x3 0x40>, /* 1: reg 0x3, bit 6 */ - idle-states = <MUX_IDLE_AS_IS>, <0>; - }; -}; - -video-mux { - compatible = "video-mux"; - mux-controls = <&mux 0>; - #address-cells = <1>; - #size-cells = <0>; - - ports { - /* inputs 0..3 */ - port@0 { - reg = <0>; - }; - port@1 { - reg = <1>; - }; - port@2 { - reg = <2>; - }; - port@3 { - reg = <3>; - }; - - /* output */ - port@4 { - reg = <4>; - }; - }; -};Documentation/devicetree/bindings/mux/reg-mux.yaml new file +47
-0@@ -0,0 +1,47 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/mux/reg-mux.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Generic register bitfield-based multiplexer controller bindings + +maintainers: + - Peter Rosin <[email protected]> + +properties: + compatible: + enum: + - reg-mux + - mmio-mux + + "#mux-control-cells": true + + mux-reg-masks: + minItems: 2 + maxItems: 32 + description: + An array of register offset and pre-shifted bitfield mask pairs, each describing a + single mux control. + + idle-states: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + +required: + - compatible + - mux-reg-masks + +additionalProperties: false + +examples: + - | + serdes_ln_ctrl: mux { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1 select */ + <0x4090 0x3>, <0x4094 0x3>, /* SERDES1 lane0/1 select */ + <0x40a0 0x3>, <0x40a4 0x3>, /* SERDES2 lane0/1 select */ + <0x40b0 0x3>, <0x40b4 0x3>, /* SERDES3 lane0/1 select */ + <0x40c0 0x3>, <0x40c4 0x3>, <0x40c8 0x3>, <0x40cc 0x3>; + };Signature · 1 line
2.17.1
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Re: [PATCH v2 1/6] dt-bindings: mux: Convert reg-mux DT bindings to YAML
Hi!
Quoted 9 lines · Nishanth Menon
Quoted 2 lines · Kishon Vijay Abraham I
Convert reg-mux DT bindings to YAML. Move the examples provided in reg-mux.txt to mux-controller.txt and remove reg-mux.txt
--to 'Rob Herring <[email protected]>' --to 'Peter Rosin <[email protected]>' please.
If Peter and Rob request me, then I can pick into my tree..
It would make more sense to me to convert the common mux controller node bindings in mux-controller.txt to yaml first, and only then convert the reg-mux bindings. I.e. duplicating some of the info common to all muxes from mux-contoller.txt in reg-mux.yaml looks like a failure to me. I understand that as long as not all bindings are converted to yaml in one go, there will be some duplicate information, but in this case info that is common to all muxes are moved into the "leaf" binding and will result in duplication once more mux bindings are converted.
But I don't know the yaml rules, so I might easily just not get it. I have some other questions below...
Quoted 300 lines
Quoted 300 lines
Signed-off-by Kishon Vijay Abraham I <[email protected]>--- .../bindings/mux/mux-controller.txt | 113 ++++++++++++++- .../devicetree/bindings/mux/reg-mux.txt | 129 ------------------ .../devicetree/bindings/mux/reg-mux.yaml | 47 +++++++ 3 files changed, 159 insertions(+), 130 deletions(-) delete mode 100644 Documentation/devicetree/bindings/mux/reg-mux.txt create mode 100644 Documentation/devicetree/bindings/mux/reg-mux.yamlDocumentation/devicetree/bindings/mux/mux-controller.txt +112
-1@@ -38,7 +38,7 @@ mux-ctrl-specifier typically encodes the chip-relative mux controller number. If the mux controller chip only provides a single mux controller, the mux-ctrl-specifier can typically be left out. -Example: +Example 1: /* One consumer of a 2-way mux controller (one GPIO-line) */ mux: mux-controller {@@ -64,6 +64,8 @@ because there is only one mux controller in the list. However, if the driver for the consumer node in fact asks for a named mux controller, that name is of course still required. +Example 2: + /* * Two consumers (one for an ADC line and one for an i2c bus) of * parallel 4-way multiplexers controlled by the same two GPIO-lines.@@ -116,6 +118,115 @@ course still required. }; }; +Example 3: + +The parent device of mux controller is not a syscon device. + +&i2c0 { + fpga@66 { // fpga connected to i2c + compatible = "fsl,lx2160aqds-fpga", "fsl,fpga-qixis-i2c", + "simple-mfd"; + reg = <0x66>; + + mux: mux-controller { + compatible = "reg-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x54 0xf8>, /* 0: reg 0x54, bits 7:3 */ + <0x54 0x07>; /* 1: reg 0x54, bits 2:0 */ + }; + }; +}; + +mdio-mux-1 { + compatible = "mdio-mux-multiplexer"; + mux-controls = <&mux 0>; + mdio-parent-bus = <&emdio1>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + mdio@8 { + reg = <0x8>; + #address-cells = <1>; + #size-cells = <0>; + }; + + .. + .. +}; + +mdio-mux-2 { + compatible = "mdio-mux-multiplexer"; + mux-controls = <&mux 1>; + mdio-parent-bus = <&emdio2>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + mdio@1 { + reg = <0x1>; + #address-cells = <1>; + #size-cells = <0>; + }; + + .. + .. +}; + +Example 4: + +The parent device of mux controller is syscon device. + +syscon { + compatible = "syscon"; + + mux: mux-controller { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + + mux-reg-masks = <0x3 0x30>, /* 0: reg 0x3, bits 5:4 */ + <0x3 0x40>, /* 1: reg 0x3, bit 6 */ + idle-states = <MUX_IDLE_AS_IS>, <0>; + }; +}; + +video-mux { + compatible = "video-mux"; + mux-controls = <&mux 0>; + #address-cells = <1>; + #size-cells = <0>; + + ports { + /* inputs 0..3 */ + port@0 { + reg = <0>; + }; + port@1 { + reg = <1>; + }; + port@2 { + reg = <2>; + }; + port@3 { + reg = <3>; + }; + + /* output */ + port@4 { + reg = <4>; + }; + }; +}; Mux controller nodes --------------------Documentation/devicetree/bindings/mux/reg-mux.txt deleted +0
-129@@ -1,129 +0,0 @@ -Generic register bitfield-based multiplexer controller bindings - -Define register bitfields to be used to control multiplexers. The parent -device tree node must be a device node to provide register r/w access. - -Required properties: -- compatible : should be one of - "reg-mux" : if parent device of mux controller is not syscon device - "mmio-mux" : if parent device of mux controller is syscon device -- #mux-control-cells : <1> -- mux-reg-masks : an array of register offset and pre-shifted bitfield mask - pairs, each describing a single mux control. -* Standard mux-controller bindings as decribed in mux-controller.txt - -Optional properties: -- idle-states : if present, the state the muxes will have when idle. The - special state MUX_IDLE_AS_IS is the default. - -The multiplexer state of each multiplexer is defined as the value of the -bitfield described by the corresponding register offset and bitfield mask -pair in the mux-reg-masks array. - -Example 1: -The parent device of mux controller is not a syscon device. - -&i2c0 { - fpga@66 { // fpga connected to i2c - compatible = "fsl,lx2160aqds-fpga", "fsl,fpga-qixis-i2c", - "simple-mfd"; - reg = <0x66>; - - mux: mux-controller { - compatible = "reg-mux"; - #mux-control-cells = <1>; - mux-reg-masks = <0x54 0xf8>, /* 0: reg 0x54, bits 7:3 */ - <0x54 0x07>; /* 1: reg 0x54, bits 2:0 */ - }; - }; -}; - -mdio-mux-1 { - compatible = "mdio-mux-multiplexer"; - mux-controls = <&mux 0>; - mdio-parent-bus = <&emdio1>; - #address-cells = <1>; - #size-cells = <0>; - - mdio@0 { - reg = <0x0>; - #address-cells = <1>; - #size-cells = <0>; - }; - - mdio@8 { - reg = <0x8>; - #address-cells = <1>; - #size-cells = <0>; - }; - - .. - .. -}; - -mdio-mux-2 { - compatible = "mdio-mux-multiplexer"; - mux-controls = <&mux 1>; - mdio-parent-bus = <&emdio2>; - #address-cells = <1>; - #size-cells = <0>; - - mdio@0 { - reg = <0x0>; - #address-cells = <1>; - #size-cells = <0>; - }; - - mdio@1 { - reg = <0x1>; - #address-cells = <1>; - #size-cells = <0>; - }; - - .. - .. -}; - -Example 2: -The parent device of mux controller is syscon device. - -syscon { - compatible = "syscon"; - - mux: mux-controller { - compatible = "mmio-mux"; - #mux-control-cells = <1>; - - mux-reg-masks = <0x3 0x30>, /* 0: reg 0x3, bits 5:4 */ - <0x3 0x40>, /* 1: reg 0x3, bit 6 */ - idle-states = <MUX_IDLE_AS_IS>, <0>; - }; -}; - -video-mux { - compatible = "video-mux"; - mux-controls = <&mux 0>; - #address-cells = <1>; - #size-cells = <0>; - - ports { - /* inputs 0..3 */ - port@0 { - reg = <0>; - }; - port@1 { - reg = <1>; - }; - port@2 { - reg = <2>; - }; - port@3 { - reg = <3>; - }; - - /* output */ - port@4 { - reg = <4>; - }; - }; -};Documentation/devicetree/bindings/mux/reg-mux.yaml new file +10
-0@@ -0,0 +1,47 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/mux/reg-mux.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Generic register bitfield-based multiplexer controller bindings + +maintainers: + - Peter Rosin <[email protected]>
Quoted 8 lines
Documentation/devicetree/bindings/mux/reg-mux.yaml line 18
Quoted 8 lines
Documentation/devicetree/bindings/mux/reg-mux.yaml new file +8
-0+ +properties: + compatible: + enum: + - reg-mux + - mmio-mux + + "#mux-control-cells": true
true? It has to be exactly 1 for this binding. Is that enforced somewhere?
Quoted 7 lines
Documentation/devicetree/bindings/mux/reg-mux.yaml line 25
Quoted 7 lines
Documentation/devicetree/bindings/mux/reg-mux.yaml new file +7
-0+ + mux-reg-masks: + minItems: 2 + maxItems: 32 + description: + An array of register offset and pre-shifted bitfield mask pairs, each describing a + single mux control.
Is there a way to specify that it has to be an even number of items?
Cheers,
Peter
Quoted 26 lines
Quoted 25 lines
Documentation/devicetree/bindings/mux/reg-mux.yaml new file +22
-0+ + idle-states: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + +required: + - compatible + - mux-reg-masks + +additionalProperties: false + +examples: + - | + serdes_ln_ctrl: mux { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1 select */ + <0x4090 0x3>, <0x4094 0x3>, /* SERDES1 lane0/1 select */ + <0x40a0 0x3>, <0x40a4 0x3>, /* SERDES2 lane0/1 select */ + <0x40b0 0x3>, <0x40b4 0x3>, /* SERDES3 lane0/1 select */ + <0x40c0 0x3>, <0x40c4 0x3>, <0x40c8 0x3>, <0x40cc 0x3>; + };Signature · 1 line
2.17.1
Rob Herring
maintainerRe: [PATCH v2 1/6] dt-bindings: mux: Convert reg-mux DT bindings to YAML
In reply to Kishon Vijay Abraham IQuoted 12 lines · Kishon Vijay Abraham I
Convert reg-mux DT bindings to YAML. Move the examples provided in reg-mux.txt to mux-controller.txt and remove reg-mux.txt
Signed-off-by Kishon Vijay Abraham I <[email protected]>--- .../bindings/mux/mux-controller.txt | 113 ++++++++++++++- .../devicetree/bindings/mux/reg-mux.txt | 129 ------------------ .../devicetree/bindings/mux/reg-mux.yaml | 47 +++++++ 3 files changed, 159 insertions(+), 130 deletions(-) delete mode 100644 Documentation/devicetree/bindings/mux/reg-mux.txt create mode 100644 Documentation/devicetree/bindings/mux/reg-mux.yaml
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.example.dt.yaml: serdes-ln-ctrl@4080: 'mux-reg-masks' is a required property
From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/mux/reg-mux.yaml
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.example.dt.yaml: serdes-ln-ctrl@4080: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+'
From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/mux/reg-mux.yaml
See https://patchwork.ozlabs.org/patch/1479231
This check can fail if there are any dependencies. The base for a patch series is generally the most recent rc1.
If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date:
pip3 install dtschema --upgrade
Please check and re-submit.
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Rob Herring
maintainerRe: [PATCH v2 1/6] dt-bindings: mux: Convert reg-mux DT bindings to YAML
In reply to Kishon Vijay Abraham IQuoted 6 lines · Kishon Vijay Abraham I
Convert reg-mux DT bindings to YAML. Move the examples provided in reg-mux.txt to mux-controller.txt and remove reg-mux.txt
Signed-off-by Kishon Vijay Abraham I <[email protected]>--- .../bindings/mux/mux-controller.txt | 113 ++++++++++++++-
We don't want to be adding to this.
Quoted 5 lines
.../devicetree/bindings/mux/reg-mux.txt | 129 ------------------ .../devicetree/bindings/mux/reg-mux.yaml | 47 +++++++ 3 files changed, 159 insertions(+), 130 deletions(-) delete mode 100644 Documentation/devicetree/bindings/mux/reg-mux.txt create mode 100644 Documentation/devicetree/bindings/mux/reg-mux.yaml
I have a more complete series converting mux bindings I'll send out.
Rob
PATCH v2 2/6 arm64: dts: ti: k3-am64-main: Add SERDES DT node
In reply to Kishon Vijay Abraham IAM64 has one SERDES 10G instance. Add SERDES DT node for it.
--- arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 56 ++++++++++++++++++++++++ 1 file changed, 56 insertions(+)
arch/arm64/boot/dts/ti/k3-am64-main.dtsi +56 -0
@@ -5,6 +5,17 @@ * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/ */ +#include <dt-bindings/phy/phy-cadence.h> +#include <dt-bindings/phy/phy-ti.h> + +/ { + serdes_refclk: clock { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <0>; + }; +}; + &cbass_main { oc_sram: sram@70000000 { compatible = "mmio-sram";
@@ -18,6 +29,20 @@ }; }; + main_conf: syscon@43000000 { + compatible = "ti,j721e-system-controller", "syscon", "simple-mfd"; + reg = <0x0 0x43000000 0x0 0x20000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x43000000 0x20000>; + + serdes_ln_ctrl: mux { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x4080 0x3>; /* SERDES0 lane0 select */ + }; + }; + gic500: interrupt-controller@1800000 { compatible = "arm,gic-v3"; #address-cells = <2>;
@@ -672,4 +697,35 @@ ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; }; + + serdes_wiz0: wiz@f000000 { + compatible = "ti,am64-wiz-10g"; + #address-cells = <1>; + #size-cells = <1>; + power-domains = <&k3_pds 162 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 162 0>, <&k3_clks 162 1>, <&serdes_refclk>; + clock-names = "fck", "core_ref_clk", "ext_ref_clk"; + num-lanes = <1>; + #reset-cells = <1>; + #clock-cells = <1>; + ranges = <0x0f000000 0x0 0x0f000000 0x00010000>; + + assigned-clocks = <&k3_clks 162 1>; + assigned-clock-parents = <&k3_clks 162 5>; + + serdes0: serdes@f000000 { + compatible = "ti,j721e-serdes-10g"; + reg = <0x0f000000 0x00010000>; + reg-names = "torrent_phy"; + resets = <&serdes_wiz0 0>; + reset-names = "torrent_reset"; + clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>, <&serdes_wiz0 TI_WIZ_PHY_EN_REFCLK>; + clock-names = "refclk", "phy_en_refclk"; + assigned-clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>, <&serdes_wiz0 TI_WIZ_PLL1_REFCLK>, <&serdes_wiz0 TI_WIZ_REFCLK_DIG>; + assigned-clock-parents = <&k3_clks 162 1>, <&k3_clks 162 1>, <&k3_clks 162 1>; + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <1>; + }; + }; };
Signature · 1 line
2.17.1
PATCH v2 3/6 arm64: dts: ti: k3-am64-main: Add PCIe DT node
In reply to Kishon Vijay Abraham IAM64 has one PCIe instance which can be configured in either host mode (RC) or device mode (EP). Add PCIe DT node for host mode and device mode here.
--- arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 46 ++++++++++++++++++++++++ 1 file changed, 46 insertions(+)
arch/arm64/boot/dts/ti/k3-am64-main.dtsi +46 -0
@@ -728,4 +728,50 @@ #clock-cells = <1>; }; }; + + pcie0_rc: pcie@f102000 { + compatible = "ti,am64-pcie-host", "ti,j721e-pcie-host"; + reg = <0x00 0x0f102000 0x00 0x1000>, + <0x00 0x0f100000 0x00 0x400>, + <0x00 0x0d000000 0x00 0x00800000>, + <0x00 0x68000000 0x00 0x00001000>; + reg-names = "intd_cfg", "user_cfg", "reg", "cfg"; + interrupt-names = "link_state"; + interrupts = <GIC_SPI 203 IRQ_TYPE_EDGE_RISING>; + device_type = "pci"; + ti,syscon-pcie-ctrl = <&main_conf 0x4070>; + max-link-speed = <2>; + num-lanes = <1>; + power-domains = <&k3_pds 114 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 114 0>, <&serdes0 CDNS_TORRENT_REFCLK_DRIVER>; + clock-names = "fck", "pcie_refclk"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x0 0xff>; + cdns,no-bar-match-nbits = <64>; + vendor-id = <0x104c>; + device-id = <0xb010>; + msi-map = <0x0 &gic_its 0x0 0x10000>; + ranges = <0x01000000 0x00 0x68001000 0x00 0x68001000 0x00 0x0010000>, + <0x02000000 0x00 0x68011000 0x00 0x68011000 0x00 0x7fef000>; + dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x00000010 0x0>; + }; + + pcie0_ep: pcie-ep@f102000 { + compatible = "ti,am64-pcie-ep", "ti,j721e-pcie-ep"; + reg = <0x00 0x0f102000 0x00 0x1000>, + <0x00 0x0f100000 0x00 0x400>, + <0x00 0x0d000000 0x00 0x00800000>, + <0x00 0x68000000 0x00 0x08000000>; + reg-names = "intd_cfg", "user_cfg", "reg", "mem"; + interrupt-names = "link_state"; + interrupts = <GIC_SPI 203 IRQ_TYPE_EDGE_RISING>; + ti,syscon-pcie-ctrl = <&main_conf 0x4070>; + max-link-speed = <2>; + num-lanes = <1>; + power-domains = <&k3_pds 114 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 114 0>; + clock-names = "fck"; + max-functions = /bits/ 8 <1>; + }; };
Signature · 1 line
2.17.1
PATCH v2 4/6 arm64: dts: ti: k3-am642-evm: Enable PCIe and SERDES
In reply to Kishon Vijay Abraham IAM642 EVM has a x4 lane PCIe connector. Enable PCIe in RC mode here.
--- arch/arm64/boot/dts/ti/k3-am642-evm.dts | 30 +++++++++++++++++++++++++ 1 file changed, 30 insertions(+)
arch/arm64/boot/dts/ti/k3-am642-evm.dts +30 -0
@@ -5,6 +5,8 @@ /dts-v1/; +#include <dt-bindings/phy/phy.h> +#include <dt-bindings/mux/ti-serdes.h> #include <dt-bindings/leds/common.h> #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/net/ti-dp83867.h>
@@ -466,3 +468,31 @@ &mailbox0_cluster7 { status = "disabled"; }; + +&serdes_ln_ctrl { + idle-states = <AM64_SERDES0_LANE0_PCIE0>; +}; + +&serdes0 { + serdes0_pcie_link: phy@0 { + reg = <0>; + cdns,num-lanes = <1>; + #phy-cells = <0>; + cdns,phy-type = <PHY_TYPE_PCIE>; + resets = <&serdes_wiz0 1>; + }; +}; + +&pcie0_rc { + reset-gpios = <&exp1 5 GPIO_ACTIVE_HIGH>; + phys = <&serdes0_pcie_link>; + phy-names = "pcie-phy"; + num-lanes = <1>; +}; + +&pcie0_ep { + phys = <&serdes0_pcie_link>; + phy-names = "pcie-phy"; + num-lanes = <1>; + status = "disabled"; +};
Signature · 1 line
2.17.1
PATCH v2 5/6 arm64: dts: ti: k3-am642-sk: Enable USB Super-Speed HOST port
In reply to Kishon Vijay Abraham IEnable USB Super-Speed HOST port.
--- arch/arm64/boot/dts/ti/k3-am642-sk.dts | 35 ++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)
arch/arm64/boot/dts/ti/k3-am642-sk.dts +35 -0
@@ -5,6 +5,8 @@ /dts-v1/; +#include <dt-bindings/mux/ti-serdes.h> +#include <dt-bindings/phy/phy.h> #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/net/ti-dp83867.h> #include "k3-am642.dtsi"
@@ -85,6 +87,12 @@ >; }; + main_usb0_pins_default: main-usb0-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */ + >; + }; + main_i2c1_pins_default: main-i2c1-pins-default { pinctrl-single,pins = < AM64X_IOPAD(0x0268, PIN_INPUT_PULLUP, 0) /* (C18) I2C1_SCL */
@@ -235,6 +243,33 @@ disable-wp; }; +&serdes_ln_ctrl { + idle-states = <AM64_SERDES0_LANE0_USB>; +}; + +&serdes0 { + serdes0_usb_link: phy@0 { + reg = <0>; + cdns,num-lanes = <1>; + #phy-cells = <0>; + cdns,phy-type = <PHY_TYPE_USB3>; + resets = <&serdes_wiz0 1>; + }; +}; + +&usbss0 { + ti,vbus-divider; +}; + +&usb0 { + dr_mode = "host"; + maximum-speed = "super-speed"; + pinctrl-names = "default"; + pinctrl-0 = <&main_usb0_pins_default>; + phys = <&serdes0_usb_link>; + phy-names = "cdns3,usb3-phy"; +}; + &cpsw3g { pinctrl-names = "default"; pinctrl-0 = <&mdio1_pins_default
Signature · 1 line
2.17.1
PATCH v2 6/6 arm64: dts: ti: k3-am642-sk: Disable PCIe
In reply to Kishon Vijay Abraham IAM642-SK has no PCIe slot. Disable it here.
--- arch/arm64/boot/dts/ti/k3-am642-sk.dts | 8 ++++++++ 1 file changed, 8 insertions(+)
arch/arm64/boot/dts/ti/k3-am642-sk.dts +8 -0
@@ -367,3 +367,11 @@ &mailbox0_cluster7 { status = "disabled"; }; + +&pcie0_rc { + status = "disabled"; +}; + +&pcie0_ep { + status = "disabled"; +};
Signature · 1 line
2.17.1