arm64: synquacer: Add SynQuacer/DeveloperBox support
Subsystems (8)
v5 cover arm64: synquacer: Add SynQuacer/DeveloperBox support
Hi,
Here is the 5th version of the series (including some fixes for build errors) to add SynQuacer/DeveloperBox 96board EE suport on U-Boot.
This series includes not only DeveloperBox support but also some fixes for the issues which I faced while porting U-Boot on the DeveloperBox. First 3 patches are fixes, next 1 patch is a code cleanup for generic gpio for arm. The next 7 patches adding DeveloperBox devices and board support. The last 2 patches are related to the UEFI capsule update.
Previous version is here:
https://lists.denx.de/pipermail/u-boot/2021-May/449305.html
Changes in v5
-------------
I dripped dfu_mtd bugfix patch (previous [12/14]) from this, because Sughosh already fixed it.
[11/13]:
- Remove log level from config.
DeveloperBox
============
DeveloperBox is a certified 96boards Enterprise Edition board. The board/SoC has: -
* Socionext SC2A11 24-cores ARM Cortex-A53 on tbe Mini-ATX form factor motherboard
* 4 DIMM slots (4GB DDR4-2400 UDIMM shipped by default)
* 1 4xPCIe Gen2 slot and 2 1xPCIe Gen2 slots
(1x slots are connected via PCIe bridge chip)
* 4 USB-3.0 ports
* 2 SATA ports
* 1 GbE network port
* 1 USB-UART serial port (micro USB)
* 64MB SPI NOR Flash
* 8GB eMMC Flash Storage
* 96boards LS connector
The DeveloperBox schematic can be found here: -
https://www.96boards.org/documentation/enterprise/developerbox/hardware-docs/mzsc2am_v03_20180115_a.pdf
And the other documents can be found here: -
https://www.96boards.org/documentation/enterprise/developerbox/
Currently, the U-Boot port supports: -
* USB
* eMMC
* SPI-NOR
* SATA
* GbE
The DeveloperBox boots the TF-A and EDK2 as a main bootloader by default. The DeveloperBox U-Boot port will replace the EDK2 and boot from TF-A as BL33, but no need to combine with it.
Thank you,
---
Jassi Brar (4):
mmc: synquacer: Add SynQuacer F_SDH30 SDHCI driver
spi: synquacer: Add HSSPI SPI controller driver for SynQuacer
net: synquacer: Add netsec driver
i2c: synquacer: SNI Synquacer I2C controller
Masami Hiramatsu (9):
ata: ahci-pci: Use scsi_ops to initialize ops
dm: pci: Skip setting VGA bridge bits if parent device is the host bus
efi: Fix to use null handle to create new handle for efi_fmp_raw
gpio: Introduce CONFIG_GPIO_EXTRA_HEADER to cleanup #ifdefs
pci: synquacer: Add SynQuacer ECAM based PCIe driver
ARM: dts: synquacer: Add device trees for DeveloperBox
board: synquacer: Add DeveloperBox 96boards EE support
doc: qemu: arm64: Fix the documentation of capsule update
configs: synquacer: Enable EFI capsule update support
arch/arm/Kconfig | 108 ++ arch/arm/dts/Makefile | 2 arch/arm/dts/synquacer-sc2a11-caches.dtsi | 73 + .../dts/synquacer-sc2a11-developerbox-u-boot.dtsi | 75 + arch/arm/dts/synquacer-sc2a11-developerbox.dts | 56 + arch/arm/dts/synquacer-sc2a11.dtsi | 595 ++++++++++ arch/arm/include/asm/gpio.h | 8 board/socionext/developerbox/Kconfig | 36 + board/socionext/developerbox/MAINTAINERS | 14 board/socionext/developerbox/Makefile | 9 board/socionext/developerbox/developerbox.c | 146 +++ configs/synquacer_developerbox_defconfig | 129 ++ doc/board/emulation/qemu_capsule_update.rst | 11 doc/board/index.rst | 1 doc/board/socionext/developerbox.rst | 87 ++ doc/board/socionext/index.rst | 9 drivers/ata/ahci-pci.c | 2 drivers/i2c/Kconfig | 7 drivers/i2c/Makefile | 1 drivers/i2c/synquacer_i2c.c | 338 ++++++ drivers/mmc/Kconfig | 10 drivers/mmc/Makefile | 1 drivers/mmc/f_sdh30.c | 81 + drivers/net/Kconfig | 8 drivers/net/Makefile | 1 drivers/net/sni_netsec.c | 1134 ++++++++++++++++++++ drivers/pci/Kconfig | 12 drivers/pci/Makefile | 1 drivers/pci/pci-uclass.c | 3 drivers/pci/pcie_ecam_synquacer.c | 600 +++++++++++ drivers/spi/Kconfig | 8 drivers/spi/Makefile | 1 drivers/spi/spi-synquacer.c | 491 +++++++++ include/configs/synquacer.h | 115 ++ lib/efi_loader/efi_capsule.c | 2 35 files changed, 4158 insertions(+), 17 deletions(-) create mode 100644 arch/arm/dts/synquacer-sc2a11-caches.dtsi create mode 100644 arch/arm/dts/synquacer-sc2a11-developerbox-u-boot.dtsi create mode 100644 arch/arm/dts/synquacer-sc2a11-developerbox.dts create mode 100644 arch/arm/dts/synquacer-sc2a11.dtsi create mode 100644 board/socionext/developerbox/Kconfig create mode 100644 board/socionext/developerbox/MAINTAINERS create mode 100644 board/socionext/developerbox/Makefile create mode 100644 board/socionext/developerbox/developerbox.c create mode 100644 configs/synquacer_developerbox_defconfig create mode 100644 doc/board/socionext/developerbox.rst create mode 100644 doc/board/socionext/index.rst create mode 100644 drivers/i2c/synquacer_i2c.c create mode 100644 drivers/mmc/f_sdh30.c create mode 100644 drivers/net/sni_netsec.c create mode 100644 drivers/pci/pcie_ecam_synquacer.c create mode 100644 drivers/spi/spi-synquacer.c create mode 100644 include/configs/synquacer.h
--
Masami Hiramatsu <[email protected]>
PATCH v5 1/13 ata: ahci-pci: Use scsi_ops to initialize ops
Without this fix, scsi-scan will cause a synchronous abort when accessing ops->scan.
--- drivers/ata/ahci-pci.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/ata/ahci-pci.c +2 -0
@@ -5,6 +5,7 @@#include <common.h> #include <ahci.h> +#include <scsi.h> #include <dm.h> #include <pci.h>
@@ -28,6 +29,7 @@ static const struct udevice_id ahci_pci_ids[] = {U_BOOT_DRIVER (ahci_pci) = { .name ="ahci_pci" , .id =UCLASS_AHCI , + .ops = &scsi_ops, .of_match = ahci_pci_ids, .bind = ahci_pci_bind, .probe = ahci_pci_probe,
Re: [PATCH v5 01/13] ata: ahci-pci: Use scsi_ops to initialize ops
Quoted 5 lines · Masami Hiramatsu
Without this fix, scsi-scan will cause a synchronous abort when accessing
ops->scan.Signed-off-by Masami Hiramatsu <[email protected]>Reviewed-by Simon Glass <[email protected]>
For the entire series, applied to u-boot/master, thanks!
Signature · 1 line
Tom
Re: [PATCH v5 01/13] ata: ahci-pci: Use scsi_ops to initialize ops
Hi Tom,
2021年7月7日(水) 7:50 Tom Rini <[email protected]>:
Quoted 10 lines · Masami Hiramatsu
Quoted 6 lines
Without this fix, scsi-scan will cause a synchronous abort when accessing
ops->scan.Signed-off-by Masami Hiramatsu <[email protected]>Reviewed-by Simon Glass <[email protected]>For the entire series, applied to u-boot/master, thanks!
Thank you so much!
I have some updates, so I'll send it.
Regards,
Signature · 1 line
Masami Hiramatsu
PATCH v5 2/13 dm: pci: Skip setting VGA bridge bits if parent device is the host bus
In reply to Masami HiramatsuCommit bbbcb5262839 ("dm: pci: Enable VGA address forwarding on bridges") sets the VGA bridge bits by checking pplat->class, but if the parent device is the pci host bus device, it can be skipped. Moreover, it shouldn't access the pplat because the parent has different plat data.
Without this fix, "pci enum" command cause a synchronous abort.
pci_auto_config_devices: start
PCI Autoconfig: Bus Memory region: [78000000-7fffffff],
Physical Memory [78000000-7fffffffx] PCI Autoconfig: Bus I/O region: [0-ffff], Physical Memory [77f00000-77f0ffffx]
pci_auto_config_devices: device pci_6:0.0
PCI Autoconfig: BAR 0, Mem, size=0x1000000, address=0x78000000 bus_lower=0x79000000
PCI Autoconfig: BAR 1, Mem, size=0x8000000, No room in resource, avail start=79000000 / size=8000000, need=8000000
PCI: Failed autoconfig bar 14
PCI Autoconfig: BAR 2, I/O, size=0x4, address=0x1000 bus_lower=0x1004
PCI Autoconfig: BAR 3, Mem, size=0x2000000, address=0x7a000000 bus_lower=0x7c000000
PCI Autoconfig: BAR 4, I/O, size=0x80, address=0x1080 bus_lower=0x1100
PCI Autoconfig: ROM, size=0x80000, address=0x7c000000 bus_lower=0x7c080000
"Synchronous Abort" handler, esr 0x96000006
elr: 00000000e002bd28 lr : 00000000e002bce8 (reloc)
elr: 00000000fff6fd28 lr : 00000000fff6fce8 x0 : 0000000000001041 x1 : 000000000000003e x2 : 00000000ffb0f8c8 x3 : 0000000000000001 x4 : 0000000000000080 x5 : 0000000000000000 x6 : 00000000fff718fc x7 : 000000000000000f x8 : 00000000ffb0f238 x9 : 0000000000000008
x10: 0000000000000000 x11: 0000000000000010
x12: 0000000000000006 x13: 000000000001869f
x14: 00000000ffb0fcd0 x15: 0000000000000020
x16: 00000000fff71cc4 x17: 0000000000000000
x18: 00000000ffb13d90 x19: 00000000ffb14320
x20: 0000000000000000 x21: 00000000ffb14090
x22: 00000000ffb0f8c8 x23: 0000000000000001
x24: 00000000ffb14c10 x25: 0000000000000000
x26: 0000000000000000 x27: 0000000000000000
x28: 00000000ffb14c70 x29: 00000000ffb0f830
Code: 52800843 52800061 52800e00 97ffcf65 (b9400280)
Resetting CPU ...
--- drivers/pci/pci-uclass.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/pci/pci-uclass.c +3 -0
@@ -550,6 +550,9 @@ int pci_auto_config_devices(struct udevice *bus) max_bus = ret; sub_bus =max (sub_bus, max_bus); +if (dev_get_parent (dev) == bus) +continue ; + pplat =dev_get_parent_plat (dev);if (pplat->class == (PCI_CLASS_DISPLAY_VGA <<8 ))set_vga_bridge_bits (dev);
PATCH v5 3/13 efi: Fix to use null handle to create new handle for efi_fmp_raw
In reply to Masami HiramatsuWhen running the efidebug capsule disk-update command, the efi_fmp_raw protocol installation is failed with 2 (EFI_INVALID_PARAMETER) as below. This is because the code passes efi_root instaed of handle.
=> efidebug capsule disk-update
EFI: Call: efi_install_multiple_protocol_interfaces( &handle, &efi_guid_firmware_management_protocol, &efi_fmp_fit, NULL)
EFI: Entry efi_install_multiple_protocol_interfaces(00000000fbaf5988)
EFI: Call: efi_install_protocol_interface( handle, protocol, EFI_NATIVE_INTERFACE, protocol_interface)
EFI: Entry efi_install_protocol_interface(00000000fbaf5988, 86c77a67-0b97-4633-a187-49104d0685c7, 0, 00000000fbfa6ee8)
EFI: new handle 00000000fbb37520
EFI: Exit: efi_install_protocol_interface: 0
EFI: 0 returned by efi_install_protocol_interface( handle, protocol, EFI_NATIVE_INTERFACE, protocol_interface)
EFI: Exit: efi_install_multiple_protocol_interfaces: 0
EFI: 0 returned by efi_install_multiple_protocol_interfaces( &handle, &efi_guid_firmware_management_protocol, &efi_fmp_fit, NULL)
EFI: Call: efi_install_multiple_protocol_interfaces( &efi_root, &efi_guid_firmware_management_protocol, &efi_fmp_raw, NULL)
EFI: Entry efi_install_multiple_protocol_interfaces(00000000fbfec648)
EFI: Call: efi_install_protocol_interface( handle, protocol, EFI_NATIVE_INTERFACE, protocol_interface)
EFI: Entry efi_install_protocol_interface(00000000fbfec648, 86c77a67-0b97-4633-a187-49104d0685c7, 0, 00000000fbfa6f18)
EFI: handle 00000000fbaf8520
EFI: Exit: efi_install_protocol_interface: 2
EFI: 2 returned by efi_install_protocol_interface( handle, protocol, EFI_NATIVE_INTERFACE, protocol_interface)
EFI: Exit: efi_install_multiple_protocol_interfaces: 2
EFI: 2 returned by efi_install_multiple_protocol_interfaces( &efi_root, &efi_guid_firmware_management_protocol, &efi_fmp_raw, NULL) Command failed, result=1
To fix this issue, pass the handle variable as same as the efi_fmp_fit installation.
--- lib/efi_loader/efi_capsule.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
lib/efi_loader/efi_capsule.c +1 -1
@@ -939,7 +939,7 @@ efi_status_t __weak arch_efi_load_capsule_drivers(void)if (IS_ENABLED (CONFIG_EFI_CAPSULE_FIRMWARE_RAW )) { handle =NULL ; ret =EFI_CALL (efi_install_multiple_protocol_interfaces ( - &efi_root, + &handle, &efi_guid_firmware_management_protocol, &efi_fmp_raw,NULL )); }
PATCH v5 4/13 gpio: Introduce CONFIG_GPIO_EXTRA_HEADER to cleanup #ifdefs
In reply to Masami HiramatsuSince some SoCs and boards do not hae extra asm/arch/gpio.h, introduce CONFIG_GPIO_EXTRA_HEADER instead of adding !define(CONFIG_ARCH_XXXX) in asm/gpio.h.
---
Changes in v3:
- Change the config name to positive and selected by the opposite CONFIG_ARCH_*. (Build checked by Github CI)
--- arch/arm/Kconfig | 94 +++++++++++++++++++++++++++++++++++++++++++ arch/arm/include/asm/gpio.h | 8 ---- 2 files changed, 95 insertions(+), 7 deletions(-)
arch/arm/Kconfig +94 -0
@@ -90,6 +90,9 @@ config HAS_VBAR config HAS_THUMB2 bool +config GPIO_EXTRA_HEADER + bool + # Used for compatibility with asm files copied from the kernel config ARM_ASM_UNIFIED bool
@@ -518,25 +521,30 @@ choice config ARCH_AT91 bool "Atmel AT91" + select GPIO_EXTRA_HEADER select SPL_BOARD_INIT if SPL && !TARGET_SMARTWEB select SPL_SEPARATE_BSS if SPL config TARGET_EDB93XX bool "Support edb93xx" select CPU_ARM920T + select GPIO_EXTRA_HEADER select PL010_SERIAL config TARGET_ASPENITE bool "Support aspenite" select CPU_ARM926EJS + select GPIO_EXTRA_HEADER config TARGET_GPLUGD bool "Support gplugd" select CPU_ARM926EJS + select GPIO_EXTRA_HEADER config ARCH_DAVINCI bool "TI DaVinci" select CPU_ARM926EJS + select GPIO_EXTRA_HEADER select SPL_DM_SPI if SPL imply CMD_SAVES help
@@ -547,6 +555,7 @@ config ARCH_KIRKWOOD select ARCH_MISC_INIT select BOARD_EARLY_INIT_F select CPU_ARM926EJS + select GPIO_EXTRA_HEADER config ARCH_MVEBU bool "Marvell MVEBU family (Armada XP/375/38x/3700/7K/8K)"
@@ -555,6 +564,7 @@ config ARCH_MVEBU select DM_SERIAL select DM_SPI select DM_SPI_FLASH + select GPIO_EXTRA_HEADER select SPL_DM_SPI if SPL select SPL_DM_SPI_FLASH if SPL select OF_CONTROL
@@ -565,11 +575,13 @@ config ARCH_MVEBU config ARCH_ORION5X bool "Marvell Orion" select CPU_ARM926EJS + select GPIO_EXTRA_HEADER config TARGET_SPEAR300 bool "Support spear300" select BOARD_EARLY_INIT_F select CPU_ARM926EJS + select GPIO_EXTRA_HEADER select PL011_SERIAL imply CMD_SAVES
@@ -577,6 +589,7 @@ config TARGET_SPEAR310 bool "Support spear310" select BOARD_EARLY_INIT_F select CPU_ARM926EJS + select GPIO_EXTRA_HEADER select PL011_SERIAL imply CMD_SAVES
@@ -584,6 +597,7 @@ config TARGET_SPEAR320 bool "Support spear320" select BOARD_EARLY_INIT_F select CPU_ARM926EJS + select GPIO_EXTRA_HEADER select PL011_SERIAL imply CMD_SAVES
@@ -591,6 +605,7 @@ config TARGET_SPEAR600 bool "Support spear600" select BOARD_EARLY_INIT_F select CPU_ARM926EJS + select GPIO_EXTRA_HEADER select PL011_SERIAL imply CMD_SAVES
@@ -601,6 +616,7 @@ config TARGET_STV0991 select DM_SERIAL select DM_SPI select DM_SPI_FLASH + select GPIO_EXTRA_HEADER select PL01X_SERIAL select SPI select SPI_FLASH
@@ -610,18 +626,21 @@ config TARGET_X600 bool "Support x600" select BOARD_LATE_INIT select CPU_ARM926EJS + select GPIO_EXTRA_HEADER select PL011_SERIAL select SUPPORT_SPL config TARGET_FLEA3 bool "Support flea3" select CPU_ARM1136 + select GPIO_EXTRA_HEADER config ARCH_BCM283X bool "Broadcom BCM283X family" select DM select DM_GPIO select DM_SERIAL + select GPIO_EXTRA_HEADER select OF_CONTROL select PL01X_SERIAL select SERIAL_SEARCH_ALL
@@ -650,6 +669,7 @@ config ARCH_BCMSTB bool "Broadcom BCM7XXX family" select CPU_V7A select DM + select GPIO_EXTRA_HEADER select OF_CONTROL select OF_PRIOR_STAGE imply CMD_DM
@@ -660,6 +680,7 @@ config ARCH_BCMSTB config TARGET_BCMCYGNUS bool "Support bcmcygnus" select CPU_V7A + select GPIO_EXTRA_HEADER imply BCM_SF2_ETH imply BCM_SF2_ETH_GMAC imply CMD_HASH
@@ -671,6 +692,7 @@ config TARGET_BCMCYGNUS config TARGET_BCMNS2 bool "Support Broadcom Northstar2" select ARM64 + select GPIO_EXTRA_HEADER help Support for Broadcom Northstar 2 SoCs. NS2 is a quad-core 64-bit ARMv8 Cortex-A57 processors targeting a broad range of networking
@@ -695,6 +717,7 @@ config ARCH_EXYNOS select DM_SPI select DM_SPI_FLASH select SPI + select GPIO_EXTRA_HEADER imply SYS_THUMB_BUILD imply CMD_DM imply FAT_WRITE
@@ -706,6 +729,7 @@ config ARCH_S5PC1XX select DM_GPIO select DM_I2C select DM_SERIAL + select GPIO_EXTRA_HEADER imply CMD_DM config ARCH_HIGHBANK
@@ -726,6 +750,7 @@ config ARCH_INTEGRATOR bool "ARM Ltd. Integrator family" select DM select DM_SERIAL + select GPIO_EXTRA_HEADER select PL01X_SERIAL imply CMD_DM
@@ -736,6 +761,7 @@ config ARCH_IPQ40XX select DM_GPIO select DM_SERIAL select DM_RESET + select GPIO_EXTRA_HEADER select MSM_SMEM select PINCTRL select CLK
@@ -747,6 +773,7 @@ config ARCH_KEYSTONE bool "TI Keystone" select CMD_POWEROFF select CPU_V7A + select GPIO_EXTRA_HEADER select SUPPORT_SPL select SYS_ARCH_TIMER select SYS_THUMB_BUILD
@@ -763,6 +790,7 @@ config ARCH_K3 config ARCH_OMAP2PLUS bool "TI OMAP2+" select CPU_V7A + select GPIO_EXTRA_HEADER select SPL_BOARD_INIT if SPL select SPL_STACK_R if SPL select SUPPORT_SPL
@@ -771,6 +799,7 @@ config ARCH_OMAP2PLUS config ARCH_MESON bool "Amlogic Meson" + select GPIO_EXTRA_HEADER imply DISTRO_DEFAULTS imply DM_RNG help
@@ -781,6 +810,7 @@ config ARCH_MESON config ARCH_MEDIATEK bool "MediaTek SoCs" select DM + select GPIO_EXTRA_HEADER select OF_CONTROL select SPL_DM if SPL select SPL_LIBCOMMON_SUPPORT if SPL
@@ -797,6 +827,7 @@ config ARCH_LPC32XX select DM select DM_GPIO select DM_SERIAL + select GPIO_EXTRA_HEADER select SPL_DM if SPL select SUPPORT_SPL imply CMD_DM
@@ -805,12 +836,14 @@ config ARCH_IMX8 bool "NXP i.MX8 platform" select ARM64 select DM + select GPIO_EXTRA_HEADER select OF_CONTROL select ENABLE_ARM_SOC_BOOT0_HOOK config ARCH_IMX8M bool "NXP i.MX8M platform" select ARM64 + select GPIO_EXTRA_HEADER select SYS_FSL_HAS_SEC if IMX_HAB select SYS_FSL_SEC_COMPAT_4 select SYS_FSL_SEC_LE
@@ -823,33 +856,39 @@ config ARCH_IMXRT select CPU_V7M select DM select DM_SERIAL + select GPIO_EXTRA_HEADER select SUPPORT_SPL imply CMD_DM config ARCH_MX23 bool "NXP i.MX23 family" select CPU_ARM926EJS + select GPIO_EXTRA_HEADER select PL011_SERIAL select SUPPORT_SPL config ARCH_MX25 bool "NXP MX25" select CPU_ARM926EJS + select GPIO_EXTRA_HEADER imply MXC_GPIO config ARCH_MX28 bool "NXP i.MX28 family" select CPU_ARM926EJS + select GPIO_EXTRA_HEADER select PL011_SERIAL select SUPPORT_SPL config ARCH_MX31 bool "NXP i.MX31 family" select CPU_ARM1136 + select GPIO_EXTRA_HEADER config ARCH_MX7ULP bool "NXP MX7ULP" select CPU_V7A + select GPIO_EXTRA_HEADER select SYS_FSL_HAS_SEC if IMX_HAB select SYS_FSL_SEC_COMPAT_4 select SYS_FSL_SEC_LE
@@ -861,6 +900,7 @@ config ARCH_MX7 bool "Freescale MX7" select ARCH_MISC_INIT select CPU_V7A + select GPIO_EXTRA_HEADER select SYS_FSL_HAS_SEC if IMX_HAB select SYS_FSL_SEC_COMPAT_4 select SYS_FSL_SEC_LE
@@ -871,6 +911,7 @@ config ARCH_MX7 config ARCH_MX6 bool "Freescale MX6" select CPU_V7A + select GPIO_EXTRA_HEADER select SYS_FSL_HAS_SEC select SYS_FSL_SEC_COMPAT_4 select SYS_FSL_SEC_LE
@@ -886,18 +927,21 @@ config ARCH_MX5 bool "Freescale MX5" select BOARD_EARLY_INIT_F select CPU_V7A + select GPIO_EXTRA_HEADER imply MXC_GPIO config ARCH_NEXELL bool "Nexell S5P4418/S5P6818 SoC" select ENABLE_ARM_SOC_BOOT0_HOOK select DM + select GPIO_EXTRA_HEADER config ARCH_OWL bool "Actions Semi OWL SoCs" select DM select DM_ETH select DM_SERIAL + select GPIO_EXTRA_HEADER select OWL_SERIAL select CLK select CLK_OWL
@@ -920,6 +964,7 @@ config ARCH_RMOBILE bool "Renesas ARM SoCs" select DM select DM_SERIAL + select GPIO_EXTRA_HEADER imply BOARD_EARLY_INIT_F imply CMD_DM imply FAT_WRITE
@@ -932,6 +977,7 @@ config ARCH_SNAPDRAGON select DM select DM_GPIO select DM_SERIAL + select GPIO_EXTRA_HEADER select MSM_SMEM select OF_CONTROL select OF_SEPARATE
@@ -947,6 +993,7 @@ config ARCH_SOCFPGA select CPU_V7A if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10 select DM select DM_SERIAL + select GPIO_EXTRA_HEADER select ENABLE_ARM_SOC_BOOT0_HOOK if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10 select OF_CONTROL select SPL_DM_RESET if DM_RESET
@@ -998,6 +1045,7 @@ config ARCH_SUNXI select DM_SCSI if SCSI select DM_SERIAL select DM_USB if DISTRO_DEFAULTS + select GPIO_EXTRA_HEADER select OF_BOARD_SETUP select OF_CONTROL select OF_SEPARATE
@@ -1057,6 +1105,7 @@ config ARCH_VERSAL select DM_ETH if NET select DM_MMC if MMC select DM_SERIAL + select GPIO_EXTRA_HEADER select OF_CONTROL imply BOARD_LATE_INIT imply ENV_VARS_UBOOT_RUNTIME_CONFIG
@@ -1064,6 +1113,7 @@ config ARCH_VERSAL config ARCH_VF610 bool "Freescale Vybrid" select CPU_V7A + select GPIO_EXTRA_HEADER select SYS_FSL_ERRATUM_ESDHC111 imply CMD_MTDPARTS imply MTD_RAW_NAND
@@ -1080,6 +1130,7 @@ config ARCH_ZYNQ select DM_SPI select DM_SPI_FLASH select DM_USB if USB + select GPIO_EXTRA_HEADER select OF_CONTROL select SPI select SPL_BOARD_INIT if SPL
@@ -1106,6 +1157,7 @@ config ARCH_ZYNQMP_R5 select DM_ETH if NET select DM_MMC if MMC select DM_SERIAL + select GPIO_EXTRA_HEADER select OF_CONTROL imply CMD_DM imply DM_USB_GADGET
@@ -1123,6 +1175,7 @@ config ARCH_ZYNQMP select DM_SPI_FLASH if DM_SPI select DM_USB if USB select FIRMWARE + select GPIO_EXTRA_HEADER select OF_CONTROL select SPL_BOARD_INIT if SPL select SPL_CLK if SPL
@@ -1143,23 +1196,27 @@ config ARCH_ZYNQMP config ARCH_TEGRA bool "NVIDIA Tegra" + select GPIO_EXTRA_HEADER imply DISTRO_DEFAULTS imply FAT_WRITE config TARGET_VEXPRESS64_AEMV8A bool "Support vexpress_aemv8a" select ARM64 + select GPIO_EXTRA_HEADER select PL01X_SERIAL config TARGET_VEXPRESS64_BASE_FVP bool "Support Versatile Express ARMv8a FVP BASE model" select ARM64 + select GPIO_EXTRA_HEADER select PL01X_SERIAL select SEMIHOSTING config TARGET_VEXPRESS64_JUNO bool "Support Versatile Express Juno Development Platform" select ARM64 + select GPIO_EXTRA_HEADER select PL01X_SERIAL select DM select OF_CONTROL
@@ -1188,6 +1245,7 @@ config TARGET_LS2080A_EMU select ARM64 select ARMV8_MULTIENTRY select FSL_DDR_SYNC_REFRESH + select GPIO_EXTRA_HEADER help Support for Freescale LS2080A_EMU platform. The LS2080A Development System (EMULATOR) is a pre-silicon
@@ -1201,6 +1259,7 @@ config TARGET_LS1088AQDS select ARMV8_MULTIENTRY select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER select SUPPORT_SPL select FSL_DDR_INTERACTIVE if !SD_BOOT help
@@ -1216,6 +1275,7 @@ config TARGET_LS2080AQDS select ARMV8_MULTIENTRY select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER select SUPPORT_SPL imply SCSI imply SCSI_AHCI
@@ -1237,6 +1297,7 @@ config TARGET_LS2080ARDB select SUPPORT_SPL select FSL_DDR_BIST select FSL_DDR_INTERACTIVE if !SPL + select GPIO_EXTRA_HEADER imply SCSI imply SCSI_AHCI help
@@ -1251,6 +1312,7 @@ config TARGET_LS2081ARDB select ARM64 select ARMV8_MULTIENTRY select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER select SUPPORT_SPL help Support for Freescale LS2081ARDB platform.
@@ -1265,6 +1327,7 @@ config TARGET_LX2160ARDB select ARMV8_MULTIENTRY select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER help Support for NXP LX2160ARDB platform. The lx2160ardb (LX2160A Reference design board (RDB)
@@ -1278,6 +1341,7 @@ config TARGET_LX2160AQDS select ARMV8_MULTIENTRY select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER help Support for NXP LX2160AQDS platform. The lx2160aqds (LX2160A QorIQ Development System (QDS)
@@ -1292,6 +1356,7 @@ config TARGET_LX2162AQDS select ARMV8_MULTIENTRY select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER help Support for NXP LX2162AQDS platform. The lx2162aqds support is based on LX2160A Layerscape Architecture processor.
@@ -1302,6 +1367,7 @@ config TARGET_HIKEY select DM select DM_GPIO select DM_SERIAL + select GPIO_EXTRA_HEADER select OF_CONTROL select PL01X_SERIAL select SPECIFY_CONSOLE_INDEX
@@ -1315,6 +1381,7 @@ config TARGET_HIKEY960 select ARM64 select DM select DM_SERIAL + select GPIO_EXTRA_HEADER select OF_CONTROL select PL01X_SERIAL imply CMD_DM
@@ -1328,6 +1395,7 @@ config TARGET_POPLAR select DM select DM_SERIAL select DM_USB + select GPIO_EXTRA_HEADER select OF_CONTROL select PL01X_SERIAL imply CMD_DM
@@ -1343,6 +1411,7 @@ config TARGET_LS1012AQDS select ARM64 select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER help Support for Freescale LS1012AQDS platform. The LS1012A Development System (QDS) is a high-performance
@@ -1355,6 +1424,7 @@ config TARGET_LS1012ARDB select ARM64 select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER imply SCSI imply SCSI_AHCI help
@@ -1369,6 +1439,7 @@ config TARGET_LS1012A2G5RDB select ARM64 select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER imply SCSI help Support for Freescale LS1012A2G5RDB platform.
@@ -1382,6 +1453,7 @@ config TARGET_LS1012AFRWY select ARM64 select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER imply SCSI imply SCSI_AHCI help
@@ -1395,6 +1467,7 @@ config TARGET_LS1012AFRDM select ARCH_LS1012A select ARM64 select ARCH_SUPPORT_TFABOOT + select GPIO_EXTRA_HEADER help Support for Freescale LS1012AFRDM platform. The LS1012A Freedom board (FRDM) is a high-performance
@@ -1408,6 +1481,7 @@ config TARGET_LS1028AQDS select ARMV8_MULTIENTRY select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER help Support for Freescale LS1028AQDS platform The LS1028A Development System (QDS) is a high-performance
@@ -1421,6 +1495,7 @@ config TARGET_LS1028ARDB select ARMV8_MULTIENTRY select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER help Support for Freescale LS1028ARDB platform The LS1028A Development System (RDB) is a high-performance
@@ -1436,6 +1511,7 @@ config TARGET_LS1088ARDB select BOARD_LATE_INIT select SUPPORT_SPL select FSL_DDR_INTERACTIVE if !SD_BOOT + select GPIO_EXTRA_HEADER help Support for NXP LS1088ARDB platform. The LS1088A Reference design board (RDB) is a high-performance
@@ -1456,6 +1532,7 @@ config TARGET_LS1021AQDS select SYS_FSL_DDR select FSL_DDR_INTERACTIVE select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI + select GPIO_EXTRA_HEADER select SPI_FLASH_DATAFLASH if FSL_DSPI || FSL_QSPI imply SCSI
@@ -1471,6 +1548,7 @@ config TARGET_LS1021ATWR select LS1_DEEP_SLEEP select SUPPORT_SPL select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI + select GPIO_EXTRA_HEADER imply SCSI config TARGET_PG_WCOM_SELI8
@@ -1484,6 +1562,7 @@ config TARGET_PG_WCOM_SELI8 select CPU_V7_HAS_VIRT select SYS_FSL_DDR select FSL_DDR_INTERACTIVE + select GPIO_EXTRA_HEADER select VENDOR_KM imply SCSI help
@@ -1502,6 +1581,7 @@ config TARGET_LS1021ATSN select CPU_V7_HAS_VIRT select LS1_DEEP_SLEEP select SUPPORT_SPL + select GPIO_EXTRA_HEADER imply SCSI config TARGET_LS1021AIOT
@@ -1514,6 +1594,7 @@ config TARGET_LS1021AIOT select CPU_V7_HAS_VIRT select SUPPORT_SPL select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI + select GPIO_EXTRA_HEADER imply SCSI help Support for Freescale LS1021AIOT platform.
@@ -1533,6 +1614,7 @@ config TARGET_LS1043AQDS select FSL_DDR_INTERACTIVE if !SPL select FSL_DSPI if !SPL_NO_DSPI select DM_SPI_FLASH if FSL_DSPI + select GPIO_EXTRA_HEADER imply SCSI imply SCSI_AHCI help
@@ -1549,6 +1631,7 @@ config TARGET_LS1043ARDB select SUPPORT_SPL select FSL_DSPI if !SPL_NO_DSPI select DM_SPI_FLASH if FSL_DSPI + select GPIO_EXTRA_HEADER help Support for Freescale LS1043ARDB platform.
@@ -1565,6 +1648,7 @@ config TARGET_LS1046AQDS select FSL_DDR_BIST if !SPL select FSL_DDR_INTERACTIVE if !SPL select FSL_DDR_INTERACTIVE if !SPL + select GPIO_EXTRA_HEADER imply SCSI help Support for Freescale LS1046AQDS platform.
@@ -1585,6 +1669,7 @@ config TARGET_LS1046ARDB select SUPPORT_SPL select FSL_DDR_BIST select FSL_DDR_INTERACTIVE if !SPL + select GPIO_EXTRA_HEADER imply SCSI help Support for Freescale LS1046ARDB platform.
@@ -1601,6 +1686,7 @@ config TARGET_LS1046AFRWY select BOARD_EARLY_INIT_F select BOARD_LATE_INIT select DM_SPI_FLASH if DM_SPI + select GPIO_EXTRA_HEADER imply SCSI help Support for Freescale LS1046AFRWY platform.
@@ -1629,6 +1715,7 @@ config TARGET_SL28 select DM_SERIAL select DM_SPI select DM_USB + select GPIO_EXTRA_HEADER select SPL_DM if SPL select SPL_DM_SPI if SPL select SPL_DM_SPI_FLASH if SPL
@@ -1641,6 +1728,7 @@ config TARGET_SL28 config TARGET_COLIBRI_PXA270 bool "Support colibri_pxa270" select CPU_PXA + select GPIO_EXTRA_HEADER config ARCH_UNIPHIER bool "Socionext UniPhier SoCs"
@@ -1677,6 +1765,7 @@ config ARCH_STM32 select CPU_V7M select DM select DM_SERIAL + select GPIO_EXTRA_HEADER imply CMD_DM config ARCH_STI
@@ -1702,6 +1791,7 @@ config ARCH_STM32MP select DM_GPIO select DM_RESET select DM_SERIAL + select GPIO_EXTRA_HEADER select MISC select OF_CONTROL select OF_LIBFDT
@@ -1764,6 +1854,7 @@ config ARCH_OCTEONTX bool "Support OcteonTX SoCs" select CLK select DM + select GPIO_EXTRA_HEADER select ARM64 select OF_CONTROL select OF_LIVE
@@ -1774,6 +1865,7 @@ config ARCH_OCTEONTX2 bool "Support OcteonTX2 SoCs" select CLK select DM + select GPIO_EXTRA_HEADER select ARM64 select OF_CONTROL select OF_LIVE
@@ -1783,6 +1875,7 @@ config ARCH_OCTEONTX2 config TARGET_THUNDERX_88XX bool "Support ThunderX 88xx" select ARM64 + select GPIO_EXTRA_HEADER select OF_CONTROL select PL01X_SERIAL select SYS_CACHE_SHIFT_7
@@ -1796,6 +1889,7 @@ config ARCH_ASPEED config TARGET_DURIAN bool "Support Phytium Durian Platform" select ARM64 + select GPIO_EXTRA_HEADER help Support for durian platform. It has 2GB Sdram, uart and pcie.
arch/arm/include/asm/gpio.h +1 -7
@@ -1,10 +1,4 @@ -#if !defined(CONFIG_ARCH_UNIPHIER ) && !defined(CONFIG_ARCH_STI ) && \ - !defined(CONFIG_ARCH_K3 ) && !defined(CONFIG_ARCH_BCM68360 ) && \ - !defined(CONFIG_ARCH_BCM6858 ) && !defined(CONFIG_ARCH_BCM63158 ) && \ - !defined(CONFIG_ARCH_ROCKCHIP ) && !defined(CONFIG_ARCH_ASPEED ) && \ - !defined(CONFIG_ARCH_U8500 ) && !defined(CONFIG_CORTINA_PLATFORM ) && \ - !defined(CONFIG_TARGET_BCMNS3 ) && !defined(CONFIG_TARGET_TOTAL_COMPUTE ) && \ - !defined(CONFIG_ARCH_QEMU ) +#ifdef CONFIG_GPIO_EXTRA_HEADER #include <asm/arch/gpio.h> #endif #include <asm-generic/gpio.h>
PATCH v5 5/13 pci: synquacer: Add SynQuacer ECAM based PCIe driver
In reply to Masami HiramatsuAdd ECAM based SynQuacer PCIe RC driver. This driver configures the PCIe RC and filter out a ghost pcie config.
Since the Linux kernel expects "socionext,synquacer-pcie-ecam" device is configured by firmware (EDK2), it doesn't re-configure in the kernel. So as same as EDK2, U-Boot needs to configure it before boot the kernel.
--- drivers/pci/Kconfig | 12 + drivers/pci/Makefile | 1 drivers/pci/pcie_ecam_synquacer.c | 600 +++++++++++++++++++++++++++++++++++++ 3 files changed, 613 insertions(+) create mode 100644 drivers/pci/pcie_ecam_synquacer.c
drivers/pci/Kconfig +12 -0
@@ -81,6 +81,18 @@ config PCIE_ECAM_GENERIC Say Y here if you want to enable support for generic ECAM-based PCIe host controllers, such as the one emulated by QEMU. +config PCIE_ECAM_SYNQUACER + bool "SynQuacer ECAM-based PCI host controller support" + default n + depends on DM_PCI + select PCI_INIT_R + select PCI_REGION_MULTI_ENTRY + help + Say Y here if you want to enable support for Socionext + SynQuacer SoC's ECAM-based PCIe host controllers. + Note that this must be configured when boot because Linux driver + expects the PCIe RC has been configured in the bootloader. + config PCI_PHYTIUM bool "Phytium PCIe support" depends on DM_PCI
drivers/pci/Makefile +1 -0
@@ -16,6 +16,7 @@ endif obj-$(CONFIG_PCI) += pci_auto_common.o pci_common.o obj-$(CONFIG_PCIE_ECAM_GENERIC) += pcie_ecam_generic.o +obj-$(CONFIG_PCIE_ECAM_SYNQUACER) += pcie_ecam_synquacer.o obj-$(CONFIG_FSL_PCI_INIT) += fsl_pci_init.o obj-$(CONFIG_PCI_INDIRECT_BRIDGE) += pci_indirect.o obj-$(CONFIG_PCI_GT64120) += pci_gt64120.o
drivers/pci/pcie_ecam_synquacer.c new file +600 -0
600 lines not on this page · raw message
PATCH v5 6/13 mmc: synquacer: Add SynQuacer F_SDH30 SDHCI driver
In reply to Masami HiramatsuFrom: Jassi Brar <[email protected]>
---
Changes in v4:
- Add Jaehoon's reviewed-by.
Changes in v3:
- Rename config name to MMC_SDHCI_F_SDH30.
- Remove unneeded wait in drivers/mmc/sdhci.c.
- Rename probe function to f_sdh30_sdhci_probe.
--- drivers/mmc/Kconfig | 10 ++++++ drivers/mmc/Makefile | 1 + drivers/mmc/f_sdh30.c | 81 +++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 92 insertions(+) create mode 100644 drivers/mmc/f_sdh30.c
drivers/mmc/Kconfig +10 -0
@@ -561,6 +561,16 @@ config MMC_SDHCI_IPROC If unsure, say N. +config MMC_SDHCI_F_SDH30 + bool "SDHCI support for Fujitsu Semiconductor F_SDH30" + depends on BLK && DM_MMC + depends on MMC_SDHCI + help + This selects the Secure Digital Host Controller Interface (SDHCI) + Needed by some Fujitsu SoC for MMC / SD / SDIO support. + If you have a controller with this interface, say Y or M here. + If unsure, say N. + config MMC_SDHCI_KONA bool "SDHCI support on Broadcom KONA platform" depends on MMC_SDHCI
drivers/mmc/Makefile +1 -0
@@ -76,3 +76,4 @@ obj-$(CONFIG_MMC_UNIPHIER) += tmio-common.o uniphier-sd.o obj-$(CONFIG_RENESAS_SDHI) += tmio-common.o renesas-sdhi.o obj-$(CONFIG_MMC_BCM2835) += bcm2835_sdhost.o obj-$(CONFIG_MMC_MTK) += mtk-sd.o +obj-$(CONFIG_MMC_SDHCI_F_SDH30) += f_sdh30.o
drivers/mmc/f_sdh30.c new file +81 -0
81 lines not on this page · raw message
PATCH v5 7/13 spi: synquacer: Add HSSPI SPI controller driver for SynQuacer
In reply to Masami HiramatsuFrom: Jassi Brar <[email protected]>
This is a driver for the HSSPI SPI controller on SynQuacer SoC. The HSSPI has command sequence mode (memory mapped) and direct mode (FIFO access). The driver will operate it under the direct mode. And before booting OS, it switch back to the command sequence mode since that is compatible with default EDK2 behavior.
--- drivers/spi/Kconfig | 8 + drivers/spi/Makefile | 1 drivers/spi/spi-synquacer.c | 491 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 500 insertions(+) create mode 100644 drivers/spi/spi-synquacer.c
drivers/spi/Kconfig +8 -0
@@ -481,4 +481,12 @@ config MXC_SPI Enable the MXC SPI controller driver. This driver can be used on various i.MX SoCs such as i.MX31/35/51/6/7. +config SYNQUACER_SPI + bool "Socionext SynQuacer HS-SPI driver" + depends on ARCH_SYNQUACER + help + Enable the Socionext HS-SPI driver for SynQuacer. This driver can + be used to access the SPI interface and SPI NOR flash on platforms + embedding this HS-SPI IP core. + endif # menu "SPI Support"
drivers/spi/Makefile +1 -0
@@ -31,6 +31,7 @@ obj-$(CONFIG_EXYNOS_SPI) += exynos_spi.o obj-$(CONFIG_FSL_DSPI) += fsl_dspi.o obj-$(CONFIG_FSL_ESPI) += fsl_espi.o obj-$(CONFIG_FSL_QSPI) += fsl_qspi.o +obj-$(CONFIG_SYNQUACER_SPI) += spi-synquacer.o obj-$(CONFIG_ICH_SPI) += ich.o obj-$(CONFIG_KIRKWOOD_SPI) += kirkwood_spi.o obj-$(CONFIG_MESON_SPIFC) += meson_spifc.o
drivers/spi/spi-synquacer.c new file +491 -0
491 lines not on this page · raw message
PATCH v5 8/13 net: synquacer: Add netsec driver
In reply to Masami HiramatsuFrom: Jassi Brar <[email protected]>
Add SynQuacer's NETSEC GbE controller driver. Since this driver will load the firmware from SPI NOR flash, this depends on CONFIG_SYNQUACER_SPI=y.
--- drivers/net/Kconfig | 8 drivers/net/Makefile | 1 drivers/net/sni_netsec.c | 1134 ++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 1143 insertions(+) create mode 100644 drivers/net/sni_netsec.c
drivers/net/Kconfig +8 -0
@@ -673,6 +673,14 @@ config SNI_AVE This driver implements support for the Socionext AVE Ethernet controller, as found on the Socionext UniPhier family. +config SNI_NETSEC + bool "Socionext NETSEC Ethernet support" + depends on DM_ETH && SYNQUACER_SPI + select PHYLIB + help + This driver implements support for the Socionext SynQuacer NETSEC + ethernet controller, as found on the Socionext SynQuacer family. + source "drivers/net/mscc_eswitch/Kconfig" config ETHER_ON_FEC1
drivers/net/Makefile +1 -0
@@ -89,6 +89,7 @@ obj-$(CONFIG_DWC_ETH_QOS) += dwc_eth_qos.o obj-$(CONFIG_FSL_PFE) += pfe_eth/ obj-y += qe/ obj-$(CONFIG_SNI_AVE) += sni_ave.o +obj-$(CONFIG_SNI_NETSEC) += sni_netsec.o obj-y += ti/ obj-$(CONFIG_MEDIATEK_ETH) += mtk_eth.o obj-y += mscc_eswitch/
drivers/net/sni_netsec.c new file +1134 -0
1,134 lines not on this page · raw message
Re: [PATCH v5 08/13] net: synquacer: Add netsec driver
Quoted 1,177 lines · Masami Hiramatsu
From: Jassi Brar <[email protected]>
Add SynQuacer's NETSEC GbE controller driver. Since this driver will load the firmware from SPI NOR flash, this depends on
CONFIG_SYNQUACER_SPI=y.Signed-off-by Jassi Brar <[email protected]>--- drivers/net/Kconfig | 8 drivers/net/Makefile | 1 drivers/net/sni_netsec.c | 1134 ++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 1143 insertions(+) create mode 100644 drivers/net/sni_netsec.cdrivers/net/Kconfig +8
-0@@ -673,6 +673,14 @@ config SNI_AVE This driver implements support for the Socionext AVE Ethernet controller, as found on the Socionext UniPhier family. +config SNI_NETSEC + bool "Socionext NETSEC Ethernet support" + depends on DM_ETH && SYNQUACER_SPI + select PHYLIB + help + This driver implements support for the Socionext SynQuacer NETSEC + ethernet controller, as found on the Socionext SynQuacer family. + source "drivers/net/mscc_eswitch/Kconfig" config ETHER_ON_FEC1drivers/net/Makefile +1
-0@@ -89,6 +89,7 @@ obj-$(CONFIG_DWC_ETH_QOS) += dwc_eth_qos.o obj-$(CONFIG_FSL_PFE) += pfe_eth/ obj-y += qe/ obj-$(CONFIG_SNI_AVE) += sni_ave.o +obj-$(CONFIG_SNI_NETSEC) += sni_netsec.o obj-y += ti/ obj-$(CONFIG_MEDIATEK_ETH) += mtk_eth.o obj-y += mscc_eswitch/drivers/net/sni_netsec.c new file +1124
-0@@ -0,0 +1,1134 @@ +// SPDX-License-Identifier: GPL-2.0+ +/** +* netsec.c - Socionext Synquacer Netsec driver +* Copyright 2021 Linaro Ltd. +*/ + +#include <clk.h> +#include <cpu_func.h> +#include <dm.h> +#include <fdt_support.h> +#include <log.h> +#include <malloc.h> +#include <miiphy.h> +#include <net.h> +#include <regmap.h> +#include <reset.h> +#include <syscon.h> +#include <asm/cache.h> +#include <asm/global_data.h> +#include <dm/device_compat.h> +#include <linux/bitops.h> +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/iopoll.h> +#include <spi.h> +#include <spi_flash.h> + +#define NETSEC_REG_SOFT_RST 0x104 +#define NETSEC_REG_COM_INIT 0x120 + +#define NETSEC_REG_TOP_STATUS 0x200 +#define NETSEC_IRQ_RX BIT(1) +#define NETSEC_IRQ_TX BIT(0) + +#define NETSEC_REG_TOP_INTEN 0x204 +#define NETSEC_REG_INTEN_SET 0x234 +#define NETSEC_REG_INTEN_CLR 0x238 + +#define NETSEC_REG_NRM_TX_STATUS 0x400 +#define NETSEC_REG_NRM_TX_INTEN 0x404 +#define NETSEC_REG_NRM_TX_INTEN_SET 0x428 +#define NETSEC_REG_NRM_TX_INTEN_CLR 0x42c +#define NRM_TX_ST_NTOWNR BIT(17) +#define NRM_TX_ST_TR_ERR BIT(16) +#define NRM_TX_ST_TXDONE BIT(15) +#define NRM_TX_ST_TMREXP BIT(14) + +#define NETSEC_REG_NRM_RX_STATUS 0x440 +#define NETSEC_REG_NRM_RX_INTEN 0x444 +#define NETSEC_REG_NRM_RX_INTEN_SET 0x468 +#define NETSEC_REG_NRM_RX_INTEN_CLR 0x46c +#define NRM_RX_ST_RC_ERR BIT(16) +#define NRM_RX_ST_PKTCNT BIT(15) +#define NRM_RX_ST_TMREXP BIT(14) + +#define NETSEC_REG_PKT_CMD_BUF 0xd0 + +#define NETSEC_REG_CLK_EN 0x100 + +#define NETSEC_REG_PKT_CTRL 0x140 + +#define NETSEC_REG_DMA_TMR_CTRL 0x20c +#define NETSEC_REG_F_TAIKI_MC_VER 0x22c +#define NETSEC_REG_F_TAIKI_VER 0x230 +#define NETSEC_REG_DMA_HM_CTRL 0x214 +#define NETSEC_REG_DMA_MH_CTRL 0x220 +#define NETSEC_REG_ADDR_DIS_CORE 0x218 +#define NETSEC_REG_DMAC_HM_CMD_BUF 0x210 +#define NETSEC_REG_DMAC_MH_CMD_BUF 0x21c + +#define NETSEC_REG_NRM_TX_PKTCNT 0x410 + +#define NETSEC_REG_NRM_TX_DONE_PKTCNT 0x414 +#define NETSEC_REG_NRM_TX_DONE_TXINT_PKTCNT 0x418 + +#define NETSEC_REG_NRM_TX_TMR 0x41c + +#define NETSEC_REG_NRM_RX_PKTCNT 0x454 +#define NETSEC_REG_NRM_RX_RXINT_PKTCNT 0x458 +#define NETSEC_REG_NRM_TX_TXINT_TMR 0x420 +#define NETSEC_REG_NRM_RX_RXINT_TMR 0x460 + +#define NETSEC_REG_NRM_RX_TMR 0x45c + +#define NETSEC_REG_NRM_TX_DESC_START_UP 0x434 +#define NETSEC_REG_NRM_TX_DESC_START_LW 0x408 +#define NETSEC_REG_NRM_RX_DESC_START_UP 0x474 +#define NETSEC_REG_NRM_RX_DESC_START_LW 0x448 + +#define NETSEC_REG_NRM_TX_CONFIG 0x430 +#define NETSEC_REG_NRM_RX_CONFIG 0x470 + +#define MAC_REG_STATUS 0x1024 +#define MAC_REG_DATA 0x11c0 +#define MAC_REG_CMD 0x11c4 +#define MAC_REG_FLOW_TH 0x11cc +#define MAC_REG_INTF_SEL 0x11d4 +#define MAC_REG_DESC_INIT 0x11fc +#define MAC_REG_DESC_SOFT_RST 0x1204 +#define NETSEC_REG_MODE_TRANS_COMP_STATUS 0x500 + +#define GMAC_REG_MCR 0x0000 +#define GMAC_REG_MFFR 0x0004 +#define GMAC_REG_GAR 0x0010 +#define GMAC_REG_GDR 0x0014 +#define GMAC_REG_FCR 0x0018 +#define GMAC_REG_BMR 0x1000 +#define GMAC_REG_RDLAR 0x100c +#define GMAC_REG_TDLAR 0x1010 +#define GMAC_REG_OMR 0x1018 + +#define MHZ (n) ((n) * 1000 * 1000) + +#define NETSEC_TX_SHIFT_OWN_FIELD 31 +#define NETSEC_TX_SHIFT_LD_FIELD 30 +#define NETSEC_TX_SHIFT_DRID_FIELD 24 +#define NETSEC_TX_SHIFT_PT_FIELD 21 +#define NETSEC_TX_SHIFT_TDRID_FIELD 16 +#define NETSEC_TX_SHIFT_CC_FIELD 15 +#define NETSEC_TX_SHIFT_FS_FIELD 9 +#define NETSEC_TX_LAST 8 +#define NETSEC_TX_SHIFT_CO 7 +#define NETSEC_TX_SHIFT_SO 6 +#define NETSEC_TX_SHIFT_TRS_FIELD 4 + +#define NETSEC_RX_PKT_OWN_FIELD 31 +#define NETSEC_RX_PKT_LD_FIELD 30 +#define NETSEC_RX_PKT_SDRID_FIELD 24 +#define NETSEC_RX_PKT_FR_FIELD 23 +#define NETSEC_RX_PKT_ER_FIELD 21 +#define NETSEC_RX_PKT_ERR_FIELD 16 +#define NETSEC_RX_PKT_TDRID_FIELD 12 +#define NETSEC_RX_PKT_FS_FIELD 9 +#define NETSEC_RX_PKT_LS_FIELD 8 +#define NETSEC_RX_PKT_CO_FIELD 6 + +#define NETSEC_RX_PKT_ERR_MASK 3 + +#define NETSEC_MAX_TX_PKT_LEN 1518 +#define NETSEC_MAX_TX_JUMBO_PKT_LEN 9018 + +#define NETSEC_RING_GMAC 15 +#define NETSEC_RING_MAX 2 + +#define NETSEC_TCP_SEG_LEN_MAX 1460 +#define NETSEC_TCP_JUMBO_SEG_LEN_MAX 8960 + +#define NETSEC_RX_CKSUM_NOTAVAIL 0 +#define NETSEC_RX_CKSUM_OK 1 +#define NETSEC_RX_CKSUM_NG 2 + +#define NETSEC_TOP_IRQ_REG_ME_START BIT(20) +#define NETSEC_IRQ_TRANSITION_COMPLETE BIT(4) + +#define NETSEC_MODE_TRANS_COMP_IRQ_N2T BIT(20) +#define NETSEC_MODE_TRANS_COMP_IRQ_T2N BIT(19) + +#define NETSEC_INT_PKTCNT_MAX 2047 + +#define NETSEC_FLOW_START_TH_MAX 95 +#define NETSEC_FLOW_STOP_TH_MAX 95 +#define NETSEC_FLOW_PAUSE_TIME_MIN 5 + +#define NETSEC_CLK_EN_REG_DOM_ALL 0x3f + +#define NETSEC_PKT_CTRL_REG_MODE_NRM BIT(28) +#define NETSEC_PKT_CTRL_REG_EN_JUMBO BIT(27) +#define NETSEC_PKT_CTRL_REG_LOG_CHKSUM_ER BIT(3) +#define NETSEC_PKT_CTRL_REG_LOG_HD_INCOMPLETE BIT(2) +#define NETSEC_PKT_CTRL_REG_LOG_HD_ER BIT(1) +#define NETSEC_PKT_CTRL_REG_DRP_NO_MATCH BIT(0) + +#define NETSEC_CLK_EN_REG_DOM_G BIT(5) +#define NETSEC_CLK_EN_REG_DOM_C BIT(1) +#define NETSEC_CLK_EN_REG_DOM_D BIT(0) + +#define NETSEC_COM_INIT_REG_DB BIT(2) +#define NETSEC_COM_INIT_REG_CLS BIT(1) +#define NETSEC_COM_INIT_REG_ALL (NETSEC_COM_INIT_REG_CLS | \ + NETSEC_COM_INIT_REG_DB) + +#define NETSEC_SOFT_RST_REG_RESET 0 +#define NETSEC_SOFT_RST_REG_RUN BIT(31) + +#define NETSEC_DMA_CTRL_REG_STOP 1 +#define MH_CTRL__MODE_TRANS BIT(20) + +#define NETSEC_GMAC_CMD_ST_READ 0 +#define NETSEC_GMAC_CMD_ST_WRITE BIT(28) +#define NETSEC_GMAC_CMD_ST_BUSY BIT(31) + +#define NETSEC_GMAC_BMR_REG_COMMON 0x00412080 +#define NETSEC_GMAC_BMR_REG_RESET 0x00020181 +#define NETSEC_GMAC_BMR_REG_SWR 0x00000001 + +#define NETSEC_GMAC_OMR_REG_ST BIT(13) +#define NETSEC_GMAC_OMR_REG_SR BIT(1) + +#define NETSEC_GMAC_MCR_REG_IBN BIT(30) +#define NETSEC_GMAC_MCR_REG_CST BIT(25) +#define NETSEC_GMAC_MCR_REG_JE BIT(20) +#define NETSEC_MCR_PS BIT(15) +#define NETSEC_GMAC_MCR_REG_FES BIT(14) +#define NETSEC_GMAC_MCR_REG_FULL_DUPLEX_COMMON 0x0000280c +#define NETSEC_GMAC_MCR_REG_HALF_DUPLEX_COMMON 0x0001a00c + +#define NETSEC_FCR_RFE BIT(2) +#define NETSEC_FCR_TFE BIT(1) + +#define NETSEC_GMAC_GAR_REG_GW BIT(1) +#define NETSEC_GMAC_GAR_REG_GB BIT(0) + +#define NETSEC_GMAC_GAR_REG_SHIFT_PA 11 +#define NETSEC_GMAC_GAR_REG_SHIFT_GR 6 +#define GMAC_REG_SHIFT_CR_GAR 2 + +#define NETSEC_GMAC_GAR_REG_CR_25_35_MHZ 2 +#define NETSEC_GMAC_GAR_REG_CR_35_60_MHZ 3 +#define NETSEC_GMAC_GAR_REG_CR_60_100_MHZ 0 +#define NETSEC_GMAC_GAR_REG_CR_100_150_MHZ 1 +#define NETSEC_GMAC_GAR_REG_CR_150_250_MHZ 4 +#define NETSEC_GMAC_GAR_REG_CR_250_300_MHZ 5 + +#define NETSEC_GMAC_RDLAR_REG_COMMON 0x18000 +#define NETSEC_GMAC_TDLAR_REG_COMMON 0x1c000 + +#define NETSEC_REG_NETSEC_VER_F_TAIKI 0x50000 + +#define NETSEC_REG_DESC_RING_CONFIG_CFG_UP BIT(31) +#define NETSEC_REG_DESC_RING_CONFIG_CH_RST BIT(30) +#define NETSEC_REG_DESC_TMR_MODE 4 +#define NETSEC_REG_DESC_ENDIAN 0 + +#define NETSEC_MAC_DESC_SOFT_RST_SOFT_RST 1 +#define NETSEC_MAC_DESC_INIT_REG_INIT 1 + +#define NETSEC_EEPROM_MAC_ADDRESS 0x00 +#define NETSEC_EEPROM_HM_ME_ADDRESS_H 0x08 +#define NETSEC_EEPROM_HM_ME_ADDRESS_L 0x0C +#define NETSEC_EEPROM_HM_ME_SIZE 0x10 +#define NETSEC_EEPROM_MH_ME_ADDRESS_H 0x14 +#define NETSEC_EEPROM_MH_ME_ADDRESS_L 0x18 +#define NETSEC_EEPROM_MH_ME_SIZE 0x1C +#define NETSEC_EEPROM_PKT_ME_ADDRESS 0x20 +#define NETSEC_EEPROM_PKT_ME_SIZE 0x24 + +#define DESC_SZ sizeof(struct netsec_de) + +#define NETSEC_F_NETSEC_VER_MAJOR_NUM (x) ((x) & 0xffff0000) + +#define EERPROM_MAP_OFFSET 0x8000000 +#define NOR_BLOCK 1024 + +struct netsec_de {/* Netsec Descriptor layout */ +u32 attr; +u32 data_buf_addr_up; +u32 data_buf_addr_lw; +u32 buf_len_info; +}; + +struct netsec_priv { +struct netsec_de rxde[PKTBUFSRX ]; +struct netsec_de txde[1 ]; +u16 rxat; + +phys_addr_t eeprom_base; +phys_addr_t ioaddr; + +struct mii_dev *bus; +struct phy_device *phydev; +u32 phy_addr, freq; +int phy_mode; +int max_speed; +}; + +struct netsec_tx_pkt_ctrl { +u16 tcp_seg_len; +bool tcp_seg_offload_flag; +bool cksum_offload_flag; +}; + +struct netsec_rx_pkt_info { +int rx_cksum_result; +int err_code; +bool err_flag; +}; + +static void netsec_write_reg (struct netsec_priv *priv,u32 reg_addr,u32 val) +{ +writel (val, priv->ioaddr + reg_addr); +} + +static u32 netsec_read_reg (struct netsec_priv *priv,u32 reg_addr) +{ +return readl (priv->ioaddr + reg_addr); +} + +/************* MDIO BUS OPS FOLLOW *************/ + +#define TIMEOUT_SPINS_MAC 1000 +#define TIMEOUT_SECONDARY_MS_MAC 100 + +static u32 netsec_clk_type (u32 freq) +{ +if (freq <MHZ (35 )) +return NETSEC_GMAC_GAR_REG_CR_25_35_MHZ ; +if (freq <MHZ (60 )) +return NETSEC_GMAC_GAR_REG_CR_35_60_MHZ ; +if (freq <MHZ (100 )) +return NETSEC_GMAC_GAR_REG_CR_60_100_MHZ ; +if (freq <MHZ (150 )) +return NETSEC_GMAC_GAR_REG_CR_100_150_MHZ ; +if (freq <MHZ (250 )) +return NETSEC_GMAC_GAR_REG_CR_150_250_MHZ ; + +return NETSEC_GMAC_GAR_REG_CR_250_300_MHZ ; +} + +static int netsec_wait_while_busy (struct netsec_priv *priv,u32 addr,u32 mask) +{ +u32 timeout =TIMEOUT_SPINS_MAC ; + +while (--timeout &&netsec_read_reg (priv, addr) & mask) +cpu_relax (); +if (timeout) +return 0 ; + + timeout =TIMEOUT_SECONDARY_MS_MAC ; +while (--timeout &&netsec_read_reg (priv, addr) & mask) +udelay (2000 ); + +if (timeout) +return 0 ; + +pr_err ("%s: timeout\n" , __func__); + +return -ETIMEDOUT ; +} + +static int netsec_set_mac_reg (struct netsec_priv *priv,u32 addr,u32 value) +{ +netsec_write_reg (priv,MAC_REG_DATA , value); +netsec_write_reg (priv,MAC_REG_CMD , addr |NETSEC_GMAC_CMD_ST_WRITE ); +return netsec_wait_while_busy (priv, +MAC_REG_CMD ,NETSEC_GMAC_CMD_ST_BUSY ); +} + +static int netsec_get_mac_reg (struct netsec_priv *priv,u32 addr,u32 *read) +{ +int ret; + +netsec_write_reg (priv,MAC_REG_CMD , addr |NETSEC_GMAC_CMD_ST_READ ); + ret =netsec_wait_while_busy (priv, +MAC_REG_CMD ,NETSEC_GMAC_CMD_ST_BUSY ); +if (ret) +return ret; + + *read =netsec_read_reg (priv,MAC_REG_DATA ); + +return 0 ; +} + +static int netsec_mac_wait_while_busy (struct netsec_priv *priv, +u32 addr,u32 mask) +{ +u32 timeout =TIMEOUT_SPINS_MAC ; +u32 data; +int ret; + +do { + ret =netsec_get_mac_reg (priv, addr, &data); +if (ret) +break ; +udelay (1 ); + }while (--timeout && (data & mask)); + +if (timeout) +return 0 ; + + timeout =TIMEOUT_SECONDARY_MS_MAC ; +do { +udelay (2000 ); + + ret =netsec_get_mac_reg (priv, addr, &data); +if (ret) +break ; +cpu_relax (); + }while (--timeout && (data & mask)); + +if (timeout && !ret) +return 0 ; + +return -ETIMEDOUT ; +} + +static void netsec_cache_invalidate (uintptr_t vaddr,int len) +{ +invalidate_dcache_range (rounddown (vaddr,ARCH_DMA_MINALIGN ), +roundup (vaddr + len,ARCH_DMA_MINALIGN )); +} + +static void netsec_cache_flush (uintptr_t vaddr,int len) +{ +flush_dcache_range (rounddown (vaddr,ARCH_DMA_MINALIGN ), +roundup (vaddr + len,ARCH_DMA_MINALIGN )); +} + +static void netsec_set_rx_de (struct netsec_priv *priv,u16 idx,void *addr) +{ +struct netsec_de *de = &priv->rxde[idx]; +u32 attr = (1 <<NETSEC_RX_PKT_OWN_FIELD ) | + (1 <<NETSEC_RX_PKT_FS_FIELD ) | + (1 <<NETSEC_RX_PKT_LS_FIELD ); + +if (idx ==PKTBUFSRX -1 ) + attr |= (1 <<NETSEC_RX_PKT_LD_FIELD ); + + de->data_buf_addr_up =upper_32_bits ((dma_addr_t )addr); + de->data_buf_addr_lw =lower_32_bits ((dma_addr_t )addr); + de->buf_len_info =PKTSIZE ; + de->attr = attr; +dmb (); +netsec_cache_flush ((uintptr_t )de,sizeof (*de)); +} + +static void netsec_set_tx_de (struct netsec_priv *priv,void *addr,int len) +{ +struct netsec_de *de = &priv->txde[0 ]; +u32 attr; + + attr = (1 <<NETSEC_TX_SHIFT_OWN_FIELD ) | + (1 <<NETSEC_TX_SHIFT_PT_FIELD ) | + (NETSEC_RING_GMAC <<NETSEC_TX_SHIFT_TDRID_FIELD ) | + (1 <<NETSEC_TX_SHIFT_FS_FIELD ) | + (1 <<NETSEC_TX_LAST ) | + (1 <<NETSEC_TX_SHIFT_TRS_FIELD ) | + (1 <<NETSEC_TX_SHIFT_LD_FIELD ); + + de->data_buf_addr_up =upper_32_bits ((dma_addr_t )addr); + de->data_buf_addr_lw =lower_32_bits ((dma_addr_t )addr); + de->buf_len_info = len; + de->attr = attr; +dmb (); +netsec_cache_flush ((uintptr_t )de,sizeof (*de)); +} + +static int netsec_get_phy_reg (struct netsec_priv *priv, +int phy_addr,int reg_addr) +{ +u32 data; +int ret; + +if (phy_addr !=7 ) +return -EINVAL ; + +if (netsec_set_mac_reg (priv,GMAC_REG_GAR ,NETSEC_GMAC_GAR_REG_GB | + phy_addr <<NETSEC_GMAC_GAR_REG_SHIFT_PA | + reg_addr <<NETSEC_GMAC_GAR_REG_SHIFT_GR | + (netsec_clk_type (priv->freq) << +GMAC_REG_SHIFT_CR_GAR ))) +return -ETIMEDOUT ; + + ret =netsec_mac_wait_while_busy (priv,GMAC_REG_GAR , +NETSEC_GMAC_GAR_REG_GB ); +if (ret) +return ret; + + ret =netsec_get_mac_reg (priv,GMAC_REG_GDR , &data); +if (ret) +return ret; + +return data; +} + +static int netsec_set_phy_reg (struct netsec_priv *priv, +int phy_addr,int reg_addr,u16 val) +{ +int ret; + +if (phy_addr !=7 ) +return -EINVAL ; +if (netsec_set_mac_reg (priv,GMAC_REG_GDR , val)) +return -ETIMEDOUT ; + +if (netsec_set_mac_reg (priv,GMAC_REG_GAR , + phy_addr <<NETSEC_GMAC_GAR_REG_SHIFT_PA | + reg_addr <<NETSEC_GMAC_GAR_REG_SHIFT_GR | +NETSEC_GMAC_GAR_REG_GW |NETSEC_GMAC_GAR_REG_GB | + (netsec_clk_type (priv->freq) << +GMAC_REG_SHIFT_CR_GAR ))) +return -ETIMEDOUT ; + + ret =netsec_mac_wait_while_busy (priv,GMAC_REG_GAR , +NETSEC_GMAC_GAR_REG_GB ); + +/* Developerbox implements RTL8211E PHY and there is +* a compatibility problem with F_GMAC4. +* RTL8211E expects MDC clock must be kept toggling for several +* clock cycle with MDIO high before entering the IDLE state. +* To meet this requirement, netsec driver needs to issue dummy +* read(e.g. read PHYID1(offset 0x2) register) right after write. +*/ +netsec_get_phy_reg (priv, phy_addr,MII_PHYSID1 ); + +return ret; +} + +static int netsec_mac_update_to_phy_state (struct netsec_priv *priv) +{ +struct phy_device *phydev = priv->phydev; +u32 value =0 ; + + value = phydev->duplex ?NETSEC_GMAC_MCR_REG_FULL_DUPLEX_COMMON : +NETSEC_GMAC_MCR_REG_HALF_DUPLEX_COMMON ; + +if (phydev->speed !=SPEED_1000 ) + value |=NETSEC_MCR_PS ; + +if (phydev->interface !=PHY_INTERFACE_MODE_GMII && + phydev->speed ==SPEED_100 ) + value |=NETSEC_GMAC_MCR_REG_FES ; + + value |=NETSEC_GMAC_MCR_REG_CST |NETSEC_GMAC_MCR_REG_JE ; + +if (phy_interface_is_rgmii (phydev)) + value |=NETSEC_GMAC_MCR_REG_IBN ; + +if (netsec_set_mac_reg (priv,GMAC_REG_MCR , value)) +return -ETIMEDOUT ; + +return 0 ; +} + +static int netsec_start_gmac (struct netsec_priv *priv) +{ +u32 value =0 ; +int ret; + +if (priv->max_speed !=SPEED_1000 ) + value = (NETSEC_GMAC_MCR_REG_CST | +NETSEC_GMAC_MCR_REG_HALF_DUPLEX_COMMON ); + +if (netsec_set_mac_reg (priv,GMAC_REG_MCR , value)) +return -ETIMEDOUT ; + +if (netsec_set_mac_reg (priv,GMAC_REG_BMR , +NETSEC_GMAC_BMR_REG_RESET )) +return -ETIMEDOUT ; + +/* Wait soft reset */ +mdelay (5 ); + + ret =netsec_get_mac_reg (priv,GMAC_REG_BMR , &value); +if (ret) +return ret; + +if (value &NETSEC_GMAC_BMR_REG_SWR ) +return -EAGAIN ; + +netsec_write_reg (priv,MAC_REG_DESC_SOFT_RST ,1 ); +if (netsec_wait_while_busy (priv,MAC_REG_DESC_SOFT_RST ,1 )) +return -ETIMEDOUT ; + +netsec_write_reg (priv,MAC_REG_DESC_INIT ,1 ); +if (netsec_wait_while_busy (priv,MAC_REG_DESC_INIT ,1 )) +return -ETIMEDOUT ; + +if (netsec_set_mac_reg (priv,GMAC_REG_BMR , +NETSEC_GMAC_BMR_REG_COMMON )) +return -ETIMEDOUT ; + +if (netsec_set_mac_reg (priv,GMAC_REG_RDLAR , +NETSEC_GMAC_RDLAR_REG_COMMON )) +return -ETIMEDOUT ; + +if (netsec_set_mac_reg (priv,GMAC_REG_TDLAR , +NETSEC_GMAC_TDLAR_REG_COMMON )) +return -ETIMEDOUT ; + +if (netsec_set_mac_reg (priv,GMAC_REG_MFFR ,0x80000001 )) +return -ETIMEDOUT ; + + ret =netsec_mac_update_to_phy_state (priv); +if (ret) +return ret; + + ret =netsec_get_mac_reg (priv,GMAC_REG_OMR , &value); +if (ret) +return ret; + + value |=NETSEC_GMAC_OMR_REG_SR ; + value |=NETSEC_GMAC_OMR_REG_ST ; + +netsec_write_reg (priv,NETSEC_REG_NRM_RX_INTEN_CLR , ~0 ); +netsec_write_reg (priv,NETSEC_REG_NRM_TX_INTEN_CLR , ~0 ); + +if (netsec_set_mac_reg (priv,GMAC_REG_OMR , value)) +return -ETIMEDOUT ; + +return 0 ; +} + +static int netsec_stop_gmac (struct netsec_priv *priv) +{ +u32 value; +int ret; + + ret =netsec_get_mac_reg (priv,GMAC_REG_OMR , &value); +if (ret) +return ret; + value &= ~NETSEC_GMAC_OMR_REG_SR ; + value &= ~NETSEC_GMAC_OMR_REG_ST ; + +/* disable all interrupts */ +netsec_write_reg (priv,NETSEC_REG_NRM_RX_INTEN_CLR , ~0 ); +netsec_write_reg (priv,NETSEC_REG_NRM_TX_INTEN_CLR , ~0 ); + +return netsec_set_mac_reg (priv,GMAC_REG_OMR , value); +} + +static void netsec_spi_read (char *buf,loff_t len,loff_t offset) +{ +struct udevice *new; +struct spi_flash *flash; + +spi_flash_probe_bus_cs (CONFIG_SF_DEFAULT_BUS ,CONFIG_SF_DEFAULT_CS , +CONFIG_SF_DEFAULT_SPEED ,CONFIG_SF_DEFAULT_MODE , &new); + flash =dev_get_uclass_priv (new); + +spi_flash_read (flash, offset, len, buf); +} + +static int netsec_read_rom_hwaddr (struct udevice *dev) +{ +struct netsec_priv *priv =dev_get_priv (dev); +struct eth_pdata *pdata =dev_get_plat (dev); +char macp[NOR_BLOCK ]; + +netsec_spi_read (macp,sizeof (macp), priv->eeprom_base); + + pdata->enetaddr[0 ] =readb (macp +3 ); + pdata->enetaddr[1 ] =readb (macp +2 ); + pdata->enetaddr[2 ] =readb (macp +1 ); + pdata->enetaddr[3 ] =readb (macp +0 ); + pdata->enetaddr[4 ] =readb (macp +7 ); + pdata->enetaddr[5 ] =readb (macp +6 ); +return 0 ; +} + +static int netsec_send (struct udevice *dev,void *packet,int length) +{ +struct netsec_priv *priv =dev_get_priv (dev); +u32 val, tout; + + val =netsec_read_reg (priv,NETSEC_REG_NRM_TX_STATUS ); +netsec_cache_flush ((uintptr_t )packet, length); +netsec_set_tx_de (priv, packet, length); +netsec_write_reg (priv,NETSEC_REG_NRM_TX_PKTCNT ,1 );/* submit another tx */ + + val =netsec_read_reg (priv,NETSEC_REG_NRM_TX_PKTCNT ); + + tout =10000 ; +do { + val =netsec_read_reg (priv,NETSEC_REG_NRM_TX_DONE_PKTCNT ); +udelay (2 ); + }while (--tout && !val); + +if (!tout) { + val =netsec_read_reg (priv,NETSEC_REG_NRM_TX_PKTCNT ); +pr_err ("%s: ETIMEDOUT: %dpackets\n" , __func__, val); +return -ETIMEDOUT ; + } + +return 0 ; +} + +static int netsec_free_packet (struct udevice *dev,uchar *packet,int length) +{ +struct netsec_priv *priv =dev_get_priv (dev); + +netsec_set_rx_de (priv, priv->rxat, net_rx_packets[priv->rxat]); + + priv->rxat++; +if (priv->rxat ==PKTBUFSRX ) + priv->rxat =0 ; + +return 0 ; +} + +static int netsec_recv (struct udevice *dev,int flags,uchar **packetp) +{ +struct netsec_priv *priv =dev_get_priv (dev); +int idx = priv->rxat; +uchar *ptr = net_rx_packets[idx]; +struct netsec_de *de = &priv->rxde[idx]; +int length =0 ; + +netsec_cache_invalidate ((uintptr_t )de,sizeof (*de)); + +if (de->attr & (1U <<NETSEC_RX_PKT_OWN_FIELD )) +return -EAGAIN ; + + length = de->buf_len_info >>16 ; + +/* invalidate after DMA is done */ +netsec_cache_invalidate ((uintptr_t )ptr, length); + *packetp = ptr; + +return length; +} + +static int _netsec_get_phy_reg (struct mii_dev *bus, +int phy_addr,int devad,int reg_addr) +{ +return netsec_get_phy_reg (bus->priv, phy_addr, reg_addr); +} + +static int _netsec_set_phy_reg (struct mii_dev *bus, +int phy_addr,int devad,int reg_addr,u16 val) +{ +return netsec_set_phy_reg (bus->priv, phy_addr, reg_addr, val); +} + +static int netsec_mdiobus_init (struct netsec_priv *priv,const char *name) +{ +struct mii_dev *bus =mdio_alloc (); + +if (!bus) +return -ENOMEM ; + + bus->read = _netsec_get_phy_reg; + bus->write = _netsec_set_phy_reg; +snprintf (bus->name,sizeof (bus->name),"%s" , name); + bus->priv = priv; + +return mdio_register (bus); +} + +static int netsec_phy_init (struct netsec_priv *priv,void *dev) +{ +struct phy_device *phydev; +int ret; + + phydev =phy_connect (priv->bus, priv->phy_addr, dev, priv->phy_mode); + + phydev->supported &=PHY_GBIT_FEATURES ; +if (priv->max_speed) { + ret =phy_set_supported (phydev, priv->max_speed); +if (ret) +return ret; + } + phydev->advertising = phydev->supported; + + priv->phydev = phydev; +phy_config (phydev); + +return 0 ; +} + +static int netsec_netdev_load_ucode_region (struct netsec_priv *priv,u32 reg, +u32 addr_h,u32 addr_l,u32 size) +{ +u64 base = ((u64 )addr_h <<32 | addr_l) -EERPROM_MAP_OFFSET ; + +while (size >0 ) { +char buf[NOR_BLOCK ]; +u32 *ucode = (u32 *)buf; +u64 off; +int i; + + off = base %NOR_BLOCK ; + base -= off; +netsec_spi_read (buf,sizeof (buf), base); + +for (i = off /4 ; i <sizeof (buf) /4 && size >0 ; i++, size--) +netsec_write_reg (priv, reg, ucode[i]); + base +=NOR_BLOCK ; + } + +return 0 ; +} + +static int netsec_netdev_load_microcode (struct netsec_priv *priv) +{ +u32 addr_h, addr_l, size; +char buf[NOR_BLOCK ]; +u32 *ucinfo = (u32 *)buf; +int err; + +netsec_spi_read (buf,sizeof (buf), priv->eeprom_base); + + addr_h = ucinfo[NETSEC_EEPROM_HM_ME_ADDRESS_H >>2 ]; + addr_l = ucinfo[NETSEC_EEPROM_HM_ME_ADDRESS_L >>2 ]; + size = ucinfo[NETSEC_EEPROM_HM_ME_SIZE >>2 ]; + + err =netsec_netdev_load_ucode_region (priv,NETSEC_REG_DMAC_HM_CMD_BUF , + addr_h, addr_l, size); +if (err) +return err; + + addr_h = ucinfo[NETSEC_EEPROM_MH_ME_ADDRESS_H >>2 ]; + addr_l = ucinfo[NETSEC_EEPROM_MH_ME_ADDRESS_L >>2 ]; + size = ucinfo[NETSEC_EEPROM_MH_ME_SIZE >>2 ]; + + err =netsec_netdev_load_ucode_region (priv,NETSEC_REG_DMAC_MH_CMD_BUF , + addr_h, addr_l, size); +if (err) +return err; + + addr_h =0 ; + addr_l = ucinfo[NETSEC_EEPROM_PKT_ME_ADDRESS >>2 ]; + size = ucinfo[NETSEC_EEPROM_PKT_ME_SIZE >>2 ]; + + err =netsec_netdev_load_ucode_region (priv,NETSEC_REG_PKT_CMD_BUF , + addr_h, addr_l, size); +if (err) +return err; + +return 0 ; +} + +void netsec_pre_init_microengine (struct netsec_priv *priv) +{ +u32 data; + +/* Remove dormant settings */ + data =netsec_get_phy_reg (priv, priv->phy_addr,MII_BMCR ); + data &= ~BMCR_PDOWN ; + data |=BMCR_ISOLATE ; +netsec_set_phy_reg (priv, priv->phy_addr,MII_BMCR , data); +mdelay (100 ); + +/* Put phy in loopback mode to guarantee RXCLK input */ + data |=BMCR_LOOPBACK ; +netsec_set_phy_reg (priv, priv->phy_addr,MII_BMCR , data); +mdelay (100 ); +} + +void netsec_post_init_microengine (struct netsec_priv *priv) +{ +u32 data; + +/* Get phy back to normal operation */ + data =netsec_get_phy_reg (priv, priv->phy_addr,MII_BMCR ); + data &= ~BMCR_LOOPBACK ; +netsec_set_phy_reg (priv, priv->phy_addr,MII_BMCR , data); +mdelay (100 ); + +/* Apply software reset */ + data |=BMCR_RESET ; +netsec_set_phy_reg (priv, priv->phy_addr,MII_BMCR , data); +mdelay (100 ); +} + +static int netsec_reset_hardware (struct netsec_priv *priv,bool load_ucode) +{ +u32 value; +int err; + +netsec_write_reg (priv,NETSEC_REG_CLK_EN ,0x24 ); + +/* stop DMA engines */ +if (!netsec_read_reg (priv,NETSEC_REG_ADDR_DIS_CORE )) { +netsec_write_reg (priv,NETSEC_REG_DMA_HM_CTRL , +NETSEC_DMA_CTRL_REG_STOP ); +netsec_write_reg (priv,NETSEC_REG_DMA_MH_CTRL , +NETSEC_DMA_CTRL_REG_STOP ); + + value =100 ; +while (netsec_read_reg (priv,NETSEC_REG_DMA_HM_CTRL ) & +NETSEC_DMA_CTRL_REG_STOP ) { +udelay (1000 ); +if (--value ==0 ) { +pr_err ("%s:%d timeout!\n" , __func__, __LINE__); +break ; + } + } + + value =100 ; +while (netsec_read_reg (priv,NETSEC_REG_DMA_MH_CTRL ) & +NETSEC_DMA_CTRL_REG_STOP ) { +udelay (1000 ); +if (--value ==0 ) { +pr_err ("%s:%d timeout!\n" , __func__, __LINE__); +break ; + } + } + } + +netsec_set_mac_reg (priv,GMAC_REG_BMR ,NETSEC_GMAC_BMR_REG_RESET ); + +netsec_write_reg (priv,NETSEC_REG_SOFT_RST ,NETSEC_SOFT_RST_REG_RESET ); +netsec_write_reg (priv,NETSEC_REG_SOFT_RST ,NETSEC_SOFT_RST_REG_RUN ); +netsec_write_reg (priv,NETSEC_REG_COM_INIT ,NETSEC_COM_INIT_REG_ALL ); + + value =100 ; +while (netsec_read_reg (priv,NETSEC_REG_COM_INIT ) !=0 ) { +udelay (1000 ); +if (--value ==0 ) { +pr_err ("%s:%d COM_INIT timeout!\n" , __func__, __LINE__); +break ; + } + } + +/* MAC desc init */ +netsec_write_reg (priv,MAC_REG_DESC_INIT ,1 ); +netsec_wait_while_busy (priv,MAC_REG_DESC_INIT ,1 ); +/* set MAC_INTF_SEL */ +netsec_write_reg (priv,MAC_REG_INTF_SEL ,1 ); + +netsec_write_reg (priv,NETSEC_REG_CLK_EN ,1 <<5 ); + +/* set desc_start addr */ +netsec_write_reg (priv,NETSEC_REG_NRM_RX_DESC_START_UP , +upper_32_bits ((dma_addr_t )priv->rxde)); +netsec_write_reg (priv,NETSEC_REG_NRM_RX_DESC_START_LW , +lower_32_bits ((dma_addr_t )priv->rxde)); + +netsec_write_reg (priv,NETSEC_REG_NRM_TX_DESC_START_UP , +upper_32_bits ((dma_addr_t )priv->txde)); +netsec_write_reg (priv,NETSEC_REG_NRM_TX_DESC_START_LW , +lower_32_bits ((dma_addr_t )priv->txde)); + +/* set normal tx dring ring config */ +netsec_write_reg (priv,NETSEC_REG_NRM_TX_CONFIG , +1 <<NETSEC_REG_DESC_ENDIAN ); +netsec_write_reg (priv,NETSEC_REG_NRM_RX_CONFIG , +1 <<NETSEC_REG_DESC_ENDIAN ); + +if (load_ucode) { + err =netsec_netdev_load_microcode (priv); +if (err) { +pr_err ("%s: failed to load microcode (%d)\n" , + __func__, err); +return err; + } + } + +/* set desc_start addr */ +netsec_write_reg (priv,NETSEC_REG_NRM_RX_DESC_START_UP , +upper_32_bits ((dma_addr_t )priv->rxde)); +netsec_write_reg (priv,NETSEC_REG_NRM_RX_DESC_START_LW , +lower_32_bits ((dma_addr_t )priv->rxde)); + +netsec_write_reg (priv,NETSEC_REG_NRM_TX_DESC_START_UP , +upper_32_bits ((dma_addr_t )priv->txde)); +netsec_write_reg (priv,NETSEC_REG_NRM_TX_DESC_START_LW , +lower_32_bits ((dma_addr_t )priv->txde)); + +netsec_write_reg (priv,NETSEC_REG_CLK_EN ,1 <<5 ); + +/* start DMA engines */ +netsec_write_reg (priv,NETSEC_REG_DMA_TMR_CTRL , priv->freq /1000000 -1 ); + +netsec_pre_init_microengine (priv); + +netsec_write_reg (priv,NETSEC_REG_ADDR_DIS_CORE ,0 ); + +mdelay (100 ); + +if (!(netsec_read_reg (priv,NETSEC_REG_TOP_STATUS ) & +NETSEC_TOP_IRQ_REG_ME_START )) { +pr_err ("microengine start failed\n" ); +return -ENXIO ; + } + +netsec_post_init_microengine (priv); + +/* clear microcode load end status */ +netsec_write_reg (priv,NETSEC_REG_TOP_STATUS , +NETSEC_TOP_IRQ_REG_ME_START ); + +netsec_write_reg (priv,NETSEC_REG_CLK_EN ,1 <<5 ); + + value =netsec_read_reg (priv,NETSEC_REG_PKT_CTRL ); + value |=NETSEC_PKT_CTRL_REG_MODE_NRM ; +/* change to normal mode */ +netsec_write_reg (priv,NETSEC_REG_DMA_MH_CTRL ,MH_CTRL__MODE_TRANS ); +netsec_write_reg (priv,NETSEC_REG_PKT_CTRL , value); + + value =100 ; +while ((netsec_read_reg (priv,NETSEC_REG_MODE_TRANS_COMP_STATUS ) & +NETSEC_MODE_TRANS_COMP_IRQ_T2N ) ==0 ) { +udelay (1000 ); +if (--value ==0 ) { + value =netsec_read_reg (priv,NETSEC_REG_MODE_TRANS_COMP_STATUS ); +pr_err ("%s:%d timeout! val=%x\n" , __func__, __LINE__, value); +break ; + } + } + +/* clear any pending EMPTY/ERR irq status */ +netsec_write_reg (priv,NETSEC_REG_NRM_TX_STATUS , ~0 ); + +/* Disable TX & RX intr */ +netsec_write_reg (priv,NETSEC_REG_INTEN_CLR , ~0 ); + +return 0 ; +} + +static void netsec_stop (struct udevice *dev) +{ +struct netsec_priv *priv =dev_get_priv (dev); + +netsec_write_reg (priv,NETSEC_REG_ADDR_DIS_CORE ,7 ); +netsec_stop_gmac (priv); +phy_shutdown (priv->phydev); +netsec_reset_hardware (priv, false); +} + +static int netsec_start (struct udevice *dev) +{ +struct netsec_priv *priv =dev_get_priv (dev); +int i; + +phy_startup (priv->phydev); +netsec_start_gmac (priv); + + priv->rxat =0 ; +for (i =0 ; i <PKTBUFSRX ; i++) +netsec_set_rx_de (priv, i, net_rx_packets[i]); + +return 0 ; +} + +static int netsec_of_to_plat (struct udevice *dev) +{ +struct eth_pdata *pdata =dev_get_plat (dev); +struct netsec_priv *priv =dev_get_priv (dev); +struct ofnode_phandle_args phandle_args; +const char *phy_mode; + + pdata->iobase =dev_read_addr_index (dev,0 ); + priv->eeprom_base =dev_read_addr_index (dev,1 ) -EERPROM_MAP_OFFSET ; + + pdata->phy_interface =-1 ; + phy_mode =dev_read_prop (dev,"phy-mode" ,NULL ); +if (phy_mode) + pdata->phy_interface =phy_get_interface_by_name (phy_mode); +if (pdata->phy_interface ==-1 ) { +pr_err ("%s: Invalid PHY interface '%s'\n" , __func__, phy_mode); +return -EINVAL ; + } + +if (!dev_read_phandle_with_args (dev,"phy-handle" ,NULL ,0 ,0 , + &phandle_args)) + priv->phy_addr =ofnode_read_u32_default (phandle_args.node,"reg" ,7 ); +else + priv->phy_addr =7 ; + + pdata->max_speed =dev_read_u32_default (dev,"max-speed" ,SPEED_1000 ); + + priv->ioaddr = pdata->iobase; + priv->phy_mode = pdata->phy_interface; + priv->max_speed = pdata->max_speed; + priv->freq =250000000UL ; + +return 0 ; +} + +#define SMMU_SCR0_SHCFG_INNER (0x2 << 22) +#define SMMU_SCR0_MTCFG (0x1 << 20) +#define SMMU_SCR0_MEMATTR_INNER_OUTER_WB (0xf << 16) + +static int netsec_probe (struct udevice *dev) +{ +struct netsec_priv *priv =dev_get_priv (dev); +int ret; + +writel (SMMU_SCR0_SHCFG_INNER |SMMU_SCR0_MTCFG |SMMU_SCR0_MEMATTR_INNER_OUTER_WB , + (phys_addr_t )0x52E00000 ); + +netsec_reset_hardware (priv, true); + + ret =netsec_mdiobus_init (priv, dev->name); +if (ret) { +pr_err ("Failed to initialize mdiobus: %d\n" , ret); +return ret; + } + + priv->bus =miiphy_get_dev_by_name (dev->name); + + ret =netsec_phy_init (priv, dev); +if (ret) { +pr_err ("Failed to initialize phy: %d\n" , ret); + goto out_mdiobus_release; + } + +return 0 ; +out_mdiobus_release: +mdio_unregister (priv->bus); +mdio_free (priv->bus); +return ret; +} + +static int netsec_remove (struct udevice *dev) +{ +struct netsec_priv *priv =dev_get_priv (dev); + +free (priv->phydev); +mdio_unregister (priv->bus); +mdio_free (priv->bus); + +return 0 ; +} + +static const struct eth_ops netsec_ops = { + .start = netsec_start, + .stop = netsec_stop, + .send = netsec_send, + .recv = netsec_recv, + .free_pkt = netsec_free_packet, + .read_rom_hwaddr = netsec_read_rom_hwaddr, +}; + +static const struct udevice_id netsec_ids[] = { + { + .compatible ="socionext,synquacer-netsec" , + }, + {} +}; + +U_BOOT_DRIVER (ave) = {
drivers/net/sni_netsec.c line 1134
Quoted 10 lines
drivers/net/sni_netsec.c new file +10
-0+ .name = "synquacer_netsec", + .id = UCLASS_ETH, + .of_match = netsec_ids, + .probe = netsec_probe, + .remove = netsec_remove, + .of_to_plat = netsec_of_to_plat, + .ops = &netsec_ops, + .priv_auto = sizeof(struct netsec_priv), + .plat_auto = sizeof(struct eth_pdata), +};
Re: [PATCH v5 08/13] net: synquacer: Add netsec driver
In reply to Masami HiramatsuQuoted 1,192 lines · Masami Hiramatsu
From: Jassi Brar <[email protected]>
Add SynQuacer's NETSEC GbE controller driver. Since this driver will load the firmware from SPI NOR flash, this depends on
CONFIG_SYNQUACER_SPI=y.Signed-off-by Jassi Brar <[email protected]>---
drivers/net/Kconfig| 8drivers/net/Makefile| 1drivers/net/sni_netsec.c| 1134
++++++++++++++++++++++++++++++++++++++++++++++3 files changed, 1143 insertions(+)create mode 100644
drivers/net/sni_netsec.cdrivers/net/Kconfig +0
-0@@ -673,6 +673,14 @@ config SNI_AVEThis driver implements support for the Socionext AVE Ethernet controller, as found on the Socionext UniPhier family.
drivers/net/Kconfig +8
-0+config SNI_NETSEC + bool "Socionext NETSEC Ethernet support" + depends on DM_ETH && SYNQUACER_SPI + select PHYLIB + help + This driver implements support for the Socionext SynQuacer NETSEC + ethernet controller, as found on the Socionext SynQuacer family. +source "
drivers/net/mscc_eswitch/Kconfig"config
ETHER_ON_FEC1drivers/net/Makefile +0
-0@@ -89,6 +89,7 @@ obj-$(CONFIG_DWC_ETH_QOS) += dwc_eth_qos.oobj-$(CONFIG_FSL_PFE) += pfe_eth/
obj-y += qe/
obj-$(CONFIG_SNI_AVE) += sni_ave.o
+obj-$(CONFIG_SNI_NETSEC) += sni_netsec.o
obj-y += ti/
obj-$(CONFIG_MEDIATEK_ETH) += mtk_eth.o
obj-y += mscc_eswitch/drivers/net/sni_netsec.c new file +289
-0@@ -0,0 +1,1134 @@ +// SPDX-License-Identifier: GPL-2.0+ +/** +* netsec.c - Socionext Synquacer Netsec driver +* Copyright 2021 Linaro Ltd. +*/ + +#include <clk.h> +#include <cpu_func.h> +#include <dm.h> +#include <fdt_support.h> +#include <log.h> +#include <malloc.h> +#include <miiphy.h> +#include <net.h> +#include <regmap.h> +#include <reset.h> +#include <syscon.h> +#include <asm/cache.h> +#include <asm/global_data.h> +#include <dm/device_compat.h> +#include <linux/bitops.h> +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/iopoll.h> +#include <spi.h> +#include <spi_flash.h> + +#define NETSEC_REG_SOFT_RST 0x104 +#define NETSEC_REG_COM_INIT 0x120 + +#define NETSEC_REG_TOP_STATUS 0x200 +#define NETSEC_IRQ_RX BIT(1) +#define NETSEC_IRQ_TX BIT(0) + +#define NETSEC_REG_TOP_INTEN 0x204 +#define NETSEC_REG_INTEN_SET 0x234 +#define NETSEC_REG_INTEN_CLR 0x238 + +#define NETSEC_REG_NRM_TX_STATUS 0x400 +#define NETSEC_REG_NRM_TX_INTEN 0x404 +#define NETSEC_REG_NRM_TX_INTEN_SET 0x428 +#define NETSEC_REG_NRM_TX_INTEN_CLR 0x42c +#define NRM_TX_ST_NTOWNR BIT(17) +#define NRM_TX_ST_TR_ERR BIT(16) +#define NRM_TX_ST_TXDONE BIT(15) +#define NRM_TX_ST_TMREXP BIT(14) + +#define NETSEC_REG_NRM_RX_STATUS 0x440 +#define NETSEC_REG_NRM_RX_INTEN 0x444 +#define NETSEC_REG_NRM_RX_INTEN_SET 0x468 +#define NETSEC_REG_NRM_RX_INTEN_CLR 0x46c +#define NRM_RX_ST_RC_ERR BIT(16) +#define NRM_RX_ST_PKTCNT BIT(15) +#define NRM_RX_ST_TMREXP BIT(14) + +#define NETSEC_REG_PKT_CMD_BUF 0xd0 + +#define NETSEC_REG_CLK_EN 0x100 + +#define NETSEC_REG_PKT_CTRL 0x140 + +#define NETSEC_REG_DMA_TMR_CTRL 0x20c +#define NETSEC_REG_F_TAIKI_MC_VER 0x22c +#define NETSEC_REG_F_TAIKI_VER 0x230 +#define NETSEC_REG_DMA_HM_CTRL 0x214 +#define NETSEC_REG_DMA_MH_CTRL 0x220 +#define NETSEC_REG_ADDR_DIS_CORE 0x218 +#define NETSEC_REG_DMAC_HM_CMD_BUF 0x210 +#define NETSEC_REG_DMAC_MH_CMD_BUF 0x21c + +#define NETSEC_REG_NRM_TX_PKTCNT 0x410 + +#define NETSEC_REG_NRM_TX_DONE_PKTCNT 0x414 +#define NETSEC_REG_NRM_TX_DONE_TXINT_PKTCNT 0x418 + +#define NETSEC_REG_NRM_TX_TMR 0x41c + +#define NETSEC_REG_NRM_RX_PKTCNT 0x454 +#define NETSEC_REG_NRM_RX_RXINT_PKTCNT 0x458 +#define NETSEC_REG_NRM_TX_TXINT_TMR 0x420 +#define NETSEC_REG_NRM_RX_RXINT_TMR 0x460 + +#define NETSEC_REG_NRM_RX_TMR 0x45c + +#define NETSEC_REG_NRM_TX_DESC_START_UP 0x434 +#define NETSEC_REG_NRM_TX_DESC_START_LW 0x408 +#define NETSEC_REG_NRM_RX_DESC_START_UP 0x474 +#define NETSEC_REG_NRM_RX_DESC_START_LW 0x448 + +#define NETSEC_REG_NRM_TX_CONFIG 0x430 +#define NETSEC_REG_NRM_RX_CONFIG 0x470 + +#define MAC_REG_STATUS 0x1024 +#define MAC_REG_DATA 0x11c0 +#define MAC_REG_CMD 0x11c4 +#define MAC_REG_FLOW_TH 0x11cc +#define MAC_REG_INTF_SEL 0x11d4 +#define MAC_REG_DESC_INIT 0x11fc +#define MAC_REG_DESC_SOFT_RST 0x1204 +#define NETSEC_REG_MODE_TRANS_COMP_STATUS 0x500 + +#define GMAC_REG_MCR 0x0000 +#define GMAC_REG_MFFR 0x0004 +#define GMAC_REG_GAR 0x0010 +#define GMAC_REG_GDR 0x0014 +#define GMAC_REG_FCR 0x0018 +#define GMAC_REG_BMR 0x1000 +#define GMAC_REG_RDLAR 0x100c +#define GMAC_REG_TDLAR 0x1010 +#define GMAC_REG_OMR 0x1018 + +#define MHZ (n) ((n) * 1000 * 1000) + +#define NETSEC_TX_SHIFT_OWN_FIELD 31 +#define NETSEC_TX_SHIFT_LD_FIELD 30 +#define NETSEC_TX_SHIFT_DRID_FIELD 24 +#define NETSEC_TX_SHIFT_PT_FIELD 21 +#define NETSEC_TX_SHIFT_TDRID_FIELD 16 +#define NETSEC_TX_SHIFT_CC_FIELD 15 +#define NETSEC_TX_SHIFT_FS_FIELD 9 +#define NETSEC_TX_LAST 8 +#define NETSEC_TX_SHIFT_CO 7 +#define NETSEC_TX_SHIFT_SO 6 +#define NETSEC_TX_SHIFT_TRS_FIELD 4 + +#define NETSEC_RX_PKT_OWN_FIELD 31 +#define NETSEC_RX_PKT_LD_FIELD 30 +#define NETSEC_RX_PKT_SDRID_FIELD 24 +#define NETSEC_RX_PKT_FR_FIELD 23 +#define NETSEC_RX_PKT_ER_FIELD 21 +#define NETSEC_RX_PKT_ERR_FIELD 16 +#define NETSEC_RX_PKT_TDRID_FIELD 12 +#define NETSEC_RX_PKT_FS_FIELD 9 +#define NETSEC_RX_PKT_LS_FIELD 8 +#define NETSEC_RX_PKT_CO_FIELD 6 + +#define NETSEC_RX_PKT_ERR_MASK 3 + +#define NETSEC_MAX_TX_PKT_LEN 1518 +#define NETSEC_MAX_TX_JUMBO_PKT_LEN 9018 + +#define NETSEC_RING_GMAC 15 +#define NETSEC_RING_MAX 2 + +#define NETSEC_TCP_SEG_LEN_MAX 1460 +#define NETSEC_TCP_JUMBO_SEG_LEN_MAX 8960 + +#define NETSEC_RX_CKSUM_NOTAVAIL 0 +#define NETSEC_RX_CKSUM_OK 1 +#define NETSEC_RX_CKSUM_NG 2 + +#define NETSEC_TOP_IRQ_REG_ME_START BIT(20) +#define NETSEC_IRQ_TRANSITION_COMPLETE BIT(4) + +#define NETSEC_MODE_TRANS_COMP_IRQ_N2T BIT(20) +#define NETSEC_MODE_TRANS_COMP_IRQ_T2N BIT(19) + +#define NETSEC_INT_PKTCNT_MAX 2047 + +#define NETSEC_FLOW_START_TH_MAX 95 +#define NETSEC_FLOW_STOP_TH_MAX 95 +#define NETSEC_FLOW_PAUSE_TIME_MIN 5 + +#define NETSEC_CLK_EN_REG_DOM_ALL 0x3f + +#define NETSEC_PKT_CTRL_REG_MODE_NRM BIT(28) +#define NETSEC_PKT_CTRL_REG_EN_JUMBO BIT(27) +#define NETSEC_PKT_CTRL_REG_LOG_CHKSUM_ER BIT(3) +#define NETSEC_PKT_CTRL_REG_LOG_HD_INCOMPLETE BIT(2) +#define NETSEC_PKT_CTRL_REG_LOG_HD_ER BIT(1) +#define NETSEC_PKT_CTRL_REG_DRP_NO_MATCH BIT(0) + +#define NETSEC_CLK_EN_REG_DOM_G BIT(5) +#define NETSEC_CLK_EN_REG_DOM_C BIT(1) +#define NETSEC_CLK_EN_REG_DOM_D BIT(0) + +#define NETSEC_COM_INIT_REG_DB BIT(2) +#define NETSEC_COM_INIT_REG_CLS BIT(1) +#define NETSEC_COM_INIT_REG_ALL (NETSEC_COM_INIT_REG_CLS | \ + NETSEC_COM_INIT_REG_DB) + +#define NETSEC_SOFT_RST_REG_RESET 0 +#define NETSEC_SOFT_RST_REG_RUN BIT(31) + +#define NETSEC_DMA_CTRL_REG_STOP 1 +#define MH_CTRL__MODE_TRANS BIT(20) + +#define NETSEC_GMAC_CMD_ST_READ 0 +#define NETSEC_GMAC_CMD_ST_WRITE BIT(28) +#define NETSEC_GMAC_CMD_ST_BUSY BIT(31) + +#define NETSEC_GMAC_BMR_REG_COMMON 0x00412080 +#define NETSEC_GMAC_BMR_REG_RESET 0x00020181 +#define NETSEC_GMAC_BMR_REG_SWR 0x00000001 + +#define NETSEC_GMAC_OMR_REG_ST BIT(13) +#define NETSEC_GMAC_OMR_REG_SR BIT(1) + +#define NETSEC_GMAC_MCR_REG_IBN BIT(30) +#define NETSEC_GMAC_MCR_REG_CST BIT(25) +#define NETSEC_GMAC_MCR_REG_JE BIT(20) +#define NETSEC_MCR_PS BIT(15) +#define NETSEC_GMAC_MCR_REG_FES BIT(14) +#define NETSEC_GMAC_MCR_REG_FULL_DUPLEX_COMMON 0x0000280c +#define NETSEC_GMAC_MCR_REG_HALF_DUPLEX_COMMON 0x0001a00c + +#define NETSEC_FCR_RFE BIT(2) +#define NETSEC_FCR_TFE BIT(1) + +#define NETSEC_GMAC_GAR_REG_GW BIT(1) +#define NETSEC_GMAC_GAR_REG_GB BIT(0) + +#define NETSEC_GMAC_GAR_REG_SHIFT_PA 11 +#define NETSEC_GMAC_GAR_REG_SHIFT_GR 6 +#define GMAC_REG_SHIFT_CR_GAR 2 + +#define NETSEC_GMAC_GAR_REG_CR_25_35_MHZ 2 +#define NETSEC_GMAC_GAR_REG_CR_35_60_MHZ 3 +#define NETSEC_GMAC_GAR_REG_CR_60_100_MHZ 0 +#define NETSEC_GMAC_GAR_REG_CR_100_150_MHZ 1 +#define NETSEC_GMAC_GAR_REG_CR_150_250_MHZ 4 +#define NETSEC_GMAC_GAR_REG_CR_250_300_MHZ 5 + +#define NETSEC_GMAC_RDLAR_REG_COMMON 0x18000 +#define NETSEC_GMAC_TDLAR_REG_COMMON 0x1c000 + +#define NETSEC_REG_NETSEC_VER_F_TAIKI 0x50000 + +#define NETSEC_REG_DESC_RING_CONFIG_CFG_UP BIT(31) +#define NETSEC_REG_DESC_RING_CONFIG_CH_RST BIT(30) +#define NETSEC_REG_DESC_TMR_MODE 4 +#define NETSEC_REG_DESC_ENDIAN 0 + +#define NETSEC_MAC_DESC_SOFT_RST_SOFT_RST 1 +#define NETSEC_MAC_DESC_INIT_REG_INIT 1 + +#define NETSEC_EEPROM_MAC_ADDRESS 0x00 +#define NETSEC_EEPROM_HM_ME_ADDRESS_H 0x08 +#define NETSEC_EEPROM_HM_ME_ADDRESS_L 0x0C +#define NETSEC_EEPROM_HM_ME_SIZE 0x10 +#define NETSEC_EEPROM_MH_ME_ADDRESS_H 0x14 +#define NETSEC_EEPROM_MH_ME_ADDRESS_L 0x18 +#define NETSEC_EEPROM_MH_ME_SIZE 0x1C +#define NETSEC_EEPROM_PKT_ME_ADDRESS 0x20 +#define NETSEC_EEPROM_PKT_ME_SIZE 0x24 + +#define DESC_SZ sizeof(struct netsec_de) + +#define NETSEC_F_NETSEC_VER_MAJOR_NUM (x) ((x) & 0xffff0000) + +#define EERPROM_MAP_OFFSET 0x8000000 +#define NOR_BLOCK 1024 + +struct netsec_de {/* Netsec Descriptor layout */ +u32 attr; +u32 data_buf_addr_up; +u32 data_buf_addr_lw; +u32 buf_len_info; +}; + +struct netsec_priv { +struct netsec_de rxde[PKTBUFSRX ]; +struct netsec_de txde[1 ]; +u16 rxat; + +phys_addr_t eeprom_base; +phys_addr_t ioaddr; + +struct mii_dev *bus; +struct phy_device *phydev; +u32 phy_addr, freq; +int phy_mode; +int max_speed; +}; + +struct netsec_tx_pkt_ctrl { +u16 tcp_seg_len; +bool tcp_seg_offload_flag; +bool cksum_offload_flag; +}; + +struct netsec_rx_pkt_info { +int rx_cksum_result; +int err_code; +bool err_flag; +}; + +static void netsec_write_reg(struct netsec_priv *priv, u32 reg_addr,u32 val)
drivers/net/sni_netsec.c new file +31
-0+{ +writel (val, priv->ioaddr + reg_addr); +} + +static u32 netsec_read_reg (struct netsec_priv *priv,u32 reg_addr) +{ +return readl (priv->ioaddr + reg_addr); +} + +/************* MDIO BUS OPS FOLLOW *************/ + +#define TIMEOUT_SPINS_MAC 1000 +#define TIMEOUT_SECONDARY_MS_MAC 100 + +static u32 netsec_clk_type (u32 freq) +{ +if (freq <MHZ (35 )) +return NETSEC_GMAC_GAR_REG_CR_25_35_MHZ ; +if (freq <MHZ (60 )) +return NETSEC_GMAC_GAR_REG_CR_35_60_MHZ ; +if (freq <MHZ (100 )) +return NETSEC_GMAC_GAR_REG_CR_60_100_MHZ ; +if (freq <MHZ (150 )) +return NETSEC_GMAC_GAR_REG_CR_100_150_MHZ ; +if (freq <MHZ (250 )) +return NETSEC_GMAC_GAR_REG_CR_150_250_MHZ ; + +return NETSEC_GMAC_GAR_REG_CR_250_300_MHZ ; +} + +static int netsec_wait_while_busy(struct netsec_priv *priv, u32 addr,u32 mask)
drivers/net/sni_netsec.c new file +21
-0+{ +u32 timeout =TIMEOUT_SPINS_MAC ; + +while (--timeout &&netsec_read_reg (priv, addr) & mask) +cpu_relax (); +if (timeout) +return 0 ; + + timeout =TIMEOUT_SECONDARY_MS_MAC ; +while (--timeout &&netsec_read_reg (priv, addr) & mask) +udelay (2000 ); + +if (timeout) +return 0 ; + +pr_err ("%s: timeout\n" , __func__); + +return -ETIMEDOUT ; +} + +static int netsec_set_mac_reg(struct netsec_priv *priv, u32 addr, u32value)
drivers/net/sni_netsec.c new file +8
-0+{ +netsec_write_reg (priv,MAC_REG_DATA , value); +netsec_write_reg (priv,MAC_REG_CMD , addr |NETSEC_GMAC_CMD_ST_WRITE ); +return netsec_wait_while_busy (priv, +MAC_REG_CMD ,NETSEC_GMAC_CMD_ST_BUSY ); +} + +static int netsec_get_mac_reg(struct netsec_priv *priv, u32 addr, u32*read)
drivers/net/sni_netsec.c new file +60
-0+{ +int ret; + +netsec_write_reg (priv,MAC_REG_CMD , addr |NETSEC_GMAC_CMD_ST_READ ); + ret =netsec_wait_while_busy (priv, +MAC_REG_CMD ,NETSEC_GMAC_CMD_ST_BUSY ); +if (ret) +return ret; + + *read =netsec_read_reg (priv,MAC_REG_DATA ); + +return 0 ; +} + +static int netsec_mac_wait_while_busy (struct netsec_priv *priv, +u32 addr,u32 mask) +{ +u32 timeout =TIMEOUT_SPINS_MAC ; +u32 data; +int ret; + +do { + ret =netsec_get_mac_reg (priv, addr, &data); +if (ret) +break ; +udelay (1 ); + }while (--timeout && (data & mask)); + +if (timeout) +return 0 ; + + timeout =TIMEOUT_SECONDARY_MS_MAC ; +do { +udelay (2000 ); + + ret =netsec_get_mac_reg (priv, addr, &data); +if (ret) +break ; +cpu_relax (); + }while (--timeout && (data & mask)); + +if (timeout && !ret) +return 0 ; + +return -ETIMEDOUT ; +} + +static void netsec_cache_invalidate (uintptr_t vaddr,int len) +{ +invalidate_dcache_range (rounddown (vaddr,ARCH_DMA_MINALIGN ), +roundup (vaddr + len,ARCH_DMA_MINALIGN )); +} + +static void netsec_cache_flush (uintptr_t vaddr,int len) +{ +flush_dcache_range (rounddown (vaddr,ARCH_DMA_MINALIGN ), +roundup (vaddr + len,ARCH_DMA_MINALIGN )); +} + +static void netsec_set_rx_de(struct netsec_priv *priv, u16 idx, void*addr)
drivers/net/sni_netsec.c new file +18
-0+{ +struct netsec_de *de = &priv->rxde[idx]; +u32 attr = (1 <<NETSEC_RX_PKT_OWN_FIELD ) | + (1 <<NETSEC_RX_PKT_FS_FIELD ) | + (1 <<NETSEC_RX_PKT_LS_FIELD ); + +if (idx ==PKTBUFSRX -1 ) + attr |= (1 <<NETSEC_RX_PKT_LD_FIELD ); + + de->data_buf_addr_up =upper_32_bits ((dma_addr_t )addr); + de->data_buf_addr_lw =lower_32_bits ((dma_addr_t )addr); + de->buf_len_info =PKTSIZE ; + de->attr = attr; +dmb (); +netsec_cache_flush ((uintptr_t )de,sizeof (*de)); +} + +static void netsec_set_tx_de(struct netsec_priv *priv, void *addr, intlen)
drivers/net/sni_netsec.c new file +232
-0+{ +struct netsec_de *de = &priv->txde[0 ]; +u32 attr; + + attr = (1 <<NETSEC_TX_SHIFT_OWN_FIELD ) | + (1 <<NETSEC_TX_SHIFT_PT_FIELD ) | + (NETSEC_RING_GMAC <<NETSEC_TX_SHIFT_TDRID_FIELD ) | + (1 <<NETSEC_TX_SHIFT_FS_FIELD ) | + (1 <<NETSEC_TX_LAST ) | + (1 <<NETSEC_TX_SHIFT_TRS_FIELD ) | + (1 <<NETSEC_TX_SHIFT_LD_FIELD ); + + de->data_buf_addr_up =upper_32_bits ((dma_addr_t )addr); + de->data_buf_addr_lw =lower_32_bits ((dma_addr_t )addr); + de->buf_len_info = len; + de->attr = attr; +dmb (); +netsec_cache_flush ((uintptr_t )de,sizeof (*de)); +} + +static int netsec_get_phy_reg (struct netsec_priv *priv, +int phy_addr,int reg_addr) +{ +u32 data; +int ret; + +if (phy_addr !=7 ) +return -EINVAL ; + +if (netsec_set_mac_reg (priv,GMAC_REG_GAR ,NETSEC_GMAC_GAR_REG_GB | + phy_addr <<NETSEC_GMAC_GAR_REG_SHIFT_PA | + reg_addr <<NETSEC_GMAC_GAR_REG_SHIFT_GR | + (netsec_clk_type (priv->freq) << +GMAC_REG_SHIFT_CR_GAR ))) +return -ETIMEDOUT ; + + ret =netsec_mac_wait_while_busy (priv,GMAC_REG_GAR , +NETSEC_GMAC_GAR_REG_GB ); +if (ret) +return ret; + + ret =netsec_get_mac_reg (priv,GMAC_REG_GDR , &data); +if (ret) +return ret; + +return data; +} + +static int netsec_set_phy_reg (struct netsec_priv *priv, +int phy_addr,int reg_addr,u16 val) +{ +int ret; + +if (phy_addr !=7 ) +return -EINVAL ; +if (netsec_set_mac_reg (priv,GMAC_REG_GDR , val)) +return -ETIMEDOUT ; + +if (netsec_set_mac_reg (priv,GMAC_REG_GAR , + phy_addr <<NETSEC_GMAC_GAR_REG_SHIFT_PA | + reg_addr <<NETSEC_GMAC_GAR_REG_SHIFT_GR | +NETSEC_GMAC_GAR_REG_GW |NETSEC_GMAC_GAR_REG_GB | + (netsec_clk_type (priv->freq) << +GMAC_REG_SHIFT_CR_GAR ))) +return -ETIMEDOUT ; + + ret =netsec_mac_wait_while_busy (priv,GMAC_REG_GAR , +NETSEC_GMAC_GAR_REG_GB ); + +/* Developerbox implements RTL8211E PHY and there is +* a compatibility problem with F_GMAC4. +* RTL8211E expects MDC clock must be kept toggling for several +* clock cycle with MDIO high before entering the IDLE state. +* To meet this requirement, netsec driver needs to issue dummy +* read(e.g. read PHYID1(offset 0x2) register) right after write. +*/ +netsec_get_phy_reg (priv, phy_addr,MII_PHYSID1 ); + +return ret; +} + +static int netsec_mac_update_to_phy_state (struct netsec_priv *priv) +{ +struct phy_device *phydev = priv->phydev; +u32 value =0 ; + + value = phydev->duplex ?NETSEC_GMAC_MCR_REG_FULL_DUPLEX_COMMON : +NETSEC_GMAC_MCR_REG_HALF_DUPLEX_COMMON ; + +if (phydev->speed !=SPEED_1000 ) + value |=NETSEC_MCR_PS ; + +if (phydev->interface !=PHY_INTERFACE_MODE_GMII && + phydev->speed ==SPEED_100 ) + value |=NETSEC_GMAC_MCR_REG_FES ; + + value |=NETSEC_GMAC_MCR_REG_CST |NETSEC_GMAC_MCR_REG_JE ; + +if (phy_interface_is_rgmii (phydev)) + value |=NETSEC_GMAC_MCR_REG_IBN ; + +if (netsec_set_mac_reg (priv,GMAC_REG_MCR , value)) +return -ETIMEDOUT ; + +return 0 ; +} + +static int netsec_start_gmac (struct netsec_priv *priv) +{ +u32 value =0 ; +int ret; + +if (priv->max_speed !=SPEED_1000 ) + value = (NETSEC_GMAC_MCR_REG_CST | +NETSEC_GMAC_MCR_REG_HALF_DUPLEX_COMMON ); + +if (netsec_set_mac_reg (priv,GMAC_REG_MCR , value)) +return -ETIMEDOUT ; + +if (netsec_set_mac_reg (priv,GMAC_REG_BMR , +NETSEC_GMAC_BMR_REG_RESET )) +return -ETIMEDOUT ; + +/* Wait soft reset */ +mdelay (5 ); + + ret =netsec_get_mac_reg (priv,GMAC_REG_BMR , &value); +if (ret) +return ret; + +if (value &NETSEC_GMAC_BMR_REG_SWR ) +return -EAGAIN ; + +netsec_write_reg (priv,MAC_REG_DESC_SOFT_RST ,1 ); +if (netsec_wait_while_busy (priv,MAC_REG_DESC_SOFT_RST ,1 )) +return -ETIMEDOUT ; + +netsec_write_reg (priv,MAC_REG_DESC_INIT ,1 ); +if (netsec_wait_while_busy (priv,MAC_REG_DESC_INIT ,1 )) +return -ETIMEDOUT ; + +if (netsec_set_mac_reg (priv,GMAC_REG_BMR , +NETSEC_GMAC_BMR_REG_COMMON )) +return -ETIMEDOUT ; + +if (netsec_set_mac_reg (priv,GMAC_REG_RDLAR , +NETSEC_GMAC_RDLAR_REG_COMMON )) +return -ETIMEDOUT ; + +if (netsec_set_mac_reg (priv,GMAC_REG_TDLAR , +NETSEC_GMAC_TDLAR_REG_COMMON )) +return -ETIMEDOUT ; + +if (netsec_set_mac_reg (priv,GMAC_REG_MFFR ,0x80000001 )) +return -ETIMEDOUT ; + + ret =netsec_mac_update_to_phy_state (priv); +if (ret) +return ret; + + ret =netsec_get_mac_reg (priv,GMAC_REG_OMR , &value); +if (ret) +return ret; + + value |=NETSEC_GMAC_OMR_REG_SR ; + value |=NETSEC_GMAC_OMR_REG_ST ; + +netsec_write_reg (priv,NETSEC_REG_NRM_RX_INTEN_CLR , ~0 ); +netsec_write_reg (priv,NETSEC_REG_NRM_TX_INTEN_CLR , ~0 ); + +if (netsec_set_mac_reg (priv,GMAC_REG_OMR , value)) +return -ETIMEDOUT ; + +return 0 ; +} + +static int netsec_stop_gmac (struct netsec_priv *priv) +{ +u32 value; +int ret; + + ret =netsec_get_mac_reg (priv,GMAC_REG_OMR , &value); +if (ret) +return ret; + value &= ~NETSEC_GMAC_OMR_REG_SR ; + value &= ~NETSEC_GMAC_OMR_REG_ST ; + +/* disable all interrupts */ +netsec_write_reg (priv,NETSEC_REG_NRM_RX_INTEN_CLR , ~0 ); +netsec_write_reg (priv,NETSEC_REG_NRM_TX_INTEN_CLR , ~0 ); + +return netsec_set_mac_reg (priv,GMAC_REG_OMR , value); +} + +static void netsec_spi_read (char *buf,loff_t len,loff_t offset) +{ +struct udevice *new; +struct spi_flash *flash; + +spi_flash_probe_bus_cs (CONFIG_SF_DEFAULT_BUS ,CONFIG_SF_DEFAULT_CS , +CONFIG_SF_DEFAULT_SPEED ,CONFIG_SF_DEFAULT_MODE , &new); + flash =dev_get_uclass_priv (new); + +spi_flash_read (flash, offset, len, buf); +} + +static int netsec_read_rom_hwaddr (struct udevice *dev) +{ +struct netsec_priv *priv =dev_get_priv (dev); +struct eth_pdata *pdata =dev_get_plat (dev); +char macp[NOR_BLOCK ]; + +netsec_spi_read (macp,sizeof (macp), priv->eeprom_base); + + pdata->enetaddr[0 ] =readb (macp +3 ); + pdata->enetaddr[1 ] =readb (macp +2 ); + pdata->enetaddr[2 ] =readb (macp +1 ); + pdata->enetaddr[3 ] =readb (macp +0 ); + pdata->enetaddr[4 ] =readb (macp +7 ); + pdata->enetaddr[5 ] =readb (macp +6 ); +return 0 ; +} + +static int netsec_send (struct udevice *dev,void *packet,int length) +{ +struct netsec_priv *priv =dev_get_priv (dev); +u32 val, tout; + + val =netsec_read_reg (priv,NETSEC_REG_NRM_TX_STATUS ); +netsec_cache_flush ((uintptr_t )packet, length); +netsec_set_tx_de (priv, packet, length); +netsec_write_reg (priv,NETSEC_REG_NRM_TX_PKTCNT ,1 );/* submit another tx */
drivers/net/sni_netsec.c new file +19
-0+ + val =netsec_read_reg (priv,NETSEC_REG_NRM_TX_PKTCNT ); + + tout =10000 ; +do { + val =netsec_read_reg (priv,NETSEC_REG_NRM_TX_DONE_PKTCNT ); +udelay (2 ); + }while (--tout && !val); + +if (!tout) { + val =netsec_read_reg (priv,NETSEC_REG_NRM_TX_PKTCNT ); +pr_err ("%s: ETIMEDOUT: %dpackets\n" , __func__, val); +return -ETIMEDOUT ; + } + +return 0 ; +} + +static int netsec_free_packet(struct udevice *dev, uchar *packet, intlength)
drivers/net/sni_netsec.c new file +47
-0+{ +struct netsec_priv *priv =dev_get_priv (dev); + +netsec_set_rx_de (priv, priv->rxat, net_rx_packets[priv->rxat]); + + priv->rxat++; +if (priv->rxat ==PKTBUFSRX ) + priv->rxat =0 ; + +return 0 ; +} + +static int netsec_recv (struct udevice *dev,int flags,uchar **packetp) +{ +struct netsec_priv *priv =dev_get_priv (dev); +int idx = priv->rxat; +uchar *ptr = net_rx_packets[idx]; +struct netsec_de *de = &priv->rxde[idx]; +int length =0 ; + +netsec_cache_invalidate ((uintptr_t )de,sizeof (*de)); + +if (de->attr & (1U <<NETSEC_RX_PKT_OWN_FIELD )) +return -EAGAIN ; + + length = de->buf_len_info >>16 ; + +/* invalidate after DMA is done */ +netsec_cache_invalidate ((uintptr_t )ptr, length); + *packetp = ptr; + +return length; +} + +static int _netsec_get_phy_reg (struct mii_dev *bus, +int phy_addr,int devad,int reg_addr) +{ +return netsec_get_phy_reg (bus->priv, phy_addr, reg_addr); +} + +static int _netsec_set_phy_reg (struct mii_dev *bus, +int phy_addr,int devad,int reg_addr,u16 val) +{ +return netsec_set_phy_reg (bus->priv, phy_addr, reg_addr, val); +} + +static int netsec_mdiobus_init(struct netsec_priv *priv, const char*name)
drivers/net/sni_netsec.c new file +36
-0+{ +struct mii_dev *bus =mdio_alloc (); + +if (!bus) +return -ENOMEM ; + + bus->read = _netsec_get_phy_reg; + bus->write = _netsec_set_phy_reg; +snprintf (bus->name,sizeof (bus->name),"%s" , name); + bus->priv = priv; + +return mdio_register (bus); +} + +static int netsec_phy_init (struct netsec_priv *priv,void *dev) +{ +struct phy_device *phydev; +int ret; + + phydev =phy_connect (priv->bus, priv->phy_addr, dev, priv->phy_mode); + + phydev->supported &=PHY_GBIT_FEATURES ; +if (priv->max_speed) { + ret =phy_set_supported (phydev, priv->max_speed); +if (ret) +return ret; + } + phydev->advertising = phydev->supported; + + priv->phydev = phydev; +phy_config (phydev); + +return 0 ; +} + +static int netsec_netdev_load_ucode_region(struct netsec_priv *priv,u32 reg,
+ u32addr_h, u32addr_l, u32 size)drivers/net/sni_netsec.c new file +35
-0+{ +u64 base = ((u64 )addr_h <<32 | addr_l) -EERPROM_MAP_OFFSET ; + +while (size >0 ) { +char buf[NOR_BLOCK ]; +u32 *ucode = (u32 *)buf; +u64 off; +int i; + + off = base %NOR_BLOCK ; + base -= off; +netsec_spi_read (buf,sizeof (buf), base); + +for (i = off /4 ; i <sizeof (buf) /4 && size >0 ; i++, size--) +netsec_write_reg (priv, reg, ucode[i]); + base +=NOR_BLOCK ; + } + +return 0 ; +} + +static int netsec_netdev_load_microcode (struct netsec_priv *priv) +{ +u32 addr_h, addr_l, size; +char buf[NOR_BLOCK ]; +u32 *ucinfo = (u32 *)buf; +int err; + +netsec_spi_read (buf,sizeof (buf), priv->eeprom_base); + + addr_h = ucinfo[NETSEC_EEPROM_HM_ME_ADDRESS_H >>2 ]; + addr_l = ucinfo[NETSEC_EEPROM_HM_ME_ADDRESS_L >>2 ]; + size = ucinfo[NETSEC_EEPROM_HM_ME_SIZE >>2 ]; + + err = netsec_netdev_load_ucode_region(priv,
NETSEC_REG_DMAC_HM_CMD_BUF,
+addr_h,addr_l, size);
+ if (err)
+ return err;drivers/net/sni_netsec.c new file +6
-0+ + addr_h = ucinfo[NETSEC_EEPROM_MH_ME_ADDRESS_H >>2 ]; + addr_l = ucinfo[NETSEC_EEPROM_MH_ME_ADDRESS_L >>2 ]; + size = ucinfo[NETSEC_EEPROM_MH_ME_SIZE >>2 ]; + + err = netsec_netdev_load_ucode_region(priv,
NETSEC_REG_DMAC_MH_CMD_BUF,
+addr_h,addr_l, size);
+ if (err)
+ return err;drivers/net/sni_netsec.c new file +47
-0+ + addr_h =0 ; + addr_l = ucinfo[NETSEC_EEPROM_PKT_ME_ADDRESS >>2 ]; + size = ucinfo[NETSEC_EEPROM_PKT_ME_SIZE >>2 ]; + + err =netsec_netdev_load_ucode_region (priv,NETSEC_REG_PKT_CMD_BUF , + addr_h, addr_l, size); +if (err) +return err; + +return 0 ; +} + +void netsec_pre_init_microengine (struct netsec_priv *priv) +{ +u32 data; + +/* Remove dormant settings */ + data =netsec_get_phy_reg (priv, priv->phy_addr,MII_BMCR ); + data &= ~BMCR_PDOWN ; + data |=BMCR_ISOLATE ; +netsec_set_phy_reg (priv, priv->phy_addr,MII_BMCR , data); +mdelay (100 ); + +/* Put phy in loopback mode to guarantee RXCLK input */ + data |=BMCR_LOOPBACK ; +netsec_set_phy_reg (priv, priv->phy_addr,MII_BMCR , data); +mdelay (100 ); +} + +void netsec_post_init_microengine (struct netsec_priv *priv) +{ +u32 data; + +/* Get phy back to normal operation */ + data =netsec_get_phy_reg (priv, priv->phy_addr,MII_BMCR ); + data &= ~BMCR_LOOPBACK ; +netsec_set_phy_reg (priv, priv->phy_addr,MII_BMCR , data); +mdelay (100 ); + +/* Apply software reset */ + data |=BMCR_RESET ; +netsec_set_phy_reg (priv, priv->phy_addr,MII_BMCR , data); +mdelay (100 ); +} + +static int netsec_reset_hardware(struct netsec_priv *priv, bool
load_ucode)drivers/net/sni_netsec.c new file +37
-0+{ +u32 value; +int err; + +netsec_write_reg (priv,NETSEC_REG_CLK_EN ,0x24 ); + +/* stop DMA engines */ +if (!netsec_read_reg (priv,NETSEC_REG_ADDR_DIS_CORE )) { +netsec_write_reg (priv,NETSEC_REG_DMA_HM_CTRL , +NETSEC_DMA_CTRL_REG_STOP ); +netsec_write_reg (priv,NETSEC_REG_DMA_MH_CTRL , +NETSEC_DMA_CTRL_REG_STOP ); + + value =100 ; +while (netsec_read_reg (priv,NETSEC_REG_DMA_HM_CTRL ) & +NETSEC_DMA_CTRL_REG_STOP ) { +udelay (1000 ); +if (--value ==0 ) { +pr_err ("%s:%d timeout!\n" , __func__, __LINE__); +break ; + } + } + + value =100 ; +while (netsec_read_reg (priv,NETSEC_REG_DMA_MH_CTRL ) & +NETSEC_DMA_CTRL_REG_STOP ) { +udelay (1000 ); +if (--value ==0 ) { +pr_err ("%s:%d timeout!\n" , __func__, __LINE__); +break ; + } + } + } + +netsec_set_mac_reg (priv,GMAC_REG_BMR ,NETSEC_GMAC_BMR_REG_RESET ); + + netsec_write_reg(priv, NETSEC_REG_SOFT_RST,
NETSEC_SOFT_RST_REG_RESET);
+netsec_write_reg(priv, NETSEC_REG_SOFT_RST, NETSEC_SOFT_RST_REG_RUN);
+netsec_write_reg(priv, NETSEC_REG_COM_INIT, NETSEC_COM_INIT_REG_ALL);drivers/net/sni_netsec.c new file +59
-0+ + value =100 ; +while (netsec_read_reg (priv,NETSEC_REG_COM_INIT ) !=0 ) { +udelay (1000 ); +if (--value ==0 ) { +pr_err ("%s:%d COM_INIT timeout!\n" , __func__, __LINE__); +break ; + } + } + +/* MAC desc init */ +netsec_write_reg (priv,MAC_REG_DESC_INIT ,1 ); +netsec_wait_while_busy (priv,MAC_REG_DESC_INIT ,1 ); +/* set MAC_INTF_SEL */ +netsec_write_reg (priv,MAC_REG_INTF_SEL ,1 ); + +netsec_write_reg (priv,NETSEC_REG_CLK_EN ,1 <<5 ); + +/* set desc_start addr */ +netsec_write_reg (priv,NETSEC_REG_NRM_RX_DESC_START_UP , +upper_32_bits ((dma_addr_t )priv->rxde)); +netsec_write_reg (priv,NETSEC_REG_NRM_RX_DESC_START_LW , +lower_32_bits ((dma_addr_t )priv->rxde)); + +netsec_write_reg (priv,NETSEC_REG_NRM_TX_DESC_START_UP , +upper_32_bits ((dma_addr_t )priv->txde)); +netsec_write_reg (priv,NETSEC_REG_NRM_TX_DESC_START_LW , +lower_32_bits ((dma_addr_t )priv->txde)); + +/* set normal tx dring ring config */ +netsec_write_reg (priv,NETSEC_REG_NRM_TX_CONFIG , +1 <<NETSEC_REG_DESC_ENDIAN ); +netsec_write_reg (priv,NETSEC_REG_NRM_RX_CONFIG , +1 <<NETSEC_REG_DESC_ENDIAN ); + +if (load_ucode) { + err =netsec_netdev_load_microcode (priv); +if (err) { +pr_err ("%s: failed to load microcode (%d)\n" , + __func__, err); +return err; + } + } + +/* set desc_start addr */ +netsec_write_reg (priv,NETSEC_REG_NRM_RX_DESC_START_UP , +upper_32_bits ((dma_addr_t )priv->rxde)); +netsec_write_reg (priv,NETSEC_REG_NRM_RX_DESC_START_LW , +lower_32_bits ((dma_addr_t )priv->rxde)); + +netsec_write_reg (priv,NETSEC_REG_NRM_TX_DESC_START_UP , +upper_32_bits ((dma_addr_t )priv->txde)); +netsec_write_reg (priv,NETSEC_REG_NRM_TX_DESC_START_LW , +lower_32_bits ((dma_addr_t )priv->txde)); + +netsec_write_reg (priv,NETSEC_REG_CLK_EN ,1 <<5 ); + +/* start DMA engines */ + netsec_write_reg(priv, NETSEC_REG_DMA_TMR_CTRL, priv->freq / 1000000 -1);
drivers/net/sni_netsec.c new file +117
-0+ +netsec_pre_init_microengine (priv); + +netsec_write_reg (priv,NETSEC_REG_ADDR_DIS_CORE ,0 ); + +mdelay (100 ); + +if (!(netsec_read_reg (priv,NETSEC_REG_TOP_STATUS ) & +NETSEC_TOP_IRQ_REG_ME_START )) { +pr_err ("microengine start failed\n" ); +return -ENXIO ; + } + +netsec_post_init_microengine (priv); + +/* clear microcode load end status */ +netsec_write_reg (priv,NETSEC_REG_TOP_STATUS , +NETSEC_TOP_IRQ_REG_ME_START ); + +netsec_write_reg (priv,NETSEC_REG_CLK_EN ,1 <<5 ); + + value =netsec_read_reg (priv,NETSEC_REG_PKT_CTRL ); + value |=NETSEC_PKT_CTRL_REG_MODE_NRM ; +/* change to normal mode */ +netsec_write_reg (priv,NETSEC_REG_DMA_MH_CTRL ,MH_CTRL__MODE_TRANS ); +netsec_write_reg (priv,NETSEC_REG_PKT_CTRL , value); + + value =100 ; +while ((netsec_read_reg (priv,NETSEC_REG_MODE_TRANS_COMP_STATUS ) & +NETSEC_MODE_TRANS_COMP_IRQ_T2N ) ==0 ) { +udelay (1000 ); +if (--value ==0 ) { + value =netsec_read_reg (priv,NETSEC_REG_MODE_TRANS_COMP_STATUS ); +pr_err ("%s:%d timeout! val=%x\n" , __func__, __LINE__, value); +break ; + } + } + +/* clear any pending EMPTY/ERR irq status */ +netsec_write_reg (priv,NETSEC_REG_NRM_TX_STATUS , ~0 ); + +/* Disable TX & RX intr */ +netsec_write_reg (priv,NETSEC_REG_INTEN_CLR , ~0 ); + +return 0 ; +} + +static void netsec_stop (struct udevice *dev) +{ +struct netsec_priv *priv =dev_get_priv (dev); + +netsec_write_reg (priv,NETSEC_REG_ADDR_DIS_CORE ,7 ); +netsec_stop_gmac (priv); +phy_shutdown (priv->phydev); +netsec_reset_hardware (priv, false); +} + +static int netsec_start (struct udevice *dev) +{ +struct netsec_priv *priv =dev_get_priv (dev); +int i; + +phy_startup (priv->phydev); +netsec_start_gmac (priv); + + priv->rxat =0 ; +for (i =0 ; i <PKTBUFSRX ; i++) +netsec_set_rx_de (priv, i, net_rx_packets[i]); + +return 0 ; +} + +static int netsec_of_to_plat (struct udevice *dev) +{ +struct eth_pdata *pdata =dev_get_plat (dev); +struct netsec_priv *priv =dev_get_priv (dev); +struct ofnode_phandle_args phandle_args; +const char *phy_mode; + + pdata->iobase =dev_read_addr_index (dev,0 ); + priv->eeprom_base =dev_read_addr_index (dev,1 ) -EERPROM_MAP_OFFSET ; + + pdata->phy_interface =-1 ; + phy_mode =dev_read_prop (dev,"phy-mode" ,NULL ); +if (phy_mode) + pdata->phy_interface =phy_get_interface_by_name (phy_mode); +if (pdata->phy_interface ==-1 ) { +pr_err ("%s: Invalid PHY interface '%s'\n" , __func__, phy_mode); +return -EINVAL ; + } + +if (!dev_read_phandle_with_args (dev,"phy-handle" ,NULL ,0 ,0 , + &phandle_args)) + priv->phy_addr =ofnode_read_u32_default (phandle_args.node,"reg" ,7 ); +else + priv->phy_addr =7 ; + + pdata->max_speed =dev_read_u32_default (dev,"max-speed" ,SPEED_1000 ); + + priv->ioaddr = pdata->iobase; + priv->phy_mode = pdata->phy_interface; + priv->max_speed = pdata->max_speed; + priv->freq =250000000UL ; + +return 0 ; +} + +#define SMMU_SCR0_SHCFG_INNER (0x2 << 22) +#define SMMU_SCR0_MTCFG (0x1 << 20) +#define SMMU_SCR0_MEMATTR_INNER_OUTER_WB (0xf << 16) + +static int netsec_probe (struct udevice *dev) +{ +struct netsec_priv *priv =dev_get_priv (dev); +int ret; + + writel(SMMU_SCR0_SHCFG_INNER | SMMU_SCR0_MTCFG |
SMMU_SCR0_MEMATTR_INNER_OUTER_WB,
+ (phys_addr_t)0x52E00000);drivers/net/sni_netsec.c new file +52
-0+ +netsec_reset_hardware (priv, true); + + ret =netsec_mdiobus_init (priv, dev->name); +if (ret) { +pr_err ("Failed to initialize mdiobus: %d\n" , ret); +return ret; + } + + priv->bus =miiphy_get_dev_by_name (dev->name); + + ret =netsec_phy_init (priv, dev); +if (ret) { +pr_err ("Failed to initialize phy: %d\n" , ret); + goto out_mdiobus_release; + } + +return 0 ; +out_mdiobus_release: +mdio_unregister (priv->bus); +mdio_free (priv->bus); +return ret; +} + +static int netsec_remove (struct udevice *dev) +{ +struct netsec_priv *priv =dev_get_priv (dev); + +free (priv->phydev); +mdio_unregister (priv->bus); +mdio_free (priv->bus); + +return 0 ; +} + +static const struct eth_ops netsec_ops = { + .start = netsec_start, + .stop = netsec_stop, + .send = netsec_send, + .recv = netsec_recv, + .free_pkt = netsec_free_packet, + .read_rom_hwaddr = netsec_read_rom_hwaddr, +}; + +static const struct udevice_id netsec_ids[] = { + { + .compatible ="socionext,synquacer-netsec" , + }, + {} +}; + +U_BOOT_DRIVER (ave) = {
drivers/net/sni_netsec.c line 1134
Quoted 10 lines
drivers/net/sni_netsec.c new file +10
-0+ .name = "synquacer_netsec", + .id = UCLASS_ETH, + .of_match = netsec_ids, + .probe = netsec_probe, + .remove = netsec_remove, + .of_to_plat = netsec_of_to_plat, + .ops = &netsec_ops, + .priv_auto = sizeof(struct netsec_priv), + .plat_auto = sizeof(struct eth_pdata), +};
Applied to u-boot-net/master, thanks!
Best regards,
Ramon Fried
PATCH v5 9/13 i2c: synquacer: SNI Synquacer I2C controller
In reply to Masami HiramatsuFrom: Jassi Brar <[email protected]>
Add driver for class of I2C controllers found on
Socionext Synquacer platform.
--- drivers/i2c/Kconfig | 7 + drivers/i2c/Makefile | 1 drivers/i2c/synquacer_i2c.c | 338 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 346 insertions(+) create mode 100644 drivers/i2c/synquacer_i2c.c
drivers/i2c/Kconfig +7 -0
@@ -455,6 +455,13 @@ config SYS_I2C_STM32F7 _ Optional clock stretching _ Software reset +config SYS_I2C_SYNQUACER + bool "Socionext SynQuacer I2C controller" + depends on ARCH_SYNQUACER && DM_I2C + help + Support for Socionext Synquacer I2C controller. This I2C controller + will be used for RTC and LS-connector on DeveloperBox. + config SYS_I2C_TEGRA bool "NVIDIA Tegra internal I2C controller" depends on ARCH_TEGRA
drivers/i2c/Makefile +1 -0
@@ -43,6 +43,7 @@ obj-$(CONFIG_SYS_I2C_SANDBOX) += sandbox_i2c.o i2c-emul-uclass.o obj-$(CONFIG_SYS_I2C_SH) += sh_i2c.o obj-$(CONFIG_SYS_I2C_SOFT) += soft_i2c.o obj-$(CONFIG_SYS_I2C_STM32F7) += stm32f7_i2c.o +obj-$(CONFIG_SYS_I2C_SYNQUACER) += synquacer_i2c.o obj-$(CONFIG_SYS_I2C_TEGRA) += tegra_i2c.o obj-$(CONFIG_SYS_I2C_UNIPHIER) += i2c-uniphier.o obj-$(CONFIG_SYS_I2C_UNIPHIER_F) += i2c-uniphier-f.o
drivers/i2c/synquacer_i2c.c new file +338 -0
338 lines not on this page · raw message
PATCH v5 10/13 ARM: dts: synquacer: Add device trees for DeveloperBox
In reply to Masami HiramatsuAdd device trees for 96boards EE DeveloperBox and basement SynQuacer SoC dtsi. These files are imported from EDK2
commit 83d38b0b4c0f240d4488c600bbe87cea391f3922
as-is (except for the changes #include path and some macros).
And add U-Boot specific changes in synquacer-sc2a11-developerbox-u-boot.dtsi
---
Changes in v4:
- Add i2c0 and RTC node.
Changes in v3:
- Use generic nor flash instead of specific mx25u51245g. (chip parameters will be searched by the register value)
Changes in v2:
- Add reference commit id of original EDK2 to the comment
- Just copy the EDK2 dts files as-is (change #include path)
- Split out the u-boot specific changes in -u-boot.dtsi.
- Removed unneeded spi-nor flash partition information.
--- arch/arm/dts/Makefile | 2 arch/arm/dts/synquacer-sc2a11-caches.dtsi | 73 ++ .../dts/synquacer-sc2a11-developerbox-u-boot.dtsi | 75 +++ arch/arm/dts/synquacer-sc2a11-developerbox.dts | 56 ++ arch/arm/dts/synquacer-sc2a11.dtsi | 595 ++++++++++++++++++++ 5 files changed, 801 insertions(+) create mode 100644 arch/arm/dts/synquacer-sc2a11-caches.dtsi create mode 100644 arch/arm/dts/synquacer-sc2a11-developerbox-u-boot.dtsi create mode 100644 arch/arm/dts/synquacer-sc2a11-developerbox.dts create mode 100644 arch/arm/dts/synquacer-sc2a11.dtsi
arch/arm/dts/Makefile +2 -0
@@ -1103,6 +1103,8 @@ dtb-$(CONFIG_TARGET_PRESIDIO_ASIC) += ca-presidio-engboard.dtb dtb-$(CONFIG_TARGET_IMX8MM_CL_IOT_GATE) += imx8mm-cl-iot-gate.dtb +dtb-$(CONFIG_ARCH_SYNQUACER) += synquacer-sc2a11-developerbox.dtb + targets += $(dtb-y) # Add any required device tree compiler flags here
arch/arm/dts/synquacer-sc2a11-caches.dtsi new file +73 -0
73 lines not on this page · raw message
arch/arm/dts/synquacer-sc2a11-developerbox-u-boot.dtsi new file +75 -0
75 lines not on this page · raw message
arch/arm/dts/synquacer-sc2a11-developerbox.dts new file +56 -0
56 lines not on this page · raw message
arch/arm/dts/synquacer-sc2a11.dtsi new file +595 -0
595 lines not on this page · raw message
PATCH v5 11/13 board: synquacer: Add DeveloperBox 96boards EE support
In reply to Masami HiramatsuAdd the DeveloperBox 96boards EE support. This board is also known as Socionext SynQuacer E-Series. It contians one "SC2A11" SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots, 3 PCIe slots (1 4x port and 2 1x ports which are expanded via PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard MicroATX Form Factor.
For more information, see this page;
https://www.96boards.org/product/developerbox/
---
Changes in v5:
- Remove log level from config.
Changes in v4:
- Add I2C and RTC configuration.
- Enable RTC and Date command.
- Remove I2C0 node before booting linux to hide it same as EDK2 does.
- Add some configurations to make it EBBR compliant.
Changes in v3:
- Enable CONFIG_MMC_SDHCI_F_SDH30.
- Enable CONFIG_CMD_GENERIC (fstype command) for distro boot.
- Remove unneeded CONFIG_ONLY_GENERIC_GPIO.
Changes in v2:
- Do not include arch/gpio.h and remove arch-sc2a11/gpio.h.
- Remove non-UEFI boot commands.
- Use Distro boot.
- Remove NOR-connected SPI node by path instead of alias.
- Rename configs/SynQuacer_defconfig to configs/synquacer_developerbox_defconfig.
- Rename include/configs/SynQuacer.h to include/configs/synquacer.h.
- Move README under doc/board/socionext/ and make it .rst text.
--- arch/arm/Kconfig | 14 +++ board/socionext/developerbox/Kconfig | 36 +++++++ board/socionext/developerbox/MAINTAINERS | 14 +++ board/socionext/developerbox/Makefile | 9 ++ board/socionext/developerbox/developerbox.c | 146 +++++++++++++++++++++++++++ configs/synquacer_developerbox_defconfig | 112 +++++++++++++++++++++ doc/board/index.rst | 1 doc/board/socionext/developerbox.rst | 87 ++++++++++++++++ doc/board/socionext/index.rst | 9 ++ include/configs/synquacer.h | 109 ++++++++++++++++++++ 10 files changed, 537 insertions(+) create mode 100644 board/socionext/developerbox/Kconfig create mode 100644 board/socionext/developerbox/MAINTAINERS create mode 100644 board/socionext/developerbox/Makefile create mode 100644 board/socionext/developerbox/developerbox.c create mode 100644 configs/synquacer_developerbox_defconfig create mode 100644 doc/board/socionext/developerbox.rst create mode 100644 doc/board/socionext/index.rst create mode 100644 include/configs/synquacer.h
arch/arm/Kconfig +14 -0
@@ -1760,6 +1760,19 @@ config ARCH_UNIPHIER Support for UniPhier SoC family developed by Socionext Inc. (formerly, System LSI Business Division of Panasonic Corporation) +config ARCH_SYNQUACER + bool "Socionext SynQuacer SoCs" + select ARM64 + select DM + select GIC_V3 + select PSCI_RESET + select SYSRESET + select SYSRESET_PSCI + select OF_CONTROL + help + Support for SynQuacer SoC family developed by Socionext Inc. + This SoC is used on 96boards EE DeveloperBox. + config ARCH_STM32 bool "Support STMicroelectronics STM32 MCU with cortex M" select CPU_V7M
@@ -2102,6 +2115,7 @@ source "board/hisilicon/poplar/Kconfig" source "board/isee/igep003x/Kconfig" source "board/kontron/sl28/Kconfig" source "board/myir/mys_6ulx/Kconfig" +source "board/socionext/developerbox/Kconfig" source "board/spear/spear300/Kconfig" source "board/spear/spear310/Kconfig" source "board/spear/spear320/Kconfig"
board/socionext/developerbox/Kconfig new file +36 -0
@@ -0,0 +1,36 @@ +if ARCH_SYNQUACER + +choice + prompt "SC2A11 Cortex-A53 MPCore 24cores" + optional + +config TARGET_DEVELOPERBOX + bool "Socionext DeveloperBox" + select PCI + select DM_PCI + select PCIE_ECAM_SYNQUACER + select SYS_DISABLE_DCACHE_OPS + select OF_BOARD_SETUP + help + Choose this option if you build the U-Boot for the DeveloperBox + 96boards Enterprise Edition. + This board will booted from SCP firmware and it enables SMMU, thus + the dcache is updated automatically when DMA operation is executed. +endchoice + +config SYS_SOC + default "sc2a11" + +if TARGET_DEVELOPERBOX + +config SYS_BOARD + default "developerbox" + +config SYS_VENDOR + default "socionext" + +config SYS_CONFIG_NAME + default "synquacer" + +endif +endif
board/socionext/developerbox/MAINTAINERS new file +14 -0
@@ -0,0 +1,14 @@ +DEVELOPER BOX +M: Masami Hiramatsu <[email protected]> +M: Jassi Brar <[email protected]> +S: Maintained +F: arch/arm/dts/synquacer-* +F: board/socionext/developerbox/* +F: configs/synquacer_developerbox_defconfig +F: drivers/i2c/synquacer_i2c.c +F: drivers/mmc/f_sdh30.c +F: drivers/net/sni_netsec.c +F: drivers/pci/pcie_ecam_synquacer.c +F: drivers/spi/spi-synquacer.c +F: include/configs/synquacer.h +F: doc/board/socionext/developerbox.rst
board/socionext/developerbox/Makefile new file +9 -0
@@ -0,0 +1,9 @@ +# +# Author: Masami Hiramatsu <[email protected]> +# +# Copyright (C) 2021 Linaro Ltd. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := developerbox.o
board/socionext/developerbox/developerbox.c new file +146 -0
146 lines not on this page · raw message
configs/synquacer_developerbox_defconfig new file +112 -0
112 lines not on this page · raw message
doc/board/index.rst +1 -0
@@ -21,6 +21,7 @@ Board-specific doc rockchip/index sifive/index sipeed/index + socionext/index st/index tbs/index toradex/index
doc/board/socionext/developerbox.rst new file +87 -0
87 lines not on this page · raw message
doc/board/socionext/index.rst new file +9 -0
@@ -0,0 +1,9 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Socionext +========= + +.. toctree:: + :maxdepth: 2 + + developerbox
include/configs/synquacer.h new file +109 -0
109 lines not on this page · raw message
PATCH v5 12/13 doc: qemu: arm64: Fix the documentation of capsule update
In reply to Masami HiramatsuSince the EDK2 GenerateCapsule script is out of date and it doesn't generate the supported version capsule file, the document should refer the mkeficapsule in tools.
--- doc/board/emulation/qemu_capsule_update.rst | 11 ++--------- 1 file changed, 2 insertions(+), 9 deletions(-)
doc/board/emulation/qemu_capsule_update.rst +2 -9
@@ -39,16 +39,9 @@ In addition, the following config needs to be disabled(QEMU ARM specific):: CONFIG_TFABOOT -The capsule file can be generated by using the GenerateCapsule.py -script in EDKII:: - - $ ./BaseTools/BinWrappers/PosixLike/GenerateCapsule -e -o \ - <capsule_file_name> --fw-version <val> --lsv <val> --guid \ - e2bb9c06-70e9-4b14-97a3-5a7913176e3f --verbose --update-image-index \ - <val> --verbose <u-boot.bin> +The capsule file can be generated by using the tools/mkeficapsule:: -The above is a wrapper script(GenerateCapsule) which eventually calls -the actual GenerateCapsule.py script. + $ mkeficapsule --raw <u-boot.bin> --index 1 <capsule_file_name> As per the UEFI specification, the capsule file needs to be placed on the EFI System Partition, under the \EFI\UpdateCapsule directory. The
PATCH v5 13/13 configs: synquacer: Enable EFI capsule update support
In reply to Masami HiramatsuEnable EFI capsule update support. With the EFI capsule update, you can update U-Boot, TF-A and OP-TEE. TF-A and OP-TEE are usually combined as a FIP binary, but if the binary is bigger than 480KB, you have to modify FIP header, split the OP-TEE and stores the OP-TEE binary in the different place. This configuration supports both cases.
---
Changes in v4:
- Add some config options for EBBR.
Changes in v3:
- Fix a typo in dfu_alt_info.
--- configs/synquacer_developerbox_defconfig | 17 +++++++++++++++++ include/configs/synquacer.h | 6 ++++++ 2 files changed, 23 insertions(+)
configs/synquacer_developerbox_defconfig +17 -0
@@ -110,3 +110,20 @@ CONFIG_DM_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_PCI=y CONFIG_USB_STORAGE=y +CONFIG_EFI_RUNTIME_UPDATE_CAPSULE=y +CONFIG_EFI_CAPSULE_ON_DISK=y +CONFIG_EFI_CAPSULE_FIRMWARE_MANAGEMENT=y +CONFIG_EFI_CAPSULE_FIRMWARE=y +CONFIG_EFI_CAPSULE_FIRMWARE_RAW=y +CONFIG_EFI_CAPSULE_FIRMWARE_FIT=y +CONFIG_EFI_CAPSULE_FMP_HEADER=y +CONFIG_FLASH_CFI_MTD=y +CONFIG_CMD_DFU=y +CONFIG_DFU_TFTP=y +CONFIG_DFU_MTD=y +CONFIG_DFU_RAM=y +CONFIG_DFU_SF=y +CONFIG_DFU_SF_PART=y +CONFIG_FIT=y +CONFIG_OF_LIBFDT=y +CONFIG_CMD_ERASEENV=y
include/configs/synquacer.h +6 -0
@@ -61,6 +61,11 @@/* Since U-Boot 64bit PCIe support is limited, disable 64bit MMIO support */ /* #define CONFIG_SYS_PCI_64BIT 1 */ +#define DEFAULT_DFU_ALT_INFO "dfu_alt_info=" \ + "mtd nor1=u-boot.bin raw 200000 100000;" \ + "fip.bin raw 180000 78000;" \ + "optee.bin raw 500000 100000\0" +/* Distro boot settings */ #ifndef CONFIG_SPL_BUILD #ifdef CONFIG_CMD_USB
@@ -104,6 +109,7 @@"ramdisk_addr_r=0xa0000000\0" \"scriptaddr=0x88000000\0" \"pxefile_addr_r=0x88100000\0" \ +DEFAULT_DFU_ALT_INFO \ BOOTENV#endif /* __CONFIG_H */
Hello,
Would anyone have any comments on this series?
Thank you,
2021年6月4日(金) 18:43 Masami Hiramatsu <[email protected]>:
Quoted 141 lines
Hi,
Here is the 5th version of the series (including some fixes for build errors) to add SynQuacer/DeveloperBox 96board EE suport on U-Boot.
This series includes not only DeveloperBox support but also some fixes for the issues which I faced while porting U-Boot on the DeveloperBox. First 3 patches are fixes, next 1 patch is a code cleanup for generic gpio for arm. The next 7 patches adding DeveloperBox devices and board support. The last 2 patches are related to the UEFI capsule update.
Previous version is here:
https://lists.denx.de/pipermail/u-boot/2021-May/449305.html
Changes in v5
-------------I dripped
dfu_mtdbugfix patch (previous [12/14]) from this, because Sughosh already fixed it.[11/13]:
- Remove log level from config.DeveloperBox
============DeveloperBox is a certified 96boards Enterprise Edition board. The board/SoC has: -
* Socionext SC2A11 24-cores ARM Cortex-A53 on tbe Mini-ATX form factor motherboard
* 4 DIMM slots (4GB DDR4-2400 UDIMM shipped by default)
* 1 4xPCIe Gen2 slot and 2 1xPCIe Gen2 slots
(1x slots are connected via PCIe bridge chip)
* 4 USB-3.0 ports
* 2 SATA ports
* 1 GbE network port
* 1 USB-UART serial port (micro USB)
* 64MB SPI NOR Flash
* 8GB eMMC Flash Storage
* 96boards LS connectorThe DeveloperBox schematic can be found here: -
https://www.96boards.org/documentation/enterprise/developerbox/hardware-docs/mzsc2am_v03_20180115_a.pdfAnd the other documents can be found here: -
https://www.96boards.org/documentation/enterprise/developerbox/Currently, the U-Boot port supports: -
* USB
* eMMC
* SPI-NOR
* SATA
* GbEThe DeveloperBox boots the TF-A and EDK2 as a main bootloader by default. The DeveloperBox U-Boot port will replace the EDK2 and boot from TF-A as BL33, but no need to combine with it.
Thank you,
---
Jassi Brar (4):
mmc: synquacer: Add SynQuacerF_SDH30SDHCI driver
spi: synquacer: Add HSSPI SPI controller driver for SynQuacer
net: synquacer: Add netsec driver
i2c: synquacer: SNI Synquacer I2C controllerMasami Hiramatsu (9):
ata: ahci-pci: Usescsi_opsto initialize ops
dm: pci: Skip setting VGA bridge bits if parent device is the host bus
efi: Fix to use null handle to create new handle forefi_fmp_raw
gpio: IntroduceCONFIG_GPIO_EXTRA_HEADERto cleanup #ifdefs
pci: synquacer: Add SynQuacer ECAM based PCIe driver
ARM: dts: synquacer: Add device trees for DeveloperBox
board: synquacer: Add DeveloperBox 96boards EE support
doc: qemu: arm64: Fix the documentation of capsule update
configs: synquacer: Enable EFI capsule update supportarch/arm/Kconfig | 108 ++ arch/arm/dts/Makefile | 2 arch/arm/dts/synquacer-sc2a11-caches.dtsi | 73 + .../dts/synquacer-sc2a11-developerbox-u-boot.dtsi | 75 + arch/arm/dts/synquacer-sc2a11-developerbox.dts | 56 + arch/arm/dts/synquacer-sc2a11.dtsi | 595 ++++++++++ arch/arm/include/asm/gpio.h | 8 board/socionext/developerbox/Kconfig | 36 + board/socionext/developerbox/MAINTAINERS | 14 board/socionext/developerbox/Makefile | 9 board/socionext/developerbox/developerbox.c | 146 +++ configs/synquacer_developerbox_defconfig | 129 ++ doc/board/emulation/qemu_capsule_update.rst | 11 doc/board/index.rst | 1 doc/board/socionext/developerbox.rst | 87 ++ doc/board/socionext/index.rst | 9 drivers/ata/ahci-pci.c | 2 drivers/i2c/Kconfig | 7 drivers/i2c/Makefile | 1 drivers/i2c/synquacer_i2c.c | 338 ++++++ drivers/mmc/Kconfig | 10 drivers/mmc/Makefile | 1 drivers/mmc/f_sdh30.c | 81 + drivers/net/Kconfig | 8 drivers/net/Makefile | 1 drivers/net/sni_netsec.c | 1134 ++++++++++++++++++++ drivers/pci/Kconfig | 12 drivers/pci/Makefile | 1 drivers/pci/pci-uclass.c | 3 drivers/pci/pcie_ecam_synquacer.c | 600 +++++++++++ drivers/spi/Kconfig | 8 drivers/spi/Makefile | 1 drivers/spi/spi-synquacer.c | 491 +++++++++ include/configs/synquacer.h | 115 ++ lib/efi_loader/efi_capsule.c | 2 35 files changed, 4158 insertions(+), 17 deletions(-) create mode 100644 arch/arm/dts/synquacer-sc2a11-caches.dtsi create mode 100644 arch/arm/dts/synquacer-sc2a11-developerbox-u-boot.dtsi create mode 100644 arch/arm/dts/synquacer-sc2a11-developerbox.dts create mode 100644 arch/arm/dts/synquacer-sc2a11.dtsi create mode 100644 board/socionext/developerbox/Kconfig create mode 100644 board/socionext/developerbox/MAINTAINERS create mode 100644 board/socionext/developerbox/Makefile create mode 100644 board/socionext/developerbox/developerbox.c create mode 100644 configs/synquacer_developerbox_defconfig create mode 100644 doc/board/socionext/developerbox.rst create mode 100644 doc/board/socionext/index.rst create mode 100644 drivers/i2c/synquacer_i2c.c create mode 100644 drivers/mmc/f_sdh30.c create mode 100644 drivers/net/sni_netsec.c create mode 100644 drivers/pci/pcie_ecam_synquacer.c create mode 100644 drivers/spi/spi-synquacer.c create mode 100644 include/configs/synquacer.h--
Masami Hiramatsu <[email protected]>
Signature · 1 line
Masami Hiramatsu
Quoted 160 lines · Masami Hiramatsu
Hello,
Would anyone have any comments on this series?
Thank you,
2021年6月4日(金) 18:43 Masami Hiramatsu <[email protected]>:
Quoted 24 lines
Hi,
Here is the 5th version of the series (including some fixes for build errors) to add SynQuacer/DeveloperBox 96board EE suport on U-Boot.
This series includes not only DeveloperBox support but also some fixes for the issues which I faced while porting U-Boot on the DeveloperBox. First 3 patches are fixes, next 1 patch is a code cleanup for generic gpio for arm. The next 7 patches adding DeveloperBox devices and board support. The last 2 patches are related to the UEFI capsule update.
Previous version is here:
https://lists.denx.de/pipermail/u-boot/2021-May/449305.html
Changes in v5
-------------I dripped
dfu_mtdbugfix patch (previous [12/14]) from this, because Sughosh already fixed it.Quoted 8 lines
[11/13]:
- Remove log level from config.DeveloperBox
============DeveloperBox is a certified 96boards Enterprise Edition board. The
board/SoC has: -
Quoted 1 line
* Socionext SC2A11 24-cores ARM Cortex-A53 on tbe Mini-ATX form factor
motherboard
Quoted 11 lines
* 4 DIMM slots (4GB DDR4-2400 UDIMM shipped by default)
* 1 4xPCIe Gen2 slot and 2 1xPCIe Gen2 slots (1x slots are connected via PCIe bridge chip)
* 4 USB-3.0 ports
* 2 SATA ports
* 1 GbE network port
* 1 USB-UART serial port (micro USB)
* 64MB SPI NOR Flash
* 8GB eMMC Flash Storage
* 96boards LS connectorQuoted 2 lines
The DeveloperBox schematic can be found here: -
Quoted 27 lines
And the other documents can be found here: -
https://www.96boards.org/documentation/enterprise/developerbox/Currently, the U-Boot port supports: -
* USB
* eMMC
* SPI-NOR
* SATA
* GbEThe DeveloperBox boots the TF-A and EDK2 as a main bootloader by default. The DeveloperBox U-Boot port will replace the EDK2 and boot from TF-A as BL33, but no need to combine with it.
Thank you,
---
Jassi Brar (4):
mmc: synquacer: Add SynQuacerF_SDH30SDHCI driver
spi: synquacer: Add HSSPI SPI controller driver for SynQuacer
net: synquacer: Add netsec driver
i2c: synquacer: SNI Synquacer I2C controllerQuoted 3 lines
Masami Hiramatsu (9):
ata: ahci-pci: Usescsi_opsto initialize ops
dm: pci: Skip setting VGA bridge bits if parent device is the hostbus
Quoted 27 lines
efi: Fix to use null handle to create new handle for
efi_fmp_raw
gpio: IntroduceCONFIG_GPIO_EXTRA_HEADERto cleanup #ifdefs
pci: synquacer: Add SynQuacer ECAM based PCIe driver
ARM: dts: synquacer: Add device trees for DeveloperBox
board: synquacer: Add DeveloperBox 96boards EE support
doc: qemu: arm64: Fix the documentation of capsule update
configs: synquacer: Enable EFI capsule update supportarch/arm/Kconfig | 108 ++ arch/arm/dts/Makefile | 2 arch/arm/dts/synquacer-sc2a11-caches.dtsi | 73 + .../dts/synquacer-sc2a11-developerbox-u-boot.dtsi | 75 + arch/arm/dts/synquacer-sc2a11-developerbox.dts | 56 + arch/arm/dts/synquacer-sc2a11.dtsi | 595 ++++++++++ arch/arm/include/asm/gpio.h | 8 board/socionext/developerbox/Kconfig | 36 + board/socionext/developerbox/MAINTAINERS | 14 board/socionext/developerbox/Makefile | 9 board/socionext/developerbox/developerbox.c | 146 +++ configs/synquacer_developerbox_defconfig | 129 ++ doc/board/emulation/qemu_capsule_update.rst | 11 doc/board/index.rst | 1 doc/board/socionext/developerbox.rst | 87 ++ doc/board/socionext/index.rst | 9 drivers/ata/ahci-pci.c | 2 drivers/i2c/Kconfig | 7Quoted 8 lines
drivers/i2c/Makefile | 1 drivers/i2c/synquacer_i2c.c | 338 ++++++ drivers/mmc/Kconfig | 10 drivers/mmc/Makefile | 1 drivers/mmc/f_sdh30.c | 81 + drivers/net/Kconfig | 8 drivers/net/Makefile | 1 drivers/net/sni_netsec.c | 1134++++++++++++++++++++
Quoted 4 lines
drivers/pci/Kconfig | 12 drivers/pci/Makefile | 1 drivers/pci/pci-uclass.c | 3 drivers/pci/pcie_ecam_synquacer.c | 600 +++++++++++Quoted 8 lines
drivers/spi/Kconfig | 8 drivers/spi/Makefile | 1 drivers/spi/spi-synquacer.c | 491 +++++++++ include/configs/synquacer.h | 115 ++ lib/efi_loader/efi_capsule.c | 2 35 files changed, 4158 insertions(+), 17 deletions(-) create mode 100644 arch/arm/dts/synquacer-sc2a11-caches.dtsi create mode 100644
arch/arm/dts/synquacer-sc2a11-developerbox-u-boot.dtsiQuoted 16 lines
create mode 100644 arch/arm/dts/synquacer-sc2a11-developerbox.dts create mode 100644 arch/arm/dts/synquacer-sc2a11.dtsi create mode 100644 board/socionext/developerbox/Kconfig create mode 100644 board/socionext/developerbox/MAINTAINERS create mode 100644 board/socionext/developerbox/Makefile create mode 100644 board/socionext/developerbox/developerbox.c create mode 100644 configs/synquacer_developerbox_defconfig create mode 100644 doc/board/socionext/developerbox.rst create mode 100644 doc/board/socionext/index.rst create mode 100644 drivers/i2c/synquacer_i2c.c create mode 100644 drivers/mmc/f_sdh30.c create mode 100644 drivers/net/sni_netsec.c create mode 100644 drivers/pci/pcie_ecam_synquacer.c create mode 100644 drivers/spi/spi-synquacer.c create mode 100644 include/configs/synquacer.hQuoted 2 lines
--
Masami Hiramatsu <[email protected]>--
Masami Hiramatsu