icmp: don't send out ICMP messages with a source address of 0.0.0.0
Subsystems (4)
PATCH v2 1/2 icmp: don't send out ICMP messages with a source address of 0.0.0.0
When constructing ICMP response messages, the kernel will try to pick a suitable source address for the outgoing packet. However, if no IPv4 addresses are configured on the system at all, this will fail and we end up producing an ICMP message with a source address of 0.0.0.0. This can happen on a box routing IPv4 traffic via v6 nexthops, for instance.
Since 0.0.0.0 is not generally routable on the internet, there's a good chance that such ICMP messages will never make it back to the sender of the original packet that the ICMP message was sent in response to. This, in turn, can create connectivity and PMTUd problems for senders. Fortunately, RFC7600 reserves a dummy address to be used as a source for ICMP messages (192.0.0.8/32), so let's teach the kernel to substitute that address as a last resort if the regular source address selection procedure fails.
Below is a quick example reproducing this issue with network namespaces:
ip netns add ns0
ip l add type veth peer netns ns0
ip l set dev veth0 up
ip a add 10.0.0.1/24 dev veth0
ip a add fc00:dead:cafe:42::1/64 dev veth0
ip r add 10.1.0.0/24 via inet6 fc00:dead:cafe:42::2
ip -n ns0 l set dev veth0 up
ip -n ns0 a add fc00:dead:cafe:42::2/64 dev veth0
ip -n ns0 r add 10.0.0.0/24 via inet6 fc00:dead:cafe:42::1
ip netns exec ns0 sysctl -w net.ipv4.icmp_ratelimit=0
ip netns exec ns0 sysctl -w net.ipv4.ip_forward=1
tcpdump -tpni veth0 -c 2 icmp &
ping -w 1 10.1.0.1 > /dev/null
tcpdump: verbose output suppressed, use -v[v]... for full protocol decode listening on veth0, link-type EN10MB (Ethernet), snapshot length 262144 bytes IP 10.0.0.1 > 10.1.0.1: ICMP echo request, id 29, seq 1, length 64 IP 0.0.0.0 > 10.0.0.1: ICMP net 10.1.0.1 unreachable, length 92
2 packets captured
2 packets received by filter
0 packets dropped by kernel
With this patch the above capture changes to:
IP 10.0.0.1 > 10.1.0.1: ICMP echo request, id 31127, seq 1, length 64 IP 192.0.0.8 > 10.0.0.1: ICMP net 10.1.0.1 unreachable, length 92
--- include/uapi/linux/in.h | 3 +++ net/ipv4/icmp.c | 7 +++++++ 2 files changed, 10 insertions(+)
include/uapi/linux/in.h +3 -0
@@ -289,6 +289,9 @@ struct sockaddr_in {/* Address indicating an error return. */ #define INADDR_NONE ((unsigned long int) 0xffffffff) +/* Dummy address for src of ICMP replies if no real address is set (RFC7600). */ +#define INADDR_DUMMY ((unsigned long int) 0xc0000008) +/* Network number for local host loopback. */ #define IN_LOOPBACKNET 127
net/ipv4/icmp.c +7 -0
@@ -759,6 +759,13 @@ void __icmp_send(struct sk_buff *skb_in, int type, int code, __be32 info, icmp_param.data_len = room; icmp_param.head_len =sizeof (struct icmphdr ); +/* if we don't have a source address at this point, fall back to the +* dummy address instead of sending out a packet with a source address +* of 0.0.0.0 +*/ +if (!fl4.saddr) + fl4.saddr =htonl (INADDR_DUMMY ); +icmp_push_reply (&icmp_param, &fl4, &ipc, &rt); ende:ip_rt_put (rt);
Signature · 1 line
2.32.0
PATCH v2 2/2 selftests/net: Add icmp.sh for testing ICMP dummy address responses
This adds a new icmp.sh selftest for testing that the kernel will respond correctly with an ICMP unreachable message with the dummy (192.0.0.8) source address when there are no IPv4 addresses configured to use as source addresses.
--- tools/testing/selftests/net/icmp.sh | 74 +++++++++++++++++++++++++++++ 1 file changed, 74 insertions(+) create mode 100755 tools/testing/selftests/net/icmp.sh
tools/testing/selftests/net/icmp.sh new file +74 -0
@@ -0,0 +1,74 @@ +#!/bin/bash +# SPDX-License-Identifier: GPL-2.0 + +# Test for checking ICMP response with dummy address instead of 0.0.0.0. +# Sets up two namespaces like: +# +----------------------+ +--------------------+ +# | ns1 | v4-via-v6 routes: | ns2 | +# | | ' | | +# | +--------+ -> 172.16.1.0/24 -> +--------+ | +# | | veth0 +--------------------------+ veth0 | | +# | +--------+ <- 172.16.0.0/24 <- +--------+ | +# | 172.16.0.1 | | 2001:db8:1::2/64 | +# | 2001:db8:1::2/64 | | | +# +----------------------+ +--------------------+ +# +# And then tries to ping 172.16.1.1 from ns1. This results in a "net +# unreachable" message being sent from ns2, but there is no IPv4 address set in +# that address space, so the kernel should substitute the dummy address +# 192.0.0.8 defined in RFC7600. + +NS1=ns1 +NS2=ns2 +H1_IP=172.16.0.1/32 +H1_IP6=2001:db8:1::1 +RT1=172.16.1.0/24 +PINGADDR=172.16.1.1 +RT2=172.16.0.0/24 +H2_IP6=2001:db8:1::2 + +TMPFILE=$(mktemp) + +cleanup() +{ + rm -f "$TMPFILE" + ip netns del $NS1 + ip netns del $NS2 +} + +trap cleanup EXIT + +# Namespaces +ip netns add $NS1 +ip netns add $NS2 + +# Connectivity +ip -netns $NS1 link add veth0 type veth peer name veth0 netns $NS2 +ip -netns $NS1 link set dev veth0 up +ip -netns $NS2 link set dev veth0 up +ip -netns $NS1 addr add $H1_IP dev veth0 +ip -netns $NS1 addr add $H1_IP6/64 dev veth0 nodad +ip -netns $NS2 addr add $H2_IP6/64 dev veth0 nodad +ip -netns $NS1 route add $RT1 via inet6 $H2_IP6 +ip -netns $NS2 route add $RT2 via inet6 $H1_IP6 + +# Make sure ns2 will respond with ICMP unreachable +ip netns exec $NS2 sysctl -qw net.ipv4.icmp_ratelimit=0 net.ipv4.ip_forward=1 + +# Run the test - a ping runs in the background, and we capture ICMP responses +# with tcpdump; -c 1 means it should exit on the first ping, but add a timeout +# in case something goes wrong +ip netns exec $NS1 ping -w 3 -i 0.5 $PINGADDR >/dev/null & +ip netns exec $NS1 timeout 10 tcpdump -tpni veth0 -c 1 'icmp and icmp[icmptype] != icmp-echo' > $TMPFILE 2>/dev/null + +# Parse response and check for dummy address +# tcpdump output looks like: +# IP 192.0.0.8 > 172.16.0.1: ICMP net 172.16.1.1 unreachable, length 92 +RESP_IP=$(awk '{print $2}' < $TMPFILE) +if [[ "$RESP_IP" != "192.0.0.8" ]]; then + echo "FAIL - got ICMP response from $RESP_IP, should be 192.0.0.8" + exit 1 +else + echo "OK" + exit 0 +fi
Signature · 1 line
2.32.0
Re: [PATCH net v2 2/2] selftests/net: Add icmp.sh for testing ICMP dummy address responses
Quoted 11 lines · Toke Høiland-Jørgensen
This adds a new
icmp.shselftest for testing that the kernel will respond correctly with an ICMP unreachable message with the dummy (192.0.0.8) source address when there are no IPv4 addresses configured to use as source addresses.Signed-off-by Toke Høiland-Jørgensen <[email protected]>--- tools/testing/selftests/net/icmp.sh | 74 +++++++++++++++++++++++++++++ 1 file changed, 74 insertions(+) create mode 100755 tools/testing/selftests/net/icmp.sh
Thanks, Toke.
This series was applied to netdev/net.git (refs/heads/master):
Hello:
This series was applied to netdev/net.git (refs/heads/master):
Quoted 15 lines · On Fri, 18 Jun 2021 13:04:35 +0200 you wrote:
When constructing ICMP response messages, the kernel will try to pick a suitable source address for the outgoing packet. However, if no IPv4 addresses are configured on the system at all, this will fail and we end up producing an ICMP message with a source address of 0.0.0.0. This can happen on a box routing IPv4 traffic via v6 nexthops, for instance.
Since 0.0.0.0 is not generally routable on the internet, there's a good chance that such ICMP messages will never make it back to the sender of the original packet that the ICMP message was sent in response to. This, in turn, can create connectivity and PMTUd problems for senders. Fortunately, RFC7600 reserves a dummy address to be used as a source for ICMP messages (192.0.0.8/32), so let's teach the kernel to substitute that address as a last resort if the regular source address selection procedure fails.
Quoted 1 line
[...]
Here is the summary with links:
- [net,v2,1/2] icmp: don't send out ICMP messages with a source address of 0.0.0.0
https://git.kernel.org/netdev/net/c/321827477360 - [net,v2,2/2] selftests/net: Add icmp.sh for testing ICMP dummy address responses https://git.kernel.org/netdev/net/c/7e9838b7915e
You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html