FAILED: patch "[PATCH] iio: accel: bma180: Fix BMA25x bandwidth register values" failed to apply to 5.4-stable tree

PATCH [email protected] 2 participants 3 messages Jul 11, 2021 – Jul 26, 2021

Subsystems (2)

Stable branch IIO

lore

Share & tools

lore

[email protected]

author maintainer

2021-07-11 13:01 UTC #0 lore raw

The patch below does not apply to the 5.4-stable tree.
If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <[email protected]>.

thanks,

greg k-h

------------------ original commit in Linus's tree ------------------

From 8090d67421ddab0ae932abab5a60200598bf0bbb Mon Sep 17 00:00:00 2001
From: Stephan Gerhold <[email protected]>
Date: Wed, 26 May 2021 11:44:07 +0200
Subject: [PATCH] iio: accel: bma180: Fix BMA25x bandwidth register values
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

According to the BMA253 datasheet [1] and BMA250 datasheet [2] the bandwidth value for BMA25x should be set as 01xxx:

"Settings 00xxx result in a bandwidth of 7.81 Hz; [...]
It is recommended [...] to use the range from ´01000b´ to ´01111b´ only in order to be compatible with future products."

However, at the moment the drivers sets bandwidth values from 0 to 6, which is not recommended and always results into 7.81 Hz bandwidth according to the datasheet.

Fix this by introducing a bw_offset = 8 = 01000b for BMA25x, so the additional bit is always set for BMA25x.

[1]: https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bma253-ds000.pdf
[2]: https://datasheet.octopart.com/BMA250-Bosch-datasheet-15540103.pdf

Cc Peter Meerwald <[email protected]>

Fixes 2017cff24cc0 ("iio:bma180: Add BMA250 chip support")

Signed-off-by Stephan Gerhold <[email protected]>

Reviewed-by Linus Walleij <[email protected]>

Link https://lore.kernel.org/r/[email protected] open here

Cc <[email protected]>

Signed-off-by Jonathan Cameron <[email protected]>

drivers/iio/accel/bma180.c +7 -2

index 4a07e60c0e21..e7c6b3096cb7 100644
@@ -55,7 +55,7 @@ struct bma180_part_info {
 
 	u8 int_reset_reg, int_reset_mask;
 	u8 sleep_reg, sleep_mask;
-	u8 bw_reg, bw_mask;
+	u8 bw_reg, bw_mask, bw_offset;
 	u8 scale_reg, scale_mask;
 	u8 power_reg, power_mask, lowpower_val;
 	u8 int_enable_reg, int_enable_mask;

@@ -127,6 +127,7 @@ struct bma180_part_info {
 
 #define BMA250_RANGE_MASK	GENMASK(3, 0) /* Range of accel values */
 #define BMA250_BW_MASK		GENMASK(4, 0) /* Accel bandwidth */
+#define BMA250_BW_OFFSET	8
 #define BMA250_SUSPEND_MASK	BIT(7) /* chip will sleep */
 #define BMA250_LOWPOWER_MASK	BIT(6)
 #define BMA250_DATA_INTEN_MASK	BIT(4)

@@ -143,6 +144,7 @@ struct bma180_part_info {
 
 #define BMA254_RANGE_MASK	GENMASK(3, 0) /* Range of accel values */
 #define BMA254_BW_MASK		GENMASK(4, 0) /* Accel bandwidth */
+#define BMA254_BW_OFFSET	8
 #define BMA254_SUSPEND_MASK	BIT(7) /* chip will sleep */
 #define BMA254_LOWPOWER_MASK	BIT(6)
 #define BMA254_DATA_INTEN_MASK	BIT(4)

@@ -287,7 +289,8 @@ static int bma180_set_bw(struct bma180_data *data, int val)
 	for (i = 0; i < data->part_info->num_bw; ++i) {
 		if (data->part_info->bw_table[i] == val) {
 			ret = bma180_set_bits(data, data->part_info->bw_reg,
-				data->part_info->bw_mask, i);
+				data->part_info->bw_mask,
+				i + data->part_info->bw_offset);
 			if (ret) {
 				dev_err(&data->client->dev,
 					"failed to set bandwidth\n");

@@ -880,6 +883,7 @@ static const struct bma180_part_info bma180_part_info[] = {
 		.sleep_mask = BMA250_SUSPEND_MASK,
 		.bw_reg = BMA250_BW_REG,
 		.bw_mask = BMA250_BW_MASK,
+		.bw_offset = BMA250_BW_OFFSET,
 		.scale_reg = BMA250_RANGE_REG,
 		.scale_mask = BMA250_RANGE_MASK,
 		.power_reg = BMA250_POWER_REG,

@@ -909,6 +913,7 @@ static const struct bma180_part_info bma180_part_info[] = {
 		.sleep_mask = BMA254_SUSPEND_MASK,
 		.bw_reg = BMA254_BW_REG,
 		.bw_mask = BMA254_BW_MASK,
+		.bw_offset = BMA254_BW_OFFSET,
 		.scale_reg = BMA254_RANGE_REG,
 		.scale_mask = BMA254_RANGE_MASK,
 		.power_reg = BMA254_POWER_REG,

Sudip Mukherjee

Reviewed-by Linus Walleij

2021-07-22 20:22 UTC #1 lore raw

Hi Greg,

Quoted 5 lines · On Sun, Jul 11, 2021 at 03:01:27PM +0200, [email protected] wrote:

The patch below does not apply to the 5.4-stable tree.
If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <[email protected]>.

Here is the backport along with 9436abc40139 ("iio: accel: bma180: Use explicit member assignment") which makes the backporting a little easier. This will apply to all branches till 4.4-stable.

--
Regards
Sudip

From 1ed1fa336683b5866b1accd67dc5bd126c9d014e Mon Sep 17 00:00:00 2001
From: Linus Walleij <[email protected]>
Date: Wed, 11 Dec 2019 22:38:18 +0100
Subject: [PATCH 1/2] iio: accel: bma180: Use explicit member assignment

commit 9436abc40139503a7cea22a96437697d048f31c0 upstream

This uses the C99 explicit .member assignment for the variant data in struct bma180_part_info. This makes it easier to understand and add new variants.

Cc Peter Meerwald <[email protected]>

Cc Oleksandr Kravchenko <[email protected]>

Signed-off-by Linus Walleij <[email protected]>

Signed-off-by Jonathan Cameron <[email protected]>

Signed-off-by Sudip Mukherjee <[email protected]>

---
 drivers/iio/accel/bma180.c | 68 ++++++++++++++++++++++++--------------
 1 file changed, 44 insertions(+), 24 deletions(-)

drivers/iio/accel/bma180.c +44 ~~-24~~

index aa301c606346..196111c91627 100644
@@ -633,32 +633,52 @@ static const struct iio_chan_spec bma250_channels[] = {
 
 static const struct bma180_part_info bma180_part_info[] = {
 	[BMA180] = {
-		bma180_channels, ARRAY_SIZE(bma180_channels),
-		bma180_scale_table, ARRAY_SIZE(bma180_scale_table),
-		bma180_bw_table, ARRAY_SIZE(bma180_bw_table),
-		BMA180_CTRL_REG0, BMA180_RESET_INT,
-		BMA180_CTRL_REG0, BMA180_SLEEP,
-		BMA180_BW_TCS, BMA180_BW,
-		BMA180_OFFSET_LSB1, BMA180_RANGE,
-		BMA180_TCO_Z, BMA180_MODE_CONFIG, BMA180_LOW_POWER,
-		BMA180_CTRL_REG3, BMA180_NEW_DATA_INT,
-		BMA180_RESET,
-		bma180_chip_config,
-		bma180_chip_disable,
+		.channels = bma180_channels,
+		.num_channels = ARRAY_SIZE(bma180_channels),
+		.scale_table = bma180_scale_table,
+		.num_scales = ARRAY_SIZE(bma180_scale_table),
+		.bw_table = bma180_bw_table,
+		.num_bw = ARRAY_SIZE(bma180_bw_table),
+		.int_reset_reg = BMA180_CTRL_REG0,
+		.int_reset_mask = BMA180_RESET_INT,
+		.sleep_reg = BMA180_CTRL_REG0,
+		.sleep_mask = BMA180_SLEEP,
+		.bw_reg = BMA180_BW_TCS,
+		.bw_mask = BMA180_BW,
+		.scale_reg = BMA180_OFFSET_LSB1,
+		.scale_mask = BMA180_RANGE,
+		.power_reg = BMA180_TCO_Z,
+		.power_mask = BMA180_MODE_CONFIG,
+		.lowpower_val = BMA180_LOW_POWER,
+		.int_enable_reg = BMA180_CTRL_REG3,
+		.int_enable_mask = BMA180_NEW_DATA_INT,
+		.softreset_reg = BMA180_RESET,
+		.chip_config = bma180_chip_config,
+		.chip_disable = bma180_chip_disable,
 	},
 	[BMA250] = {
-		bma250_channels, ARRAY_SIZE(bma250_channels),
-		bma250_scale_table, ARRAY_SIZE(bma250_scale_table),
-		bma250_bw_table, ARRAY_SIZE(bma250_bw_table),
-		BMA250_INT_RESET_REG, BMA250_INT_RESET_MASK,
-		BMA250_POWER_REG, BMA250_SUSPEND_MASK,
-		BMA250_BW_REG, BMA250_BW_MASK,
-		BMA250_RANGE_REG, BMA250_RANGE_MASK,
-		BMA250_POWER_REG, BMA250_LOWPOWER_MASK, 1,
-		BMA250_INT_ENABLE_REG, BMA250_DATA_INTEN_MASK,
-		BMA250_RESET_REG,
-		bma250_chip_config,
-		bma250_chip_disable,
+		.channels = bma250_channels,
+		.num_channels = ARRAY_SIZE(bma250_channels),
+		.scale_table = bma250_scale_table,
+		.num_scales = ARRAY_SIZE(bma250_scale_table),
+		.bw_table = bma250_bw_table,
+		.num_bw = ARRAY_SIZE(bma250_bw_table),
+		.int_reset_reg = BMA250_INT_RESET_REG,
+		.int_reset_mask = BMA250_INT_RESET_MASK,
+		.sleep_reg = BMA250_POWER_REG,
+		.sleep_mask = BMA250_SUSPEND_MASK,
+		.bw_reg = BMA250_BW_REG,
+		.bw_mask = BMA250_BW_MASK,
+		.scale_reg = BMA250_RANGE_REG,
+		.scale_mask = BMA250_RANGE_MASK,
+		.power_reg = BMA250_POWER_REG,
+		.power_mask = BMA250_LOWPOWER_MASK,
+		.lowpower_val = 1,
+		.int_enable_reg = BMA250_INT_ENABLE_REG,
+		.int_enable_mask = BMA250_DATA_INTEN_MASK,
+		.softreset_reg = BMA250_RESET_REG,
+		.chip_config = bma250_chip_config,
+		.chip_disable = bma250_chip_disable,
 	},
 };

Signature · 1 line

2.30.2

From a56bbb39c183206a3093b8d9ee09b89cc6a45589 Mon Sep 17 00:00:00 2001
From: Stephan Gerhold <[email protected]>
Date: Wed, 26 May 2021 11:44:07 +0200
Subject: [PATCH 2/2] iio: accel: bma180: Fix BMA25x bandwidth register values
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

commit 8090d67421ddab0ae932abab5a60200598bf0bbb upstream

According to the BMA253 datasheet [1] and BMA250 datasheet [2] the bandwidth value for BMA25x should be set as 01xxx:

"Settings 00xxx result in a bandwidth of 7.81 Hz; [...]
It is recommended [...] to use the range from ´01000b´ to ´01111b´ only in order to be compatible with future products."

However, at the moment the drivers sets bandwidth values from 0 to 6, which is not recommended and always results into 7.81 Hz bandwidth according to the datasheet.

Fix this by introducing a bw_offset = 8 = 01000b for BMA25x, so the additional bit is always set for BMA25x.

[1]: https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bma253-ds000.pdf
[2]: https://datasheet.octopart.com/BMA250-Bosch-datasheet-15540103.pdf

Cc Peter Meerwald <[email protected]>

Fixes 2017cff24cc0 ("iio:bma180: Add BMA250 chip support")

Signed-off-by Stephan Gerhold <[email protected]>

Reviewed-by Linus Walleij <[email protected]>

Link https://lore.kernel.org/r/[email protected] open here

Cc <[email protected]>

Signed-off-by Jonathan Cameron <[email protected]>

[sudip: adjust context]

Signed-off-by Sudip Mukherjee <[email protected]>

---
 drivers/iio/accel/bma180.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

drivers/iio/accel/bma180.c +5 -2

index 196111c91627..acf1cc2bee07 100644
@@ -47,7 +47,7 @@ struct bma180_part_info {
 
 	u8 int_reset_reg, int_reset_mask;
 	u8 sleep_reg, sleep_mask;
-	u8 bw_reg, bw_mask;
+	u8 bw_reg, bw_mask, bw_offset;
 	u8 scale_reg, scale_mask;
 	u8 power_reg, power_mask, lowpower_val;
 	u8 int_enable_reg, int_enable_mask;

@@ -103,6 +103,7 @@ struct bma180_part_info {
 
 #define BMA250_RANGE_MASK	GENMASK(3, 0) /* Range of accel values */
 #define BMA250_BW_MASK		GENMASK(4, 0) /* Accel bandwidth */
+#define BMA250_BW_OFFSET	8
 #define BMA250_SUSPEND_MASK	BIT(7) /* chip will sleep */
 #define BMA250_LOWPOWER_MASK	BIT(6)
 #define BMA250_DATA_INTEN_MASK	BIT(4)

@@ -241,7 +242,8 @@ static int bma180_set_bw(struct bma180_data *data, int val)
 	for (i = 0; i < data->part_info->num_bw; ++i) {
 		if (data->part_info->bw_table[i] == val) {
 			ret = bma180_set_bits(data, data->part_info->bw_reg,
-				data->part_info->bw_mask, i);
+				data->part_info->bw_mask,
+				i + data->part_info->bw_offset);
 			if (ret) {
 				dev_err(&data->client->dev,
 					"failed to set bandwidth\n");

@@ -669,6 +671,7 @@ static const struct bma180_part_info bma180_part_info[] = {
 		.sleep_mask = BMA250_SUSPEND_MASK,
 		.bw_reg = BMA250_BW_REG,
 		.bw_mask = BMA250_BW_MASK,
+		.bw_offset = BMA250_BW_OFFSET,
 		.scale_reg = BMA250_RANGE_REG,
 		.scale_mask = BMA250_RANGE_MASK,
 		.power_reg = BMA250_POWER_REG,

Signature · 1 line

2.30.2

Greg KH

author maintainer

2021-07-26 09:36 UTC #2 lore raw

Quoted 4 lines · Sudip Mukherjee

Hi Greg,
Quoted 1 line · On Sun, Jul 11, 2021 at 03:01:27PM +0200, [email protected] wrote:

Quoted 9 lines

Quoted 4 lines
The patch below does not apply to the 5.4-stable tree.
If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <[email protected]>.
Here is the backport along with 9436abc40139 ("iio: accel: bma180: Use explicit member assignment") which makes the backporting a little easier. This will apply to all branches till 4.4-stable.

Thanks, both now queued up.

greg k-h