Skip to contentSkip to conversation

Add support to configure beacon tx mode

PATCH In review Maharaja Kennadyrajan 4 participants 12 messages Aug 10, 2021 – Mar 25, 2022

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

v5 cover Add support to configure beacon tx mode

Add support to configure the beacon tx mode as STAGGERED or BURST mode via hostapd configuration during the AP bring-up or via wpa_suppplicant configuration during MESH bring-up.

Beacons can be sent out in burst(continuously in a single shot one after another) or staggered (equally spread out over beacon interval) mode.

V5: Addressed Johannes's and Felix's comment on v4.

V4: Rebased on latest ath.git TOT.

V3: Addressed Johnson's comment on v2 patch.

V2: Addressed Johannes's comment on v1 patch.

Maharaja Kennadyrajan (3):
nl80211: Add support for beacon tx mode
mac80211: Add support for beacon tx mode
ath11k: Add support for beacon tx mode

 drivers/net/wireless/ath/ath11k/mac.c | 10 +++++++---
 include/net/cfg80211.h                |  4 ++++
 include/net/mac80211.h                |  2 ++
 include/uapi/linux/nl80211.h          | 20 ++++++++++++++++++++
 net/mac80211/cfg.c                    |  2 ++
 net/wireless/nl80211.c                | 11 +++++++++++
 6 files changed, 46 insertions(+), 3 deletions(-)
Signature · 7 lines
2.7.4


-- 
ath11k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath11k
#1 lore raw

PATCH v5 1/3 nl80211: Add support for beacon tx mode

User can configure the below beacon tx mode
1. Staggered mode and 2. Burst mode while bring-up the AP or MESH.

Beacons can be sent out in burst(continuously in a single shot one after another) or staggered (equally spread out over beacon interval) mode.

Set the beacon_tx_mode as 1 for Staggered mode and 2 for burst mode.

Hence, added the support in the nl80211/cfg80211 layer to honour the beacon tx mode configuration and pass this value to the driver.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00630-QCAHKSWPL_SILICONZ-2

---

V5: Addressed Johannes's & Felix's comments on v4 patch.

V4: Rebases on latest ath.git TOT.

V3: Addressed Johnson's comment on v2 patch.

V2: Addressed Johannes's comment on v1 patch.

 include/net/cfg80211.h       |  4 ++++
 include/uapi/linux/nl80211.h | 20 ++++++++++++++++++++
 net/wireless/nl80211.c       | 11 +++++++++++
 3 files changed, 35 insertions(+)
include/net/cfg80211.h +4 -0
index 161cdf7..8c3777b 100644
@@ -1189,6 +1189,7 @@ enum cfg80211_ap_settings_flags {
  * @he_oper: HE operation IE (or %NULL if HE isn't enabled)
  * @fils_discovery: FILS discovery transmission parameters
  * @unsol_bcast_probe_resp: Unsolicited broadcast probe response parameters
+ * @beacon_tx_mode: Beacon Tx Mode setting
  */
 struct cfg80211_ap_settings {
 	struct cfg80211_chan_def chandef;
@@ -1221,6 +1222,7 @@ struct cfg80211_ap_settings {
 	struct cfg80211_he_bss_color he_bss_color;
 	struct cfg80211_fils_discovery fils_discovery;
 	struct cfg80211_unsol_bcast_probe_resp unsol_bcast_probe_resp;
+	enum nl80211_beacon_tx_mode beacon_tx_mode;
 };
 
 /**
@@ -2066,6 +2068,7 @@ struct mesh_config {
  *	to operate on DFS channels.
  * @control_port_over_nl80211: TRUE if userspace expects to exchange control
  *	port frames over NL80211 instead of the network interface.
+ * @beacon_tx_mode: Beacon Tx Mode setting.
  *
  * These parameters are fixed when the mesh is created.
  */
@@ -2089,6 +2092,7 @@ struct mesh_setup {
 	struct cfg80211_bitrate_mask beacon_rate;
 	bool userspace_handles_dfs;
 	bool control_port_over_nl80211;
+	enum nl80211_beacon_tx_mode beacon_tx_mode;
 };
 
 /**
include/uapi/linux/nl80211.h +20 -0
index db47499..29c6429 100644
@@ -2560,6 +2560,13 @@ enum nl80211_commands {
  *	disassoc events to indicate that an immediate reconnect to the AP
  *	is desired.
  *
+ * @NL80211_ATTR_BEACON_TX_MODE: used to configure the beacon tx mode (u32),
+ *	as specified in the &enum nl80211_beacon_tx_mode. The user-space
+ *	shall use this attribute to configure the tx mode of beacons.
+ *	Beacons can be sent out in burst(continuously in a single shot
+ *	one after another) or staggered (equally spread out over beacon
+ *	interval) mode.
+ *
  * @NUM_NL80211_ATTR: total number of nl80211_attrs available
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
@@ -3057,6 +3064,8 @@ enum nl80211_attrs {
 
 	NL80211_ATTR_DISABLE_HE,
 
+	NL80211_ATTR_BEACON_TX_MODE,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -7306,4 +7315,15 @@ enum nl80211_sar_specs_attrs {
 	NL80211_SAR_ATTR_SPECS_MAX = __NL80211_SAR_ATTR_SPECS_LAST - 1,
 };
 
+/**
+ * enum nl80211_beacon_tx_mode - Beacon Tx Mode enum.
+ * @NL80211_BEACON_STAGGERED_MODE: Used to configure beacon tx mode as
+ *	staggered mode. This is the default beacon tx mode.
+ * @NL80211_BEACON_BURST_MODE: Used to configure beacon tx mode as burst mode.
+ */
+enum nl80211_beacon_tx_mode {
+	NL80211_BEACON_STAGGERED_MODE = 1,
+	NL80211_BEACON_BURST_MODE = 2,
+};
+
 #endif /* __LINUX_NL80211_H */
net/wireless/nl80211.c +11 -0
index 50eb405..c00e326 100644
@@ -759,6 +759,9 @@ static const struct nla_policy nl80211_policy[NUM_NL80211_ATTR] = {
 	[NL80211_ATTR_RECONNECT_REQUESTED] = { .type = NLA_REJECT },
 	[NL80211_ATTR_SAR_SPEC] = NLA_POLICY_NESTED(sar_policy),
 	[NL80211_ATTR_DISABLE_HE] = { .type = NLA_FLAG },
+	[NL80211_ATTR_BEACON_TX_MODE] =
+		NLA_POLICY_RANGE(NLA_U32, NL80211_BEACON_STAGGERED_MODE,
+				 NL80211_BEACON_BURST_MODE),
 };
 
 /* policy for the key attributes */
@@ -5346,6 +5349,10 @@ static int nl80211_start_ap(struct sk_buff *skb, struct genl_info *info)
 	params.dtim_period =
 		nla_get_u32(info->attrs[NL80211_ATTR_DTIM_PERIOD]);
 
+	if (info->attrs[NL80211_ATTR_BEACON_TX_MODE])
+		params.beacon_tx_mode =
+			nla_get_u32(info->attrs[NL80211_ATTR_BEACON_TX_MODE]);
+
 	err = cfg80211_validate_beacon_int(rdev, dev->ieee80211_ptr->iftype,
 					   params.beacon_interval);
 	if (err)
@@ -11900,6 +11907,10 @@ static int nl80211_join_mesh(struct sk_buff *skb, struct genl_info *info)
 			return -EINVAL;
 	}
 
+	if (info->attrs[NL80211_ATTR_BEACON_TX_MODE])
+		setup.beacon_tx_mode =
+			nla_get_u32(info->attrs[NL80211_ATTR_BEACON_TX_MODE]);
+
 	if (info->attrs[NL80211_ATTR_MESH_SETUP]) {
 		/* parse additional setup parameters if given */
 		err = nl80211_parse_mesh_setup(info, &setup);
Signature · 7 lines
2.7.4


-- 
ath11k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath11k
#2 lore raw

Re: [PATCH v5 1/3] nl80211: Add support for beacon tx mode

Quoted 10 lines · Maharaja Kennadyrajan

User can configure the below beacon tx mode
1. Staggered mode and 2. Burst mode while bring-up the AP or MESH.

Beacons can be sent out in burst(continuously in a single shot one after another) or staggered (equally spread out over beacon interval) mode.

Set the beacon_tx_mode as 1 for Staggered mode and 2 for burst mode.

What's the advantage of one over the other? When and why would the user choose a different mode other than the default?

- Felix

#3 lore raw

Re: [PATCH v5 1/3] nl80211: Add support for beacon tx mode

Quoted 5 lines · Felix Fietkau
Quoted 4 lines · Maharaja Kennadyrajan

User can configure the below beacon tx mode
1. Staggered mode and 2. Burst mode while bring-up the AP or MESH.

Quoted 9 lines
Quoted 6 lines

Beacons can be sent out in burst(continuously in a single shot one after another) or staggered (equally spread out over beacon interval) mode.

Set the beacon_tx_mode as 1 for Staggered mode and 2 for burst mode.

What's the advantage of one over the other? When and why would the user choose a different mode other than the default?

[Maha]: In the multi-vap scenario and default or staggered mode, tx failure of the packets will happen if the packets duration is greater than the beacon interval between the two vaps. In case of burst mode it works, where during retry it transmits the packet.

Quoted 1 line

- Felix

Signature · 3 lines
ath11k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath11k
#4 lore raw

Re: [PATCH v5 1/3] nl80211: Add support for beacon tx mode

Quoted 12 lines · Maharaja Kennadyrajan
Quoted 11 lines · Felix Fietkau
Quoted 10 lines · Maharaja Kennadyrajan

User can configure the below beacon tx mode
1. Staggered mode and 2. Burst mode while bring-up the AP or MESH.

Beacons can be sent out in burst(continuously in a single shot one after another) or staggered (equally spread out over beacon interval) mode.

Set the beacon_tx_mode as 1 for Staggered mode and 2 for burst mode.

Quoted 8 lines
Quoted 3 lines

What's the advantage of one over the other? When and why would the user choose a different mode other than the default?

[Maha]: In the multi-vap scenario and default or staggered mode, tx failure of the packets will happen if the packets duration is greater than the beacon interval between the two vaps. In case of burst mode it works, where during retry it transmits the packet.

It still seems to me like something that the driver should detect and handle internally without user configuration, based on number of VAPs and maybe multicast/beacon rate (since the packet duration issue will be worse with CCK rates).

- Felix

#5 lore raw

Re: [PATCH v5 1/3] nl80211: Add support for beacon tx mode

In reply to Maharaja Kennadyrajan
Quoted 2 lines · On Tuesday, 10 August 2021 10:56:21 CEST Maharaja Kennadyrajan wrote:

1. Staggered mode and 2. Burst mode while bring-up the AP or MESH.

Why when you bring up mesh or AP when it is actually a global setting for this radio/PHY?

Kind regards,
Sven

#6 lore raw

Re: [PATCH v5 1/3] nl80211: Add support for beacon tx mode

Quoted 6 lines · Sven Eckelmann
Quoted 2 lines · On Tuesday, 10 August 2021 10:56:21 CEST Maharaja Kennadyrajan wrote:

1. Staggered mode and 2. Burst mode while bring-up the AP or MESH.

Why when you bring up mesh or AP when it is actually a global setting for this radio/PHY?

[Maha]: yes, it is radio/PHY setting only and it is supported for AP and MESH mode now.

Quoted 3 lines

Kind regards,
Sven

#7 lore raw

Re: [PATCH v5 1/3] nl80211: Add support for beacon tx mode

Quoted 2 lines · On Thursday, 24 March 2022 19:10:20 CET Maharaja Kennadyrajan wrote:

[Maha]: yes, it is radio/PHY setting only and it is supported for AP and MESH mode now.

But why are you setting it by vif when it is actually a PHY setting?

Kind regards,
Sven

Signature · 3 lines
ath11k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath11k
#8 lore raw

Re: [PATCH v5 1/3] nl80211: Add support for beacon tx mode

In reply to Maharaja Kennadyrajan
Quoted 76 lines · Maharaja Kennadyrajan

User can configure the below beacon tx mode
1. Staggered mode and 2. Burst mode while bring-up the AP or MESH.

Beacons can be sent out in burst(continuously in a single shot one after another) or staggered (equally spread out over beacon interval) mode.

Set the beacon_tx_mode as 1 for Staggered mode and 2 for burst mode.

Hence, added the support in the nl80211/cfg80211 layer to honour the beacon tx mode configuration and pass this value to the driver.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00630-QCAHKSWPL_SILICONZ-2

---

V5: Addressed Johannes's & Felix's comments on v4 patch.

V4: Rebases on latest ath.git TOT.

V3: Addressed Johnson's comment on v2 patch.

V2: Addressed Johannes's comment on v1 patch.

 include/net/cfg80211.h       |  4 ++++
 include/uapi/linux/nl80211.h | 20 ++++++++++++++++++++
 net/wireless/nl80211.c       | 11 +++++++++++
 3 files changed, 35 insertions(+)
include/net/cfg80211.h +0 -0
index 161cdf7..8c3777b 100644
@@ -1189,6 +1189,7 @@ enum cfg80211_ap_settings_flags {
  * @he_oper: HE operation IE (or %NULL if HE isn't enabled)
  * @fils_discovery: FILS discovery transmission parameters
  * @unsol_bcast_probe_resp: Unsolicited broadcast probe response

parameters
+ * @beacon_tx_mode: Beacon Tx Mode setting
*/
struct cfg80211_ap_settings {

include/net/cfg80211.h +1 -0
 	struct cfg80211_chan_def chandef;
@@ -1221,6 +1222,7 @@ struct cfg80211_ap_settings {
 	struct cfg80211_he_bss_color he_bss_color;
 	struct cfg80211_fils_discovery fils_discovery;
 	struct cfg80211_unsol_bcast_probe_resp unsol_bcast_probe_resp;
+	enum nl80211_beacon_tx_mode beacon_tx_mode;
 };
 
 /**
@@ -2066,6 +2068,7 @@ struct mesh_config {
  *	to operate on DFS channels.
  * @control_port_over_nl80211: TRUE if userspace expects to exchange

control
* port frames over NL80211 instead of the network interface.
+ * @beacon_tx_mode: Beacon Tx Mode setting.
*
* These parameters are fixed when the mesh is created. */

include/net/cfg80211.h +1 -0
@@ -2089,6 +2092,7 @@ struct mesh_setup {
 	struct cfg80211_bitrate_mask beacon_rate;
 	bool userspace_handles_dfs;
 	bool control_port_over_nl80211;
+	enum nl80211_beacon_tx_mode beacon_tx_mode;
 };
 
 /**
include/uapi/linux/nl80211.h +0 -0
index db47499..29c6429 100644

include/uapi/linux/nl80211.h enum nl80211_commands { · line 2566

Quoted 7 lines
include/uapi/linux/nl80211.h +3 -0
@@ -2560,6 +2560,13 @@ enum nl80211_commands {
  *	disassoc events to indicate that an immediate reconnect to the AP
  *	is desired.
  *
+ * @NL80211_ATTR_BEACON_TX_MODE: used to configure the beacon tx mode
 (u32),
+ *	as specified in the &enum nl80211_beacon_tx_mode. The user-space
+ *	shall use this attribute to configure the tx mode of beacons.

s/shall/can/
'shall' implies a required action whereas 'can' implies an optional action

Quoted 25 lines
include/uapi/linux/nl80211.h +4 -0
+ *	Beacons can be sent out in burst(continuously in a single shot
+ *	one after another) or staggered (equally spread out over beacon
+ *	interval) mode.
+ *
  * @NUM_NL80211_ATTR: total number of nl80211_attrs available
  * @NL80211_ATTR_MAX: highest attribute number currently defined

* @__NL80211_ATTR_AFTER_LAST: internal use

include/uapi/linux/nl80211.h +7 -0
@@ -3057,6 +3064,8 @@ enum nl80211_attrs {
 
 	NL80211_ATTR_DISABLE_HE,
 
+	NL80211_ATTR_BEACON_TX_MODE,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -7306,4 +7315,15 @@ enum nl80211_sar_specs_attrs {
 	NL80211_SAR_ATTR_SPECS_MAX = __NL80211_SAR_ATTR_SPECS_LAST - 1,
 };
 
+/**
+ * enum nl80211_beacon_tx_mode - Beacon Tx Mode enum.
+ * @NL80211_BEACON_STAGGERED_MODE: Used to configure beacon tx mode as
+ *	staggered mode. This is the default beacon tx mode.
+ * @NL80211_BEACON_BURST_MODE: Used to configure beacon tx mode as 
Quoted 4 lines

burst
mode.
+ */
+enum nl80211_beacon_tx_mode {

what happened to 0?

now we're back to the issue that I originally reported that if the attribute is not present you send 0 to the driver which is not a valid enumeration See my additional comments further below

Quoted 35 lines
include/uapi/linux/nl80211.h +4 -0
+	NL80211_BEACON_STAGGERED_MODE = 1,
+	NL80211_BEACON_BURST_MODE = 2,
+};
+
 #endif /* __LINUX_NL80211_H */
net/wireless/nl80211.c +3 -0
index 50eb405..c00e326 100644
@@ -759,6 +759,9 @@ static const struct nla_policy
 nl80211_policy[NUM_NL80211_ATTR] = {
 	[NL80211_ATTR_RECONNECT_REQUESTED] = { .type = NLA_REJECT },
 	[NL80211_ATTR_SAR_SPEC] = NLA_POLICY_NESTED(sar_policy),
 	[NL80211_ATTR_DISABLE_HE] = { .type = NLA_FLAG },
+	[NL80211_ATTR_BEACON_TX_MODE] =
+		NLA_POLICY_RANGE(NLA_U32, NL80211_BEACON_STAGGERED_MODE,
+				 NL80211_BEACON_BURST_MODE),
 };
 

/* policy for the key attributes */

net/wireless/nl80211.c +4 -0
@@ -5346,6 +5349,10 @@ static int nl80211_start_ap(struct sk_buff *skb,
 struct genl_info *info)
 	params.dtim_period =
 		nla_get_u32(info->attrs[NL80211_ATTR_DTIM_PERIOD]);
 
+	if (info->attrs[NL80211_ATTR_BEACON_TX_MODE])
+		params.beacon_tx_mode =
+
 nla_get_u32(info->attrs[NL80211_ATTR_BEACON_TX_MODE]);
+
 	err = cfg80211_validate_beacon_int(rdev,

dev->ieee80211_ptr->iftype,

net/wireless/nl80211.c +0 -0
 					   params.beacon_interval);
 	if (err)

net/wireless/nl80211.c static int nl80211_join_mesh(struct sk_buff · line 11916

Quoted 10 lines
net/wireless/nl80211.c +4 -0
@@ -11900,6 +11907,10 @@ static int nl80211_join_mesh(struct sk_buff 
 *skb,
 struct genl_info *info)
 			return -EINVAL;
 	}
 
+	if (info->attrs[NL80211_ATTR_BEACON_TX_MODE])
+		setup.beacon_tx_mode =
+
 nla_get_u32(info->attrs[NL80211_ATTR_BEACON_TX_MODE]);
+

if you are not going to have an enum for default = 0 then you need an else to set beacon_tx_mode = NL80211_BEACON_STAGGERED_MODE

Quoted 5 lines
net/wireless/nl80211.c +0 -1
 	if (info->attrs[NL80211_ATTR_MESH_SETUP]) {
 		/* parse additional setup parameters if given */
 		err = nl80211_parse_mesh_setup(info, &setup);
--

2.7.4

Signature · 7 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

-- 
ath11k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath11k
#9 lore raw

PATCH v5 2/3 mac80211: Add support for beacon tx mode

In reply to Maharaja Kennadyrajan

Pass the beacon tx mode value from the nl80211/cfg80211 layer to the driver via ieee80211_ops and driver ops.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00480-QCAHKSWPL_SILICONZ-1

---
 include/net/mac80211.h | 2 ++
 net/mac80211/cfg.c     | 2 ++
 2 files changed, 4 insertions(+)
include/net/mac80211.h +2 -0
index d8a1d09..082fc17 100644
@@ -632,6 +632,7 @@ struct ieee80211_fils_discovery {
  * @s1g: BSS is S1G BSS (affects Association Request format).
  * @beacon_tx_rate: The configured beacon transmit rate that needs to be passed
  *	to driver when rate control is offloaded to firmware.
+ * @beacon_tx_mode: Beacon Tx Mode setting.
  */
 struct ieee80211_bss_conf {
 	const u8 *bssid;
@@ -702,6 +703,7 @@ struct ieee80211_bss_conf {
 	u32 unsol_bcast_probe_resp_interval;
 	bool s1g;
 	struct cfg80211_bitrate_mask beacon_tx_rate;
+	enum nl80211_beacon_tx_mode beacon_tx_mode;
 };
 
 /**
net/mac80211/cfg.c +2 -0
index 84cc773..9ae03ef 100644
@@ -1063,6 +1063,7 @@ static int ieee80211_start_ap(struct wiphy *wiphy, struct net_device *dev,
 
 	prev_beacon_int = sdata->vif.bss_conf.beacon_int;
 	sdata->vif.bss_conf.beacon_int = params->beacon_interval;
+	sdata->vif.bss_conf.beacon_tx_mode = params->beacon_tx_mode;
 
 	if (params->he_cap && params->he_oper) {
 		sdata->vif.bss_conf.he_support = true;
@@ -2119,6 +2120,7 @@ static int copy_mesh_setup(struct ieee80211_if_mesh *ifmsh,
 
 	sdata->vif.bss_conf.beacon_int = setup->beacon_interval;
 	sdata->vif.bss_conf.dtim_period = setup->dtim_period;
+	sdata->vif.bss_conf.beacon_tx_mode = setup->beacon_tx_mode;
 
 	sdata->beacon_rate_set = false;
 	if (wiphy_ext_feature_isset(sdata->local->hw.wiphy,
Signature · 1 line
2.7.4
#10 lore raw

PATCH v5 3/3 ath11k: Add support for beacon tx mode

In reply to Maharaja Kennadyrajan

Add support to configure the beacon tx mode in
the driver.

Beacons can be sent out in burst(continuously in a single shot one after another) or staggered (equally spread out over beacon interval) mode.

Use the below configuration in the hostapd/wpa_supplicant for AP/MESH mode to configure the beacon tx mode.

"beacon_tx_mode=N", where N = 1 for STAGGERED beacon mode and N = 2 for BURST beacon mode.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00480-QCAHKSWPL_SILICONZ-1

---
 drivers/net/wireless/ath/ath11k/mac.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)
drivers/net/wireless/ath/ath11k/mac.c +7 -3
index e9b3689..2eda788 100644
@@ -2136,7 +2136,10 @@ static void ath11k_mac_op_bss_info_changed(struct ieee80211_hw *hw,
 
 	if (changed & BSS_CHANGED_BEACON) {
 		param_id = WMI_PDEV_PARAM_BEACON_TX_MODE;
-		param_value = WMI_BEACON_STAGGERED_MODE;
+		if (info->beacon_tx_mode == NL80211_BEACON_BURST_MODE)
+			param_value = WMI_BEACON_BURST_MODE;
+		else
+			param_value = WMI_BEACON_STAGGERED_MODE;
 		ret = ath11k_wmi_pdev_set_param(ar, param_id,
 						param_value, ar->pdev->pdev_id);
 		if (ret)
@@ -2144,8 +2147,9 @@ static void ath11k_mac_op_bss_info_changed(struct ieee80211_hw *hw,
 				    arvif->vdev_id);
 		else
 			ath11k_dbg(ar->ab, ATH11K_DBG_MAC,
-				   "Set staggered beacon mode for VDEV: %d\n",
-				   arvif->vdev_id);
+				   "Set %s beacon mode for VDEV: %d mode: %d\n",
+				   param_value ? "burst" : "staggered",
+				   arvif->vdev_id, param_value);
 
 		ret = ath11k_mac_setup_bcn_tmpl(arvif);
 		if (ret)
Signature · 1 line
2.7.4
#11 lore raw

Re: [PATCH v5 3/3] ath11k: Add support for beacon tx mode

Quoted 41 lines · Maharaja Kennadyrajan

Add support to configure the beacon tx mode in
the driver.

Beacons can be sent out in burst(continuously in a single shot one after another) or staggered (equally spread out over beacon interval) mode.

Use the below configuration in the hostapd/wpa_supplicant for AP/MESH mode to configure the beacon tx mode.

"beacon_tx_mode=N", where N = 1 for STAGGERED beacon mode and N = 2 for BURST beacon mode.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00480-QCAHKSWPL_SILICONZ-1

---
 drivers/net/wireless/ath/ath11k/mac.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)
drivers/net/wireless/ath/ath11k/mac.c +0 -0
index e9b3689..2eda788 100644
@@ -2136,7 +2136,10 @@ static void 

ath11k_mac_op_bss_info_changed(struct
ieee80211_hw *hw,

drivers/net/wireless/ath/ath11k/mac.c +4 -1
 	if (changed & BSS_CHANGED_BEACON) {
 		param_id = WMI_PDEV_PARAM_BEACON_TX_MODE;
-		param_value = WMI_BEACON_STAGGERED_MODE;
+		if (info->beacon_tx_mode == NL80211_BEACON_BURST_MODE)
+			param_value = WMI_BEACON_BURST_MODE;
+		else
+			param_value = WMI_BEACON_STAGGERED_MODE;
 		ret = ath11k_wmi_pdev_set_param(ar, param_id,
 						param_value,

ar->pdev->pdev_id);

drivers/net/wireless/ath/ath11k/mac.c +0 -0
 		if (ret)

drivers/net/wireless/ath/ath11k/mac.c static void ath11k_mac_op_bss_info_changed(struct · line 2154

Quoted 10 lines
drivers/net/wireless/ath/ath11k/mac.c +2 -2
@@ -2144,8 +2147,9 @@ static void ath11k_mac_op_bss_info_changed(struct
 ieee80211_hw *hw,
 				    arvif->vdev_id);
 		else
 			ath11k_dbg(ar->ab, ATH11K_DBG_MAC,
-				   "Set staggered beacon mode for VDEV:
 %d\n",
-				   arvif->vdev_id);
+				   "Set %s beacon mode for VDEV: %d mode:
 %d\n",
+				   param_value ? "burst" : "staggered",

Suggest this should be param_value == WMI_BEACON_BURST_MODE ?
or other similar logic since ideally code should avoid making assumptions about the values assigned to enumerators

Quoted 6 lines
drivers/net/wireless/ath/ath11k/mac.c +1 -0
+				   arvif->vdev_id, param_value);
drivers/net/wireless/ath/ath11k/mac.c +0 -1
 		ret = ath11k_mac_setup_bcn_tmpl(arvif);
 		if (ret)
--

2.7.4

Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project