Skip to contentSkip to conversation

dt-bindings: usb: mtk-xhci: add optional property to disable usb2 ports

PATCH RESEND In review Chunfeng Yun 2 participants 10 messages Aug 17, 2021 – Aug 18, 2021

Subsystems (6)
lore
Share & tools
lore

Chunfeng Yun

author maintainer
#0 lore raw

PATCH RESEND 1/9 dt-bindings: usb: mtk-xhci: add optional property to disable usb2 ports

Add support to disable specific usb2 host ports, it's useful when a usb2 port is disabled on some platforms, but enabled on others for the same SoC, another case is that the different package may support different number of ports.

---
 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml | 5 +++++
 1 file changed, 5 insertions(+)
Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml +5 -0
index 49729aab6d1a..61a0e550b5d6 100644
@@ -154,6 +154,11 @@ properties:
     description: The mask to disable u3ports, bit0 for u3port0,
       bit1 for u3port1, ... etc
 
+  mediatek,u2p-dis-msk:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: The mask to disable u2ports, bit0 for u2port0,
+      bit1 for u2port1, ... etc
+
   "#address-cells":
     const: 1
 
Signature · 1 line
2.18.0
author maintainer
#1 lore raw

PATCH RESEND 2/9 dt-bindings: usb: mtk-xhci: add compatible for mt8195

There are 4 USB controllers on MT8195, the controllers (IP1~IP3, exclude IP0) have a wrong default SOF/ITP interval which is calculated from the frame counter clock 24Mhz by default, but in fact, the frame counter clock is 48Mhz, so we should set the accurate interval according to 48Mhz. Here add a new compatible for MT8195, it's also supported in driver. But the first controller (IP0) has no such issue, we prefer to use generic compatible, e.g. mt8192's compatible.

---
 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml +1 -0
index 61a0e550b5d6..753e043e5327 100644
@@ -31,6 +31,7 @@ properties:
           - mediatek,mt8173-xhci
           - mediatek,mt8183-xhci
           - mediatek,mt8192-xhci
+          - mediatek,mt8195-xhci
       - const: mediatek,mtk-xhci
 
   reg:
Signature · 1 line
2.18.0
author maintainer
#2 lore raw

PATCH RESEND 3/9 usb: xhci-mtk: fix use-after-free of mtk->hcd

In reply to Chunfeng Yun
 BUG: KASAN: use-after-free in usb_hcd_is_primary_hcd+0x38/0x60
 Call trace:
  dump_backtrace+0x0/0x3dc
  show_stack+0x20/0x2c
  dump_stack+0x15c/0x1d4
  print_address_description+0x7c/0x510
  kasan_report+0x164/0x1ac
  __asan_report_load8_noabort+0x44/0x50
  usb_hcd_is_primary_hcd+0x38/0x60
  xhci_mtk_runtime_suspend+0x68/0x148
  pm_generic_runtime_suspend+0x90/0xac
  __rpm_callback+0xb8/0x1f4
  rpm_callback+0x54/0x1d0
  rpm_suspend+0x4e0/0xc84
  __pm_runtime_suspend+0xc4/0x114
  xhci_mtk_probe+0xa58/0xd00

This may happen when probe fails, needn't suspend it synchronously, fix it by using pm_runtime_put_noidle().

---
 drivers/usb/host/xhci-mtk.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/usb/host/xhci-mtk.c +1 -1
index d66b6a8b59ba..f6d161670c4e 100644
@@ -573,7 +573,7 @@ static int xhci_mtk_probe(struct platform_device *pdev)
 	xhci_mtk_ldos_disable(mtk);
 
 disable_pm:
-	pm_runtime_put_sync_autosuspend(dev);
+	pm_runtime_put_noidle(dev);
 	pm_runtime_disable(dev);
 	return ret;
 }
Signature · 1 line
2.18.0
author maintainer
#3 lore raw

PATCH RESEND 4/9 usb: xhci-mtk: support option to disable usb2 ports

In reply to Chunfeng Yun

Add support to disable specific usb2 host ports, it's useful when a usb2 port is disabled on some platforms, but enabled on others for the same SoC.

---
 drivers/usb/host/xhci-mtk.c | 12 ++++++++++--
 drivers/usb/host/xhci-mtk.h |  1 +
 2 files changed, 11 insertions(+), 2 deletions(-)
drivers/usb/host/xhci-mtk.c +10 -2
index f6d161670c4e..12b691547438 100644
@@ -116,8 +116,11 @@ static int xhci_mtk_host_enable(struct xhci_hcd_mtk *mtk)
 		writel(value, &ippc->u3_ctrl_p[i]);
 	}
 
-	/* power on and enable all u2 ports */
+	/* power on and enable all u2 ports except skipped ones */
 	for (i = 0; i < mtk->num_u2_ports; i++) {
+		if (BIT(i) & mtk->u2p_dis_msk)
+			continue;
+
 		value = readl(&ippc->u2_ctrl_p[i]);
 		value &= ~(CTRL_U2_PORT_PDN | CTRL_U2_PORT_DIS);
 		value |= CTRL_U2_PORT_HOST_SEL;
@@ -164,8 +167,11 @@ static int xhci_mtk_host_disable(struct xhci_hcd_mtk *mtk)
 		writel(value, &ippc->u3_ctrl_p[i]);
 	}
 
-	/* power down all u2 ports */
+	/* power down all u2 ports except skipped ones */
 	for (i = 0; i < mtk->num_u2_ports; i++) {
+		if (BIT(i) & mtk->u2p_dis_msk)
+			continue;
+
 		value = readl(&ippc->u2_ctrl_p[i]);
 		value |= CTRL_U2_PORT_PDN;
 		writel(value, &ippc->u2_ctrl_p[i]);
@@ -445,6 +451,8 @@ static int xhci_mtk_probe(struct platform_device *pdev)
 	/* optional property, ignore the error if it does not exist */
 	of_property_read_u32(node, "mediatek,u3p-dis-msk",
 			     &mtk->u3p_dis_msk);
+	of_property_read_u32(node, "mediatek,u2p-dis-msk",
+			     &mtk->u2p_dis_msk);
 
 	ret = usb_wakeup_of_property_parse(mtk, node);
 	if (ret) {
drivers/usb/host/xhci-mtk.h +1 -0
index ace432356c41..0466bc8f7500 100644
@@ -138,6 +138,7 @@ struct xhci_hcd_mtk {
 	struct mu3c_ippc_regs __iomem *ippc_regs;
 	int num_u2_ports;
 	int num_u3_ports;
+	int u2p_dis_msk;
 	int u3p_dis_msk;
 	struct regulator *vusb33;
 	struct regulator *vbus;
Signature · 1 line
2.18.0
author maintainer
#4 lore raw

PATCH RESEND 5/9 usb: xhci-mtk: fix issue of out-of-bounds array access

In reply to Chunfeng Yun

Bus bandwidth array access is based on esit, increase one will cause out-of-bounds issue; for example, when esit is XHCI_MTK_MAX_ESIT, will overstep boundary.

Fixes 7c986fbc16ae ("usb: xhci-mtk: get the microframe boundary for ESIT")
---
 drivers/usb/host/xhci-mtk-sch.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/usb/host/xhci-mtk-sch.c +6 -4
index cffcaf4dfa9f..0bb1a6295d64 100644
@@ -575,10 +575,12 @@ static u32 get_esit_boundary(struct mu3h_sch_ep_info *sch_ep)
 	u32 boundary = sch_ep->esit;
 
 	if (sch_ep->sch_tt) { /* LS/FS with TT */
-		/* tune for CS */
-		if (sch_ep->ep_type != ISOC_OUT_EP)
-			boundary++;
-		else if (boundary > 1) /* normally esit >= 8 for FS/LS */
+		/*
+		 * tune for CS, normally esit >= 8 for FS/LS,
+		 * not add one for other types to avoid access array
+		 * out of boundary
+		 */
+		if (sch_ep->ep_type == ISOC_OUT_EP && boundary > 1)
 			boundary--;
 	}
 
Signature · 1 line
2.18.0
author maintainer
#5 lore raw

PATCH RESEND 6/9 usb: xhci-mtk: update fs bus bandwidth by bw_budget_table

In reply to Chunfeng Yun

Use @bw_budget_table[] to update fs bus bandwidth due to not all microframes consume @bw_cost_per_microframe, see setup_sch_info().

---
 drivers/usb/host/xhci-mtk-sch.c | 17 +++++++----------
 1 file changed, 7 insertions(+), 10 deletions(-)
drivers/usb/host/xhci-mtk-sch.c +7 -10
index 0bb1a6295d64..10c0f0f6461f 100644
@@ -458,8 +458,8 @@ static int check_fs_bus_bw(struct mu3h_sch_ep_info *sch_ep, int offset)
 		 * Compared with hs bus, no matter what ep type,
 		 * the hub will always delay one uframe to send data
 		 */
-		for (j = 0; j < sch_ep->cs_count; j++) {
-			tmp = tt->fs_bus_bw[base + j] + sch_ep->bw_cost_per_microframe;
+		for (j = 0; j < sch_ep->num_budget_microframes; j++) {
+			tmp = tt->fs_bus_bw[base + j] + sch_ep->bw_budget_table[j];
 			if (tmp > FS_PAYLOAD_MAX)
 				return -ESCH_BW_OVERFLOW;
 		}
@@ -534,21 +534,18 @@ static void update_sch_tt(struct mu3h_sch_ep_info *sch_ep, bool used)
 {
 	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
 	u32 base, num_esit;
-	int bw_updated;
 	int i, j;
 
 	num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
 
-	if (used)
-		bw_updated = sch_ep->bw_cost_per_microframe;
-	else
-		bw_updated = -sch_ep->bw_cost_per_microframe;
-
 	for (i = 0; i < num_esit; i++) {
 		base = sch_ep->offset + i * sch_ep->esit;
 
-		for (j = 0; j < sch_ep->cs_count; j++)
-			tt->fs_bus_bw[base + j] += bw_updated;
+		for (j = 0; j < sch_ep->num_budget_microframes; j++)
+			if (used)
+				tt->fs_bus_bw[base + j] += sch_ep->bw_budget_table[j];
+			else
+				tt->fs_bus_bw[base + j] -= sch_ep->bw_budget_table[j];
 	}
 
 	if (used)
Signature · 1 line
2.18.0
author maintainer
#6 lore raw

PATCH RESEND 7/9 usb: xhci-mtk: check boundary before check tt

In reply to Chunfeng Yun

check_sch_tt() will access fs_bus_bw[] array, check boundary firstly to avoid out-of-bounds issue.

---
 drivers/usb/host/xhci-mtk-sch.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/usb/host/xhci-mtk-sch.c +4 -3
index 10c0f0f6461f..c2f13d69c607 100644
@@ -600,13 +600,14 @@ static int check_sch_bw(struct mu3h_sch_bw_info *sch_bw,
 	 * and find a microframe where its worst bandwidth is minimum.
 	 */
 	for (offset = 0; offset < sch_ep->esit; offset++) {
-		ret = check_sch_tt(sch_ep, offset);
-		if (ret)
-			continue;
 
 		if ((offset + sch_ep->num_budget_microframes) > esit_boundary)
 			break;
 
+		ret = check_sch_tt(sch_ep, offset);
+		if (ret)
+			continue;
+
 		worst_bw = get_max_bw(sch_bw, sch_ep, offset);
 		if (worst_bw > bw_boundary)
 			continue;
Signature · 1 line
2.18.0
author maintainer
#7 lore raw

PATCH RESEND 8/9 usb: xhci-mtk: add a member of num_esit

In reply to Chunfeng Yun

Add a member num_esit to save the number of esit, then no need caculate it in some functions.

---
 drivers/usb/host/xhci-mtk-sch.c | 20 +++++++-------------
 drivers/usb/host/xhci-mtk.h     |  2 ++
 2 files changed, 9 insertions(+), 13 deletions(-)
drivers/usb/host/xhci-mtk-sch.c +7 -13
index c2f13d69c607..a9fcf7e30c41 100644
@@ -297,6 +297,7 @@ static void setup_sch_info(struct xhci_ep_ctx *ep_ctx,
 		 CTX_TO_MAX_ESIT_PAYLOAD(le32_to_cpu(ep_ctx->tx_info));
 
 	sch_ep->esit = get_esit(ep_ctx);
+	sch_ep->num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
 	sch_ep->ep_type = ep_type;
 	sch_ep->maxpkt = maxpkt;
 	sch_ep->offset = 0;
@@ -401,14 +402,12 @@ static void setup_sch_info(struct xhci_ep_ctx *ep_ctx,
 static u32 get_max_bw(struct mu3h_sch_bw_info *sch_bw,
 	struct mu3h_sch_ep_info *sch_ep, u32 offset)
 {
-	u32 num_esit;
 	u32 max_bw = 0;
 	u32 bw;
 	int i;
 	int j;
 
-	num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
-	for (i = 0; i < num_esit; i++) {
+	for (i = 0; i < sch_ep->num_esit; i++) {
 		u32 base = offset + i * sch_ep->esit;
 
 		for (j = 0; j < sch_ep->num_budget_microframes; j++) {
@@ -424,13 +423,11 @@ static u32 get_max_bw(struct mu3h_sch_bw_info *sch_bw,
 static void update_bus_bw(struct mu3h_sch_bw_info *sch_bw,
 	struct mu3h_sch_ep_info *sch_ep, bool used)
 {
-	u32 num_esit;
 	u32 base;
 	int i;
 	int j;
 
-	num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
-	for (i = 0; i < num_esit; i++) {
+	for (i = 0; i < sch_ep->num_esit; i++) {
 		base = sch_ep->offset + i * sch_ep->esit;
 		for (j = 0; j < sch_ep->num_budget_microframes; j++) {
 			if (used)
@@ -446,12 +443,11 @@ static void update_bus_bw(struct mu3h_sch_bw_info *sch_bw,
 static int check_fs_bus_bw(struct mu3h_sch_ep_info *sch_ep, int offset)
 {
 	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
-	u32 num_esit, tmp;
+	u32 tmp;
 	int base;
 	int i, j;
 
-	num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
-	for (i = 0; i < num_esit; i++) {
+	for (i = 0; i < sch_ep->num_esit; i++) {
 		base = offset + i * sch_ep->esit;
 
 		/*
@@ -533,12 +529,10 @@ static int check_sch_tt(struct mu3h_sch_ep_info *sch_ep, u32 offset)
 static void update_sch_tt(struct mu3h_sch_ep_info *sch_ep, bool used)
 {
 	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
-	u32 base, num_esit;
+	u32 base;
 	int i, j;
 
-	num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
-
-	for (i = 0; i < num_esit; i++) {
+	for (i = 0; i < sch_ep->num_esit; i++) {
 		base = sch_ep->offset + i * sch_ep->esit;
 
 		for (j = 0; j < sch_ep->num_budget_microframes; j++)
drivers/usb/host/xhci-mtk.h +2 -0
index 0466bc8f7500..56dc348349af 100644
@@ -50,6 +50,7 @@ struct mu3h_sch_bw_info {
  * struct mu3h_sch_ep_info: schedule information for endpoint
  *
  * @esit: unit is 125us, equal to 2 << Interval field in ep-context
+ * @num_esit: number of @esit in a period
  * @num_budget_microframes: number of continuous uframes
  *		(@repeat==1) scheduled within the interval
  * @bw_cost_per_microframe: bandwidth cost per microframe
@@ -79,6 +80,7 @@ struct mu3h_sch_bw_info {
  */
 struct mu3h_sch_ep_info {
 	u32 esit;
+	u32 num_esit;
 	u32 num_budget_microframes;
 	u32 bw_cost_per_microframe;
 	struct list_head endpoint;
Signature · 1 line
2.18.0
author maintainer
#8 lore raw

PATCH RESEND 9/9 usb: xhci-mtk: modify the SOF/ITP interval for mt8195

In reply to Chunfeng Yun

There are 4 USB controllers on MT8195, the controllers (IP1~IP3, exclude IP0) have a wrong default SOF/ITP interval which is calculated from the frame counter clock 24Mhz by default, but in fact, the frame counter clock is 48Mhz, so we should set the accurate interval according to 48Mhz for those controllers.
Note: the first controller no need set it.

---
 drivers/usb/host/xhci-mtk.c | 65 +++++++++++++++++++++++++++++++++++++
 1 file changed, 65 insertions(+)
drivers/usb/host/xhci-mtk.c +65 -0
index 12b691547438..7ff0cd707ba1 100644
@@ -57,6 +57,27 @@
 /* u2_phy_pll register */
 #define CTRL_U2_FORCE_PLL_STB	BIT(28)
 
+/* xHCI CSR */
+#define LS_EOF_CFG		0x930
+#define LSEOF_OFFSET		0x89
+
+#define FS_EOF_CFG		0x934
+#define FSEOF_OFFSET		0x2e
+
+#define SS_GEN1_EOF_CFG		0x93c
+#define SSG1EOF_OFFSET		0x78
+
+#define HFCNTR_CFG		0x944
+#define ITP_DELTA_CLK		(0xa << 1)
+#define ITP_DELTA_CLK_MASK	GENMASK(5, 1)
+#define FRMCNT_LEV1_RANG	(0x12b << 8)
+#define FRMCNT_LEV1_RANG_MASK	GENMASK(19, 8)
+
+#define SS_GEN2_EOF_CFG		0x990
+#define SSG2EOF_OFFSET		0x3c
+
+#define XSEOF_OFFSET_MASK	GENMASK(11, 0)
+
 /* usb remote wakeup registers in syscon */
 
 /* mt8173 etc */
@@ -87,6 +108,46 @@ enum ssusb_uwk_vers {
 	SSUSB_UWK_V1_2,		/* specific revision 1.2 */
 };
 
+/*
+ * MT8195 has 4 controllers, the controller1~3's default SOF/ITP interval
+ * is calculated from the frame counter clock 24M, but in fact, the clock
+ * is 48M, add workaround for it.
+ */
+static void xhci_mtk_set_frame_interval(struct xhci_hcd_mtk *mtk)
+{
+	struct device *dev = mtk->dev;
+	struct usb_hcd *hcd = mtk->hcd;
+	u32 value;
+
+	if (!of_device_is_compatible(dev->of_node, "mediatek,mt8195-xhci"))
+		return;
+
+	value = readl(hcd->regs + HFCNTR_CFG);
+	value &= ~(ITP_DELTA_CLK_MASK | FRMCNT_LEV1_RANG_MASK);
+	value |= (ITP_DELTA_CLK | FRMCNT_LEV1_RANG);
+	writel(value, hcd->regs + HFCNTR_CFG);
+
+	value = readl(hcd->regs + LS_EOF_CFG);
+	value &= ~XSEOF_OFFSET_MASK;
+	value |= LSEOF_OFFSET;
+	writel(value, hcd->regs + LS_EOF_CFG);
+
+	value = readl(hcd->regs + FS_EOF_CFG);
+	value &= ~XSEOF_OFFSET_MASK;
+	value |= FSEOF_OFFSET;
+	writel(value, hcd->regs + FS_EOF_CFG);
+
+	value = readl(hcd->regs + SS_GEN1_EOF_CFG);
+	value &= ~XSEOF_OFFSET_MASK;
+	value |= SSG1EOF_OFFSET;
+	writel(value, hcd->regs + SS_GEN1_EOF_CFG);
+
+	value = readl(hcd->regs + SS_GEN2_EOF_CFG);
+	value &= ~XSEOF_OFFSET_MASK;
+	value |= SSG2EOF_OFFSET;
+	writel(value, hcd->regs + SS_GEN2_EOF_CFG);
+}
+
 static int xhci_mtk_host_enable(struct xhci_hcd_mtk *mtk)
 {
 	struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs;
@@ -368,6 +429,9 @@ static int xhci_mtk_setup(struct usb_hcd *hcd)
 		ret = xhci_mtk_ssusb_config(mtk);
 		if (ret)
 			return ret;
+
+		/* workaround only for mt8195 */
+		xhci_mtk_set_frame_interval(mtk);
 	}
 
 	ret = xhci_gen_setup(hcd, xhci_mtk_quirks);
@@ -716,6 +780,7 @@ static const struct dev_pm_ops xhci_mtk_pm_ops = {
 
 static const struct of_device_id mtk_xhci_of_match[] = {
 	{ .compatible = "mediatek,mt8173-xhci"},
+	{ .compatible = "mediatek,mt8195-xhci"},
 	{ .compatible = "mediatek,mtk-xhci"},
 	{ },
 };
Signature · 1 line
2.18.0
maintainer Reviewed-by on v1 1/9
#9 lore raw
In reply to Chunfeng Yun
Quoted 10 lines · Chunfeng Yun

Add support to disable specific usb2 host ports, it's useful when a usb2 port is disabled on some platforms, but enabled on others for the same SoC, another case is that the different package may support different number of ports.

---
 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml | 5 +++++
 1 file changed, 5 insertions(+)