Add QSPI and QUPv3 DT nodes for SC7280 SoC

index ef5698f..09aa955 100644
@@ -21,7 +21,10 @@ allOf:
 properties:
   compatible:
     items:
-      - const: qcom,sdm845-qspi
+      - enum:
+          - qcom,sc7280-qspi
+          - qcom,sdm845-qspi
+
       - const: qcom,qspi-v1
 
   reg:

index fd78f16..2fbcb0a 100644
@@ -415,6 +415,25 @@
 		method = "smc";
 	};
 
+	qspi_opp_table: qspi-opp-table {
+		compatible = "operating-points-v2";
+
+		opp-75000000 {
+			opp-hz = /bits/ 64 <75000000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-150000000 {
+			opp-hz = /bits/ 64 <150000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			required-opps = <&rpmhpd_opp_nom>;
+		};
+	};
+
 	soc: soc@0 {
 		#address-cells = <2>;
 		#size-cells = <2>;

@@ -1318,6 +1337,23 @@
 			};
 		};
 
+		qspi: spi@88dc000 {
+			compatible = "qcom,sc7280-qspi", "qcom,qspi-v1";
+			reg = <0 0x088dc000 0 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+				 <&gcc GCC_QSPI_CORE_CLK>;
+			clock-names = "iface", "core";
+			interconnects = <&gem_noc MASTER_APPSS_PROC 0
+					&cnoc2 SLAVE_QSPI_0 0>;
+			interconnect-names = "qspi-config";
+			power-domains = <&rpmhpd SC7280_CX>;
+			operating-points-v2 = <&qspi_opp_table>;
+			status = "disabled";
+		};
+
 		dc_noc: interconnect@90e0000 {
 			reg = <0 0x090e0000 0 0x5080>;
 			compatible = "qcom,sc7280-dc-noc";

@@ -1513,6 +1549,31 @@
 			gpio-ranges = <&tlmm 0 0 175>;
 			wakeup-parent = <&pdc>;
 
+			qspi_clk: qspi-clk {
+				pins = "gpio14";
+				function = "qspi_clk";
+			};
+
+			qspi_cs0: qspi-cs0 {
+				pins = "gpio15";
+				function = "qspi_cs";
+			};
+
+			qspi_cs1: qspi-cs1 {
+				pins = "gpio19";
+				function = "qspi_cs";
+			};
+
+			qspi_data01: qspi-data01 {
+				pins = "gpio12", "gpio13";
+				function = "qspi_data";
+			};
+
+			qspi_data12: qspi-data12 {
+				pins = "gpio16", "gpio17";
+				function = "qspi_data";
+			};
+
 			qup_uart5_default: qup-uart5-default {
 				pins = "gpio46", "gpio47";
 				function = "qup13";

index 99f9ee5..37b8444 100644
@@ -211,6 +211,20 @@
 	vcc-supply = <&vreg_l1c_1p8>;
 };
 
+&qspi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <37500000>;
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
+	};
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };

@@ -288,6 +302,19 @@
 
 /* PINCTRL - additions to nodes defined in sc7280.dtsi */
 
+&qspi_cs0 {
+	bias-disable;
+};
+
+&qspi_clk {
+	bias-disable;
+};
+
+&qspi_data01 {
+	/* High-Z when no transfers; nice to park the lines */
+	bias-pull-up;
+};
+
 &qup_uart5_default {
 	tx {
 		pins = "gpio46";

index 2fbcb0a..8278fd0 100644
@@ -434,6 +434,25 @@
 		};
 	};
 
+	qup_opp_table: qup-opp-table {
+		compatible = "operating-points-v2";
+
+		opp-75000000 {
+			opp-hz = /bits/ 64 <75000000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+
+		opp-128000000 {
+			opp-hz = /bits/ 64 <128000000>;
+			required-opps = <&rpmhpd_opp_nom>;
+		};
+	};
+
 	soc: soc@0 {
 		#address-cells = <2>;
 		#size-cells = <2>;

@@ -536,24 +555,425 @@
 		qupv3_id_0: geniqup@9c0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0 0x009c0000 0 0x2000>;
-			clock-names = "m-ahb", "s-ahb";
 			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
 				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+			clock-names = "m-ahb", "s-ahb";
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
+			iommus = <&apps_smmu 0x123 0x0>;
 			status = "disabled";
 
+			i2c0: i2c@980000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00980000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c0_data_clk>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi0: spi@980000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00980000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart0: serial@980000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00980000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart0_cts>, <&qup_uart0_rts>, <&qup_uart0_tx>, <&qup_uart0_rx>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c1: i2c@984000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00984000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c1_data_clk>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi1: spi@984000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00984000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart1: serial@984000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00984000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart1_cts>, <&qup_uart1_rts>, <&qup_uart1_tx>, <&qup_uart1_rx>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c2: i2c@988000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00988000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c2_data_clk>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi2: spi@988000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00988000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart2: serial@988000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00988000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart2_cts>, <&qup_uart2_rts>, <&qup_uart2_tx>, <&qup_uart2_rx>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c3: i2c@98c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x0098c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c3_data_clk>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi3: spi@98c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x0098c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart3: serial@98c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x0098c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart3_cts>, <&qup_uart3_rts>, <&qup_uart3_tx>, <&qup_uart3_rx>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c4: i2c@990000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00990000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c4_data_clk>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi4: spi@990000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00990000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart4: serial@990000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00990000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart4_cts>, <&qup_uart4_rts>, <&qup_uart4_tx>, <&qup_uart4_rx>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c5: i2c@994000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00994000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c5_data_clk>;
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi5: spi@994000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00994000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>;
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
 			uart5: serial@994000 {
 				compatible = "qcom,geni-debug-uart";
 				reg = <0 0x00994000 0 0x4000>;
-				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				clock-names = "se";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart5_default>;
 				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
 			};
+
+			i2c6: i2c@998000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00998000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c6_data_clk>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi6: spi@998000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00998000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart6: serial@998000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00998000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart6_cts>, <&qup_uart6_rts>, <&qup_uart6_tx>, <&qup_uart6_rx>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c7: i2c@99c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x0099c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c7_data_clk>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi7: spi@99c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x0099c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi7_data_clk>, <&qup_spi7_cs>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart7: serial@99c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x0099c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart7_cts>, <&qup_uart7_rts>, <&qup_uart7_tx>, <&qup_uart7_rx>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
 		};
 
 		cnoc2: interconnect@1500000 {

@@ -1574,11 +1994,311 @@
 				function = "qspi_data";
 			};
 
+			qup_i2c0_data_clk: qup-i2c0-data-clk {
+				pins = "gpio0", "gpio1";
+				function = "qup00";
+			};
+
+			qup_i2c1_data_clk: qup-i2c1-data-clk {
+				pins = "gpio4", "gpio5";
+				function = "qup01";
+			};
+
+			qup_i2c2_data_clk: qup-i2c2-data-clk {
+				pins = "gpio8", "gpio9";
+				function = "qup02";
+			};
+
+			qup_i2c3_data_clk: qup-i2c3-data-clk {
+				pins = "gpio12", "gpio13";
+				function = "qup03";
+			};
+
+			qup_i2c4_data_clk: qup-i2c4-data-clk {
+				pins = "gpio16", "gpio17";
+				function = "qup04";
+			};
+
+			qup_i2c5_data_clk: qup-i2c5-data-clk {
+				pins = "gpio20", "gpio21";
+				function = "qup05";
+			};
+
+			qup_i2c6_data_clk: qup-i2c6-data-clk {
+				pins = "gpio24", "gpio25";
+				function = "qup06";
+			};
+
+			qup_i2c7_data_clk: qup-i2c7-data-clk {
+				pins = "gpio28", "gpio29";
+				function = "qup07";
+			};
+
+			qup_spi0_data_clk: qup-spi0-data-clk {
+				pins = "gpio0", "gpio1", "gpio2";
+				function = "qup00";
+			};
+
+			qup_spi0_cs: qup-spi0-cs {
+				pins = "gpio3";
+				function = "qup00";
+			};
+
+			qup_spi0_cs_gpio: qup-spi0-cs-gpio {
+				pins = "gpio3";
+				function = "gpio";
+			};
+
+			qup_spi1_data_clk: qup-spi1-data-clk {
+				pins = "gpio4", "gpio5", "gpio6";
+				function = "qup01";
+			};
+
+			qup_spi1_cs: qup-spi1-cs {
+				pins = "gpio7";
+				function = "qup01";
+			};
+
+			qup_spi1_cs_gpio: qup-spi1-cs-gpio {
+				pins = "gpio7";
+				function = "gpio";
+			};
+
+			qup_spi2_data_clk: qup-spi2-data-clk {
+				pins = "gpio8", "gpio9", "gpio10";
+				function = "qup02";
+			};
+
+			qup_spi2_cs: qup-spi2-cs {
+				pins = "gpio11";
+				function = "qup02";
+			};
+
+			qup_spi2_cs_gpio: qup-spi2-cs-gpio {
+				pins = "gpio11";
+				function = "gpio";
+			};
+
+			qup_spi3_data_clk: qup-spi3-data-clk {
+				pins = "gpio12", "gpio13", "gpio14";
+				function = "qup03";
+			};
+
+			qup_spi3_cs: qup-spi3-cs {
+				pins = "gpio15";
+				function = "qup03";
+			};
+
+			qup_spi3_cs_gpio: qup-spi3-cs-gpio {
+				pins = "gpio15";
+				function = "gpio";
+			};
+
+			qup_spi4_data_clk: qup-spi4-data-clk {
+				pins = "gpio16", "gpio17", "gpio18";
+				function = "qup04";
+			};
+
+			qup_spi4_cs: qup-spi4-cs {
+				pins = "gpio19";
+				function = "qup04";
+			};
+
+			qup_spi4_cs_gpio: qup-spi4-cs-gpio {
+				pins = "gpio19";
+				function = "gpio";
+			};
+
+			qup_spi5_data_clk: qup-spi5-data-clk {
+				pins = "gpio20", "gpio21", "gpio22";
+				function = "qup05";
+			};
+
+			qup_spi5_cs: qup-spi5-cs {
+				pins = "gpio23";
+				function = "qup05";
+			};
+
+			qup_spi5_cs_gpio: qup-spi5-cs-gpio {
+				pins = "gpio23";
+				function = "gpio";
+			};
+
+			qup_spi6_data_clk: qup-spi6-data-clk {
+				pins = "gpio24", "gpio25", "gpio26";
+				function = "qup06";
+			};
+
+			qup_spi6_cs: qup-spi6-cs {
+				pins = "gpio27";
+				function = "qup06";
+			};
+
+			qup_spi6_cs_gpio: qup-spi6-cs-gpio {
+				pins = "gpio27";
+				function = "gpio";
+			};
+
+			qup_spi7_data_clk: qup-spi7-data-clk {
+				pins = "gpio28", "gpio29", "gpio30";
+				function = "qup07";
+			};
+
+			qup_spi7_cs: qup-spi7-cs {
+				pins = "gpio31";
+				function = "qup07";
+			};
+
+			qup_spi7_cs_gpio: qup-spi7-cs-gpio {
+				pins = "gpio31";
+				function = "gpio";
+			};
+
+			qup_uart0_cts: qup-uart0-cts {
+				pins = "gpio0";
+				function = "qup00";
+			};
+
+			qup_uart0_rts: qup-uart0-rts {
+				pins = "gpio1";
+				function = "qup00";
+			};
+
+			qup_uart0_tx: qup-uart0-tx {
+				pins = "gpio2";
+				function = "qup00";
+			};
+
+			qup_uart0_rx: qup-uart0-rx {
+				pins = "gpio3";
+				function = "qup00";
+			};
+
+			qup_uart1_cts: qup-uart1-cts {
+				pins = "gpio4";
+				function = "qup01";
+			};
+
+			qup_uart1_rts: qup-uart1-rts {
+				pins = "gpio5";
+				function = "qup01";
+			};
+
+			qup_uart1_tx: qup-uart1-tx {
+				pins = "gpio6";
+				function = "qup01";
+			};
+
+			qup_uart1_rx: qup-uart1-rx {
+				pins = "gpio7";
+				function = "qup01";
+			};
+
+			qup_uart2_cts: qup-uart2-cts {
+				pins = "gpio8";
+				function = "qup02";
+			};
+
+			qup_uart2_rts: qup-uart2-rts {
+				pins = "gpio9";
+				function = "qup02";
+			};
+
+			qup_uart2_tx: qup-uart2-tx {
+				pins = "gpio10";
+				function = "qup02";
+			};
+
+			qup_uart2_rx: qup-uart2-rx {
+				pins = "gpio11";
+				function = "qup02";
+			};
+
+			qup_uart3_cts: qup-uart3-cts {
+				pins = "gpio12";
+				function = "qup03";
+			};
+
+			qup_uart3_rts: qup-uart3-rts {
+				pins = "gpio13";
+				function = "qup03";
+			};
+
+			qup_uart3_tx: qup-uart3-tx {
+				pins = "gpio14";
+				function = "qup03";
+			};
+
+			qup_uart3_rx: qup-uart3-rx {
+				pins = "gpio15";
+				function = "qup03";
+			};
+
+			qup_uart4_cts: qup-uart4-cts {
+				pins = "gpio16";
+				function = "qup04";
+			};
+
+			qup_uart4_rts: qup-uart4-rts {
+				pins = "gpio17";
+				function = "qup04";
+			};
+
+			qup_uart4_tx: qup-uart4-tx {
+				pins = "gpio18";
+				function = "qup04";
+			};
+
+			qup_uart4_rx: qup-uart4-rx {
+				pins = "gpio19";
+				function = "qup04";
+			};
+
 			qup_uart5_default: qup-uart5-default {
 				pins = "gpio46", "gpio47";
 				function = "qup13";
 			};
 
+			qup_uart6_cts: qup-uart6-cts {
+				pins = "gpio24";
+				function = "qup06";
+			};
+
+			qup_uart6_rts: qup-uart6-rts {
+				pins = "gpio25";
+				function = "qup06";
+			};
+
+			qup_uart6_tx: qup-uart6-tx {
+				pins = "gpio26";
+				function = "qup06";
+			};
+
+			qup_uart6_rx: qup-uart6-rx {
+				pins = "gpio27";
+				function = "qup06";
+			};
+
+			qup_uart7_cts: qup-uart7-cts {
+				pins = "gpio28";
+				function = "qup07";
+			};
+
+			qup_uart7_rts: qup-uart7-rts {
+				pins = "gpio29";
+				function = "qup07";
+			};
+
+			qup_uart7_tx: qup-uart7-tx {
+				pins = "gpio30";
+				function = "qup07";
+			};
+
+			qup_uart7_rx: qup-uart7-rx {
+				pins = "gpio31";
+				function = "qup07";
+			};
+
 			sdc1_on: sdc1-on {
 				clk {
 					pins = "sdc1_clk";

index 37b8444..cf82301 100644
@@ -258,6 +258,7 @@
 };
 
 &uart5 {
+	compatible = "qcom,geni-debug-uart";
 	status = "okay";
 };
 

@@ -315,18 +316,14 @@
 	bias-pull-up;
 };
 
-&qup_uart5_default {
-	tx {
-		pins = "gpio46";
-		drive-strength = <2>;
-		bias-disable;
-	};
+&qup_uart5_tx {
+	drive-strength = <2>;
+	bias-disable;
+};
 
-	rx {
-		pins = "gpio47";
-		drive-strength = <2>;
-		bias-pull-up;
-	};
+&qup_uart5_rx {
+	drive-strength = <2>;
+	bias-pull-up;
 };
 
 &sdc1_on {

index 8278fd0..3254de65 100644
@@ -861,13 +861,18 @@
 			};
 
 			uart5: serial@994000 {
-				compatible = "qcom,geni-debug-uart";
+				compatible = "qcom,geni-uart";
 				reg = <0 0x00994000 0 0x4000>;
 				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
 				clock-names = "se";
 				pinctrl-names = "default";
-				pinctrl-0 = <&qup_uart5_default>;
+				pinctrl-0 = <&qup_uart5_cts>, <&qup_uart5_rts>, <&qup_uart5_tx>, <&qup_uart5_rx>;
 				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
 				status = "disabled";
 			};
 

@@ -2254,9 +2259,24 @@
 				function = "qup04";
 			};
 
-			qup_uart5_default: qup-uart5-default {
-				pins = "gpio46", "gpio47";
-				function = "qup13";
+			qup_uart5_cts: qup-uart5-cts {
+				pins = "gpio20";
+				function = "qup05";
+			};
+
+			qup_uart5_rts: qup-uart5-rts {
+				pins = "gpio21";
+				function = "qup05";
+			};
+
+			qup_uart5_tx: qup-uart5-tx {
+				pins = "gpio22";
+				function = "qup05";
+			};
+
+			qup_uart5_rx: qup-uart5-rx {
+				pins = "gpio23";
+				function = "qup05";
 			};
 
 			qup_uart6_cts: qup-uart6-cts {

index cf82301..52638e2 100644
@@ -301,6 +301,16 @@
 	vdda18-supply = <&vreg_l1c_1p8>;
 };
 
+&uart7 {
+	status = "okay";
+
+	/delete-property/interrupts;
+	interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
+				<&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
+};
+
 /* PINCTRL - additions to nodes defined in sc7280.dtsi */
 
 &qspi_cs0 {

@@ -326,6 +336,81 @@
 	bias-pull-up;
 };
 
+&qup_uart7_cts {
+	/*
+	 * Configure a pull-down on CTS to match the pull of
+	 * the Bluetooth module.
+	 */
+	bias-pull-down;
+};
+
+&qup_uart7_rts {
+	/* We'll drive RTS, so no pull */
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart7_tx {
+	/* We'll drive TX, so no pull */
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart7_rx {
+	/*
+	 * Configure a pull-up on RX. This is needed to avoid
+	 * garbage data when the TX pin of the Bluetooth module is
+	 * in tri-state (module powered off or not driving the
+	 * signal yet).
+	 */
+	bias-pull-up;
+};
+
+&tlmm {
+	qup_uart7_sleep_cts: qup-uart7-sleep-cts {
+		pins = "gpio28";
+		function = "gpio";
+		/*
+		 * Configure a pull-down on CTS to match the pull of
+		 * the Bluetooth module.
+		 */
+		bias-pull-down;
+	};
+
+	qup_uart7_sleep_rts: qup-uart7-sleep-rts {
+		pins = "gpio29";
+		function = "gpio";
+		/*
+		 * Configure pull-down on RTS. As RTS is active low
+		 * signal, pull it low to indicate the BT SoC that it
+		 * can wakeup the system anytime from suspend state by
+		 * pulling RX low (by sending wakeup bytes).
+		 */
+		bias-pull-down;
+	};
+
+	qup_uart7_sleep_tx: qup-uart7-sleep-tx {
+		pins = "gpio30";
+		function = "gpio";
+		/*
+		 * Configure pull-up on TX when it isn't actively driven
+		 * to prevent BT SoC from receiving garbage during sleep.
+		 */
+		bias-pull-up;
+	};
+
+	qup_uart7_sleep_rx: qup-uart7-sleep-rx {
+		pins = "gpio31";
+		function = "gpio";
+		/*
+		 * Configure a pull-up on RX. This is needed to avoid
+		 * garbage data when the TX pin of the Bluetooth module
+		 * is floating which may cause spurious wakeups.
+		 */
+		bias-pull-up;
+	};
+};
+
 &sdc1_on {
 	clk {
 		bias-disable;

index 52638e2..f2dc9f2 100644
@@ -229,6 +229,10 @@
 	status = "okay";
 };
 
+&qupv3_id_1 {
+	status = "okay";
+};
+
 &sdhc_1 {
 	status = "okay";
 

773 lines not on this page · raw message

index c26647a..e5fefd1 100644
@@ -26,8 +26,40 @@
 	chosen { };
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		i2c7 = &i2c7;
+		i2c8 = &i2c8;
+		i2c9 = &i2c9;
+		i2c10 = &i2c10;
+		i2c11 = &i2c11;
+		i2c12 = &i2c12;
+		i2c13 = &i2c13;
+		i2c14 = &i2c14;
+		i2c15 = &i2c15;
 		mmc1 = &sdhc_1;
 		mmc2 = &sdhc_2;
+		spi0 = &spi0;
+		spi1 = &spi1;
+		spi2 = &spi2;
+		spi3 = &spi3;
+		spi4 = &spi4;
+		spi5 = &spi5;
+		spi6 = &spi6;
+		spi7 = &spi7;
+		spi8 = &spi8;
+		spi9 = &spi9;
+		spi10 = &spi10;
+		spi11 = &spi11;
+		spi12 = &spi12;
+		spi13 = &spi13;
+		spi14 = &spi14;
+		spi15 = &spi15;
 	};
 
 	clocks {