Skip to contentSkip to conversation

arm64: dts: qcom: msm8916-longcheer-l8150: Add missing sensor interrupts

PATCH Applied Stephan Gerhold 3 participants 3 messages Aug 16, 2021 – Sep 27, 2021

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 arm64: dts: qcom: msm8916-longcheer-l8150: Add missing sensor interrupts

So far there were no interrupts set up for the BMC150 accelerometer
+ magnetometer combo because they were broken for some reason. It turns out Longcheer L8150 actually has a BMC156 which is very similar to BMC150, but only has an INT2 pin for the accelerometer part.

This requires some minor changes in the bmc150-accel driver which is now supported by using the more correct bosch,bmc156_accel compatible. Unfortunately it looks like even INT2 is not functional on most boards because the interrupt line is not actually connected to the BMC156. However, there are two pads next to the chip that can be shorted to make it work if needed.

While at it, add the missing interrupts for the magnetometer part and extra BMG160 gyroscope, those seem to work without any problems. Also correct the magnetometer compatible to bosch,bmc156_magn for clarity (no functional difference for the magnetometer part).

---
 .../boot/dts/qcom/msm8916-longcheer-l8150.dts | 43 +++++++++++++++++--
 1 file changed, 39 insertions(+), 4 deletions(-)
arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts +39 -4
index 1e893c0b6fbc..30716eb8fb2d 100644
@@ -121,9 +121,21 @@ &blsp_i2c2 {
 	status = "okay";
 
 	accelerometer@10 {
-		compatible = "bosch,bmc150_accel";
+		compatible = "bosch,bmc156_accel";
 		reg = <0x10>;
 
+		/*
+		 * For some reason the interrupt line is usually not connected
+		 * to the BMC156. However, there are two pads next to the chip
+		 * that can be shorted to make it work if needed.
+		 *
+		 * interrupt-parent = <&msmgpio>;
+		 * interrupts = <116 IRQ_TYPE_EDGE_RISING>;
+		 */
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&accel_int_default>;
+
 		vdd-supply = <&pm8916_l17>;
 		vddio-supply = <&pm8916_l6>;
 
@@ -133,9 +145,15 @@ accelerometer@10 {
 	};
 
 	magnetometer@12 {
-		compatible = "bosch,bmc150_magn";
+		compatible = "bosch,bmc156_magn";
 		reg = <0x12>;
 
+		interrupt-parent = <&msmgpio>;
+		interrupts = <113 IRQ_TYPE_EDGE_RISING>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&magn_int_default>;
+
 		vdd-supply = <&pm8916_l17>;
 		vddio-supply = <&pm8916_l6>;
 	};
@@ -145,7 +163,8 @@ gyroscope@68 {
 		reg = <0x68>;
 
 		interrupt-parent = <&msmgpio>;
-		interrupts = <23 IRQ_TYPE_EDGE_RISING>;
+		interrupts = <23 IRQ_TYPE_EDGE_RISING>,
+			     <22 IRQ_TYPE_EDGE_RISING>;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&gyro_int_default>;
@@ -336,6 +355,14 @@ l18 {
 };
 
 &msmgpio {
+	accel_int_default: accel-int-default {
+		pins = "gpio116";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	camera_flash_default: camera-flash-default {
 		pins = "gpio31", "gpio32";
 		function = "gpio";
@@ -361,7 +388,15 @@ gpio_keys_default: gpio-keys-default {
 	};
 
 	gyro_int_default: gyro-int-default {
-		pins = "gpio23";
+		pins = "gpio22", "gpio23";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	magn_int_default: magn-int-default {
+		pins = "gpio113";
 		function = "gpio";
 
 		drive-strength = <2>;
Signature · 1 line
2.32.0
#1 lore raw

Re: (subset) [PATCH] arm64: dts: qcom: msm8916-longcheer-l8150: Add missing sensor interrupts

Quoted 5 lines · Stephan Gerhold

So far there were no interrupts set up for the BMC150 accelerometer
+ magnetometer combo because they were broken for some reason. It turns out Longcheer L8150 actually has a BMC156 which is very similar to BMC150, but only has an INT2 pin for the accelerometer part.

Quoted 8 lines

This requires some minor changes in the bmc150-accel driver which is now supported by using the more correct bosch,bmc156_accel compatible. Unfortunately it looks like even INT2 is not functional on most boards because the interrupt line is not actually connected to the BMC156. However, there are two pads next to the chip that can be shorted to make it work if needed.

[...]

Applied, thanks!

[1/1] arm64: dts: qcom: msm8916-longcheer-l8150: Add missing sensor interrupts

      commit: 51c7786f5d4201422e076b9a3650e543a61d36da

Best regards,

Signature · 1 line
Bjorn Andersson <[email protected]>
#2 lore raw
In reply to Stephan Gerhold
This patch was applied to qcom/linux.git (refs/heads/for-next):

Hello:

This patch was applied to qcom/linux.git (refs/heads/for-next):

Quoted 5 lines · On Mon, 16 Aug 2021 14:35:44 +0200 you wrote:

So far there were no interrupts set up for the BMC150 accelerometer
+ magnetometer combo because they were broken for some reason. It turns out Longcheer L8150 actually has a BMC156 which is very similar to BMC150, but only has an INT2 pin for the accelerometer part.

Quoted 8 lines

This requires some minor changes in the bmc150-accel driver which is now supported by using the more correct bosch,bmc156_accel compatible. Unfortunately it looks like even INT2 is not functional on most boards because the interrupt line is not actually connected to the BMC156. However, there are two pads next to the chip that can be shorted to make it work if needed.

[...]

Here is the summary with links:
- arm64: dts: qcom: msm8916-longcheer-l8150: Add missing sensor interrupts

    https://git.kernel.org/qcom/c/51c7786f5d42

You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html