Skip to contentSkip to conversation

net: phy: marvell: add Marvell specific PHY loopback

PATCH Applied Mohammad Athari Bin Ismail 2 participants 2 messages Jan 15, 2022

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH v4 1/1 net: phy: marvell: add Marvell specific PHY loopback

Existing genphy_loopback() is not applicable for Marvell PHY. Besides configuring bit-6 and bit-13 in Page 0 Register 0 (Copper Control Register), it is also required to configure same bits in Page 2 Register 21 (MAC Specific Control Register 2) according to speed of the loopback is operating.

Tested working on Marvell88E1510 PHY for all speeds (1000/100/10Mbps).

FIXME: Based on trial and error test, it seem 1G need to have delay between soft reset and loopback enablement.

Fixes 014068dcb5b1 ("net: phy: genphy_loopback: add link speed configuration")
Cc <[email protected]> # 5.15.x

---
v4 changelog:
- Rename the function to m88e1510_loopback(). Commented by Heiner Kallweit <[email protected]>.

v3 changelog:
- Use phy_write() to configure speed for BMCR.
- Add error handling.
All commented by Russell King <[email protected]>

v2 changelog:
- For loopback enabled, add bit-6 and bit-13 configuration in both Page 0 Register 0 and Page 2 Register 21. Commented by Heiner Kallweit
<[email protected]>.
- For loopback disabled, follow genphy_loopback() implementation

---
 drivers/net/phy/marvell.c | 56 ++++++++++++++++++++++++++++++++++++++-
 1 file changed, 55 insertions(+), 1 deletion(-)
drivers/net/phy/marvell.c +55 -1
index 4fcfca4e1702..0ff94400510f 100644
@@ -189,6 +189,8 @@
 #define MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_SGMII	0x4
 #define MII_88E1510_GEN_CTRL_REG_1_RESET	0x8000	/* Soft reset */
 
+#define MII_88E1510_MSCR_2		0x15
+
 #define MII_VCT5_TX_RX_MDI0_COUPLING	0x10
 #define MII_VCT5_TX_RX_MDI1_COUPLING	0x11
 #define MII_VCT5_TX_RX_MDI2_COUPLING	0x12
@@ -1932,6 +1934,58 @@ static void marvell_get_stats(struct phy_device *phydev,
 		data[i] = marvell_get_stat(phydev, i);
 }
 
+static int m88e1510_loopback(struct phy_device *phydev, bool enable)
+{
+	int err;
+
+	if (enable) {
+		u16 bmcr_ctl = 0, mscr2_ctl = 0;
+
+		if (phydev->speed == SPEED_1000)
+			bmcr_ctl = BMCR_SPEED1000;
+		else if (phydev->speed == SPEED_100)
+			bmcr_ctl = BMCR_SPEED100;
+
+		if (phydev->duplex == DUPLEX_FULL)
+			bmcr_ctl |= BMCR_FULLDPLX;
+
+		err = phy_write(phydev, MII_BMCR, bmcr_ctl);
+		if (err < 0)
+			return err;
+
+		if (phydev->speed == SPEED_1000)
+			mscr2_ctl = BMCR_SPEED1000;
+		else if (phydev->speed == SPEED_100)
+			mscr2_ctl = BMCR_SPEED100;
+
+		err = phy_modify_paged(phydev, MII_MARVELL_MSCR_PAGE,
+				       MII_88E1510_MSCR_2, BMCR_SPEED1000 |
+				       BMCR_SPEED100, mscr2_ctl);
+		if (err < 0)
+			return err;
+
+		/* Need soft reset to have speed configuration takes effect */
+		err = genphy_soft_reset(phydev);
+		if (err < 0)
+			return err;
+
+		/* FIXME: Based on trial and error test, it seem 1G need to have
+		 * delay between soft reset and loopback enablement.
+		 */
+		if (phydev->speed == SPEED_1000)
+			msleep(1000);
+
+		return phy_modify(phydev, MII_BMCR, BMCR_LOOPBACK,
+				  BMCR_LOOPBACK);
+	} else {
+		err = phy_modify(phydev, MII_BMCR, BMCR_LOOPBACK, 0);
+		if (err < 0)
+			return err;
+
+		return phy_config_aneg(phydev);
+	}
+}
+
 static int marvell_vct5_wait_complete(struct phy_device *phydev)
 {
 	int i;
@@ -3078,7 +3132,7 @@ static struct phy_driver marvell_drivers[] = {
 		.get_sset_count = marvell_get_sset_count,
 		.get_strings = marvell_get_strings,
 		.get_stats = marvell_get_stats,
-		.set_loopback = genphy_loopback,
+		.set_loopback = m88e1510_loopback,
 		.get_tunable = m88e1011_get_tunable,
 		.set_tunable = m88e1011_set_tunable,
 		.cable_test_start = marvell_vct7_cable_test_start,
Signature · 1 line
2.17.1
#1 lore raw
This patch was applied to netdev/net.git (master) by David S. Miller <[email protected]>:

Hello:

This patch was applied to netdev/net.git (master)
by David S. Miller <[email protected]>:

Quoted 9 lines · On Sat, 15 Jan 2022 17:25:15 +0800 you wrote:

Existing genphy_loopback() is not applicable for Marvell PHY. Besides configuring bit-6 and bit-13 in Page 0 Register 0 (Copper Control Register), it is also required to configure same bits in Page 2 Register 21 (MAC Specific Control Register 2) according to speed of the loopback is operating.

Tested working on Marvell88E1510 PHY for all speeds (1000/100/10Mbps).

[...]

Here is the summary with links:
- [net,v4] net: phy: marvell: add Marvell specific PHY loopback

    https://git.kernel.org/netdev/net/c/020a45aff119

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html